This add support for the Sitecom WL-351 v1 002.
In principle the Engenius ESR9850 should also work with this, but I
don't have the hardware to test it.
Since an external gigabit switch (RTL8366RB) is used,
I had to modify the ramips_esw driver to add a 'bypass' mode, which
just configures it to not filter the vlan tags.
Also two initialization words (FCT2 and FPA2) are set to different
values by u-boot than what the driver is using and it only seems to
work correctly when they not overridden by the driver, so I
added them to the platform specific data as reg_initval_fct2 and
reg_initval_fpa2.
With this wired lan works as expected, however I'm still having some
trouble with the wireless lan:
It only works after I rmmod & re-insmod rt2800pci and then
reconfigure it in the webinterface, but not directly after
rebooting.
The symptom of this is wpad saying:
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: associated (aid 1)
Dec 20 15:45:09 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> WPA: pairwise key handshake completed (RSN)
Dec 20 15:45:22 OpenWrt daemon.info hostapd: wlan1: STA <notebookmac> IEEE 802.11: authenticated
But wpa_supplicant on the client saying:
Authentication with <wl351mac> timed out.
Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de>
SVN-Revision: 29604
whr-g300n)
status_led="whr-g300n:green:router"
;;
+ wl-351)
+ status_led="wl-351:amber:power"
+ ;;
esac
}
v22rw-2x2 | \
wcr-150gn | \
whr-g300n | \
+ wl-351 | \
wr512-3gn)
rt2x00_eeprom_extract "factory" 0 272
;;
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
;;
+ wl-351)
+ ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
+ ucidef_add_switch "rtl8366rb" "1" "1"
+ ucidef_add_switch_vlan "rtl8366rb" "1" "0 1 2 3 5t"
+ ucidef_add_switch_vlan "rtl8366rb" "2" "4 5t"
+ ;;
+
rt-n15)
ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
ucidef_add_switch "rtl8366s" "1" "1"
argus-atp52b | \
b2c | \
nw718 | \
- rt-n15)
+ rt-n15 | \
+ wl-351)
lan_mac=$(ramips_get_mac_binary factory 4)
wan_mac=$(/usr/sbin/maccalc add "$lan_mac" 1)
;;
*"WHR-G300N")
name="whr-g300n"
;;
+ *"Sitecom WL-351 v1 002")
+ name="wl-351"
+ ;;
*"WZR-AGL300NH")
name="wzr-agl300nh"
;;
RAMIPS_MACH_V22RW_2X2, /* Ralink AP-RT3052-V22RW-2X2 */
RAMIPS_MACH_WCR150GN, /* Sparklan WCR-150GN */
RAMIPS_MACH_WHR_G300N, /* Buffalo WHR-G300N */
+ RAMIPS_MACH_WL351, /* Sitecom WL-351 v1 002 */
RAMIPS_MACH_WR512_3GN, /* SH-WR512NU/WS-WR512N1-like 3GN*/
};
enum {
RT305X_ESW_VLAN_CONFIG_NONE = 0,
+ RT305X_ESW_VLAN_CONFIG_BYPASS,
RT305X_ESW_VLAN_CONFIG_LLLLW,
RT305X_ESW_VLAN_CONFIG_WLLLL,
};
struct rt305x_esw_platform_data
{
u8 vlan_config;
+ u32 reg_initval_fct2;
+ u32 reg_initval_fpa2;
};
#endif /* _RT305X_ESW_PLATFORM_H */
select RALINK_DEV_GPIO_BUTTONS
select RALINK_DEV_GPIO_LEDS
+config RT305X_MACH_WL351
+ bool "Sitecom WL-351 support"
+ select RALINK_DEV_GPIO_BUTTONS
+ select RALINK_DEV_GPIO_LEDS
+
config RT305X_MACH_WCR150GN
bool "Sparklan WCR-150GN support"
select RALINK_DEV_GPIO_BUTTONS
obj-$(CONFIG_RT305X_MACH_WCR150GN) += mach-wcr150gn.o
obj-$(CONFIG_RT305X_MACH_WHR_G300N) += mach-whr-g300n.o
obj-$(CONFIG_RT305X_MACH_WR512_3GN) += mach-wr512-3gn.o
-
+obj-$(CONFIG_RT305X_MACH_WL351) += mach-wl351.o
#include "devices.h"
#include <ramips_eth_platform.h>
+#include <rt305x_esw_platform.h>
static struct resource rt305x_flash0_resources[] = {
{
},
};
-struct rt305x_esw_platform_data rt305x_esw_data;
+struct rt305x_esw_platform_data rt305x_esw_data = {
+ .vlan_config = RT305X_ESW_VLAN_CONFIG_NONE,
+ .reg_initval_fct2 = 0x00d6500c,
+ .reg_initval_fpa2 = 0x3f502b28,
+};
+
static struct platform_device rt305x_esw_device = {
.name = "rt305x-esw",
.resource = rt305x_esw_resources,
--- /dev/null
+/*
+ * Sitecom WL-351 v1 002 board support
+ *
+ * Copyright (C) 2011 Tobias Diedrich <ranma+openwrt@tdiedrich.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+
+#include <linux/rtl8366.h>
+
+#include <asm/mach-ralink/machine.h>
+#include <asm/mach-ralink/dev-gpio-buttons.h>
+#include <asm/mach-ralink/dev-gpio-leds.h>
+#include <asm/mach-ralink/rt305x.h>
+#include <asm/mach-ralink/rt305x_regs.h>
+
+#include "devices.h"
+
+#define WL351_GPIO_LED_POWER_AMBER 8
+#define WL351_GPIO_LED_UNPOPULATED_AMBER 12
+#define WL351_GPIO_LED_UNPOPULATED_BLUE 13
+
+#define WL351_GPIO_BUTTON_RESET 10
+#define WL351_GPIO_BUTTON_WPS 0
+
+#define WL351_BUTTONS_POLL_INTERVAL 20
+
+
+static struct gpio_led wl351_leds_gpio[] __initdata = {
+ {
+ .name = "wl-351:amber:power",
+ .gpio = WL351_GPIO_LED_POWER_AMBER,
+ .active_low = 1,
+ }, {
+ .name = "wl-351:amber:unpopulated",
+ .gpio = WL351_GPIO_LED_UNPOPULATED_AMBER,
+ .active_low = 1,
+ }, {
+ .name = "wl-351:blue:unpopulated",
+ .gpio = WL351_GPIO_LED_UNPOPULATED_BLUE,
+ .active_low = 1,
+ }
+};
+
+
+static struct gpio_button wl351_gpio_buttons[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .threshold = 3,
+ .gpio = WL351_GPIO_BUTTON_RESET,
+ .active_low = 1,
+ }, {
+ .desc = "wps",
+ .type = EV_KEY,
+ .code = KEY_WPS_BUTTON,
+ .threshold = 3,
+ .gpio = WL351_GPIO_BUTTON_WPS,
+ .active_low = 1,
+ }
+};
+
+
+#ifdef CONFIG_MTD_PARTITIONS
+static struct mtd_partition wl351_partitions[] = {
+ {
+ .name = "u-boot",
+ .offset = 0,
+ .size = 0x030000,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "u-boot-env",
+ .offset = 0x030000,
+ .size = 0x010000,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "factory",
+ .offset = 0x040000,
+ .size = 0x010000,
+ .mask_flags = MTD_WRITEABLE,
+ }, {
+ .name = "kernel",
+ .offset = 0x050000,
+ .size = 0x110000,
+ }, {
+ .name = "rootfs",
+ .offset = 0x160000,
+ .size = 0x230000,
+ }, {
+ .name = "user (jffs2)",
+ .offset = 0x3F0000,
+ .size = 0x010000,
+ }, {
+ .name = "firmware",
+ .offset = 0x050000,
+ .size = 0x3a0000,
+ }
+};
+#endif /* CONFIG_MTD_PARTITIONS */
+
+static struct physmap_flash_data wl351_flash_data = {
+#ifdef CONFIG_MTD_PARTITIONS
+ .nr_parts = ARRAY_SIZE(wl351_partitions),
+ .parts = wl351_partitions,
+#endif
+};
+
+
+static struct rtl8366_platform_data wl351_switch_data = {
+ .gpio_sda = RT305X_GPIO_I2C_SD,
+ .gpio_sck = RT305X_GPIO_I2C_SCLK,
+};
+
+static struct platform_device wl351_switch = {
+ .name = RTL8366RB_DRIVER_NAME,
+ .id = -1,
+ .dev = {
+ .platform_data = &wl351_switch_data,
+ }
+};
+
+static void __init wl351_init(void)
+{
+ rt305x_gpio_init((RT305X_GPIO_MODE_GPIO <<
+ RT305X_GPIO_MODE_UART0_SHIFT) |
+ RT305X_GPIO_MODE_I2C |
+ RT305X_GPIO_MODE_SPI |
+ RT305X_GPIO_MODE_MDIO);
+ rt305x_register_flash(0, &wl351_flash_data);
+ ramips_register_gpio_leds(-1, ARRAY_SIZE(wl351_leds_gpio),
+ wl351_leds_gpio);
+ ramips_register_gpio_buttons(-1, WL351_BUTTONS_POLL_INTERVAL,
+ ARRAY_SIZE(wl351_gpio_buttons),
+ wl351_gpio_buttons);
+ // external rtl8366rb
+ rt305x_esw_data.vlan_config = RT305X_ESW_VLAN_CONFIG_BYPASS;
+ rt305x_esw_data.reg_initval_fct2 = 0x0002500c;
+ rt305x_esw_data.reg_initval_fpa2 = 0x1f003fff;
+ rt305x_register_ethernet();
+ platform_device_register(&wl351_switch);
+ rt305x_register_wifi();
+ rt305x_register_wdt();
+ rt305x_register_usb();
+}
+
+MIPS_MACHINE(RAMIPS_MACH_WL351, "WL-351", "Sitecom WL-351 v1 002",
+ wl351_init);
(RT305X_ESW_PORTS_NOCPU << RT305X_ESW_POC3_UNTAG_EN_S)),
RT305X_ESW_REG_POC3);
- rt305x_esw_wr(esw, 0x00d6500c, RT305X_ESW_REG_FCT2);
+ rt305x_esw_wr(esw, esw->pdata->reg_initval_fct2, RT305X_ESW_REG_FCT2);
rt305x_esw_wr(esw, 0x0008a301, RT305X_ESW_REG_SGC);
/* Setup SoC Port control register */
(RT305X_ESW_PORTS_CPU << RT305X_ESW_SOCPC_DISBC2CPU_S)),
RT305X_ESW_REG_SOCPC);
- rt305x_esw_wr(esw, 0x3f502b28, RT305X_ESW_REG_FPA2);
+ rt305x_esw_wr(esw, esw->pdata->reg_initval_fpa2, RT305X_ESW_REG_FPA2);
rt305x_esw_wr(esw, 0x00000000, RT305X_ESW_REG_FPA);
/* Force Link/Activity on ports */
case RT305X_ESW_VLAN_CONFIG_NONE:
break;
+ case RT305X_ESW_VLAN_CONFIG_BYPASS:
+ /* Pass all vlan tags to all ports */
+ for (i = 0; i < RT305X_ESW_NUM_VLANS; i++) {
+ rt305x_esw_set_vlan_id(esw, i, i+1);
+ rt305x_esw_set_vmsc(esw, i, RT305X_ESW_PORTS_ALL);
+ }
+ /* Disable VLAN TAG removal, keep aging on. */
+ rt305x_esw_wr(esw,
+ RT305X_ESW_PORTS_ALL << RT305X_ESW_POC3_ENAGING_S,
+ RT305X_ESW_REG_POC3);
+ break;
+
case RT305X_ESW_VLAN_CONFIG_LLLLW:
rt305x_esw_set_vlan_id(esw, 0, 1);
rt305x_esw_set_vlan_id(esw, 1, 2);
$(call Image/Build/Template/GENERIC_4M,$(1),nbg-419n,NBG-419N)
endef
+define Image/Build/Profile/WL351
+ $(call Image/Build/Template/GENERIC_4M,$(1),wl-351,WL-351)
+endef
+
define Image/Build/Profile/NW718
$(call Image/Build/Template/NW718,$(1),nw718,NW718)
endef
$(call Image/Build/Profile/HW5503G,$(1))
$(call Image/Build/Profile/MOFI35003GN,$(1))
$(call Image/Build/Profile/WR5123GN,$(1))
+ $(call Image/Build/Profile/WL351,$(1))
endef
endif
CONFIG_RT305X_MACH_V22RW_2X2=y
CONFIG_RT305X_MACH_WCR150GN=y
CONFIG_RT305X_MACH_WHR_G300N=y
+CONFIG_RT305X_MACH_WL351=y
CONFIG_RT305X_MACH_WR512_3GN=y
# CONFIG_SCSI_DMA is not set
CONFIG_SERIAL_8250_NR_UARTS=4
projects / openwrt / staging / hauke.git / commitdiff