Hardware
--------
SoC: NXP P1020 (2x e500 @ 800MHz)
RAM: 256M DDR3 (Micron)
FLASH: 32M NOR (Spansion S29GL128S)
BTN: 1x Reset
WiFi: 1x Atheros AR9590 2.4 bgn 3x3
2x Atheros AR9590 5.0 an 3x3
ETH: 1x Gigabit Ethernet (Atheros AR8033)
LED: System (green/red) - Radio{0,1} (green)
LAN (connected to PHY)
- GE blue
- FE green
Serial is a Cisco-compatible RJ45 next to the ethernet port.
115200-N-8 are the settings for OS and U-Boot.
Installation
------------
1. Grab the OpenWrt initramfs, rename it to
01C8A8C0.img. Place it in
the root directory of a TFTP server and serve it at
192.168.200.200/24.
2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot
by pressing Enter when prompted. Credentials are identical to the one
in the APs interface. By default it is admin / new2day.
3. Set the bootcmd so the AP can boot OpenWrt by executing
$ setenv boot_openwrt "setenv bootargs;
cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000"
$ setenv bootcmd "run boot_openwrt"
$ saveenv
If you plan on going back to the vendor firmware - the bootcmd for it
is stored in the boot_flash variable.
4. Load the initramfs image to RAM and boot by executing
$ tftpboot 0x1000000 192.168.200.200:
01C8A8C0.img; bootm
5. Make a backup of the "firmware" partition if you ever wish to go back
to the vendor firmware.
6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp
folder.
7. Flash OpenWrt using sysupgrade.
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit
16b01fb1b9c99513c318109bef96a1a3545c57a0)
board=$(board_name)
case "$board" in
+enterasys,ws-ap3710i)
+ echo $(mtd_get_mac_ascii cfg2 RADIOADDR${PHYNBR}) > /sys${DEVPATH}/macaddress
+ ;;
ocedo,panda)
WMAC=wmac$(($PHYNBR + 1))
MAC=$(mtd_get_mac_ascii uboot-env0 ${WMAC})
# CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_WATCHDOG_CORE=y
+# CONFIG_WS_AP3710I is not set
# CONFIG_XES_MPC85xx is not set
# CONFIG_XPS_USB_HCD_XILINX is not set
CONFIG_XZ_DEC_BCJ=y
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later or MIT
+
+/include/ "fsl/p1020si-pre.dtsi"
+/ {
+ model = "Enterasys WS-AP3710i";
+ compatible = "enterasys,ws-ap3710i";
+
+ aliases {
+ led-boot = &led_power_green;
+ led-failsafe = &led_power_red;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_red;
+ label-mac-device = &enet0;
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wifi1 {
+ gpios = <&gpio0 3 0>;
+ label = "ws-ap3710i:green:radio1";
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wifi2 {
+ gpios = <&gpio0 4 0>;
+ label = "ws-ap3710i:green:radio2";
+ linux,default-trigger = "phy1tpt";
+ };
+
+ led_power_green: power_green {
+ gpios = <&gpio0 8 0>;
+ label = "ws-ap3710i:green:power";
+ };
+
+ led_power_red: power_red {
+ gpios = <&gpio0 9 0>;
+ label = "ws-ap3710i:red:power";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ gpios = <&gpio0 1 1>; /* active low */
+ linux,code = <0x198>; /* KEY_RESTART */
+ };
+ };
+
+ lbc: localbus@ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
+ ranges = <0x0 0x0 0x0 0xee000000 0x2000000>;
+
+ nor@0,0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x2000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ compatible = "denx,fit";
+ reg = <0x0 0x1d80000>;
+ label = "firmware";
+ };
+
+ partition@1d80000 {
+ reg = <0x1d80000 0x80000>;
+ label = "u-boot";
+ read-only;
+ };
+
+ partition@1e00000 {
+ reg = <0x1e00000 0x100000>;
+ label = "nvram";
+ read-only;
+ };
+
+ partition@1f00000 {
+ reg = <0x1f00000 0x20000>;
+ label = "cfg2";
+ read-only;
+ };
+
+ partition@1f20000 {
+ reg = <0x1f20000 0x20000>;
+ label = "cfg1";
+ read-only;
+ };
+ };
+ };
+ };
+
+ soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x100000>;
+
+ gpio0: gpio-controller@fc00 {
+ };
+
+ mdio@24000 {
+ phy4: ethernet-phy@4 {
+ reg = <0x4>;
+ reset-gpios = <&gpio0 2 1>;
+ };
+ };
+
+ enet0: ethernet@b0000 {
+ phy-connection-type = "rgmii-id";
+ phy-handle = <&phy4>;
+ };
+
+ enet1: ethernet@b1000 {
+ status = "disabled";
+ };
+
+ enet2: ethernet@b2000 {
+ status = "disabled";
+ };
+
+ usb@22000 {
+ status = "disabled";
+ };
+
+ usb@23000 {
+ status = "disabled";
+ };
+ };
+
+ pci0: pcie@ffe09000 {
+ ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>;
+ reg = <0 0xffe09000 0 0x1000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0xa0000000
+ 0x2000000 0x0 0xa0000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+ pci1: pcie@ffe0a000 {
+ reg = <0 0xffe0a000 0 0x1000>;
+ ranges = <0x2000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000
+ 0x1000000 0x0 0x00000000 0 0xffc00000 0x0 0x10000>;
+ pcie@0 {
+ ranges = <0x2000000 0x0 0x80000000
+ 0x2000000 0x0 0x80000000
+ 0x0 0x20000000
+
+ 0x1000000 0x0 0x0
+ 0x1000000 0x0 0x0
+ 0x0 0x100000>;
+ };
+ };
+
+};
+/include/ "fsl/p1020si-post.dtsi"
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+
+
+/*
+ * Enterasys WS-AP3710i Board Setup
+ *
+ * Copyright (C) 2019 David Bauer <mail@david-bauer.net>
+ *
+ * Based on:
+ * mpc85xx_rdb.c:
+ * MPC85xx RDB Board Setup
+ * Copyright 2013 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/stddef.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/of_platform.h>
+
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <mm/mmu_decl.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+#include "smp.h"
+
+#include "mpc85xx.h"
+
+void __init ws_ap3710i_pic_init(void)
+{
+ struct mpic *mpic;
+
+ mpic = mpic_alloc(NULL, 0,
+ MPIC_BIG_ENDIAN |
+ MPIC_SINGLE_DEST_CPU,
+ 0, 256, " OpenPIC ");
+
+ BUG_ON(mpic == NULL);
+ mpic_init(mpic);
+}
+
+/*
+ * Setup the architecture
+ */
+static void __init ws_ap3710i_setup_arch(void)
+{
+ if (ppc_md.progress)
+ ppc_md.progress("ws_ap3710i_setup_arch()", 0);
+
+ mpc85xx_smp_init();
+
+ fsl_pci_assign_primary();
+
+ pr_info("WS-AP3710i board from Enterasys\n");
+}
+
+machine_arch_initcall(ws_ap3710i, mpc85xx_common_publish_devices);
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init ws_ap3710i_probe(void)
+{
+ if (of_machine_is_compatible("enterasys,ws-ap3710i"))
+ return 1;
+ return 0;
+}
+
+define_machine(ws_ap3710i) {
+ .name = "P1020 RDB",
+ .probe = ws_ap3710i_probe,
+ .setup_arch = ws_ap3710i_setup_arch,
+ .init_IRQ = ws_ap3710i_pic_init,
+#ifdef CONFIG_PCI
+ .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
+ .pcibios_fixup_phb = fsl_pcibios_fixup_phb,
+#endif
+ .get_irq = mpic_get_irq,
+ .calibrate_decr = generic_calibrate_decr,
+ .progress = udbg_progress,
+};
endef
TARGET_DEVICES += hiveap-330
+define Device/ws-ap3710i
+ DEVICE_TITLE := Enterasys WS-AP3710i
+ BLOCKSIZE := 128k
+ KERNEL = kernel-bin | lzma | fit lzma $(KDIR)/image-$$(DEVICE_DTS).dtb
+ SUPPORTED_DEVICES := enterasys,ws-ap3710i
+ IMAGES := sysupgrade.bin
+ IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata
+endef
+TARGET_DEVICES += ws-ap3710i
+
define Device/panda
DEVICE_TITLE := OCEDO Panda
DEVICE_PACKAGES := kmod-rtc-ds1307 uboot-envtools
CONFIG_MTD_NAND_ECC=y
CONFIG_MTD_NAND_FSL_ELBC=y
CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_SPLIT_FIRMWARE=y
+CONFIG_MTD_SPLIT_FIT_FW=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_BEB_LIMIT=20
CONFIG_MTD_UBI_BLOCK=y
CONFIG_UBIFS_FS_ADVANCED_COMPR=y
CONFIG_UBIFS_FS_LZO=y
CONFIG_UBIFS_FS_ZLIB=y
+CONFIG_WS_AP3710I=y
CONFIG_XPS=y
--- /dev/null
+--- a/arch/powerpc/platforms/85xx/Kconfig
++++ b/arch/powerpc/platforms/85xx/Kconfig
+@@ -71,6 +71,17 @@ config PANDA
+ This board is a Concurrent Dual-Band wireless access point with a
+ Freescale P1020 SoC.
+
++config WS_AP3710I
++ bool "Enterasys WS-AP3710i"
++ select DEFAULT_UIMAGE
++ select ARCH_REQUIRE_GPIOLIB
++ select GPIO_MPC8XXX
++ help
++ This option enables support for the Enterasys WS-AP3710i board.
++
++ This board is a Concurrent Dual-Band wireless access point with a
++ Freescale P1020 SoC.
++
+ config MPC8540_ADS
+ bool "Freescale MPC8540 ADS"
+ select DEFAULT_UIMAGE
+--- a/arch/powerpc/platforms/85xx/Makefile
++++ b/arch/powerpc/platforms/85xx/Makefile
+@@ -24,6 +24,7 @@ obj-$(CONFIG_P1022_RDK) += p1022_rdk.o
+ obj-$(CONFIG_P1023_RDB) += p1023_rdb.o
+ obj-$(CONFIG_PANDA) += panda.o
+ obj-$(CONFIG_TWR_P102x) += twr_p102x.o
++obj-$(CONFIG_WS_AP3710I) += ws-ap3710i.o
+ obj-$(CONFIG_CORENET_GENERIC) += corenet_generic.o
+ obj-$(CONFIG_FB_FSL_DIU) += t1042rdb_diu.o
+ obj-$(CONFIG_RED_15W_REV1) += red15w_rev1.o