--- /dev/null
+--- a/arch/mips/Kconfig
++++ b/arch/mips/Kconfig
+@@ -18,6 +18,21 @@
+ prompt "System type"
+ default SGI_IP22
+
++config MIPS_ADM5120
++ bool "ADM5120 SoC based machines"
++ select CEVT_R4K
++ select CSRC_R4K
++ select SYS_HAS_CPU_MIPS32_R1
++ select SYS_HAS_EARLY_PRINTK
++ select DMA_NONCOHERENT
++ select HW_HAS_PCI
++ select IRQ_CPU
++ select SYS_SUPPORTS_LITTLE_ENDIAN
++ select SYS_SUPPORTS_BIG_ENDIAN
++ select SYS_SUPPORTS_32BIT_KERNEL
++ select GENERIC_GPIO
++ select SWAP_IO_SPACE if CPU_BIG_ENDIAN
++
+ config MACH_ALCHEMY
+ bool "Alchemy processor based machines"
+
+@@ -687,6 +702,7 @@
+
+ endchoice
+
++source "arch/mips/adm5120/Kconfig"
+ source "arch/mips/au1000/Kconfig"
+ source "arch/mips/basler/excite/Kconfig"
+ source "arch/mips/jazz/Kconfig"
+--- a/arch/mips/Makefile
++++ b/arch/mips/Makefile
+@@ -174,6 +174,16 @@
+ load-$(CONFIG_MACH_JAZZ) += 0xffffffff80080000
+
+ #
++# ADMtek 5120
++#
++
++libs-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/prom/
++core-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/
++core-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/boards/
++cflags-$(CONFIG_MIPS_ADM5120) += -Iinclude/asm-mips/mach-adm5120
++load-$(CONFIG_MIPS_ADM5120) += 0xffffffff80001000
++
++#
+ # Common Alchemy Au1x00 stuff
+ #
+ core-$(CONFIG_SOC_AU1X00) += arch/mips/au1000/common/
+--- a/include/asm-mips/bootinfo.h
++++ b/include/asm-mips/bootinfo.h
+@@ -94,6 +94,58 @@
+ #define MACH_MSP7120_FPGA 5 /* PMC-Sierra MSP7120 Emulation */
+ #define MACH_MSP_OTHER 255 /* PMC-Sierra unknown board type */
+
++/*
++ * Valid machtype for group ADMtek ADM5120
++ */
++#define MACH_ADM5120_GENERIC 0 /* Generic board */
++#define MACH_ADM5120_WP54G_WRT 1 /* Compex WP54G-WRT */
++#define MACH_ADM5120_WP54G 2 /* Compex WP54G */
++#define MACH_ADM5120_WP54AG 3 /* Compex WP54AG */
++#define MACH_ADM5120_WPP54G 4 /* Compex WPP54G */
++#define MACH_ADM5120_WPP54AG 5 /* Compex WPP54AG */
++#define MACH_ADM5120_NP28G 6 /* Compex NP28G */
++#define MACH_ADM5120_NP28GHS 7 /* Compex NP28G HotSpot */
++#define MACH_ADM5120_NP27G 8 /* Compex NP27G */
++#define MACH_ADM5120_WP54Gv1C 9 /* Compex WP54G version 1C */
++#define MACH_ADM5120_RB_111 10 /* Mikrotik RouterBOARD 111 */
++#define MACH_ADM5120_RB_112 11 /* Mikrotik RouterBOARD 112 */
++#define MACH_ADM5120_RB_133 12 /* Mikrotik RouterBOARD 133 */
++#define MACH_ADM5120_RB_133C 13 /* Mikrotik RouterBOARD 133c */
++#define MACH_ADM5120_RB_150 14 /* Mikrotik RouterBOARD 150 */
++#define MACH_ADM5120_RB_153 15 /* Mikrotik RouterBOARD 153 */
++#define MACH_ADM5120_HS100 16 /* ZyXEL HomeSafe 100/100W */
++#define MACH_ADM5120_P334 17 /* ZyXEL Prestige 334 */
++#define MACH_ADM5120_P334U 18 /* ZyXEL Prestige 334U */
++#define MACH_ADM5120_P334W 19 /* ZyXEL Prestige 334W */
++#define MACH_ADM5120_P334WH 20 /* ZyXEL Prestige 334WH */
++#define MACH_ADM5120_P334WHD 21 /* ZyXEL Prestige 334WHD */
++#define MACH_ADM5120_P334WT 22 /* ZyXEL Prestige 334WT */
++#define MACH_ADM5120_P335 23 /* ZyXEL Prestige 335/335WT */
++#define MACH_ADM5120_P335PLUS 24 /* ZyXEL Prestige 335Plus */
++#define MACH_ADM5120_P335U 25 /* ZyXEL Prestige 335U */
++#define MACH_ADM5120_ES2108 26 /* ZyXEL Ethernet Switch 2108 */
++#define MACH_ADM5120_ES2108F 27 /* ZyXEL Ethernet Switch 2108-F */
++#define MACH_ADM5120_ES2108G 28 /* ZyXEL Ethernet Switch 2108-G */
++#define MACH_ADM5120_ES2108LC 29 /* ZyXEL Ethernet Switch 2108-LC */
++#define MACH_ADM5120_ES2108PWR 30 /* ZyXEL Ethernet Switch 2108-PWR */
++#define MACH_ADM5120_ES2024A 31 /* ZyXEL Ethernet Switch 2024A */
++#define MACH_ADM5120_ES2024PWR 32 /* ZyXEL Ethernet Switch 2024PWR */
++#define MACH_ADM5120_CAS630 33 /* Cellvision CAS-630/630W */
++#define MACH_ADM5120_CAS670 34 /* Cellvision CAS-670/670W */
++#define MACH_ADM5120_CAS700 36 /* Cellvision CAS-700/700W */
++#define MACH_ADM5120_CAS771 37 /* Cellvision CAS-771/771W */
++#define MACH_ADM5120_CAS790 38 /* Cellvision CAS-790 */
++#define MACH_ADM5120_CAS861 39 /* Cellvision CAS-861/861W */
++#define MACH_ADM5120_NFS101U 40 /* Cellvision NFS-101U/101WU */
++#define MACH_ADM5120_NFS202U 41 /* Cellvision NFS-202U/202WU */
++#define MACH_ADM5120_EASY5120PATA 42 /* Infineon EASY 5120P-ATA */
++#define MACH_ADM5120_EASY5120RT 43 /* Infineon EASY 5120-RT */
++#define MACH_ADM5120_EASY5120WVOIP 44 /* Infineon EASY 5120-WVoIP */
++#define MACH_ADM5120_EASY83000 45 /* Infineon EASY-83000 */
++#define MACH_ADM5120_BR6104K 46 /* Edimax BR-6104K/BR-6104KP */
++#define MACH_ADM5120_RB_192 47 /* Mikrotik RouterBOARD 192 */
++#define MACH_ADM5120_BR61x4WG 48 /* Edimax BR-6104Wg/BR-6114WG */
++
+ #define CL_SIZE COMMAND_LINE_SIZE
+
+ extern char *system_type;
--- /dev/null
+--- a/drivers/mtd/maps/Kconfig
++++ b/drivers/mtd/maps/Kconfig
+@@ -586,5 +586,9 @@
+
+ This selection automatically selects the map_ram driver.
+
++config MTD_ADM5120
++ tristate "Map driver for ADM5120 based boards"
++ depends on MIPS_ADM5120
++
+ endmenu
+
+--- a/drivers/mtd/maps/Makefile
++++ b/drivers/mtd/maps/Makefile
+@@ -44,6 +44,7 @@
+ obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o
+ obj-$(CONFIG_MTD_PCI) += pci.o
+ obj-$(CONFIG_MTD_ALCHEMY) += alchemy-flash.o
++obj-$(CONFIG_MTD_ADM5120) += adm5120-flash.o
+ obj-$(CONFIG_MTD_AUTCPU12) += autcpu12-nvram.o
+ obj-$(CONFIG_MTD_EDB7312) += edb7312.o
+ obj-$(CONFIG_MTD_IMPA7) += impa7.o
--- /dev/null
+--- a/drivers/net/Kconfig
++++ b/drivers/net/Kconfig
+@@ -613,6 +613,10 @@
+ If you have an Alchemy Semi AU1X00 based system
+ say Y. Otherwise, say N.
+
++config MIPS_ADM5120_ENET
++ tristate "MIPS ADM5120 Ethernet switch support"
++ depends on MIPS_ADM5120
++
+ config SGI_IOC3_ETH
+ bool "SGI IOC3 Ethernet"
+ depends on PCI && SGI_IP27
+--- a/drivers/net/Makefile
++++ b/drivers/net/Makefile
+@@ -186,6 +186,7 @@
+ # This is also a 82596 and should probably be merged
+ obj-$(CONFIG_LP486E) += lp486e.o
+
++obj-$(CONFIG_MIPS_ADM5120_ENET) += adm5120sw.o
+ obj-$(CONFIG_ETH16I) += eth16i.o
+ obj-$(CONFIG_ZORRO8390) += zorro8390.o
+ obj-$(CONFIG_HPLANCE) += hplance.o 7990.o
--- /dev/null
+--- a/drivers/usb/host/Kconfig
++++ b/drivers/usb/host/Kconfig
+@@ -4,6 +4,10 @@
+ comment "USB Host Controller Drivers"
+ depends on USB
+
++config USB_ADM5120_HCD
++ tristate "ADM5120 HCD support (EXPERIMENTAL)"
++ depends on USB && MIPS_ADM5120 && EXPERIMENTAL
++
+ config USB_C67X00_HCD
+ tristate "Cypress C67x00 HCD support"
+ depends on USB
+--- a/drivers/usb/host/Makefile
++++ b/drivers/usb/host/Makefile
+@@ -10,6 +10,7 @@
+
+ obj-$(CONFIG_PCI) += pci-quirks.o
+
++obj-$(CONFIG_USB_ADM5120_HCD) += adm5120-hcd.o
+ obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o
+ obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o
+ obj-$(CONFIG_USB_OHCI_HCD) += ohci-hcd.o
+--- a/drivers/usb/Makefile
++++ b/drivers/usb/Makefile
+@@ -16,6 +16,7 @@
+ obj-$(CONFIG_USB_SL811_HCD) += host/
+ obj-$(CONFIG_USB_U132_HCD) += host/
+ obj-$(CONFIG_USB_R8A66597_HCD) += host/
++obj-$(CONFIG_USB_ADM5120_HCD) += host/
+
+ obj-$(CONFIG_USB_C67X00_HCD) += c67x00/
+
--- /dev/null
+--- a/drivers/leds/Kconfig
++++ b/drivers/leds/Kconfig
+@@ -24,6 +24,21 @@
+ This option enables support for LEDs driven using outputs
+ of the dedicated PWM controller found on newer Atmel SOCs.
+
++config LEDS_ADM5120
++ tristate "LED Support for ADM5120 GPIO LEDs"
++ depends on LEDS_GPIO && MIPS_ADM5120
++ help
++ This option enables support for LEDs connected to GPIO lines
++ on ADM5120 SoC based platforms.
++
++config LEDS_ADM5120_EXPERIMENTAL
++ bool "Enable ADM5120 LEDs experimental code"
++ depends on LEDS_ADM5120
++
++config LEDS_ADM5120_DIAG
++ bool "Enable ADM5120 LEDs diagnostic mode"
++ depends on LEDS_ADM5120
++
+ config LEDS_CORGI
+ tristate "LED Support for the Sharp SL-C7x0 series"
+ depends on LEDS_CLASS && PXA_SHARP_C7xx
+--- a/drivers/leds/Makefile
++++ b/drivers/leds/Makefile
+@@ -5,6 +5,7 @@
+ obj-$(CONFIG_LEDS_TRIGGERS) += led-triggers.o
+
+ # LED Platform Drivers
++obj-$(CONFIG_LEDS_ADM5120) += leds-adm5120.o
+ obj-$(CONFIG_LEDS_ATMEL_PWM) += leds-atmel-pwm.o
+ obj-$(CONFIG_LEDS_CORGI) += leds-corgi.o
+ obj-$(CONFIG_LEDS_LOCOMO) += leds-locomo.o
--- /dev/null
+--- a/arch/mips/pci/Makefile
++++ b/arch/mips/pci/Makefile
+@@ -48,3 +48,4 @@
+ obj-$(CONFIG_VICTOR_MPC30X) += fixup-mpc30x.o
+ obj-$(CONFIG_ZAO_CAPCELLA) += fixup-capcella.o
+ obj-$(CONFIG_WR_PPMC) += fixup-wrppmc.o
++obj-$(CONFIG_PCI_ADM5120) += pci-adm5120.o
+--- a/include/linux/pci_ids.h
++++ b/include/linux/pci_ids.h
+@@ -1707,6 +1707,9 @@
+ #define PCI_VENDOR_ID_ESDGMBH 0x12fe
+ #define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111
+
++#define PCI_VENDOR_ID_ADMTEK 0x1317
++#define PCI_DEVICE_ID_ADMTEK_ADM5120 0x5120
++
+ #define PCI_VENDOR_ID_SIIG 0x131f
+ #define PCI_SUBVENDOR_ID_SIIG 0x131f
+ #define PCI_DEVICE_ID_SIIG_1S_10x_550 0x1000
--- /dev/null
+--- a/drivers/leds/Kconfig
++++ b/drivers/leds/Kconfig
+@@ -215,4 +215,12 @@
+ tristate "LED Morse Trigger"
+ depends on LEDS_TRIGGERS
+
++config LEDS_TRIGGER_ADM5120_SWITCH
++ tristate "LED ADM5120 Switch Port Status Trigger"
++ depends on LEDS_TRIGGERS && LEDS_ADM5120
++ help
++ This allows LEDs to be controlled by the port states of
++ the ADM5120 built-in Ethernet Switch
++ If unsure, say N.
++
+ endif # NEW_LEDS
+--- a/drivers/leds/Makefile
++++ b/drivers/leds/Makefile
+@@ -30,3 +30,4 @@
+ obj-$(CONFIG_LEDS_TRIGGER_HEARTBEAT) += ledtrig-heartbeat.o
+ obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON) += ledtrig-default-on.o
+ obj-$(CONFIG_LEDS_TRIGGER_MORSE) += ledtrig-morse.o
++obj-$(CONFIG_LEDS_TRIGGER_ADM5120_SWITCH) += ledtrig-adm5120-switch.o
--- /dev/null
+--- a/drivers/mtd/Kconfig
++++ b/drivers/mtd/Kconfig
+@@ -174,6 +174,22 @@
+ ---help---
+ TI AR7 partitioning support
+
++config MTD_MYLOADER_PARTS
++ tristate "MyLoader partition parsing"
++ depends on MIPS_ADM5120 && MTD_PARTITIONS
++ ---help---
++ MyLoader is a bootloader which allows the user to define partitions
++ in flash devices, by putting a table in the second erase block
++ on the device, similar to a partition table. This table gives the
++ offsets and lengths of the user defined partitions.
++
++ If you need code which can detect and parse these tables, and
++ register MTD 'partitions' corresponding to each image detected,
++ enable this option.
++
++ You will still need the parsing functions to be called by the driver
++ for your particular device. It won't happen automatically.
++
+ comment "User Modules And Translation Layers"
+
+ config MTD_CHAR
+--- a/drivers/mtd/Makefile
++++ b/drivers/mtd/Makefile
+@@ -13,6 +13,7 @@
+ obj-$(CONFIG_MTD_AFS_PARTS) += afs.o
+ obj-$(CONFIG_MTD_AR7_PARTS) += ar7part.o
+ obj-$(CONFIG_MTD_OF_PARTS) += ofpart.o
++obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o
+
+ # 'Users' - code which presents functionality to userspace.
+ obj-$(CONFIG_MTD_CHAR) += mtdchar.o
--- /dev/null
+--- a/drivers/mtd/chips/cfi_cmdset_0002.c
++++ b/drivers/mtd/chips/cfi_cmdset_0002.c
+@@ -47,12 +47,19 @@
+ #define MANUFACTURER_AMD 0x0001
+ #define MANUFACTURER_ATMEL 0x001F
+ #define MANUFACTURER_SST 0x00BF
++#define MANUFACTURER_MACRONIX 0x00C2
+ #define SST49LF004B 0x0060
+ #define SST49LF040B 0x0050
+ #define SST49LF008A 0x005a
+ #define AT49BV6416 0x00d6
+ #define MANUFACTURER_SAMSUNG 0x00ec
+
++/* Macronix */
++#define MX29LV160B 0x2249 /* MX29LV160 Bottom-boot chip */
++#define MX29LV160T 0x22C4 /* MX29LV160 Top-boot chip */
++#define MX29LV320B 0x22A8 /* MX29LV320 Bottom-boot chip */
++#define MX29LV320T 0x22A7 /* MX29LV320 Top-boot chip */
++
+ static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *);
+ static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+ static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *);
+@@ -243,6 +250,41 @@
+ }
+ }
+
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++/*
++ * Some Macronix chips has no/bad bootblock information in the CFI table
++ */
++static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param)
++{
++ struct map_info *map = mtd->priv;
++ struct cfi_private *cfi = map->fldrv_priv;
++ struct cfi_pri_amdstd *extp = cfi->cmdset_priv;
++ __u8 t;
++
++ switch (cfi->id) {
++ /* TODO: put affected chip ids here */
++ case MX29LV160B:
++ case MX29LV320B:
++ t = 2; /* Bottom boot */
++ break;
++ case MX29LV160T:
++ case MX29LV320T:
++ t = 3; /* Top boot */
++ break;
++ default:
++ return;
++ }
++
++ if (extp->TopBottom == t)
++ /* boot location detected by the CFI layer is correct */
++ return;
++
++ extp->TopBottom = t;
++ printk("%s: Macronix chip detected, id:0x%04X, boot location forced "
++ "to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top");
++}
++#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */
++
+ static struct cfi_fixup cfi_fixup_table[] = {
+ { CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL },
+ #ifdef AMD_BOOTLOC_BUG
+@@ -278,6 +320,9 @@
+ */
+ { CFI_MFR_ANY, CFI_ID_ANY, fixup_use_erase_chip, NULL },
+ { CFI_MFR_ATMEL, AT49BV6416, fixup_use_atmel_lock, NULL },
++#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++ { MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, },
++#endif
+ { 0, 0, NULL, NULL }
+ };
+
+--- a/drivers/mtd/chips/Kconfig
++++ b/drivers/mtd/chips/Kconfig
+@@ -196,6 +196,14 @@
+ provides support for one of those command sets, used on chips
+ including the AMD Am29LV320.
+
++config MTD_CFI_FIXUP_MACRONIX_BOOTLOC
++ bool "Fix boot-block location for Macronix flash chips"
++ depends on MTD_CFI_AMDSTD
++ help
++ Some Macronix flash chips have no/wrong boot-block location in the
++ CFI table, and the driver may detect the type incorrectly. Select
++ this if your board has such chip.
++
+ config MTD_CFI_STAA
+ tristate "Support for ST (Advanced Architecture) flash chips"
+ depends on MTD_GEN_PROBE
--- /dev/null
+--- a/drivers/mtd/chips/jedec_probe.c
++++ b/drivers/mtd/chips/jedec_probe.c
+@@ -121,6 +121,10 @@
+ #define UPD29F064115 0x221C
+
+ /* PMC */
++#define PM39LV512 0x001B
++#define PM39LV010 0x001C
++#define PM39LV020 0x003D
++#define PM39LV040 0x003E
+ #define PM49FL002 0x006D
+ #define PM49FL004 0x006E
+ #define PM49FL008 0x006A
+@@ -1173,6 +1177,54 @@
+ ERASEINFO(0x02000,2),
+ ERASEINFO(0x04000,1),
+ }
++ }, {
++ .mfr_id = MANUFACTURER_PMC,
++ .dev_id = PM39LV512,
++ .name = "PMC Pm39LV512",
++ .devtypes = CFI_DEVICETYPE_X8,
++ .uaddr = MTD_UADDR_0x0555_0x02AA,
++ .dev_size = SIZE_64KiB,
++ .cmd_set = P_ID_AMD_STD,
++ .nr_regions = 1,
++ .regions = {
++ ERASEINFO(0x01000,16),
++ }
++ }, {
++ .mfr_id = MANUFACTURER_PMC,
++ .dev_id = PM39LV010,
++ .name = "PMC Pm39LV010",
++ .devtypes = CFI_DEVICETYPE_X8,
++ .uaddr = MTD_UADDR_0x0555_0x02AA,
++ .dev_size = SIZE_128KiB,
++ .cmd_set = P_ID_AMD_STD,
++ .nr_regions = 1,
++ .regions = {
++ ERASEINFO(0x01000,32),
++ }
++ }, {
++ .mfr_id = MANUFACTURER_PMC,
++ .dev_id = PM39LV020,
++ .name = "PMC Pm39LV020",
++ .devtypes = CFI_DEVICETYPE_X8,
++ .uaddr = MTD_UADDR_0x0555_0x02AA,
++ .dev_size = SIZE_256KiB,
++ .cmd_set = P_ID_AMD_STD,
++ .nr_regions = 1,
++ .regions = {
++ ERASEINFO(0x01000,64),
++ }
++ }, {
++ .mfr_id = MANUFACTURER_PMC,
++ .dev_id = PM39LV040,
++ .name = "PMC Pm39LV040",
++ .devtypes = CFI_DEVICETYPE_X8,
++ .uaddr = MTD_UADDR_0x0555_0x02AA,
++ .dev_size = SIZE_512KiB,
++ .cmd_set = P_ID_AMD_STD,
++ .nr_regions = 1,
++ .regions = {
++ ERASEINFO(0x01000,128),
++ }
+ }, {
+ .mfr_id = MANUFACTURER_PMC,
+ .dev_id = PM49FL002,
--- /dev/null
+--- a/drivers/mtd/Kconfig
++++ b/drivers/mtd/Kconfig
+@@ -57,6 +57,11 @@
+ depends on MTD_PARTITIONS
+ default y
+
++config MTD_TRXSPLIT
++ bool "Automatically find and split TRX partitions"
++ depends on MTD_PARTITIONS
++ default n
++
+ config MTD_REDBOOT_PARTS
+ tristate "RedBoot partition table parsing"
+ depends on MTD_PARTITIONS
+--- a/drivers/mtd/Makefile
++++ b/drivers/mtd/Makefile
+@@ -8,6 +8,7 @@
+ mtd-$(CONFIG_MTD_PARTITIONS) += mtdpart.o
+
+ obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o
++obj-$(CONFIG_MTD_TRXSPLIT) += trxsplit.o
+ obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o
+ obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o
+ obj-$(CONFIG_MTD_AFS_PARTS) += afs.o
--- /dev/null
+--- a/drivers/ata/Makefile
++++ b/drivers/ata/Makefile
+@@ -72,6 +72,7 @@
+ obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o
+ obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o
+ obj-$(CONFIG_PATA_ICSIDE) += pata_icside.o
++obj-$(CONFIG_PATA_RB153_CF) += pata_rb153_cf.o
+ # Should be last but two libata driver
+ obj-$(CONFIG_PATA_ACPI) += pata_acpi.o
+ # Should be last but one libata driver
+--- a/drivers/ata/Kconfig
++++ b/drivers/ata/Kconfig
+@@ -566,6 +566,15 @@
+
+ If unsure, say N.
+
++config PATA_RB153_CF
++ tristate "RouterBOARD 153 Compact Flash support"
++ depends on MIPS_ADM5120
++ help
++ This option enables support for a Compact Flash connected on
++ the RouterBOARD 153.
++
++ If unsure, say N.
++
+ config PATA_RB532
+ tristate "RouterBoard 532 PATA CompactFlash support"
+ depends on MIKROTIK_RB532
--- /dev/null
+--- a/arch/mips/kernel/head.S
++++ b/arch/mips/kernel/head.S
+@@ -126,7 +126,12 @@
+ /*
+ * Reserved space for exception handlers.
+ * Necessary for machines which link their kernels at KSEG0.
++ * Use as temporary storage for the kernel command line, so that it
++ * can be updated easily without having to relink the kernel.
+ */
++
++EXPORT(_image_cmdline)
++ .ascii "CMDLINE:"
+ .fill 0x400
+ #endif
+
--- /dev/null
+--- a/drivers/serial/amba-pl010.c
++++ b/drivers/serial/amba-pl010.c
+@@ -52,11 +52,10 @@
+
+ #include <asm/io.h>
+
+-#define UART_NR 8
+-
+ #define SERIAL_AMBA_MAJOR 204
+ #define SERIAL_AMBA_MINOR 16
+-#define SERIAL_AMBA_NR UART_NR
++#define SERIAL_AMBA_NR CONFIG_SERIAL_AMBA_PL010_NUMPORTS
++#define SERIAL_AMBA_NAME CONFIG_SERIAL_AMBA_PL010_PORTNAME
+
+ #define AMBA_ISR_PASS_LIMIT 256
+
+@@ -82,9 +81,9 @@
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int cr;
+
+- cr = readb(uap->port.membase + UART010_CR);
++ cr = __raw_readl(uap->port.membase + UART010_CR);
+ cr &= ~UART010_CR_TIE;
+- writel(cr, uap->port.membase + UART010_CR);
++ __raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+
+ static void pl010_start_tx(struct uart_port *port)
+@@ -92,9 +91,9 @@
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int cr;
+
+- cr = readb(uap->port.membase + UART010_CR);
++ cr = __raw_readl(uap->port.membase + UART010_CR);
+ cr |= UART010_CR_TIE;
+- writel(cr, uap->port.membase + UART010_CR);
++ __raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+
+ static void pl010_stop_rx(struct uart_port *port)
+@@ -102,9 +101,9 @@
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int cr;
+
+- cr = readb(uap->port.membase + UART010_CR);
++ cr = __raw_readl(uap->port.membase + UART010_CR);
+ cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
+- writel(cr, uap->port.membase + UART010_CR);
++ __raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+
+ static void pl010_enable_ms(struct uart_port *port)
+@@ -112,9 +111,9 @@
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int cr;
+
+- cr = readb(uap->port.membase + UART010_CR);
++ cr = __raw_readl(uap->port.membase + UART010_CR);
+ cr |= UART010_CR_MSIE;
+- writel(cr, uap->port.membase + UART010_CR);
++ __raw_writel(cr, uap->port.membase + UART010_CR);
+ }
+
+ static void pl010_rx_chars(struct uart_amba_port *uap)
+@@ -122,9 +121,9 @@
+ struct tty_struct *tty = uap->port.info->tty;
+ unsigned int status, ch, flag, rsr, max_count = 256;
+
+- status = readb(uap->port.membase + UART01x_FR);
++ status = __raw_readl(uap->port.membase + UART01x_FR);
+ while (UART_RX_DATA(status) && max_count--) {
+- ch = readb(uap->port.membase + UART01x_DR);
++ ch = __raw_readl(uap->port.membase + UART01x_DR);
+ flag = TTY_NORMAL;
+
+ uap->port.icount.rx++;
+@@ -133,9 +132,9 @@
+ * Note that the error handling code is
+ * out of the main execution path
+ */
+- rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
++ rsr = __raw_readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
+ if (unlikely(rsr & UART01x_RSR_ANY)) {
+- writel(0, uap->port.membase + UART01x_ECR);
++ __raw_writel(0, uap->port.membase + UART01x_ECR);
+
+ if (rsr & UART01x_RSR_BE) {
+ rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
+@@ -165,7 +164,7 @@
+ uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
+
+ ignore_char:
+- status = readb(uap->port.membase + UART01x_FR);
++ status = __raw_readl(uap->port.membase + UART01x_FR);
+ }
+ spin_unlock(&uap->port.lock);
+ tty_flip_buffer_push(tty);
+@@ -178,7 +177,7 @@
+ int count;
+
+ if (uap->port.x_char) {
+- writel(uap->port.x_char, uap->port.membase + UART01x_DR);
++ __raw_writel(uap->port.x_char, uap->port.membase + UART01x_DR);
+ uap->port.icount.tx++;
+ uap->port.x_char = 0;
+ return;
+@@ -190,7 +189,7 @@
+
+ count = uap->port.fifosize >> 1;
+ do {
+- writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
++ __raw_writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ uap->port.icount.tx++;
+ if (uart_circ_empty(xmit))
+@@ -208,9 +207,9 @@
+ {
+ unsigned int status, delta;
+
+- writel(0, uap->port.membase + UART010_ICR);
++ __raw_writel(0, uap->port.membase + UART010_ICR);
+
+- status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
++ status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+
+ delta = status ^ uap->old_status;
+ uap->old_status = status;
+@@ -238,7 +237,7 @@
+
+ spin_lock(&uap->port.lock);
+
+- status = readb(uap->port.membase + UART010_IIR);
++ status = __raw_readl(uap->port.membase + UART010_IIR);
+ if (status) {
+ do {
+ if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
+@@ -251,7 +250,7 @@
+ if (pass_counter-- == 0)
+ break;
+
+- status = readb(uap->port.membase + UART010_IIR);
++ status = __raw_readl(uap->port.membase + UART010_IIR);
+ } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
+ UART010_IIR_TIS));
+ handled = 1;
+@@ -265,7 +264,7 @@
+ static unsigned int pl010_tx_empty(struct uart_port *port)
+ {
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+- unsigned int status = readb(uap->port.membase + UART01x_FR);
++ unsigned int status = __raw_readl(uap->port.membase + UART01x_FR);
+ return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
+ }
+
+@@ -275,7 +274,7 @@
+ unsigned int result = 0;
+ unsigned int status;
+
+- status = readb(uap->port.membase + UART01x_FR);
++ status = __raw_readl(uap->port.membase + UART01x_FR);
+ if (status & UART01x_FR_DCD)
+ result |= TIOCM_CAR;
+ if (status & UART01x_FR_DSR)
+@@ -301,12 +300,12 @@
+ unsigned int lcr_h;
+
+ spin_lock_irqsave(&uap->port.lock, flags);
+- lcr_h = readb(uap->port.membase + UART010_LCRH);
++ lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
+ if (break_state == -1)
+ lcr_h |= UART01x_LCRH_BRK;
+ else
+ lcr_h &= ~UART01x_LCRH_BRK;
+- writel(lcr_h, uap->port.membase + UART010_LCRH);
++ __raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
+ spin_unlock_irqrestore(&uap->port.lock, flags);
+ }
+
+@@ -334,12 +333,12 @@
+ /*
+ * initialise the old status of the modem signals
+ */
+- uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
++ uap->old_status = __raw_readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+
+ /*
+ * Finally, enable interrupts
+ */
+- writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
++ __raw_writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
+ uap->port.membase + UART010_CR);
+
+ return 0;
+@@ -362,10 +361,10 @@
+ /*
+ * disable all interrupts, disable the port
+ */
+- writel(0, uap->port.membase + UART010_CR);
++ __raw_writel(0, uap->port.membase + UART010_CR);
+
+ /* disable break condition and fifos */
+- writel(readb(uap->port.membase + UART010_LCRH) &
++ __raw_writel(__raw_readl(uap->port.membase + UART010_LCRH) &
+ ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
+ uap->port.membase + UART010_LCRH);
+
+@@ -387,7 +386,7 @@
+ /*
+ * Ask the core to calculate the divisor for us.
+ */
+- baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
++ baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
+ quot = uart_get_divisor(port, baud);
+
+ switch (termios->c_cflag & CSIZE) {
+@@ -450,25 +449,25 @@
+ uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
+
+ /* first, disable everything */
+- old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
++ old_cr = __raw_readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
+
+ if (UART_ENABLE_MS(port, termios->c_cflag))
+ old_cr |= UART010_CR_MSIE;
+
+- writel(0, uap->port.membase + UART010_CR);
++ __raw_writel(0, uap->port.membase + UART010_CR);
+
+ /* Set baud rate */
+ quot -= 1;
+- writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
+- writel(quot & 0xff, uap->port.membase + UART010_LCRL);
++ __raw_writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
++ __raw_writel(quot & 0xff, uap->port.membase + UART010_LCRL);
+
+ /*
+ * ----------v----------v----------v----------v-----
+ * NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
+ * ----------^----------^----------^----------^-----
+ */
+- writel(lcr_h, uap->port.membase + UART010_LCRH);
+- writel(old_cr, uap->port.membase + UART010_CR);
++ __raw_writel(lcr_h, uap->port.membase + UART010_LCRH);
++ __raw_writel(old_cr, uap->port.membase + UART010_CR);
+
+ spin_unlock_irqrestore(&uap->port.lock, flags);
+ }
+@@ -540,7 +539,7 @@
+ .verify_port = pl010_verify_port,
+ };
+
+-static struct uart_amba_port *amba_ports[UART_NR];
++static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR];
+
+ #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE
+
+@@ -550,10 +549,10 @@
+ unsigned int status;
+
+ do {
+- status = readb(uap->port.membase + UART01x_FR);
++ status = __raw_readl(uap->port.membase + UART01x_FR);
+ barrier();
+ } while (!UART_TX_READY(status));
+- writel(ch, uap->port.membase + UART01x_DR);
++ __raw_writel(ch, uap->port.membase + UART01x_DR);
+ }
+
+ static void
+@@ -567,8 +566,8 @@
+ /*
+ * First save the CR then disable the interrupts
+ */
+- old_cr = readb(uap->port.membase + UART010_CR);
+- writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
++ old_cr = __raw_readl(uap->port.membase + UART010_CR);
++ __raw_writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
+
+ uart_console_write(&uap->port, s, count, pl010_console_putchar);
+
+@@ -577,10 +576,10 @@
+ * and restore the TCR
+ */
+ do {
+- status = readb(uap->port.membase + UART01x_FR);
++ status = __raw_readl(uap->port.membase + UART01x_FR);
+ barrier();
+ } while (status & UART01x_FR_BUSY);
+- writel(old_cr, uap->port.membase + UART010_CR);
++ __raw_writel(old_cr, uap->port.membase + UART010_CR);
+
+ clk_disable(uap->clk);
+ }
+@@ -589,9 +588,9 @@
+ pl010_console_get_options(struct uart_amba_port *uap, int *baud,
+ int *parity, int *bits)
+ {
+- if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
++ if (__raw_readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
+ unsigned int lcr_h, quot;
+- lcr_h = readb(uap->port.membase + UART010_LCRH);
++ lcr_h = __raw_readl(uap->port.membase + UART010_LCRH);
+
+ *parity = 'n';
+ if (lcr_h & UART01x_LCRH_PEN) {
+@@ -606,8 +605,8 @@
+ else
+ *bits = 8;
+
+- quot = readb(uap->port.membase + UART010_LCRL) |
+- readb(uap->port.membase + UART010_LCRM) << 8;
++ quot = __raw_readl(uap->port.membase + UART010_LCRL) |
++ __raw_readl(uap->port.membase + UART010_LCRM) << 8;
+ *baud = uap->port.uartclk / (16 * (quot + 1));
+ }
+ }
+@@ -625,7 +624,7 @@
+ * if so, search for the first available port that does have
+ * console support.
+ */
+- if (co->index >= UART_NR)
++ if (co->index >= SERIAL_AMBA_NR)
+ co->index = 0;
+ uap = amba_ports[co->index];
+ if (!uap)
+@@ -643,7 +642,7 @@
+
+ static struct uart_driver amba_reg;
+ static struct console amba_console = {
+- .name = "ttyAM",
++ .name = SERIAL_AMBA_NAME,
+ .write = pl010_console_write,
+ .device = uart_console_device,
+ .setup = pl010_console_setup,
+@@ -659,11 +658,11 @@
+
+ static struct uart_driver amba_reg = {
+ .owner = THIS_MODULE,
+- .driver_name = "ttyAM",
+- .dev_name = "ttyAM",
++ .driver_name = SERIAL_AMBA_NAME,
++ .dev_name = SERIAL_AMBA_NAME,
+ .major = SERIAL_AMBA_MAJOR,
+ .minor = SERIAL_AMBA_MINOR,
+- .nr = UART_NR,
++ .nr = SERIAL_AMBA_NR,
+ .cons = AMBA_CONSOLE,
+ };
+
+--- a/drivers/serial/Kconfig
++++ b/drivers/serial/Kconfig
+@@ -287,10 +287,25 @@
+ help
+ This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have
+ an Integrator/AP or Integrator/PP2 platform, or if you have a
+- Cirrus Logic EP93xx CPU, say Y or M here.
++ Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here.
+
+ If unsure, say N.
+
++config SERIAL_AMBA_PL010_NUMPORTS
++ int "Maximum number of AMBA PL010 serial ports"
++ depends on SERIAL_AMBA_PL010
++ default "8"
++ ---help---
++ Set this to the number of serial ports you want the AMBA PL010 driver
++ to support.
++
++config SERIAL_AMBA_PL010_PORTNAME
++ string "Name of the AMBA PL010 serial ports"
++ depends on SERIAL_AMBA_PL010
++ default "ttyAM"
++ ---help---
++ ::: To be written :::
++
+ config SERIAL_AMBA_PL010_CONSOLE
+ bool "Support for console on AMBA serial port"
+ depends on SERIAL_AMBA_PL010=y
--- /dev/null
+--- a/drivers/amba/bus.c
++++ b/drivers/amba/bus.c
+@@ -17,6 +17,10 @@
+ #include <asm/io.h>
+ #include <asm/sizes.h>
+
++#ifndef NO_IRQ
++#define NO_IRQ (-1)
++#endif
++
+ #define to_amba_device(d) container_of(d, struct amba_device, dev)
+ #define to_amba_driver(d) container_of(d, struct amba_driver, drv)
+
--- /dev/null
+--- a/drivers/pci/Kconfig
++++ b/drivers/pci/Kconfig
+@@ -42,6 +42,12 @@
+
+ When in doubt, say N.
+
++config PCI_DISABLE_COMMON_QUIRKS
++ bool "PCI disable common quirks"
++ depends on PCI
++ help
++ If you don't know what to do here, say N.
++
+ config HT_IRQ
+ bool "Interrupts on hypertransport devices"
+ default y
+--- a/drivers/pci/quirks.c
++++ b/drivers/pci/quirks.c
+@@ -24,6 +24,7 @@
+ #include <linux/kallsyms.h>
+ #include "pci.h"
+
++#ifndef CONFIG_PCI_DISABLE_COMMON_QUIRKS
+ /* The Mellanox Tavor device gives false positive parity errors
+ * Mark this device with a broken_parity_status, to allow
+ * PCI scanning code to "skip" this now blacklisted device.
+@@ -1495,6 +1496,7 @@
+ }
+ }
+ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, fixup_rev1_53c810);
++#endif /* !CONFIG_PCI_DISABLE_COMMON_QUIRKS */
+
+ static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end)
+ {
+@@ -1561,6 +1563,7 @@
+ }
+ EXPORT_SYMBOL(pci_fixup_device);
+
++#ifndef CONFIG_PCI_DISABLE_COMMON_QUIRKS
+ /* Enable 1k I/O space granularity on the Intel P64H2 */
+ static void __devinit quirk_p64h2_1k_io(struct pci_dev *dev)
+ {
+@@ -1929,3 +1932,4 @@
+ quirk_msi_intx_disable_bug);
+
+ #endif /* CONFIG_PCI_MSI */
++#endif /* !CONFIG_PCI_DISABLE_COMMON_QUIRKS */
--- /dev/null
+--- a/drivers/leds/leds-gpio.c
++++ b/drivers/leds/leds-gpio.c
+@@ -43,13 +43,17 @@
+ container_of(led_cdev, struct gpio_led_data, cdev);
+ int level;
+
+- if (value == LED_OFF)
+- level = 0;
+- else
+- level = 1;
+-
+- if (led_dat->active_low)
+- level = !level;
++ switch (value) {
++ case LED_OFF:
++ level = led_dat->active_low ? 1 : 0;
++ break;
++ case LED_FULL:
++ level = led_dat->active_low ? 0 : 1;
++ break;
++ default:
++ level = value;
++ break;
++ }
+
+ /* Setting GPIOs with I2C/etc requires a task context, and we don't
+ * seem to have a reliable way to know if we're already in one; so
--- /dev/null
+--- a/drivers/watchdog/Kconfig
++++ b/drivers/watchdog/Kconfig
+@@ -632,6 +632,18 @@
+
+ # MIPS Architecture
+
++config ADM5120_WDT
++ tristate "Infineon ADM5120 SoC hardware watchdog"
++ depends on WATCHDOG && MIPS_ADM5120
++ help
++ This is a driver for hardware watchdog integrated in Infineon
++ ADM5120 SoC. This watchdog simply watches your kernel to make sure
++ it doesn't freeze, and if it does, it reboots your computer after a
++ certain amount of time.
++
++ To compile this driver as a module, choose M here: the module will be
++ called adm5120_wdt.
++
+ config INDYDOG
+ tristate "Indy/I2 Hardware Watchdog"
+ depends on SGI_HAS_INDYDOG
+--- a/drivers/watchdog/Makefile
++++ b/drivers/watchdog/Makefile
+@@ -91,6 +91,7 @@
+ # M68KNOMMU Architecture
+
+ # MIPS Architecture
++obj-$(CONFIG_ADM5120_WDT) += adm5120_wdt.o
+ obj-$(CONFIG_INDYDOG) += indydog.o
+ obj-$(CONFIG_WDT_MTX1) += mtx-1_wdt.o
+ obj-$(CONFIG_WDT_RM9K_GPI) += rm9k_wdt.o
--- /dev/null
+CONFIG_32BIT=y
+# CONFIG_64BIT is not set
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_ADM5120_CPU_OVERRIDES=y
+CONFIG_ADM5120_WDT=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_ARCH_SUPPORTS_OPROFILE=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARM_AMBA=y
+CONFIG_BASE_SMALL=0
+CONFIG_BAYCOM_SER_FDX=m
+CONFIG_BAYCOM_SER_HDX=m
+# CONFIG_BCM47XX is not set
+CONFIG_BINFMT_MISC=m
+CONFIG_BITREVERSE=y
+CONFIG_CEVT_R4K=y
+CONFIG_CIFS_DEBUG2=y
+CONFIG_CIFS_EXPERIMENTAL=y
+CONFIG_CIFS_STATS2=y
+CONFIG_CIFS_WEAK_PW_HASH=y
+CONFIG_CIFS_XATTR=y
+CONFIG_CLASSIC_RCU=y
+CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2 init=/etc/preinit"
+CONFIG_CPU_BIG_ENDIAN=y
+CONFIG_CPU_HAS_LLSC=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_SYNC=y
+# CONFIG_CPU_LITTLE_ENDIAN is not set
+# CONFIG_CPU_LOONGSON2 is not set
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPS32_R1=y
+# CONFIG_CPU_MIPS32_R2 is not set
+# CONFIG_CPU_MIPS64_R1 is not set
+# CONFIG_CPU_MIPS64_R2 is not set
+CONFIG_CPU_MIPSR1=y
+# CONFIG_CPU_NEVADA is not set
+# CONFIG_CPU_R10000 is not set
+# CONFIG_CPU_R3000 is not set
+# CONFIG_CPU_R4300 is not set
+# CONFIG_CPU_R4X00 is not set
+# CONFIG_CPU_R5000 is not set
+# CONFIG_CPU_R5432 is not set
+# CONFIG_CPU_R6000 is not set
+# CONFIG_CPU_R8000 is not set
+# CONFIG_CPU_RM7000 is not set
+# CONFIG_CPU_RM9000 is not set
+# CONFIG_CPU_SB1 is not set
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+# CONFIG_CPU_TX39XX is not set
+# CONFIG_CPU_TX49XX is not set
+# CONFIG_CPU_VR41XX is not set
+CONFIG_CRYPTO_AEAD=m
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_GF128MUL=m
+CONFIG_CSRC_R4K=y
+CONFIG_DEVPORT=y
+# CONFIG_DM9000 is not set
+CONFIG_DMA_NEED_PCI_MAP_STATE=y
+CONFIG_DMA_NONCOHERENT=y
+# CONFIG_E1000E_ENABLED is not set
+CONFIG_EARLY_PRINTK=y
+CONFIG_ELF_CORE=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+CONFIG_EXT3_FS_XATTR=y
+CONFIG_FS_MBCACHE=m
+CONFIG_FS_POSIX_ACL=y
+CONFIG_GENERIC_ACL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_GPIO=y
+# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+# CONFIG_HAVE_DMA_ATTRS is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HID=m
+CONFIG_HID_SUPPORT=y
+CONFIG_HW_HAS_PCI=y
+CONFIG_HW_RANDOM=y
+CONFIG_HZ=250
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_I2C is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IDE is not set
+CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_INPUT=m
+# CONFIG_INPUT_EVDEV is not set
+CONFIG_IPV6_MIP6=m
+# CONFIG_IPV6_MROUTE is not set
+CONFIG_IPV6_NDISC_NODETYPE=y
+CONFIG_IPV6_PRIVACY=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IRQ_CPU=y
+# CONFIG_IWLWIFI_LEDS is not set
+# CONFIG_JOLIET is not set
+CONFIG_LEDS_ADM5120=m
+# CONFIG_LEDS_ADM5120_DIAG is not set
+# CONFIG_LEDS_ADM5120_EXPERIMENTAL is not set
+# CONFIG_LEDS_ALIX is not set
+CONFIG_LEDS_GPIO=m
+CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_LEMOTE_FULONG is not set
+CONFIG_LZO_COMPRESS=m
+CONFIG_LZO_DECOMPRESS=m
+# CONFIG_MACH_ALCHEMY is not set
+# CONFIG_MACH_DECSTATION is not set
+# CONFIG_MACH_JAZZ is not set
+# CONFIG_MACH_VR41XX is not set
+# CONFIG_MEDIA_ATTACH is not set
+# CONFIG_MEMSTICK is not set
+CONFIG_MII=m
+# CONFIG_MINIX_FS is not set
+CONFIG_MIPS=y
+CONFIG_MIPS_ADM5120=y
+CONFIG_MIPS_ADM5120_ENET=y
+# CONFIG_MIPS_ATLAS is not set
+# CONFIG_MIPS_COBALT is not set
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+# CONFIG_MIPS_MALTA is not set
+CONFIG_MIPS_MT_DISABLED=y
+# CONFIG_MIPS_MT_SMP is not set
+# CONFIG_MIPS_MT_SMTC is not set
+# CONFIG_MIPS_SEAD is not set
+# CONFIG_MIPS_SIM is not set
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MTD=y
+# CONFIG_MTD_ABSENT is not set
+CONFIG_MTD_ADM5120=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_MTD_BLOCK2MTD=y
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_JEDECPROBE is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_MYLOADER_PARTS is not set
+# CONFIG_MTD_ONENAND is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_PCI is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_PLATRAM is not set
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_SLRAM is not set
+CONFIG_MTD_TRXSPLIT=y
+# CONFIG_NET_PCI is not set
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NO_IOPORT is not set
+# CONFIG_OCF_OCF is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
+# CONFIG_PAGE_SIZE_16KB is not set
+CONFIG_PAGE_SIZE_4KB=y
+# CONFIG_PAGE_SIZE_64KB is not set
+# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_PCI=y
+# CONFIG_PCIPCWATCHDOG is not set
+CONFIG_PCI_ADM5120=y
+CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCSPKR_PLATFORM is not set
+# CONFIG_PMC_MSP is not set
+# CONFIG_PMC_YOSEMITE is not set
+# CONFIG_PNX8550_JBS is not set
+# CONFIG_PNX8550_STB810 is not set
+CONFIG_RFKILL_LEDS=y
+CONFIG_RTC_LIB=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_SCSI_WAIT_SCAN=m
+# CONFIG_SERIAL_8250 is not set
+CONFIG_SERIAL_AMBA_PL010=y
+CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
+CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
+CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS"
+# CONFIG_SERIAL_AMBA_PL011 is not set
+CONFIG_SERIO=y
+# CONFIG_SERIO_AMBAKMI is not set
+# CONFIG_SERIO_I8042 is not set
+# CONFIG_SERIO_LIBPS2 is not set
+# CONFIG_SERIO_PCIPS2 is not set
+# CONFIG_SERIO_RAW is not set
+CONFIG_SERIO_SERPORT=y
+# CONFIG_SGI_IP22 is not set
+# CONFIG_SGI_IP27 is not set
+# CONFIG_SGI_IP28 is not set
+# CONFIG_SGI_IP32 is not set
+# CONFIG_SIBYTE_BIGSUR is not set
+# CONFIG_SIBYTE_CARMEL is not set
+# CONFIG_SIBYTE_CRHINE is not set
+# CONFIG_SIBYTE_CRHONE is not set
+# CONFIG_SIBYTE_LITTLESUR is not set
+# CONFIG_SIBYTE_RHONE is not set
+# CONFIG_SIBYTE_SENTOSA is not set
+# CONFIG_SIBYTE_SWARM is not set
+CONFIG_SLABINFO=y
+# CONFIG_SND_AW2 is not set
+CONFIG_SOFT_WATCHDOG=m
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SSB_POSSIBLE=y
+CONFIG_SWAP_IO_SPACE=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
+CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+CONFIG_TICK_ONESHOT=y
+CONFIG_TMPFS_POSIX_ACL=y
+# CONFIG_TOSHIBA_JMR3927 is not set
+# CONFIG_TOSHIBA_RBTX4927 is not set
+# CONFIG_TOSHIBA_RBTX4938 is not set
+CONFIG_TRAD_SIGNALS=y
+CONFIG_USB=m
+# CONFIG_USBPCWATCHDOG is not set
+CONFIG_USB_ADM5120_HCD=m
+# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_DEBUG=y
+CONFIG_USB_EHCI_HCD=m
+CONFIG_USB_HSO=m
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_HCD=m
+# CONFIG_USB_R8A66597_HCD is not set
+CONFIG_USB_SERIAL_MOTOROLA=m
+CONFIG_USB_SERIAL_SPCP8X5=m
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_UHCI_HCD is not set
+# CONFIG_USB_WDM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_ALLOW_V4L1 is not set
+CONFIG_VIDEO_MEDIA=m
+CONFIG_VIDEO_V4L2=m
+CONFIG_VIDEO_V4L2_COMMON=m
+CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_XFS_DEBUG is not set
+CONFIG_ZONE_DMA_FLAG=0
--- /dev/null
+CONFIG_32BIT=y
+# CONFIG_64BIT is not set
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_ADM5120_CPU_OVERRIDES=y
+CONFIG_ADM5120_WDT=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_ARCH_POPULATES_NODE_MAP=y
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+CONFIG_ARCH_SUPPORTS_OPROFILE=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARM_AMBA=y
+CONFIG_BASE_SMALL=0
+CONFIG_BAYCOM_SER_FDX=m
+CONFIG_BAYCOM_SER_HDX=m
+# CONFIG_BCM47XX is not set
+CONFIG_BINFMT_MISC=m
+CONFIG_BITREVERSE=y
+CONFIG_CEVT_R4K=y
+CONFIG_CIFS_DEBUG2=y
+CONFIG_CIFS_EXPERIMENTAL=y
+CONFIG_CIFS_STATS2=y
+CONFIG_CIFS_WEAK_PW_HASH=y
+CONFIG_CIFS_XATTR=y
+CONFIG_CLASSIC_RCU=y
+CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2 init=/etc/preinit"
+# CONFIG_CPU_BIG_ENDIAN is not set
+CONFIG_CPU_HAS_LLSC=y
+CONFIG_CPU_HAS_PREFETCH=y
+CONFIG_CPU_HAS_SYNC=y
+CONFIG_CPU_LITTLE_ENDIAN=y
+# CONFIG_CPU_LOONGSON2 is not set
+CONFIG_CPU_MIPS32=y
+CONFIG_CPU_MIPS32_R1=y
+# CONFIG_CPU_MIPS32_R2 is not set
+# CONFIG_CPU_MIPS64_R1 is not set
+# CONFIG_CPU_MIPS64_R2 is not set
+CONFIG_CPU_MIPSR1=y
+# CONFIG_CPU_NEVADA is not set
+# CONFIG_CPU_R10000 is not set
+# CONFIG_CPU_R3000 is not set
+# CONFIG_CPU_R4300 is not set
+# CONFIG_CPU_R4X00 is not set
+# CONFIG_CPU_R5000 is not set
+# CONFIG_CPU_R5432 is not set
+# CONFIG_CPU_R6000 is not set
+# CONFIG_CPU_R8000 is not set
+# CONFIG_CPU_RM7000 is not set
+# CONFIG_CPU_RM9000 is not set
+# CONFIG_CPU_SB1 is not set
+CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
+CONFIG_CPU_SUPPORTS_HIGHMEM=y
+# CONFIG_CPU_TX39XX is not set
+# CONFIG_CPU_TX49XX is not set
+# CONFIG_CPU_VR41XX is not set
+CONFIG_CRYPTO_AEAD=m
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_GF128MUL=m
+CONFIG_CSRC_R4K=y
+CONFIG_DEVPORT=y
+# CONFIG_DM9000 is not set
+CONFIG_DMA_NEED_PCI_MAP_STATE=y
+CONFIG_DMA_NONCOHERENT=y
+# CONFIG_E1000E_ENABLED is not set
+CONFIG_EARLY_PRINTK=y
+CONFIG_ELF_CORE=y
+# CONFIG_EXT3_FS_POSIX_ACL is not set
+# CONFIG_EXT3_FS_SECURITY is not set
+CONFIG_EXT3_FS_XATTR=y
+CONFIG_FS_MBCACHE=m
+CONFIG_FS_POSIX_ACL=y
+CONFIG_GENERIC_ACL=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
+CONFIG_GENERIC_CMOS_UPDATE=y
+# CONFIG_GENERIC_FIND_FIRST_BIT is not set
+CONFIG_GENERIC_FIND_NEXT_BIT=y
+CONFIG_GENERIC_GPIO=y
+# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT=y
+# CONFIG_HAVE_DMA_ATTRS is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_HAVE_KPROBES is not set
+# CONFIG_HAVE_KRETPROBES is not set
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HID=m
+CONFIG_HID_SUPPORT=y
+CONFIG_HW_HAS_PCI=y
+CONFIG_HW_RANDOM=y
+CONFIG_HZ=250
+# CONFIG_HZ_100 is not set
+CONFIG_HZ_250=y
+# CONFIG_I2C is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IDE is not set
+CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+CONFIG_INPUT=m
+# CONFIG_INPUT_EVDEV is not set
+CONFIG_IPV6_MIP6=m
+# CONFIG_IPV6_MROUTE is not set
+CONFIG_IPV6_NDISC_NODETYPE=y
+CONFIG_IPV6_PRIVACY=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_TUNNEL=m
+CONFIG_IP_NF_TARGET_CLUSTERIP=m
+CONFIG_IRQ_CPU=y
+# CONFIG_IWLWIFI_LEDS is not set
+# CONFIG_JOLIET is not set
+CONFIG_LEDS_ADM5120=m
+# CONFIG_LEDS_ADM5120_DIAG is not set
+# CONFIG_LEDS_ADM5120_EXPERIMENTAL is not set
+# CONFIG_LEDS_ALIX is not set
+CONFIG_LEDS_GPIO=m
+CONFIG_LEDS_TRIGGER_ADM5120_SWITCH=m
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=256
+# CONFIG_LEMOTE_FULONG is not set
+CONFIG_LZO_COMPRESS=m
+CONFIG_LZO_DECOMPRESS=m
+# CONFIG_MACH_ALCHEMY is not set
+# CONFIG_MACH_DECSTATION is not set
+# CONFIG_MACH_JAZZ is not set
+# CONFIG_MACH_VR41XX is not set
+# CONFIG_MEDIA_ATTACH is not set
+# CONFIG_MEMSTICK is not set
+CONFIG_MII=m
+# CONFIG_MINIX_FS is not set
+CONFIG_MIPS=y
+CONFIG_MIPS_ADM5120=y
+CONFIG_MIPS_ADM5120_ENET=y
+# CONFIG_MIPS_ATLAS is not set
+# CONFIG_MIPS_COBALT is not set
+CONFIG_MIPS_L1_CACHE_SHIFT=5
+# CONFIG_MIPS_MALTA is not set
+CONFIG_MIPS_MT_DISABLED=y
+# CONFIG_MIPS_MT_SMP is not set
+# CONFIG_MIPS_MT_SMTC is not set
+# CONFIG_MIPS_SEAD is not set
+# CONFIG_MIPS_SIM is not set
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MTD=y
+# CONFIG_MTD_ABSENT is not set
+CONFIG_MTD_ADM5120=y
+# CONFIG_MTD_ALAUDA is not set
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+# CONFIG_MTD_BLOCK2MTD is not set
+CONFIG_MTD_CFI=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+# CONFIG_MTD_CFI_STAA is not set
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
+# CONFIG_MTD_CONCAT is not set
+# CONFIG_MTD_DEBUG is not set
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_GEN_PROBE=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MTDRAM is not set
+CONFIG_MTD_MYLOADER_PARTS=y
+CONFIG_MTD_NAND=y
+# CONFIG_MTD_NAND_CAFE is not set
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_ECC_SMC is not set
+CONFIG_MTD_NAND_IDS=y
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+CONFIG_MTD_NAND_PLATFORM=y
+# CONFIG_MTD_NAND_VERIFY_WRITE is not set
+# CONFIG_MTD_ONENAND is not set
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_PCI is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_PLATRAM is not set
+# CONFIG_MTD_PMC551 is not set
+# CONFIG_MTD_RAM is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+# CONFIG_MTD_ROM is not set
+# CONFIG_MTD_SLRAM is not set
+CONFIG_MTD_TRXSPLIT=y
+# CONFIG_NETFILTER_XT_TARGET_TARPIT is not set
+# CONFIG_NET_PCI is not set
+# CONFIG_NET_PKTGEN is not set
+# CONFIG_NET_VENDOR_3COM is not set
+# CONFIG_NO_IOPORT is not set
+# CONFIG_OCF_OCF is not set
+CONFIG_PAGEFLAGS_EXTENDED=y
+# CONFIG_PAGE_SIZE_16KB is not set
+CONFIG_PAGE_SIZE_4KB=y
+# CONFIG_PAGE_SIZE_64KB is not set
+# CONFIG_PAGE_SIZE_8KB is not set
+# CONFIG_PARTITION_ADVANCED is not set
+CONFIG_PCI=y
+# CONFIG_PCIPCWATCHDOG is not set
+CONFIG_PCI_ADM5120=y
+CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
+CONFIG_PCI_DOMAINS=y
+# CONFIG_PCSPKR_PLATFORM is not set
+# CONFIG_PMC_MSP is not set
+# CONFIG_PMC_YOSEMITE is not set
+# CONFIG_PNX8550_JBS is not set
+# CONFIG_PNX8550_STB810 is not set
+CONFIG_RFKILL_LEDS=y
+CONFIG_RTC_LIB=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y
+CONFIG_SCSI_WAIT_SCAN=m
+# CONFIG_SERIAL_8250 is not set
+CONFIG_SERIAL_AMBA_PL010=y
+CONFIG_SERIAL_AMBA_PL010_CONSOLE=y
+CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2
+CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS"
+# CONFIG_SERIAL_AMBA_PL011 is not set
+CONFIG_SERIO=y
+# CONFIG_SERIO_AMBAKMI is not set
+# CONFIG_SERIO_I8042 is not set
+# CONFIG_SERIO_LIBPS2 is not set
+# CONFIG_SERIO_PCIPS2 is not set
+# CONFIG_SERIO_RAW is not set
+CONFIG_SERIO_SERPORT=y
+# CONFIG_SGI_IP22 is not set
+# CONFIG_SGI_IP27 is not set
+# CONFIG_SGI_IP28 is not set
+# CONFIG_SGI_IP32 is not set
+# CONFIG_SIBYTE_BIGSUR is not set
+# CONFIG_SIBYTE_CARMEL is not set
+# CONFIG_SIBYTE_CRHINE is not set
+# CONFIG_SIBYTE_CRHONE is not set
+# CONFIG_SIBYTE_LITTLESUR is not set
+# CONFIG_SIBYTE_RHONE is not set
+# CONFIG_SIBYTE_SENTOSA is not set
+# CONFIG_SIBYTE_SWARM is not set
+CONFIG_SLABINFO=y
+# CONFIG_SND_AW2 is not set
+CONFIG_SOFT_WATCHDOG=m
+# CONFIG_SPARSEMEM_STATIC is not set
+# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set
+CONFIG_SSB_POSSIBLE=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_SYS_HAS_CPU_MIPS32_R1=y
+CONFIG_SYS_HAS_EARLY_PRINTK=y
+CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
+CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
+CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
+CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
+# CONFIG_THERMAL is not set
+# CONFIG_THERMAL_HWMON is not set
+CONFIG_TICK_ONESHOT=y
+CONFIG_TMPFS_POSIX_ACL=y
+# CONFIG_TOSHIBA_JMR3927 is not set
+# CONFIG_TOSHIBA_RBTX4927 is not set
+# CONFIG_TOSHIBA_RBTX4938 is not set
+CONFIG_TRAD_SIGNALS=y
+CONFIG_USB=m
+# CONFIG_USBPCWATCHDOG is not set
+CONFIG_USB_ADM5120_HCD=m
+# CONFIG_USB_C67X00_HCD is not set
+CONFIG_USB_DEBUG=y
+CONFIG_USB_EHCI_HCD=m
+CONFIG_USB_HSO=m
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_ISP1760_HCD is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_HCD=m
+# CONFIG_USB_R8A66597_HCD is not set
+CONFIG_USB_SERIAL_MOTOROLA=m
+CONFIG_USB_SERIAL_SPCP8X5=m
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+# CONFIG_USB_UHCI_HCD is not set
+# CONFIG_USB_WDM is not set
+# CONFIG_VGASTATE is not set
+# CONFIG_VIDEO_ALLOW_V4L1 is not set
+CONFIG_VIDEO_MEDIA=m
+CONFIG_VIDEO_V4L2=m
+CONFIG_VIDEO_V4L2_COMMON=m
+CONFIG_VM_EVENT_COUNTERS=y
+# CONFIG_XFS_DEBUG is not set
+CONFIG_YAFFS_9BYTE_TAGS=y
+# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set
+CONFIG_YAFFS_AUTO_YAFFS2=y
+CONFIG_YAFFS_CHECKPOINT_RESERVED_BLOCKS=0
+# CONFIG_YAFFS_DISABLE_LAZY_LOAD is not set
+# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set
+CONFIG_YAFFS_FS=y
+CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y
+CONFIG_YAFFS_YAFFS1=y
+CONFIG_YAFFS_YAFFS2=y
+CONFIG_ZONE_DMA_FLAG=0
projects / openwrt / svn-archive / openwrt.git / commitdiff