Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.16.0.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
#size-cells = <2>;
ranges;
- cbus: cbus@c1100000 {
+ cbus: bus@c1100000 {
compatible = "simple-bus";
reg = <0x0 0xc1100000 0x0 0x100000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
+ gpio_intc: interrupt-controller@9880 {
+ compatible = "amlogic,meson-gpio-intc";
+ reg = <0x0 0x9880 0x0 0x10>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>;
+ status = "disabled";
+ };
+
reset: reset-controller@4404 {
compatible = "amlogic,meson-gx-reset", "amlogic,meson-gxbb-reset";
- reg = <0x0 0x04404 0x0 0x20>;
+ reg = <0x0 0x04404 0x0 0x9c>;
#reset-cells = <1>;
};
uart_A: serial@84c0 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x84c0 0x0 0x14>;
+ compatible = "amlogic,meson-gx-uart";
+ reg = <0x0 0x84c0 0x0 0x18>;
interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
status = "disabled";
};
uart_B: serial@84dc {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x84dc 0x0 0x14>;
+ compatible = "amlogic,meson-gx-uart";
+ reg = <0x0 0x84dc 0x0 0x18>;
interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
status = "disabled";
};
};
uart_C: serial@8700 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x8700 0x0 0x14>;
+ compatible = "amlogic,meson-gx-uart";
+ reg = <0x0 0x8700 0x0 0x18>;
interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
status = "disabled";
};
};
};
- aobus: aobus@c8100000 {
+ aobus: bus@c8100000 {
compatible = "simple-bus";
reg = <0x0 0xc8100000 0x0 0x100000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
- clkc_AO: clock-controller@040 {
- compatible = "amlogic,gx-aoclkc", "amlogic,gxbb-aoclkc";
- reg = <0x0 0x00040 0x0 0x4>;
- #clock-cells = <1>;
- #reset-cells = <1>;
+ sysctrl_AO: sys-ctrl@0 {
+ compatible = "amlogic,meson-gx-ao-sysctrl", "syscon", "simple-mfd";
+ reg = <0x0 0x0 0x0 0x100>;
+
+ pwrc_vpu: power-controller-vpu {
+ compatible = "amlogic,meson-gx-pwrc-vpu";
+ #power-domain-cells = <0>;
+ amlogic,hhi-sysctrl = <&sysctrl>;
+ };
+
+ clkc_AO: clock-controller {
+ compatible = "amlogic,meson-gx-aoclkc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+ };
+
+ cec_AO: cec@100 {
+ compatible = "amlogic,meson-gx-ao-cec";
+ reg = <0x0 0x00100 0x0 0x14>;
+ interrupts = <GIC_SPI 199 IRQ_TYPE_EDGE_RISING>;
+ };
+
+ sec_AO: ao-secure@140 {
+ compatible = "amlogic,meson-gx-ao-secure", "syscon";
+ reg = <0x0 0x140 0x0 0x140>;
+ amlogic,has-chip-id;
};
uart_AO: serial@4c0 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x004c0 0x0 0x14>;
+ compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
+ reg = <0x0 0x004c0 0x0 0x18>;
interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
status = "disabled";
};
uart_AO_B: serial@4e0 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x004e0 0x0 0x14>;
+ compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
+ reg = <0x0 0x004e0 0x0 0x18>;
interrupts = <GIC_SPI 197 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
status = "disabled";
};
};
};
- hiubus: hiubus@c883c000 {
+ hiubus: bus@c883c000 {
compatible = "simple-bus";
reg = <0x0 0xc883c000 0x0 0x2000>;
#address-cells = <2>;
#size-cells = <2>;
ranges = <0x0 0x0 0x0 0xc883c000 0x0 0x2000>;
+ sysctrl: system-controller@0 {
+ compatible = "amlogic,meson-gx-hhi-sysctrl", "syscon", "simple-mfd";
+ reg = <0 0 0 0x400>;
+ };
+
mailbox: mailbox@404 {
compatible = "amlogic,meson-gx-mhu", "amlogic,meson-gxbb-mhu";
reg = <0 0x404 0 0x4c>;
- interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
- <0 209 IRQ_TYPE_EDGE_RISING>,
- <0 210 IRQ_TYPE_EDGE_RISING>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 209 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 210 IRQ_TYPE_EDGE_RISING>;
#mbox-cells = <1>;
};
};
compatible = "amlogic,meson-gx-dwmac", "amlogic,meson-gxbb-dwmac", "snps,dwmac";
reg = <0x0 0xc9410000 0x0 0x10000
0x0 0xc8834540 0x0 0x4>;
- interrupts = <0 8 1>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "macirq";
status = "disabled";
};
/ {
compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb";
model = "Hardkernel ODROID-C2";
-
+
aliases {
serial0 = &uart_AO;
};
compatible = "mmc-pwrseq-emmc";
reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
};
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+};
+
+&cec_AO {
+ status = "okay";
+ pinctrl-0 = <&ao_cec_pins>;
+ pinctrl-names = "default";
+ hdmi-phandle = <&hdmi_tx>;
};
ðmac {
#size-cells = <0>;
eth_phy0: ethernet-phy@0 {
+ /* Realtek RTL8211F (0x001cc916) */
reg = <0>;
+ interrupt-parent = <&gpio_intc>;
+ /* MAC_INTR on GPIOZ_15 */
+ interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
eee-broken-1000t;
};
};
};
};
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
+ pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
&i2c_A {
status = "okay";
pinctrl-0 = <&i2c_a_pins>;
"USB HUB nRESET", "USB OTG Power En",
"J7 Header Pin2", "IR In", "J7 Header Pin4",
"J7 Header Pin6", "J7 Header Pin5", "J7 Header Pin7",
- "HDMI CEC", "SYS LED";
+ "HDMI CEC", "SYS LED",
+ /* GPIO_TEST_N */
+ "";
};
&pinctrl_periphs {
"J2 Header Pin12", "J2 Header Pin13",
"J2 Header Pin8", "J2 Header Pin10",
"", "", "", "", "",
- "J2 Header Pin11", "", "J2 Header Pin7",
+ "J2 Header Pin11", "", "J2 Header Pin7", "",
/* Bank GPIOCLK */
- "", "", "", "",
- /* GPIO_TEST_N */
- "";
+ "", "", "", "";
};
&saradc {
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
/* eMMC */
&sd_emmc_c {
status = "okay";
- pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
- cap-sd-highspeed;
max-frequency = <200000000>;
non-removable;
disable-wp;
&usb1_phy {
status = "okay";
+ phy-supply = <&usb_otg_pwr>;
};
&usb0 {
};
};
+&cec_AO {
+ clocks = <&clkc_AO CLKID_AO_CEC_32K>;
+ clock-names = "core";
+};
+
+&clkc_AO {
+ compatible = "amlogic,meson-gxbb-aoclkc", "amlogic,meson-gx-aoclkc";
+};
+
ðmac {
clocks = <&clkc CLKID_ETH>,
<&clkc CLKID_FCLK_DIV2>,
clock-names = "stmmaceth", "clkin0", "clkin1";
};
+&gpio_intc {
+ compatible = "amlogic,meson-gpio-intc",
+ "amlogic,meson-gxbb-gpio-intc";
+ status = "okay";
+};
+
&hdmi_tx {
compatible = "amlogic,meson-gxbb-dw-hdmi", "amlogic,meson-gx-dw-hdmi";
resets = <&reset RESET_HDMITX_CAPB3>,
reg-names = "mux", "pull", "pull-enable", "gpio";
gpio-controller;
#gpio-cells = <2>;
- gpio-ranges = <&pinctrl_periphs 0 14 120>;
+ gpio-ranges = <&pinctrl_periphs 0 0 119>;
};
emmc_pins: emmc {
mux {
groups = "emmc_nand_d07",
"emmc_cmd",
- "emmc_clk",
- "emmc_ds";
+ "emmc_clk";
+ function = "emmc";
+ };
+ };
+
+ emmc_ds_pins: emmc-ds {
+ mux {
+ groups = "emmc_ds";
function = "emmc";
};
};
+ emmc_clk_gate_pins: emmc_clk_gate {
+ mux {
+ groups = "BOOT_8";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "BOOT_8";
+ bias-pull-down;
+ };
+ };
+
nor_pins: nor {
mux {
groups = "nor_d",
};
};
+ sdcard_clk_gate_pins: sdcard_clk_gate {
+ mux {
+ groups = "CARD_2";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "CARD_2";
+ bias-pull-down;
+ };
+ };
+
sdio_pins: sdio {
mux {
groups = "sdio_d0",
};
};
+ sdio_clk_gate_pins: sdio_clk_gate {
+ mux {
+ groups = "GPIOX_4";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "GPIOX_4";
+ bias-pull-down;
+ };
+ };
+
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
};
};
+&pwrc_vpu {
+ resets = <&reset RESET_VIU>,
+ <&reset RESET_VENC>,
+ <&reset RESET_VCBUS>,
+ <&reset RESET_BT656>,
+ <&reset RESET_DVIN_RESET>,
+ <&reset RESET_RDMA>,
+ <&reset RESET_VENCI>,
+ <&reset RESET_VENCP>,
+ <&reset RESET_VDAC>,
+ <&reset RESET_VDI6>,
+ <&reset RESET_VENCL>,
+ <&reset RESET_VID_LOCK>;
+ clocks = <&clkc CLKID_VPU>,
+ <&clkc CLKID_VAPB>;
+ clock-names = "vpu", "vapb";
+ /*
+ * VPU clocking is provided by two identical clock paths
+ * VPU_0 and VPU_1 muxed to a single clock by a glitch
+ * free mux to safely change frequency while running.
+ * Same for VAPB but with a final gate after the glitch free mux.
+ */
+ assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
+ <&clkc CLKID_VPU_0>,
+ <&clkc CLKID_VPU>, /* Glitch free mux */
+ <&clkc CLKID_VAPB_0_SEL>,
+ <&clkc CLKID_VAPB_0>,
+ <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
+ assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_VPU_0>,
+ <&clkc CLKID_FCLK_DIV4>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_VAPB_0>;
+ assigned-clock-rates = <0>, /* Do Nothing */
+ <666666666>,
+ <0>, /* Do Nothing */
+ <0>, /* Do Nothing */
+ <250000000>,
+ <0>; /* Do Nothing */
+};
+
&saradc {
compatible = "amlogic,meson-gxbb-saradc", "amlogic,meson-saradc";
clocks = <&xtal>,
<&clkc CLKID_SAR_ADC>,
- <&clkc CLKID_SANA>,
<&clkc CLKID_SAR_ADC_CLK>,
<&clkc CLKID_SAR_ADC_SEL>;
- clock-names = "clkin", "core", "sana", "adc_clk", "adc_sel";
+ clock-names = "clkin", "core", "adc_clk", "adc_sel";
};
&sd_emmc_a {
clocks = <&clkc CLKID_SD_EMMC_A>,
- <&xtal>,
+ <&clkc CLKID_SD_EMMC_A_CLK0>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
&sd_emmc_b {
clocks = <&clkc CLKID_SD_EMMC_B>,
- <&xtal>,
+ <&clkc CLKID_SD_EMMC_B_CLK0>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
&sd_emmc_c {
clocks = <&clkc CLKID_SD_EMMC_C>,
- <&xtal>,
+ <&clkc CLKID_SD_EMMC_C_CLK0>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
clocks = <&clkc CLKID_SPI>;
};
+&uart_A {
+ clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_AO {
+ clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_AO_B {
+ clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_B {
+ clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_C {
+ clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+};
+
&vpu {
compatible = "amlogic,meson-gxbb-vpu", "amlogic,meson-gx-vpu";
+ power-domains = <&pwrc_vpu>;
};
};
};
+&cec_AO {
+ status = "okay";
+ pinctrl-0 = <&ao_cec_pins>;
+ pinctrl-names = "default";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
&hdmi_tx {
status = "okay";
pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
linux,rc-map-name = "rc-geekbox";
};
+&pinctrl_aobus {
+ gpio-line-names = "UART TX",
+ "UART RX",
+ "Power Key In",
+ "J9 Header Pin35",
+ "J9 Header Pin16",
+ "J9 Header Pin15",
+ "J9 Header Pin33",
+ "IR In",
+ "HDMI CEC",
+ "SYS LED",
+ /* GPIO_TEST_N */
+ "";
+};
+
+&pinctrl_periphs {
+ gpio-line-names = /* Bank GPIOZ */
+ "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "",
+ "Power OFF",
+ "VCCK Enable",
+ /* Bank GPIOH */
+ "HDMI HPD", "HDMI SDA", "HDMI SCL",
+ "HDMI_5V_EN", "SPDIF",
+ "J9 Header Pin37",
+ "J9 Header Pin30",
+ "J9 Header Pin29",
+ "J9 Header Pin32",
+ "J9 Header Pin31",
+ /* Bank BOOT */
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3",
+ "eMMC D4", "eMMC D5", "eMMC D6", "eMMC D7",
+ "eMMC Clk", "eMMC Reset", "eMMC CMD",
+ "", "BOOT_MODE", "", "", "eMMC Data Strobe",
+ /* Bank CARD */
+ "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+ "SDCard D3", "SDCard D2", "SDCard Det",
+ /* Bank GPIODV */
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK",
+ "VCCK Regulator", "VDDEE Regulator",
+ /* Bank GPIOX */
+ "WIFI SDIO D0", "WIFI SDIO D1", "WIFI SDIO D2",
+ "WIFI SDIO D3", "WIFI SDIO CLK", "WIFI SDIO CMD",
+ "WIFI Power Enable", "WIFI WAKE HOST",
+ "Bluetooth PCM DOUT", "Bluetooth PCM DIN",
+ "Bluetooth PCM SYNC", "Bluetooth PCM CLK",
+ "Bluetooth UART TX", "Bluetooth UART RX",
+ "Bluetooth UART CTS", "Bluetooth UART RTS",
+ "WIFI 32K", "Bluetooth Enable",
+ "Bluetooth WAKE HOST",
+ /* Bank GPIOCLK */
+ "", "J9 Header Pin39";
+};
+
&pwm_AO_ab {
status = "okay";
pinctrl-0 = <&pwm_ao_a_3_pins>, <&pwm_ao_b_pins>;
reg = <0x0 0x0 0x0 0x80000000>;
};
+ hdmi_5v: regulator-hdmi-5v {
+ compatible = "regulator-fixed";
+
+ regulator-name = "HDMI_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
vcc_3v3: regulator-vcc_3v3 {
compatible = "regulator-fixed";
regulator-name = "VCC_3V3";
states = <3300000 0>,
<1800000 1>;
+
+ regulator-settling-time-up-us = <200>;
+ regulator-settling-time-down-us = <50000>;
+ };
+
+ vddio_ao18: regulator-vddio_ao18 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDIO_AO18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
};
vddio_boot: regulator-vddio_boot {
};
};
+&cec_AO {
+ status = "okay";
+ pinctrl-0 = <&ao_cec_pins>;
+ pinctrl-names = "default";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
&cvbs_vdac_port {
cvbs_vdac_out: endpoint {
remote-endpoint = <&cvbs_connector_in>;
status = "okay";
};
+&internal_phy {
+ pinctrl-0 = <ð_link_led_pins>, <ð_act_led_pins>;
+ pinctrl-names = "default";
+};
+
&ir {
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
};
};
+&pinctrl_aobus {
+ gpio-line-names = "UART TX",
+ "UART RX",
+ "Blue LED",
+ "SDCard Voltage Switch",
+ "7J1 Header Pin5",
+ "7J1 Header Pin3",
+ "7J1 Header Pin12",
+ "IR In",
+ "9J3 Switch HDMI CEC/7J1 Header Pin11",
+ "7J1 Header Pin13",
+ /* GPIO_TEST_N */
+ "7J1 Header Pin15";
+};
+
+&pinctrl_periphs {
+ gpio-line-names = /* Bank GPIOZ */
+ "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "",
+ "Eth Link LED", "Eth Activity LED",
+ /* Bank GPIOH */
+ "HDMI HPD", "HDMI SDA", "HDMI SCL",
+ "HDMI_5V_EN", "9J1 Header Pin2",
+ "Analog Audio Mute",
+ "2J3 Header Pin6",
+ "2J3 Header Pin5",
+ "2J3 Header Pin4",
+ "2J3 Header Pin3",
+ /* Bank BOOT */
+ "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3",
+ "eMMC D4", "eMMC D5", "eMMC D6", "eMMC D7",
+ "eMMC Clk", "eMMC Reset", "eMMC CMD",
+ "ALT BOOT MODE", "", "", "", "eMMC Data Strobe",
+ /* Bank CARD */
+ "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD",
+ "SDCard D3", "SDCard D2", "SDCard Det",
+ /* Bank GPIODV */
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "", "", "", "", "",
+ "Green LED", "VCCK Enable",
+ "7J1 Header Pin27", "7J1 Header Pin28",
+ "VCCK Regulator", "VDDEE Regulator",
+ /* Bank GPIOX */
+ "7J1 Header Pin22", "7J1 Header Pin26",
+ "7J1 Header Pin36", "7J1 Header Pin38",
+ "7J1 Header Pin40", "7J1 Header Pin37",
+ "7J1 Header Pin33", "7J1 Header Pin35",
+ "7J1 Header Pin19", "7J1 Header Pin21",
+ "7J1 Header Pin24", "7J1 Header Pin23",
+ "7J1 Header Pin8", "7J1 Header Pin10",
+ "7J1 Header Pin16", "7J1 Header Pin18",
+ "7J1 Header Pin32", "7J1 Header Pin29",
+ "7J1 Header Pin31",
+ /* Bank GPIOCLK */
+ "7J1 Header Pin7", "";
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&vddio_ao18>;
+};
+
/* SD card */
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
max-frequency = <100000000>;
disable-wp;
/* eMMC */
&sd_emmc_c {
status = "okay";
- pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
cap-mmc-highspeed;
+ mmc-ddr-3_3v;
max-frequency = <50000000>;
non-removable;
disable-wp;
};
};
+&cec_AO {
+ status = "okay";
+ pinctrl-0 = <&ao_cec_pins>;
+ pinctrl-names = "default";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
&cvbs_vdac_port {
cvbs_vdac_out: endpoint {
remote-endpoint = <&cvbs_connector_in>;
reg = <0x0 0x0 0x0 0x80000000>;
};
+ hdmi_5v: regulator-hdmi-5v {
+ compatible = "regulator-fixed";
+
+ regulator-name = "HDMI_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpio = <&gpio GPIOH_3 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
vddio_boot: regulator-vddio_boot {
compatible = "regulator-fixed";
regulator-name = "VDDIO_BOOT";
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
/* eMMC */
&sd_emmc_c {
status = "okay";
- pinctrl-0 = <&emmc_pins>;
- pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
- cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <200000000>;
non-removable;
#include "meson-gx.dtsi"
#include <dt-bindings/clock/gxbb-clkc.h>
+#include <dt-bindings/clock/gxbb-aoclkc.h>
#include <dt-bindings/gpio/meson-gxl-gpio.h>
#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
/ {
compatible = "amlogic,meson-gxl";
+
+ reserved-memory {
+ /* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved_alt: secmon@5000000 {
+ reg = <0x0 0x05000000 0x0 0x300000>;
+ no-map;
+ };
+ };
};
ðmac {
};
};
+&cec_AO {
+ clocks = <&clkc_AO CLKID_AO_CEC_32K>;
+ clock-names = "core";
+};
+
+&clkc_AO {
+ compatible = "amlogic,meson-gxl-aoclkc", "amlogic,meson-gx-aoclkc";
+};
+
+&gpio_intc {
+ compatible = "amlogic,meson-gpio-intc",
+ "amlogic,meson-gxl-gpio-intc";
+ status = "okay";
+};
+
&hdmi_tx {
compatible = "amlogic,meson-gxl-dw-hdmi", "amlogic,meson-gx-dw-hdmi";
resets = <&reset RESET_HDMITX_CAPB3>,
reg-names = "mux", "pull", "pull-enable", "gpio";
gpio-controller;
#gpio-cells = <2>;
- gpio-ranges = <&pinctrl_periphs 0 10 101>;
+ gpio-ranges = <&pinctrl_periphs 0 0 100>;
};
emmc_pins: emmc {
mux {
groups = "emmc_nand_d07",
"emmc_cmd",
- "emmc_clk",
- "emmc_ds";
+ "emmc_clk";
function = "emmc";
};
};
+ emmc_ds_pins: emmc-ds {
+ mux {
+ groups = "emmc_ds";
+ function = "emmc";
+ };
+ };
+
+ emmc_clk_gate_pins: emmc_clk_gate {
+ mux {
+ groups = "BOOT_8";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "BOOT_8";
+ bias-pull-down;
+ };
+ };
+
nor_pins: nor {
mux {
groups = "nor_d",
};
};
+ sdcard_clk_gate_pins: sdcard_clk_gate {
+ mux {
+ groups = "CARD_2";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "CARD_2";
+ bias-pull-down;
+ };
+ };
+
sdio_pins: sdio {
mux {
groups = "sdio_d0",
};
};
+ sdio_clk_gate_pins: sdio_clk_gate {
+ mux {
+ groups = "GPIOX_4";
+ function = "gpio_periphs";
+ };
+ cfg-pull-down {
+ pins = "GPIOX_4";
+ bias-pull-down;
+ };
+ };
+
sdio_irq_pins: sdio_irq {
mux {
groups = "sdio_irq";
internal_phy: ethernet-phy@8 {
compatible = "ethernet-phy-id0181.4400", "ethernet-phy-ieee802.3-c22";
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
reg = <8>;
max-speed = <100>;
};
};
};
+&pwrc_vpu {
+ resets = <&reset RESET_VIU>,
+ <&reset RESET_VENC>,
+ <&reset RESET_VCBUS>,
+ <&reset RESET_BT656>,
+ <&reset RESET_DVIN_RESET>,
+ <&reset RESET_RDMA>,
+ <&reset RESET_VENCI>,
+ <&reset RESET_VENCP>,
+ <&reset RESET_VDAC>,
+ <&reset RESET_VDI6>,
+ <&reset RESET_VENCL>,
+ <&reset RESET_VID_LOCK>;
+ clocks = <&clkc CLKID_VPU>,
+ <&clkc CLKID_VAPB>;
+ clock-names = "vpu", "vapb";
+ /*
+ * VPU clocking is provided by two identical clock paths
+ * VPU_0 and VPU_1 muxed to a single clock by a glitch
+ * free mux to safely change frequency while running.
+ * Same for VAPB but with a final gate after the glitch free mux.
+ */
+ assigned-clocks = <&clkc CLKID_VPU_0_SEL>,
+ <&clkc CLKID_VPU_0>,
+ <&clkc CLKID_VPU>, /* Glitch free mux */
+ <&clkc CLKID_VAPB_0_SEL>,
+ <&clkc CLKID_VAPB_0>,
+ <&clkc CLKID_VAPB_SEL>; /* Glitch free mux */
+ assigned-clock-parents = <&clkc CLKID_FCLK_DIV3>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_VPU_0>,
+ <&clkc CLKID_FCLK_DIV4>,
+ <0>, /* Do Nothing */
+ <&clkc CLKID_VAPB_0>;
+ assigned-clock-rates = <0>, /* Do Nothing */
+ <666666666>,
+ <0>, /* Do Nothing */
+ <0>, /* Do Nothing */
+ <250000000>,
+ <0>; /* Do Nothing */
+};
+
&saradc {
compatible = "amlogic,meson-gxl-saradc", "amlogic,meson-saradc";
clocks = <&xtal>,
<&clkc CLKID_SAR_ADC>,
- <&clkc CLKID_SANA>,
<&clkc CLKID_SAR_ADC_CLK>,
<&clkc CLKID_SAR_ADC_SEL>;
- clock-names = "clkin", "core", "sana", "adc_clk", "adc_sel";
+ clock-names = "clkin", "core", "adc_clk", "adc_sel";
};
&sd_emmc_a {
clocks = <&clkc CLKID_SD_EMMC_A>,
- <&xtal>,
+ <&clkc CLKID_SD_EMMC_A_CLK0>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
&sd_emmc_b {
clocks = <&clkc CLKID_SD_EMMC_B>,
- <&xtal>,
+ <&clkc CLKID_SD_EMMC_B_CLK0>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
&sd_emmc_c {
clocks = <&clkc CLKID_SD_EMMC_C>,
- <&xtal>,
+ <&clkc CLKID_SD_EMMC_C_CLK0>,
<&clkc CLKID_FCLK_DIV2>;
clock-names = "core", "clkin0", "clkin1";
};
clocks = <&clkc CLKID_SPI>;
};
+&uart_A {
+ clocks = <&xtal>, <&clkc CLKID_UART0>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_AO {
+ clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_AO_B {
+ clocks = <&xtal>, <&clkc CLKID_CLK81>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_B {
+ clocks = <&xtal>, <&clkc CLKID_UART1>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+};
+
+&uart_C {
+ clocks = <&xtal>, <&clkc CLKID_UART2>, <&xtal>;
+ clock-names = "xtal", "pclk", "baud";
+};
+
&vpu {
compatible = "amlogic,meson-gxl-vpu", "amlogic,meson-gx-vpu";
+ power-domains = <&pwrc_vpu>;
};
#define CLKID_AO_UART1 3
#define CLKID_AO_UART2 4
#define CLKID_AO_IR_BLASTER 5
+#define CLKID_AO_CEC_32K 6
#endif
+/* SPDX-License-Identifier: GPL-2.0 */
/*
* GXBB clock tree IDs
*/
#ifndef __GXBB_CLKC_H
#define __GXBB_CLKC_H
+#define CLKID_SYS_PLL 0
#define CLKID_HDMI_PLL 2
+#define CLKID_FIXED_PLL 3
#define CLKID_FCLK_DIV2 4
#define CLKID_FCLK_DIV3 5
#define CLKID_FCLK_DIV4 6
+#define CLKID_FCLK_DIV5 7
+#define CLKID_FCLK_DIV7 8
#define CLKID_GP0_PLL 9
#define CLKID_CLK81 12
+#define CLKID_MPLL0 13
+#define CLKID_MPLL1 14
#define CLKID_MPLL2 15
+#define CLKID_DDR 16
+#define CLKID_DOS 17
+#define CLKID_ISA 18
+#define CLKID_PL301 19
+#define CLKID_PERIPHS 20
#define CLKID_SPICC 21
#define CLKID_I2C 22
#define CLKID_SAR_ADC 23
+#define CLKID_SMART_CARD 24
#define CLKID_RNG0 25
#define CLKID_UART0 26
+#define CLKID_SDHC 27
+#define CLKID_STREAM 28
+#define CLKID_ASYNC_FIFO 29
+#define CLKID_SDIO 30
+#define CLKID_ABUF 31
+#define CLKID_HIU_IFACE 32
+#define CLKID_ASSIST_MISC 33
#define CLKID_SPI 34
#define CLKID_ETH 36
+#define CLKID_I2S_SPDIF 35
+#define CLKID_DEMUX 37
#define CLKID_AIU_GLUE 38
#define CLKID_IEC958 39
#define CLKID_I2S_OUT 40
+#define CLKID_AMCLK 41
+#define CLKID_AIFIFO2 42
+#define CLKID_MIXER 43
#define CLKID_MIXER_IFACE 44
+#define CLKID_ADC 45
+#define CLKID_BLKMV 46
#define CLKID_AIU 47
#define CLKID_UART1 48
+#define CLKID_G2D 49
#define CLKID_USB0 50
#define CLKID_USB1 51
+#define CLKID_RESET 52
+#define CLKID_NAND 53
+#define CLKID_DOS_PARSER 54
#define CLKID_USB 55
+#define CLKID_VDIN1 56
+#define CLKID_AHB_ARB0 57
+#define CLKID_EFUSE 58
+#define CLKID_BOOT_ROM 59
+#define CLKID_AHB_DATA_BUS 60
+#define CLKID_AHB_CTRL_BUS 61
+#define CLKID_HDMI_INTR_SYNC 62
#define CLKID_HDMI_PCLK 63
#define CLKID_USB1_DDR_BRIDGE 64
#define CLKID_USB0_DDR_BRIDGE 65
+#define CLKID_MMC_PCLK 66
+#define CLKID_DVIN 67
#define CLKID_UART2 68
#define CLKID_SANA 69
+#define CLKID_VPU_INTR 70
+#define CLKID_SEC_AHB_AHB3_BRIDGE 71
+#define CLKID_CLK81_A53 72
+#define CLKID_VCLK2_VENCI0 73
+#define CLKID_VCLK2_VENCI1 74
+#define CLKID_VCLK2_VENCP0 75
+#define CLKID_VCLK2_VENCP1 76
#define CLKID_GCLK_VENCI_INT0 77
+#define CLKID_GCLK_VENCI_INT 78
+#define CLKID_DAC_CLK 79
#define CLKID_AOCLK_GATE 80
#define CLKID_IEC958_GATE 81
+#define CLKID_ENC480P 82
+#define CLKID_RNG1 83
+#define CLKID_GCLK_VENCI_INT1 84
+#define CLKID_VCLK2_VENCLMCC 85
+#define CLKID_VCLK2_VENCL 86
+#define CLKID_VCLK_OTHER 87
+#define CLKID_EDP 88
+#define CLKID_AO_MEDIA_CPU 89
+#define CLKID_AO_AHB_SRAM 90
+#define CLKID_AO_AHB_BUS 91
+#define CLKID_AO_IFACE 92
#define CLKID_AO_I2C 93
#define CLKID_SD_EMMC_A 94
#define CLKID_SD_EMMC_B 95
#define CLKID_CTS_AMCLK 107
#define CLKID_CTS_MCLK_I958 110
#define CLKID_CTS_I958 113
+#define CLKID_32K_CLK 114
+#define CLKID_SD_EMMC_A_CLK0 119
+#define CLKID_SD_EMMC_B_CLK0 122
+#define CLKID_SD_EMMC_C_CLK0 125
+#define CLKID_VPU_0_SEL 126
+#define CLKID_VPU_0 128
+#define CLKID_VPU_1_SEL 129
+#define CLKID_VPU_1 131
+#define CLKID_VPU 132
+#define CLKID_VAPB_0_SEL 133
+#define CLKID_VAPB_0 135
+#define CLKID_VAPB_1_SEL 136
+#define CLKID_VAPB_1 138
+#define CLKID_VAPB_SEL 139
+#define CLKID_VAPB 140
#endif /* __GXBB_CLKC_H */
#define GPIOAO_11 11
#define GPIOAO_12 12
#define GPIOAO_13 13
+#define GPIO_TEST_N 14
#define GPIOZ_0 0
#define GPIOZ_1 1
#define GPIOCLK_1 116
#define GPIOCLK_2 117
#define GPIOCLK_3 118
-#define GPIO_TEST_N 119
#endif
#define GPIOAO_7 7
#define GPIOAO_8 8
#define GPIOAO_9 9
+#define GPIO_TEST_N 10
#define GPIOZ_0 0
#define GPIOZ_1 1
#define GPIOX_18 97
#define GPIOCLK_0 98
#define GPIOCLK_1 99
-#define GPIO_TEST_N 100
#endif
projects / project / bcm63xx / u-boot.git / commitdiff