+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2010
- * Stefano Babic, DENX Software Engineering, sbabic@denx.de
- *
- * Based on da850evm.c, original Copyrights follow:
- *
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
- *
- * Based on da830evm.c. Original Copyrights follow:
- *
- * Copyright (C) 2009 Nick Thompson, GE Fanuc, Ltd. <nick.thompson@gefanuc.com>
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <net.h>
-#include <netdev.h>
-#include <asm/mach-types.h>
-#include <asm/arch/hardware.h>
-#include <asm/ti-common/davinci_nand.h>
-#include <asm/arch/emac_defs.h>
-#include <asm/io.h>
-#include <asm/arch/davinci_misc.h>
-#include <asm/gpio.h>
-#include "../../../drivers/video/da8xx-fb.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static const struct da8xx_panel lcd_panel = {
- /* Casio COM57H531x */
- .name = "Casio_COM57H531x",
- .width = 640,
- .height = 480,
- .hfp = 12,
- .hbp = 144,
- .hsw = 30,
- .vfp = 10,
- .vbp = 35,
- .vsw = 3,
- .pxl_clk = 25000000,
- .invert_pxl_clk = 0,
-};
-
-static const struct display_panel disp_panel = {
- QVGA,
- 16,
- 16,
- COLOR_ACTIVE,
-};
-
-static const struct lcd_ctrl_config lcd_cfg = {
- &disp_panel,
- .ac_bias = 255,
- .ac_bias_intrpt = 0,
- .dma_burst_sz = 16,
- .bpp = 16,
- .fdd = 255,
- .tft_alt_mode = 0,
- .stn_565_mode = 0,
- .mono_8bit_mode = 0,
- .invert_line_clock = 1,
- .invert_frm_clock = 1,
- .sync_edge = 0,
- .sync_ctrl = 1,
- .raster_order = 0,
-};
-
-/* SPI0 pin muxer settings */
-static const struct pinmux_config spi1_pins[] = {
- { pinmux(5), 1, 1 },
- { pinmux(5), 1, 2 },
- { pinmux(5), 1, 4 },
- { pinmux(5), 1, 5 }
-};
-
-/* I2C pin muxer settings */
-static const struct pinmux_config i2c_pins[] = {
- { pinmux(4), 2, 2 },
- { pinmux(4), 2, 3 }
-};
-
-/* UART0 pin muxer settings */
-static const struct pinmux_config uart_pins[] = {
- { pinmux(3), 2, 7 },
- { pinmux(3), 2, 6 },
- { pinmux(3), 2, 4 },
- { pinmux(3), 2, 5 }
-};
-
-#ifdef CONFIG_DRIVER_TI_EMAC
-#define HAS_RMII 1
-static const struct pinmux_config emac_pins[] = {
- { pinmux(14), 8, 2 },
- { pinmux(14), 8, 3 },
- { pinmux(14), 8, 4 },
- { pinmux(14), 8, 5 },
- { pinmux(14), 8, 6 },
- { pinmux(14), 8, 7 },
- { pinmux(15), 8, 1 },
- { pinmux(4), 8, 0 },
- { pinmux(4), 8, 1 }
-};
-#endif
-
-#ifdef CONFIG_NAND_DAVINCI
-const struct pinmux_config nand_pins[] = {
- { pinmux(7), 1, 0}, /* CS2 */
- { pinmux(7), 0, 1}, /* CS3 in three state*/
- { pinmux(7), 1, 4 }, /* EMA_WE */
- { pinmux(7), 1, 5 }, /* EMA_OE */
- { pinmux(9), 1, 0 }, /* EMA_D[7] */
- { pinmux(9), 1, 1 }, /* EMA_D[6] */
- { pinmux(9), 1, 2 }, /* EMA_D[5] */
- { pinmux(9), 1, 3 }, /* EMA_D[4] */
- { pinmux(9), 1, 4 }, /* EMA_D[3] */
- { pinmux(9), 1, 5 }, /* EMA_D[2] */
- { pinmux(9), 1, 6 }, /* EMA_D[1] */
- { pinmux(9), 1, 7 }, /* EMA_D[0] */
- { pinmux(12), 1, 5 }, /* EMA_A[2] */
- { pinmux(12), 1, 6 }, /* EMA_A[1] */
- { pinmux(6), 1, 0 } /* EMA_CLK */
-};
-#endif
-
-const struct pinmux_config gpio_pins[] = {
- { pinmux(13), 8, 0 }, /* GPIO6[15] RESETOUTn on SOM*/
- { pinmux(13), 8, 5 }, /* GPIO6[10] U0_SW0 on EA20-00101_2*/
- { pinmux(13), 8, 3 }, /* GPIO6[12] U0_SW1 on EA20-00101_2*/
- { pinmux(19), 8, 5 }, /* GPIO6[1] DISP_ON */
- { pinmux(14), 8, 1 } /* GPIO6[6] LCD_B_PWR*/
-};
-
-const struct pinmux_config lcd_pins[] = {
- { pinmux(17), 2, 1 }, /* LCD_D_0 */
- { pinmux(17), 2, 0 }, /* LCD_D_1 */
- { pinmux(16), 2, 7 }, /* LCD_D_2 */
- { pinmux(16), 2, 6 }, /* LCD_D_3 */
- { pinmux(16), 2, 5 }, /* LCD_D_4 */
- { pinmux(16), 2, 4 }, /* LCD_D_5 */
- { pinmux(16), 2, 3 }, /* LCD_D_6 */
- { pinmux(16), 2, 2 }, /* LCD_D_7 */
- { pinmux(18), 2, 1 }, /* LCD_D_8 */
- { pinmux(18), 2, 0 }, /* LCD_D_9 */
- { pinmux(17), 2, 7 }, /* LCD_D_10 */
- { pinmux(17), 2, 6 }, /* LCD_D_11 */
- { pinmux(17), 2, 5 }, /* LCD_D_12 */
- { pinmux(17), 2, 4 }, /* LCD_D_13 */
- { pinmux(17), 2, 3 }, /* LCD_D_14 */
- { pinmux(17), 2, 2 }, /* LCD_D_15 */
- { pinmux(18), 2, 6 }, /* LCD_PCLK */
- { pinmux(19), 2, 0 }, /* LCD_HSYNC */
- { pinmux(19), 2, 1 }, /* LCD_VSYNC */
- { pinmux(19), 2, 6 }, /* DA850_NLCD_AC_ENB_CS */
-};
-
-const struct pinmux_config halten_pin[] = {
- { pinmux(3), 4, 2 } /* GPIO8[6] HALTEN */
-};
-
-static const struct pinmux_resource pinmuxes[] = {
-#ifdef CONFIG_SPI_FLASH
- PINMUX_ITEM(spi1_pins),
-#endif
- PINMUX_ITEM(uart_pins),
- PINMUX_ITEM(i2c_pins),
-#ifdef CONFIG_NAND_DAVINCI
- PINMUX_ITEM(nand_pins),
-#endif
-#ifdef CONFIG_VIDEO
- PINMUX_ITEM(lcd_pins),
-#endif
-};
-
-static const struct lpsc_resource lpsc[] = {
- { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
- { DAVINCI_LPSC_SPI1 }, /* Serial Flash */
- { DAVINCI_LPSC_EMAC }, /* image download */
- { DAVINCI_LPSC_UART0 }, /* console */
- { DAVINCI_LPSC_GPIO },
- { DAVINCI_LPSC_LCDC }, /* LCD */
-};
-
-int board_early_init_f(void)
-{
- /* PinMux for GPIO */
- if (davinci_configure_pin_mux(gpio_pins, ARRAY_SIZE(gpio_pins)) != 0)
- return 1;
-
- /* Set DISP_ON high to enable LCD output*/
- gpio_direction_output(97, 1);
-
- /* Set the RESETOUTn low */
- gpio_direction_output(111, 0);
-
- /* Set U0_SW0 low for UART0 as console*/
- gpio_direction_output(106, 0);
-
- /* Set U0_SW1 low for UART0 as console*/
- gpio_direction_output(108, 0);
-
- /* Set LCD_B_PWR low to power down LCD Backlight*/
- gpio_direction_output(102, 0);
-
- irq_init();
-
- /*
- * NAND CS setup - cycle counts based on da850evm NAND timings in the
- * Linux kernel @ 25MHz EMIFA
- */
-#ifdef CONFIG_NAND_DAVINCI
- writel((DAVINCI_ABCR_WSETUP(0) |
- DAVINCI_ABCR_WSTROBE(1) |
- DAVINCI_ABCR_WHOLD(0) |
- DAVINCI_ABCR_RSETUP(0) |
- DAVINCI_ABCR_RSTROBE(1) |
- DAVINCI_ABCR_RHOLD(0) |
- DAVINCI_ABCR_TA(0) |
- DAVINCI_ABCR_ASIZE_8BIT),
- &davinci_emif_regs->ab1cr); /* CS2 */
-#endif
-
- /*
- * Power on required peripherals
- * ARM does not have access by default to PSC0 and PSC1
- * assuming here that the DSP bootloader has set the IOPU
- * such that PSC access is available to ARM
- */
- if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)))
- return 1;
-
- /* setup the SUSPSRC for ARM to control emulation suspend */
- writel(readl(&davinci_syscfg_regs->suspsrc) &
- ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
- DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
- DAVINCI_SYSCFG_SUSPSRC_UART0),
- &davinci_syscfg_regs->suspsrc);
-
- /* configure pinmux settings */
- if (davinci_configure_pin_mux_items(pinmuxes, ARRAY_SIZE(pinmuxes)))
- return 1;
-
-#ifdef CONFIG_DRIVER_TI_EMAC
- if (davinci_configure_pin_mux(emac_pins, ARRAY_SIZE(emac_pins)) != 0)
- return 1;
-
- davinci_emac_mii_mode_sel(HAS_RMII);
-#endif /* CONFIG_DRIVER_TI_EMAC */
-
- /* enable the console UART */
- writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST |
- DAVINCI_UART_PWREMU_MGMT_UTRST),
- &davinci_uart0_ctrl_regs->pwremu_mgmt);
-
- /*
- * Reconfigure the LCDC priority to the highest to ensure that
- * the throughput/latency requirements for the LCDC are met.
- */
- writel(readl(&davinci_syscfg_regs->mstpri[2]) & 0x0fffffff,
- &davinci_syscfg_regs->mstpri[2]);
-
-
- return 0;
-}
-
-/*
- * Do not overwrite the console
- * Use always serial for U-Boot console
- */
-int overwrite_console(void)
-{
- return 1;
-}
-
-int board_init(void)
-{
- /* arch number of the board */
- gd->bd->bi_arch_number = MACH_TYPE_EA20;
-
- /* address of boot parameters */
- gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
-
- da8xx_video_init(&lcd_panel, &lcd_cfg, 16);
-
- return 0;
-}
-
-#ifdef CONFIG_BOARD_LATE_INIT
-
-int board_late_init(void)
-{
- unsigned char buf[2];
- int ret;
-
- /* PinMux for HALTEN */
- if (davinci_configure_pin_mux(halten_pin, ARRAY_SIZE(halten_pin)) != 0)
- return 1;
-
- /* Set HALTEN to high */
- gpio_direction_output(134, 1);
-
- /* Set fixed contrast settings for LCD via I2C potentiometer */
- buf[0] = 0x00;
- buf[1] = 0xd7;
- ret = i2c_write(0x2e, 6, 1, buf, 2);
- if (ret)
- puts("\nContrast Settings FAILED\n");
-
- /* Set LCD_B_PWR high to power up LCD Backlight*/
- gpio_set_value(102, 1);
- return 0;
-}
-#endif /* CONFIG_BOARD_LATE_INIT */
-
-#ifdef CONFIG_DRIVER_TI_EMAC
-
-/*
- * Initializes on-board ethernet controllers.
- */
-int board_eth_init(bd_t *bis)
-{
- if (!davinci_emac_initialize()) {
- printf("Error: Ethernet init failed!\n");
- return -1;
- }
-
- /*
- * This board has a RMII PHY. However, the MDC line on the SOM
- * must not be disabled (there is no MII PHY on the
- * baseboard) via the GPIO2[6], because this pin
- * disables at the same time the SPI flash.
- */
-
- return 0;
-}
-#endif /* CONFIG_DRIVER_TI_EMAC */
+++ /dev/null
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/
- *
- * Based on davinci_dvevm.h. Original Copyrights follow:
- *
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * Board
- */
-#define CONFIG_USE_SPIFLASH
-#define CONFIG_SYS_USE_NAND
-#define CONFIG_DRIVER_TI_EMAC_USE_RMII
-#define CONFIG_DRIVER_TI_EMAC_RMII_NO_NEGOTIATE
-#define CONFIG_PREBOOT
-
-/*
- * SoC Configuration
- */
-#define CONFIG_SYS_CLK_FREQ clk_get(DAVINCI_ARM_CLKID)
-#define CONFIG_SYS_OSCIN_FREQ 24000000
-#define CONFIG_SYS_TIMERBASE DAVINCI_TIMER0_BASE
-#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
-/*
- * Memory Info
- */
-#define CONFIG_SYS_MALLOC_LEN (0x10000 + 4*1024*1024) /* malloc() len */
-#define PHYS_SDRAM_1 DAVINCI_DDR_EMIF_DATA_BASE /* DDR Start */
-#define PHYS_SDRAM_1_SIZE (64 << 20) /* SDRAM size 64MB */
-#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* max size from SPRS586*/
-
-/* memtest start addr */
-#define CONFIG_SYS_MEMTEST_START (PHYS_SDRAM_1 + 0x2000000)
-
-/* memtest will be run on 16MB */
-#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0x2000000 + 16*1024*1024)
-
-/*
- * Serial Driver info
- */
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size */
-#define CONFIG_SYS_NS16550_COM1 DAVINCI_UART0_BASE /* Base address of UART0 */
-#define CONFIG_SYS_NS16550_CLK clk_get(DAVINCI_UART2_CLKID)
-
-#define CONFIG_SYS_SPI_BASE DAVINCI_SPI1_BASE
-#define CONFIG_SYS_SPI_CLK clk_get(DAVINCI_SPI1_CLKID)
-
-/*
- * I2C Configuration
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_DAVINCI_I2C_SPEED 100000
-#define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
-
-/*
- * Network & Ethernet Configuration
- */
-#ifdef CONFIG_DRIVER_TI_EMAC
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
-#endif
-
-#ifdef CONFIG_USE_SPIFLASH
-#define CONFIG_ENV_SIZE (8 << 10)
-#define CONFIG_ENV_OFFSET 0x80000
-#define CONFIG_ENV_SECT_SIZE (64 << 10)
-#endif
-
-#if defined(CONFIG_VIDEO)
-#define CONFIG_VIDEO_DA8XX
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VIDEO_BMP_RLE8
-#define CONFIG_VIDEO_BMP_LOGO
-#endif
-
-/*
- * U-Boot general configuration
- */
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Args Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR (PHYS_SDRAM_1 + 0x700000)
-#define CONFIG_MX_CYCLIC
-
-/*
- * Linux Information
- */
-#define LINUX_BOOT_PARAM_ADDR (PHYS_SDRAM_1 + 0x100)
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
-/* NAND Setup */
-#ifdef CONFIG_SYS_USE_NAND
-#define CONFIG_SYS_NAND_PAGE_2K
-#define CONFIG_SYS_NAND_NO_SUBPAGE
-#define CONFIG_SYS_NAND_CS 2
-#define CONFIG_SYS_NAND_BASE DAVINCI_ASYNC_EMIF_DATA_CE2_BASE
-#undef CONFIG_SYS_NAND_HW_ECC
-#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
-#define CONFIG_SYS_NAND_USE_FLASH_BBT
-#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#endif
-
-#if !defined(CONFIG_SYS_USE_NAND) && \
- !defined(CONFIG_USE_NOR) && \
- !defined(CONFIG_USE_SPIFLASH)
-#define CONFIG_ENV_SIZE (16 << 10)
-#endif
-
-/* additions for new relocation code, must added to all boards */
-#define CONFIG_SYS_SDRAM_BASE 0xc0000000
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x1000 - \
- GENERATED_GBL_DATA_SIZE)
-/*
- * Default environment and default scripts
- * to update uboot and load kernel
- */
-
-#define CONFIG_HOSTNAME "ea20"
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "as=3\0" \
- "netdev=eth0\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "rfsbargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rfsbpath}\0" \
- "testrfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${testrfspath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw initrd=" \
- "0x${ramdisk_addr_r},4M\0" \
- "mtdids=nand0=davinci_nand.0\0" \
- "serverip=192.168.5.249\0" \
- "ipaddr=192.168.5.248\0" \
- "rootpath=/opt/eldk/arm\0" \
- "splashpos=230,180\0" \
- "testrfspath=/opt/eldk/test_arm\0" \
- "nandargs=setenv bootargs rootfstype=ubifs ro chk_data_crc " \
- "ubi.mtd=${as} root=ubi0:rootfs\0" \
- "nandrwargs=setenv bootargs rootfstype=ubifs rw chk_data_crc " \
- "ubi.mtd=${as} root=ubi0:rootfs\0" \
- "addip_sta=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0" \
- "addip=if test -n ${ipdyn};then run addip_dyn;" \
- "else run addip_sta;fi\0" \
- "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
- "addtty=setenv bootargs ${bootargs}" \
- " console=${consoledev},${baudrate}n8\0" \
- "addmisc=setenv bootargs ${bootargs} ${misc}\0" \
- "addmem=setenv bootargs ${bootargs} mem=${memory}\0" \
- "consoledev=ttyS0\0" \
- "loadaddr=c0000014\0" \
- "memory=32M\0" \
- "kernel_addr_r=c0700000\0" \
- "hostname=" CONFIG_HOSTNAME "\0" \
- "bootfile=" CONFIG_HOSTNAME "/uImage\0" \
- "ramdisk_file=" CONFIG_HOSTNAME "/image.ext2\0" \
- "flash_self=run ramargs addip addtty addmtd addmisc addmem;" \
- "bootm ${kernel_addr_r}\0" \
- "flash_nfs=run nfsargs addip addtty addmtd addmisc addmem;" \
- "bootm ${kernel_addr}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "run nfsargs addip addtty addmtd addmisc addmem;" \
- "bootm ${kernel_addr_r}\0" \
- "net_rfsb=tftp ${kernel_addr_r} ${bootfile}; " \
- "run rfsbargs addip addtty addmtd addmisc addmem; " \
- "bootm ${kernel_addr_r}\0" \
- "net_testrfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "run testrfsargs addip addtty addmtd addmisc addmem; " \
- "bootm ${kernel_addr_r}\0" \
- "net_self_load=tftp ${kernel_addr_r} ${bootfile};" \
- "tftp ${ramdisk_addr_r} ${ramdisk_file};\0" \
- "nand_nand=ubi part nand0,${as};ubifsmount ubi:rootfs;" \
- "ubifsload ${kernel_addr_r} /boot/uImage;" \
- "ubifsumount; run nandargs addip addtty " \
- "addmtd addmisc addmem;clrlogo;" \
- "bootm ${kernel_addr_r}\0" \
- "nand_nandrw=ubi part nand0,${as};ubifsmount ubi:rootfs;" \
- "ubifsload ${kernel_addr_r} /boot/uImage;" \
- "ubifsumount; run nandrwargs addip addtty " \
- "addmtd addmisc addmem;clrlogo;" \
- "bootm ${kernel_addr_r}\0" \
- "net_nandrw=tftp ${kernel_addr_r} ${bootfile}; run nandrwargs" \
- " addip addtty addmtd addmisc addmem;" \
- "clrlogo;bootm ${kernel_addr_r}\0" \
- "u-boot=" CONFIG_HOSTNAME "/u-boot.bin\0" \
- "load_magic=if sf probe 0;then sf " \
- "read c0000000 0x10000 0x60000;fi\0" \
- "load_nand=ubi part nand0,${as};ubifsmount ubi:rootfs;" \
- "if ubifsload c0000014 /boot/u-boot.bin;" \
- "then mw c0000008 ${filesize};else echo Error reading" \
- " u-boot from nand!;fi\0" \
- "load_net=if sf probe 0;then sf read c0000000 0x10000 " \
- "0x60000;tftp c0000014 ${u-boot};" \
- "mw c0000008 ${filesize};fi\0" \
- "upd=if sf probe 0;then sf erase 10000 60000;" \
- "sf write c0000000 10000 60000;fi\0" \
- "ublupdate=if tftp C0700000 ${ublname};then sf probe 0; " \
- "sf erase 0 10000;" \
- "sf write 0xc0700000 0 ${filesize};fi\0" \
- "ubootupd_net=if run load_net;then echo Updating u-boot;" \
- "if run upd; then echo U-Boot updated;" \
- "else echo Error updating u-boot !;" \
- "echo Board without bootloader !!;" \
- "fi;" \
- "else echo U-Boot not downloaded..exiting;fi\0" \
- "ubootupd_nand=echo run load_magic,run load_nand,run upd;\0" \
- "bootcmd=run net_testrfs\0"
-
-#include <asm/arch/hardware.h>
-
-#endif /* __CONFIG_H */
projects / project / bcm63xx / u-boot.git / commitdiff