#include <mach/hardware.h>
#include <mach/dma.h>
-#include <mach/pxa-regs.h>
-
struct dma_channel {
char *name;
pxa_dma_prio prio;
#ifndef __ASM_ARCH_DMA_H
#define __ASM_ARCH_DMA_H
+#include <mach/hardware.h>
+
+/* DMA Controller Registers Definitions */
+#define DMAC_REGS_VIRT io_p2v(0x40000000)
+#define DMAC_REG(x) (*((volatile u32 *)(DMAC_REGS_VIRT + (x))))
+
+#define DCSR(n) DMAC_REG((n) << 2)
+#define DALGN DMAC_REG(0x00a0) /* DMA Alignment Register */
+#define DINT DMAC_REG(0x00f0) /* DMA Interrupt Register */
+#define DDADR(n) DMAC_REG(0x0200 + ((n) << 4))
+#define DSADR(n) DMAC_REG(0x0204 + ((n) << 4))
+#define DTADR(n) DMAC_REG(0x0208 + ((n) << 4))
+#define DCMD(n) DMAC_REG(0x020c + ((n) << 4))
+#define DRCMR(n) DMAC_REG((((n) < 64) ? 0x0100 : 0x1100) + \
+ (((n) & 0x3f) << 2))
+
+#define DCSR_RUN (1 << 31) /* Run Bit (read / write) */
+#define DCSR_NODESC (1 << 30) /* No-Descriptor Fetch (read / write) */
+#define DCSR_STOPIRQEN (1 << 29) /* Stop Interrupt Enable (read / write) */
+#define DCSR_REQPEND (1 << 8) /* Request Pending (read-only) */
+#define DCSR_STOPSTATE (1 << 3) /* Stop State (read-only) */
+#define DCSR_ENDINTR (1 << 2) /* End Interrupt (read / write) */
+#define DCSR_STARTINTR (1 << 1) /* Start Interrupt (read / write) */
+#define DCSR_BUSERR (1 << 0) /* Bus Error Interrupt (read / write) */
+
+#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
+#define DCSR_EORIRQEN (1 << 28) /* End of Receive Interrupt Enable (R/W) */
+#define DCSR_EORJMPEN (1 << 27) /* Jump to next descriptor on EOR */
+#define DCSR_EORSTOPEN (1 << 26) /* STOP on an EOR */
+#define DCSR_SETCMPST (1 << 25) /* Set Descriptor Compare Status */
+#define DCSR_CLRCMPST (1 << 24) /* Clear Descriptor Compare Status */
+#define DCSR_CMPST (1 << 10) /* The Descriptor Compare Status */
+#define DCSR_EORINTR (1 << 9) /* The end of Receive */
+#endif
+
+#define DRCMR_MAPVLD (1 << 7) /* Map Valid (read / write) */
+#define DRCMR_CHLNUM 0x1f /* mask for Channel Number (read / write) */
+
+#define DDADR_DESCADDR 0xfffffff0 /* Address of next descriptor (mask) */
+#define DDADR_STOP (1 << 0) /* Stop (read / write) */
+
+#define DCMD_INCSRCADDR (1 << 31) /* Source Address Increment Setting. */
+#define DCMD_INCTRGADDR (1 << 30) /* Target Address Increment Setting. */
+#define DCMD_FLOWSRC (1 << 29) /* Flow Control by the source. */
+#define DCMD_FLOWTRG (1 << 28) /* Flow Control by the target. */
+#define DCMD_STARTIRQEN (1 << 22) /* Start Interrupt Enable */
+#define DCMD_ENDIRQEN (1 << 21) /* End Interrupt Enable */
+#define DCMD_ENDIAN (1 << 18) /* Device Endian-ness. */
+#define DCMD_BURST8 (1 << 16) /* 8 byte burst */
+#define DCMD_BURST16 (2 << 16) /* 16 byte burst */
+#define DCMD_BURST32 (3 << 16) /* 32 byte burst */
+#define DCMD_WIDTH1 (1 << 14) /* 1 byte width */
+#define DCMD_WIDTH2 (2 << 14) /* 2 byte width (HalfWord) */
+#define DCMD_WIDTH4 (3 << 14) /* 4 byte width (Word) */
+#define DCMD_LENGTH 0x01fff /* length mask (max = 8K - 1) */
+
/*
* Descriptor structure for PXA's DMA engine
* Note: this structure must always be aligned to a 16-byte boundary.
#define _PCMCIA1Attr _PCMCIAAttr (1) /* PCMCIA 1 Attribute */
#define _PCMCIA1Mem _PCMCIAMem (1) /* PCMCIA 1 Memory */
-
-
-/*
- * DMA Controller
- */
-#define DCSR(x) __REG2(0x40000000, (x) << 2)
-
-#define DCSR_RUN (1 << 31) /* Run Bit (read / write) */
-#define DCSR_NODESC (1 << 30) /* No-Descriptor Fetch (read / write) */
-#define DCSR_STOPIRQEN (1 << 29) /* Stop Interrupt Enable (read / write) */
-#define DCSR_REQPEND (1 << 8) /* Request Pending (read-only) */
-#define DCSR_STOPSTATE (1 << 3) /* Stop State (read-only) */
-#define DCSR_ENDINTR (1 << 2) /* End Interrupt (read / write) */
-#define DCSR_STARTINTR (1 << 1) /* Start Interrupt (read / write) */
-#define DCSR_BUSERR (1 << 0) /* Bus Error Interrupt (read / write) */
-
-#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
-#define DCSR_EORIRQEN (1 << 28) /* End of Receive Interrupt Enable (R/W) */
-#define DCSR_EORJMPEN (1 << 27) /* Jump to next descriptor on EOR */
-#define DCSR_EORSTOPEN (1 << 26) /* STOP on an EOR */
-#define DCSR_SETCMPST (1 << 25) /* Set Descriptor Compare Status */
-#define DCSR_CLRCMPST (1 << 24) /* Clear Descriptor Compare Status */
-#define DCSR_CMPST (1 << 10) /* The Descriptor Compare Status */
-#define DCSR_EORINTR (1 << 9) /* The end of Receive */
-#endif
-
-#define DALGN __REG(0x400000a0) /* DMA Alignment Register */
-#define DINT __REG(0x400000f0) /* DMA Interrupt Register */
-
-#define DRCMR(n) (*(((n) < 64) ? \
- &__REG2(0x40000100, ((n) & 0x3f) << 2) : \
- &__REG2(0x40001100, ((n) & 0x3f) << 2)))
-
-#define DRCMR_MAPVLD (1 << 7) /* Map Valid (read / write) */
-#define DRCMR_CHLNUM 0x1f /* mask for Channel Number (read / write) */
-
-#define DDADR(x) __REG2(0x40000200, (x) << 4)
-#define DSADR(x) __REG2(0x40000204, (x) << 4)
-#define DTADR(x) __REG2(0x40000208, (x) << 4)
-#define DCMD(x) __REG2(0x4000020c, (x) << 4)
-
-#define DDADR_DESCADDR 0xfffffff0 /* Address of next descriptor (mask) */
-#define DDADR_STOP (1 << 0) /* Stop (read / write) */
-
-#define DCMD_INCSRCADDR (1 << 31) /* Source Address Increment Setting. */
-#define DCMD_INCTRGADDR (1 << 30) /* Target Address Increment Setting. */
-#define DCMD_FLOWSRC (1 << 29) /* Flow Control by the source. */
-#define DCMD_FLOWTRG (1 << 28) /* Flow Control by the target. */
-#define DCMD_STARTIRQEN (1 << 22) /* Start Interrupt Enable */
-#define DCMD_ENDIRQEN (1 << 21) /* End Interrupt Enable */
-#define DCMD_ENDIAN (1 << 18) /* Device Endian-ness. */
-#define DCMD_BURST8 (1 << 16) /* 8 byte burst */
-#define DCMD_BURST16 (2 << 16) /* 16 byte burst */
-#define DCMD_BURST32 (3 << 16) /* 32 byte burst */
-#define DCMD_WIDTH1 (1 << 14) /* 1 byte width */
-#define DCMD_WIDTH2 (2 << 14) /* 2 byte width (HalfWord) */
-#define DCMD_WIDTH4 (3 << 14) /* 4 byte width (Word) */
-#define DCMD_LENGTH 0x01fff /* length mask (max = 8K - 1) */
-
/*
* Real Time Clock
*/
#include <linux/videodev2.h>
#include <mach/dma.h>
-#include <mach/pxa-regs.h>
#include <mach/camera.h>
#define PXA_CAM_VERSION_CODE KERNEL_VERSION(0, 0, 5)
#include <asm/sizes.h>
-#include <mach/dma.h>
#include <mach/hardware.h>
-#include <mach/pxa-regs.h>
+#include <mach/dma.h>
#include <mach/mmc.h>
#include "pxamci.h"
#include <linux/irq.h>
#include <mach/dma.h>
-#include <mach/pxa-regs.h>
#include <mach/pxa3xx_nand.h>
#define CHIP_DELAY_TIMEOUT (2 * HZ/10)
#include <asm/delay.h>
#include <mach/dma.h>
-#include <mach/hardware.h>
-#include <mach/pxa-regs.h>
#include <mach/regs-ssp.h>
#include <mach/ssp.h>
#include <mach/pxa2xx_spi.h>
#include <sound/pxa2xx-lib.h>
#include <mach/hardware.h>
-#include <mach/pxa-regs.h>
+#include <mach/dma.h>
#include <mach/regs-ssp.h>
#include <mach/audio.h>
#include <mach/ssp.h>
#include <sound/pxa2xx-lib.h>
#include <mach/hardware.h>
-#include <mach/pxa-regs.h>
#include <mach/regs-ac97.h>
+#include <mach/dma.h>
#include "pxa2xx-pcm.h"
#include "pxa2xx-ac97.h"
#include <sound/pxa2xx-lib.h>
#include <mach/hardware.h>
-#include <mach/pxa-regs.h>
+#include <mach/dma.h>
#include <mach/pxa2xx-gpio.h>
#include <mach/audio.h>
projects / openwrt / staging / blogic.git / commitdiff