+++ /dev/null
-CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y
-CONFIG_ARCH_DISCARD_MEMBLOCK=y
-CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_REQUIRE_GPIOLIB=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_AUDIT=y
-CONFIG_AUDIT_GENERIC=y
-CONFIG_B53=y
-CONFIG_B53_MMAP_DRIVER=y
-CONFIG_B53_PHY_DRIVER=y
-CONFIG_B53_PHY_FIXUP=y
-CONFIG_B53_SPI_DRIVER=y
-CONFIG_BCM63XX=y
-CONFIG_BCM63XX_EHCI=y
-CONFIG_BCM63XX_ENET=y
-CONFIG_BCM63XX_OHCI=y
-CONFIG_BCM63XX_PHY=y
-CONFIG_BCM63XX_WDT=y
-CONFIG_BOARD_BCM963XX=y
-# CONFIG_BOARD_LIVEBOX is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_CEVT_R4K=y
-CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200"
-CONFIG_CMDLINE_BOOL=y
-# CONFIG_CMDLINE_OVERRIDE is not set
-CONFIG_CPU_BIG_ENDIAN=y
-CONFIG_CPU_GENERIC_DUMP_TLB=y
-CONFIG_CPU_HAS_PREFETCH=y
-CONFIG_CPU_HAS_SYNC=y
-CONFIG_CPU_MIPS32=y
-CONFIG_CPU_MIPSR1=y
-CONFIG_CPU_R4K_CACHE_TLB=y
-CONFIG_CPU_R4K_FPU=y
-CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y
-CONFIG_CPU_SUPPORTS_HIGHMEM=y
-CONFIG_CSRC_R4K=y
-CONFIG_DECOMPRESS_LZMA=y
-CONFIG_DMA_NONCOHERENT=y
-CONFIG_EARLY_PRINTK=y
-CONFIG_FIRMWARE_IN_KERNEL=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
-CONFIG_GENERIC_CMOS_UPDATE=y
-CONFIG_GENERIC_GPIO=y
-CONFIG_GENERIC_IO=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GPIOLIB=y
-CONFIG_GPIO_74X164=y
-CONFIG_GPIO_SYSFS=y
-# CONFIG_HAMRADIO is not set
-CONFIG_HARDWARE_WATCHPOINTS=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT=y
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_TRANSPARENT_HUGEPAGE=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_API_DEBUG=y
-CONFIG_HAVE_DMA_ATTRS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACE_MCOUNT_TEST=y
-CONFIG_HAVE_GENERIC_DMA_COHERENT=y
-CONFIG_HAVE_GENERIC_HARDIRQS=y
-CONFIG_HAVE_IDE=y
-CONFIG_HAVE_IRQ_WORK=y
-CONFIG_HAVE_MEMBLOCK=y
-CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HW_HAS_PCI=y
-CONFIG_HW_RANDOM=y
-CONFIG_HW_RANDOM_BCM63XX=y
-CONFIG_HZ=250
-# CONFIG_HZ_100 is not set
-CONFIG_HZ_250=y
-CONFIG_IMAGE_CMDLINE_HACK=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_IP_PIMSM_V1=y
-CONFIG_IP_PIMSM_V2=y
-CONFIG_IRQ_CPU=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_LEDS_GPIO=y
-CONFIG_M25PXX_USE_FAST_READ=y
-CONFIG_MDIO_BOARDINFO=y
-CONFIG_MIPS=y
-# CONFIG_MIPS_HUGE_TLB_SUPPORT is not set
-CONFIG_MIPS_L1_CACHE_SHIFT=5
-# CONFIG_MIPS_MACHINE is not set
-CONFIG_MIPS_MT_DISABLED=y
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_MODULE_FORCE_LOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MTD_BCM63XX_PARTS=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_BE_BYTE_SWAP=y
-# CONFIG_MTD_CFI_GEOMETRY is not set
-# CONFIG_MTD_CFI_NOSWAP is not set
-CONFIG_MTD_CFI_STAA=y
-CONFIG_MTD_CMDLINE_PARTS=y
-# CONFIG_MTD_COMPLEX_MAPPINGS is not set
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_M25P80=y
-CONFIG_MTD_PHYSMAP=y
-CONFIG_MTD_REDBOOT_PARTS=y
-CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NO_GENERIC_PCI_IOPORT_MAP=y
-CONFIG_PAGEFLAGS_EXTENDED=y
-CONFIG_PCI=y
-# CONFIG_PCIEAER is not set
-CONFIG_PCIEPORTBUS=y
-CONFIG_PCI_DOMAINS=y
-CONFIG_PERCPU_RWSEM=y
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PHYLIB=y
-CONFIG_POSIX_MQUEUE=y
-CONFIG_POSIX_MQUEUE_SYSCTL=y
-# CONFIG_PREEMPT_RCU is not set
-CONFIG_RELAY=y
-CONFIG_RTL8366_SMI=y
-CONFIG_RTL8367_PHY=y
-# CONFIG_SCSI_DMA is not set
-# CONFIG_SERIAL_8250 is not set
-CONFIG_SERIAL_BCM63XX=y
-CONFIG_SERIAL_BCM63XX_CONSOLE=y
-CONFIG_SPI=y
-CONFIG_SPI_BCM63XX=y
-CONFIG_SPI_BCM63XX_HSSPI=y
-CONFIG_SPI_BITBANG=y
-CONFIG_SPI_GPIO=y
-CONFIG_SPI_MASTER=y
-CONFIG_SQUASHFS_EMBEDDED=y
-CONFIG_SSB=y
-CONFIG_SSB_B43_PCI_BRIDGE=y
-CONFIG_SSB_BLOCKIO=y
-# CONFIG_SSB_DRIVER_MIPS is not set
-CONFIG_SSB_DRIVER_PCICORE=y
-CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
-CONFIG_SSB_PCIHOST=y
-CONFIG_SSB_PCIHOST_POSSIBLE=y
-CONFIG_SSB_SPROM=y
-CONFIG_SWAP_IO_SPACE=y
-CONFIG_SWCONFIG=y
-CONFIG_SYS_HAS_CPU_MIPS32_R1=y
-CONFIG_SYS_HAS_EARLY_PRINTK=y
-CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
-CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
-CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_UIDGID_CONVERTED=y
-CONFIG_USB_ARCH_HAS_XHCI=y
-# CONFIG_USB_HCD_SSB is not set
-CONFIG_USB_SUPPORT=y
-CONFIG_VM_EVENT_COUNTERS=y
-CONFIG_WATCHDOG_NOWAYOUT=y
-CONFIG_ZONE_DMA_FLAG=0
+++ /dev/null
-From 243970ea035623f70431a80ece802f572cd446be Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sun, 9 Dec 2012 00:10:00 +0100
-Subject: [PATCH V2 1/2] spi/bcm63xx: reject transfers unable to transfer
-
-The hardware does not support keeping CS asserted after sending one
-FIFO buffer worth of data, so reject transfers requiring CS being kept
-asserted, either between transers or for a certain time after it,
-or exceeding the FIFO size.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 91 +++++++++++++++++++++------------------------
- 1 file changed, 42 insertions(+), 49 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -49,16 +49,10 @@ struct bcm63xx_spi {
- unsigned int msg_type_shift;
- unsigned int msg_ctl_width;
-
-- /* Data buffers */
-- const unsigned char *tx_ptr;
-- unsigned char *rx_ptr;
--
- /* data iomem */
- u8 __iomem *tx_io;
- const u8 __iomem *rx_io;
-
-- int remaining_bytes;
--
- struct clk *clk;
- struct platform_device *pdev;
- };
-@@ -175,24 +169,13 @@ static int bcm63xx_spi_setup(struct spi_
- return 0;
- }
-
--/* Fill the TX FIFO with as many bytes as possible */
--static void bcm63xx_spi_fill_tx_fifo(struct bcm63xx_spi *bs)
--{
-- u8 size;
--
-- /* Fill the Tx FIFO with as many bytes as possible */
-- size = bs->remaining_bytes < bs->fifo_size ? bs->remaining_bytes :
-- bs->fifo_size;
-- memcpy_toio(bs->tx_io, bs->tx_ptr, size);
-- bs->remaining_bytes -= size;
--}
--
--static unsigned int bcm63xx_txrx_bufs(struct spi_device *spi,
-- struct spi_transfer *t)
-+static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
- {
- struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
- u16 msg_ctl;
- u16 cmd;
-+ u8 rx_tail;
-+ unsigned int timeout = 0;
-
- /* Disable the CMD_DONE interrupt */
- bcm_spi_writeb(bs, 0, SPI_INT_MASK);
-@@ -200,14 +183,8 @@ static unsigned int bcm63xx_txrx_bufs(st
- dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
- t->tx_buf, t->rx_buf, t->len);
-
-- /* Transmitter is inhibited */
-- bs->tx_ptr = t->tx_buf;
-- bs->rx_ptr = t->rx_buf;
--
-- if (t->tx_buf) {
-- bs->remaining_bytes = t->len;
-- bcm63xx_spi_fill_tx_fifo(bs);
-- }
-+ if (t->tx_buf)
-+ memcpy_toio(bs->tx_io, t->tx_buf, t->len);
-
- init_completion(&bs->done);
-
-@@ -239,7 +216,18 @@ static unsigned int bcm63xx_txrx_bufs(st
- /* Enable the CMD_DONE interrupt */
- bcm_spi_writeb(bs, SPI_INTR_CMD_DONE, SPI_INT_MASK);
-
-- return t->len - bs->remaining_bytes;
-+ timeout = wait_for_completion_timeout(&bs->done, HZ);
-+ if (!timeout)
-+ return -ETIMEDOUT;
-+
-+ /* read out all data */
-+ rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
-+
-+ /* Read out all the data */
-+ if (rx_tail)
-+ memcpy_fromio(t->rx_ptr, bs->rx_io, rx_tail);
-+
-+ return 0;
- }
-
- static int bcm63xx_spi_prepare_transfer(struct spi_master *master)
-@@ -267,36 +255,41 @@ static int bcm63xx_spi_transfer_one(stru
- struct spi_transfer *t;
- struct spi_device *spi = m->spi;
- int status = 0;
-- unsigned int timeout = 0;
-
- list_for_each_entry(t, &m->transfers, transfer_list) {
-- unsigned int len = t->len;
-- u8 rx_tail;
--
- status = bcm63xx_spi_check_transfer(spi, t);
- if (status < 0)
- goto exit;
-
-+ /* we can only transfer one fifo worth of data */
-+ if (t->len > bs->fifo_size) {
-+ dev_err(&spi->dev, "unable to do transfers larger than FIFO size (%i > %i)\n",
-+ t->len, bs->fifo_size);
-+ status = -EINVAL;
-+ goto exit;
-+ }
-+
-+ /* CS will be deasserted directly after transfer */
-+ if (t->delay_usecs) {
-+ dev_err(&spi->dev, "unable to keep CS asserted after transfer\n");
-+ status = -EINVAL;
-+ goto exit;
-+ }
-+
-+ if (!t->cs_change &&
-+ !list_is_last(&t->transfer_list, &m->transfers)) {
-+ dev_err(&spi->dev, "unable to keep CS asserted between transfers\n");
-+ status = -EINVAL;
-+ goto exit;
-+ }
-+
- /* configure adapter for a new transfer */
- bcm63xx_spi_setup_transfer(spi, t);
-
-- while (len) {
-- /* send the data */
-- len -= bcm63xx_txrx_bufs(spi, t);
--
-- timeout = wait_for_completion_timeout(&bs->done, HZ);
-- if (!timeout) {
-- status = -ETIMEDOUT;
-- goto exit;
-- }
--
-- /* read out all data */
-- rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
--
-- /* Read out all the data */
-- if (rx_tail)
-- memcpy_fromio(bs->rx_ptr, bs->rx_io, rx_tail);
-- }
-+ /* send the data */
-+ status = bcm63xx_txrx_bufs(spi, t);
-+ if (status)
-+ goto exit;
-
- m->actual_length += t->len;
- }
+++ /dev/null
-From 725e81d507b1098cd275d4e3333c77c4b750fa79 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sun, 9 Dec 2012 01:53:05 +0100
-Subject: [PATCH V2 2/2] spi/bcm63xx: work around inability to keep CS up
-
-This SPI controller does not support keeping CS asserted after sending
-a transfer.
-Since messages expected on this SPI controller are rather short, we can
-work around it for normal use cases by sending all transfers at once in
-a big full duplex stream.
-
-This means that we cannot change the speed between transfers if they
-require CS to be kept asserted, but these would have been rejected
-before anyway because of the inability of keeping CS asserted.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
-V1 -> V2:
- * split out rejection logic into separate patch
- * fixed return type of bcm63xx_txrx_bufs()
- * slightly reworked bcm63xx_txrx_bufs, obsoleting one local variable
-
- drivers/spi/spi-bcm63xx.c | 134 +++++++++++++++++++++++++++++++++++----------
- 1 file changed, 106 insertions(+), 28 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -37,6 +37,8 @@
-
- #define PFX KBUILD_MODNAME
-
-+#define BCM63XX_SPI_MAX_PREPEND 15
-+
- struct bcm63xx_spi {
- struct completion done;
-
-@@ -169,13 +171,17 @@ static int bcm63xx_spi_setup(struct spi_
- return 0;
- }
-
--static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
-+static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *first,
-+ unsigned int num_transfers)
- {
- struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
- u16 msg_ctl;
- u16 cmd;
- u8 rx_tail;
-- unsigned int timeout = 0;
-+ unsigned int i, timeout = 0, prepend_len = 0, len = 0;
-+ struct spi_transfer *t = first;
-+ bool do_rx = false;
-+ bool do_tx = false;
-
- /* Disable the CMD_DONE interrupt */
- bcm_spi_writeb(bs, 0, SPI_INT_MASK);
-@@ -183,19 +189,45 @@ static int bcm63xx_txrx_bufs(struct spi_
- dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n",
- t->tx_buf, t->rx_buf, t->len);
-
-- if (t->tx_buf)
-- memcpy_toio(bs->tx_io, t->tx_buf, t->len);
-+ if (num_transfers > 1 && t->tx_buf && t->len <= BCM63XX_SPI_MAX_PREPEND)
-+ prepend_len = t->len;
-+
-+ /* prepare the buffer */
-+ for (i = 0; i < num_transfers; i++) {
-+ if (t->tx_buf) {
-+ do_tx = true;
-+ memcpy_toio(bs->tx_io + len, t->tx_buf, t->len);
-+
-+ /* don't prepend more than one tx */
-+ if (t != first)
-+ prepend_len = 0;
-+ }
-+
-+ if (t->rx_buf) {
-+ do_rx = true;
-+ /* prepend is half-duplex write only */
-+ if (t == first)
-+ prepend_len = 0;
-+ }
-+
-+ len += t->len;
-+
-+ t = list_entry(t->transfer_list.next, struct spi_transfer,
-+ transfer_list);
-+ }
-+
-+ len -= prepend_len;
-
- init_completion(&bs->done);
-
- /* Fill in the Message control register */
-- msg_ctl = (t->len << SPI_BYTE_CNT_SHIFT);
-+ msg_ctl = (len << SPI_BYTE_CNT_SHIFT);
-
-- if (t->rx_buf && t->tx_buf)
-+ if (do_rx && do_tx && prepend_len == 0)
- msg_ctl |= (SPI_FD_RW << bs->msg_type_shift);
-- else if (t->rx_buf)
-+ else if (do_rx)
- msg_ctl |= (SPI_HD_R << bs->msg_type_shift);
-- else if (t->tx_buf)
-+ else if (do_tx)
- msg_ctl |= (SPI_HD_W << bs->msg_type_shift);
-
- switch (bs->msg_ctl_width) {
-@@ -209,7 +241,7 @@ static int bcm63xx_txrx_bufs(struct spi_
-
- /* Issue the transfer */
- cmd = SPI_CMD_START_IMMEDIATE;
-- cmd |= (0 << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
-+ cmd |= (prepend_len << SPI_CMD_PREPEND_BYTE_CNT_SHIFT);
- cmd |= (spi->chip_select << SPI_CMD_DEVICE_ID_SHIFT);
- bcm_spi_writew(bs, cmd, SPI_CMD);
-
-@@ -223,9 +255,25 @@ static int bcm63xx_txrx_bufs(struct spi_
- /* read out all data */
- rx_tail = bcm_spi_readb(bs, SPI_RX_TAIL);
-
-+ if (do_rx && rx_tail != len)
-+ return -EIO;
-+
-+ if (!rx_tail)
-+ return 0;
-+
-+ len = 0;
-+ t = first;
- /* Read out all the data */
-- if (rx_tail)
-- memcpy_fromio(t->rx_ptr, bs->rx_io, rx_tail);
-+ for (i = 0; i < num_transfers; i++) {
-+ if (t->rx_buf)
-+ memcpy_fromio(t->rx_buf, bs->rx_io + len, t->len);
-+
-+ if (t != first || prepend_len == 0)
-+ len += t->len;
-+
-+ t = list_entry(t->transfer_list.next, struct spi_transfer,
-+ transfer_list);
-+ }
-
- return 0;
- }
-@@ -252,46 +300,76 @@ static int bcm63xx_spi_transfer_one(stru
- struct spi_message *m)
- {
- struct bcm63xx_spi *bs = spi_master_get_devdata(master);
-- struct spi_transfer *t;
-+ struct spi_transfer *t, *first = NULL;
- struct spi_device *spi = m->spi;
- int status = 0;
-+ unsigned int n_transfers = 0, total_len = 0;
-+ bool can_use_prepend = false;
-
-+ /*
-+ * This SPI controller does not support keeping CS active after a
-+ * transfer.
-+ * Work around this by merging as many transfers we can into one big
-+ * full-duplex transfers.
-+ */
- list_for_each_entry(t, &m->transfers, transfer_list) {
- status = bcm63xx_spi_check_transfer(spi, t);
- if (status < 0)
- goto exit;
-
-+ if (!first)
-+ first = t;
-+
-+ n_transfers++;
-+ total_len += t->len;
-+
-+ if (n_transfers == 2 && !first->rx_buf && !t->tx_buf &&
-+ first->len <= BCM63XX_SPI_MAX_PREPEND)
-+ can_use_prepend = true;
-+ else if (can_use_prepend && t->tx_buf)
-+ can_use_prepend = false;
-+
- /* we can only transfer one fifo worth of data */
-- if (t->len > bs->fifo_size) {
-+ if ((can_use_prepend &&
-+ total_len > (bs->fifo_size + BCM63XX_SPI_MAX_PREPEND)) ||
-+ (!can_use_prepend && total_len > bs->fifo_size)) {
- dev_err(&spi->dev, "unable to do transfers larger than FIFO size (%i > %i)\n",
-- t->len, bs->fifo_size);
-+ total_len, bs->fifo_size);
- status = -EINVAL;
- goto exit;
- }
-
-- /* CS will be deasserted directly after transfer */
-- if (t->delay_usecs) {
-- dev_err(&spi->dev, "unable to keep CS asserted after transfer\n");
-+ /* all combined transfers have to have the same speed */
-+ if (t->speed_hz != first->speed_hz) {
-+ dev_err(&spi->dev, "unable to change speed between transfers\n");
- status = -EINVAL;
- goto exit;
- }
-
-- if (!t->cs_change &&
-- !list_is_last(&t->transfer_list, &m->transfers)) {
-- dev_err(&spi->dev, "unable to keep CS asserted between transfers\n");
-+ /* CS will be deasserted directly after transfer */
-+ if (t->delay_usecs) {
-+ dev_err(&spi->dev, "unable to keep CS asserted after transfer\n");
- status = -EINVAL;
- goto exit;
- }
-
-- /* configure adapter for a new transfer */
-- bcm63xx_spi_setup_transfer(spi, t);
--
-- /* send the data */
-- status = bcm63xx_txrx_bufs(spi, t);
-- if (status)
-- goto exit;
--
-- m->actual_length += t->len;
-+ if (t->cs_change ||
-+ list_is_last(&t->transfer_list, &m->transfers)) {
-+ /* configure adapter for a new transfer */
-+ bcm63xx_spi_setup_transfer(spi, first);
-+
-+ /* send the data */
-+ status = bcm63xx_txrx_bufs(spi, first, n_transfers);
-+ if (status)
-+ goto exit;
-+
-+ m->actual_length += total_len;
-+
-+ first = NULL;
-+ n_transfers = 0;
-+ total_len = 0;
-+ can_use_prepend = false;
-+ }
- }
- exit:
- m->status = status;
+++ /dev/null
-From 2a26efda4d16f7d25f1c55e5c387fa3d7d18e9af Mon Sep 17 00:00:00 2001
-From: Kevin Cernekee <cernekee@gmail.com>
-Date: Sat, 14 Jul 2012 23:25:03 -0700
-Subject: [PATCH 01/12] spi/bcm63xx: Remove unused variable
-
-This fixes the following warning:
-
-drivers/spi/spi-bcm63xx.c: In function 'bcm63xx_spi_setup':
-drivers/spi/spi-bcm63xx.c:157:6: warning: unused variable 'ret'
-
-Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
----
- drivers/spi/spi-bcm63xx.c | 1 -
- 1 file changed, 1 deletion(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -152,7 +152,6 @@ static void bcm63xx_spi_setup_transfer(s
- static int bcm63xx_spi_setup(struct spi_device *spi)
- {
- struct bcm63xx_spi *bs;
-- int ret;
-
- bs = spi_master_get_devdata(spi->master);
-
+++ /dev/null
-From f32b46ec9c307753e2418a0f5df1b5cd066b1394 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 11 Mar 2013 13:27:43 +0100
-Subject: [PATCH 02/12] spi/bcm63xx: don't disable non enabled clocks in probe
- error path
-
-When msg_ctl_width is set to an invalid value we try to disable the
-clock despite it never being enabled. Fix it by jumping to the correct
-label.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -489,7 +489,7 @@ static int bcm63xx_spi_probe(struct plat
- default:
- dev_err(dev, "unsupported MSG_CTL width: %d\n",
- bs->msg_ctl_width);
-- goto out_clk_disable;
-+ goto out_err;
- }
-
- /* Initialize hardware */
+++ /dev/null
-From e504d3ed9b35f43e61cf239b103667d87cd7bf3c Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 10 Sep 2012 01:26:55 +0200
-Subject: [PATCH 03/12] spi/bcm63xx: properly prepare clocks before enabling
- them
-
-Use proper clk_prepare/unprepare calls in preparation for switching
-to the generic clock framework.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 10 +++++-----
- 1 file changed, 5 insertions(+), 5 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -493,7 +493,7 @@ static int bcm63xx_spi_probe(struct plat
- }
-
- /* Initialize hardware */
-- clk_enable(bs->clk);
-+ clk_prepare_enable(bs->clk);
- bcm_spi_writeb(bs, SPI_INTR_CLEAR_ALL, SPI_INT_STATUS);
-
- /* register and we are done */
-@@ -509,7 +509,7 @@ static int bcm63xx_spi_probe(struct plat
- return 0;
-
- out_clk_disable:
-- clk_disable(clk);
-+ clk_disable_unprepare(clk);
- out_err:
- platform_set_drvdata(pdev, NULL);
- spi_master_put(master);
-@@ -530,7 +530,7 @@ static int bcm63xx_spi_remove(struct pla
- bcm_spi_writeb(bs, 0, SPI_INT_MASK);
-
- /* HW shutdown */
-- clk_disable(bs->clk);
-+ clk_disable_unprepare(bs->clk);
- clk_put(bs->clk);
-
- platform_set_drvdata(pdev, 0);
-@@ -549,7 +549,7 @@ static int bcm63xx_spi_suspend(struct de
-
- spi_master_suspend(master);
-
-- clk_disable(bs->clk);
-+ clk_disable_unprepare(bs->clk);
-
- return 0;
- }
-@@ -560,7 +560,7 @@ static int bcm63xx_spi_resume(struct dev
- platform_get_drvdata(to_platform_device(dev));
- struct bcm63xx_spi *bs = spi_master_get_devdata(master);
-
-- clk_enable(bs->clk);
-+ clk_prepare_enable(bs->clk);
-
- spi_master_resume(master);
-
+++ /dev/null
-From 3abf34d4e0460bb098fabe3cc8207108bae1905a Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 11 Mar 2013 13:40:26 +0100
-Subject: [PATCH 04/12] spi/bcm63xx: remove duplicated mode bits check
-
-The spi subsystem already checks the mode bits before calling setup.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 6 ------
- 1 file changed, 6 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -158,12 +158,6 @@ static int bcm63xx_spi_setup(struct spi_
- if (!spi->bits_per_word)
- spi->bits_per_word = 8;
-
-- if (spi->mode & ~MODEBITS) {
-- dev_err(&spi->dev, "%s, unsupported mode bits %x\n",
-- __func__, spi->mode & ~MODEBITS);
-- return -EINVAL;
-- }
--
- dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec/bit\n",
- __func__, spi->mode & MODEBITS, spi->bits_per_word, 0);
-
+++ /dev/null
-From ee18b0ac561afb9dd7d87a4217e80151a7e29dfc Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 11 Mar 2013 13:42:22 +0100
-Subject: [PATCH 05/12] spi/bcm63xx: remove unneeded debug message
-
-The spi subsystem already provides this info in a more extensive
-debug print except for the nsecs/bit - which wasn't calculated anyway
-and fixed to 0.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 3 ---
- 1 file changed, 3 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -158,9 +158,6 @@ static int bcm63xx_spi_setup(struct spi_
- if (!spi->bits_per_word)
- spi->bits_per_word = 8;
-
-- dev_dbg(&spi->dev, "%s, mode %d, %u bits/w, %u nsec/bit\n",
-- __func__, spi->mode & MODEBITS, spi->bits_per_word, 0);
--
- return 0;
- }
-
+++ /dev/null
-From 30151fe21befa84d9cd27d63f1bf3973988c811e Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 11 Mar 2013 13:47:19 +0100
-Subject: [PATCH 06/12] spi/bcm63xx: remove unused variable bs from
- bcm63xx_spi_setup
-
-It is only written, but never read.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 4 ----
- 1 file changed, 4 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -151,10 +151,6 @@ static void bcm63xx_spi_setup_transfer(s
-
- static int bcm63xx_spi_setup(struct spi_device *spi)
- {
-- struct bcm63xx_spi *bs;
--
-- bs = spi_master_get_devdata(spi->master);
--
- if (!spi->bits_per_word)
- spi->bits_per_word = 8;
-
+++ /dev/null
-From 13a364be644ed9b4666d452756556bb98afdcc56 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 11 Mar 2013 13:48:27 +0100
-Subject: [PATCH 07/12] spi/bcm63xx: check spi bits_per_word in spi_setup
-
-Instead of fixing up the bits_per_word (which the spi subsystem already
-does for us), check it for supported values.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 7 +++++--
- 1 file changed, 5 insertions(+), 2 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -151,8 +151,11 @@ static void bcm63xx_spi_setup_transfer(s
-
- static int bcm63xx_spi_setup(struct spi_device *spi)
- {
-- if (!spi->bits_per_word)
-- spi->bits_per_word = 8;
-+ if (spi->bits_per_word != 8) {
-+ dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
-+ __func__, spi->bits_per_word);
-+ return -EINVAL;
-+ }
-
- return 0;
- }
+++ /dev/null
-From d69ac73da38f0d16cc6b4524cd734b907db6eab8 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 11 Mar 2013 13:51:10 +0100
-Subject: [PATCH 08/12] spi/bcm63xx: simplify bcm63xx_spi_check_transfer
-
-bcm63xx_spi_check_transfer is only called from one place that has
-t always set, so directly check the transfer's bits_per_word.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 7 ++-----
- 1 file changed, 2 insertions(+), 5 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -96,12 +96,9 @@ static const unsigned bcm63xx_spi_freq_t
- static int bcm63xx_spi_check_transfer(struct spi_device *spi,
- struct spi_transfer *t)
- {
-- u8 bits_per_word;
--
-- bits_per_word = (t) ? t->bits_per_word : spi->bits_per_word;
-- if (bits_per_word != 8) {
-+ if (t->bits_per_word != 8) {
- dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
-- __func__, bits_per_word);
-+ __func__, t->bits_per_word);
- return -EINVAL;
- }
-
+++ /dev/null
-From 9c5a988562468823a5e2973f04134a8bd97e7718 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 11 Mar 2013 13:53:16 +0100
-Subject: [PATCH 09/12] spi/bcm63xx: remove spi chip select validity check
-
-The check would belong in bcm63xx_spi_setup if the spi subsystem
-weren't already doing the check for us, so just drop it.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 6 ------
- 1 file changed, 6 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -102,12 +102,6 @@ static int bcm63xx_spi_check_transfer(st
- return -EINVAL;
- }
-
-- if (spi->chip_select > spi->master->num_chipselect) {
-- dev_err(&spi->dev, "%s, unsupported slave %d\n",
-- __func__, spi->chip_select);
-- return -EINVAL;
-- }
--
- return 0;
- }
-
+++ /dev/null
-From 3fffc5f76c830c375692a67948734168ee4c516a Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 11 Mar 2013 13:59:30 +0100
-Subject: [PATCH 10/12] spi/bcm63xx: inline bcm63xx_spi_check_transfer
-
-It only does one check, so just do the check directly in the caller.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 19 +++++--------------
- 1 file changed, 5 insertions(+), 14 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -93,18 +93,6 @@ static const unsigned bcm63xx_spi_freq_t
- { 391000, SPI_CLK_0_391MHZ }
- };
-
--static int bcm63xx_spi_check_transfer(struct spi_device *spi,
-- struct spi_transfer *t)
--{
-- if (t->bits_per_word != 8) {
-- dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
-- __func__, t->bits_per_word);
-- return -EINVAL;
-- }
--
-- return 0;
--}
--
- static void bcm63xx_spi_setup_transfer(struct spi_device *spi,
- struct spi_transfer *t)
- {
-@@ -293,9 +281,12 @@ static int bcm63xx_spi_transfer_one(stru
- * full-duplex transfers.
- */
- list_for_each_entry(t, &m->transfers, transfer_list) {
-- status = bcm63xx_spi_check_transfer(spi, t);
-- if (status < 0)
-+ if (t->bits_per_word != 8) {
-+ dev_err(&spi->dev, "%s, unsupported bits_per_word=%d\n",
-+ __func__, t->bits_per_word);
-+ status = -EINVAL;
- goto exit;
-+ }
-
- if (!first)
- first = t;
+++ /dev/null
-From 2646be877afc663d1688a2add8386b027c9d7e31 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 11 Mar 2013 14:08:06 +0100
-Subject: [PATCH 11/12] spi/bcm63xx: inline hz usage in
- bcm63xx_spi_setup_transfer
-
-bcm63xx_spi_setup_transfer is called from only one place, and that has
-t always set, to hz will always be t->speed_hz - just use it directly in
-the two places instead of moving it in a local variable.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 7 ++-----
- 1 file changed, 2 insertions(+), 5 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -97,15 +97,12 @@ static void bcm63xx_spi_setup_transfer(s
- struct spi_transfer *t)
- {
- struct bcm63xx_spi *bs = spi_master_get_devdata(spi->master);
-- u32 hz;
- u8 clk_cfg, reg;
- int i;
-
-- hz = (t) ? t->speed_hz : spi->max_speed_hz;
--
- /* Find the closest clock configuration */
- for (i = 0; i < SPI_CLK_MASK; i++) {
-- if (hz >= bcm63xx_spi_freq_table[i][0]) {
-+ if (t->speed_hz >= bcm63xx_spi_freq_table[i][0]) {
- clk_cfg = bcm63xx_spi_freq_table[i][1];
- break;
- }
-@@ -122,7 +119,7 @@ static void bcm63xx_spi_setup_transfer(s
-
- bcm_spi_writeb(bs, reg, SPI_CLK_CFG);
- dev_dbg(&spi->dev, "Setting clock register to %02x (hz %d)\n",
-- clk_cfg, hz);
-+ clk_cfg, t->speed_hz);
- }
-
- /* the spi->mode bits understood by this driver: */
+++ /dev/null
-From 95af2d7751d31ea07b7a0d8ec7030f6c62df0ae2 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 11 Mar 2013 14:20:33 +0100
-Subject: [PATCH 12/12] spi/bcm63xx: use devm_ioremap_resource()
-
-Use devm_ioremap_resource() which provides its own error messages.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/spi/spi-bcm63xx.c | 15 +++------------
- 1 file changed, 3 insertions(+), 12 deletions(-)
-
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -412,18 +412,9 @@ static int bcm63xx_spi_probe(struct plat
- platform_set_drvdata(pdev, master);
- bs->pdev = pdev;
-
-- if (!devm_request_mem_region(&pdev->dev, r->start,
-- resource_size(r), PFX)) {
-- dev_err(dev, "iomem request failed\n");
-- ret = -ENXIO;
-- goto out_err;
-- }
--
-- bs->regs = devm_ioremap_nocache(&pdev->dev, r->start,
-- resource_size(r));
-- if (!bs->regs) {
-- dev_err(dev, "unable to ioremap regs\n");
-- ret = -ENOMEM;
-+ bs->regs = devm_ioremap_resource(&pdev->dev, r);
-+ if (IS_ERR(bs->regs)) {
-+ ret = PTR_ERR(bs->regs);
- goto out_err;
- }
-
+++ /dev/null
-From 5ff6b05a18295fa7e03de0fdf32d681a90b69df5 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sat, 30 Mar 2013 10:26:55 +0100
-Subject: [PATCH] spi/bcm63xx: remove unused speed_hz member variable
-
-speed_hz is a write only member, so we can safely remove it and its
-generation. Also fixes the missing clk_put after getting the periph
-clock.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/dev-spi.c | 11 -----------
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h | 1 -
- drivers/spi/spi-bcm63xx.c | 2 --
- 3 files changed, 14 deletions(-)
-
---- a/arch/mips/bcm63xx/dev-spi.c
-+++ b/arch/mips/bcm63xx/dev-spi.c
-@@ -85,20 +85,9 @@ static struct platform_device bcm63xx_sp
-
- int __init bcm63xx_spi_register(void)
- {
-- struct clk *periph_clk;
--
- if (BCMCPU_IS_6328() || BCMCPU_IS_6345())
- return -ENODEV;
-
-- periph_clk = clk_get(NULL, "periph");
-- if (IS_ERR(periph_clk)) {
-- pr_err("unable to get periph clock\n");
-- return -ENODEV;
-- }
--
-- /* Set bus frequency */
-- spi_pdata.speed_hz = clk_get_rate(periph_clk);
--
- spi_resources[0].start = bcm63xx_regset_address(RSET_SPI);
- spi_resources[0].end = spi_resources[0].start;
- spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI);
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
-@@ -13,7 +13,6 @@ struct bcm63xx_spi_pdata {
- unsigned int msg_ctl_width;
- int bus_num;
- int num_chipselect;
-- u32 speed_hz;
- };
-
- enum bcm63xx_regs_spi {
---- a/drivers/spi/spi-bcm63xx.c
-+++ b/drivers/spi/spi-bcm63xx.c
-@@ -46,7 +46,6 @@ struct bcm63xx_spi {
- int irq;
-
- /* Platform data */
-- u32 speed_hz;
- unsigned fifo_size;
- unsigned int msg_type_shift;
- unsigned int msg_ctl_width;
-@@ -436,7 +435,6 @@ static int bcm63xx_spi_probe(struct plat
- master->unprepare_transfer_hardware = bcm63xx_spi_unprepare_transfer;
- master->transfer_one_message = bcm63xx_spi_transfer_one;
- master->mode_bits = MODEBITS;
-- bs->speed_hz = pdata->speed_hz;
- bs->msg_type_shift = pdata->msg_type_shift;
- bs->msg_ctl_width = pdata->msg_ctl_width;
- bs->tx_io = (u8 *)(bs->regs + bcm63xx_spireg(SPI_MSG_DATA));
+++ /dev/null
-From 152addd3a965759b69fbdb9a76526f1f5070bc9a Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Tue, 12 Feb 2013 22:00:10 +0100
-Subject: [PATCH] MIPS: BCM63XX: make nvram checksum failure non fatal
-MIME-Version: 1.0
-Content-Type: text/plain; charset=UTF-8
-Content-Transfer-Encoding: 8bit
-
-Some vendors modify the nvram layout moving the checksum to a different
-place or dropping entirely, so reduce the checksum failure to a warning.
-
-Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
-
-I'm not sure if it should be that "loud" (pr_warn) because users can't
-actually do anything to fix it, so maybe pr_debug would be fine, too.
-
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 5 +----
- arch/mips/bcm63xx/nvram.c | 7 +++----
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h | 4 +---
- 3 files changed, 5 insertions(+), 11 deletions(-)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -745,10 +745,7 @@ void __init board_prom_init(void)
- strcpy(cfe_version, "unknown");
- printk(KERN_INFO PFX "CFE version: %s\n", cfe_version);
-
-- if (bcm63xx_nvram_init(boot_addr + BCM963XX_NVRAM_OFFSET)) {
-- printk(KERN_ERR PFX "invalid nvram checksum\n");
-- return;
-- }
-+ bcm63xx_nvram_init(boot_addr + BCM963XX_NVRAM_OFFSET);
-
- board_name = bcm63xx_nvram_get_name();
- /* find board by name */
---- a/arch/mips/bcm63xx/nvram.c
-+++ b/arch/mips/bcm63xx/nvram.c
-@@ -38,7 +38,7 @@ struct bcm963xx_nvram {
- static struct bcm963xx_nvram nvram;
- static int mac_addr_used;
-
--int __init bcm63xx_nvram_init(void *addr)
-+void __init bcm63xx_nvram_init(void *addr)
- {
- unsigned int check_len;
- u32 crc, expected_crc;
-@@ -60,9 +60,8 @@ int __init bcm63xx_nvram_init(void *addr
- crc = crc32_le(~0, (u8 *)&nvram, check_len);
-
- if (crc != expected_crc)
-- return -EINVAL;
--
-- return 0;
-+ pr_warn("nvram checksum failed, contents may be invalid (expected %08x, got %08x)\n",
-+ expected_crc, crc);
- }
-
- u8 *bcm63xx_nvram_get_name(void)
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h
-@@ -9,10 +9,8 @@
- *
- * Initialized the local nvram copy from the target address and checks
- * its checksum.
-- *
-- * Returns 0 on success.
- */
--int __init bcm63xx_nvram_init(void *nvram);
-+void bcm63xx_nvram_init(void *nvram);
-
- /**
- * bcm63xx_nvram_get_name() - returns the board name according to nvram
+++ /dev/null
-From 76d82677cb010b28346aa4c7aa9d36d94916392b Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Tue, 8 May 2012 09:39:01 +0200
-Subject: [PATCH] Revert "MIPS: BCM63XX: Call board_register_device from
- device_initcall()"
-
-This commit causes a race between PCI scan and SSB fallback SPROM handler
-registration, causing the wifi to not work on slower systems. The only
-subsystem touched from board_register_devices is platform device
-registration, which is safe as an arch init call.
-
-This reverts commit d64ed7ada2f689d2c62af1892ca55e47d3653e36.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
-
-This patch is in OpenWrt since ages, and we never encountered any issues
-from this revert.
-
- arch/mips/bcm63xx/setup.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
---- a/arch/mips/bcm63xx/setup.c
-+++ b/arch/mips/bcm63xx/setup.c
-@@ -157,4 +157,4 @@ int __init bcm63xx_register_devices(void
- return board_register_devices();
- }
-
--device_initcall(bcm63xx_register_devices);
-+arch_initcall(bcm63xx_register_devices);
+++ /dev/null
-From 715d03e5409fac9cbe76fd802db49ca15158378f Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sat, 30 Mar 2013 20:31:48 +0100
-Subject: [PATCH] MIPS: BCM63XX: merge bcm63xx_clk.h into bcm63xx/clk.c
-
-All the header file does is provide the internal structure of clk,
-which shouldn't be used by anyone except clk.c itself anyway.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/clk.c | 8 +++++++-
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_clk.h | 11 -----------
- drivers/tty/serial/bcm63xx_uart.c | 1 -
- 3 files changed, 7 insertions(+), 13 deletions(-)
- delete mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_clk.h
-
---- a/arch/mips/bcm63xx/clk.c
-+++ b/arch/mips/bcm63xx/clk.c
-@@ -15,7 +15,13 @@
- #include <bcm63xx_io.h>
- #include <bcm63xx_regs.h>
- #include <bcm63xx_reset.h>
--#include <bcm63xx_clk.h>
-+
-+struct clk {
-+ void (*set)(struct clk *, int);
-+ unsigned int rate;
-+ unsigned int usage;
-+ int id;
-+};
-
- static DEFINE_MUTEX(clocks_mutex);
-
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_clk.h
-+++ /dev/null
-@@ -1,11 +0,0 @@
--#ifndef BCM63XX_CLK_H_
--#define BCM63XX_CLK_H_
--
--struct clk {
-- void (*set)(struct clk *, int);
-- unsigned int rate;
-- unsigned int usage;
-- int id;
--};
--
--#endif /* ! BCM63XX_CLK_H_ */
---- a/drivers/tty/serial/bcm63xx_uart.c
-+++ b/drivers/tty/serial/bcm63xx_uart.c
-@@ -30,7 +30,6 @@
- #include <linux/serial.h>
- #include <linux/serial_core.h>
-
--#include <bcm63xx_clk.h>
- #include <bcm63xx_irq.h>
- #include <bcm63xx_regs.h>
- #include <bcm63xx_io.h>
+++ /dev/null
-From 80b0356aea30e9fc9e075d31c2bf37e7cbfea8c9 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sun, 10 Mar 2013 13:59:55 +0100
-Subject: [PATCH 1/3] bcm63xx_enet: use managed io memory allocations
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/net/ethernet/broadcom/bcm63xx_enet.c | 43 +++++---------------------
- 1 file changed, 7 insertions(+), 36 deletions(-)
-
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-@@ -1620,7 +1620,6 @@ static int bcm_enet_probe(struct platfor
- struct resource *res_mem, *res_irq, *res_irq_rx, *res_irq_tx;
- struct mii_bus *bus;
- const char *clk_name;
-- unsigned int iomem_size;
- int i, ret;
-
- /* stop if shared driver failed, assume driver->probe will be
-@@ -1645,17 +1644,12 @@ static int bcm_enet_probe(struct platfor
- if (ret)
- goto out;
-
-- iomem_size = resource_size(res_mem);
-- if (!request_mem_region(res_mem->start, iomem_size, "bcm63xx_enet")) {
-- ret = -EBUSY;
-- goto out;
-- }
--
-- priv->base = ioremap(res_mem->start, iomem_size);
-+ priv->base = devm_request_and_ioremap(&pdev->dev, res_mem);
- if (priv->base == NULL) {
- ret = -ENOMEM;
-- goto out_release_mem;
-+ goto out;
- }
-+
- dev->irq = priv->irq = res_irq->start;
- priv->irq_rx = res_irq_rx->start;
- priv->irq_tx = res_irq_tx->start;
-@@ -1675,7 +1669,7 @@ static int bcm_enet_probe(struct platfor
- priv->mac_clk = clk_get(&pdev->dev, clk_name);
- if (IS_ERR(priv->mac_clk)) {
- ret = PTR_ERR(priv->mac_clk);
-- goto out_unmap;
-+ goto out;
- }
- clk_enable(priv->mac_clk);
-
-@@ -1815,12 +1809,6 @@ out_uninit_hw:
- out_put_clk_mac:
- clk_disable(priv->mac_clk);
- clk_put(priv->mac_clk);
--
--out_unmap:
-- iounmap(priv->base);
--
--out_release_mem:
-- release_mem_region(res_mem->start, iomem_size);
- out:
- free_netdev(dev);
- return ret;
-@@ -1834,7 +1822,6 @@ static int bcm_enet_remove(struct platfo
- {
- struct bcm_enet_priv *priv;
- struct net_device *dev;
-- struct resource *res;
-
- /* stop netdevice */
- dev = platform_get_drvdata(pdev);
-@@ -1857,11 +1844,6 @@ static int bcm_enet_remove(struct platfo
- bcm_enet_mdio_write_mii);
- }
-
-- /* release device resources */
-- iounmap(priv->base);
-- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-- release_mem_region(res->start, resource_size(res));
--
- /* disable hw block clocks */
- if (priv->phy_clk) {
- clk_disable(priv->phy_clk);
-@@ -1890,31 +1872,20 @@ struct platform_driver bcm63xx_enet_driv
- static int bcm_enet_shared_probe(struct platform_device *pdev)
- {
- struct resource *res;
-- unsigned int iomem_size;
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- if (!res)
- return -ENODEV;
-
-- iomem_size = resource_size(res);
-- if (!request_mem_region(res->start, iomem_size, "bcm63xx_enet_dma"))
-- return -EBUSY;
--
-- bcm_enet_shared_base = ioremap(res->start, iomem_size);
-- if (!bcm_enet_shared_base) {
-- release_mem_region(res->start, iomem_size);
-+ bcm_enet_shared_base = devm_request_and_ioremap(&pdev->dev, res);
-+ if (!bcm_enet_shared_base)
- return -ENOMEM;
-- }
-+
- return 0;
- }
-
- static int bcm_enet_shared_remove(struct platform_device *pdev)
- {
-- struct resource *res;
--
-- iounmap(bcm_enet_shared_base);
-- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-- release_mem_region(res->start, resource_size(res));
- return 0;
- }
-
+++ /dev/null
-From 451a609ca472f80838df056689359c5486d832c1 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sun, 10 Mar 2013 14:05:01 +0100
-Subject: [PATCH 2/3] bcm63xx_enet: use managed memory allocations
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/net/ethernet/broadcom/bcm63xx_enet.c | 8 +++-----
- 1 file changed, 3 insertions(+), 5 deletions(-)
-
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-@@ -1728,7 +1728,8 @@ static int bcm_enet_probe(struct platfor
- * if a slave is not present on hw */
- bus->phy_mask = ~(1 << priv->phy_id);
-
-- bus->irq = kmalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL);
-+ bus->irq = devm_kzalloc(&pdev->dev, sizeof(int) * PHY_MAX_ADDR,
-+ GFP_KERNEL);
- if (!bus->irq) {
- ret = -ENOMEM;
- goto out_free_mdio;
-@@ -1789,10 +1790,8 @@ static int bcm_enet_probe(struct platfor
- return 0;
-
- out_unregister_mdio:
-- if (priv->mii_bus) {
-+ if (priv->mii_bus)
- mdiobus_unregister(priv->mii_bus);
-- kfree(priv->mii_bus->irq);
-- }
-
- out_free_mdio:
- if (priv->mii_bus)
-@@ -1833,7 +1832,6 @@ static int bcm_enet_remove(struct platfo
-
- if (priv->has_phy) {
- mdiobus_unregister(priv->mii_bus);
-- kfree(priv->mii_bus->irq);
- mdiobus_free(priv->mii_bus);
- } else {
- struct bcm63xx_enet_platform_data *pd;
+++ /dev/null
-From 8d6b746129f11efe4ba69aeb2c982359d33c6ec3 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 10 Sep 2012 01:28:47 +0200
-Subject: [PATCH 3/3] bcm63xx_enet: properly prepare/unprepare clocks
- before/after usage
-
-Use clk_prepare_enable/disable_unprepare calls in preparation for
-switching to the generic clock framework.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/net/ethernet/broadcom/bcm63xx_enet.c | 12 ++++++------
- 1 file changed, 6 insertions(+), 6 deletions(-)
-
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-@@ -1671,7 +1671,7 @@ static int bcm_enet_probe(struct platfor
- ret = PTR_ERR(priv->mac_clk);
- goto out;
- }
-- clk_enable(priv->mac_clk);
-+ clk_prepare_enable(priv->mac_clk);
-
- /* initialize default and fetch platform data */
- priv->rx_ring_size = BCMENET_DEF_RX_DESC;
-@@ -1700,7 +1700,7 @@ static int bcm_enet_probe(struct platfor
- priv->phy_clk = NULL;
- goto out_put_clk_mac;
- }
-- clk_enable(priv->phy_clk);
-+ clk_prepare_enable(priv->phy_clk);
- }
-
- /* do minimal hardware init to be able to probe mii bus */
-@@ -1801,12 +1801,12 @@ out_uninit_hw:
- /* turn off mdc clock */
- enet_writel(priv, 0, ENET_MIISC_REG);
- if (priv->phy_clk) {
-- clk_disable(priv->phy_clk);
-+ clk_disable_unprepare(priv->phy_clk);
- clk_put(priv->phy_clk);
- }
-
- out_put_clk_mac:
-- clk_disable(priv->mac_clk);
-+ clk_disable_unprepare(priv->mac_clk);
- clk_put(priv->mac_clk);
- out:
- free_netdev(dev);
-@@ -1844,10 +1844,10 @@ static int bcm_enet_remove(struct platfo
-
- /* disable hw block clocks */
- if (priv->phy_clk) {
-- clk_disable(priv->phy_clk);
-+ clk_disable_unprepare(priv->phy_clk);
- clk_put(priv->phy_clk);
- }
-- clk_disable(priv->mac_clk);
-+ clk_disable_unprepare(priv->mac_clk);
- clk_put(priv->mac_clk);
-
- platform_set_drvdata(pdev, NULL);
+++ /dev/null
-From e1a3ace7260fad338a76595b116a6bf5b5627aa2 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Thu, 7 Mar 2013 12:20:10 +0100
-Subject: [PATCH 1/7] MIPS: BCM63XX: remove duplicate spi register definitions
-
-BCM6338 and BCM6348, and BCM6358 and everything after that share the
-same register layout. To not have to redefine them for each new chip
-and keep the code size small, only use the definitions for the first
-chip with the certain layout.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/dev-spi.c | 24 +++---------
- .../include/asm/mach-bcm63xx/bcm63xx_dev_spi.h | 10 +----
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 40 +-------------------
- 3 files changed, 10 insertions(+), 64 deletions(-)
-
---- a/arch/mips/bcm63xx/dev-spi.c
-+++ b/arch/mips/bcm63xx/dev-spi.c
-@@ -22,10 +22,6 @@
- /*
- * register offsets
- */
--static const unsigned long bcm6338_regs_spi[] = {
-- __GEN_SPI_REGS_TABLE(6338)
--};
--
- static const unsigned long bcm6348_regs_spi[] = {
- __GEN_SPI_REGS_TABLE(6348)
- };
-@@ -34,23 +30,15 @@ static const unsigned long bcm6358_regs_
- __GEN_SPI_REGS_TABLE(6358)
- };
-
--static const unsigned long bcm6368_regs_spi[] = {
-- __GEN_SPI_REGS_TABLE(6368)
--};
--
- const unsigned long *bcm63xx_regs_spi;
- EXPORT_SYMBOL(bcm63xx_regs_spi);
-
- static __init void bcm63xx_spi_regs_init(void)
- {
-- if (BCMCPU_IS_6338())
-- bcm63xx_regs_spi = bcm6338_regs_spi;
-- if (BCMCPU_IS_6348())
-+ if (BCMCPU_IS_6338() || BCMCPU_IS_6348())
- bcm63xx_regs_spi = bcm6348_regs_spi;
-- if (BCMCPU_IS_6358())
-+ if (BCMCPU_IS_6358() || BCMCPU_IS_6368())
- bcm63xx_regs_spi = bcm6358_regs_spi;
-- if (BCMCPU_IS_6368())
-- bcm63xx_regs_spi = bcm6368_regs_spi;
- }
- #else
- static __init void bcm63xx_spi_regs_init(void) { }
-@@ -93,10 +81,10 @@ int __init bcm63xx_spi_register(void)
- spi_resources[1].start = bcm63xx_get_irq_number(IRQ_SPI);
-
- if (BCMCPU_IS_6338() || BCMCPU_IS_6348()) {
-- spi_resources[0].end += BCM_6338_RSET_SPI_SIZE - 1;
-- spi_pdata.fifo_size = SPI_6338_MSG_DATA_SIZE;
-- spi_pdata.msg_type_shift = SPI_6338_MSG_TYPE_SHIFT;
-- spi_pdata.msg_ctl_width = SPI_6338_MSG_CTL_WIDTH;
-+ spi_resources[0].end += BCM_6348_RSET_SPI_SIZE - 1;
-+ spi_pdata.fifo_size = SPI_6348_MSG_DATA_SIZE;
-+ spi_pdata.msg_type_shift = SPI_6348_MSG_TYPE_SHIFT;
-+ spi_pdata.msg_ctl_width = SPI_6348_MSG_CTL_WIDTH;
- }
-
- if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
-@@ -71,18 +71,12 @@ static inline unsigned long bcm63xx_spir
-
- return bcm63xx_regs_spi[reg];
- #else
--#ifdef CONFIG_BCM63XX_CPU_6338
-- __GEN_SPI_RSET(6338)
--#endif
--#ifdef CONFIG_BCM63XX_CPU_6348
-+#if defined(CONFIG_BCM63XX_CPU_6338) || defined(CONFIG_BCM63XX_CPU_6348)
- __GEN_SPI_RSET(6348)
- #endif
--#ifdef CONFIG_BCM63XX_CPU_6358
-+#if defined(CONFIG_BCM63XX_CPU_6358) || defined(CONFIG_BCM63XX_CPU_6368)
- __GEN_SPI_RSET(6358)
- #endif
--#ifdef CONFIG_BCM63XX_CPU_6368
-- __GEN_SPI_RSET(6368)
--#endif
- #endif
- return 0;
- }
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -1223,24 +1223,7 @@
- * _REG relative to RSET_SPI
- *************************************************************************/
-
--/* BCM 6338 SPI core */
--#define SPI_6338_CMD 0x00 /* 16-bits register */
--#define SPI_6338_INT_STATUS 0x02
--#define SPI_6338_INT_MASK_ST 0x03
--#define SPI_6338_INT_MASK 0x04
--#define SPI_6338_ST 0x05
--#define SPI_6338_CLK_CFG 0x06
--#define SPI_6338_FILL_BYTE 0x07
--#define SPI_6338_MSG_TAIL 0x09
--#define SPI_6338_RX_TAIL 0x0b
--#define SPI_6338_MSG_CTL 0x40 /* 8-bits register */
--#define SPI_6338_MSG_CTL_WIDTH 8
--#define SPI_6338_MSG_DATA 0x41
--#define SPI_6338_MSG_DATA_SIZE 0x3f
--#define SPI_6338_RX_DATA 0x80
--#define SPI_6338_RX_DATA_SIZE 0x3f
--
--/* BCM 6348 SPI core */
-+/* BCM 6338/6348 SPI core */
- #define SPI_6348_CMD 0x00 /* 16-bits register */
- #define SPI_6348_INT_STATUS 0x02
- #define SPI_6348_INT_MASK_ST 0x03
-@@ -1257,7 +1240,7 @@
- #define SPI_6348_RX_DATA 0x80
- #define SPI_6348_RX_DATA_SIZE 0x3f
-
--/* BCM 6358 SPI core */
-+/* BCM 6358/6368 SPI core */
- #define SPI_6358_MSG_CTL 0x00 /* 16-bits register */
- #define SPI_6358_MSG_CTL_WIDTH 16
- #define SPI_6358_MSG_DATA 0x02
-@@ -1274,23 +1257,6 @@
- #define SPI_6358_MSG_TAIL 0x709
- #define SPI_6358_RX_TAIL 0x70B
-
--/* BCM 6358 SPI core */
--#define SPI_6368_MSG_CTL 0x00 /* 16-bits register */
--#define SPI_6368_MSG_CTL_WIDTH 16
--#define SPI_6368_MSG_DATA 0x02
--#define SPI_6368_MSG_DATA_SIZE 0x21e
--#define SPI_6368_RX_DATA 0x400
--#define SPI_6368_RX_DATA_SIZE 0x220
--#define SPI_6368_CMD 0x700 /* 16-bits register */
--#define SPI_6368_INT_STATUS 0x702
--#define SPI_6368_INT_MASK_ST 0x703
--#define SPI_6368_INT_MASK 0x704
--#define SPI_6368_ST 0x705
--#define SPI_6368_CLK_CFG 0x706
--#define SPI_6368_FILL_BYTE 0x707
--#define SPI_6368_MSG_TAIL 0x709
--#define SPI_6368_RX_TAIL 0x70B
--
- /* Shared SPI definitions */
-
- /* Message configuration */
-@@ -1298,10 +1264,8 @@
- #define SPI_HD_W 0x01
- #define SPI_HD_R 0x02
- #define SPI_BYTE_CNT_SHIFT 0
--#define SPI_6338_MSG_TYPE_SHIFT 6
- #define SPI_6348_MSG_TYPE_SHIFT 6
- #define SPI_6358_MSG_TYPE_SHIFT 14
--#define SPI_6368_MSG_TYPE_SHIFT 14
-
- /* Command */
- #define SPI_CMD_NOOP 0x00
+++ /dev/null
-From 609c69339a24bd034f5359dad14087276ce5a83f Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sun, 15 Jan 2012 14:41:22 +0100
-Subject: [PATCH 2/7] MIPS: BCM63XX: fix revision ID width
-
-The REVID is only 8 bit wide.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/cpu.c | 4 ++--
- arch/mips/bcm63xx/setup.c | 2 +-
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 2 +-
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 2 +-
- 4 files changed, 5 insertions(+), 5 deletions(-)
-
---- a/arch/mips/bcm63xx/cpu.c
-+++ b/arch/mips/bcm63xx/cpu.c
-@@ -25,7 +25,7 @@ const int *bcm63xx_irqs;
- EXPORT_SYMBOL(bcm63xx_irqs);
-
- static u16 bcm63xx_cpu_id;
--static u16 bcm63xx_cpu_rev;
-+static u8 bcm63xx_cpu_rev;
- static unsigned int bcm63xx_cpu_freq;
- static unsigned int bcm63xx_memory_size;
-
-@@ -87,7 +87,7 @@ u16 __bcm63xx_get_cpu_id(void)
-
- EXPORT_SYMBOL(__bcm63xx_get_cpu_id);
-
--u16 bcm63xx_get_cpu_rev(void)
-+u8 bcm63xx_get_cpu_rev(void)
- {
- return bcm63xx_cpu_rev;
- }
---- a/arch/mips/bcm63xx/setup.c
-+++ b/arch/mips/bcm63xx/setup.c
-@@ -126,7 +126,7 @@ static void __bcm63xx_machine_reboot(cha
- const char *get_system_type(void)
- {
- static char buf[128];
-- snprintf(buf, sizeof(buf), "bcm63xx/%s (0x%04x/0x%04X)",
-+ snprintf(buf, sizeof(buf), "bcm63xx/%s (0x%04x/0x%02X)",
- board_get_name(),
- bcm63xx_get_cpu_id(), bcm63xx_get_cpu_rev());
- return buf;
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-@@ -18,7 +18,7 @@
-
- void __init bcm63xx_cpu_init(void);
- u16 __bcm63xx_get_cpu_id(void);
--u16 bcm63xx_get_cpu_rev(void);
-+u8 bcm63xx_get_cpu_rev(void);
- unsigned int bcm63xx_get_cpu_freq(void);
-
- #ifdef CONFIG_BCM63XX_CPU_6328
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -10,7 +10,7 @@
- #define REV_CHIPID_SHIFT 16
- #define REV_CHIPID_MASK (0xffff << REV_CHIPID_SHIFT)
- #define REV_REVID_SHIFT 0
--#define REV_REVID_MASK (0xffff << REV_REVID_SHIFT)
-+#define REV_REVID_MASK (0xff << REV_REVID_SHIFT)
-
- /* Clock Control register */
- #define PERF_CKCTL_REG 0x4
+++ /dev/null
-From 3f4570c9794fcae1cf62fbf3266a2e23edac67a5 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Wed, 27 Jun 2012 15:01:09 +0200
-Subject: [PATCH 3/7] MIPS: BCM63XX: rework chip detection
-
-Instead of trying to use a correlation of cpu prid and chip id and
-hoping they will always be unique, use the cpu prid to determine the
-chip id register location and just read out the chip id.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/cpu.c | 87 +++++++++++++++++++++++------------------------
- 1 file changed, 42 insertions(+), 45 deletions(-)
-
---- a/arch/mips/bcm63xx/cpu.c
-+++ b/arch/mips/bcm63xx/cpu.c
-@@ -240,53 +240,27 @@ static unsigned int detect_memory_size(v
-
- void __init bcm63xx_cpu_init(void)
- {
-- unsigned int tmp, expected_cpu_id;
-+ unsigned int tmp;
- struct cpuinfo_mips *c = ¤t_cpu_data;
- unsigned int cpu = smp_processor_id();
-+ u32 chipid_reg;
-
- /* soc registers location depends on cpu type */
-- expected_cpu_id = 0;
-+ chipid_reg = 0;
-
- switch (c->cputype) {
- case CPU_BMIPS3300:
-- if ((read_c0_prid() & 0xff00) == PRID_IMP_BMIPS3300_ALT) {
-- expected_cpu_id = BCM6348_CPU_ID;
-- bcm63xx_regs_base = bcm6348_regs_base;
-- bcm63xx_irqs = bcm6348_irqs;
-- } else {
-+ if ((read_c0_prid() & 0xff00) != PRID_IMP_BMIPS3300_ALT)
- __cpu_name[cpu] = "Broadcom BCM6338";
-- expected_cpu_id = BCM6338_CPU_ID;
-- bcm63xx_regs_base = bcm6338_regs_base;
-- bcm63xx_irqs = bcm6338_irqs;
-- }
-- break;
-+ /* fall-through */
- case CPU_BMIPS32:
-- expected_cpu_id = BCM6345_CPU_ID;
-- bcm63xx_regs_base = bcm6345_regs_base;
-- bcm63xx_irqs = bcm6345_irqs;
-+ chipid_reg = BCM_6345_PERF_BASE;
- break;
- case CPU_BMIPS4350:
-- if ((read_c0_prid() & 0xf0) == 0x10) {
-- expected_cpu_id = BCM6358_CPU_ID;
-- bcm63xx_regs_base = bcm6358_regs_base;
-- bcm63xx_irqs = bcm6358_irqs;
-- } else {
-- /* all newer chips have the same chip id location */
-- u16 chip_id = bcm_readw(BCM_6368_PERF_BASE);
--
-- switch (chip_id) {
-- case BCM6328_CPU_ID:
-- expected_cpu_id = BCM6328_CPU_ID;
-- bcm63xx_regs_base = bcm6328_regs_base;
-- bcm63xx_irqs = bcm6328_irqs;
-- break;
-- case BCM6368_CPU_ID:
-- expected_cpu_id = BCM6368_CPU_ID;
-- bcm63xx_regs_base = bcm6368_regs_base;
-- bcm63xx_irqs = bcm6368_irqs;
-- break;
-- }
-- }
-+ if ((read_c0_prid() & 0xf0) == 0x10)
-+ chipid_reg = BCM_6345_PERF_BASE;
-+ else
-+ chipid_reg = BCM_6368_PERF_BASE;
- break;
- }
-
-@@ -294,20 +268,43 @@ void __init bcm63xx_cpu_init(void)
- * really early to panic, but delaying panic would not help since we
- * will never get any working console
- */
-- if (!expected_cpu_id)
-+ if (!chipid_reg)
- panic("unsupported Broadcom CPU");
-
-- /*
-- * bcm63xx_regs_base is set, we can access soc registers
-- */
--
-- /* double check CPU type */
-- tmp = bcm_perf_readl(PERF_REV_REG);
-+ /* read out CPU type */
-+ tmp = bcm_readl(chipid_reg);
- bcm63xx_cpu_id = (tmp & REV_CHIPID_MASK) >> REV_CHIPID_SHIFT;
- bcm63xx_cpu_rev = (tmp & REV_REVID_MASK) >> REV_REVID_SHIFT;
-
-- if (bcm63xx_cpu_id != expected_cpu_id)
-- panic("bcm63xx CPU id mismatch");
-+ switch (bcm63xx_cpu_id) {
-+ case BCM6328_CPU_ID:
-+ bcm63xx_regs_base = bcm6328_regs_base;
-+ bcm63xx_irqs = bcm6328_irqs;
-+ break;
-+ case BCM6338_CPU_ID:
-+ bcm63xx_regs_base = bcm6338_regs_base;
-+ bcm63xx_irqs = bcm6338_irqs;
-+ break;
-+ case BCM6345_CPU_ID:
-+ bcm63xx_regs_base = bcm6345_regs_base;
-+ bcm63xx_irqs = bcm6345_irqs;
-+ break;
-+ case BCM6348_CPU_ID:
-+ bcm63xx_regs_base = bcm6348_regs_base;
-+ bcm63xx_irqs = bcm6348_irqs;
-+ break;
-+ case BCM6358_CPU_ID:
-+ bcm63xx_regs_base = bcm6358_regs_base;
-+ bcm63xx_irqs = bcm6358_irqs;
-+ break;
-+ case BCM6368_CPU_ID:
-+ bcm63xx_regs_base = bcm6368_regs_base;
-+ bcm63xx_irqs = bcm6368_irqs;
-+ break;
-+ default:
-+ panic("unsupported broadcom CPU %x", bcm63xx_cpu_id);
-+ break;
-+ }
-
- bcm63xx_cpu_freq = detect_cpu_clock();
- bcm63xx_memory_size = detect_memory_size();
+++ /dev/null
-From 1071a9c9527d68eca4605e2eb1686609bfecf287 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 21 Nov 2011 00:48:52 +0100
-Subject: [PATCH 4/7] MIPS: BCM63XX: add basic BCM6362 support
-
-Add basic support for detecting and booting the BCM6362.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/Kconfig | 4 +
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 6 +-
- arch/mips/bcm63xx/cpu.c | 51 +++++++-
- arch/mips/bcm63xx/irq.c | 22 ++++
- arch/mips/bcm63xx/prom.c | 2 +
- arch/mips/bcm63xx/reset.c | 28 +++++
- arch/mips/bcm63xx/setup.c | 3 +
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 139 +++++++++++++++++++++
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h | 2 +
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 61 ++++++++-
- arch/mips/include/asm/mach-bcm63xx/ioremap.h | 1 +
- 11 files changed, 314 insertions(+), 5 deletions(-)
-
---- a/arch/mips/bcm63xx/Kconfig
-+++ b/arch/mips/bcm63xx/Kconfig
-@@ -25,6 +25,10 @@ config BCM63XX_CPU_6358
- bool "support 6358 CPU"
- select HW_HAS_PCI
-
-+config BCM63XX_CPU_6362
-+ bool "support 6362 CPU"
-+ select HW_HAS_PCI
-+
- config BCM63XX_CPU_6368
- bool "support 6368 CPU"
- select HW_HAS_PCI
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -726,11 +726,11 @@ void __init board_prom_init(void)
- u32 val;
-
- /* read base address of boot chip select (0)
-- * 6328 does not have MPI but boots from a fixed address
-+ * 6328/6362 do not have MPI but boot from a fixed address
- */
-- if (BCMCPU_IS_6328())
-+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) {
- val = 0x18000000;
-- else {
-+ } else {
- val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- val &= MPI_CSBASE_BASE_MASK;
- }
---- a/arch/mips/bcm63xx/cpu.c
-+++ b/arch/mips/bcm63xx/cpu.c
-@@ -71,6 +71,15 @@ static const int bcm6358_irqs[] = {
-
- };
-
-+static const unsigned long bcm6362_regs_base[] = {
-+ __GEN_CPU_REGS_TABLE(6362)
-+};
-+
-+static const int bcm6362_irqs[] = {
-+ __GEN_CPU_IRQ_TABLE(6362)
-+
-+};
-+
- static const unsigned long bcm6368_regs_base[] = {
- __GEN_CPU_REGS_TABLE(6368)
- };
-@@ -169,6 +178,42 @@ static unsigned int detect_cpu_clock(voi
- return (16 * 1000000 * n1 * n2) / m1;
- }
-
-+ case BCM6362_CPU_ID:
-+ {
-+ unsigned int tmp, mips_pll_fcvo;
-+
-+ tmp = bcm_misc_readl(MISC_STRAPBUS_6362_REG);
-+ mips_pll_fcvo = (tmp & STRAPBUS_6362_FCVO_MASK)
-+ >> STRAPBUS_6362_FCVO_SHIFT;
-+ switch (mips_pll_fcvo) {
-+ case 0x03:
-+ case 0x0b:
-+ case 0x13:
-+ case 0x1b:
-+ return 240000000;
-+ case 0x04:
-+ case 0x0c:
-+ case 0x14:
-+ case 0x1c:
-+ return 160000000;
-+ case 0x05:
-+ case 0x0e:
-+ case 0x16:
-+ case 0x1e:
-+ case 0x1f:
-+ return 400000000;
-+ case 0x06:
-+ return 440000000;
-+ case 0x07:
-+ case 0x17:
-+ return 384000000;
-+ case 0x15:
-+ case 0x1d:
-+ return 200000000;
-+ default:
-+ return 320000000;
-+ }
-+ }
- case BCM6368_CPU_ID:
- {
- unsigned int tmp, p1, p2, ndiv, m1;
-@@ -205,7 +250,7 @@ static unsigned int detect_memory_size(v
- unsigned int cols = 0, rows = 0, is_32bits = 0, banks = 0;
- u32 val;
-
-- if (BCMCPU_IS_6328())
-+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362())
- return bcm_ddr_readl(DDR_CSEND_REG) << 24;
-
- if (BCMCPU_IS_6345()) {
-@@ -297,6 +342,10 @@ void __init bcm63xx_cpu_init(void)
- bcm63xx_regs_base = bcm6358_regs_base;
- bcm63xx_irqs = bcm6358_irqs;
- break;
-+ case BCM6362_CPU_ID:
-+ bcm63xx_regs_base = bcm6362_regs_base;
-+ bcm63xx_irqs = bcm6362_irqs;
-+ break;
- case BCM6368_CPU_ID:
- bcm63xx_regs_base = bcm6368_regs_base;
- bcm63xx_irqs = bcm6368_irqs;
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -82,6 +82,17 @@ static void __internal_irq_unmask_64(uns
- #define ext_irq_cfg_reg1 PERF_EXTIRQ_CFG_REG_6358
- #define ext_irq_cfg_reg2 0
- #endif
-+#ifdef CONFIG_BCM63XX_CPU_6362
-+#define irq_stat_reg PERF_IRQSTAT_6362_REG
-+#define irq_mask_reg PERF_IRQMASK_6362_REG
-+#define irq_bits 64
-+#define is_ext_irq_cascaded 1
-+#define ext_irq_start (BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE)
-+#define ext_irq_end (BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE)
-+#define ext_irq_count 4
-+#define ext_irq_cfg_reg1 PERF_EXTIRQ_CFG_REG_6362
-+#define ext_irq_cfg_reg2 0
-+#endif
- #ifdef CONFIG_BCM63XX_CPU_6368
- #define irq_stat_reg PERF_IRQSTAT_6368_REG
- #define irq_mask_reg PERF_IRQMASK_6368_REG
-@@ -170,6 +181,16 @@ static void bcm63xx_init_irq(void)
- ext_irq_end = BCM_6358_EXT_IRQ3 - IRQ_INTERNAL_BASE;
- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6358;
- break;
-+ case BCM6362_CPU_ID:
-+ irq_stat_addr += PERF_IRQSTAT_6362_REG;
-+ irq_mask_addr += PERF_IRQMASK_6362_REG;
-+ irq_bits = 64;
-+ ext_irq_count = 4;
-+ is_ext_irq_cascaded = 1;
-+ ext_irq_start = BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE;
-+ ext_irq_end = BCM_6362_EXT_IRQ3 - IRQ_INTERNAL_BASE;
-+ ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6362;
-+ break;
- case BCM6368_CPU_ID:
- irq_stat_addr += PERF_IRQSTAT_6368_REG;
- irq_mask_addr += PERF_IRQMASK_6368_REG;
-@@ -458,6 +479,7 @@ static int bcm63xx_external_irq_set_type
- case BCM6338_CPU_ID:
- case BCM6345_CPU_ID:
- case BCM6358_CPU_ID:
-+ case BCM6362_CPU_ID:
- case BCM6368_CPU_ID:
- if (levelsense)
- reg |= EXTIRQ_CFG_LEVELSENSE(irq);
---- a/arch/mips/bcm63xx/prom.c
-+++ b/arch/mips/bcm63xx/prom.c
-@@ -36,6 +36,8 @@ void __init prom_init(void)
- mask = CKCTL_6348_ALL_SAFE_EN;
- else if (BCMCPU_IS_6358())
- mask = CKCTL_6358_ALL_SAFE_EN;
-+ else if (BCMCPU_IS_6362())
-+ mask = CKCTL_6362_ALL_SAFE_EN;
- else if (BCMCPU_IS_6368())
- mask = CKCTL_6368_ALL_SAFE_EN;
- else
---- a/arch/mips/bcm63xx/reset.c
-+++ b/arch/mips/bcm63xx/reset.c
-@@ -85,6 +85,20 @@
- #define BCM6358_RESET_PCIE 0
- #define BCM6358_RESET_PCIE_EXT 0
-
-+#define BCM6362_RESET_SPI SOFTRESET_6362_SPI_MASK
-+#define BCM6362_RESET_ENET 0
-+#define BCM6362_RESET_USBH SOFTRESET_6362_USBH_MASK
-+#define BCM6362_RESET_USBD SOFTRESET_6362_USBS_MASK
-+#define BCM6362_RESET_DSL 0
-+#define BCM6362_RESET_SAR SOFTRESET_6362_SAR_MASK
-+#define BCM6362_RESET_EPHY SOFTRESET_6362_EPHY_MASK
-+#define BCM6362_RESET_ENETSW SOFTRESET_6362_ENETSW_MASK
-+#define BCM6362_RESET_PCM SOFTRESET_6362_PCM_MASK
-+#define BCM6362_RESET_MPI 0
-+#define BCM6362_RESET_PCIE (SOFTRESET_6362_PCIE_MASK | \
-+ SOFTRESET_6362_PCIE_CORE_MASK)
-+#define BCM6362_RESET_PCIE_EXT SOFTRESET_6362_PCIE_EXT_MASK
-+
- #define BCM6368_RESET_SPI SOFTRESET_6368_SPI_MASK
- #define BCM6368_RESET_ENET 0
- #define BCM6368_RESET_USBH SOFTRESET_6368_USBH_MASK
-@@ -119,6 +133,10 @@ static const u32 bcm6358_reset_bits[] =
- __GEN_RESET_BITS_TABLE(6358)
- };
-
-+static const u32 bcm6362_reset_bits[] = {
-+ __GEN_RESET_BITS_TABLE(6362)
-+};
-+
- static const u32 bcm6368_reset_bits[] = {
- __GEN_RESET_BITS_TABLE(6368)
- };
-@@ -140,6 +158,9 @@ static int __init bcm63xx_reset_bits_ini
- } else if (BCMCPU_IS_6358()) {
- reset_reg = PERF_SOFTRESET_6358_REG;
- bcm63xx_reset_bits = bcm6358_reset_bits;
-+ } else if (BCMCPU_IS_6362()) {
-+ reset_reg = PERF_SOFTRESET_6362_REG;
-+ bcm63xx_reset_bits = bcm6362_reset_bits;
- } else if (BCMCPU_IS_6368()) {
- reset_reg = PERF_SOFTRESET_6368_REG;
- bcm63xx_reset_bits = bcm6368_reset_bits;
-@@ -182,6 +203,13 @@ static const u32 bcm63xx_reset_bits[] =
- #define reset_reg PERF_SOFTRESET_6358_REG
- #endif
-
-+#ifdef CONFIG_BCM63XX_CPU_6362
-+static const u32 bcm63xx_reset_bits[] = {
-+ __GEN_RESET_BITS_TABLE(6362)
-+};
-+#define reset_reg PERF_SOFTRESET_6362_REG
-+#endif
-+
- #ifdef CONFIG_BCM63XX_CPU_6368
- static const u32 bcm63xx_reset_bits[] = {
- __GEN_RESET_BITS_TABLE(6368)
---- a/arch/mips/bcm63xx/setup.c
-+++ b/arch/mips/bcm63xx/setup.c
-@@ -83,6 +83,9 @@ void bcm63xx_machine_reboot(void)
- case BCM6358_CPU_ID:
- perf_regs[0] = PERF_EXTIRQ_CFG_REG_6358;
- break;
-+ case BCM6362_CPU_ID:
-+ perf_regs[0] = PERF_EXTIRQ_CFG_REG_6362;
-+ break;
- }
-
- for (i = 0; i < 2; i++) {
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-@@ -14,6 +14,7 @@
- #define BCM6345_CPU_ID 0x6345
- #define BCM6348_CPU_ID 0x6348
- #define BCM6358_CPU_ID 0x6358
-+#define BCM6362_CPU_ID 0x6362
- #define BCM6368_CPU_ID 0x6368
-
- void __init bcm63xx_cpu_init(void);
-@@ -86,6 +87,20 @@ unsigned int bcm63xx_get_cpu_freq(void);
- # define BCMCPU_IS_6358() (0)
- #endif
-
-+#ifdef CONFIG_BCM63XX_CPU_6362
-+# ifdef bcm63xx_get_cpu_id
-+# undef bcm63xx_get_cpu_id
-+# define bcm63xx_get_cpu_id() __bcm63xx_get_cpu_id()
-+# define BCMCPU_RUNTIME_DETECT
-+# else
-+# define bcm63xx_get_cpu_id() BCM6362_CPU_ID
-+# endif
-+# define BCMCPU_IS_6362() (bcm63xx_get_cpu_id() == BCM6362_CPU_ID)
-+#else
-+# define BCMCPU_IS_6362() (0)
-+#endif
-+
-+
- #ifdef CONFIG_BCM63XX_CPU_6368
- # ifdef bcm63xx_get_cpu_id
- # undef bcm63xx_get_cpu_id
-@@ -406,6 +421,62 @@ enum bcm63xx_regs_set {
-
-
- /*
-+ * 6362 register sets base address
-+ */
-+#define BCM_6362_DSL_LMEM_BASE (0xdeadbeef)
-+#define BCM_6362_PERF_BASE (0xb0000000)
-+#define BCM_6362_TIMER_BASE (0xb0000040)
-+#define BCM_6362_WDT_BASE (0xb000005c)
-+#define BCM_6362_UART0_BASE (0xb0000100)
-+#define BCM_6362_UART1_BASE (0xb0000120)
-+#define BCM_6362_GPIO_BASE (0xb0000080)
-+#define BCM_6362_SPI_BASE (0xb0000800)
-+#define BCM_6362_HSSPI_BASE (0xb0001000)
-+#define BCM_6362_UDC0_BASE (0xdeadbeef)
-+#define BCM_6362_USBDMA_BASE (0xb000c000)
-+#define BCM_6362_OHCI0_BASE (0xb0002600)
-+#define BCM_6362_OHCI_PRIV_BASE (0xdeadbeef)
-+#define BCM_6362_USBH_PRIV_BASE (0xb0002700)
-+#define BCM_6362_USBD_BASE (0xb0002400)
-+#define BCM_6362_MPI_BASE (0xdeadbeef)
-+#define BCM_6362_PCMCIA_BASE (0xdeadbeef)
-+#define BCM_6362_PCIE_BASE (0xb0e40000)
-+#define BCM_6362_SDRAM_REGS_BASE (0xdeadbeef)
-+#define BCM_6362_DSL_BASE (0xdeadbeef)
-+#define BCM_6362_UBUS_BASE (0xdeadbeef)
-+#define BCM_6362_ENET0_BASE (0xdeadbeef)
-+#define BCM_6362_ENET1_BASE (0xdeadbeef)
-+#define BCM_6362_ENETDMA_BASE (0xb000d800)
-+#define BCM_6362_ENETDMAC_BASE (0xb000da00)
-+#define BCM_6362_ENETDMAS_BASE (0xb000dc00)
-+#define BCM_6362_ENETSW_BASE (0xb0e00000)
-+#define BCM_6362_EHCI0_BASE (0xb0002500)
-+#define BCM_6362_SDRAM_BASE (0xdeadbeef)
-+#define BCM_6362_MEMC_BASE (0xdeadbeef)
-+#define BCM_6362_DDR_BASE (0xb0003000)
-+#define BCM_6362_M2M_BASE (0xdeadbeef)
-+#define BCM_6362_ATM_BASE (0xdeadbeef)
-+#define BCM_6362_XTM_BASE (0xb0007800)
-+#define BCM_6362_XTMDMA_BASE (0xb000b800)
-+#define BCM_6362_XTMDMAC_BASE (0xdeadbeef)
-+#define BCM_6362_XTMDMAS_BASE (0xdeadbeef)
-+#define BCM_6362_PCM_BASE (0xb000a800)
-+#define BCM_6362_PCMDMA_BASE (0xdeadbeef)
-+#define BCM_6362_PCMDMAC_BASE (0xdeadbeef)
-+#define BCM_6362_PCMDMAS_BASE (0xdeadbeef)
-+#define BCM_6362_RNG_BASE (0xdeadbeef)
-+#define BCM_6362_MISC_BASE (0xb0001800)
-+
-+#define BCM_6362_NAND_REG_BASE (0xb0000200)
-+#define BCM_6362_NAND_CACHE_BASE (0xb0000600)
-+#define BCM_6362_LED_BASE (0xb0001900)
-+#define BCM_6362_IPSEC_BASE (0xb0002800)
-+#define BCM_6362_IPSEC_DMA_BASE (0xb000d000)
-+#define BCM_6362_WLAN_CHIPCOMMON_BASE (0xb0004000)
-+#define BCM_6362_WLAN_D11_BASE (0xb0005000)
-+#define BCM_6362_WLAN_SHIM_BASE (0xb0007000)
-+
-+/*
- * 6368 register sets base address
- */
- #define BCM_6368_DSL_LMEM_BASE (0xdeadbeef)
-@@ -564,6 +635,9 @@ static inline unsigned long bcm63xx_regs
- #ifdef CONFIG_BCM63XX_CPU_6358
- __GEN_RSET(6358)
- #endif
-+#ifdef CONFIG_BCM63XX_CPU_6362
-+ __GEN_RSET(6362)
-+#endif
- #ifdef CONFIG_BCM63XX_CPU_6368
- __GEN_RSET(6368)
- #endif
-@@ -820,6 +894,71 @@ enum bcm63xx_irq {
- #define BCM_6358_EXT_IRQ3 (IRQ_INTERNAL_BASE + 28)
-
- /*
-+ * 6362 irqs
-+ */
-+#define BCM_6362_HIGH_IRQ_BASE (IRQ_INTERNAL_BASE + 32)
-+
-+#define BCM_6362_TIMER_IRQ (IRQ_INTERNAL_BASE + 0)
-+#define BCM_6362_SPI_IRQ (IRQ_INTERNAL_BASE + 2)
-+#define BCM_6362_UART0_IRQ (IRQ_INTERNAL_BASE + 3)
-+#define BCM_6362_UART1_IRQ (IRQ_INTERNAL_BASE + 4)
-+#define BCM_6362_DSL_IRQ (IRQ_INTERNAL_BASE + 28)
-+#define BCM_6362_UDC0_IRQ 0
-+#define BCM_6362_ENET0_IRQ 0
-+#define BCM_6362_ENET1_IRQ 0
-+#define BCM_6362_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 14)
-+#define BCM_6362_HSSPI_IRQ (IRQ_INTERNAL_BASE + 5)
-+#define BCM_6362_OHCI0_IRQ (IRQ_INTERNAL_BASE + 9)
-+#define BCM_6362_EHCI0_IRQ (IRQ_INTERNAL_BASE + 10)
-+#define BCM_6362_USBD_IRQ (IRQ_INTERNAL_BASE + 11)
-+#define BCM_6362_USBD_RXDMA0_IRQ (IRQ_INTERNAL_BASE + 20)
-+#define BCM_6362_USBD_TXDMA0_IRQ (IRQ_INTERNAL_BASE + 21)
-+#define BCM_6362_USBD_RXDMA1_IRQ (IRQ_INTERNAL_BASE + 22)
-+#define BCM_6362_USBD_TXDMA1_IRQ (IRQ_INTERNAL_BASE + 23)
-+#define BCM_6362_USBD_RXDMA2_IRQ (IRQ_INTERNAL_BASE + 24)
-+#define BCM_6362_USBD_TXDMA2_IRQ (IRQ_INTERNAL_BASE + 25)
-+#define BCM_6362_PCMCIA_IRQ 0
-+#define BCM_6362_ENET0_RXDMA_IRQ 0
-+#define BCM_6362_ENET0_TXDMA_IRQ 0
-+#define BCM_6362_ENET1_RXDMA_IRQ 0
-+#define BCM_6362_ENET1_TXDMA_IRQ 0
-+#define BCM_6362_PCI_IRQ (IRQ_INTERNAL_BASE + 30)
-+#define BCM_6362_ATM_IRQ 0
-+#define BCM_6362_ENETSW_RXDMA0_IRQ (BCM_6362_HIGH_IRQ_BASE + 0)
-+#define BCM_6362_ENETSW_RXDMA1_IRQ (BCM_6362_HIGH_IRQ_BASE + 1)
-+#define BCM_6362_ENETSW_RXDMA2_IRQ (BCM_6362_HIGH_IRQ_BASE + 2)
-+#define BCM_6362_ENETSW_RXDMA3_IRQ (BCM_6362_HIGH_IRQ_BASE + 3)
-+#define BCM_6362_ENETSW_TXDMA0_IRQ 0
-+#define BCM_6362_ENETSW_TXDMA1_IRQ 0
-+#define BCM_6362_ENETSW_TXDMA2_IRQ 0
-+#define BCM_6362_ENETSW_TXDMA3_IRQ 0
-+#define BCM_6362_XTM_IRQ 0
-+#define BCM_6362_XTM_DMA0_IRQ (BCM_6362_HIGH_IRQ_BASE + 12)
-+
-+#define BCM_6362_RING_OSC_IRQ (IRQ_INTERNAL_BASE + 1)
-+#define BCM_6362_WLAN_GPIO_IRQ (IRQ_INTERNAL_BASE + 6)
-+#define BCM_6362_WLAN_IRQ (IRQ_INTERNAL_BASE + 7)
-+#define BCM_6362_IPSEC_IRQ (IRQ_INTERNAL_BASE + 8)
-+#define BCM_6362_NAND_IRQ (IRQ_INTERNAL_BASE + 12)
-+#define BCM_6362_PCM_IRQ (IRQ_INTERNAL_BASE + 13)
-+#define BCM_6362_DG_IRQ (IRQ_INTERNAL_BASE + 15)
-+#define BCM_6362_EPHY_ENERGY0_IRQ (IRQ_INTERNAL_BASE + 16)
-+#define BCM_6362_EPHY_ENERGY1_IRQ (IRQ_INTERNAL_BASE + 17)
-+#define BCM_6362_EPHY_ENERGY2_IRQ (IRQ_INTERNAL_BASE + 18)
-+#define BCM_6362_EPHY_ENERGY3_IRQ (IRQ_INTERNAL_BASE + 19)
-+#define BCM_6362_IPSEC_DMA0_IRQ (IRQ_INTERNAL_BASE + 26)
-+#define BCM_6362_IPSEC_DMA1_IRQ (IRQ_INTERNAL_BASE + 27)
-+#define BCM_6362_FAP0_IRQ (IRQ_INTERNAL_BASE + 29)
-+#define BCM_6362_PCM_DMA0_IRQ (BCM_6362_HIGH_IRQ_BASE + 4)
-+#define BCM_6362_PCM_DMA1_IRQ (BCM_6362_HIGH_IRQ_BASE + 5)
-+#define BCM_6362_DECT0_IRQ (BCM_6362_HIGH_IRQ_BASE + 6)
-+#define BCM_6362_DECT1_IRQ (BCM_6362_HIGH_IRQ_BASE + 7)
-+#define BCM_6362_EXT_IRQ0 (BCM_6362_HIGH_IRQ_BASE + 8)
-+#define BCM_6362_EXT_IRQ1 (BCM_6362_HIGH_IRQ_BASE + 9)
-+#define BCM_6362_EXT_IRQ2 (BCM_6362_HIGH_IRQ_BASE + 10)
-+#define BCM_6362_EXT_IRQ3 (BCM_6362_HIGH_IRQ_BASE + 11)
-+
-+/*
- * 6368 irqs
- */
- #define BCM_6368_HIGH_IRQ_BASE (IRQ_INTERNAL_BASE + 32)
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
-@@ -17,6 +17,8 @@ static inline unsigned long bcm63xx_gpio
- return 8;
- case BCM6345_CPU_ID:
- return 16;
-+ case BCM6362_CPU_ID:
-+ return 48;
- case BCM6368_CPU_ID:
- return 38;
- case BCM6348_CPU_ID:
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -112,6 +112,39 @@
- CKCTL_6358_USBSU_EN | \
- CKCTL_6358_EPHY_EN)
-
-+#define CKCTL_6362_ADSL_QPROC_EN (1 << 1)
-+#define CKCTL_6362_ADSL_AFE_EN (1 << 2)
-+#define CKCTL_6362_ADSL_EN (1 << 3)
-+#define CKCTL_6362_MIPS_EN (1 << 4)
-+#define CKCTL_6362_WLAN_OCP_EN (1 << 5)
-+#define CKCTL_6362_SWPKT_USB_EN (1 << 7)
-+#define CKCTL_6362_SWPKT_SAR_EN (1 << 8)
-+#define CKCTL_6362_SAR_EN (1 << 9)
-+#define CKCTL_6362_ROBOSW_EN (1 << 10)
-+#define CKCTL_6362_PCM_EN (1 << 11)
-+#define CKCTL_6362_USBD_EN (1 << 12)
-+#define CKCTL_6362_USBH_EN (1 << 13)
-+#define CKCTL_6362_IPSEC_EN (1 << 14)
-+#define CKCTL_6362_SPI_EN (1 << 15)
-+#define CKCTL_6362_HSSPI_EN (1 << 16)
-+#define CKCTL_6362_PCIE_EN (1 << 17)
-+#define CKCTL_6362_FAP_EN (1 << 18)
-+#define CKCTL_6362_PHYMIPS_EN (1 << 19)
-+#define CKCTL_6362_NAND_EN (1 << 20)
-+
-+#define CKCTL_6362_ALL_SAFE_EN (CKCTL_6362_PHYMIPS_EN | \
-+ CKCTL_6362_ADSL_QPROC_EN | \
-+ CKCTL_6362_ADSL_AFE_EN | \
-+ CKCTL_6362_ADSL_EN | \
-+ CKCTL_6362_SAR_EN | \
-+ CKCTL_6362_PCM_EN | \
-+ CKCTL_6362_IPSEC_EN | \
-+ CKCTL_6362_USBD_EN | \
-+ CKCTL_6362_USBH_EN | \
-+ CKCTL_6362_ROBOSW_EN | \
-+ CKCTL_6362_PCIE_EN)
-+
-+
- #define CKCTL_6368_VDSL_QPROC_EN (1 << 2)
- #define CKCTL_6368_VDSL_AFE_EN (1 << 3)
- #define CKCTL_6368_VDSL_BONDING_EN (1 << 4)
-@@ -153,6 +186,7 @@
- #define PERF_IRQMASK_6345_REG 0xc
- #define PERF_IRQMASK_6348_REG 0xc
- #define PERF_IRQMASK_6358_REG 0xc
-+#define PERF_IRQMASK_6362_REG 0x20
- #define PERF_IRQMASK_6368_REG 0x20
-
- /* Interrupt Status register */
-@@ -161,6 +195,7 @@
- #define PERF_IRQSTAT_6345_REG 0x10
- #define PERF_IRQSTAT_6348_REG 0x10
- #define PERF_IRQSTAT_6358_REG 0x10
-+#define PERF_IRQSTAT_6362_REG 0x28
- #define PERF_IRQSTAT_6368_REG 0x28
-
- /* External Interrupt Configuration register */
-@@ -169,6 +204,7 @@
- #define PERF_EXTIRQ_CFG_REG_6345 0x14
- #define PERF_EXTIRQ_CFG_REG_6348 0x14
- #define PERF_EXTIRQ_CFG_REG_6358 0x14
-+#define PERF_EXTIRQ_CFG_REG_6362 0x18
- #define PERF_EXTIRQ_CFG_REG_6368 0x18
-
- #define PERF_EXTIRQ_CFG_REG2_6368 0x1c
-@@ -197,6 +233,7 @@
- #define PERF_SOFTRESET_REG 0x28
- #define PERF_SOFTRESET_6328_REG 0x10
- #define PERF_SOFTRESET_6358_REG 0x34
-+#define PERF_SOFTRESET_6362_REG 0x10
- #define PERF_SOFTRESET_6368_REG 0x10
-
- #define SOFTRESET_6328_SPI_MASK (1 << 0)
-@@ -259,6 +296,22 @@
- #define SOFTRESET_6358_PCM_MASK (1 << 13)
- #define SOFTRESET_6358_ADSL_MASK (1 << 14)
-
-+#define SOFTRESET_6362_SPI_MASK (1 << 0)
-+#define SOFTRESET_6362_IPSEC_MASK (1 << 1)
-+#define SOFTRESET_6362_EPHY_MASK (1 << 2)
-+#define SOFTRESET_6362_SAR_MASK (1 << 3)
-+#define SOFTRESET_6362_ENETSW_MASK (1 << 4)
-+#define SOFTRESET_6362_USBS_MASK (1 << 5)
-+#define SOFTRESET_6362_USBH_MASK (1 << 6)
-+#define SOFTRESET_6362_PCM_MASK (1 << 7)
-+#define SOFTRESET_6362_PCIE_CORE_MASK (1 << 8)
-+#define SOFTRESET_6362_PCIE_MASK (1 << 9)
-+#define SOFTRESET_6362_PCIE_EXT_MASK (1 << 10)
-+#define SOFTRESET_6362_WLAN_SHIM_MASK (1 << 11)
-+#define SOFTRESET_6362_DDR_PHY_MASK (1 << 12)
-+#define SOFTRESET_6362_FAP_MASK (1 << 13)
-+#define SOFTRESET_6362_WLAN_UBUS_MASK (1 << 14)
-+
- #define SOFTRESET_6368_SPI_MASK (1 << 0)
- #define SOFTRESET_6368_MPI_MASK (1 << 3)
- #define SOFTRESET_6368_EPHY_MASK (1 << 6)
-@@ -1240,7 +1293,7 @@
- #define SPI_6348_RX_DATA 0x80
- #define SPI_6348_RX_DATA_SIZE 0x3f
-
--/* BCM 6358/6368 SPI core */
-+/* BCM 6358/6262/6368 SPI core */
- #define SPI_6358_MSG_CTL 0x00 /* 16-bits register */
- #define SPI_6358_MSG_CTL_WIDTH 16
- #define SPI_6358_MSG_DATA 0x02
-@@ -1316,6 +1369,12 @@
- #define SERDES_PCIE_EN (1 << 0)
- #define SERDES_PCIE_EXD_EN (1 << 15)
-
-+#define MISC_STRAPBUS_6362_REG 0x14
-+#define STRAPBUS_6362_FCVO_SHIFT 1
-+#define STRAPBUS_6362_FCVO_MASK (0x1f << STRAPBUS_6362_FCVO_SHIFT)
-+#define STRAPBUS_6362_BOOT_SEL_SERIAL (1 << 15)
-+#define STRAPBUS_6362_BOOT_SEL_NAND (0 << 15)
-+
- #define MISC_STRAPBUS_6328_REG 0x240
- #define STRAPBUS_6328_FCVO_SHIFT 7
- #define STRAPBUS_6328_FCVO_MASK (0x1f << STRAPBUS_6328_FCVO_SHIFT)
---- a/arch/mips/include/asm/mach-bcm63xx/ioremap.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/ioremap.h
-@@ -19,6 +19,7 @@ static inline int is_bcm63xx_internal_re
- return 1;
- break;
- case BCM6328_CPU_ID:
-+ case BCM6362_CPU_ID:
- case BCM6368_CPU_ID:
- if (offset >= 0xb0000000 && offset < 0xb1000000)
- return 1;
+++ /dev/null
-From 5da349ee614f61a2e6edb403098f40c6d40f2553 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Thu, 5 Jul 2012 21:19:20 +0200
-Subject: [PATCH 5/7] MIPS: BCM63XX: enable SPI controller for BCM6362
-
-The SPI controller shares the same register layout as the 6358 one.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/clk.c | 2 ++
- arch/mips/bcm63xx/dev-spi.c | 4 ++--
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h | 3 ++-
- 3 files changed, 6 insertions(+), 3 deletions(-)
-
---- a/arch/mips/bcm63xx/clk.c
-+++ b/arch/mips/bcm63xx/clk.c
-@@ -202,6 +202,8 @@ static void spi_set(struct clk *clk, int
- mask = CKCTL_6348_SPI_EN;
- else if (BCMCPU_IS_6358())
- mask = CKCTL_6358_SPI_EN;
-+ else if (BCMCPU_IS_6362())
-+ mask = CKCTL_6362_SPI_EN;
- else
- /* BCMCPU_IS_6368 */
- mask = CKCTL_6368_SPI_EN;
---- a/arch/mips/bcm63xx/dev-spi.c
-+++ b/arch/mips/bcm63xx/dev-spi.c
-@@ -37,7 +37,7 @@ static __init void bcm63xx_spi_regs_init
- {
- if (BCMCPU_IS_6338() || BCMCPU_IS_6348())
- bcm63xx_regs_spi = bcm6348_regs_spi;
-- if (BCMCPU_IS_6358() || BCMCPU_IS_6368())
-+ if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368())
- bcm63xx_regs_spi = bcm6358_regs_spi;
- }
- #else
-@@ -87,7 +87,7 @@ int __init bcm63xx_spi_register(void)
- spi_pdata.msg_ctl_width = SPI_6348_MSG_CTL_WIDTH;
- }
-
-- if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
-+ if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) {
- spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1;
- spi_pdata.fifo_size = SPI_6358_MSG_DATA_SIZE;
- spi_pdata.msg_type_shift = SPI_6358_MSG_TYPE_SHIFT;
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_spi.h
-@@ -74,7 +74,8 @@ static inline unsigned long bcm63xx_spir
- #if defined(CONFIG_BCM63XX_CPU_6338) || defined(CONFIG_BCM63XX_CPU_6348)
- __GEN_SPI_RSET(6348)
- #endif
--#if defined(CONFIG_BCM63XX_CPU_6358) || defined(CONFIG_BCM63XX_CPU_6368)
-+#if defined(CONFIG_BCM63XX_CPU_6358) || defined(CONFIG_BCM63XX_CPU_6362) || \
-+ defined(CONFIG_BCM63XX_CPU_6368)
- __GEN_SPI_RSET(6358)
- #endif
- #endif
+++ /dev/null
-From ec6f1e53b22d01e628b79b99f7a33960034e97e7 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 21 Nov 2011 00:53:26 +0100
-Subject: [PATCH 6/7] MIPS: BCM63XX: enable pcie for BCM6362
-
-The PCIe controller is almost the same as the BCM6328 one, with only
-the SERDES register being at a different location.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 3 ++-
- arch/mips/pci/pci-bcm63xx.c | 11 +++++++++--
- 2 files changed, 11 insertions(+), 3 deletions(-)
-
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -1365,7 +1365,8 @@
- /*************************************************************************
- * _REG relative to RSET_MISC
- *************************************************************************/
--#define MISC_SERDES_CTRL_REG 0x0
-+#define MISC_SERDES_CTRL_6328_REG 0x0
-+#define MISC_SERDES_CTRL_6362_REG 0x4
- #define SERDES_PCIE_EN (1 << 0)
- #define SERDES_PCIE_EXD_EN (1 << 15)
-
---- a/arch/mips/pci/pci-bcm63xx.c
-+++ b/arch/mips/pci/pci-bcm63xx.c
-@@ -121,11 +121,17 @@ void __iomem *pci_iospace_start;
- static void __init bcm63xx_reset_pcie(void)
- {
- u32 val;
-+ u32 reg;
-
- /* enable SERDES */
-- val = bcm_misc_readl(MISC_SERDES_CTRL_REG);
-+ if (BCMCPU_IS_6328())
-+ reg = MISC_SERDES_CTRL_6328_REG;
-+ else
-+ reg = MISC_SERDES_CTRL_6362_REG;
-+
-+ val = bcm_misc_readl(reg);
- val |= SERDES_PCIE_EN | SERDES_PCIE_EXD_EN;
-- bcm_misc_writel(val, MISC_SERDES_CTRL_REG);
-+ bcm_misc_writel(val, reg);
-
- /* reset the PCIe core */
- bcm63xx_core_set_reset(BCM63XX_RESET_PCIE, 1);
-@@ -330,6 +336,7 @@ static int __init bcm63xx_pci_init(void)
-
- switch (bcm63xx_get_cpu_id()) {
- case BCM6328_CPU_ID:
-+ case BCM6362_CPU_ID:
- return bcm63xx_register_pcie();
- case BCM6348_CPU_ID:
- case BCM6358_CPU_ID:
+++ /dev/null
-From 01034e48e72783ced82a050e862f82ee3dfdb783 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 21 Nov 2011 00:48:52 +0100
-Subject: [PATCH 7/7] MIPS: BCM63XX: add flash detection for BCM6362
-
-BCM6362 support booting from SPI flash and NAND.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/dev-flash.c | 6 ++++++
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 1 +
- 2 files changed, 7 insertions(+)
-
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -77,6 +77,12 @@ static int __init bcm63xx_detect_flash_t
- return BCM63XX_FLASH_TYPE_PARALLEL;
- else
- return BCM63XX_FLASH_TYPE_SERIAL;
-+ case BCM6362_CPU_ID:
-+ val = bcm_misc_readl(MISC_STRAPBUS_6362_REG);
-+ if (val & STRAPBUS_6362_BOOT_SEL_SERIAL)
-+ return BCM63XX_FLASH_TYPE_SERIAL;
-+ else
-+ return BCM63XX_FLASH_TYPE_NAND;
- case BCM6368_CPU_ID:
- val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
- switch (val & STRAPBUS_6368_BOOT_SEL_MASK) {
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -1372,6 +1372,7 @@
-
- #define MISC_STRAPBUS_6362_REG 0x14
- #define STRAPBUS_6362_FCVO_SHIFT 1
-+#define STRAPBUS_6362_HSSPI_CLK_FAST (1 << 13)
- #define STRAPBUS_6362_FCVO_MASK (0x1f << STRAPBUS_6362_FCVO_SHIFT)
- #define STRAPBUS_6362_BOOT_SEL_SERIAL (1 << 15)
- #define STRAPBUS_6362_BOOT_SEL_NAND (0 << 15)
+++ /dev/null
-From d31454bc822e1957e758e75d4367bcd12af89743 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Thu, 18 Apr 2013 21:23:11 +0200
-Subject: [PATCH] MIPS: BCM63XX: add missing clocks for BCM6328 and BCM6362
-
-Add currently unused missing clocks for BCM6328 and BCM6362.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/clk.c | 33 +++++++++++++++++++++++++--------
- 1 file changed, 25 insertions(+), 8 deletions(-)
-
---- a/arch/mips/bcm63xx/clk.c
-+++ b/arch/mips/bcm63xx/clk.c
-@@ -125,11 +125,18 @@ static struct clk clk_ephy = {
- */
- static void enetsw_set(struct clk *clk, int enable)
- {
-- if (!BCMCPU_IS_6368())
-+ if (BCMCPU_IS_6328())
-+ bcm_hwclock_set(CKCTL_6328_ROBOSW_EN, enable);
-+ else if (BCMCPU_IS_6362())
-+ bcm_hwclock_set(CKCTL_6362_ROBOSW_EN, enable);
-+ else if (BCMCPU_IS_6368())
-+ bcm_hwclock_set(CKCTL_6368_ROBOSW_EN |
-+ CKCTL_6368_SWPKT_USB_EN |
-+ CKCTL_6368_SWPKT_SAR_EN,
-+ enable);
-+ else
- return;
-- bcm_hwclock_set(CKCTL_6368_ROBOSW_EN |
-- CKCTL_6368_SWPKT_USB_EN |
-- CKCTL_6368_SWPKT_SAR_EN, enable);
-+
- if (enable) {
- /* reset switch core afer clock change */
- bcm63xx_core_set_reset(BCM63XX_RESET_ENETSW, 1);
-@@ -166,6 +173,8 @@ static void usbh_set(struct clk *clk, in
- bcm_hwclock_set(CKCTL_6328_USBH_EN, enable);
- else if (BCMCPU_IS_6348())
- bcm_hwclock_set(CKCTL_6348_USBH_EN, enable);
-+ else if (BCMCPU_IS_6362())
-+ bcm_hwclock_set(CKCTL_6362_USBH_EN, enable);
- else if (BCMCPU_IS_6368())
- bcm_hwclock_set(CKCTL_6368_USBH_EN, enable);
- }
-@@ -181,6 +190,8 @@ static void usbd_set(struct clk *clk, in
- {
- if (BCMCPU_IS_6328())
- bcm_hwclock_set(CKCTL_6328_USBD_EN, enable);
-+ else if (BCMCPU_IS_6362())
-+ bcm_hwclock_set(CKCTL_6362_USBD_EN, enable);
- else if (BCMCPU_IS_6368())
- bcm_hwclock_set(CKCTL_6368_USBD_EN, enable);
- }
-@@ -244,7 +255,10 @@ static struct clk clk_xtm = {
- */
- static void ipsec_set(struct clk *clk, int enable)
- {
-- bcm_hwclock_set(CKCTL_6368_IPSEC_EN, enable);
-+ if (BCMCPU_IS_6362())
-+ bcm_hwclock_set(CKCTL_6362_IPSEC_EN, enable);
-+ else if (BCMCPU_IS_6368())
-+ bcm_hwclock_set(CKCTL_6368_IPSEC_EN, enable);
- }
-
- static struct clk clk_ipsec = {
-@@ -257,7 +271,10 @@ static struct clk clk_ipsec = {
-
- static void pcie_set(struct clk *clk, int enable)
- {
-- bcm_hwclock_set(CKCTL_6328_PCIE_EN, enable);
-+ if (BCMCPU_IS_6328())
-+ bcm_hwclock_set(CKCTL_6328_PCIE_EN, enable);
-+ else if (BCMCPU_IS_6362())
-+ bcm_hwclock_set(CKCTL_6362_PCIE_EN, enable);
- }
-
- static struct clk clk_pcie = {
-@@ -323,9 +340,9 @@ struct clk *clk_get(struct device *dev,
- return &clk_periph;
- if (BCMCPU_IS_6358() && !strcmp(id, "pcm"))
- return &clk_pcm;
-- if (BCMCPU_IS_6368() && !strcmp(id, "ipsec"))
-+ if ((BCMCPU_IS_6362() || BCMCPU_IS_6368()) && !strcmp(id, "ipsec"))
- return &clk_ipsec;
-- if (BCMCPU_IS_6328() && !strcmp(id, "pcie"))
-+ if ((BCMCPU_IS_6328() || BCMCPU_IS_6362()) && !strcmp(id, "pcie"))
- return &clk_pcie;
- return ERR_PTR(-ENOENT);
- }
+++ /dev/null
-From e2092cf1b164ede62b740c7c95905171fb6232ff Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sat, 23 Mar 2013 12:32:56 +0100
-Subject: [PATCH v2 1/3] MTD: bcm63xxpart: use size macro for CFE block size
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/mtd/bcm63xxpart.c | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/drivers/mtd/bcm63xxpart.c
-+++ b/drivers/mtd/bcm63xxpart.c
-@@ -27,6 +27,7 @@
- #include <linux/crc32.h>
- #include <linux/module.h>
- #include <linux/kernel.h>
-+#include <linux/sizes.h>
- #include <linux/slab.h>
- #include <linux/vmalloc.h>
- #include <linux/mtd/mtd.h>
-@@ -37,7 +38,7 @@
-
- #define BCM63XX_EXTENDED_SIZE 0xBFC00000 /* Extended flash address */
-
--#define BCM63XX_CFE_BLOCK_SIZE 0x10000 /* always at least 64KiB */
-+#define BCM63XX_CFE_BLOCK_SIZE SZ_64K /* always at least 64KiB */
-
- #define BCM63XX_CFE_MAGIC_OFFSET 0x4e0
-
+++ /dev/null
-From bda508f975d1372568a4fc9862be501a6176fd46 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sat, 12 May 2012 23:04:17 +0200
-Subject: [PATCH v2 2/3] MIPS: BCM63XX: export PSI size from nvram
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/nvram.c | 13 +++++++++++++
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h | 7 +++++++
- 2 files changed, 20 insertions(+)
-
---- a/arch/mips/bcm63xx/nvram.c
-+++ b/arch/mips/bcm63xx/nvram.c
-@@ -15,6 +15,7 @@
- #include <linux/export.h>
- #include <linux/kernel.h>
- #include <linux/if_ether.h>
-+#include <linux/sizes.h>
-
- #include <bcm63xx_nvram.h>
-
-@@ -35,6 +36,8 @@ struct bcm963xx_nvram {
- u32 checksum_high;
- };
-
-+#define BCM63XX_DEFAULT_PSI_SIZE SZ_64K
-+
- static struct bcm963xx_nvram nvram;
- static int mac_addr_used;
-
-@@ -104,3 +107,13 @@ int bcm63xx_nvram_get_mac_address(u8 *ma
- return 0;
- }
- EXPORT_SYMBOL(bcm63xx_nvram_get_mac_address);
-+
-+unsigned int bcm63xx_nvram_get_psi_size(void)
-+{
-+ /* max is 64k, but some vendors use higher values */
-+ if (nvram.psi_size > 0 && nvram.psi_size <= 512)
-+ return nvram.psi_size * SZ_1K;
-+
-+ return BCM63XX_DEFAULT_PSI_SIZE;
-+}
-+EXPORT_SYMBOL(bcm63xx_nvram_get_psi_size);
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_nvram.h
-@@ -30,4 +30,11 @@ u8 *bcm63xx_nvram_get_name(void);
- */
- int bcm63xx_nvram_get_mac_address(u8 *mac);
-
-+/**
-+ * bcm63xx_nvram_get_psi_size() - returns the size of the PSI area
-+ *
-+ * Returns the size of the Persitent Storage Information area in bytes.
-+ */
-+unsigned int bcm63xx_nvram_get_psi_size(void);
-+
- #endif /* BCM63XX_NVRAM_H */
+++ /dev/null
-From f6eefaa4a08ec27c69485c2fc4db23247b84f8c9 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Tue, 1 May 2012 14:10:39 +0200
-Subject: [PATCH v2 3/3] MTD: bcm63xxpart: use nvram for PSI size
-
-Read out the SPI size from nvram instead of defaulting to 64K - some
-vendors actually use values larger than the "max" value of 64.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- drivers/mtd/bcm63xxpart.c | 6 ++++--
- 1 file changed, 4 insertions(+), 2 deletions(-)
-
---- a/drivers/mtd/bcm63xxpart.c
-+++ b/drivers/mtd/bcm63xxpart.c
-@@ -4,7 +4,7 @@
- * Copyright © 2006-2008 Florian Fainelli <florian@openwrt.org>
- * Mike Albon <malbon@openwrt.org>
- * Copyright © 2009-2010 Daniel Dickinson <openwrt@cshore.neomailbox.net>
-- * Copyright © 2011-2012 Jonas Gorski <jonas.gorski@gmail.com>
-+ * Copyright © 2011-2013 Jonas Gorski <jonas.gorski@gmail.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
-@@ -34,6 +34,7 @@
- #include <linux/mtd/partitions.h>
-
- #include <linux/bcm963xx_tag.h>
-+#include <asm/mach-bcm63xx/bcm63xx_nvram.h>
- #include <asm/mach-bcm63xx/board_bcm963xx.h>
-
- #define BCM63XX_EXTENDED_SIZE 0xBFC00000 /* Extended flash address */
-@@ -91,7 +92,8 @@ static int bcm63xx_parse_cfe_partitions(
- BCM63XX_CFE_BLOCK_SIZE);
-
- cfelen = cfe_erasesize;
-- nvramlen = cfe_erasesize;
-+ nvramlen = bcm63xx_nvram_get_psi_size();
-+ nvramlen = roundup(nvramlen, cfe_erasesize);
-
- /* Allocate memory for buffer */
- buf = vmalloc(sizeof(struct bcm_tag));
+++ /dev/null
-From 80a2f983e9f44dbc3e01ae31c62d877846a7f791 Mon Sep 17 00:00:00 2001
-From: Florian Fainelli <florian@openwrt.org>
-Date: Mon, 28 Jan 2013 20:06:19 +0100
-Subject: [PATCH 01/11] MIPS: BCM63XX: add USB host clock enable delay
-
-Knowledge of the clock setup delay should remain at the clock level (so
-it can be clock specific and CPU specific). Add the 100 milliseconds
-required clock delay for the USB host clock when it gets enabled.
-
-Signed-off-by: Florian Fainelli <florian@openwrt.org>
----
- arch/mips/bcm63xx/clk.c | 5 +++++
- 1 file changed, 5 insertions(+)
-
---- a/arch/mips/bcm63xx/clk.c
-+++ b/arch/mips/bcm63xx/clk.c
-@@ -177,6 +177,11 @@ static void usbh_set(struct clk *clk, in
- bcm_hwclock_set(CKCTL_6362_USBH_EN, enable);
- else if (BCMCPU_IS_6368())
- bcm_hwclock_set(CKCTL_6368_USBH_EN, enable);
-+ else
-+ return;
-+
-+ if (enable)
-+ msleep(100);
- }
-
- static struct clk clk_usbh = {
+++ /dev/null
-From 8e9bf528a122741f0171b89c297b63041116d704 Mon Sep 17 00:00:00 2001
-From: Florian Fainelli <florian@openwrt.org>
-Date: Mon, 28 Jan 2013 20:06:20 +0100
-Subject: [PATCH 02/11] MIPS: BCM63XX: add USB device clock enable delay to
- clock code
-
-This patch adds the required 10 micro seconds delay to the USB device
-clock enable operation. Put this where the correct clock knowledege is,
-which is in the clock code, and remove this delay from the bcm63xx_udc
-gadget driver where it was before.
-
-Signed-off-by: Florian Fainelli <florian@openwrt.org>
----
- arch/mips/bcm63xx/clk.c | 5 +++++
- drivers/usb/gadget/bcm63xx_udc.c | 1 -
- 2 files changed, 5 insertions(+), 1 deletion(-)
-
---- a/arch/mips/bcm63xx/clk.c
-+++ b/arch/mips/bcm63xx/clk.c
-@@ -199,6 +199,11 @@ static void usbd_set(struct clk *clk, in
- bcm_hwclock_set(CKCTL_6362_USBD_EN, enable);
- else if (BCMCPU_IS_6368())
- bcm_hwclock_set(CKCTL_6368_USBD_EN, enable);
-+ else
-+ return;
-+
-+ if (enable)
-+ udelay(10);
- }
-
- static struct clk clk_usbd = {
---- a/drivers/usb/gadget/bcm63xx_udc.c
-+++ b/drivers/usb/gadget/bcm63xx_udc.c
-@@ -386,7 +386,6 @@ static inline void set_clocks(struct bcm
- if (is_enabled) {
- clk_enable(udc->usbh_clk);
- clk_enable(udc->usbd_clk);
-- udelay(10);
- } else {
- clk_disable(udc->usbd_clk);
- clk_disable(udc->usbh_clk);
+++ /dev/null
-From ac9b0b574d54be28b300bf99ffe092a2c589484f Mon Sep 17 00:00:00 2001
-From: Florian Fainelli <florian@openwrt.org>
-Date: Mon, 28 Jan 2013 20:06:21 +0100
-Subject: [PATCH 03/11] MIPS: BCM63XX: move code touching the USB private
- register
-
-This patch moves the code touching the USB private register in the
-bcm63xx USB gadget driver to arch/mips/bcm63xx/usb-common.c in
-preparation for adding support for OHCI and EHCI host controllers which
-will also touch the USB private register.
-
-Signed-off-by: Florian Fainelli <florian@openwrt.org>
----
- arch/mips/bcm63xx/Makefile | 2 +-
- arch/mips/bcm63xx/usb-common.c | 53 ++++++++++++++++++++
- .../include/asm/mach-bcm63xx/bcm63xx_usb_priv.h | 9 ++++
- drivers/usb/gadget/bcm63xx_udc.c | 27 ++--------
- 4 files changed, 67 insertions(+), 24 deletions(-)
- create mode 100644 arch/mips/bcm63xx/usb-common.c
- create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h
-
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,7 +1,7 @@
- obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \
- setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
- dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \
-- dev-usb-usbd.o
-+ dev-usb-usbd.o usb-common.o
- obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
-
- obj-y += boards/
---- /dev/null
-+++ b/arch/mips/bcm63xx/usb-common.c
-@@ -0,0 +1,53 @@
-+/*
-+ * Broadcom BCM63xx common USB device configuration code
-+ *
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2012 Kevin Cernekee <cernekee@gmail.com>
-+ * Copyright (C) 2012 Broadcom Corporation
-+ *
-+ */
-+#include <linux/export.h>
-+
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_regs.h>
-+#include <bcm63xx_io.h>
-+#include <bcm63xx_usb_priv.h>
-+
-+void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device)
-+{
-+ u32 val;
-+
-+ val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
-+ if (is_device) {
-+ val |= (portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT);
-+ val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
-+ } else {
-+ val &= ~(portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT);
-+ val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
-+ }
-+ bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG);
-+
-+ val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG);
-+ if (is_device)
-+ val |= USBH_PRIV_SWAP_USBD_MASK;
-+ else
-+ val &= ~USBH_PRIV_SWAP_USBD_MASK;
-+ bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG);
-+}
-+EXPORT_SYMBOL(bcm63xx_usb_priv_select_phy_mode);
-+
-+void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on)
-+{
-+ u32 val;
-+
-+ val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
-+ if (is_on)
-+ val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
-+ else
-+ val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
-+ bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG);
-+}
-+EXPORT_SYMBOL(bcm63xx_usb_priv_select_pullup);
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h
-@@ -0,0 +1,9 @@
-+#ifndef BCM63XX_USB_PRIV_H_
-+#define BCM63XX_USB_PRIV_H_
-+
-+#include <linux/types.h>
-+
-+void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device);
-+void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on);
-+
-+#endif /* BCM63XX_USB_PRIV_H_ */
---- a/drivers/usb/gadget/bcm63xx_udc.c
-+++ b/drivers/usb/gadget/bcm63xx_udc.c
-@@ -41,6 +41,7 @@
- #include <bcm63xx_dev_usb_usbd.h>
- #include <bcm63xx_io.h>
- #include <bcm63xx_regs.h>
-+#include <bcm63xx_usb_priv.h>
-
- #define DRV_MODULE_NAME "bcm63xx_udc"
-
-@@ -863,22 +864,7 @@ static void bcm63xx_select_phy_mode(stru
- bcm_gpio_writel(val, GPIO_PINMUX_OTHR_REG);
- }
-
-- val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
-- if (is_device) {
-- val |= (portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT);
-- val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
-- } else {
-- val &= ~(portmask << USBH_PRIV_UTMI_CTL_HOSTB_SHIFT);
-- val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
-- }
-- bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG);
--
-- val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG);
-- if (is_device)
-- val |= USBH_PRIV_SWAP_USBD_MASK;
-- else
-- val &= ~USBH_PRIV_SWAP_USBD_MASK;
-- bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG);
-+ bcm63xx_usb_priv_select_phy_mode(portmask, is_device);
- }
-
- /**
-@@ -892,14 +878,9 @@ static void bcm63xx_select_phy_mode(stru
- */
- static void bcm63xx_select_pullup(struct bcm63xx_udc *udc, bool is_on)
- {
-- u32 val, portmask = BIT(udc->pd->port_no);
-+ u32 portmask = BIT(udc->pd->port_no);
-
-- val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
-- if (is_on)
-- val &= ~(portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
-- else
-- val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
-- bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG);
-+ bcm63xx_usb_priv_select_pullup(portmask, is_on);
- }
-
- /**
+++ /dev/null
-From 28758a9da77954ed323f86123ef448c6a563c037 Mon Sep 17 00:00:00 2001
-From: Florian Fainelli <florian@openwrt.org>
-Date: Mon, 28 Jan 2013 20:06:22 +0100
-Subject: [PATCH 04/11] MIPS: BCM63XX: add OHCI/EHCI configuration bits to
- common USB code
-
-This patch updates the common USB code touching the USB private
-registers with the specific bits to properly enable OHCI and EHCI
-controllers on BCM63xx SoCs. As a result we now need to protect access
-to Read Modify Write sequences using a spinlock because we cannot
-guarantee that any of the exposed helper will not be called
-concurrently.
-
-Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
-Signed-off-by: Florian Fainelli <florian@openwrt.org>
----
- arch/mips/bcm63xx/usb-common.c | 97 ++++++++++++++++++++
- .../include/asm/mach-bcm63xx/bcm63xx_usb_priv.h | 2 +
- 2 files changed, 99 insertions(+)
-
---- a/arch/mips/bcm63xx/usb-common.c
-+++ b/arch/mips/bcm63xx/usb-common.c
-@@ -5,10 +5,12 @@
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- *
-+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
- * Copyright (C) 2012 Kevin Cernekee <cernekee@gmail.com>
- * Copyright (C) 2012 Broadcom Corporation
- *
- */
-+#include <linux/spinlock.h>
- #include <linux/export.h>
-
- #include <bcm63xx_cpu.h>
-@@ -16,9 +18,14 @@
- #include <bcm63xx_io.h>
- #include <bcm63xx_usb_priv.h>
-
-+static DEFINE_SPINLOCK(usb_priv_reg_lock);
-+
- void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device)
- {
- u32 val;
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&usb_priv_reg_lock, flags);
-
- val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
- if (is_device) {
-@@ -36,12 +43,17 @@ void bcm63xx_usb_priv_select_phy_mode(u3
- else
- val &= ~USBH_PRIV_SWAP_USBD_MASK;
- bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_SWAP_6368_REG);
-+
-+ spin_unlock_irqrestore(&usb_priv_reg_lock, flags);
- }
- EXPORT_SYMBOL(bcm63xx_usb_priv_select_phy_mode);
-
- void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on)
- {
- u32 val;
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&usb_priv_reg_lock, flags);
-
- val = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_UTMI_CTL_6368_REG);
- if (is_on)
-@@ -49,5 +61,90 @@ void bcm63xx_usb_priv_select_pullup(u32
- else
- val |= (portmask << USBH_PRIV_UTMI_CTL_NODRIV_SHIFT);
- bcm_rset_writel(RSET_USBH_PRIV, val, USBH_PRIV_UTMI_CTL_6368_REG);
-+
-+ spin_unlock_irqrestore(&usb_priv_reg_lock, flags);
- }
- EXPORT_SYMBOL(bcm63xx_usb_priv_select_pullup);
-+
-+/* The following array represents the meaning of the DESC/DATA
-+ * endian swapping with respect to the CPU configured endianness
-+ *
-+ * DATA ENDN mmio descriptor
-+ * 0 0 BE invalid
-+ * 0 1 BE LE
-+ * 1 0 BE BE
-+ * 1 1 BE invalid
-+ *
-+ * Since BCM63XX SoCs are configured to be in big-endian mode
-+ * we want configuration at line 3.
-+ */
-+void bcm63xx_usb_priv_ohci_cfg_set(void)
-+{
-+ u32 reg;
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&usb_priv_reg_lock, flags);
-+
-+ if (BCMCPU_IS_6348())
-+ bcm_rset_writel(RSET_OHCI_PRIV, 0, OHCI_PRIV_REG);
-+ else if (BCMCPU_IS_6358()) {
-+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6358_REG);
-+ reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK;
-+ reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK;
-+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6358_REG);
-+ /*
-+ * The magic value comes for the original vendor BSP
-+ * and is needed for USB to work. Datasheet does not
-+ * help, so the magic value is used as-is.
-+ */
-+ bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020,
-+ USBH_PRIV_TEST_6358_REG);
-+
-+ } else if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) {
-+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG);
-+ reg &= ~USBH_PRIV_SWAP_OHCI_ENDN_MASK;
-+ reg |= USBH_PRIV_SWAP_OHCI_DATA_MASK;
-+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG);
-+
-+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG);
-+ reg |= USBH_PRIV_SETUP_IOC_MASK;
-+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG);
-+ }
-+
-+ spin_unlock_irqrestore(&usb_priv_reg_lock, flags);
-+}
-+
-+void bcm63xx_usb_priv_ehci_cfg_set(void)
-+{
-+ u32 reg;
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&usb_priv_reg_lock, flags);
-+
-+ if (BCMCPU_IS_6358()) {
-+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6358_REG);
-+ reg &= ~USBH_PRIV_SWAP_EHCI_ENDN_MASK;
-+ reg |= USBH_PRIV_SWAP_EHCI_DATA_MASK;
-+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6358_REG);
-+
-+ /*
-+ * The magic value comes for the original vendor BSP
-+ * and is needed for USB to work. Datasheet does not
-+ * help, so the magic value is used as-is.
-+ */
-+ bcm_rset_writel(RSET_USBH_PRIV, 0x1c0020,
-+ USBH_PRIV_TEST_6358_REG);
-+
-+ } else if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) {
-+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SWAP_6368_REG);
-+ reg &= ~USBH_PRIV_SWAP_EHCI_ENDN_MASK;
-+ reg |= USBH_PRIV_SWAP_EHCI_DATA_MASK;
-+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SWAP_6368_REG);
-+
-+ reg = bcm_rset_readl(RSET_USBH_PRIV, USBH_PRIV_SETUP_6368_REG);
-+ reg |= USBH_PRIV_SETUP_IOC_MASK;
-+ bcm_rset_writel(RSET_USBH_PRIV, reg, USBH_PRIV_SETUP_6368_REG);
-+ }
-+
-+ spin_unlock_irqrestore(&usb_priv_reg_lock, flags);
-+}
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_usb_priv.h
-@@ -5,5 +5,7 @@
-
- void bcm63xx_usb_priv_select_phy_mode(u32 portmask, bool is_device);
- void bcm63xx_usb_priv_select_pullup(u32 portmask, bool is_on);
-+void bcm63xx_usb_priv_ohci_cfg_set(void);
-+void bcm63xx_usb_priv_ehci_cfg_set(void);
-
- #endif /* BCM63XX_USB_PRIV_H_ */
+++ /dev/null
-From 94ec618bd1a6b07fafbbfc9bcc54e7f9360ff9a0 Mon Sep 17 00:00:00 2001
-From: Florian Fainelli <florian@openwrt.org>
-Date: Mon, 28 Jan 2013 20:06:23 +0100
-Subject: [PATCH 05/11] MIPS: BCM63XX: introduce BCM63XX_OHCI configuration
- symbol
-
-This configuration symbol can be used by CPUs supporting the on-chip
-OHCI controller, and ensures that all relevant OHCI-related
-configuration options are correctly selected. So far, OHCI support is
-available for the 6328, 6348, 6358 and 6358 SoCs.
-
-Signed-off-by: Florian Fainelli <florian@openwrt.org>
----
- arch/mips/bcm63xx/Kconfig | 15 ++++++++++-----
- 1 file changed, 10 insertions(+), 5 deletions(-)
-
---- a/arch/mips/bcm63xx/Kconfig
-+++ b/arch/mips/bcm63xx/Kconfig
-@@ -1,37 +1,43 @@
- menu "CPU support"
- depends on BCM63XX
-
-+config BCM63XX_OHCI
-+ bool
-+ select USB_ARCH_HAS_OHCI
-+ select USB_OHCI_BIG_ENDIAN_DESC if USB_OHCI_HCD
-+ select USB_OHCI_BIG_ENDIAN_MMIO if USB_OHCI_HCD
-+
- config BCM63XX_CPU_6328
- bool "support 6328 CPU"
- select HW_HAS_PCI
-+ select BCM63XX_OHCI
-
- config BCM63XX_CPU_6338
- bool "support 6338 CPU"
- select HW_HAS_PCI
-- select USB_ARCH_HAS_OHCI
-- select USB_OHCI_BIG_ENDIAN_DESC
-- select USB_OHCI_BIG_ENDIAN_MMIO
-
- config BCM63XX_CPU_6345
- bool "support 6345 CPU"
-- select USB_OHCI_BIG_ENDIAN_DESC
-- select USB_OHCI_BIG_ENDIAN_MMIO
-
- config BCM63XX_CPU_6348
- bool "support 6348 CPU"
- select HW_HAS_PCI
-+ select BCM63XX_OHCI
-
- config BCM63XX_CPU_6358
- bool "support 6358 CPU"
- select HW_HAS_PCI
-+ select BCM63XX_OHCI
-
- config BCM63XX_CPU_6362
- bool "support 6362 CPU"
- select HW_HAS_PCI
-+ select BCM63XX_OHCI
-
- config BCM63XX_CPU_6368
- bool "support 6368 CPU"
- select HW_HAS_PCI
-+ select BCM63XX_OHCI
- endmenu
-
- source "arch/mips/bcm63xx/boards/Kconfig"
+++ /dev/null
-From 30d22baef255c99a12c4858ce4ab0d45f0d8c9ae Mon Sep 17 00:00:00 2001
-From: Florian Fainelli <florian@openwrt.org>
-Date: Mon, 28 Jan 2013 20:06:24 +0100
-Subject: [PATCH 06/11] MIPS: BCM63XX: add support for the on-chip OHCI
- controller
-
-Broadcom BCM63XX SoCs include an on-chip OHCI controller which can be
-driven by the ohci-platform generic driver by using specific power
-on/off/suspend callback to manage clocks and hardware specific
-configuration.
-
-Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
-Signed-off-by: Florian Fainelli <florian@openwrt.org>
----
- arch/mips/bcm63xx/Makefile | 2 +-
- arch/mips/bcm63xx/dev-usb-ohci.c | 94 ++++++++++++++++++++
- .../asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h | 6 ++
- 3 files changed, 101 insertions(+), 1 deletion(-)
- create mode 100644 arch/mips/bcm63xx/dev-usb-ohci.c
- create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h
-
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,7 +1,7 @@
- obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \
- setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
- dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \
-- dev-usb-usbd.o usb-common.o
-+ dev-usb-ohci.o dev-usb-usbd.o usb-common.o
- obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
-
- obj-y += boards/
---- /dev/null
-+++ b/arch/mips/bcm63xx/dev-usb-ohci.c
-@@ -0,0 +1,94 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
-+ * Copyright (C) 2013 Florian Fainelli <florian@openwrt.org>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+#include <linux/usb/ohci_pdriver.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/clk.h>
-+#include <linux/delay.h>
-+
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_regs.h>
-+#include <bcm63xx_io.h>
-+#include <bcm63xx_usb_priv.h>
-+#include <bcm63xx_dev_usb_ohci.h>
-+
-+static struct resource ohci_resources[] = {
-+ {
-+ .start = -1, /* filled at runtime */
-+ .end = -1, /* filled at runtime */
-+ .flags = IORESOURCE_MEM,
-+ },
-+ {
-+ .start = -1, /* filled at runtime */
-+ .flags = IORESOURCE_IRQ,
-+ },
-+};
-+
-+static u64 ohci_dmamask = DMA_BIT_MASK(32);
-+
-+static struct clk *usb_host_clock;
-+
-+static int bcm63xx_ohci_power_on(struct platform_device *pdev)
-+{
-+ usb_host_clock = clk_get(&pdev->dev, "usbh");
-+ if (IS_ERR_OR_NULL(usb_host_clock))
-+ return -ENODEV;
-+
-+ clk_prepare_enable(usb_host_clock);
-+
-+ bcm63xx_usb_priv_ohci_cfg_set();
-+
-+ return 0;
-+}
-+
-+static void bcm63xx_ohci_power_off(struct platform_device *pdev)
-+{
-+ if (!IS_ERR_OR_NULL(usb_host_clock)) {
-+ clk_disable_unprepare(usb_host_clock);
-+ clk_put(usb_host_clock);
-+ }
-+}
-+
-+static struct usb_ohci_pdata bcm63xx_ohci_pdata = {
-+ .big_endian_desc = 1,
-+ .big_endian_mmio = 1,
-+ .no_big_frame_no = 1,
-+ .num_ports = 1,
-+ .power_on = bcm63xx_ohci_power_on,
-+ .power_off = bcm63xx_ohci_power_off,
-+ .power_suspend = bcm63xx_ohci_power_off,
-+};
-+
-+static struct platform_device bcm63xx_ohci_device = {
-+ .name = "ohci-platform",
-+ .id = -1,
-+ .num_resources = ARRAY_SIZE(ohci_resources),
-+ .resource = ohci_resources,
-+ .dev = {
-+ .platform_data = &bcm63xx_ohci_pdata,
-+ .dma_mask = &ohci_dmamask,
-+ .coherent_dma_mask = DMA_BIT_MASK(32),
-+ },
-+};
-+
-+int __init bcm63xx_ohci_register(void)
-+{
-+ if (BCMCPU_IS_6345() || BCMCPU_IS_6338())
-+ return -ENODEV;
-+
-+ ohci_resources[0].start = bcm63xx_regset_address(RSET_OHCI0);
-+ ohci_resources[0].end = ohci_resources[0].start;
-+ ohci_resources[0].end += RSET_OHCI_SIZE - 1;
-+ ohci_resources[1].start = bcm63xx_get_irq_number(IRQ_OHCI0);
-+
-+ return platform_device_register(&bcm63xx_ohci_device);
-+}
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ohci.h
-@@ -0,0 +1,6 @@
-+#ifndef BCM63XX_DEV_USB_OHCI_H_
-+#define BCM63XX_DEV_USB_OHCI_H_
-+
-+int bcm63xx_ohci_register(void);
-+
-+#endif /* BCM63XX_DEV_USB_OHCI_H_ */
+++ /dev/null
-From 33ef960aed15f9a98a2c51d8d794cd72418e0be4 Mon Sep 17 00:00:00 2001
-From: Florian Fainelli <florian@openwrt.org>
-Date: Mon, 28 Jan 2013 20:06:25 +0100
-Subject: [PATCH 07/11] MIPS: BCM63XX: register OHCI controller if board
- enables it
-
-BCM63XX-based boards can control the registration of the OHCI controller
-by setting their has_ohci0 flag to 1. Handle this in the generic
-code dealing with board registration and call the actual helper to
-register the OHCI controller.
-
-Signed-off-by: Florian Fainelli <florian@openwrt.org>
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 4 ++++
- 1 file changed, 4 insertions(+)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -25,6 +25,7 @@
- #include <bcm63xx_dev_flash.h>
- #include <bcm63xx_dev_pcmcia.h>
- #include <bcm63xx_dev_spi.h>
-+#include <bcm63xx_dev_usb_ohci.h>
- #include <bcm63xx_dev_usb_usbd.h>
- #include <board_bcm963xx.h>
-
-@@ -848,6 +849,9 @@ int __init board_register_devices(void)
- if (board.has_usbd)
- bcm63xx_usbd_register(&board.usbd);
-
-+ if (board.has_ohci0)
-+ bcm63xx_ohci_register();
-+
- if (board.has_dsp)
- bcm63xx_dsp_register(&board.dsp);
-
+++ /dev/null
-From 00da1683364e58c6430a4577123d01037f8faddc Mon Sep 17 00:00:00 2001
-From: Florian Fainelli <florian@openwrt.org>
-Date: Mon, 28 Jan 2013 20:06:26 +0100
-Subject: [PATCH 08/11] MIPS: BCM63XX: introduce BCM63XX_EHCI configuration
- symbol
-
-This configuration symbol can be used by CPUs supporting the on-chip
-EHCI controller, and ensures that all relevant EHCI-related
-configuration options are selected. So far BCM6328, BCM6358 and BCM6368
-have an EHCI controller and do select this symbol. Update
-drivers/usb/host/Kconfig with BCM63XX to update direct unmet
-dependencies.
-
-Signed-off-by: Florian Fainelli <florian@openwrt.org>
----
- arch/mips/bcm63xx/Kconfig | 9 +++++++++
- drivers/usb/host/Kconfig | 5 +++--
- 2 files changed, 12 insertions(+), 2 deletions(-)
-
---- a/arch/mips/bcm63xx/Kconfig
-+++ b/arch/mips/bcm63xx/Kconfig
-@@ -7,10 +7,17 @@ config BCM63XX_OHCI
- select USB_OHCI_BIG_ENDIAN_DESC if USB_OHCI_HCD
- select USB_OHCI_BIG_ENDIAN_MMIO if USB_OHCI_HCD
-
-+config BCM63XX_EHCI
-+ bool
-+ select USB_ARCH_HAS_EHCI
-+ select USB_EHCI_BIG_ENDIAN_DESC if USB_EHCI_HCD
-+ select USB_EHCI_BIG_ENDIAN_MMIO if USB_EHCI_HCD
-+
- config BCM63XX_CPU_6328
- bool "support 6328 CPU"
- select HW_HAS_PCI
- select BCM63XX_OHCI
-+ select BCM63XX_EHCI
-
- config BCM63XX_CPU_6338
- bool "support 6338 CPU"
-@@ -28,16 +35,19 @@ config BCM63XX_CPU_6358
- bool "support 6358 CPU"
- select HW_HAS_PCI
- select BCM63XX_OHCI
-+ select BCM63XX_EHCI
-
- config BCM63XX_CPU_6362
- bool "support 6362 CPU"
- select HW_HAS_PCI
- select BCM63XX_OHCI
-+ select BCM63XX_EHCI
-
- config BCM63XX_CPU_6368
- bool "support 6368 CPU"
- select HW_HAS_PCI
- select BCM63XX_OHCI
-+ select BCM63XX_EHCI
- endmenu
-
- source "arch/mips/bcm63xx/boards/Kconfig"
---- a/drivers/usb/host/Kconfig
-+++ b/drivers/usb/host/Kconfig
-@@ -115,14 +115,15 @@ config USB_EHCI_BIG_ENDIAN_MMIO
- depends on USB_EHCI_HCD && (PPC_CELLEB || PPC_PS3 || 440EPX || \
- ARCH_IXP4XX || XPS_USB_HCD_XILINX || \
- PPC_MPC512x || CPU_CAVIUM_OCTEON || \
-- PMC_MSP || SPARC_LEON || MIPS_SEAD3)
-+ PMC_MSP || SPARC_LEON || MIPS_SEAD3 || \
-+ BCM63XX)
- default y
-
- config USB_EHCI_BIG_ENDIAN_DESC
- bool
- depends on USB_EHCI_HCD && (440EPX || ARCH_IXP4XX || XPS_USB_HCD_XILINX || \
- PPC_MPC512x || PMC_MSP || SPARC_LEON || \
-- MIPS_SEAD3)
-+ MIPS_SEAD3 || BCM63XX)
- default y
-
- config XPS_USB_HCD_XILINX
+++ /dev/null
-From e38f13bd6408769c0b565bb1079024f496eee121 Mon Sep 17 00:00:00 2001
-From: Florian Fainelli <florian@openwrt.org>
-Date: Mon, 28 Jan 2013 20:06:27 +0100
-Subject: [PATCH 09/11] MIPS: BCM63XX: add support for the on-chip EHCI
- controller
-
-Broadcom BCM63XX SoCs include an on-chip EHCI controller which can be
-driven by the generic ehci-platform driver by using specific power
-on/off/suspend callbacks to manage clocks and hardware specific
-configuration.
-
-Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
-Signed-off-by: Florian Fainelli <florian@openwrt.org>
----
- arch/mips/bcm63xx/Makefile | 2 +-
- arch/mips/bcm63xx/dev-usb-ehci.c | 92 ++++++++++++++++++++
- .../asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h | 6 ++
- 3 files changed, 99 insertions(+), 1 deletion(-)
- create mode 100644 arch/mips/bcm63xx/dev-usb-ehci.c
- create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h
-
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,7 +1,7 @@
- obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \
- setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
- dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \
-- dev-usb-ohci.o dev-usb-usbd.o usb-common.o
-+ dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o usb-common.o
- obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
-
- obj-y += boards/
---- /dev/null
-+++ b/arch/mips/bcm63xx/dev-usb-ehci.c
-@@ -0,0 +1,92 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr>
-+ * Copyright (C) 2013 Florian Fainelli <florian@openwrt.org>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+#include <linux/clk.h>
-+#include <linux/delay.h>
-+#include <linux/usb/ehci_pdriver.h>
-+#include <linux/dma-mapping.h>
-+
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_regs.h>
-+#include <bcm63xx_io.h>
-+#include <bcm63xx_usb_priv.h>
-+#include <bcm63xx_dev_usb_ehci.h>
-+
-+static struct resource ehci_resources[] = {
-+ {
-+ .start = -1, /* filled at runtime */
-+ .end = -1, /* filled at runtime */
-+ .flags = IORESOURCE_MEM,
-+ },
-+ {
-+ .start = -1, /* filled at runtime */
-+ .flags = IORESOURCE_IRQ,
-+ },
-+};
-+
-+static u64 ehci_dmamask = DMA_BIT_MASK(32);
-+
-+static struct clk *usb_host_clock;
-+
-+static int bcm63xx_ehci_power_on(struct platform_device *pdev)
-+{
-+ usb_host_clock = clk_get(&pdev->dev, "usbh");
-+ if (IS_ERR_OR_NULL(usb_host_clock))
-+ return -ENODEV;
-+
-+ clk_prepare_enable(usb_host_clock);
-+
-+ bcm63xx_usb_priv_ehci_cfg_set();
-+
-+ return 0;
-+}
-+
-+static void bcm63xx_ehci_power_off(struct platform_device *pdev)
-+{
-+ if (!IS_ERR_OR_NULL(usb_host_clock)) {
-+ clk_disable_unprepare(usb_host_clock);
-+ clk_put(usb_host_clock);
-+ }
-+}
-+
-+static struct usb_ehci_pdata bcm63xx_ehci_pdata = {
-+ .big_endian_desc = 1,
-+ .big_endian_mmio = 1,
-+ .power_on = bcm63xx_ehci_power_on,
-+ .power_off = bcm63xx_ehci_power_off,
-+ .power_suspend = bcm63xx_ehci_power_off,
-+};
-+
-+static struct platform_device bcm63xx_ehci_device = {
-+ .name = "ehci-platform",
-+ .id = -1,
-+ .num_resources = ARRAY_SIZE(ehci_resources),
-+ .resource = ehci_resources,
-+ .dev = {
-+ .platform_data = &bcm63xx_ehci_pdata,
-+ .dma_mask = &ehci_dmamask,
-+ .coherent_dma_mask = DMA_BIT_MASK(32),
-+ },
-+};
-+
-+int __init bcm63xx_ehci_register(void)
-+{
-+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6358() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368())
-+ return 0;
-+
-+ ehci_resources[0].start = bcm63xx_regset_address(RSET_EHCI0);
-+ ehci_resources[0].end = ehci_resources[0].start;
-+ ehci_resources[0].end += RSET_EHCI_SIZE - 1;
-+ ehci_resources[1].start = bcm63xx_get_irq_number(IRQ_EHCI0);
-+
-+ return platform_device_register(&bcm63xx_ehci_device);
-+}
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_usb_ehci.h
-@@ -0,0 +1,6 @@
-+#ifndef BCM63XX_DEV_USB_EHCI_H_
-+#define BCM63XX_DEV_USB_EHCI_H_
-+
-+int bcm63xx_ehci_register(void);
-+
-+#endif /* BCM63XX_DEV_USB_EHCI_H_ */
+++ /dev/null
-From 709ef2034f5ba06da35f89856ad7baf2b7a41287 Mon Sep 17 00:00:00 2001
-From: Florian Fainelli <florian@openwrt.org>
-Date: Mon, 28 Jan 2013 20:06:28 +0100
-Subject: [PATCH 10/11] MIPS: BCM63XX: register EHCI controller if board
- enables it
-
-BCM63XX-based board can control the registration of the EHCI controller
-by setting their has_ehci0 flag to 1. Handle this in the generic
-code dealing with board registration and call the actual helper to register
-the EHCI controller.
-
-Signed-off-by: Florian Fainelli <florian@openwrt.org>
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 4 ++++
- 1 file changed, 4 insertions(+)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -25,6 +25,7 @@
- #include <bcm63xx_dev_flash.h>
- #include <bcm63xx_dev_pcmcia.h>
- #include <bcm63xx_dev_spi.h>
-+#include <bcm63xx_dev_usb_ehci.h>
- #include <bcm63xx_dev_usb_ohci.h>
- #include <bcm63xx_dev_usb_usbd.h>
- #include <board_bcm963xx.h>
-@@ -849,6 +850,9 @@ int __init board_register_devices(void)
- if (board.has_usbd)
- bcm63xx_usbd_register(&board.usbd);
-
-+ if (board.has_ehci0)
-+ bcm63xx_ehci_register();
-+
- if (board.has_ohci0)
- bcm63xx_ohci_register();
-
+++ /dev/null
-From 111bbd770441ab34f9da5bb1d85767a9b75227b4 Mon Sep 17 00:00:00 2001
-From: Florian Fainelli <florian@openwrt.org>
-Date: Mon, 28 Jan 2013 20:06:30 +0100
-Subject: [PATCH 12/12] MIPS: BCM63XX: EHCI controller does not support
- overcurrent
-
-This patch sets the ignore_oc flag for the BCM63XX EHCI controller as it
-does not support proper overcurrent reporting.
-
-Signed-off-by: Florian Fainelli <florian@openwrt.org>
----
- arch/mips/bcm63xx/dev-usb-ehci.c | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/arch/mips/bcm63xx/dev-usb-ehci.c
-+++ b/arch/mips/bcm63xx/dev-usb-ehci.c
-@@ -61,6 +61,7 @@ static void bcm63xx_ehci_power_off(struc
- static struct usb_ehci_pdata bcm63xx_ehci_pdata = {
- .big_endian_desc = 1,
- .big_endian_mmio = 1,
-+ .ignore_oc = 1,
- .power_on = bcm63xx_ehci_power_on,
- .power_off = bcm63xx_ehci_power_off,
- .power_suspend = bcm63xx_ehci_power_off,
+++ /dev/null
-From 3f650fc30aa0badf9d02842ce396cea3eef2eeaa Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Fri, 1 Jul 2011 23:16:47 +0200
-Subject: [PATCH 49/79] SPI: Allow specifying the parsers for SPI flash
-
-Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
----
- include/linux/spi/flash.h | 5 ++++-
- 1 file changed, 4 insertions(+), 1 deletion(-)
-
---- a/include/linux/spi/flash.h
-+++ b/include/linux/spi/flash.h
-@@ -2,7 +2,7 @@
- #define LINUX_SPI_FLASH_H
-
- struct mtd_partition;
--
-+struct mtd_part_parser_data;
- /**
- * struct flash_platform_data: board-specific flash data
- * @name: optional flash device name (eg, as used with mtdparts=)
-@@ -10,6 +10,8 @@ struct mtd_partition;
- * @nr_parts: number of mtd_partitions for static partitoning
- * @type: optional flash device type (e.g. m25p80 vs m25p64), for use
- * with chips that can't be queried for JEDEC or other IDs
-+ * @part_probe_types: optional list of MTD parser names to use for
-+ * partitioning
- *
- * Board init code (in arch/.../mach-xxx/board-yyy.c files) can
- * provide information about SPI flash parts (such as DataFlash) to
-@@ -25,6 +27,7 @@ struct flash_platform_data {
-
- char *type;
-
-+ const char **part_probe_types;
- /* we'll likely add more ... use JEDEC IDs, etc */
- };
-
+++ /dev/null
-From c7c3c338cb25d7f55ddb3f6bfbf3572758ca3896 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Thu, 10 Nov 2011 16:53:08 +0100
-Subject: [PATCH 50/79] MTD: DEVICES: m25p80: use parsers if provided in flash
- platform data
-
-Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
----
- drivers/mtd/devices/m25p80.c | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/drivers/mtd/devices/m25p80.c
-+++ b/drivers/mtd/devices/m25p80.c
-@@ -988,7 +988,8 @@ static int m25p_probe(struct spi_device
- /* partitions should match sector boundaries; and it may be good to
- * use readonly partitions for writeprotected sectors (BP2..BP0).
- */
-- return mtd_device_parse_register(&flash->mtd, NULL, &ppdata,
-+ return mtd_device_parse_register(&flash->mtd,
-+ data ? data->part_probe_types : NULL, &ppdata,
- data ? data->parts : NULL,
- data ? data->nr_parts : 0);
- }
+++ /dev/null
-From 5fb4e8d7287ac8fcb33aae8b1e9e22c5a3c392bd Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Thu, 10 Nov 2011 17:33:40 +0100
-Subject: [PATCH 51/79] MTD: DEVICES: m25p80: add support for limiting reads
-
-Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
----
- drivers/mtd/devices/m25p80.c | 29 +++++++++++++++++++++++++++--
- include/linux/spi/flash.h | 4 ++++
- 2 files changed, 31 insertions(+), 2 deletions(-)
-
---- a/drivers/mtd/devices/m25p80.c
-+++ b/drivers/mtd/devices/m25p80.c
-@@ -93,6 +93,7 @@ struct m25p {
- u8 erase_opcode;
- u8 *command;
- bool fast_read;
-+ int max_transfer_len;
- };
-
- static inline struct m25p *mtd_to_m25p(struct mtd_info *mtd)
-@@ -337,10 +338,9 @@ static int m25p80_erase(struct mtd_info
- * Read an address range from the flash chip. The address range
- * may be any size provided it is within the physical boundaries.
- */
--static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
-+static int __m25p80_read(struct m25p *flash, loff_t from, size_t len,
- size_t *retlen, u_char *buf)
- {
-- struct m25p *flash = mtd_to_m25p(mtd);
- struct spi_transfer t[2];
- struct spi_message m;
- uint8_t opcode;
-@@ -392,6 +392,28 @@ static int m25p80_read(struct mtd_info *
- return 0;
- }
-
-+static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
-+ size_t *retlen, u_char *buf)
-+{
-+ struct m25p *flash = mtd_to_m25p(mtd);
-+ size_t off;
-+ size_t read_len = flash->max_transfer_len;
-+ size_t part_len;
-+ int ret = 0;
-+
-+ if (!read_len)
-+ return __m25p80_read(flash, from, len, retlen, buf);
-+
-+ *retlen = 0;
-+
-+ for (off = 0; off < len && !ret; off += read_len) {
-+ ret = __m25p80_read(flash, from + off, min(len - off, read_len),
-+ &part_len, buf + off);
-+ *retlen += part_len;
-+ }
-+
-+ return ret;
-+}
- /*
- * Write an address range to the flash chip. Data must be written in
- * FLASH_PAGESIZE chunks. The address range may be any size provided
-@@ -889,6 +911,9 @@ static int m25p_probe(struct spi_device
- return -ENOMEM;
- }
-
-+ if (data)
-+ flash->max_transfer_len = data->max_transfer_len;
-+
- flash->spi = spi;
- mutex_init(&flash->lock);
- dev_set_drvdata(&spi->dev, flash);
---- a/include/linux/spi/flash.h
-+++ b/include/linux/spi/flash.h
-@@ -13,6 +13,8 @@ struct mtd_part_parser_data;
- * @part_probe_types: optional list of MTD parser names to use for
- * partitioning
- *
-+ * @max_transfer_len: option maximum read/write length limitation for
-+ * SPI controllers not able to transfer any length commands.
- * Board init code (in arch/.../mach-xxx/board-yyy.c files) can
- * provide information about SPI flash parts (such as DataFlash) to
- * help set up the device and its appropriate default partitioning.
-@@ -28,6 +30,8 @@ struct flash_platform_data {
- char *type;
-
- const char **part_probe_types;
-+
-+ unsigned int max_transfer_len;
- /* we'll likely add more ... use JEDEC IDs, etc */
- };
-
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -12,6 +12,8 @@
- #include <linux/string.h>
- #include <linux/platform_device.h>
- #include <linux/ssb/ssb.h>
-+#include <linux/gpio_keys.h>
-+#include <linux/input.h>
- #include <asm/addrspace.h>
- #include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
-@@ -32,6 +34,9 @@
-
- #define PFX "board_bcm963xx: "
-
-+#define BCM963XX_KEYS_POLL_INTERVAL 20
-+#define BCM963XX_KEYS_DEBOUNCE_INTERVAL (BCM963XX_KEYS_POLL_INTERVAL * 3)
-+
- static struct board_info board;
-
- /*
-@@ -343,6 +348,16 @@ static struct board_info __initdata boar
- .active_low = 1,
- },
- },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 33,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
- };
-
- static struct board_info __initdata board_96348gw = {
-@@ -401,6 +416,16 @@ static struct board_info __initdata boar
- .active_low = 1,
- },
- },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 36,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
- };
-
- static struct board_info __initdata board_FAST2404 = {
-@@ -825,11 +850,23 @@ static struct platform_device bcm63xx_gp
- .dev.platform_data = &bcm63xx_led_data,
- };
-
-+static struct gpio_keys_platform_data bcm63xx_gpio_keys_data = {
-+ .poll_interval = BCM963XX_KEYS_POLL_INTERVAL,
-+};
-+
-+static struct platform_device bcm63xx_gpio_keys_device = {
-+ .name = "gpio-keys-polled",
-+ .id = 0,
-+ .dev.platform_data = &bcm63xx_gpio_keys_data,
-+};
-+
- /*
- * third stage init callback, register all board devices.
- */
- int __init board_register_devices(void)
- {
-+ int button_count = 0;
-+
- if (board.has_uart0)
- bcm63xx_uart_register(0);
-
-@@ -881,5 +918,16 @@ int __init board_register_devices(void)
-
- platform_device_register(&bcm63xx_gpio_leds);
-
-+ /* count number of BUTTONs defined by this device */
-+ while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc)
-+ button_count++;
-+
-+ if (button_count) {
-+ bcm63xx_gpio_keys_data.nbuttons = button_count;
-+ bcm63xx_gpio_keys_data.buttons = board.buttons;
-+
-+ platform_device_register(&bcm63xx_gpio_keys_device);
-+ }
-+
- return 0;
- }
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -3,6 +3,7 @@
-
- #include <linux/types.h>
- #include <linux/gpio.h>
-+#include <linux/gpio_keys.h>
- #include <linux/leds.h>
- #include <bcm63xx_dev_enet.h>
- #include <bcm63xx_dev_usb_usbd.h>
-@@ -45,6 +46,9 @@ struct board_info {
-
- /* GPIO LEDs */
- struct gpio_led leds[5];
-+
-+ /* Buttons */
-+ struct gpio_keys_button buttons[4];
- };
-
- #endif /* ! BOARD_BCM963XX_H_ */
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -866,6 +866,7 @@ static struct platform_device bcm63xx_gp
- int __init board_register_devices(void)
- {
- int button_count = 0;
-+ int led_count = 0;
-
- if (board.has_uart0)
- bcm63xx_uart_register(0);
-@@ -913,10 +914,16 @@ int __init board_register_devices(void)
-
- bcm63xx_flash_register();
-
-- bcm63xx_led_data.num_leds = ARRAY_SIZE(board.leds);
-- bcm63xx_led_data.leds = board.leds;
-+ /* count number of LEDs defined by this device */
-+ while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name)
-+ led_count++;
-+
-+ if (led_count) {
-+ bcm63xx_led_data.num_leds = led_count;
-+ bcm63xx_led_data.leds = board.leds;
-
-- platform_device_register(&bcm63xx_gpio_leds);
-+ platform_device_register(&bcm63xx_gpio_leds);
-+ }
-
- /* count number of BUTTONs defined by this device */
- while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc)
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -45,7 +45,7 @@ struct board_info {
- struct bcm63xx_dsp_platform_data dsp;
-
- /* GPIO LEDs */
-- struct gpio_led leds[5];
-+ struct gpio_led leds[14];
-
- /* Buttons */
- struct gpio_keys_button buttons[4];
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -912,6 +912,9 @@ int __init board_register_devices(void)
-
- bcm63xx_spi_register();
-
-+ if (board.num_devs)
-+ platform_add_devices(board.devs, board.num_devs);
-+
- bcm63xx_flash_register();
-
- /* count number of LEDs defined by this device */
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -49,6 +49,10 @@ struct board_info {
-
- /* Buttons */
- struct gpio_keys_button buttons[4];
-+
-+ /* Additional platform devices */
-+ struct platform_device **devs;
-+ unsigned int num_devs;
- };
-
- #endif /* ! BOARD_BCM963XX_H_ */
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -14,6 +14,7 @@
- #include <linux/ssb/ssb.h>
- #include <linux/gpio_keys.h>
- #include <linux/input.h>
-+#include <linux/spi/spi.h>
- #include <asm/addrspace.h>
- #include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
-@@ -915,6 +916,9 @@ int __init board_register_devices(void)
- if (board.num_devs)
- platform_add_devices(board.devs, board.num_devs);
-
-+ if (board.num_spis)
-+ spi_register_board_info(board.spis, board.num_spis);
-+
- bcm63xx_flash_register();
-
- /* count number of LEDs defined by this device */
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -53,6 +53,10 @@ struct board_info {
- /* Additional platform devices */
- struct platform_device **devs;
- unsigned int num_devs;
-+
-+ /* Additional platform devices */
-+ struct spi_board_info *spis;
-+ unsigned int num_spis;
- };
-
- #endif /* ! BOARD_BCM963XX_H_ */
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -33,11 +33,16 @@
- #include <bcm63xx_dev_usb_usbd.h>
- #include <board_bcm963xx.h>
-
-+#include <uapi/linux/bcm963xx_tag.h>
-+
- #define PFX "board_bcm963xx: "
-
- #define BCM963XX_KEYS_POLL_INTERVAL 20
- #define BCM963XX_KEYS_DEBOUNCE_INTERVAL (BCM963XX_KEYS_POLL_INTERVAL * 3)
-
-+#define CFE_OFFSET_64K 0x10000
-+#define CFE_OFFSET_128K 0x20000
-+
- static struct board_info board;
-
- /*
-@@ -742,6 +747,30 @@ const char *board_get_name(void)
- return board.name;
- }
-
-+static void __init boardid_fixup(u8 *boot_addr)
-+{
-+ struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K);
-+ char *board_name = (char *)bcm63xx_nvram_get_name();
-+
-+ /* check if bcm_tag is at 64k offset */
-+ if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) {
-+ /* else try 128k */
-+ tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_128K);
-+ if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) {
-+ /* No tag found */
-+ printk(KERN_DEBUG "No bcm_tag found!\n");
-+ return;
-+ }
-+ }
-+ /* check if we should override the boardid */
-+ if (tag->information1[0] != '+')
-+ return;
-+
-+ strncpy(board_name, &tag->information1[1], BOARDID_LEN);
-+
-+ printk(KERN_INFO "Overriding boardid with '%s'\n", board_name);
-+}
-+
- /*
- * early init callback, read nvram data from flash and checksum it
- */
-@@ -775,6 +804,11 @@ void __init board_prom_init(void)
-
- bcm63xx_nvram_init(boot_addr + BCM963XX_NVRAM_OFFSET);
-
-+ if (strcmp(cfe_version, "unknown") != 0) {
-+ /* cfe present */
-+ boardid_fixup(boot_addr);
-+ }
-+
- board_name = bcm63xx_nvram_get_name();
- /* find board by name */
- for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) {
+++ /dev/null
-From c110865541e2d3782c412af9d48c016de5a64d9c Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Tue, 14 Jun 2011 21:14:39 +0200
-Subject: [PATCH 42/79] MIPS: BCM63XX: allow second UART on BCM6328
-
-Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
----
- arch/mips/bcm63xx/dev-uart.c | 3 ++-
- 1 file changed, 2 insertions(+), 1 deletion(-)
-
---- a/arch/mips/bcm63xx/dev-uart.c
-+++ b/arch/mips/bcm63xx/dev-uart.c
-@@ -54,7 +54,8 @@ int __init bcm63xx_uart_register(unsigne
- if (id >= ARRAY_SIZE(bcm63xx_uart_devices))
- return -ENODEV;
-
-- if (id == 1 && (!BCMCPU_IS_6358() && !BCMCPU_IS_6368()))
-+ if (id == 1 && !BCMCPU_IS_6328() && !BCMCPU_IS_6358() &&
-+ !BCMCPU_IS_6368())
- return -ENODEV;
-
- if (id == 0) {
+++ /dev/null
-From 5aeb6273a610f8aab090b3499827177eb41311ba Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Sat, 12 Nov 2011 12:19:09 +0100
-Subject: [PATCH 53/79] MIPS: BCM63XX: expose the HS SPI clock
-
-Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
----
- arch/mips/bcm63xx/clk.c | 22 ++++++++++++++++++++++
- 1 file changed, 22 insertions(+)
-
---- a/arch/mips/bcm63xx/clk.c
-+++ b/arch/mips/bcm63xx/clk.c
-@@ -236,6 +236,26 @@ static struct clk clk_spi = {
- };
-
- /*
-+ * SPI clock
-+ */
-+static void hsspi_set(struct clk *clk, int enable)
-+{
-+ u32 mask;
-+
-+ if (BCMCPU_IS_6328())
-+ mask = CKCTL_6328_HSSPI_EN;
-+ else
-+ return;
-+
-+ bcm_hwclock_set(mask, enable);
-+}
-+
-+static struct clk clk_hsspi = {
-+ .set = hsspi_set,
-+};
-+
-+
-+/*
- * XTM clock
- */
- static void xtm_set(struct clk *clk, int enable)
-@@ -344,6 +364,8 @@ struct clk *clk_get(struct device *dev,
- return &clk_usbd;
- if (!strcmp(id, "spi"))
- return &clk_spi;
-+ if (!strcmp(id, "hsspi"))
-+ return &clk_hsspi;
- if (!strcmp(id, "xtm"))
- return &clk_xtm;
- if (!strcmp(id, "periph"))
+++ /dev/null
-From 70f970222bc1096689ae1bffeb9ed09a7c4bed07 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Sat, 12 Nov 2011 12:19:55 +0100
-Subject: [PATCH 28/60] MIPS: BCM63XX: add HSSPI register definitions
-
-Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
----
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 18 ++++++++
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 47 +++++++++++++++++++++
- 2 files changed, 65 insertions(+), 0 deletions(-)
-
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-@@ -131,6 +131,7 @@ enum bcm63xx_regs_set {
- RSET_UART1,
- RSET_GPIO,
- RSET_SPI,
-+ RSET_HSSPI,
- RSET_UDC0,
- RSET_OHCI0,
- RSET_OHCI_PRIV,
-@@ -176,6 +177,7 @@ enum bcm63xx_regs_set {
- #define RSET_ENETDMA_SIZE 2048
- #define RSET_ENETSW_SIZE 65536
- #define RSET_UART_SIZE 24
-+#define RSET_HSSPI_SIZE 1536
- #define RSET_UDC_SIZE 256
- #define RSET_OHCI_SIZE 256
- #define RSET_EHCI_SIZE 256
-@@ -201,6 +203,7 @@ enum bcm63xx_regs_set {
- #define BCM_6328_UART1_BASE (0xb0000120)
- #define BCM_6328_GPIO_BASE (0xb0000080)
- #define BCM_6328_SPI_BASE (0xdeadbeef)
-+#define BCM_6328_HSSPI_BASE (0xb0001000)
- #define BCM_6328_UDC0_BASE (0xdeadbeef)
- #define BCM_6328_USBDMA_BASE (0xb000c000)
- #define BCM_6328_OHCI0_BASE (0xb0002600)
-@@ -247,6 +250,7 @@ enum bcm63xx_regs_set {
- #define BCM_6338_UART1_BASE (0xdeadbeef)
- #define BCM_6338_GPIO_BASE (0xfffe0400)
- #define BCM_6338_SPI_BASE (0xfffe0c00)
-+#define BCM_6338_HSSPI_BASE (0xdeadbeef)
- #define BCM_6338_UDC0_BASE (0xdeadbeef)
- #define BCM_6338_USBDMA_BASE (0xfffe2400)
- #define BCM_6338_OHCI0_BASE (0xdeadbeef)
-@@ -294,6 +298,7 @@ enum bcm63xx_regs_set {
- #define BCM_6345_UART1_BASE (0xdeadbeef)
- #define BCM_6345_GPIO_BASE (0xfffe0400)
- #define BCM_6345_SPI_BASE (0xdeadbeef)
-+#define BCM_6345_HSSPI_BASE (0xdeadbeef)
- #define BCM_6345_UDC0_BASE (0xdeadbeef)
- #define BCM_6345_USBDMA_BASE (0xfffe2800)
- #define BCM_6345_ENET0_BASE (0xfffe1800)
-@@ -340,6 +345,7 @@ enum bcm63xx_regs_set {
- #define BCM_6348_UART1_BASE (0xdeadbeef)
- #define BCM_6348_GPIO_BASE (0xfffe0400)
- #define BCM_6348_SPI_BASE (0xfffe0c00)
-+#define BCM_6348_HSSPI_BASE (0xdeadbeef)
- #define BCM_6348_UDC0_BASE (0xfffe1000)
- #define BCM_6348_USBDMA_BASE (0xdeadbeef)
- #define BCM_6348_OHCI0_BASE (0xfffe1b00)
-@@ -385,6 +391,7 @@ enum bcm63xx_regs_set {
- #define BCM_6358_UART1_BASE (0xfffe0120)
- #define BCM_6358_GPIO_BASE (0xfffe0080)
- #define BCM_6358_SPI_BASE (0xfffe0800)
-+#define BCM_6358_HSSPI_BASE (0xdeadbeef)
- #define BCM_6358_UDC0_BASE (0xfffe0800)
- #define BCM_6358_USBDMA_BASE (0xdeadbeef)
- #define BCM_6358_OHCI0_BASE (0xfffe1400)
-@@ -487,6 +494,7 @@ enum bcm63xx_regs_set {
- #define BCM_6368_UART1_BASE (0xb0000120)
- #define BCM_6368_GPIO_BASE (0xb0000080)
- #define BCM_6368_SPI_BASE (0xb0000800)
-+#define BCM_6368_HSSPI_BASE (0xdeadbeef)
- #define BCM_6368_UDC0_BASE (0xdeadbeef)
- #define BCM_6368_USBDMA_BASE (0xb0004800)
- #define BCM_6368_OHCI0_BASE (0xb0001600)
-@@ -538,6 +546,7 @@ extern const unsigned long *bcm63xx_regs
- __GEN_RSET_BASE(__cpu, UART1) \
- __GEN_RSET_BASE(__cpu, GPIO) \
- __GEN_RSET_BASE(__cpu, SPI) \
-+ __GEN_RSET_BASE(__cpu, HSSPI) \
- __GEN_RSET_BASE(__cpu, UDC0) \
- __GEN_RSET_BASE(__cpu, OHCI0) \
- __GEN_RSET_BASE(__cpu, OHCI_PRIV) \
-@@ -581,6 +590,7 @@ extern const unsigned long *bcm63xx_regs
- [RSET_UART1] = BCM_## __cpu ##_UART1_BASE, \
- [RSET_GPIO] = BCM_## __cpu ##_GPIO_BASE, \
- [RSET_SPI] = BCM_## __cpu ##_SPI_BASE, \
-+ [RSET_HSSPI] = BCM_## __cpu ##_HSSPI_BASE, \
- [RSET_UDC0] = BCM_## __cpu ##_UDC0_BASE, \
- [RSET_OHCI0] = BCM_## __cpu ##_OHCI0_BASE, \
- [RSET_OHCI_PRIV] = BCM_## __cpu ##_OHCI_PRIV_BASE, \
-@@ -658,6 +668,7 @@ enum bcm63xx_irq {
- IRQ_ENET0,
- IRQ_ENET1,
- IRQ_ENET_PHY,
-+ IRQ_HSSPI,
- IRQ_OHCI0,
- IRQ_EHCI0,
- IRQ_USBD,
-@@ -700,6 +711,7 @@ enum bcm63xx_irq {
- #define BCM_6328_ENET0_IRQ 0
- #define BCM_6328_ENET1_IRQ 0
- #define BCM_6328_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 12)
-+#define BCM_6328_HSSPI_IRQ (IRQ_INTERNAL_BASE + 29)
- #define BCM_6328_OHCI0_IRQ (BCM_6328_HIGH_IRQ_BASE + 9)
- #define BCM_6328_EHCI0_IRQ (BCM_6328_HIGH_IRQ_BASE + 10)
- #define BCM_6328_USBD_IRQ (IRQ_INTERNAL_BASE + 4)
-@@ -745,6 +757,7 @@ enum bcm63xx_irq {
- #define BCM_6338_ENET0_IRQ (IRQ_INTERNAL_BASE + 8)
- #define BCM_6338_ENET1_IRQ 0
- #define BCM_6338_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9)
-+#define BCM_6338_HSSPI_IRQ 0
- #define BCM_6338_OHCI0_IRQ 0
- #define BCM_6338_EHCI0_IRQ 0
- #define BCM_6338_USBD_IRQ 0
-@@ -783,6 +796,7 @@ enum bcm63xx_irq {
- #define BCM_6345_ENET0_IRQ (IRQ_INTERNAL_BASE + 8)
- #define BCM_6345_ENET1_IRQ 0
- #define BCM_6345_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 12)
-+#define BCM_6345_HSSPI_IRQ 0
- #define BCM_6345_OHCI0_IRQ 0
- #define BCM_6345_EHCI0_IRQ 0
- #define BCM_6345_USBD_IRQ 0
-@@ -821,6 +835,7 @@ enum bcm63xx_irq {
- #define BCM_6348_ENET0_IRQ (IRQ_INTERNAL_BASE + 8)
- #define BCM_6348_ENET1_IRQ (IRQ_INTERNAL_BASE + 7)
- #define BCM_6348_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9)
-+#define BCM_6348_HSSPI_IRQ 0
- #define BCM_6348_OHCI0_IRQ (IRQ_INTERNAL_BASE + 12)
- #define BCM_6348_EHCI0_IRQ 0
- #define BCM_6348_USBD_IRQ 0
-@@ -859,6 +874,7 @@ enum bcm63xx_irq {
- #define BCM_6358_ENET0_IRQ (IRQ_INTERNAL_BASE + 8)
- #define BCM_6358_ENET1_IRQ (IRQ_INTERNAL_BASE + 6)
- #define BCM_6358_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9)
-+#define BCM_6358_HSSPI_IRQ 0
- #define BCM_6358_OHCI0_IRQ (IRQ_INTERNAL_BASE + 5)
- #define BCM_6358_EHCI0_IRQ (IRQ_INTERNAL_BASE + 10)
- #define BCM_6358_USBD_IRQ 0
-@@ -971,6 +987,7 @@ enum bcm63xx_irq {
- #define BCM_6368_ENET0_IRQ 0
- #define BCM_6368_ENET1_IRQ 0
- #define BCM_6368_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 15)
-+#define BCM_6368_HSSPI_IRQ 0
- #define BCM_6368_OHCI0_IRQ (IRQ_INTERNAL_BASE + 5)
- #define BCM_6368_EHCI0_IRQ (IRQ_INTERNAL_BASE + 7)
- #define BCM_6368_USBD_IRQ (IRQ_INTERNAL_BASE + 8)
-@@ -1018,6 +1035,7 @@ extern const int *bcm63xx_irqs;
- [IRQ_ENET0] = BCM_## __cpu ##_ENET0_IRQ, \
- [IRQ_ENET1] = BCM_## __cpu ##_ENET1_IRQ, \
- [IRQ_ENET_PHY] = BCM_## __cpu ##_ENET_PHY_IRQ, \
-+ [IRQ_HSSPI] = BCM_## __cpu ##_HSSPI_IRQ, \
- [IRQ_OHCI0] = BCM_## __cpu ##_OHCI0_IRQ, \
- [IRQ_EHCI0] = BCM_## __cpu ##_EHCI0_IRQ, \
- [IRQ_USBD] = BCM_## __cpu ##_USBD_IRQ, \
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -1434,4 +1434,51 @@
-
- #define PCIE_DEVICE_OFFSET 0x8000
-
-+/*************************************************************************
-+ * _REG relative to RSET_HSSPI
-+ *************************************************************************/
-+
-+#define HSSPI_GLOBAL_CTRL_REG 0x0
-+#define GLOBAL_CTRL_CLK_POLARITY (1 << 17)
-+#define GLOBAL_CTRL_CLK_GATE_SSOFF (1 << 16)
-+
-+#define HSSPI_GLOBAL_EXT_TRIGGER_REG 0x4
-+
-+#define HSSPI_INT_STATUS_REG 0x8
-+#define HSSPI_INT_STATUS_MASKED_REG 0xc
-+#define HSSPI_INT_MASK_REG 0x10
-+
-+#define HSSPI_PING0_CMD_DONE (1 << 0)
-+
-+#define HSSPI_INT_CLEAR_ALL 0xff001f1f
-+
-+#define HSSPI_PINGPONG_COMMAND_REG(x) (0x80 + (x) * 0x40)
-+#define PINGPONG_CMD_COMMAND_MASK 0xf
-+#define PINGPONG_COMMAND_NOOP 0
-+#define PINGPONG_COMMAND_START_NOW 1
-+#define PINGPONG_COMMAND_START_TRIGGER 2
-+#define PINGPONG_COMMAND_HALT 3
-+#define PINGPONG_COMMAND_FLUSH 4
-+#define PINGPONG_CMD_PROFILE_SHIFT 8
-+#define PINGPONG_CMD_SS_SHIFT 12
-+
-+#define HSSPI_PINGPONG_STATUS_REG(x) (0x84 + (x) * 0x40)
-+
-+#define HSSPI_PROFILE_CLK_CTRL_REG(x) (0x100 + (x) * 0x20)
-+#define CLK_CTRL_ACCUM_RST_ON_LOOP (1 << 15)
-+
-+#define HSSPI_PROFILE_SIGNAL_CTRL_REG(x) (0x104 + (x) * 0x20)
-+#define SIGNAL_CTRL_LATCH_RISING (1 << 12)
-+#define SIGNAL_CTRL_LAUNCH_RISING (1 << 13)
-+#define SIGNAL_CTRL_ASYNC_INPUT_PATH (1 << 16)
-+
-+#define HSSPI_PROFILE_MODE_CTRL_REG(x) (0x108 + (x) * 0x20)
-+#define MODE_CTRL_MULTIDATA_RD_STRT_SHIFT 8
-+#define MODE_CTRL_MULTIDATA_WR_STRT_SHIFT 12
-+#define MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT 16
-+#define MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT 18
-+#define MODE_CTRL_PREPENDBYTE_CNT_SHIFT 24
-+
-+#define HSSPI_FIFO_REG(x) (0x200 + (x) * 0x200)
-+
- #endif /* BCM63XX_REGS_H_ */
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -112,28 +112,28 @@ static struct board_info __initdata boar
-
- .leds = {
- {
-- .name = "adsl",
-+ .name = "96338GW:green:adsl",
- .gpio = 3,
- .active_low = 1,
- },
- {
-- .name = "ses",
-+ .name = "96338GW:green:ses",
- .gpio = 5,
- .active_low = 1,
- },
- {
-- .name = "ppp-fail",
-+ .name = "96338GW:green:ppp-fail",
- .gpio = 4,
- .active_low = 1,
- },
- {
-- .name = "power",
-+ .name = "96338GW:green:power",
- .gpio = 0,
- .active_low = 1,
- .default_trigger = "default-on",
- },
- {
-- .name = "stop",
-+ .name = "96338GW:green:stop",
- .gpio = 1,
- .active_low = 1,
- }
-@@ -153,28 +153,28 @@ static struct board_info __initdata boar
-
- .leds = {
- {
-- .name = "adsl",
-+ .name = "96338W:green:adsl",
- .gpio = 3,
- .active_low = 1,
- },
- {
-- .name = "ses",
-+ .name = "96338W:green:ses",
- .gpio = 5,
- .active_low = 1,
- },
- {
-- .name = "ppp-fail",
-+ .name = "96338W:green:ppp-fail",
- .gpio = 4,
- .active_low = 1,
- },
- {
-- .name = "power",
-+ .name = "96338W:green:power",
- .gpio = 0,
- .active_low = 1,
- .default_trigger = "default-on",
- },
- {
-- .name = "stop",
-+ .name = "96338W:green:stop",
- .gpio = 1,
- .active_low = 1,
- },
-@@ -213,29 +213,29 @@ static struct board_info __initdata boar
-
- .leds = {
- {
-- .name = "adsl-fail",
-+ .name = "96348R:green:adsl-fail",
- .gpio = 2,
- .active_low = 1,
- },
- {
-- .name = "ppp",
-+ .name = "96348R:green:ppp",
- .gpio = 3,
- .active_low = 1,
- },
- {
-- .name = "ppp-fail",
-+ .name = "96348R:green:ppp-fail",
- .gpio = 4,
- .active_low = 1,
- },
- {
-- .name = "power",
-+ .name = "96348R:green:power",
- .gpio = 0,
- .active_low = 1,
- .default_trigger = "default-on",
-
- },
- {
-- .name = "stop",
-+ .name = "96348R:green:stop",
- .gpio = 1,
- .active_low = 1,
- },
-@@ -274,28 +274,28 @@ static struct board_info __initdata boar
-
- .leds = {
- {
-- .name = "adsl-fail",
-+ .name = "96348GW-10:green:adsl-fail",
- .gpio = 2,
- .active_low = 1,
- },
- {
-- .name = "ppp",
-+ .name = "96348GW-10:green:ppp",
- .gpio = 3,
- .active_low = 1,
- },
- {
-- .name = "ppp-fail",
-+ .name = "96348GW-10:green:ppp-fail",
- .gpio = 4,
- .active_low = 1,
- },
- {
-- .name = "power",
-+ .name = "96348GW-10:green:power",
- .gpio = 0,
- .active_low = 1,
- .default_trigger = "default-on",
- },
- {
-- .name = "stop",
-+ .name = "96348GW-10:green:stop",
- .gpio = 1,
- .active_low = 1,
- },
-@@ -328,28 +328,28 @@ static struct board_info __initdata boar
-
- .leds = {
- {
-- .name = "adsl-fail",
-+ .name = "96348GW-11:green:adsl-fail",
- .gpio = 2,
- .active_low = 1,
- },
- {
-- .name = "ppp",
-+ .name = "96348GW-11:green:ppp",
- .gpio = 3,
- .active_low = 1,
- },
- {
-- .name = "ppp-fail",
-+ .name = "96348GW-11:green:ppp-fail",
- .gpio = 4,
- .active_low = 1,
- },
- {
-- .name = "power",
-+ .name = "96348GW-11:green:power",
- .gpio = 0,
- .active_low = 1,
- .default_trigger = "default-on",
- },
- {
-- .name = "stop",
-+ .name = "96348GW-11:green:stop",
- .gpio = 1,
- .active_low = 1,
- },
-@@ -396,28 +396,28 @@ static struct board_info __initdata boar
-
- .leds = {
- {
-- .name = "adsl-fail",
-+ .name = "96348GW:green:adsl-fail",
- .gpio = 2,
- .active_low = 1,
- },
- {
-- .name = "ppp",
-+ .name = "96348GW:green:ppp",
- .gpio = 3,
- .active_low = 1,
- },
- {
-- .name = "ppp-fail",
-+ .name = "96348GW:green:ppp-fail",
- .gpio = 4,
- .active_low = 1,
- },
- {
-- .name = "power",
-+ .name = "96348GW:green:power",
- .gpio = 0,
- .active_low = 1,
- .default_trigger = "default-on",
- },
- {
-- .name = "stop",
-+ .name = "96348GW:green:stop",
- .gpio = 1,
- .active_low = 1,
- },
-@@ -549,27 +549,27 @@ static struct board_info __initdata boar
-
- .leds = {
- {
-- .name = "adsl-fail",
-+ .name = "96358VW:green:adsl-fail",
- .gpio = 15,
- .active_low = 1,
- },
- {
-- .name = "ppp",
-+ .name = "96358VW:green:ppp",
- .gpio = 22,
- .active_low = 1,
- },
- {
-- .name = "ppp-fail",
-+ .name = "96358VW:green:ppp-fail",
- .gpio = 23,
- .active_low = 1,
- },
- {
-- .name = "power",
-+ .name = "96358VW:green:power",
- .gpio = 4,
- .default_trigger = "default-on",
- },
- {
-- .name = "stop",
-+ .name = "96358VW:green:stop",
- .gpio = 5,
- },
- },
-@@ -601,22 +601,22 @@ static struct board_info __initdata boar
-
- .leds = {
- {
-- .name = "adsl",
-+ .name = "96358VW2:green:adsl",
- .gpio = 22,
- .active_low = 1,
- },
- {
-- .name = "ppp-fail",
-+ .name = "96358VW2:green:ppp-fail",
- .gpio = 23,
- },
- {
-- .name = "power",
-+ .name = "96358VW2:green:power",
- .gpio = 5,
- .active_low = 1,
- .default_trigger = "default-on",
- },
- {
-- .name = "stop",
-+ .name = "96358VW2:green:stop",
- .gpio = 4,
- .active_low = 1,
- },
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -798,6 +798,8 @@ void __init board_prom_init(void)
- if (!memcmp(cfe, "cfe-v", 5))
- snprintf(cfe_version, sizeof(cfe_version), "%u.%u.%u-%u.%u",
- cfe[5], cfe[6], cfe[7], cfe[8], cfe[9]);
-+ else if (!memcmp(cfe, "cfe-", 4))
-+ snprintf(cfe_version, 16, "%s", (char *) &cfe[4]);
- else
- strcpy(cfe_version, "unknown");
- printk(KERN_INFO PFX "CFE version: %s\n", cfe_version);
+++ /dev/null
-From 10ea7fd6b854c3ecf745d053beba10c7e00c33c9 Mon Sep 17 00:00:00 2001
-From: Kevin Cernekee <cernekee@gmail.com>
-Date: Sat, 9 Jul 2011 12:15:06 -0700
-Subject: [PATCH 01/13] MIPS: BCM63XX: Add SMP support to prom.c
-
-This involves two changes to the BSP code:
-
-1) register_smp_ops() for BMIPS SMP
-
-2) The CPU1 boot vector on some of the BCM63xx platforms conflicts with
-the special interrupt vector (IV). Move it to 0x8000_0380 at boot time,
-to resolve the conflict.
-
-Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
-[jogo@openwrt: move smp ops registration below #ifdef guard, don't enable
- smp for 6328/6358]
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/prom.c | 33 +++++++++++++++++++++++++++++++++
- 1 file changed, 33 insertions(+)
-
---- a/arch/mips/bcm63xx/prom.c
-+++ b/arch/mips/bcm63xx/prom.c
-@@ -8,7 +8,11 @@
-
- #include <linux/init.h>
- #include <linux/bootmem.h>
-+#include <linux/smp.h>
- #include <asm/bootinfo.h>
-+#include <asm/bmips.h>
-+#include <asm/smp-ops.h>
-+#include <asm/mipsregs.h>
- #include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
- #include <bcm63xx_io.h>
-@@ -52,6 +56,35 @@ void __init prom_init(void)
-
- /* do low level board init */
- board_prom_init();
-+
-+#if defined(CONFIG_CPU_BMIPS4350) && defined(CONFIG_SMP)
-+ /* set up SMP */
-+ register_smp_ops(&bmips_smp_ops);
-+
-+ /*
-+ * BCM6328 does not have its second CPU enabled, while BCM6358
-+ * needs special handling for its shared TLB, so disable SMP for now.
-+ */
-+ if (BCMCPU_IS_6328() || BCMCPU_IS_6358()) {
-+ bmips_smp_enabled = 0;
-+ return;
-+ }
-+
-+ /*
-+ * The bootloader has set up the CPU1 reset vector at 0xa000_0200.
-+ * This conflicts with the special interrupt vector (IV).
-+ * The bootloader has also set up CPU1 to respond to the wrong
-+ * IPI interrupt.
-+ * Here we will start up CPU1 in the background and ask it to
-+ * reconfigure itself then go back to sleep.
-+ */
-+ memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20);
-+ __sync();
-+ set_c0_cause(C_SW0);
-+ cpumask_set_cpu(1, &bmips_booted_mask);
-+
-+ /* FIXME: we really should have some sort of hazard barrier here */
-+#endif
- }
-
- void __init prom_free_prom_memory(void)
+++ /dev/null
-From 8e0bd819cc0f8815cad99feea98664172c0b1fe4 Mon Sep 17 00:00:00 2001
-From: Kevin Cernekee <cernekee@gmail.com>
-Date: Mon, 31 Oct 2011 11:52:10 -0700
-Subject: [PATCH 02/13] MIPS: BCM63XX: Handle SW IRQs 0-1
-
-MIPS software IRQs 0 and 1 are used for interprocessor signaling (IPI)
-on BMIPS SMP. Make the board support code aware of them.
-
-Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
-[jogo@openwrt.org: move sw irqs behind timer irq]
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/irq.c | 4 ++++
- 1 file changed, 4 insertions(+)
-
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -294,6 +294,10 @@ asmlinkage void plat_irq_dispatch(void)
-
- if (cause & CAUSEF_IP7)
- do_IRQ(7);
-+ if (cause & CAUSEF_IP0)
-+ do_IRQ(0);
-+ if (cause & CAUSEF_IP1)
-+ do_IRQ(1);
- if (cause & CAUSEF_IP2)
- dispatch_internal();
- if (!is_ext_irq_cascaded) {
+++ /dev/null
-From 1923ce1435a5e89f9550e8c95db37a3ef1f92665 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sun, 21 Apr 2013 14:44:00 +0200
-Subject: [PATCH 03/13] MIPS: BCM63XX: select SYS_HAS_CPU_BMIPS4350 for
- supported SoCs
-
-BCM6338, BCM6345 and BCM6348 have a BMIPS3300, everything following
-has a BMIPS4350.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/Kconfig | 1 +
- 1 file changed, 1 insertion(+)
-
---- a/arch/mips/Kconfig
-+++ b/arch/mips/Kconfig
-@@ -126,6 +126,7 @@ config BCM63XX
- select DMA_NONCOHERENT
- select IRQ_CPU
- select SYS_HAS_CPU_MIPS32_R1
-+ select SYS_HAS_CPU_BMIPS4350 if !BCM63XX_CPU_6338 && !BCM63XX_CPU_6345 && !BCM63XX_CPU_6348
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_HAS_EARLY_PRINTK
+++ /dev/null
-From bb2774da9598f3ea38099d3dcf753b585824a011 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Thu, 21 Mar 2013 17:05:15 +0100
-Subject: [PATCH 04/13] MIPS: BCM63XX: rename __dispatch_internal to
- __dispatch_internal_32
-
-Make it follow the same naming convention as the other functions.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/irq.c | 8 ++++----
- 1 file changed, 4 insertions(+), 4 deletions(-)
-
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -19,7 +19,7 @@
- #include <bcm63xx_io.h>
- #include <bcm63xx_irq.h>
-
--static void __dispatch_internal(void) __maybe_unused;
-+static void __dispatch_internal_32(void) __maybe_unused;
- static void __dispatch_internal_64(void) __maybe_unused;
- static void __internal_irq_mask_32(unsigned int irq) __maybe_unused;
- static void __internal_irq_mask_64(unsigned int irq) __maybe_unused;
-@@ -106,7 +106,7 @@ static void __internal_irq_unmask_64(uns
- #endif
-
- #if irq_bits == 32
--#define dispatch_internal __dispatch_internal
-+#define dispatch_internal __dispatch_internal_32
- #define internal_irq_mask __internal_irq_mask_32
- #define internal_irq_unmask __internal_irq_unmask_32
- #else
-@@ -207,7 +207,7 @@ static void bcm63xx_init_irq(void)
- }
-
- if (irq_bits == 32) {
-- dispatch_internal = __dispatch_internal;
-+ dispatch_internal = __dispatch_internal_32;
- internal_irq_mask = __internal_irq_mask_32;
- internal_irq_unmask = __internal_irq_unmask_32;
- } else {
-@@ -240,7 +240,7 @@ static inline void handle_internal(int i
- * will resume the loop where it ended the last time we left this
- * function.
- */
--static void __dispatch_internal(void)
-+static void __dispatch_internal_32(void)
- {
- u32 pending;
- static int i;
+++ /dev/null
-From 661e02b8e2b9a4b48a809bc82dfe8f7b20ca750f Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Thu, 18 Apr 2013 21:14:49 +0200
-Subject: [PATCH 05/13] MIPS: BCM63XX: replace irq dispatch code with a
- generic version
-
-The generic version uses a variable length of u32 registers of u32/u64.
-This allows easier support for longer registers without having to rewrite
-verything.
-
-This "generic" version is not slower than the old version in the best case
-(= i == next set bit), and twice as fast in the worst case in 64 bits.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/irq.c | 130 ++++++++++++++++++++---------------------------
- 1 file changed, 56 insertions(+), 74 deletions(-)
-
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -240,47 +240,65 @@ static inline void handle_internal(int i
- * will resume the loop where it ended the last time we left this
- * function.
- */
--static void __dispatch_internal_32(void)
--{
-- u32 pending;
-- static int i;
--
-- pending = bcm_readl(irq_stat_addr) & bcm_readl(irq_mask_addr);
--
-- if (!pending)
-- return ;
--
-- while (1) {
-- int to_call = i;
-
-- i = (i + 1) & 0x1f;
-- if (pending & (1 << to_call)) {
-- handle_internal(to_call);
-- break;
-- }
-- }
-+#define BUILD_IPIC_INTERNAL(width) \
-+void __dispatch_internal_##width(void) \
-+{ \
-+ u32 pending[width / 32]; \
-+ unsigned int src, tgt; \
-+ bool irqs_pending = false; \
-+ static int i; \
-+ \
-+ /* read registers in reverse order */ \
-+ for (src = 0, tgt = (width / 32); src < (width / 32); src++) { \
-+ u32 val; \
-+ \
-+ val = bcm_readl(irq_stat_addr + src * sizeof(u32)); \
-+ val &= bcm_readl(irq_mask_addr + src * sizeof(u32)); \
-+ pending[--tgt] = val; \
-+ \
-+ if (val) \
-+ irqs_pending = true; \
-+ } \
-+ \
-+ if (!irqs_pending) \
-+ return; \
-+ \
-+ while (1) { \
-+ int to_call = i; \
-+ \
-+ i = (i + 1) & (width - 1); \
-+ if (pending[to_call / 32] & (1 << (to_call & 0x1f))) { \
-+ handle_internal(to_call); \
-+ break; \
-+ } \
-+ } \
-+} \
-+ \
-+static void __internal_irq_mask_##width(unsigned int irq) \
-+{ \
-+ u32 val; \
-+ unsigned reg = (irq / 32) ^ (width/32 - 1); \
-+ unsigned bit = irq & 0x1f; \
-+ \
-+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \
-+ val &= ~(1 << bit); \
-+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \
-+} \
-+ \
-+static void __internal_irq_unmask_##width(unsigned int irq) \
-+{ \
-+ u32 val; \
-+ unsigned reg = (irq / 32) ^ (width/32 - 1); \
-+ unsigned bit = irq & 0x1f; \
-+ \
-+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \
-+ val |= (1 << bit); \
-+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \
- }
-
--static void __dispatch_internal_64(void)
--{
-- u64 pending;
-- static int i;
--
-- pending = bcm_readq(irq_stat_addr) & bcm_readq(irq_mask_addr);
--
-- if (!pending)
-- return ;
--
-- while (1) {
-- int to_call = i;
--
-- i = (i + 1) & 0x3f;
-- if (pending & (1ull << to_call)) {
-- handle_internal(to_call);
-- break;
-- }
-- }
--}
-+BUILD_IPIC_INTERNAL(32);
-+BUILD_IPIC_INTERNAL(64);
-
- asmlinkage void plat_irq_dispatch(void)
- {
-@@ -317,42 +335,6 @@ asmlinkage void plat_irq_dispatch(void)
- * internal IRQs operations: only mask/unmask on PERF irq mask
- * register.
- */
--static void __internal_irq_mask_32(unsigned int irq)
--{
-- u32 mask;
--
-- mask = bcm_readl(irq_mask_addr);
-- mask &= ~(1 << irq);
-- bcm_writel(mask, irq_mask_addr);
--}
--
--static void __internal_irq_mask_64(unsigned int irq)
--{
-- u64 mask;
--
-- mask = bcm_readq(irq_mask_addr);
-- mask &= ~(1ull << irq);
-- bcm_writeq(mask, irq_mask_addr);
--}
--
--static void __internal_irq_unmask_32(unsigned int irq)
--{
-- u32 mask;
--
-- mask = bcm_readl(irq_mask_addr);
-- mask |= (1 << irq);
-- bcm_writel(mask, irq_mask_addr);
--}
--
--static void __internal_irq_unmask_64(unsigned int irq)
--{
-- u64 mask;
--
-- mask = bcm_readq(irq_mask_addr);
-- mask |= (1ull << irq);
-- bcm_writeq(mask, irq_mask_addr);
--}
--
- static void bcm63xx_internal_irq_mask(struct irq_data *d)
- {
- internal_irq_mask(d->irq - IRQ_INTERNAL_BASE);
+++ /dev/null
-From 6ec70ebfccd31ae3668d99b5703e5c9ce38384b4 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Thu, 25 Apr 2013 00:24:06 +0200
-Subject: [PATCH 06/13] MIPS: BCM63XX: append cpu number to irq_{stat,mask}*
-
-For SMP affinity support we need to discrimnate between the registers
-for both CPUs.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/irq.c | 78 ++++++++++-----------
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 16 ++---
- 2 files changed, 47 insertions(+), 47 deletions(-)
-
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -28,8 +28,8 @@ static void __internal_irq_unmask_64(uns
-
- #ifndef BCMCPU_RUNTIME_DETECT
- #ifdef CONFIG_BCM63XX_CPU_6328
--#define irq_stat_reg PERF_IRQSTAT_6328_REG
--#define irq_mask_reg PERF_IRQMASK_6328_REG
-+#define irq_stat_reg0 PERF_IRQSTAT_6328_REG(0)
-+#define irq_mask_reg0 PERF_IRQMASK_6328_REG(0)
- #define irq_bits 64
- #define is_ext_irq_cascaded 1
- #define ext_irq_start (BCM_6328_EXT_IRQ0 - IRQ_INTERNAL_BASE)
-@@ -39,8 +39,8 @@ static void __internal_irq_unmask_64(uns
- #define ext_irq_cfg_reg2 0
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6338
--#define irq_stat_reg PERF_IRQSTAT_6338_REG
--#define irq_mask_reg PERF_IRQMASK_6338_REG
-+#define irq_stat_reg0 PERF_IRQSTAT_6338_REG
-+#define irq_mask_reg0 PERF_IRQMASK_6338_REG
- #define irq_bits 32
- #define is_ext_irq_cascaded 0
- #define ext_irq_start 0
-@@ -50,8 +50,8 @@ static void __internal_irq_unmask_64(uns
- #define ext_irq_cfg_reg2 0
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6345
--#define irq_stat_reg PERF_IRQSTAT_6345_REG
--#define irq_mask_reg PERF_IRQMASK_6345_REG
-+#define irq_stat_reg0 PERF_IRQSTAT_6345_REG
-+#define irq_mask_reg0 PERF_IRQMASK_6345_REG
- #define irq_bits 32
- #define is_ext_irq_cascaded 0
- #define ext_irq_start 0
-@@ -61,8 +61,8 @@ static void __internal_irq_unmask_64(uns
- #define ext_irq_cfg_reg2 0
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6348
--#define irq_stat_reg PERF_IRQSTAT_6348_REG
--#define irq_mask_reg PERF_IRQMASK_6348_REG
-+#define irq_stat_reg0 PERF_IRQSTAT_6348_REG
-+#define irq_mask_reg0 PERF_IRQMASK_6348_REG
- #define irq_bits 32
- #define is_ext_irq_cascaded 0
- #define ext_irq_start 0
-@@ -72,8 +72,8 @@ static void __internal_irq_unmask_64(uns
- #define ext_irq_cfg_reg2 0
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6358
--#define irq_stat_reg PERF_IRQSTAT_6358_REG
--#define irq_mask_reg PERF_IRQMASK_6358_REG
-+#define irq_stat_reg0 PERF_IRQSTAT_6358_REG(0)
-+#define irq_mask_reg0 PERF_IRQMASK_6358_REG(0)
- #define irq_bits 32
- #define is_ext_irq_cascaded 1
- #define ext_irq_start (BCM_6358_EXT_IRQ0 - IRQ_INTERNAL_BASE)
-@@ -83,8 +83,8 @@ static void __internal_irq_unmask_64(uns
- #define ext_irq_cfg_reg2 0
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6362
--#define irq_stat_reg PERF_IRQSTAT_6362_REG
--#define irq_mask_reg PERF_IRQMASK_6362_REG
-+#define irq_stat_reg0 PERF_IRQSTAT_6362_REG(0)
-+#define irq_mask_reg0 PERF_IRQMASK_6362_REG(0)
- #define irq_bits 64
- #define is_ext_irq_cascaded 1
- #define ext_irq_start (BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE)
-@@ -94,8 +94,8 @@ static void __internal_irq_unmask_64(uns
- #define ext_irq_cfg_reg2 0
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6368
--#define irq_stat_reg PERF_IRQSTAT_6368_REG
--#define irq_mask_reg PERF_IRQMASK_6368_REG
-+#define irq_stat_reg0 PERF_IRQSTAT_6368_REG(0)
-+#define irq_mask_reg0 PERF_IRQMASK_6368_REG(0)
- #define irq_bits 64
- #define is_ext_irq_cascaded 1
- #define ext_irq_start (BCM_6368_EXT_IRQ0 - IRQ_INTERNAL_BASE)
-@@ -115,15 +115,15 @@ static void __internal_irq_unmask_64(uns
- #define internal_irq_unmask __internal_irq_unmask_64
- #endif
-
--#define irq_stat_addr (bcm63xx_regset_address(RSET_PERF) + irq_stat_reg)
--#define irq_mask_addr (bcm63xx_regset_address(RSET_PERF) + irq_mask_reg)
-+#define irq_stat_addr0 (bcm63xx_regset_address(RSET_PERF) + irq_stat_reg0)
-+#define irq_mask_addr0 (bcm63xx_regset_address(RSET_PERF) + irq_mask_reg0)
-
- static inline void bcm63xx_init_irq(void)
- {
- }
- #else /* ! BCMCPU_RUNTIME_DETECT */
-
--static u32 irq_stat_addr, irq_mask_addr;
-+static u32 irq_stat_addr0, irq_mask_addr0;
- static void (*dispatch_internal)(void);
- static int is_ext_irq_cascaded;
- static unsigned int ext_irq_count;
-@@ -136,13 +136,13 @@ static void bcm63xx_init_irq(void)
- {
- int irq_bits;
-
-- irq_stat_addr = bcm63xx_regset_address(RSET_PERF);
-- irq_mask_addr = bcm63xx_regset_address(RSET_PERF);
-+ irq_stat_addr0 = bcm63xx_regset_address(RSET_PERF);
-+ irq_mask_addr0 = bcm63xx_regset_address(RSET_PERF);
-
- switch (bcm63xx_get_cpu_id()) {
- case BCM6328_CPU_ID:
-- irq_stat_addr += PERF_IRQSTAT_6328_REG;
-- irq_mask_addr += PERF_IRQMASK_6328_REG;
-+ irq_stat_addr0 += PERF_IRQSTAT_6328_REG(0);
-+ irq_mask_addr0 += PERF_IRQMASK_6328_REG(0);
- irq_bits = 64;
- ext_irq_count = 4;
- is_ext_irq_cascaded = 1;
-@@ -151,29 +151,29 @@ static void bcm63xx_init_irq(void)
- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6328;
- break;
- case BCM6338_CPU_ID:
-- irq_stat_addr += PERF_IRQSTAT_6338_REG;
-- irq_mask_addr += PERF_IRQMASK_6338_REG;
-+ irq_stat_addr0 += PERF_IRQSTAT_6338_REG;
-+ irq_mask_addr0 += PERF_IRQMASK_6338_REG;
- irq_bits = 32;
- ext_irq_count = 4;
- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6338;
- break;
- case BCM6345_CPU_ID:
-- irq_stat_addr += PERF_IRQSTAT_6345_REG;
-- irq_mask_addr += PERF_IRQMASK_6345_REG;
-+ irq_stat_addr0 += PERF_IRQSTAT_6345_REG;
-+ irq_mask_addr0 += PERF_IRQMASK_6345_REG;
- irq_bits = 32;
- ext_irq_count = 4;
- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6345;
- break;
- case BCM6348_CPU_ID:
-- irq_stat_addr += PERF_IRQSTAT_6348_REG;
-- irq_mask_addr += PERF_IRQMASK_6348_REG;
-+ irq_stat_addr0 += PERF_IRQSTAT_6348_REG;
-+ irq_mask_addr0 += PERF_IRQMASK_6348_REG;
- irq_bits = 32;
- ext_irq_count = 4;
- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6348;
- break;
- case BCM6358_CPU_ID:
-- irq_stat_addr += PERF_IRQSTAT_6358_REG;
-- irq_mask_addr += PERF_IRQMASK_6358_REG;
-+ irq_stat_addr0 += PERF_IRQSTAT_6358_REG(0);
-+ irq_mask_addr0 += PERF_IRQMASK_6358_REG(0);
- irq_bits = 32;
- ext_irq_count = 4;
- is_ext_irq_cascaded = 1;
-@@ -182,8 +182,8 @@ static void bcm63xx_init_irq(void)
- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6358;
- break;
- case BCM6362_CPU_ID:
-- irq_stat_addr += PERF_IRQSTAT_6362_REG;
-- irq_mask_addr += PERF_IRQMASK_6362_REG;
-+ irq_stat_addr0 += PERF_IRQSTAT_6362_REG(0);
-+ irq_mask_addr0 += PERF_IRQMASK_6362_REG(0);
- irq_bits = 64;
- ext_irq_count = 4;
- is_ext_irq_cascaded = 1;
-@@ -192,8 +192,8 @@ static void bcm63xx_init_irq(void)
- ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_6362;
- break;
- case BCM6368_CPU_ID:
-- irq_stat_addr += PERF_IRQSTAT_6368_REG;
-- irq_mask_addr += PERF_IRQMASK_6368_REG;
-+ irq_stat_addr0 += PERF_IRQSTAT_6368_REG(0);
-+ irq_mask_addr0 += PERF_IRQMASK_6368_REG(0);
- irq_bits = 64;
- ext_irq_count = 6;
- is_ext_irq_cascaded = 1;
-@@ -253,8 +253,8 @@ void __dispatch_internal_##width(void)
- for (src = 0, tgt = (width / 32); src < (width / 32); src++) { \
- u32 val; \
- \
-- val = bcm_readl(irq_stat_addr + src * sizeof(u32)); \
-- val &= bcm_readl(irq_mask_addr + src * sizeof(u32)); \
-+ val = bcm_readl(irq_stat_addr0 + src * sizeof(u32)); \
-+ val &= bcm_readl(irq_mask_addr0 + src * sizeof(u32)); \
- pending[--tgt] = val; \
- \
- if (val) \
-@@ -281,9 +281,9 @@ static void __internal_irq_mask_##width(
- unsigned reg = (irq / 32) ^ (width/32 - 1); \
- unsigned bit = irq & 0x1f; \
- \
-- val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \
-+ val = bcm_readl(irq_mask_addr0 + reg * sizeof(u32)); \
- val &= ~(1 << bit); \
-- bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \
-+ bcm_writel(val, irq_mask_addr0 + reg * sizeof(u32)); \
- } \
- \
- static void __internal_irq_unmask_##width(unsigned int irq) \
-@@ -292,9 +292,9 @@ static void __internal_irq_unmask_##widt
- unsigned reg = (irq / 32) ^ (width/32 - 1); \
- unsigned bit = irq & 0x1f; \
- \
-- val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \
-+ val = bcm_readl(irq_mask_addr0 + reg * sizeof(u32)); \
- val |= (1 << bit); \
-- bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \
-+ bcm_writel(val, irq_mask_addr0 + reg * sizeof(u32)); \
- }
-
- BUILD_IPIC_INTERNAL(32);
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -181,22 +181,22 @@
- #define SYS_PLL_SOFT_RESET 0x1
-
- /* Interrupt Mask register */
--#define PERF_IRQMASK_6328_REG 0x20
-+#define PERF_IRQMASK_6328_REG(x) (0x20 + (x) * 0x10)
- #define PERF_IRQMASK_6338_REG 0xc
- #define PERF_IRQMASK_6345_REG 0xc
- #define PERF_IRQMASK_6348_REG 0xc
--#define PERF_IRQMASK_6358_REG 0xc
--#define PERF_IRQMASK_6362_REG 0x20
--#define PERF_IRQMASK_6368_REG 0x20
-+#define PERF_IRQMASK_6358_REG(x) (0xc + (x) * 0x2c)
-+#define PERF_IRQMASK_6362_REG(x) (0x20 + (x) * 0x10)
-+#define PERF_IRQMASK_6368_REG(x) (0x20 + (x) * 0x10)
-
- /* Interrupt Status register */
--#define PERF_IRQSTAT_6328_REG 0x28
-+#define PERF_IRQSTAT_6328_REG(x) (0x28 + (x) * 0x10)
- #define PERF_IRQSTAT_6338_REG 0x10
- #define PERF_IRQSTAT_6345_REG 0x10
- #define PERF_IRQSTAT_6348_REG 0x10
--#define PERF_IRQSTAT_6358_REG 0x10
--#define PERF_IRQSTAT_6362_REG 0x28
--#define PERF_IRQSTAT_6368_REG 0x28
-+#define PERF_IRQSTAT_6358_REG(x) (0x10 + (x) * 0x2c)
-+#define PERF_IRQSTAT_6362_REG(x) (0x28 + (x) * 0x10)
-+#define PERF_IRQSTAT_6368_REG(x) (0x28 + (x) * 0x10)
-
- /* External Interrupt Configuration register */
- #define PERF_EXTIRQ_CFG_REG_6328 0x18
+++ /dev/null
-From b14de5c78d32f8f98535a99ea56bb924beb66810 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Thu, 25 Apr 2013 00:31:29 +0200
-Subject: [PATCH 07/13] MIPS: BCM63XX: populate irq_{stat,mask}_addr for
- second CPU
-
-Populate it for all platforms with a BMIPS4350.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/irq.c | 28 +++++++++++++++++++++++++++-
- 1 file changed, 27 insertions(+), 1 deletion(-)
-
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -30,6 +30,8 @@ static void __internal_irq_unmask_64(uns
- #ifdef CONFIG_BCM63XX_CPU_6328
- #define irq_stat_reg0 PERF_IRQSTAT_6328_REG(0)
- #define irq_mask_reg0 PERF_IRQMASK_6328_REG(0)
-+#define irq_stat_reg1 PERF_IRQSTAT_6328_REG(1)
-+#define irq_mask_reg1 PERF_IRQMASK_6328_REG(1)
- #define irq_bits 64
- #define is_ext_irq_cascaded 1
- #define ext_irq_start (BCM_6328_EXT_IRQ0 - IRQ_INTERNAL_BASE)
-@@ -41,6 +43,8 @@ static void __internal_irq_unmask_64(uns
- #ifdef CONFIG_BCM63XX_CPU_6338
- #define irq_stat_reg0 PERF_IRQSTAT_6338_REG
- #define irq_mask_reg0 PERF_IRQMASK_6338_REG
-+#define irq_stat_reg1 0
-+#define irq_mask_reg1 0
- #define irq_bits 32
- #define is_ext_irq_cascaded 0
- #define ext_irq_start 0
-@@ -52,6 +56,8 @@ static void __internal_irq_unmask_64(uns
- #ifdef CONFIG_BCM63XX_CPU_6345
- #define irq_stat_reg0 PERF_IRQSTAT_6345_REG
- #define irq_mask_reg0 PERF_IRQMASK_6345_REG
-+#define irq_stat_reg1 0
-+#define irq_mask_reg1 0
- #define irq_bits 32
- #define is_ext_irq_cascaded 0
- #define ext_irq_start 0
-@@ -63,6 +69,8 @@ static void __internal_irq_unmask_64(uns
- #ifdef CONFIG_BCM63XX_CPU_6348
- #define irq_stat_reg0 PERF_IRQSTAT_6348_REG
- #define irq_mask_reg0 PERF_IRQMASK_6348_REG
-+#define irq_stat_reg1 0
-+#define irq_mask_reg1 0
- #define irq_bits 32
- #define is_ext_irq_cascaded 0
- #define ext_irq_start 0
-@@ -74,6 +82,8 @@ static void __internal_irq_unmask_64(uns
- #ifdef CONFIG_BCM63XX_CPU_6358
- #define irq_stat_reg0 PERF_IRQSTAT_6358_REG(0)
- #define irq_mask_reg0 PERF_IRQMASK_6358_REG(0)
-+#define irq_stat_reg1 PERF_IRQSTAT_6358_REG(1)
-+#define irq_mask_reg1 PERF_IRQMASK_6358_REG(1)
- #define irq_bits 32
- #define is_ext_irq_cascaded 1
- #define ext_irq_start (BCM_6358_EXT_IRQ0 - IRQ_INTERNAL_BASE)
-@@ -85,6 +95,8 @@ static void __internal_irq_unmask_64(uns
- #ifdef CONFIG_BCM63XX_CPU_6362
- #define irq_stat_reg0 PERF_IRQSTAT_6362_REG(0)
- #define irq_mask_reg0 PERF_IRQMASK_6362_REG(0)
-+#define irq_stat_reg1 PERF_IRQSTAT_6362_REG(1)
-+#define irq_mask_reg1 PERF_IRQMASK_6362_REG(1)
- #define irq_bits 64
- #define is_ext_irq_cascaded 1
- #define ext_irq_start (BCM_6362_EXT_IRQ0 - IRQ_INTERNAL_BASE)
-@@ -96,6 +108,8 @@ static void __internal_irq_unmask_64(uns
- #ifdef CONFIG_BCM63XX_CPU_6368
- #define irq_stat_reg0 PERF_IRQSTAT_6368_REG(0)
- #define irq_mask_reg0 PERF_IRQMASK_6368_REG(0)
-+#define irq_stat_reg1 PERF_IRQSTAT_6368_REG(1)
-+#define irq_mask_reg1 PERF_IRQMASK_6368_REG(1)
- #define irq_bits 64
- #define is_ext_irq_cascaded 1
- #define ext_irq_start (BCM_6368_EXT_IRQ0 - IRQ_INTERNAL_BASE)
-@@ -117,13 +131,15 @@ static void __internal_irq_unmask_64(uns
-
- #define irq_stat_addr0 (bcm63xx_regset_address(RSET_PERF) + irq_stat_reg0)
- #define irq_mask_addr0 (bcm63xx_regset_address(RSET_PERF) + irq_mask_reg0)
-+#define irq_stat_addr1 (bcm63xx_regset_address(RSET_PERF) + irq_stat_reg1)
-+#define irq_mask_addr1 (bcm63xx_regset_address(RSET_PERF) + irq_mask_reg1)
-
- static inline void bcm63xx_init_irq(void)
- {
- }
- #else /* ! BCMCPU_RUNTIME_DETECT */
-
--static u32 irq_stat_addr0, irq_mask_addr0;
-+static u32 irq_stat_addr0, irq_mask_addr0, irq_stat_addr1, irq_mask_addr1;
- static void (*dispatch_internal)(void);
- static int is_ext_irq_cascaded;
- static unsigned int ext_irq_count;
-@@ -138,11 +154,15 @@ static void bcm63xx_init_irq(void)
-
- irq_stat_addr0 = bcm63xx_regset_address(RSET_PERF);
- irq_mask_addr0 = bcm63xx_regset_address(RSET_PERF);
-+ irq_stat_addr1 = bcm63xx_regset_address(RSET_PERF);
-+ irq_mask_addr1 = bcm63xx_regset_address(RSET_PERF);
-
- switch (bcm63xx_get_cpu_id()) {
- case BCM6328_CPU_ID:
- irq_stat_addr0 += PERF_IRQSTAT_6328_REG(0);
- irq_mask_addr0 += PERF_IRQMASK_6328_REG(0);
-+ irq_stat_addr1 += PERF_IRQSTAT_6328_REG(1);
-+ irq_stat_addr1 += PERF_IRQMASK_6328_REG(1);
- irq_bits = 64;
- ext_irq_count = 4;
- is_ext_irq_cascaded = 1;
-@@ -174,6 +194,8 @@ static void bcm63xx_init_irq(void)
- case BCM6358_CPU_ID:
- irq_stat_addr0 += PERF_IRQSTAT_6358_REG(0);
- irq_mask_addr0 += PERF_IRQMASK_6358_REG(0);
-+ irq_stat_addr1 += PERF_IRQSTAT_6358_REG(1);
-+ irq_mask_addr1 += PERF_IRQMASK_6358_REG(1);
- irq_bits = 32;
- ext_irq_count = 4;
- is_ext_irq_cascaded = 1;
-@@ -184,6 +206,8 @@ static void bcm63xx_init_irq(void)
- case BCM6362_CPU_ID:
- irq_stat_addr0 += PERF_IRQSTAT_6362_REG(0);
- irq_mask_addr0 += PERF_IRQMASK_6362_REG(0);
-+ irq_stat_addr1 += PERF_IRQSTAT_6362_REG(1);
-+ irq_mask_addr1 += PERF_IRQMASK_6362_REG(1);
- irq_bits = 64;
- ext_irq_count = 4;
- is_ext_irq_cascaded = 1;
-@@ -194,6 +218,8 @@ static void bcm63xx_init_irq(void)
- case BCM6368_CPU_ID:
- irq_stat_addr0 += PERF_IRQSTAT_6368_REG(0);
- irq_mask_addr0 += PERF_IRQMASK_6368_REG(0);
-+ irq_stat_addr1 += PERF_IRQSTAT_6368_REG(1);
-+ irq_mask_addr1 += PERF_IRQMASK_6368_REG(1);
- irq_bits = 64;
- ext_irq_count = 6;
- is_ext_irq_cascaded = 1;
+++ /dev/null
-From 7c9d3fe01034adbb890aab7c44534658f89c211b Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Thu, 25 Apr 2013 15:35:12 +0200
-Subject: [PATCH 08/13] MIPS: BCM63XX: use a helper for getting the right
- register address
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/irq.c | 30 ++++++++++++++++++++++++------
- 1 file changed, 24 insertions(+), 6 deletions(-)
-
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -251,6 +251,20 @@ static inline u32 get_ext_irq_perf_reg(i
- return ext_irq_cfg_reg2;
- }
-
-+static inline u32 get_irq_stat_addr(int cpu)
-+{
-+ if (cpu == 0)
-+ return irq_stat_addr0;
-+ return irq_stat_addr1;
-+}
-+
-+static inline u32 get_irq_mask_addr(int cpu)
-+{
-+ if (cpu == 0)
-+ return irq_mask_addr0;
-+ return irq_mask_addr1;
-+}
-+
- static inline void handle_internal(int intbit)
- {
- if (is_ext_irq_cascaded &&
-@@ -274,13 +288,15 @@ void __dispatch_internal_##width(void)
- unsigned int src, tgt; \
- bool irqs_pending = false; \
- static int i; \
-+ u32 irq_stat_addr = get_irq_stat_addr(0); \
-+ u32 irq_mask_addr = get_irq_mask_addr(0); \
- \
- /* read registers in reverse order */ \
- for (src = 0, tgt = (width / 32); src < (width / 32); src++) { \
- u32 val; \
- \
-- val = bcm_readl(irq_stat_addr0 + src * sizeof(u32)); \
-- val &= bcm_readl(irq_mask_addr0 + src * sizeof(u32)); \
-+ val = bcm_readl(irq_stat_addr + src * sizeof(u32)); \
-+ val &= bcm_readl(irq_mask_addr + src * sizeof(u32)); \
- pending[--tgt] = val; \
- \
- if (val) \
-@@ -306,10 +322,11 @@ static void __internal_irq_mask_##width(
- u32 val; \
- unsigned reg = (irq / 32) ^ (width/32 - 1); \
- unsigned bit = irq & 0x1f; \
-+ u32 irq_mask_addr = get_irq_mask_addr(0); \
- \
-- val = bcm_readl(irq_mask_addr0 + reg * sizeof(u32)); \
-+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \
- val &= ~(1 << bit); \
-- bcm_writel(val, irq_mask_addr0 + reg * sizeof(u32)); \
-+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \
- } \
- \
- static void __internal_irq_unmask_##width(unsigned int irq) \
-@@ -317,10 +334,11 @@ static void __internal_irq_unmask_##widt
- u32 val; \
- unsigned reg = (irq / 32) ^ (width/32 - 1); \
- unsigned bit = irq & 0x1f; \
-+ u32 irq_mask_addr = get_irq_mask_addr(0); \
- \
-- val = bcm_readl(irq_mask_addr0 + reg * sizeof(u32)); \
-+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \
- val |= (1 << bit); \
-- bcm_writel(val, irq_mask_addr0 + reg * sizeof(u32)); \
-+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \
- }
-
- BUILD_IPIC_INTERNAL(32);
+++ /dev/null
-From 398337c57ebe3c704e0df5f569e6bd860ffe8914 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Fri, 26 Apr 2013 11:21:16 +0200
-Subject: [PATCH 09/13] MIPS: BCM63XX: add cpu argument to dispatch internal
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/irq.c | 14 +++++++-------
- 1 file changed, 7 insertions(+), 7 deletions(-)
-
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -19,8 +19,8 @@
- #include <bcm63xx_io.h>
- #include <bcm63xx_irq.h>
-
--static void __dispatch_internal_32(void) __maybe_unused;
--static void __dispatch_internal_64(void) __maybe_unused;
-+static void __dispatch_internal_32(int cpu) __maybe_unused;
-+static void __dispatch_internal_64(int cpu) __maybe_unused;
- static void __internal_irq_mask_32(unsigned int irq) __maybe_unused;
- static void __internal_irq_mask_64(unsigned int irq) __maybe_unused;
- static void __internal_irq_unmask_32(unsigned int irq) __maybe_unused;
-@@ -140,7 +140,7 @@ static inline void bcm63xx_init_irq(void
- #else /* ! BCMCPU_RUNTIME_DETECT */
-
- static u32 irq_stat_addr0, irq_mask_addr0, irq_stat_addr1, irq_mask_addr1;
--static void (*dispatch_internal)(void);
-+static void (*dispatch_internal)(int cpu);
- static int is_ext_irq_cascaded;
- static unsigned int ext_irq_count;
- static unsigned int ext_irq_start, ext_irq_end;
-@@ -282,14 +282,14 @@ static inline void handle_internal(int i
- */
-
- #define BUILD_IPIC_INTERNAL(width) \
--void __dispatch_internal_##width(void) \
-+void __dispatch_internal_##width(int cpu) \
- { \
- u32 pending[width / 32]; \
- unsigned int src, tgt; \
- bool irqs_pending = false; \
- static int i; \
-- u32 irq_stat_addr = get_irq_stat_addr(0); \
-- u32 irq_mask_addr = get_irq_mask_addr(0); \
-+ u32 irq_stat_addr = get_irq_stat_addr(cpu); \
-+ u32 irq_mask_addr = get_irq_mask_addr(cpu); \
- \
- /* read registers in reverse order */ \
- for (src = 0, tgt = (width / 32); src < (width / 32); src++) { \
-@@ -361,7 +361,7 @@ asmlinkage void plat_irq_dispatch(void)
- if (cause & CAUSEF_IP1)
- do_IRQ(1);
- if (cause & CAUSEF_IP2)
-- dispatch_internal();
-+ dispatch_internal(0);
- if (!is_ext_irq_cascaded) {
- if (cause & CAUSEF_IP3)
- do_IRQ(IRQ_EXT_0);
+++ /dev/null
-From 7b8e7bc9806b61be2f07bf2bbb5e3ee6e0f333e9 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sun, 21 Apr 2013 15:38:56 +0200
-Subject: [PATCH 10/13] MIPS: BCM63XX: protect irq register accesses with a
- spinlock
-
-Since IRQs can be handled on both CPUs, we need to ensure that we
-don't try to modify the IRQ registers at the same time.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/irq.c | 47 ++++++++++++++++++++++++++++++++++++++++++-----
- 1 file changed, 42 insertions(+), 5 deletions(-)
-
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -12,6 +12,7 @@
- #include <linux/interrupt.h>
- #include <linux/module.h>
- #include <linux/irq.h>
-+#include <linux/spinlock.h>
- #include <asm/irq_cpu.h>
- #include <asm/mipsregs.h>
- #include <bcm63xx_cpu.h>
-@@ -26,6 +27,9 @@ static void __internal_irq_mask_64(unsig
- static void __internal_irq_unmask_32(unsigned int irq) __maybe_unused;
- static void __internal_irq_unmask_64(unsigned int irq) __maybe_unused;
-
-+static DEFINE_SPINLOCK(ipic_lock);
-+static DEFINE_SPINLOCK(epic_lock);
-+
- #ifndef BCMCPU_RUNTIME_DETECT
- #ifdef CONFIG_BCM63XX_CPU_6328
- #define irq_stat_reg0 PERF_IRQSTAT_6328_REG(0)
-@@ -290,7 +294,9 @@ void __dispatch_internal_##width(int cpu
- static int i; \
- u32 irq_stat_addr = get_irq_stat_addr(cpu); \
- u32 irq_mask_addr = get_irq_mask_addr(cpu); \
-+ unsigned long flags; \
- \
-+ spin_lock_irqsave(&ipic_lock, flags); \
- /* read registers in reverse order */ \
- for (src = 0, tgt = (width / 32); src < (width / 32); src++) { \
- u32 val; \
-@@ -302,6 +308,7 @@ void __dispatch_internal_##width(int cpu
- if (val) \
- irqs_pending = true; \
- } \
-+ spin_unlock_irqrestore(&ipic_lock, flags); \
- \
- if (!irqs_pending) \
- return; \
-@@ -381,12 +388,20 @@ asmlinkage void plat_irq_dispatch(void)
- */
- static void bcm63xx_internal_irq_mask(struct irq_data *d)
- {
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&ipic_lock, flags);
- internal_irq_mask(d->irq - IRQ_INTERNAL_BASE);
-+ spin_unlock_irqrestore(&ipic_lock, flags);
- }
-
- static void bcm63xx_internal_irq_unmask(struct irq_data *d)
- {
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&ipic_lock, flags);
- internal_irq_unmask(d->irq - IRQ_INTERNAL_BASE);
-+ spin_unlock_irqrestore(&ipic_lock, flags);
- }
-
- /*
-@@ -397,8 +412,11 @@ static void bcm63xx_external_irq_mask(st
- {
- unsigned int irq = d->irq - IRQ_EXTERNAL_BASE;
- u32 reg, regaddr;
-+ unsigned long flags;
-
- regaddr = get_ext_irq_perf_reg(irq);
-+
-+ spin_lock_irqsave(&epic_lock, flags);
- reg = bcm_perf_readl(regaddr);
-
- if (BCMCPU_IS_6348())
-@@ -407,16 +425,24 @@ static void bcm63xx_external_irq_mask(st
- reg &= ~EXTIRQ_CFG_MASK(irq % 4);
-
- bcm_perf_writel(reg, regaddr);
-- if (is_ext_irq_cascaded)
-- internal_irq_mask(irq + ext_irq_start);
-+ spin_unlock_irqrestore(&epic_lock, flags);
-+
-+ if (is_ext_irq_cascaded) {
-+ struct irq_data *cd = irq_get_irq_data(irq + ext_irq_start);
-+
-+ bcm63xx_internal_irq_mask(cd);
-+ }
- }
-
- static void bcm63xx_external_irq_unmask(struct irq_data *d)
- {
- unsigned int irq = d->irq - IRQ_EXTERNAL_BASE;
- u32 reg, regaddr;
-+ unsigned long flags;
-
- regaddr = get_ext_irq_perf_reg(irq);
-+
-+ spin_lock_irqsave(&epic_lock, flags);
- reg = bcm_perf_readl(regaddr);
-
- if (BCMCPU_IS_6348())
-@@ -425,16 +451,22 @@ static void bcm63xx_external_irq_unmask(
- reg |= EXTIRQ_CFG_MASK(irq % 4);
-
- bcm_perf_writel(reg, regaddr);
-+ spin_unlock_irqrestore(&epic_lock, flags);
-+
-+ if (is_ext_irq_cascaded) {
-+ struct irq_data *cd = irq_get_irq_data(irq + ext_irq_start);
-
-- if (is_ext_irq_cascaded)
-- internal_irq_unmask(irq + ext_irq_start);
-+ bcm63xx_internal_irq_unmask(cd);
-+ }
- }
-
- static void bcm63xx_external_irq_clear(struct irq_data *d)
- {
- unsigned int irq = d->irq - IRQ_EXTERNAL_BASE;
- u32 reg, regaddr;
-+ unsigned long flags;
-
-+ spin_lock_irqsave(&epic_lock, flags);
- regaddr = get_ext_irq_perf_reg(irq);
- reg = bcm_perf_readl(regaddr);
-
-@@ -444,6 +476,7 @@ static void bcm63xx_external_irq_clear(s
- reg |= EXTIRQ_CFG_CLEAR(irq % 4);
-
- bcm_perf_writel(reg, regaddr);
-+ spin_unlock_irqrestore(&epic_lock, flags);
- }
-
- static int bcm63xx_external_irq_set_type(struct irq_data *d,
-@@ -452,6 +485,7 @@ static int bcm63xx_external_irq_set_type
- unsigned int irq = d->irq - IRQ_EXTERNAL_BASE;
- u32 reg, regaddr;
- int levelsense, sense, bothedge;
-+ unsigned long flags;
-
- flow_type &= IRQ_TYPE_SENSE_MASK;
-
-@@ -486,9 +520,11 @@ static int bcm63xx_external_irq_set_type
- }
-
- regaddr = get_ext_irq_perf_reg(irq);
-- reg = bcm_perf_readl(regaddr);
- irq %= 4;
-
-+ spin_lock_irqsave(&epic_lock, flags);
-+ reg = bcm_perf_readl(regaddr);
-+
- switch (bcm63xx_get_cpu_id()) {
- case BCM6348_CPU_ID:
- if (levelsense)
-@@ -529,6 +565,7 @@ static int bcm63xx_external_irq_set_type
- }
-
- bcm_perf_writel(reg, regaddr);
-+ spin_unlock_irqrestore(&epic_lock, flags);
-
- irqd_set_trigger_type(d, flow_type);
- if (flow_type & (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH))
+++ /dev/null
-From 1baec3216529f795905b6376f9c8e4f14b114ba2 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Fri, 26 Apr 2013 12:03:15 +0200
-Subject: [PATCH 11/13] MIPS: BCM63XX: wire up the second CPU's irq line
-
-It's hardwired to IRQ3, so we don't need to actually check the CPU id.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/irq.c | 40 ++++++++++++++++++++++++++++++++--------
- 1 file changed, 32 insertions(+), 8 deletions(-)
-
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -329,11 +329,15 @@ static void __internal_irq_mask_##width(
- u32 val; \
- unsigned reg = (irq / 32) ^ (width/32 - 1); \
- unsigned bit = irq & 0x1f; \
-- u32 irq_mask_addr = get_irq_mask_addr(0); \
-+ int cpu; \
- \
-- val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \
-- val &= ~(1 << bit); \
-- bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \
-+ for_each_online_cpu(cpu) { \
-+ u32 irq_mask_addr = get_irq_mask_addr(cpu); \
-+ \
-+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \
-+ val &= ~(1 << bit); \
-+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \
-+ } \
- } \
- \
- static void __internal_irq_unmask_##width(unsigned int irq) \
-@@ -341,11 +345,15 @@ static void __internal_irq_unmask_##widt
- u32 val; \
- unsigned reg = (irq / 32) ^ (width/32 - 1); \
- unsigned bit = irq & 0x1f; \
-- u32 irq_mask_addr = get_irq_mask_addr(0); \
-+ int cpu; \
-+ \
-+ for_each_online_cpu(cpu) { \
-+ u32 irq_mask_addr = get_irq_mask_addr(cpu); \
- \
-- val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \
-- val |= (1 << bit); \
-- bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \
-+ val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \
-+ val |= (1 << bit); \
-+ bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \
-+ } \
- }
-
- BUILD_IPIC_INTERNAL(32);
-@@ -369,6 +377,10 @@ asmlinkage void plat_irq_dispatch(void)
- do_IRQ(1);
- if (cause & CAUSEF_IP2)
- dispatch_internal(0);
-+#ifdef CONFIG_SMP
-+ if (cause & CAUSEF_IP3)
-+ dispatch_internal(1);
-+#else
- if (!is_ext_irq_cascaded) {
- if (cause & CAUSEF_IP3)
- do_IRQ(IRQ_EXT_0);
-@@ -379,6 +391,7 @@ asmlinkage void plat_irq_dispatch(void)
- if (cause & CAUSEF_IP6)
- do_IRQ(IRQ_EXT_3);
- }
-+#endif
- } while (1);
- }
-
-@@ -598,6 +611,14 @@ static struct irqaction cpu_ip2_cascade_
- .flags = IRQF_NO_THREAD,
- };
-
-+#ifdef CONFIG_SMP
-+static struct irqaction cpu_ip3_cascade_action = {
-+ .handler = no_action,
-+ .name = "cascade_ip3",
-+ .flags = IRQF_NO_THREAD,
-+};
-+#endif
-+
- static struct irqaction cpu_ext_cascade_action = {
- .handler = no_action,
- .name = "cascade_extirq",
-@@ -624,4 +645,7 @@ void __init arch_init_irq(void)
- }
-
- setup_irq(MIPS_CPU_IRQ_BASE + 2, &cpu_ip2_cascade_action);
-+#ifdef CONFIG_SMP
-+ setup_irq(MIPS_CPU_IRQ_BASE + 3, &cpu_ip3_cascade_action);
-+#endif
- }
+++ /dev/null
-From 8679976d2ec08db4e4a14ecdd1ee022b70e51fc6 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Tue, 30 Apr 2013 11:26:53 +0200
-Subject: [PATCH 12/13] MIPS: BCM63XX: add cpumask argument to unmask
-
-Allow selective unmasking of IPIC irqs.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/irq.c | 19 +++++++++++++------
- 1 file changed, 13 insertions(+), 6 deletions(-)
-
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -24,8 +24,10 @@ static void __dispatch_internal_32(int c
- static void __dispatch_internal_64(int cpu) __maybe_unused;
- static void __internal_irq_mask_32(unsigned int irq) __maybe_unused;
- static void __internal_irq_mask_64(unsigned int irq) __maybe_unused;
--static void __internal_irq_unmask_32(unsigned int irq) __maybe_unused;
--static void __internal_irq_unmask_64(unsigned int irq) __maybe_unused;
-+static void __internal_irq_unmask_32(unsigned int irq,
-+ const struct cpumask *dest) __maybe_unused;
-+static void __internal_irq_unmask_64(unsigned int irq,
-+ const struct cpumask *dest) __maybe_unused;
-
- static DEFINE_SPINLOCK(ipic_lock);
- static DEFINE_SPINLOCK(epic_lock);
-@@ -150,7 +152,8 @@ static unsigned int ext_irq_count;
- static unsigned int ext_irq_start, ext_irq_end;
- static unsigned int ext_irq_cfg_reg1, ext_irq_cfg_reg2;
- static void (*internal_irq_mask)(unsigned int irq);
--static void (*internal_irq_unmask)(unsigned int irq);
-+static void (*internal_irq_unmask)(unsigned int irq,
-+ const struct cpumask *dest);
-
- static void bcm63xx_init_irq(void)
- {
-@@ -340,7 +343,8 @@ static void __internal_irq_mask_##width(
- } \
- } \
- \
--static void __internal_irq_unmask_##width(unsigned int irq) \
-+static void __internal_irq_unmask_##width(unsigned int irq, \
-+ const struct cpumask *dest) \
- { \
- u32 val; \
- unsigned reg = (irq / 32) ^ (width/32 - 1); \
-@@ -351,7 +355,10 @@ static void __internal_irq_unmask_##widt
- u32 irq_mask_addr = get_irq_mask_addr(cpu); \
- \
- val = bcm_readl(irq_mask_addr + reg * sizeof(u32)); \
-- val |= (1 << bit); \
-+ if (cpu_isset(cpu, *dest)) \
-+ val |= (1 << bit); \
-+ else \
-+ val &= ~(1 << bit); \
- bcm_writel(val, irq_mask_addr + reg * sizeof(u32)); \
- } \
- }
-@@ -413,7 +420,7 @@ static void bcm63xx_internal_irq_unmask(
- unsigned long flags;
-
- spin_lock_irqsave(&ipic_lock, flags);
-- internal_irq_unmask(d->irq - IRQ_INTERNAL_BASE);
-+ internal_irq_unmask(d->irq - IRQ_INTERNAL_BASE, cpu_online_mask);
- spin_unlock_irqrestore(&ipic_lock, flags);
- }
-
+++ /dev/null
-From a8bb19e5ba9a3a73fe6a761295b67b641a7bc9df Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Fri, 26 Apr 2013 12:06:03 +0200
-Subject: [PATCH 13/13] MIPS: BCM63XX: allow setting affinity for IPIC
-
-Add support for setting the SMP affinity for the IPIC IRQs.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/irq.c | 27 ++++++++++++++++++++++++++-
- 1 file changed, 26 insertions(+), 1 deletion(-)
-
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -418,9 +418,14 @@ static void bcm63xx_internal_irq_mask(st
- static void bcm63xx_internal_irq_unmask(struct irq_data *d)
- {
- unsigned long flags;
-+ const struct cpumask *dest = cpu_online_mask;
-
- spin_lock_irqsave(&ipic_lock, flags);
-- internal_irq_unmask(d->irq - IRQ_INTERNAL_BASE, cpu_online_mask);
-+#ifdef CONFIG_SMP
-+ if (irqd_affinity_was_set(d))
-+ dest = d->affinity;
-+#endif
-+ internal_irq_unmask(d->irq - IRQ_INTERNAL_BASE, dest);
- spin_unlock_irqrestore(&ipic_lock, flags);
- }
-
-@@ -596,10 +601,30 @@ static int bcm63xx_external_irq_set_type
- return IRQ_SET_MASK_OK_NOCOPY;
- }
-
-+#ifdef CONFIG_SMP
-+static int bcm63xx_internal_set_affinity(struct irq_data *data,
-+ const struct cpumask *dest,
-+ bool force)
-+{
-+ unsigned int irq = data->irq - IRQ_INTERNAL_BASE;
-+ unsigned long flags;
-+
-+ spin_lock_irqsave(&ipic_lock, flags);
-+ if (!irqd_irq_disabled(data))
-+ internal_irq_unmask(irq, dest);
-+ spin_unlock_irqrestore(&ipic_lock, flags);
-+
-+ return 0;
-+}
-+#endif
-+
- static struct irq_chip bcm63xx_internal_irq_chip = {
- .name = "bcm63xx_ipic",
- .irq_mask = bcm63xx_internal_irq_mask,
- .irq_unmask = bcm63xx_internal_irq_unmask,
-+#ifdef CONFIG_SMP
-+ .irq_set_affinity = bcm63xx_internal_set_affinity,
-+#endif
- };
-
- static struct irq_chip bcm63xx_external_irq_chip = {
+++ /dev/null
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_board.h
-@@ -1,6 +1,8 @@
- #ifndef BCM63XX_BOARD_H_
- #define BCM63XX_BOARD_H_
-
-+#include <asm/bootinfo.h>
-+
- const char *board_get_name(void);
-
- void board_prom_init(void);
-@@ -9,4 +11,8 @@ void board_setup(void);
-
- int board_register_devices(void);
-
-+static inline bool bcm63xx_is_cfe_present(void) {
-+ return fw_arg3 == 0x43464531;
-+}
-+
- #endif /* ! BCM63XX_BOARD_H_ */
+++ /dev/null
---- a/drivers/mtd/bcm63xxpart.c
-+++ b/drivers/mtd/bcm63xxpart.c
-@@ -35,7 +35,7 @@
-
- #include <linux/bcm963xx_tag.h>
- #include <asm/mach-bcm63xx/bcm63xx_nvram.h>
--#include <asm/mach-bcm63xx/board_bcm963xx.h>
-+#include <asm/mach-bcm63xx/bcm63xx_board.h>
-
- #define BCM63XX_EXTENDED_SIZE 0xBFC00000 /* Extended flash address */
-
-@@ -43,30 +43,6 @@
-
- #define BCM63XX_CFE_MAGIC_OFFSET 0x4e0
-
--static int bcm63xx_detect_cfe(struct mtd_info *master)
--{
-- char buf[9];
-- int ret;
-- size_t retlen;
--
-- ret = mtd_read(master, BCM963XX_CFE_VERSION_OFFSET, 5, &retlen,
-- (void *)buf);
-- buf[retlen] = 0;
--
-- if (ret)
-- return ret;
--
-- if (strncmp("cfe-v", buf, 5) == 0)
-- return 0;
--
-- /* very old CFE's do not have the cfe-v string, so check for magic */
-- ret = mtd_read(master, BCM63XX_CFE_MAGIC_OFFSET, 8, &retlen,
-- (void *)buf);
-- buf[retlen] = 0;
--
-- return strncmp("CFE1CFE1", buf, 8);
--}
--
- static int bcm63xx_parse_cfe_partitions(struct mtd_info *master,
- struct mtd_partition **pparts,
- struct mtd_part_parser_data *data)
-@@ -85,7 +61,7 @@ static int bcm63xx_parse_cfe_partitions(
- u32 computed_crc;
- bool rootfs_first = false;
-
-- if (bcm63xx_detect_cfe(master))
-+ if (!bcm63xx_is_cfe_present())
- return -EINVAL;
-
- cfe_erasesize = max_t(uint32_t, master->erasesize,
+++ /dev/null
-From a4d005c91d403d9f3d0272db6cc46202c06ec774 Mon Sep 17 00:00:00 2001
-From: Axel Gembe <ago@bastart.eu.org>
-Date: Mon, 12 May 2008 18:54:09 +0200
-Subject: [PATCH] bcm963xx: flashmap support
-
-Signed-off-by: Axel Gembe <ago@bastart.eu.org>
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 19 +----------------
- drivers/mtd/maps/bcm963xx-flash.c | 32 ++++++++++++++++++++++++----
- drivers/mtd/redboot.c | 13 +++++++++--
- 3 files changed, 38 insertions(+), 26 deletions(-)
-
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -30,7 +30,7 @@ static struct mtd_partition mtd_partitio
- }
- };
-
--static const char *bcm63xx_part_types[] = { "bcm63xxpart", NULL };
-+static const char *bcm63xx_part_types[] = { "bcm63xxpart", "RedBoot", NULL };
-
- static struct physmap_flash_data flash_data = {
- .width = 2,
---- a/drivers/mtd/redboot.c
-+++ b/drivers/mtd/redboot.c
-@@ -72,6 +72,7 @@ static int parse_redboot_partitions(stru
- int nulllen = 0;
- int numslots;
- unsigned long offset;
-+ unsigned long fis_origin = 0;
- #ifdef CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED
- static char nullstring[] = "unallocated";
- #endif
-@@ -176,6 +177,16 @@ static int parse_redboot_partitions(stru
- goto out;
- }
-
-+ if (data && data->origin) {
-+ fis_origin = data->origin;
-+ } else {
-+ for (i = 0; i < numslots; i++) {
-+ if (!strncmp(buf[i].name, "RedBoot", 8)) {
-+ fis_origin = (buf[i].flash_base & (master->size << 1) - 1);
-+ }
-+ }
-+ }
-+
- for (i = 0; i < numslots; i++) {
- struct fis_list *new_fl, **prev;
-
-@@ -196,10 +207,10 @@ static int parse_redboot_partitions(stru
- goto out;
- }
- new_fl->img = &buf[i];
-- if (data && data->origin)
-- buf[i].flash_base -= data->origin;
-- else
-- buf[i].flash_base &= master->size-1;
-+ if (fis_origin)
-+ buf[i].flash_base -= fis_origin;
-+
-+ buf[i].flash_base &= (master->size << 1) - 1;
-
- /* I'm sure the JFFS2 code has done me permanent damage.
- * I now think the following is _normal_
+++ /dev/null
---- a/include/uapi/linux/bcm963xx_tag.h
-+++ b/include/uapi/linux/bcm963xx_tag.h
-@@ -85,8 +85,10 @@ struct bcm_tag {
- __u32 rootfs_crc;
- /* 224-227: CRC32 of kernel partition */
- __u32 kernel_crc;
-- /* 228-235: Unused at present */
-- char reserved1[8];
-+ /* 228-231: Image sequence number */
-+ char image_sequence[4];
-+ /* 222-235: Openwrt: real rootfs length */
-+ __u32 real_rootfs_length;
- /* 236-239: CRC32 of header excluding last 20 bytes */
- __u32 header_crc;
- /* 240-255: Unused at present */
---- a/drivers/mtd/bcm63xxpart.c
-+++ b/drivers/mtd/bcm63xxpart.c
-@@ -110,7 +110,8 @@ static int bcm63xx_parse_cfe_partitions(
- } else {
- /* OpenWrt layout */
- rootfsaddr = kerneladdr + kernellen;
-- rootfslen = spareaddr - rootfsaddr;
-+ rootfslen = buf->real_rootfs_length;
-+ spareaddr = rootfsaddr + rootfslen;
- }
- } else {
- pr_warn("CFE boot tag CRC invalid (expected %08x, actual %08x)\n",
+++ /dev/null
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-@@ -1515,7 +1515,7 @@ static int compute_hw_mtu(struct bcm_ene
- actual_mtu = mtu;
-
- /* add ethernet header + vlan tag size */
-- actual_mtu += VLAN_ETH_HLEN;
-+ actual_mtu += VLAN_ETH_HLEN + VLAN_HLEN;
-
- if (actual_mtu < 64 || actual_mtu > BCMENET_MAX_MTU)
- return -EINVAL;
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -859,6 +859,8 @@ void __init board_prom_init(void)
- if (BCMCPU_IS_6348())
- val |= GPIO_MODE_6348_G3_EXT_MII |
- GPIO_MODE_6348_G0_EXT_MII;
-+ else if (BCMCPU_IS_6358())
-+ val |= GPIO_MODE_6358_ENET1_MII_CLK_INV;
- }
-
- bcm_gpio_writel(val, GPIO_MODE_REG);
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -578,6 +578,8 @@
- #define GPIO_MODE_6358_EXTRA_SPI_SS (1 << 7)
- #define GPIO_MODE_6358_SERIAL_LED (1 << 10)
- #define GPIO_MODE_6358_UTOPIA (1 << 12)
-+#define GPIO_MODE_6358_ENET1_MII_CLK_INV (1 << 30)
-+#define GPIO_MODE_6358_ENET0_MII_CLK_INV (1 << 31)
-
- #define GPIO_MODE_6368_ANALOG_AFE_0 (1 << 0)
- #define GPIO_MODE_6368_ANALOG_AFE_1 (1 << 1)
+++ /dev/null
-From b11218c750ab92cfab4408a0328f1b36ceec3f33 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Fri, 6 Jan 2012 12:24:18 +0100
-Subject: [PATCH 19/63] NET: bcm63xx_enet: move phy_(dis)connect into probe/remove
-
-Only connect/disconnect the phy during probe and remove, not during any
-open/close. The phy seldom changes during the runtime, and disconnecting
-the phy during close will prevent it from keeping any configuration over
-a down/up cycle.
-
-Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
----
- drivers/net/ethernet/broadcom/bcm63xx_enet.c | 84 +++++++++++++-------------
- 1 files changed, 41 insertions(+), 43 deletions(-)
-
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-@@ -784,10 +784,8 @@ static int bcm_enet_open(struct net_devi
- struct bcm_enet_priv *priv;
- struct sockaddr addr;
- struct device *kdev;
-- struct phy_device *phydev;
- int i, ret;
- unsigned int size;
-- char phy_id[MII_BUS_ID_SIZE + 3];
- void *p;
- u32 val;
-
-@@ -795,40 +793,10 @@ static int bcm_enet_open(struct net_devi
- kdev = &priv->pdev->dev;
-
- if (priv->has_phy) {
-- /* connect to PHY */
-- snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT,
-- priv->mii_bus->id, priv->phy_id);
--
-- phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, 0,
-- PHY_INTERFACE_MODE_MII);
--
-- if (IS_ERR(phydev)) {
-- dev_err(kdev, "could not attach to PHY\n");
-- return PTR_ERR(phydev);
-- }
--
-- /* mask with MAC supported features */
-- phydev->supported &= (SUPPORTED_10baseT_Half |
-- SUPPORTED_10baseT_Full |
-- SUPPORTED_100baseT_Half |
-- SUPPORTED_100baseT_Full |
-- SUPPORTED_Autoneg |
-- SUPPORTED_Pause |
-- SUPPORTED_MII);
-- phydev->advertising = phydev->supported;
--
-- if (priv->pause_auto && priv->pause_rx && priv->pause_tx)
-- phydev->advertising |= SUPPORTED_Pause;
-- else
-- phydev->advertising &= ~SUPPORTED_Pause;
--
-- dev_info(kdev, "attached PHY at address %d [%s]\n",
-- phydev->addr, phydev->drv->name);
--
-+ /* Reset state */
- priv->old_link = 0;
- priv->old_duplex = -1;
- priv->old_pause = -1;
-- priv->phydev = phydev;
- }
-
- /* mask all interrupts and request them */
-@@ -838,7 +806,7 @@ static int bcm_enet_open(struct net_devi
-
- ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev);
- if (ret)
-- goto out_phy_disconnect;
-+ return ret;
-
- ret = request_irq(priv->irq_rx, bcm_enet_isr_dma, IRQF_DISABLED,
- dev->name, dev);
-@@ -1025,9 +993,6 @@ out_freeirq_rx:
- out_freeirq:
- free_irq(dev->irq, dev);
-
--out_phy_disconnect:
-- phy_disconnect(priv->phydev);
--
- return ret;
- }
-
-@@ -1132,12 +1097,6 @@ static int bcm_enet_stop(struct net_devi
- free_irq(priv->irq_rx, dev);
- free_irq(dev->irq, dev);
-
-- /* release phy */
-- if (priv->has_phy) {
-- phy_disconnect(priv->phydev);
-- priv->phydev = NULL;
-- }
--
- return 0;
- }
-
-@@ -1708,6 +1667,8 @@ static int bcm_enet_probe(struct platfor
-
- /* MII bus registration */
- if (priv->has_phy) {
-+ struct phy_device *phydev;
-+ char phy_id[MII_BUS_ID_SIZE + 3];
-
- priv->mii_bus = mdiobus_alloc();
- if (!priv->mii_bus) {
-@@ -1745,6 +1706,38 @@ static int bcm_enet_probe(struct platfor
- dev_err(&pdev->dev, "unable to register mdio bus\n");
- goto out_free_mdio;
- }
-+
-+ /* connect to PHY */
-+ snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT,
-+ priv->mii_bus->id, priv->phy_id);
-+
-+ phydev = phy_connect(dev, phy_id, bcm_enet_adjust_phy_link, 0,
-+ PHY_INTERFACE_MODE_MII);
-+
-+ if (IS_ERR(phydev)) {
-+ dev_err(&pdev->dev, "could not attach to PHY\n");
-+ goto out_unregister_mdio;
-+ }
-+
-+ /* mask with MAC supported features */
-+ phydev->supported &= (SUPPORTED_10baseT_Half |
-+ SUPPORTED_10baseT_Full |
-+ SUPPORTED_100baseT_Half |
-+ SUPPORTED_100baseT_Full |
-+ SUPPORTED_Autoneg |
-+ SUPPORTED_Pause |
-+ SUPPORTED_MII);
-+ phydev->advertising = phydev->supported;
-+
-+ if (priv->pause_auto && priv->pause_rx && priv->pause_tx)
-+ phydev->advertising |= SUPPORTED_Pause;
-+ else
-+ phydev->advertising &= ~SUPPORTED_Pause;
-+
-+ dev_info(&pdev->dev, "attached PHY at address %d [%s]\n",
-+ phydev->addr, phydev->drv->name);
-+
-+ priv->phydev = phydev;
- } else {
-
- /* run platform code to initialize PHY device */
-@@ -1790,6 +1783,9 @@ static int bcm_enet_probe(struct platfor
- return 0;
-
- out_unregister_mdio:
-+ if (priv->phydev)
-+ phy_disconnect(priv->phydev);
-+
- if (priv->mii_bus)
- mdiobus_unregister(priv->mii_bus);
-
-@@ -1831,6 +1827,8 @@ static int bcm_enet_remove(struct platfo
- enet_writel(priv, 0, ENET_MIISC_REG);
-
- if (priv->has_phy) {
-+ phy_disconnect(priv->phydev);
-+ priv->phydev = NULL;
- mdiobus_unregister(priv->mii_bus);
- mdiobus_free(priv->mii_bus);
- } else {
+++ /dev/null
-From accc558f334662c8b16c121b4819931c028e8eb0 Mon Sep 17 00:00:00 2001
-From: Maxime Bizon <mbizon@freebox.fr>
-Date: Mon, 8 Jun 2009 16:12:10 +0200
-Subject: [PATCH 27/63] bcm63xx_enet: implement reset_autoneg ethtool.
-
----
- drivers/net/ethernet/broadcom/bcm63xx_enet.c | 15 +++++++++++++++
- 1 files changed, 15 insertions(+), 0 deletions(-)
-
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-@@ -1290,6 +1290,20 @@ static void bcm_enet_get_ethtool_stats(s
- mutex_unlock(&priv->mib_update_lock);
- }
-
-+static int bcm_enet_nway_reset(struct net_device *dev)
-+{
-+ struct bcm_enet_priv *priv;
-+
-+ priv = netdev_priv(dev);
-+ if (priv->has_phy) {
-+ if (!priv->phydev)
-+ return -ENODEV;
-+ return genphy_restart_aneg(priv->phydev);
-+ }
-+
-+ return -EOPNOTSUPP;
-+}
-+
- static int bcm_enet_get_settings(struct net_device *dev,
- struct ethtool_cmd *cmd)
- {
-@@ -1432,6 +1446,7 @@ static const struct ethtool_ops bcm_enet
- .get_strings = bcm_enet_get_strings,
- .get_sset_count = bcm_enet_get_sset_count,
- .get_ethtool_stats = bcm_enet_get_ethtool_stats,
-+ .nway_reset = bcm_enet_nway_reset,
- .get_settings = bcm_enet_get_settings,
- .set_settings = bcm_enet_set_settings,
- .get_drvinfo = bcm_enet_get_drvinfo,
+++ /dev/null
-From 2e5b0197443fcb454ca88619e36bb33d7a79e3ea Mon Sep 17 00:00:00 2001
-From: Maxime Bizon <mbizon@freebox.fr>
-Date: Thu, 21 Jan 2010 17:50:54 +0100
-Subject: [PATCH] bcm63xx_enet: split dma registers access.
-
----
- arch/mips/bcm63xx/dev-enet.c | 23 +++-
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 4 +-
- drivers/net/ethernet/broadcom/bcm63xx_enet.c | 144 +++++++++++++---------
- 3 files changed, 111 insertions(+), 62 deletions(-)
-
---- a/arch/mips/bcm63xx/dev-enet.c
-+++ b/arch/mips/bcm63xx/dev-enet.c
-@@ -19,6 +19,16 @@ static struct resource shared_res[] = {
- .end = -1, /* filled at runtime */
- .flags = IORESOURCE_MEM,
- },
-+ {
-+ .start = -1, /* filled at runtime */
-+ .end = -1, /* filled at runtime */
-+ .flags = IORESOURCE_MEM,
-+ },
-+ {
-+ .start = -1, /* filled at runtime */
-+ .end = -1, /* filled at runtime */
-+ .flags = IORESOURCE_MEM,
-+ },
- };
-
- static struct platform_device bcm63xx_enet_shared_device = {
-@@ -110,10 +120,15 @@ int __init bcm63xx_enet_register(int uni
- if (!shared_device_registered) {
- shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA);
- shared_res[0].end = shared_res[0].start;
-- if (BCMCPU_IS_6338())
-- shared_res[0].end += (RSET_ENETDMA_SIZE / 2) - 1;
-- else
-- shared_res[0].end += (RSET_ENETDMA_SIZE) - 1;
-+ shared_res[0].end += (RSET_ENETDMA_SIZE) - 1;
-+
-+ shared_res[1].start = bcm63xx_regset_address(RSET_ENETDMAC);
-+ shared_res[1].end = shared_res[1].start;
-+ shared_res[1].end += RSET_ENETDMAC_SIZE(16) - 1;
-+
-+ shared_res[2].start = bcm63xx_regset_address(RSET_ENETDMAS);
-+ shared_res[2].end = shared_res[2].start;
-+ shared_res[2].end += RSET_ENETDMAS_SIZE(16) - 1;
-
- ret = platform_device_register(&bcm63xx_enet_shared_device);
- if (ret)
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-@@ -174,7 +174,9 @@ enum bcm63xx_regs_set {
- #define BCM_6358_RSET_SPI_SIZE 1804
- #define BCM_6368_RSET_SPI_SIZE 1804
- #define RSET_ENET_SIZE 2048
--#define RSET_ENETDMA_SIZE 2048
-+#define RSET_ENETDMA_SIZE 256
-+#define RSET_ENETDMAC_SIZE(chans) (16 * (chans))
-+#define RSET_ENETDMAS_SIZE(chans) (16 * (chans))
- #define RSET_ENETSW_SIZE 65536
- #define RSET_UART_SIZE 24
- #define RSET_HSSPI_SIZE 1536
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-@@ -41,8 +41,8 @@ static int copybreak __read_mostly = 128
- module_param(copybreak, int, 0);
- MODULE_PARM_DESC(copybreak, "Receive copy threshold");
-
--/* io memory shared between all devices */
--static void __iomem *bcm_enet_shared_base;
-+/* io registers memory shared between all devices */
-+static void __iomem *bcm_enet_shared_base[3];
-
- /*
- * io helpers to access mac registers
-@@ -63,13 +63,35 @@ static inline void enet_writel(struct bc
- */
- static inline u32 enet_dma_readl(struct bcm_enet_priv *priv, u32 off)
- {
-- return bcm_readl(bcm_enet_shared_base + off);
-+ return bcm_readl(bcm_enet_shared_base[0] + off);
- }
-
- static inline void enet_dma_writel(struct bcm_enet_priv *priv,
- u32 val, u32 off)
- {
-- bcm_writel(val, bcm_enet_shared_base + off);
-+ bcm_writel(val, bcm_enet_shared_base[0] + off);
-+}
-+
-+static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off)
-+{
-+ return bcm_readl(bcm_enet_shared_base[1] + off);
-+}
-+
-+static inline void enet_dmac_writel(struct bcm_enet_priv *priv,
-+ u32 val, u32 off)
-+{
-+ bcm_writel(val, bcm_enet_shared_base[1] + off);
-+}
-+
-+static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off)
-+{
-+ return bcm_readl(bcm_enet_shared_base[2] + off);
-+}
-+
-+static inline void enet_dmas_writel(struct bcm_enet_priv *priv,
-+ u32 val, u32 off)
-+{
-+ bcm_writel(val, bcm_enet_shared_base[2] + off);
- }
-
- /*
-@@ -353,8 +375,8 @@ static int bcm_enet_receive_queue(struct
- bcm_enet_refill_rx(dev);
-
- /* kick rx dma */
-- enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
-- ENETDMA_CHANCFG_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
-+ ENETDMAC_CHANCFG_REG(priv->rx_chan));
- }
-
- return processed;
-@@ -429,10 +451,10 @@ static int bcm_enet_poll(struct napi_str
- dev = priv->net_dev;
-
- /* ack interrupts */
-- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-- ENETDMA_IR_REG(priv->rx_chan));
-- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-- ENETDMA_IR_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IR_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IR_REG(priv->tx_chan));
-
- /* reclaim sent skb */
- tx_work_done = bcm_enet_tx_reclaim(dev, 0);
-@@ -451,10 +473,10 @@ static int bcm_enet_poll(struct napi_str
- napi_complete(napi);
-
- /* restore rx/tx interrupt */
-- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-- ENETDMA_IRMASK_REG(priv->rx_chan));
-- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-- ENETDMA_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IRMASK_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IRMASK_REG(priv->tx_chan));
-
- return rx_work_done;
- }
-@@ -497,8 +519,8 @@ static irqreturn_t bcm_enet_isr_dma(int
- priv = netdev_priv(dev);
-
- /* mask rx/tx interrupts */
-- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
-- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
-
- napi_schedule(&priv->napi);
-
-@@ -557,8 +579,8 @@ static int bcm_enet_start_xmit(struct sk
- wmb();
-
- /* kick tx dma */
-- enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
-- ENETDMA_CHANCFG_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
-+ ENETDMAC_CHANCFG_REG(priv->tx_chan));
-
- /* stop queue if no more desc available */
- if (!priv->tx_desc_count)
-@@ -801,8 +823,8 @@ static int bcm_enet_open(struct net_devi
-
- /* mask all interrupts and request them */
- enet_writel(priv, 0, ENET_IRMASK_REG);
-- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
-- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
-
- ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev);
- if (ret)
-@@ -891,28 +913,28 @@ static int bcm_enet_open(struct net_devi
- }
-
- /* write rx & tx ring addresses */
-- enet_dma_writel(priv, priv->rx_desc_dma,
-- ENETDMA_RSTART_REG(priv->rx_chan));
-- enet_dma_writel(priv, priv->tx_desc_dma,
-- ENETDMA_RSTART_REG(priv->tx_chan));
-+ enet_dmas_writel(priv, priv->rx_desc_dma,
-+ ENETDMAS_RSTART_REG(priv->rx_chan));
-+ enet_dmas_writel(priv, priv->tx_desc_dma,
-+ ENETDMAS_RSTART_REG(priv->tx_chan));
-
- /* clear remaining state ram for rx & tx channel */
-- enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->rx_chan));
-- enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->tx_chan));
-- enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->rx_chan));
-- enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->tx_chan));
-- enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->rx_chan));
-- enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->tx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan));
-
- /* set max rx/tx length */
- enet_writel(priv, priv->hw_mtu, ENET_RXMAXLEN_REG);
- enet_writel(priv, priv->hw_mtu, ENET_TXMAXLEN_REG);
-
- /* set dma maximum burst len */
-- enet_dma_writel(priv, BCMENET_DMA_MAXBURST,
-- ENETDMA_MAXBURST_REG(priv->rx_chan));
-- enet_dma_writel(priv, BCMENET_DMA_MAXBURST,
-- ENETDMA_MAXBURST_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, BCMENET_DMA_MAXBURST,
-+ ENETDMAC_MAXBURST_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, BCMENET_DMA_MAXBURST,
-+ ENETDMAC_MAXBURST_REG(priv->tx_chan));
-
- /* set correct transmit fifo watermark */
- enet_writel(priv, BCMENET_TX_FIFO_TRESH, ENET_TXWMARK_REG);
-@@ -930,26 +952,26 @@ static int bcm_enet_open(struct net_devi
- val |= ENET_CTL_ENABLE_MASK;
- enet_writel(priv, val, ENET_CTL_REG);
- enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG);
-- enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK,
-- ENETDMA_CHANCFG_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
-+ ENETDMAC_CHANCFG_REG(priv->rx_chan));
-
- /* watch "mib counters about to overflow" interrupt */
- enet_writel(priv, ENET_IR_MIB, ENET_IR_REG);
- enet_writel(priv, ENET_IR_MIB, ENET_IRMASK_REG);
-
- /* watch "packet transferred" interrupt in rx and tx */
-- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-- ENETDMA_IR_REG(priv->rx_chan));
-- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-- ENETDMA_IR_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IR_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IR_REG(priv->tx_chan));
-
- /* make sure we enable napi before rx interrupt */
- napi_enable(&priv->napi);
-
-- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-- ENETDMA_IRMASK_REG(priv->rx_chan));
-- enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK,
-- ENETDMA_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IRMASK_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IRMASK_REG(priv->tx_chan));
-
- if (priv->has_phy)
- phy_start(priv->phydev);
-@@ -1026,14 +1048,14 @@ static void bcm_enet_disable_dma(struct
- {
- int limit;
-
-- enet_dma_writel(priv, 0, ENETDMA_CHANCFG_REG(chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG_REG(chan));
-
- limit = 1000;
- do {
- u32 val;
-
-- val = enet_dma_readl(priv, ENETDMA_CHANCFG_REG(chan));
-- if (!(val & ENETDMA_CHANCFG_EN_MASK))
-+ val = enet_dmac_readl(priv, ENETDMAC_CHANCFG_REG(chan));
-+ if (!(val & ENETDMAC_CHANCFG_EN_MASK))
- break;
- udelay(1);
- } while (limit--);
-@@ -1059,8 +1081,8 @@ static int bcm_enet_stop(struct net_devi
-
- /* mask all interrupts */
- enet_writel(priv, 0, ENET_IRMASK_REG);
-- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan));
-- enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
-
- /* make sure no mib update is scheduled */
- cancel_work_sync(&priv->mib_update_task);
-@@ -1598,7 +1620,7 @@ static int bcm_enet_probe(struct platfor
-
- /* stop if shared driver failed, assume driver->probe will be
- * called in the same order we register devices (correct ?) */
-- if (!bcm_enet_shared_base)
-+ if (!bcm_enet_shared_base[0])
- return -ENODEV;
-
- res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-@@ -1883,14 +1905,24 @@ struct platform_driver bcm63xx_enet_driv
- static int bcm_enet_shared_probe(struct platform_device *pdev)
- {
- struct resource *res;
-+ void __iomem *p[3];
-+ unsigned int i;
-
-- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-- if (!res)
-- return -ENODEV;
-+ memset(bcm_enet_shared_base, 0, sizeof(bcm_enet_shared_base));
-
-- bcm_enet_shared_base = devm_request_and_ioremap(&pdev->dev, res);
-- if (!bcm_enet_shared_base)
-- return -ENOMEM;
-+ for (i = 0; i < 3; i++) {
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, i);
-+ if (!res)
-+ return -EINVAL;
-+
-+ p[i] = devm_request_and_ioremap(&pdev->dev, res);
-+ if (!p[i])
-+ return -ENOMEM;
-+
-+ bcm_enet_shared_base[i] = p;
-+ }
-+
-+ memcpy(bcm_enet_shared_base, p, sizeof(bcm_enet_shared_base));
-
- return 0;
- }
+++ /dev/null
-From d16c1a1410f6c35a835baaa445774b4421db6c96 Mon Sep 17 00:00:00 2001
-From: Maxime Bizon <mbizon@freebox.fr>
-Date: Sat, 23 Jan 2010 03:01:02 +0100
-Subject: [PATCH 8/8] bcm63xx_enet: add support for bcm6368 internal ethernet
- switch.
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 4 +
- arch/mips/bcm63xx/dev-enet.c | 113 ++-
- .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h | 28 +
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 50 +
- .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 2 +
- drivers/net/ethernet/broadcom/bcm63xx_enet.c | 1018 +++++++++++++++++++-
- drivers/net/ethernet/broadcom/bcm63xx_enet.h | 75 ++
- 8 files changed, 1239 insertions(+), 66 deletions(-)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -924,6 +924,10 @@ int __init board_register_devices(void)
- !bcm63xx_nvram_get_mac_address(board.enet1.mac_addr))
- bcm63xx_enet_register(1, &board.enet1);
-
-+ if (board.has_enetsw &&
-+ !bcm63xx_nvram_get_mac_address(board.enetsw.mac_addr))
-+ bcm63xx_enetsw_register(&board.enetsw);
-+
- if (board.has_usbd)
- bcm63xx_usbd_register(&board.usbd);
-
---- a/arch/mips/bcm63xx/dev-enet.c
-+++ b/arch/mips/bcm63xx/dev-enet.c
-@@ -104,6 +104,64 @@ static struct platform_device bcm63xx_en
- },
- };
-
-+static struct resource enetsw_res[] = {
-+ {
-+ /* start & end filled at runtime */
-+ .flags = IORESOURCE_MEM,
-+ },
-+ {
-+ /* start filled at runtime */
-+ .flags = IORESOURCE_IRQ,
-+ },
-+ {
-+ /* start filled at runtime */
-+ .flags = IORESOURCE_IRQ,
-+ },
-+};
-+
-+static struct bcm63xx_enetsw_platform_data enetsw_pd;
-+
-+static struct platform_device bcm63xx_enetsw_device = {
-+ .name = "bcm63xx_enetsw",
-+ .num_resources = ARRAY_SIZE(enetsw_res),
-+ .resource = enetsw_res,
-+ .dev = {
-+ .platform_data = &enetsw_pd,
-+ },
-+};
-+
-+static int __init register_shared(void)
-+{
-+ int ret, chan_count;
-+
-+ if (shared_device_registered)
-+ return 0;
-+
-+ shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA);
-+ shared_res[0].end = shared_res[0].start;
-+ shared_res[0].end += (RSET_ENETDMA_SIZE) - 1;
-+
-+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368())
-+ chan_count = 32;
-+ else
-+ chan_count = 16;
-+
-+ shared_res[1].start = bcm63xx_regset_address(RSET_ENETDMAC);
-+ shared_res[1].end = shared_res[1].start;
-+ shared_res[1].end += RSET_ENETDMAC_SIZE(chan_count) - 1;
-+
-+ shared_res[2].start = bcm63xx_regset_address(RSET_ENETDMAS);
-+ shared_res[2].end = shared_res[2].start;
-+ shared_res[2].end += RSET_ENETDMAS_SIZE(chan_count) - 1;
-+
-+ ret = platform_device_register(&bcm63xx_enet_shared_device);
-+ if (ret)
-+ return ret;
-+ shared_device_registered = 1;
-+
-+ return 0;
-+}
-+
- int __init bcm63xx_enet_register(int unit,
- const struct bcm63xx_enet_platform_data *pd)
- {
-@@ -117,24 +175,9 @@ int __init bcm63xx_enet_register(int uni
- if (unit == 1 && BCMCPU_IS_6338())
- return -ENODEV;
-
-- if (!shared_device_registered) {
-- shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA);
-- shared_res[0].end = shared_res[0].start;
-- shared_res[0].end += (RSET_ENETDMA_SIZE) - 1;
--
-- shared_res[1].start = bcm63xx_regset_address(RSET_ENETDMAC);
-- shared_res[1].end = shared_res[1].start;
-- shared_res[1].end += RSET_ENETDMAC_SIZE(16) - 1;
--
-- shared_res[2].start = bcm63xx_regset_address(RSET_ENETDMAS);
-- shared_res[2].end = shared_res[2].start;
-- shared_res[2].end += RSET_ENETDMAS_SIZE(16) - 1;
--
-- ret = platform_device_register(&bcm63xx_enet_shared_device);
-- if (ret)
-- return ret;
-- shared_device_registered = 1;
-- }
-+ ret = register_shared();
-+ if (ret)
-+ return ret;
-
- if (unit == 0) {
- enet0_res[0].start = bcm63xx_regset_address(RSET_ENET0);
-@@ -175,3 +218,37 @@ int __init bcm63xx_enet_register(int uni
- return ret;
- return 0;
- }
-+
-+int __init
-+bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd)
-+{
-+ int ret;
-+
-+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362() && !BCMCPU_IS_6368())
-+ return -ENODEV;
-+
-+ ret = register_shared();
-+ if (ret)
-+ return ret;
-+
-+ enetsw_res[0].start = bcm63xx_regset_address(RSET_ENETSW);
-+ enetsw_res[0].end = enetsw_res[0].start;
-+ enetsw_res[0].end += RSET_ENETSW_SIZE - 1;
-+ enetsw_res[1].start = bcm63xx_get_irq_number(IRQ_ENETSW_RXDMA0);
-+ enetsw_res[2].start = bcm63xx_get_irq_number(IRQ_ENETSW_TXDMA0);
-+ if (!enetsw_res[2].start)
-+ enetsw_res[2].start = -1;
-+
-+ memcpy(bcm63xx_enetsw_device.dev.platform_data, pd, sizeof(*pd));
-+
-+ if (BCMCPU_IS_6328())
-+ enetsw_pd.num_ports = ENETSW_PORTS_6328;
-+ else if (BCMCPU_IS_6362() || BCMCPU_IS_6368())
-+ enetsw_pd.num_ports = ENETSW_PORTS_6368;
-+
-+ ret = platform_device_register(&bcm63xx_enetsw_device);
-+ if (ret)
-+ return ret;
-+
-+ return 0;
-+}
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
-@@ -39,7 +39,35 @@ struct bcm63xx_enet_platform_data {
- int phy_id, int reg, int val));
- };
-
-+/*
-+ * on board ethernet switch platform data
-+ */
-+#define ENETSW_MAX_PORT 8
-+#define ENETSW_PORTS_6328 5 /* 4 FE PHY + 1 RGMII */
-+#define ENETSW_PORTS_6368 6 /* 4 FE PHY + 2 RGMII */
-+
-+#define ENETSW_RGMII_PORT0 4
-+
-+struct bcm63xx_enetsw_port {
-+ int used;
-+ int phy_id;
-+
-+ int bypass_link;
-+ int force_speed;
-+ int force_duplex_full;
-+
-+ const char *name;
-+};
-+
-+struct bcm63xx_enetsw_platform_data {
-+ char mac_addr[ETH_ALEN];
-+ int num_ports;
-+ struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT];
-+};
-+
- int __init bcm63xx_enet_register(int unit,
- const struct bcm63xx_enet_platform_data *pd);
-
-+int bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd);
-+
- #endif /* ! BCM63XX_DEV_ENET_H_ */
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -832,10 +832,60 @@
- * _REG relative to RSET_ENETSW
- *************************************************************************/
-
-+/* Port traffic control */
-+#define ENETSW_PTCTRL_REG(x) (0x0 + (x))
-+#define ENETSW_PTCTRL_RXDIS_MASK (1 << 0)
-+#define ENETSW_PTCTRL_TXDIS_MASK (1 << 1)
-+
-+/* Switch mode register */
-+#define ENETSW_SWMODE_REG (0xb)
-+#define ENETSW_SWMODE_FWD_EN_MASK (1 << 1)
-+
-+/* IMP override Register */
-+#define ENETSW_IMPOV_REG (0xe)
-+#define ENETSW_IMPOV_FORCE_MASK (1 << 7)
-+#define ENETSW_IMPOV_TXFLOW_MASK (1 << 5)
-+#define ENETSW_IMPOV_RXFLOW_MASK (1 << 4)
-+#define ENETSW_IMPOV_1000_MASK (1 << 3)
-+#define ENETSW_IMPOV_100_MASK (1 << 2)
-+#define ENETSW_IMPOV_FDX_MASK (1 << 1)
-+#define ENETSW_IMPOV_LINKUP_MASK (1 << 0)
-+
-+/* Port override Register */
-+#define ENETSW_PORTOV_REG(x) (0x58 + (x))
-+#define ENETSW_PORTOV_ENABLE_MASK (1 << 6)
-+#define ENETSW_PORTOV_TXFLOW_MASK (1 << 5)
-+#define ENETSW_PORTOV_RXFLOW_MASK (1 << 4)
-+#define ENETSW_PORTOV_1000_MASK (1 << 3)
-+#define ENETSW_PORTOV_100_MASK (1 << 2)
-+#define ENETSW_PORTOV_FDX_MASK (1 << 1)
-+#define ENETSW_PORTOV_LINKUP_MASK (1 << 0)
-+
-+/* MDIO control register */
-+#define ENETSW_MDIOC_REG (0xb0)
-+#define ENETSW_MDIOC_EXT_MASK (1 << 16)
-+#define ENETSW_MDIOC_REG_SHIFT 20
-+#define ENETSW_MDIOC_PHYID_SHIFT 25
-+#define ENETSW_MDIOC_RD_MASK (1 << 30)
-+#define ENETSW_MDIOC_WR_MASK (1 << 31)
-+
-+/* MDIO data register */
-+#define ENETSW_MDIOD_REG (0xb4)
-+
-+/* Global Management Configuration Register */
-+#define ENETSW_GMCR_REG (0x200)
-+#define ENETSW_GMCR_RST_MIB_MASK (1 << 0)
-+
- /* MIB register */
- #define ENETSW_MIB_REG(x) (0x2800 + (x) * 4)
- #define ENETSW_MIB_REG_COUNT 47
-
-+/* Jumbo control register port mask register */
-+#define ENETSW_JMBCTL_PORT_REG (0x4004)
-+
-+/* Jumbo control mib good frame register */
-+#define ENETSW_JMBCTL_MAXSIZE_REG (0x4008)
-+
-
- /*************************************************************************
- * _REG relative to RSET_OHCI_PRIV
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -25,6 +25,7 @@ struct board_info {
- /* enabled feature/device */
- unsigned int has_enet0:1;
- unsigned int has_enet1:1;
-+ unsigned int has_enetsw:1;
- unsigned int has_pci:1;
- unsigned int has_pccard:1;
- unsigned int has_ohci0:1;
-@@ -37,6 +38,7 @@ struct board_info {
- /* ethernet config */
- struct bcm63xx_enet_platform_data enet0;
- struct bcm63xx_enet_platform_data enet1;
-+ struct bcm63xx_enetsw_platform_data enetsw;
-
- /* USB config */
- struct bcm63xx_usbd_platform_data usbd;
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-@@ -59,6 +59,49 @@ static inline void enet_writel(struct bc
- }
-
- /*
-+ * io helpers to access switch registers
-+ */
-+static inline u32 enetsw_readl(struct bcm_enet_priv *priv, u32 off)
-+{
-+ /* printk("enetsw_readl at %p\n", priv->base + off); */
-+ return bcm_readl(priv->base + off);
-+}
-+
-+static inline void enetsw_writel(struct bcm_enet_priv *priv,
-+ u32 val, u32 off)
-+{
-+ /* printk("enetsw_writel %08x at %p\n", val, priv->base + off); */
-+ bcm_writel(val, priv->base + off);
-+}
-+
-+static inline u16 enetsw_readw(struct bcm_enet_priv *priv, u32 off)
-+{
-+ /* printk("enetsw_readw at %p\n", priv->base + off); */
-+ return bcm_readw(priv->base + off);
-+}
-+
-+static inline void enetsw_writew(struct bcm_enet_priv *priv,
-+ u16 val, u32 off)
-+{
-+ /* printk("enetsw_writew %04x at %p\n", val, priv->base + off); */
-+ bcm_writew(val, priv->base + off);
-+}
-+
-+static inline u8 enetsw_readb(struct bcm_enet_priv *priv, u32 off)
-+{
-+ /* printk("enetsw_readb at %p\n", priv->base + off); */
-+ return bcm_readb(priv->base + off);
-+}
-+
-+static inline void enetsw_writeb(struct bcm_enet_priv *priv,
-+ u8 val, u32 off)
-+{
-+ /* printk("enetsw_writeb %02x at %p\n", val, priv->base + off); */
-+ bcm_writeb(val, priv->base + off);
-+}
-+
-+
-+/*
- * io helpers to access shared registers
- */
- static inline u32 enet_dma_readl(struct bcm_enet_priv *priv, u32 off)
-@@ -218,7 +261,6 @@ static int bcm_enet_refill_rx(struct net
- if (!skb)
- break;
- priv->rx_skb[desc_idx] = skb;
--
- p = dma_map_single(&priv->pdev->dev, skb->data,
- priv->rx_skb_size,
- DMA_FROM_DEVICE);
-@@ -321,7 +363,8 @@ static int bcm_enet_receive_queue(struct
- }
-
- /* recycle packet if it's marked as bad */
-- if (unlikely(len_stat & DMADESC_ERR_MASK)) {
-+ if (!priv->enet_is_sw &&
-+ unlikely(len_stat & DMADESC_ERR_MASK)) {
- dev->stats.rx_errors++;
-
- if (len_stat & DMADESC_OVSIZE_MASK)
-@@ -552,6 +595,26 @@ static int bcm_enet_start_xmit(struct sk
- goto out_unlock;
- }
-
-+ /* pad small packets sent on a switch device */
-+ if (priv->enet_is_sw && skb->len < 64) {
-+ int needed = 64 - skb->len;
-+ char *data;
-+
-+ if (unlikely(skb_tailroom(skb) < needed)) {
-+ struct sk_buff *nskb;
-+
-+ nskb = skb_copy_expand(skb, 0, needed, GFP_ATOMIC);
-+ if (!nskb) {
-+ ret = NETDEV_TX_BUSY;
-+ goto out_unlock;
-+ }
-+ dev_kfree_skb(skb);
-+ skb = nskb;
-+ }
-+ data = skb_put(skb, needed);
-+ memset(data, 0, needed);
-+ }
-+
- /* point to the next available desc */
- desc = &priv->tx_desc_cpu[priv->tx_curr_desc];
- priv->tx_skb[priv->tx_curr_desc] = skb;
-@@ -931,9 +994,9 @@ static int bcm_enet_open(struct net_devi
- enet_writel(priv, priv->hw_mtu, ENET_TXMAXLEN_REG);
-
- /* set dma maximum burst len */
-- enet_dmac_writel(priv, BCMENET_DMA_MAXBURST,
-+ enet_dmac_writel(priv, priv->dma_maxburst,
- ENETDMAC_MAXBURST_REG(priv->rx_chan));
-- enet_dmac_writel(priv, BCMENET_DMA_MAXBURST,
-+ enet_dmac_writel(priv, priv->dma_maxburst,
- ENETDMAC_MAXBURST_REG(priv->tx_chan));
-
- /* set correct transmit fifo watermark */
-@@ -1529,7 +1592,7 @@ static int compute_hw_mtu(struct bcm_ene
- * it's appended
- */
- priv->rx_skb_size = ALIGN(actual_mtu + ETH_FCS_LEN,
-- BCMENET_DMA_MAXBURST * 4);
-+ priv->dma_maxburst * 4);
- return 0;
- }
-
-@@ -1636,6 +1699,9 @@ static int bcm_enet_probe(struct platfor
- return -ENOMEM;
- priv = netdev_priv(dev);
-
-+ priv->enet_is_sw = false;
-+ priv->dma_maxburst = BCMENET_DMA_MAXBURST;
-+
- ret = compute_hw_mtu(priv, dev->mtu);
- if (ret)
- goto out;
-@@ -1900,65 +1966,928 @@ struct platform_driver bcm63xx_enet_driv
- };
-
- /*
-- * reserve & remap memory space shared between all macs
-+ * switch mii access callbacks
- */
--static int bcm_enet_shared_probe(struct platform_device *pdev)
-+static int bcmenet_sw_mdio_read(struct bcm_enet_priv *priv,
-+ int ext, int phy_id, int location)
- {
-- struct resource *res;
-- void __iomem *p[3];
-- unsigned int i;
-+ u32 reg;
-+ int ret;
-
-- memset(bcm_enet_shared_base, 0, sizeof(bcm_enet_shared_base));
-+ spin_lock_bh(&priv->enetsw_mdio_lock);
-+ enetsw_writel(priv, 0, ENETSW_MDIOC_REG);
-
-- for (i = 0; i < 3; i++) {
-- res = platform_get_resource(pdev, IORESOURCE_MEM, i);
-- if (!res)
-- return -EINVAL;
-+ reg = ENETSW_MDIOC_RD_MASK |
-+ (phy_id << ENETSW_MDIOC_PHYID_SHIFT) |
-+ (location << ENETSW_MDIOC_REG_SHIFT);
-+
-+ if (ext)
-+ reg |= ENETSW_MDIOC_EXT_MASK;
-+
-+ enetsw_writel(priv, reg, ENETSW_MDIOC_REG);
-+ udelay(50);
-+ ret = enetsw_readw(priv, ENETSW_MDIOD_REG);
-+ spin_unlock_bh(&priv->enetsw_mdio_lock);
-+ return ret;
-+}
-
-- p[i] = devm_request_and_ioremap(&pdev->dev, res);
-- if (!p[i])
-- return -ENOMEM;
-+static void bcmenet_sw_mdio_write(struct bcm_enet_priv *priv,
-+ int ext, int phy_id, int location,
-+ uint16_t data)
-+{
-+ u32 reg;
-
-- bcm_enet_shared_base[i] = p;
-- }
-+ spin_lock_bh(&priv->enetsw_mdio_lock);
-+ enetsw_writel(priv, 0, ENETSW_MDIOC_REG);
-
-- memcpy(bcm_enet_shared_base, p, sizeof(bcm_enet_shared_base));
-+ reg = ENETSW_MDIOC_WR_MASK |
-+ (phy_id << ENETSW_MDIOC_PHYID_SHIFT) |
-+ (location << ENETSW_MDIOC_REG_SHIFT);
-
-- return 0;
--}
-+ if (ext)
-+ reg |= ENETSW_MDIOC_EXT_MASK;
-
--static int bcm_enet_shared_remove(struct platform_device *pdev)
--{
-- return 0;
-+ reg |= data;
-+
-+ enetsw_writel(priv, reg, ENETSW_MDIOC_REG);
-+ udelay(50);
-+ spin_unlock_bh(&priv->enetsw_mdio_lock);
- }
-
- /*
-- * this "shared" driver is needed because both macs share a single
-- * address space
-+ * enet sw PHY polling
- */
--struct platform_driver bcm63xx_enet_shared_driver = {
-- .probe = bcm_enet_shared_probe,
-- .remove = bcm_enet_shared_remove,
-- .driver = {
-- .name = "bcm63xx_enet_shared",
-- .owner = THIS_MODULE,
-- },
--};
-+static void swphy_poll_timer(unsigned long data)
-+{
-+ struct bcm_enet_priv *priv = (struct bcm_enet_priv *)data;
-+ unsigned int i;
-+
-+ for (i = 0; i < priv->num_ports; i++) {
-+ struct bcm63xx_enetsw_port *port;
-+ int val, j, up, advertise, lpa, lpa2, speed, duplex, media;
-+ int external_phy = bcm_enet_port_is_rgmii(i);
-+ u8 override;
-+
-+ port = &priv->used_ports[i];
-+ if (!port->used)
-+ continue;
-+
-+ if (port->bypass_link)
-+ continue;
-+
-+ /* dummy read to clear */
-+ for (j = 0; j < 2; j++)
-+ val = bcmenet_sw_mdio_read(priv, external_phy,
-+ port->phy_id, MII_BMSR);
-+
-+ if (val == 0xffff)
-+ continue;
-+
-+ up = (val & BMSR_LSTATUS) ? 1 : 0;
-+ if (!(up ^ priv->sw_port_link[i]))
-+ continue;
-+
-+ priv->sw_port_link[i] = up;
-+
-+ /* link changed */
-+ if (!up) {
-+ dev_info(&priv->pdev->dev, "link DOWN on %s\n",
-+ port->name);
-+ enetsw_writeb(priv, ENETSW_PORTOV_ENABLE_MASK,
-+ ENETSW_PORTOV_REG(i));
-+ enetsw_writeb(priv, ENETSW_PTCTRL_RXDIS_MASK |
-+ ENETSW_PTCTRL_TXDIS_MASK,
-+ ENETSW_PTCTRL_REG(i));
-+ continue;
-+ }
-+
-+ advertise = bcmenet_sw_mdio_read(priv, external_phy,
-+ port->phy_id, MII_ADVERTISE);
-+
-+ lpa = bcmenet_sw_mdio_read(priv, external_phy, port->phy_id,
-+ MII_LPA);
-+
-+ lpa2 = bcmenet_sw_mdio_read(priv, external_phy, port->phy_id,
-+ MII_STAT1000);
-+
-+ /* figure out media and duplex from advertise and LPA values */
-+ media = mii_nway_result(lpa & advertise);
-+ duplex = (media & ADVERTISE_FULL) ? 1 : 0;
-+ if (lpa2 & LPA_1000FULL)
-+ duplex = 1;
-+
-+ if (lpa2 & (LPA_1000FULL | LPA_1000HALF))
-+ speed = 1000;
-+ else {
-+ if (media & (ADVERTISE_100FULL | ADVERTISE_100HALF))
-+ speed = 100;
-+ else
-+ speed = 10;
-+ }
-+
-+ dev_info(&priv->pdev->dev,
-+ "link UP on %s, %dMbps, %s-duplex\n",
-+ port->name, speed, duplex ? "full" : "half");
-+
-+ override = ENETSW_PORTOV_ENABLE_MASK |
-+ ENETSW_PORTOV_LINKUP_MASK;
-+
-+ if (speed == 1000)
-+ override |= ENETSW_IMPOV_1000_MASK;
-+ else if (speed == 100)
-+ override |= ENETSW_IMPOV_100_MASK;
-+ if (duplex)
-+ override |= ENETSW_IMPOV_FDX_MASK;
-+
-+ enetsw_writeb(priv, override, ENETSW_PORTOV_REG(i));
-+ enetsw_writeb(priv, 0, ENETSW_PTCTRL_REG(i));
-+ }
-+
-+ priv->swphy_poll.expires = jiffies + HZ;
-+ add_timer(&priv->swphy_poll);
-+}
-
- /*
-- * entry point
-+ * open callback, allocate dma rings & buffers and start rx operation
- */
--static int __init bcm_enet_init(void)
-+static int bcm_enetsw_open(struct net_device *dev)
- {
-- int ret;
-+ struct bcm_enet_priv *priv;
-+ struct device *kdev;
-+ int i, ret;
-+ unsigned int size;
-+ void *p;
-+ u32 val;
-
-- ret = platform_driver_register(&bcm63xx_enet_shared_driver);
-- if (ret)
-- return ret;
-+ priv = netdev_priv(dev);
-+ kdev = &priv->pdev->dev;
-
-- ret = platform_driver_register(&bcm63xx_enet_driver);
-+ /* mask all interrupts and request them */
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
-+
-+ ret = request_irq(priv->irq_rx, bcm_enet_isr_dma,
-+ IRQF_DISABLED, dev->name, dev);
- if (ret)
-- platform_driver_unregister(&bcm63xx_enet_shared_driver);
-+ goto out_freeirq;
-+
-+ if (priv->irq_tx != -1) {
-+ ret = request_irq(priv->irq_tx, bcm_enet_isr_dma,
-+ IRQF_DISABLED, dev->name, dev);
-+ if (ret)
-+ goto out_freeirq_rx;
-+ }
-+
-+ /* allocate rx dma ring */
-+ size = priv->rx_ring_size * sizeof(struct bcm_enet_desc);
-+ p = dma_alloc_coherent(kdev, size, &priv->rx_desc_dma, GFP_KERNEL);
-+ if (!p) {
-+ dev_err(kdev, "cannot allocate rx ring %u\n", size);
-+ ret = -ENOMEM;
-+ goto out_freeirq_tx;
-+ }
-+
-+ memset(p, 0, size);
-+ priv->rx_desc_alloc_size = size;
-+ priv->rx_desc_cpu = p;
-+
-+ /* allocate tx dma ring */
-+ size = priv->tx_ring_size * sizeof(struct bcm_enet_desc);
-+ p = dma_alloc_coherent(kdev, size, &priv->tx_desc_dma, GFP_KERNEL);
-+ if (!p) {
-+ dev_err(kdev, "cannot allocate tx ring\n");
-+ ret = -ENOMEM;
-+ goto out_free_rx_ring;
-+ }
-+
-+ memset(p, 0, size);
-+ priv->tx_desc_alloc_size = size;
-+ priv->tx_desc_cpu = p;
-+
-+ priv->tx_skb = kzalloc(sizeof(struct sk_buff *) * priv->tx_ring_size,
-+ GFP_KERNEL);
-+ if (!priv->tx_skb) {
-+ dev_err(kdev, "cannot allocate rx skb queue\n");
-+ ret = -ENOMEM;
-+ goto out_free_tx_ring;
-+ }
-+
-+ priv->tx_desc_count = priv->tx_ring_size;
-+ priv->tx_dirty_desc = 0;
-+ priv->tx_curr_desc = 0;
-+ spin_lock_init(&priv->tx_lock);
-+
-+ /* init & fill rx ring with skbs */
-+ priv->rx_skb = kzalloc(sizeof(struct sk_buff *) * priv->rx_ring_size,
-+ GFP_KERNEL);
-+ if (!priv->rx_skb) {
-+ dev_err(kdev, "cannot allocate rx skb queue\n");
-+ ret = -ENOMEM;
-+ goto out_free_tx_skb;
-+ }
-+
-+ priv->rx_desc_count = 0;
-+ priv->rx_dirty_desc = 0;
-+ priv->rx_curr_desc = 0;
-+
-+ /* disable all ports */
-+ for (i = 0; i < priv->num_ports; i++) {
-+ enetsw_writeb(priv, ENETSW_PORTOV_ENABLE_MASK,
-+ ENETSW_PORTOV_REG(i));
-+ enetsw_writeb(priv, ENETSW_PTCTRL_RXDIS_MASK |
-+ ENETSW_PTCTRL_TXDIS_MASK,
-+ ENETSW_PTCTRL_REG(i));
-+
-+ priv->sw_port_link[i] = 0;
-+ }
-+
-+ /* reset mib */
-+ val = enetsw_readb(priv, ENETSW_GMCR_REG);
-+ val |= ENETSW_GMCR_RST_MIB_MASK;
-+ enetsw_writeb(priv, val, ENETSW_GMCR_REG);
-+ mdelay(1);
-+ val &= ~ENETSW_GMCR_RST_MIB_MASK;
-+ enetsw_writeb(priv, val, ENETSW_GMCR_REG);
-+ mdelay(1);
-+
-+ /* force CPU port state */
-+ val = enetsw_readb(priv, ENETSW_IMPOV_REG);
-+ val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK;
-+ enetsw_writeb(priv, val, ENETSW_IMPOV_REG);
-+
-+ /* enable switch forward engine */
-+ val = enetsw_readb(priv, ENETSW_SWMODE_REG);
-+ val |= ENETSW_SWMODE_FWD_EN_MASK;
-+ enetsw_writeb(priv, val, ENETSW_SWMODE_REG);
-+
-+ /* enable jumbo on all ports */
-+ enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG);
-+ enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG);
-+
-+ /* initialize flow control buffer allocation */
-+ enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
-+ ENETDMA_BUFALLOC_REG(priv->rx_chan));
-+
-+ if (bcm_enet_refill_rx(dev)) {
-+ dev_err(kdev, "cannot allocate rx skb queue\n");
-+ ret = -ENOMEM;
-+ goto out;
-+ }
-+
-+ /* write rx & tx ring addresses */
-+ enet_dmas_writel(priv, priv->rx_desc_dma,
-+ ENETDMAS_RSTART_REG(priv->rx_chan));
-+ enet_dmas_writel(priv, priv->tx_desc_dma,
-+ ENETDMAS_RSTART_REG(priv->tx_chan));
-+
-+ /* clear remaining state ram for rx & tx channel */
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan));
-+
-+ /* set dma maximum burst len */
-+ enet_dmac_writel(priv, priv->dma_maxburst,
-+ ENETDMAC_MAXBURST_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, priv->dma_maxburst,
-+ ENETDMAC_MAXBURST_REG(priv->tx_chan));
-+
-+ /* set flow control low/high threshold to 1/3 / 2/3 */
-+ val = priv->rx_ring_size / 3;
-+ enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan));
-+ val = (priv->rx_ring_size * 2) / 3;
-+ enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan));
-+
-+ /* all set, enable mac and interrupts, start dma engine and
-+ * kick rx dma channel */
-+ wmb();
-+ enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG);
-+ enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
-+ ENETDMAC_CHANCFG_REG(priv->rx_chan));
-+
-+ /* watch "packet transferred" interrupt in rx and tx */
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IR_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IR_REG(priv->tx_chan));
-+
-+ /* make sure we enable napi before rx interrupt */
-+ napi_enable(&priv->napi);
-+
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IRMASK_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-+ ENETDMAC_IRMASK_REG(priv->tx_chan));
-+
-+ netif_carrier_on(dev);
-+ netif_start_queue(dev);
-+
-+ /*
-+ * apply override config for bypass_link ports here.
-+ */
-+ for (i = 0; i < priv->num_ports; i++) {
-+ struct bcm63xx_enetsw_port *port;
-+ u8 override;
-+ port = &priv->used_ports[i];
-+ if (!port->used)
-+ continue;
-+
-+ if (!port->bypass_link)
-+ continue;
-+
-+ override = ENETSW_PORTOV_ENABLE_MASK |
-+ ENETSW_PORTOV_LINKUP_MASK;
-+
-+ switch (port->force_speed) {
-+ case 1000:
-+ override |= ENETSW_IMPOV_1000_MASK;
-+ break;
-+ case 100:
-+ override |= ENETSW_IMPOV_100_MASK;
-+ break;
-+ case 10:
-+ break;
-+ default:
-+ printk(KERN_WARNING "invalid forced speed on port %s: assume 10\n",
-+ port->name);
-+ break;
-+ }
-+
-+ if (port->force_duplex_full)
-+ override |= ENETSW_IMPOV_FDX_MASK;
-+
-+
-+ enetsw_writeb(priv, override, ENETSW_PORTOV_REG(i));
-+ enetsw_writeb(priv, 0, ENETSW_PTCTRL_REG(i));
-+ }
-+
-+ /* start phy polling timer */
-+ init_timer(&priv->swphy_poll);
-+ priv->swphy_poll.function = swphy_poll_timer;
-+ priv->swphy_poll.data = (unsigned long)priv;
-+ priv->swphy_poll.expires = jiffies;
-+ add_timer(&priv->swphy_poll);
-+ return 0;
-+
-+out:
-+ for (i = 0; i < priv->rx_ring_size; i++) {
-+ struct bcm_enet_desc *desc;
-+
-+ if (!priv->rx_skb[i])
-+ continue;
-+
-+ desc = &priv->rx_desc_cpu[i];
-+ dma_unmap_single(kdev, desc->address, priv->rx_skb_size,
-+ DMA_FROM_DEVICE);
-+ kfree_skb(priv->rx_skb[i]);
-+ }
-+ kfree(priv->rx_skb);
-+
-+out_free_tx_skb:
-+ kfree(priv->tx_skb);
-+
-+out_free_tx_ring:
-+ dma_free_coherent(kdev, priv->tx_desc_alloc_size,
-+ priv->tx_desc_cpu, priv->tx_desc_dma);
-+
-+out_free_rx_ring:
-+ dma_free_coherent(kdev, priv->rx_desc_alloc_size,
-+ priv->rx_desc_cpu, priv->rx_desc_dma);
-+
-+out_freeirq_tx:
-+ if (priv->irq_tx != -1)
-+ free_irq(priv->irq_tx, dev);
-+
-+out_freeirq_rx:
-+ free_irq(priv->irq_rx, dev);
-+
-+out_freeirq:
-+ return ret;
-+}
-+
-+/*
-+ * stop callback
-+ */
-+static int bcm_enetsw_stop(struct net_device *dev)
-+{
-+ struct bcm_enet_priv *priv;
-+ struct device *kdev;
-+ int i;
-+
-+ priv = netdev_priv(dev);
-+ kdev = &priv->pdev->dev;
-+
-+ del_timer_sync(&priv->swphy_poll);
-+ netif_stop_queue(dev);
-+ napi_disable(&priv->napi);
-+ del_timer_sync(&priv->rx_timeout);
-+
-+ /* mask all interrupts */
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
-+
-+ /* disable dma & mac */
-+ bcm_enet_disable_dma(priv, priv->tx_chan);
-+ bcm_enet_disable_dma(priv, priv->rx_chan);
-+
-+ /* force reclaim of all tx buffers */
-+ bcm_enet_tx_reclaim(dev, 1);
-+
-+ /* free the rx skb ring */
-+ for (i = 0; i < priv->rx_ring_size; i++) {
-+ struct bcm_enet_desc *desc;
-+
-+ if (!priv->rx_skb[i])
-+ continue;
-+
-+ desc = &priv->rx_desc_cpu[i];
-+ dma_unmap_single(kdev, desc->address, priv->rx_skb_size,
-+ DMA_FROM_DEVICE);
-+ kfree_skb(priv->rx_skb[i]);
-+ }
-+
-+ /* free remaining allocated memory */
-+ kfree(priv->rx_skb);
-+ kfree(priv->tx_skb);
-+ dma_free_coherent(kdev, priv->rx_desc_alloc_size,
-+ priv->rx_desc_cpu, priv->rx_desc_dma);
-+ dma_free_coherent(kdev, priv->tx_desc_alloc_size,
-+ priv->tx_desc_cpu, priv->tx_desc_dma);
-+ if (priv->irq_tx != -1)
-+ free_irq(priv->irq_tx, dev);
-+ free_irq(priv->irq_rx, dev);
-+
-+ return 0;
-+}
-+
-+/*
-+ * try to sort out phy external status by walking the used_port field
-+ * in the bcm_enet_priv structure. in case the phy address is not
-+ * assigned to any physical port on the switch, assume it is external
-+ * (and yell at the user).
-+ */
-+static int bcm_enetsw_phy_is_external(struct bcm_enet_priv *priv, int phy_id)
-+{
-+ int i;
-+
-+ for (i = 0; i < priv->num_ports; ++i) {
-+ if (!priv->used_ports[i].used)
-+ continue;
-+ if (priv->used_ports[i].phy_id == phy_id)
-+ return bcm_enet_port_is_rgmii(i);
-+ }
-+
-+ printk_once(KERN_WARNING "bcm63xx_enet: could not find a used port with phy_id %i, assuming phy is external\n",
-+ phy_id);
-+ return 1;
-+}
-+
-+/*
-+ * can't use bcmenet_sw_mdio_read directly as we need to sort out
-+ * external/internal status of the given phy_id first.
-+ */
-+static int bcm_enetsw_mii_mdio_read(struct net_device *dev, int phy_id,
-+ int location)
-+{
-+ struct bcm_enet_priv *priv;
-+
-+ priv = netdev_priv(dev);
-+ return bcmenet_sw_mdio_read(priv,
-+ bcm_enetsw_phy_is_external(priv, phy_id),
-+ phy_id, location);
-+}
-+
-+/*
-+ * can't use bcmenet_sw_mdio_write directly as we need to sort out
-+ * external/internal status of the given phy_id first.
-+ */
-+static void bcm_enetsw_mii_mdio_write(struct net_device *dev, int phy_id,
-+ int location,
-+ int val)
-+{
-+ struct bcm_enet_priv *priv;
-+
-+ priv = netdev_priv(dev);
-+ bcmenet_sw_mdio_write(priv, bcm_enetsw_phy_is_external(priv, phy_id),
-+ phy_id, location, val);
-+}
-+
-+static int bcm_enetsw_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
-+{
-+ struct mii_if_info mii;
-+
-+ mii.dev = dev;
-+ mii.mdio_read = bcm_enetsw_mii_mdio_read;
-+ mii.mdio_write = bcm_enetsw_mii_mdio_write;
-+ mii.phy_id = 0;
-+ mii.phy_id_mask = 0x3f;
-+ mii.reg_num_mask = 0x1f;
-+ return generic_mii_ioctl(&mii, if_mii(rq), cmd, NULL);
-+
-+}
-+
-+static const struct net_device_ops bcm_enetsw_ops = {
-+ .ndo_open = bcm_enetsw_open,
-+ .ndo_stop = bcm_enetsw_stop,
-+ .ndo_start_xmit = bcm_enet_start_xmit,
-+ .ndo_change_mtu = bcm_enet_change_mtu,
-+ .ndo_do_ioctl = bcm_enetsw_ioctl,
-+};
-+
-+
-+static const struct bcm_enet_stats bcm_enetsw_gstrings_stats[] = {
-+ { "rx_packets", DEV_STAT(rx_packets), -1 },
-+ { "tx_packets", DEV_STAT(tx_packets), -1 },
-+ { "rx_bytes", DEV_STAT(rx_bytes), -1 },
-+ { "tx_bytes", DEV_STAT(tx_bytes), -1 },
-+ { "rx_errors", DEV_STAT(rx_errors), -1 },
-+ { "tx_errors", DEV_STAT(tx_errors), -1 },
-+ { "rx_dropped", DEV_STAT(rx_dropped), -1 },
-+ { "tx_dropped", DEV_STAT(tx_dropped), -1 },
-+
-+ { "tx_good_octets", GEN_STAT(mib.tx_gd_octets), ETHSW_MIB_RX_GD_OCT },
-+ { "tx_unicast", GEN_STAT(mib.tx_unicast), ETHSW_MIB_RX_BRDCAST },
-+ { "tx_broadcast", GEN_STAT(mib.tx_brdcast), ETHSW_MIB_RX_BRDCAST },
-+ { "tx_multicast", GEN_STAT(mib.tx_mult), ETHSW_MIB_RX_MULT },
-+ { "tx_64_octets", GEN_STAT(mib.tx_64), ETHSW_MIB_RX_64 },
-+ { "tx_65_127_oct", GEN_STAT(mib.tx_65_127), ETHSW_MIB_RX_65_127 },
-+ { "tx_128_255_oct", GEN_STAT(mib.tx_128_255), ETHSW_MIB_RX_128_255 },
-+ { "tx_256_511_oct", GEN_STAT(mib.tx_256_511), ETHSW_MIB_RX_256_511 },
-+ { "tx_512_1023_oct", GEN_STAT(mib.tx_512_1023), ETHSW_MIB_RX_512_1023},
-+ { "tx_1024_1522_oct", GEN_STAT(mib.tx_1024_max),
-+ ETHSW_MIB_RX_1024_1522 },
-+ { "tx_1523_2047_oct", GEN_STAT(mib.tx_1523_2047),
-+ ETHSW_MIB_RX_1523_2047 },
-+ { "tx_2048_4095_oct", GEN_STAT(mib.tx_2048_4095),
-+ ETHSW_MIB_RX_2048_4095 },
-+ { "tx_4096_8191_oct", GEN_STAT(mib.tx_4096_8191),
-+ ETHSW_MIB_RX_4096_8191 },
-+ { "tx_8192_9728_oct", GEN_STAT(mib.tx_8192_9728),
-+ ETHSW_MIB_RX_8192_9728 },
-+ { "tx_oversize", GEN_STAT(mib.tx_ovr), ETHSW_MIB_RX_OVR },
-+ { "tx_oversize_drop", GEN_STAT(mib.tx_ovr), ETHSW_MIB_RX_OVR_DISC },
-+ { "tx_dropped", GEN_STAT(mib.tx_drop), ETHSW_MIB_RX_DROP },
-+ { "tx_undersize", GEN_STAT(mib.tx_underrun), ETHSW_MIB_RX_UND },
-+ { "tx_pause", GEN_STAT(mib.tx_pause), ETHSW_MIB_RX_PAUSE },
-+
-+ { "rx_good_octets", GEN_STAT(mib.rx_gd_octets), ETHSW_MIB_TX_ALL_OCT },
-+ { "rx_broadcast", GEN_STAT(mib.rx_brdcast), ETHSW_MIB_TX_BRDCAST },
-+ { "rx_multicast", GEN_STAT(mib.rx_mult), ETHSW_MIB_TX_MULT },
-+ { "rx_unicast", GEN_STAT(mib.rx_unicast), ETHSW_MIB_TX_MULT },
-+ { "rx_pause", GEN_STAT(mib.rx_pause), ETHSW_MIB_TX_PAUSE },
-+ { "rx_dropped", GEN_STAT(mib.rx_drop), ETHSW_MIB_TX_DROP_PKTS },
-+
-+};
-+
-+#define BCM_ENETSW_STATS_LEN \
-+ (sizeof(bcm_enetsw_gstrings_stats) / sizeof(struct bcm_enet_stats))
-+
-+static void bcm_enetsw_get_strings(struct net_device *netdev,
-+ u32 stringset, u8 *data)
-+{
-+ int i;
-+
-+ switch (stringset) {
-+ case ETH_SS_STATS:
-+ for (i = 0; i < BCM_ENETSW_STATS_LEN; i++) {
-+ memcpy(data + i * ETH_GSTRING_LEN,
-+ bcm_enetsw_gstrings_stats[i].stat_string,
-+ ETH_GSTRING_LEN);
-+ }
-+ break;
-+ }
-+}
-+
-+static int bcm_enetsw_get_sset_count(struct net_device *netdev,
-+ int string_set)
-+{
-+ switch (string_set) {
-+ case ETH_SS_STATS:
-+ return BCM_ENETSW_STATS_LEN;
-+ default:
-+ return -EINVAL;
-+ }
-+}
-+
-+static void bcm_enetsw_get_drvinfo(struct net_device *netdev,
-+ struct ethtool_drvinfo *drvinfo)
-+{
-+ strncpy(drvinfo->driver, bcm_enet_driver_name, 32);
-+ strncpy(drvinfo->version, bcm_enet_driver_version, 32);
-+ strncpy(drvinfo->fw_version, "N/A", 32);
-+ strncpy(drvinfo->bus_info, "bcm63xx", 32);
-+ drvinfo->n_stats = BCM_ENETSW_STATS_LEN;
-+}
-+
-+static void bcm_enetsw_get_ethtool_stats(struct net_device *netdev,
-+ struct ethtool_stats *stats,
-+ u64 *data)
-+{
-+ struct bcm_enet_priv *priv;
-+ int i;
-+
-+ priv = netdev_priv(netdev);
-+
-+ for (i = 0; i < BCM_ENETSW_STATS_LEN; i++) {
-+ const struct bcm_enet_stats *s;
-+ u32 lo, hi;
-+ char *p;
-+ int reg;
-+
-+ s = &bcm_enetsw_gstrings_stats[i];
-+
-+ reg = s->mib_reg;
-+ if (reg == -1)
-+ continue;
-+
-+ lo = enetsw_readl(priv, ENETSW_MIB_REG(reg));
-+ p = (char *)priv + s->stat_offset;
-+
-+ if (s->sizeof_stat == sizeof(u64)) {
-+ hi = enetsw_readl(priv, ENETSW_MIB_REG(reg + 1));
-+ *(u64 *)p = ((u64)hi << 32 | lo);
-+ } else {
-+ *(u32 *)p = lo;
-+ }
-+ }
-+
-+ for (i = 0; i < BCM_ENETSW_STATS_LEN; i++) {
-+ const struct bcm_enet_stats *s;
-+ char *p;
-+
-+ s = &bcm_enetsw_gstrings_stats[i];
-+
-+ if (s->mib_reg == -1)
-+ p = (char *)&netdev->stats + s->stat_offset;
-+ else
-+ p = (char *)priv + s->stat_offset;
-+
-+ data[i] = (s->sizeof_stat == sizeof(u64)) ?
-+ *(u64 *)p : *(u32 *)p;
-+ }
-+}
-+
-+static void bcm_enetsw_get_ringparam(struct net_device *dev,
-+ struct ethtool_ringparam *ering)
-+{
-+ struct bcm_enet_priv *priv;
-+
-+ priv = netdev_priv(dev);
-+
-+ /* rx/tx ring is actually only limited by memory */
-+ ering->rx_max_pending = 8192;
-+ ering->tx_max_pending = 8192;
-+ ering->rx_mini_max_pending = 0;
-+ ering->rx_jumbo_max_pending = 0;
-+ ering->rx_pending = priv->rx_ring_size;
-+ ering->tx_pending = priv->tx_ring_size;
-+}
-+
-+static int bcm_enetsw_set_ringparam(struct net_device *dev,
-+ struct ethtool_ringparam *ering)
-+{
-+ struct bcm_enet_priv *priv;
-+ int was_running;
-+
-+ priv = netdev_priv(dev);
-+
-+ was_running = 0;
-+ if (netif_running(dev)) {
-+ bcm_enetsw_stop(dev);
-+ was_running = 1;
-+ }
-+
-+ priv->rx_ring_size = ering->rx_pending;
-+ priv->tx_ring_size = ering->tx_pending;
-+
-+ if (was_running) {
-+ int err;
-+
-+ err = bcm_enetsw_open(dev);
-+ if (err)
-+ dev_close(dev);
-+ }
-+ return 0;
-+}
-+
-+static struct ethtool_ops bcm_enetsw_ethtool_ops = {
-+ .get_strings = bcm_enetsw_get_strings,
-+ .get_sset_count = bcm_enetsw_get_sset_count,
-+ .get_ethtool_stats = bcm_enetsw_get_ethtool_stats,
-+ .get_drvinfo = bcm_enetsw_get_drvinfo,
-+ .get_ringparam = bcm_enetsw_get_ringparam,
-+ .set_ringparam = bcm_enetsw_set_ringparam,
-+};
-+
-+/*
-+ * allocate netdevice, request register memory and register device.
-+ */
-+static int bcm_enetsw_probe(struct platform_device *pdev)
-+{
-+ struct bcm_enet_priv *priv;
-+ struct net_device *dev;
-+ struct bcm63xx_enetsw_platform_data *pd;
-+ struct resource *res_mem;
-+ int ret, irq_rx, irq_tx;
-+
-+ /* stop if shared driver failed, assume driver->probe will be
-+ * called in the same order we register devices (correct ?) */
-+ if (!bcm_enet_shared_base[0])
-+ return -ENODEV;
-+
-+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ irq_rx = platform_get_irq(pdev, 0);
-+ irq_tx = platform_get_irq(pdev, 1);
-+ if (!res_mem || irq_rx < 0)
-+ return -ENODEV;
-+
-+ ret = 0;
-+ dev = alloc_etherdev(sizeof(*priv));
-+ if (!dev)
-+ return -ENOMEM;
-+ priv = netdev_priv(dev);
-+ memset(priv, 0, sizeof(*priv));
-+
-+ /* initialize default and fetch platform data */
-+ priv->enet_is_sw = true;
-+ priv->irq_rx = irq_rx;
-+ priv->irq_tx = irq_tx;
-+ priv->rx_ring_size = BCMENET_DEF_RX_DESC;
-+ priv->tx_ring_size = BCMENET_DEF_TX_DESC;
-+ priv->dma_maxburst = BCMENETSW_DMA_MAXBURST;
-+
-+ pd = pdev->dev.platform_data;
-+ if (pd) {
-+ memcpy(dev->dev_addr, pd->mac_addr, ETH_ALEN);
-+ memcpy(priv->used_ports, pd->used_ports,
-+ sizeof (pd->used_ports));
-+ priv->num_ports = pd->num_ports;
-+ }
-+
-+ ret = compute_hw_mtu(priv, dev->mtu);
-+ if (ret)
-+ goto out;
-+
-+ if (!request_mem_region(res_mem->start, resource_size(res_mem),
-+ "bcm63xx_enetsw")) {
-+ ret = -EBUSY;
-+ goto out;
-+ }
-+
-+ priv->base = ioremap(res_mem->start, resource_size(res_mem));
-+ if (priv->base == NULL) {
-+ ret = -ENOMEM;
-+ goto out_release_mem;
-+ }
-+
-+ priv->mac_clk = clk_get(&pdev->dev, "enetsw");
-+ if (IS_ERR(priv->mac_clk)) {
-+ ret = PTR_ERR(priv->mac_clk);
-+ goto out_unmap;
-+ }
-+ clk_enable(priv->mac_clk);
-+
-+ priv->rx_chan = 0;
-+ priv->tx_chan = 1;
-+ spin_lock_init(&priv->rx_lock);
-+
-+ /* init rx timeout (used for oom) */
-+ init_timer(&priv->rx_timeout);
-+ priv->rx_timeout.function = bcm_enet_refill_rx_timer;
-+ priv->rx_timeout.data = (unsigned long)dev;
-+
-+ /* register netdevice */
-+ dev->netdev_ops = &bcm_enetsw_ops;
-+ netif_napi_add(dev, &priv->napi, bcm_enet_poll, 16);
-+ SET_ETHTOOL_OPS(dev, &bcm_enetsw_ethtool_ops);
-+ SET_NETDEV_DEV(dev, &pdev->dev);
-+
-+ spin_lock_init(&priv->enetsw_mdio_lock);
-+
-+ ret = register_netdev(dev);
-+ if (ret)
-+ goto out_put_clk;
-+
-+ netif_carrier_off(dev);
-+ platform_set_drvdata(pdev, dev);
-+ priv->pdev = pdev;
-+ priv->net_dev = dev;
-+
-+ return 0;
-+
-+out_put_clk:
-+ clk_put(priv->mac_clk);
-+
-+out_unmap:
-+ iounmap(priv->base);
-+
-+out_release_mem:
-+ release_mem_region(res_mem->start, resource_size(res_mem));
-+out:
-+ free_netdev(dev);
-+ return ret;
-+}
-+
-+
-+/*
-+ * exit func, stops hardware and unregisters netdevice
-+ */
-+static int bcm_enetsw_remove(struct platform_device *pdev)
-+{
-+ struct bcm_enet_priv *priv;
-+ struct net_device *dev;
-+ struct resource *res;
-+
-+ /* stop netdevice */
-+ dev = platform_get_drvdata(pdev);
-+ priv = netdev_priv(dev);
-+ unregister_netdev(dev);
-+
-+ /* release device resources */
-+ iounmap(priv->base);
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ release_mem_region(res->start, resource_size(res));
-+
-+ platform_set_drvdata(pdev, NULL);
-+ free_netdev(dev);
-+ return 0;
-+}
-+
-+struct platform_driver bcm63xx_enetsw_driver = {
-+ .probe = bcm_enetsw_probe,
-+ .remove = bcm_enetsw_remove,
-+ .driver = {
-+ .name = "bcm63xx_enetsw",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+/*
-+ * reserve & remap memory space shared between all macs
-+ */
-+static int bcm_enet_shared_probe(struct platform_device *pdev)
-+{
-+ struct resource *res;
-+ void __iomem *p[3];
-+ unsigned int i;
-+
-+ memset(bcm_enet_shared_base, 0, sizeof(bcm_enet_shared_base));
-+
-+ for (i = 0; i < 3; i++) {
-+ res = platform_get_resource(pdev, IORESOURCE_MEM, i);
-+ if (!res)
-+ return -EINVAL;
-+
-+ p[i] = devm_request_and_ioremap(&pdev->dev, res);
-+ if (!p[i])
-+ return -ENOMEM;
-+ }
-+
-+ memcpy(bcm_enet_shared_base, p, sizeof(bcm_enet_shared_base));
-+
-+ return 0;
-+}
-+
-+static int bcm_enet_shared_remove(struct platform_device *pdev)
-+{
-+ return 0;
-+}
-+
-+/*
-+ * this "shared" driver is needed because both macs share a single
-+ * address space
-+ */
-+struct platform_driver bcm63xx_enet_shared_driver = {
-+ .probe = bcm_enet_shared_probe,
-+ .remove = bcm_enet_shared_remove,
-+ .driver = {
-+ .name = "bcm63xx_enet_shared",
-+ .owner = THIS_MODULE,
-+ },
-+};
-+
-+/*
-+ * entry point
-+ */
-+static int __init bcm_enet_init(void)
-+{
-+ int ret;
-+
-+ ret = platform_driver_register(&bcm63xx_enet_shared_driver);
-+ if (ret)
-+ return ret;
-+
-+ ret = platform_driver_register(&bcm63xx_enet_driver);
-+ if (ret)
-+ platform_driver_unregister(&bcm63xx_enet_shared_driver);
-+
-+ ret = platform_driver_register(&bcm63xx_enetsw_driver);
-+ if (ret) {
-+ platform_driver_unregister(&bcm63xx_enet_driver);
-+ platform_driver_unregister(&bcm63xx_enet_shared_driver);
-+ }
-
- return ret;
- }
-@@ -1966,6 +2895,7 @@ static int __init bcm_enet_init(void)
- static void __exit bcm_enet_exit(void)
- {
- platform_driver_unregister(&bcm63xx_enet_driver);
-+ platform_driver_unregister(&bcm63xx_enetsw_driver);
- platform_driver_unregister(&bcm63xx_enet_shared_driver);
- }
-
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h
-@@ -18,6 +18,7 @@
-
- /* maximum burst len for dma (4 bytes unit) */
- #define BCMENET_DMA_MAXBURST 16
-+#define BCMENETSW_DMA_MAXBURST 8
-
- /* tx transmit threshold (4 bytes unit), fifo is 256 bytes, the value
- * must be low enough so that a DMA transfer of above burst length can
-@@ -84,11 +85,60 @@
- #define ETH_MIB_RX_CNTRL 54
-
-
-+/*
-+ * SW MIB Counters register definitions
-+*/
-+#define ETHSW_MIB_TX_ALL_OCT 0
-+#define ETHSW_MIB_TX_DROP_PKTS 2
-+#define ETHSW_MIB_TX_QOS_PKTS 3
-+#define ETHSW_MIB_TX_BRDCAST 4
-+#define ETHSW_MIB_TX_MULT 5
-+#define ETHSW_MIB_TX_UNI 6
-+#define ETHSW_MIB_TX_COL 7
-+#define ETHSW_MIB_TX_1_COL 8
-+#define ETHSW_MIB_TX_M_COL 9
-+#define ETHSW_MIB_TX_DEF 10
-+#define ETHSW_MIB_TX_LATE 11
-+#define ETHSW_MIB_TX_EX_COL 12
-+#define ETHSW_MIB_TX_PAUSE 14
-+#define ETHSW_MIB_TX_QOS_OCT 15
-+
-+#define ETHSW_MIB_RX_ALL_OCT 17
-+#define ETHSW_MIB_RX_UND 19
-+#define ETHSW_MIB_RX_PAUSE 20
-+#define ETHSW_MIB_RX_64 21
-+#define ETHSW_MIB_RX_65_127 22
-+#define ETHSW_MIB_RX_128_255 23
-+#define ETHSW_MIB_RX_256_511 24
-+#define ETHSW_MIB_RX_512_1023 25
-+#define ETHSW_MIB_RX_1024_1522 26
-+#define ETHSW_MIB_RX_OVR 27
-+#define ETHSW_MIB_RX_JAB 28
-+#define ETHSW_MIB_RX_ALIGN 29
-+#define ETHSW_MIB_RX_CRC 30
-+#define ETHSW_MIB_RX_GD_OCT 31
-+#define ETHSW_MIB_RX_DROP 33
-+#define ETHSW_MIB_RX_UNI 34
-+#define ETHSW_MIB_RX_MULT 35
-+#define ETHSW_MIB_RX_BRDCAST 36
-+#define ETHSW_MIB_RX_SA_CHANGE 37
-+#define ETHSW_MIB_RX_FRAG 38
-+#define ETHSW_MIB_RX_OVR_DISC 39
-+#define ETHSW_MIB_RX_SYM 40
-+#define ETHSW_MIB_RX_QOS_PKTS 41
-+#define ETHSW_MIB_RX_QOS_OCT 42
-+#define ETHSW_MIB_RX_1523_2047 44
-+#define ETHSW_MIB_RX_2048_4095 45
-+#define ETHSW_MIB_RX_4096_8191 46
-+#define ETHSW_MIB_RX_8192_9728 47
-+
-+
- struct bcm_enet_mib_counters {
- u64 tx_gd_octets;
- u32 tx_gd_pkts;
- u32 tx_all_octets;
- u32 tx_all_pkts;
-+ u32 tx_unicast;
- u32 tx_brdcast;
- u32 tx_mult;
- u32 tx_64;
-@@ -97,7 +147,12 @@ struct bcm_enet_mib_counters {
- u32 tx_256_511;
- u32 tx_512_1023;
- u32 tx_1024_max;
-+ u32 tx_1523_2047;
-+ u32 tx_2048_4095;
-+ u32 tx_4096_8191;
-+ u32 tx_8192_9728;
- u32 tx_jab;
-+ u32 tx_drop;
- u32 tx_ovr;
- u32 tx_frag;
- u32 tx_underrun;
-@@ -114,6 +169,7 @@ struct bcm_enet_mib_counters {
- u32 rx_all_octets;
- u32 rx_all_pkts;
- u32 rx_brdcast;
-+ u32 rx_unicast;
- u32 rx_mult;
- u32 rx_64;
- u32 rx_65_127;
-@@ -197,6 +253,9 @@ struct bcm_enet_priv {
- /* number of dma desc in tx ring */
- int tx_ring_size;
-
-+ /* maximum dma burst size */
-+ int dma_maxburst;
-+
- /* cpu view of rx dma ring */
- struct bcm_enet_desc *tx_desc_cpu;
-
-@@ -269,6 +328,22 @@ struct bcm_enet_priv {
-
- /* maximum hardware transmit/receive size */
- unsigned int hw_mtu;
-+
-+ bool enet_is_sw;
-+
-+ /* port mapping for switch devices */
-+ int num_ports;
-+ struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT];
-+ int sw_port_link[ENETSW_MAX_PORT];
-+
-+ /* used to poll switch port state */
-+ struct timer_list swphy_poll;
-+ spinlock_t enetsw_mdio_lock;
- };
-
-+static inline int bcm_enet_port_is_rgmii(int portid)
-+{
-+ return portid >= ENETSW_RGMII_PORT0;
-+}
-+
- #endif /* ! BCM63XX_ENET_H_ */
+++ /dev/null
-From d8237d704fc25eb2fc25ef4403608b78c6a6d4be Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Sun, 15 Jul 2012 20:08:57 +0200
-Subject: [PATCH 54/81] bcm63xx_enet: enable rgmii clock on external ports
-
----
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 13 +++++++++++++
- drivers/net/ethernet/broadcom/bcm63xx_enet.c | 12 ++++++++++++
- 2 files changed, 25 insertions(+), 0 deletions(-)
-
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -861,6 +861,19 @@
- #define ENETSW_PORTOV_FDX_MASK (1 << 1)
- #define ENETSW_PORTOV_LINKUP_MASK (1 << 0)
-
-+/* Port RGMII control register */
-+#define ENETSW_RGMII_CTRL_REG(x) (0x60 + (x))
-+#define ENETSW_RGMII_CTRL_GMII_CLK_EN (1 << 7)
-+#define ENETSW_RGMII_CTRL_MII_OVERRIDE_EN (1 << 6)
-+#define ENETSW_RGMII_CTRL_MII_MODE_MASK (3 << 4)
-+#define ENETSW_RGMII_CTRL_RGMII_MODE (0 << 4)
-+#define ENETSW_RGMII_CTRL_MII_MODE (1 << 4)
-+#define ENETSW_RGMII_CTRL_RVMII_MODE (2 << 4)
-+#define ENETSW_RGMII_CTRL_TIMING_SEL_EN (1 << 0)
-+
-+/* Port RGMII timing register */
-+#define ENETSW_RGMII_TIMING_REG(x) (0x68 + (x))
-+
- /* MDIO control register */
- #define ENETSW_MDIOC_REG (0xb0)
- #define ENETSW_MDIOC_EXT_MASK (1 << 16)
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-@@ -2201,6 +2201,18 @@ static int bcm_enetsw_open(struct net_de
- priv->sw_port_link[i] = 0;
- }
-
-+ /* enable external ports */
-+ for (i = ENETSW_RGMII_PORT0; i < priv->num_ports; i++) {
-+ u8 rgmii_ctrl;
-+
-+ if (!priv->used_ports[i].used)
-+ continue;
-+
-+ rgmii_ctrl = enetsw_readb(priv, ENETSW_RGMII_CTRL_REG(i));
-+ rgmii_ctrl |= ENETSW_RGMII_CTRL_GMII_CLK_EN;
-+ enetsw_writeb(priv, rgmii_ctrl, ENETSW_RGMII_CTRL_REG(i));
-+ }
-+
- /* reset mib */
- val = enetsw_readb(priv, ENETSW_GMCR_REG);
- val |= ENETSW_GMCR_RST_MIB_MASK;
+++ /dev/null
-From 261ee140e75615351128eee497e6bbd76686784b Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Sat, 12 Nov 2011 12:18:26 +0100
-Subject: [PATCH 51/72] MIPS: BCM63XX: add HS SPI platform device and register
- it
-
-Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
----
- arch/mips/bcm63xx/Makefile | 4 +-
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 2 +
- arch/mips/bcm63xx/dev-hsspi.c | 57 ++++++++++++++++++++
- .../include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h | 20 +++++++
- 4 files changed, 81 insertions(+), 2 deletions(-)
- create mode 100644 arch/mips/bcm63xx/dev-hsspi.c
- create mode 100644 arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
-
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -1,7 +1,8 @@
- obj-y += clk.o cpu.o cs.o gpio.o irq.o nvram.o prom.o reset.o \
- setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
-- dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o dev-wdt.o \
-- dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o usb-common.o
-+ dev-hsspi.o dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o \
-+ dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \
-+ usb-common.o
- obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
-
- obj-y += boards/
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -26,6 +26,7 @@
- #include <bcm63xx_dev_enet.h>
- #include <bcm63xx_dev_dsp.h>
- #include <bcm63xx_dev_flash.h>
-+#include <bcm63xx_dev_hsspi.h>
- #include <bcm63xx_dev_pcmcia.h>
- #include <bcm63xx_dev_spi.h>
- #include <bcm63xx_dev_usb_ehci.h>
-@@ -952,6 +953,7 @@ int __init board_register_devices(void)
- pr_err(PFX "failed to register fallback SPROM\n");
- }
- #endif
-+ bcm63xx_hsspi_register();
-
- bcm63xx_spi_register();
-
---- /dev/null
-+++ b/arch/mips/bcm63xx/dev-hsspi.c
-@@ -0,0 +1,60 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/platform_device.h>
-+
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_dev_hsspi.h>
-+#include <bcm63xx_regs.h>
-+
-+static struct resource spi_resources[] = {
-+ {
-+ .start = -1, /* filled at runtime */
-+ .end = -1, /* filled at runtime */
-+ .flags = IORESOURCE_MEM,
-+ },
-+ {
-+ .start = -1, /* filled at runtime */
-+ .flags = IORESOURCE_IRQ,
-+ },
-+};
-+
-+static struct bcm63xx_hsspi_pdata spi_pdata = {
-+ .bus_num = 1,
-+};
-+
-+static struct platform_device bcm63xx_hsspi_device = {
-+ .name = "bcm63xx-hsspi",
-+ .id = 0,
-+ .num_resources = ARRAY_SIZE(spi_resources),
-+ .resource = spi_resources,
-+ .dev = {
-+ .platform_data = &spi_pdata,
-+ },
-+};
-+
-+int __init bcm63xx_hsspi_register(void)
-+{
-+
-+ if (!BCMCPU_IS_6328() && !BCMCPU_IS_6362())
-+ return -ENODEV;
-+
-+ spi_resources[0].start = bcm63xx_regset_address(RSET_HSSPI);
-+ spi_resources[0].end = spi_resources[0].start;
-+ spi_resources[0].end += RSET_HSSPI_SIZE - 1;
-+ spi_resources[1].start = bcm63xx_get_irq_number(IRQ_HSSPI);
-+
-+ if (BCMCPU_IS_6328())
-+ spi_pdata.speed_hz = HSSPI_PLL_HZ_6328;
-+ else if (BCMCPU_IS_6362())
-+ spi_pdata.speed_hz = HSSPI_PLL_HZ_6362;
-+
-+ return platform_device_register(&bcm63xx_hsspi_device);
-+}
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
-@@ -0,0 +1,21 @@
-+#ifndef BCM63XX_DEV_HSSPI_H
-+#define BCM63XX_DEV_HSSPI_H
-+
-+#include <linux/types.h>
-+#include <bcm63xx_io.h>
-+#include <bcm63xx_regs.h>
-+
-+int __init bcm63xx_hsspi_register(void);
-+
-+struct bcm63xx_hsspi_pdata {
-+ int bus_num;
-+ u32 speed_hz;
-+};
-+
-+#define bcm_hsspi_readl(o) bcm_rset_readl(RSET_HSSPI, (o))
-+#define bcm_hsspi_writel(v, o) bcm_rset_writel(RSET_HSSPI, (v), (o))
-+
-+#define HSSPI_PLL_HZ_6328 133333333
-+#define HSSPI_PLL_HZ_6362 400000000
-+
-+#endif /* BCM63XX_DEV_HSSPI_H */
+++ /dev/null
-From 4b27423676485d05bcd6fc6f3809164fb8f9d22d Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Sat, 12 Nov 2011 12:19:55 +0100
-Subject: [PATCH 30/60] SPI: MIPS: BCM63XX: Add HSSPI driver
-
-Add a driver for the High Speed SPI controller found on newer BCM63XX SoCs.
-
-Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
----
- .../include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h | 2 +
- drivers/spi/Kconfig | 7 +
- drivers/spi/Makefile | 1 +
- drivers/spi/spi-bcm63xx-hsspi.c | 427 ++++++++++++++++++++
- 4 files changed, 437 insertions(+), 0 deletions(-)
- create mode 100644 drivers/spi/spi-bcm63xx-hsspi.c
-
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_hsspi.h
-@@ -18,4 +18,6 @@ struct bcm63xx_hsspi_pdata {
- #define HSSPI_PLL_HZ_6328 133333333
- #define HSSPI_PLL_HZ_6362 400000000
-
-+#define HSSPI_BUFFER_LEN 512
-+
- #endif /* BCM63XX_DEV_HSSPI_H */
---- a/drivers/spi/Kconfig
-+++ b/drivers/spi/Kconfig
-@@ -100,6 +100,13 @@ config SPI_BCM63XX
- help
- Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
-
-+config SPI_BCM63XX_HSSPI
-+ tristate "Broadcom BCM63XX HS SPI controller driver"
-+ depends on BCM63XX
-+ help
-+ This enables support for the High Speed SPI controller present on
-+ newer Broadcom BCM63XX SoCs.
-+
- config SPI_BITBANG
- tristate "Utilities for Bitbanging SPI masters"
- help
---- a/drivers/spi/Makefile
-+++ b/drivers/spi/Makefile
-@@ -15,6 +15,7 @@ obj-$(CONFIG_SPI_ATMEL) += spi-atmel.o
- obj-$(CONFIG_SPI_ATH79) += spi-ath79.o
- obj-$(CONFIG_SPI_AU1550) += spi-au1550.o
- obj-$(CONFIG_SPI_BCM63XX) += spi-bcm63xx.o
-+obj-$(CONFIG_SPI_BCM63XX_HSSPI) += spi-bcm63xx-hsspi.o
- obj-$(CONFIG_SPI_BFIN5XX) += spi-bfin5xx.o
- obj-$(CONFIG_SPI_BFIN_SPORT) += spi-bfin-sport.o
- obj-$(CONFIG_SPI_BITBANG) += spi-bitbang.o
---- /dev/null
-+++ b/drivers/spi/spi-bcm63xx-hsspi.c
-@@ -0,0 +1,427 @@
-+/*
-+ * Broadcom BCM63XX High Speed SPI Controller driver
-+ *
-+ * Copyright 2000-2010 Broadcom Corporation
-+ * Copyright 2012 Jonas Gorski <jonas.gorski@gmail.com>
-+ *
-+ * Licensed under the GNU/GPL. See COPYING for details.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/io.h>
-+#include <linux/clk.h>
-+#include <linux/module.h>
-+#include <linux/platform_device.h>
-+#include <linux/delay.h>
-+#include <linux/dma-mapping.h>
-+#include <linux/err.h>
-+#include <linux/interrupt.h>
-+#include <linux/spi/spi.h>
-+#include <linux/workqueue.h>
-+
-+#include <bcm63xx_regs.h>
-+#include <bcm63xx_dev_hsspi.h>
-+
-+#define HSSPI_OP_CODE_SHIFT 13
-+#define HSSPI_OP_SLEEP (0 << HSSPI_OP_CODE_SHIFT)
-+#define HSSPI_OP_READ_WRITE (1 << HSSPI_OP_CODE_SHIFT)
-+#define HSSPI_OP_WRITE (2 << HSSPI_OP_CODE_SHIFT)
-+#define HSSPI_OP_READ (3 << HSSPI_OP_CODE_SHIFT)
-+
-+#define HSSPI_MAX_PREPEND_LEN 15
-+
-+#define HSSPI_MAX_SYNC_CLOCK 30000000
-+
-+struct bcm63xx_hsspi {
-+ struct completion done;
-+ struct spi_transfer *curr_trans;
-+
-+ struct platform_device *pdev;
-+ struct clk *clk;
-+ void __iomem *regs;
-+ u8 __iomem *fifo;
-+
-+ u32 speed_hz;
-+ int irq;
-+};
-+
-+static void bcm63xx_hsspi_set_clk(struct bcm63xx_hsspi *bs, int hz,
-+ int profile)
-+{
-+ u32 reg;
-+
-+ reg = DIV_ROUND_UP(2048, DIV_ROUND_UP(bs->speed_hz, hz));
-+ bcm_hsspi_writel(CLK_CTRL_ACCUM_RST_ON_LOOP | reg,
-+ HSSPI_PROFILE_CLK_CTRL_REG(profile));
-+
-+ reg = bcm_hsspi_readl(HSSPI_PROFILE_SIGNAL_CTRL_REG(profile));
-+ if (hz > HSSPI_MAX_SYNC_CLOCK)
-+ reg |= SIGNAL_CTRL_ASYNC_INPUT_PATH;
-+ else
-+ reg &= ~SIGNAL_CTRL_ASYNC_INPUT_PATH;
-+ bcm_hsspi_writel(reg, HSSPI_PROFILE_SIGNAL_CTRL_REG(profile));
-+}
-+
-+static int bcm63xx_hsspi_do_txrx(struct spi_device *spi,
-+ struct spi_transfer *t1,
-+ struct spi_transfer *t2)
-+{
-+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master);
-+ u8 chip_select = spi->chip_select;
-+ u16 opcode = 0;
-+ int len, prepend_size = 0;
-+
-+ init_completion(&bs->done);
-+
-+ bs->curr_trans = t2 ? t2 : t1;
-+ bcm63xx_hsspi_set_clk(bs, bs->curr_trans->speed_hz, chip_select);
-+
-+ if (t2 && !t2->tx_buf)
-+ prepend_size = t1->len;
-+
-+ bcm_hsspi_writel(prepend_size << MODE_CTRL_PREPENDBYTE_CNT_SHIFT |
-+ 2 << MODE_CTRL_MULTIDATA_WR_STRT_SHIFT |
-+ 2 << MODE_CTRL_MULTIDATA_RD_STRT_SHIFT | 0xff,
-+ HSSPI_PROFILE_MODE_CTRL_REG(chip_select));
-+
-+ if (t1->rx_buf && t1->tx_buf)
-+ opcode = HSSPI_OP_READ_WRITE;
-+ else if (t1->rx_buf || (t2 && t2->rx_buf))
-+ opcode = HSSPI_OP_READ;
-+ else if (t1->tx_buf)
-+ opcode = HSSPI_OP_WRITE;
-+
-+ if (opcode == HSSPI_OP_READ && t2)
-+ len = t2->len;
-+ else
-+ len = t1->len;
-+
-+ if (t1->tx_buf) {
-+ memcpy_toio(bs->fifo + 2, t1->tx_buf, t1->len);
-+ if (t2 && t2->tx_buf) {
-+ memcpy_toio(bs->fifo + 2 + t1->len,
-+ t2->tx_buf, t2->len);
-+ len += t2->len;
-+ }
-+ }
-+
-+ opcode |= len;
-+ memcpy_toio(bs->fifo, &opcode, sizeof(opcode));
-+
-+ /* enable interrupt */
-+ bcm_hsspi_writel(HSSPI_PING0_CMD_DONE, HSSPI_INT_MASK_REG);
-+
-+ /* start the transfer */
-+ bcm_hsspi_writel(chip_select << PINGPONG_CMD_SS_SHIFT |
-+ chip_select << PINGPONG_CMD_PROFILE_SHIFT |
-+ PINGPONG_COMMAND_START_NOW,
-+ HSSPI_PINGPONG_COMMAND_REG(0));
-+
-+ if (wait_for_completion_timeout(&bs->done, HZ) == 0) {
-+ dev_err(&bs->pdev->dev, "transfer timed out!\n");
-+ return -ETIMEDOUT;
-+ }
-+
-+ return t1->len + (t2 ? t2->len : 0);
-+}
-+
-+static int bcm63xx_hsspi_setup(struct spi_device *spi)
-+{
-+ u32 reg;
-+
-+ if (spi->bits_per_word != 8)
-+ return -EINVAL;
-+
-+ if (spi->max_speed_hz == 0)
-+ return -EINVAL;
-+
-+ reg = bcm_hsspi_readl(HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select));
-+ reg &= ~(SIGNAL_CTRL_LAUNCH_RISING | SIGNAL_CTRL_LATCH_RISING);
-+ if (spi->mode & SPI_CPHA)
-+ reg |= SIGNAL_CTRL_LAUNCH_RISING;
-+ else
-+ reg |= SIGNAL_CTRL_LATCH_RISING;
-+ bcm_hsspi_writel(reg, HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select));
-+
-+ return 0;
-+}
-+
-+static int bcm63xx_hsspi_transfer_one(struct spi_master *master,
-+ struct spi_message *msg)
-+{
-+ struct spi_transfer *t, *prev = NULL;
-+ struct spi_device *spi = msg->spi;
-+ u32 reg;
-+ int ret = -EINVAL;
-+ int len = 0;
-+
-+ /* check if we are able to make these transfers */
-+ list_for_each_entry(t, &msg->transfers, transfer_list) {
-+ if (!t->tx_buf && !t->rx_buf)
-+ goto out;
-+
-+ if (t->speed_hz == 0)
-+ t->speed_hz = spi->max_speed_hz;
-+
-+ if (t->speed_hz > spi->max_speed_hz)
-+ goto out;
-+
-+ if (t->len > HSSPI_BUFFER_LEN)
-+ goto out;
-+
-+ /*
-+ * This controller does not support keeping the chip select
-+ * active between transfers.
-+ * This logic currently supports combining:
-+ * write then read with no cs_change (e.g. m25p80 RDSR)
-+ * write then write with no cs_change (e.g. m25p80 PP)
-+ */
-+ if (prev && prev->tx_buf && !prev->cs_change && !t->cs_change) {
-+ /*
-+ * reject if we have to combine two tx transfers and
-+ * their combined length is bigger than the buffer
-+ */
-+ if (prev->tx_buf && t->tx_buf &&
-+ (prev->len + t->len) > HSSPI_BUFFER_LEN)
-+ goto out;
-+ /*
-+ * reject if we need write more than 15 bytes in read
-+ * then write.
-+ */
-+ if (prev->tx_buf && t->rx_buf &&
-+ prev->len > HSSPI_MAX_PREPEND_LEN)
-+ goto out;
-+ }
-+
-+ }
-+
-+ /* setup clock polarity */
-+ reg = bcm_hsspi_readl(HSSPI_GLOBAL_CTRL_REG);
-+ reg &= ~GLOBAL_CTRL_CLK_POLARITY;
-+ if (spi->mode & SPI_CPOL)
-+ reg |= GLOBAL_CTRL_CLK_POLARITY;
-+ bcm_hsspi_writel(reg, HSSPI_GLOBAL_CTRL_REG);
-+
-+ list_for_each_entry(t, &msg->transfers, transfer_list) {
-+ if (prev && prev->tx_buf && !prev->cs_change && !t->cs_change) {
-+ /* combine write with following transfer */
-+ ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, t);
-+ if (ret < 0)
-+ goto out;
-+
-+ len += ret;
-+ prev = NULL;
-+ continue;
-+ }
-+
-+ /* write the previous pending transfer */
-+ if (prev != NULL) {
-+ ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, NULL);
-+ if (ret < 0)
-+ goto out;
-+
-+ len += ret;
-+ }
-+
-+ prev = t;
-+ }
-+
-+ /* do last pending transfer */
-+ if (prev != NULL) {
-+ ret = bcm63xx_hsspi_do_txrx(msg->spi, prev, NULL);
-+ if (ret < 0)
-+ goto out;
-+ len += ret;
-+ }
-+
-+ msg->actual_length = len;
-+ ret = 0;
-+out:
-+ msg->status = ret;
-+ spi_finalize_current_message(master);
-+ return 0;
-+}
-+
-+static irqreturn_t bcm63xx_hsspi_interrupt(int irq, void *dev_id)
-+{
-+ struct spi_master *master = (struct spi_master *)dev_id;
-+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
-+
-+ if (bcm_hsspi_readl(HSSPI_INT_STATUS_MASKED_REG) == 0)
-+ return IRQ_NONE;
-+
-+ bcm_hsspi_writel(HSSPI_INT_CLEAR_ALL, HSSPI_INT_STATUS_REG);
-+ bcm_hsspi_writel(0, HSSPI_INT_MASK_REG);
-+
-+ if (bs->curr_trans && bs->curr_trans->rx_buf)
-+ memcpy_fromio(bs->curr_trans->rx_buf, bs->fifo,
-+ bs->curr_trans->len);
-+ complete(&bs->done);
-+
-+ return IRQ_HANDLED;
-+}
-+
-+static int bcm63xx_hsspi_probe(struct platform_device *pdev)
-+{
-+
-+ struct spi_master *master;
-+ struct bcm63xx_hsspi *bs;
-+ struct resource *res_mem;
-+ void __iomem *regs;
-+ struct device *dev = &pdev->dev;
-+ struct bcm63xx_hsspi_pdata *pdata = pdev->dev.platform_data;
-+ struct clk *clk;
-+ int irq;
-+ int ret;
-+
-+ irq = platform_get_irq(pdev, 0);
-+ if (irq < 0) {
-+ dev_err(dev, "no irq\n");
-+ return -ENXIO;
-+ }
-+
-+ res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-+ regs = devm_request_and_ioremap(dev, res_mem);
-+ if (!regs) {
-+ dev_err(dev, "unable to ioremap regs\n");
-+ return -ENXIO;
-+ }
-+
-+ clk = clk_get(dev, "hsspi");
-+
-+ if (IS_ERR(clk)) {
-+ ret = PTR_ERR(clk);
-+ goto out_release;
-+ }
-+
-+ clk_prepare_enable(clk);
-+
-+ master = spi_alloc_master(&pdev->dev, sizeof(*bs));
-+ if (!master) {
-+ ret = -ENOMEM;
-+ goto out_disable_clk;
-+ }
-+
-+ bs = spi_master_get_devdata(master);
-+ bs->pdev = pdev;
-+ bs->clk = clk;
-+ bs->regs = regs;
-+
-+ master->bus_num = pdata->bus_num;
-+ master->num_chipselect = 8;
-+ master->setup = bcm63xx_hsspi_setup;
-+ master->transfer_one_message = bcm63xx_hsspi_transfer_one;
-+ master->mode_bits = SPI_CPOL | SPI_CPHA;
-+
-+ bs->speed_hz = pdata->speed_hz;
-+ bs->fifo = (u8 __iomem *)(bs->regs + HSSPI_FIFO_REG(0));
-+
-+ platform_set_drvdata(pdev, master);
-+
-+ bs->curr_trans = NULL;
-+
-+ /* Initialize the hardware */
-+ bcm_hsspi_writel(0, HSSPI_INT_MASK_REG);
-+
-+ /* clean up any pending interrupts */
-+ bcm_hsspi_writel(HSSPI_INT_CLEAR_ALL, HSSPI_INT_STATUS_REG);
-+
-+ bcm_hsspi_writel(bcm_hsspi_readl(HSSPI_GLOBAL_CTRL_REG) |
-+ GLOBAL_CTRL_CLK_GATE_SSOFF,
-+ HSSPI_GLOBAL_CTRL_REG);
-+
-+ ret = devm_request_irq(dev, irq, bcm63xx_hsspi_interrupt, IRQF_SHARED,
-+ pdev->name, master);
-+
-+ if (ret)
-+ goto out_put_master;
-+
-+ /* register and we are done */
-+ ret = spi_register_master(master);
-+ if (ret)
-+ goto out_free_irq;
-+
-+ return 0;
-+
-+out_free_irq:
-+ devm_free_irq(dev, bs->irq, master);
-+out_put_master:
-+ spi_master_put(master);
-+out_disable_clk:
-+ clk_disable_unprepare(clk);
-+ clk_put(clk);
-+out_release:
-+ devm_ioremap_release(dev, regs);
-+
-+ return ret;
-+}
-+
-+
-+static int __exit bcm63xx_hsspi_remove(struct platform_device *pdev)
-+{
-+ struct spi_master *master = platform_get_drvdata(pdev);
-+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
-+
-+ spi_unregister_master(master);
-+
-+ /* reset the hardware and block queue progress */
-+ bcm_hsspi_writel(0, HSSPI_INT_MASK_REG);
-+ clk_disable_unprepare(bs->clk);
-+ clk_put(bs->clk);
-+
-+ return 0;
-+}
-+
-+#ifdef CONFIG_PM
-+static int bcm63xx_hsspi_suspend(struct platform_device *pdev,
-+ pm_message_t mesg)
-+{
-+ struct spi_master *master = platform_get_drvdata(pdev);
-+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
-+
-+ spi_master_suspend(master);
-+ clk_disable(bs->clk);
-+
-+ return 0;
-+}
-+
-+static int bcm63xx_hsspi_resume(struct platform_device *pdev)
-+{
-+ struct spi_master *master = platform_get_drvdata(pdev);
-+ struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
-+
-+ clk_enable(bs->clk);
-+ spi_master_resume(master);
-+
-+ return 0;
-+}
-+
-+static const struct dev_pm_ops bcm63xx_hsspi_pm_ops = {
-+ .suspend = bcm63xx_hsspi_suspend,
-+ .resume = bcm63xx_hsspi_resume,
-+};
-+
-+#define BCM63XX_HSSPI_PM_OPS (&bcm63xx_hsspi_pm_ops)
-+#else
-+#define BCM63XX_HSSPI_PM_OPS NULL
-+#endif
-+
-+
-+
-+static struct platform_driver bcm63xx_hsspi_driver = {
-+ .driver = {
-+ .name = "bcm63xx-hsspi",
-+ .owner = THIS_MODULE,
-+ .pm = BCM63XX_HSSPI_PM_OPS,
-+ },
-+ .probe = bcm63xx_hsspi_probe,
-+ .remove = __exit_p(bcm63xx_hsspi_remove),
-+};
-+
-+module_platform_driver(bcm63xx_hsspi_driver);
-+
-+MODULE_ALIAS("platform:bcm63xx_hsspi");
-+MODULE_DESCRIPTION("Broadcom BCM63xx HS SPI Controller driver");
-+MODULE_AUTHOR("Jonas Gorski <jonas.gorski@gmail.com>");
-+MODULE_LICENSE("GPL");
+++ /dev/null
-From d135d94b3d1fe599d13e7198d5f502912d694c13 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Sun, 3 Jul 2011 15:00:38 +0200
-Subject: [PATCH 29/60] MIPS: BCM63XX: Register SPI flash if present
-
-Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
----
- arch/mips/bcm63xx/dev-flash.c | 33 +++++++++++++++++++-
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 2 +
- 2 files changed, 33 insertions(+), 2 deletions(-)
-
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -16,9 +16,12 @@
- #include <linux/mtd/mtd.h>
- #include <linux/mtd/partitions.h>
- #include <linux/mtd/physmap.h>
-+#include <linux/spi/spi.h>
-+#include <linux/spi/flash.h>
-
- #include <bcm63xx_cpu.h>
- #include <bcm63xx_dev_flash.h>
-+#include <bcm63xx_dev_hsspi.h>
- #include <bcm63xx_regs.h>
- #include <bcm63xx_io.h>
-
-@@ -55,6 +58,21 @@ static struct platform_device mtd_dev =
- },
- };
-
-+static struct flash_platform_data bcm63xx_flash_data = {
-+ .part_probe_types = bcm63xx_part_types,
-+};
-+
-+static struct spi_board_info bcm63xx_spi_flash_info[] = {
-+ {
-+ .bus_num = 0,
-+ .chip_select = 0,
-+ .mode = 0,
-+ .max_speed_hz = 781000,
-+ .modalias = "m25p80",
-+ .platform_data = &bcm63xx_flash_data,
-+ },
-+};
-+
- static int __init bcm63xx_detect_flash_type(void)
- {
- u32 val;
-@@ -62,6 +80,11 @@ static int __init bcm63xx_detect_flash_t
- switch (bcm63xx_get_cpu_id()) {
- case BCM6328_CPU_ID:
- val = bcm_misc_readl(MISC_STRAPBUS_6328_REG);
-+ if (val & STRAPBUS_6328_HSSPI_CLK_FAST)
-+ bcm63xx_spi_flash_info[0].max_speed_hz = 33333334;
-+ else
-+ bcm63xx_spi_flash_info[0].max_speed_hz = 16666667;
-+
- if (val & STRAPBUS_6328_BOOT_SEL_SERIAL)
- return BCM63XX_FLASH_TYPE_SERIAL;
- else
-@@ -85,6 +108,9 @@ static int __init bcm63xx_detect_flash_t
- return BCM63XX_FLASH_TYPE_NAND;
- case BCM6368_CPU_ID:
- val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
-+ if (val & STRAPBUS_6368_SPI_CLK_FAST)
-+ bcm63xx_spi_flash_info[0].max_speed_hz = 20000000;
-+
- switch (val & STRAPBUS_6368_BOOT_SEL_MASK) {
- case STRAPBUS_6368_BOOT_SEL_NAND:
- return BCM63XX_FLASH_TYPE_NAND;
-@@ -116,8 +142,13 @@ int __init bcm63xx_flash_register(void)
-
- return platform_device_register(&mtd_dev);
- case BCM63XX_FLASH_TYPE_SERIAL:
-- pr_warn("unsupported serial flash detected\n");
-- return -ENODEV;
-+ if (BCMCPU_IS_6328() || BCMCPU_IS_6362()) {
-+ bcm63xx_spi_flash_info[0].bus_num = 1;
-+ bcm63xx_flash_data.max_transfer_len = HSSPI_BUFFER_LEN;
-+ }
-+
-+ return spi_register_board_info(bcm63xx_spi_flash_info,
-+ ARRAY_SIZE(bcm63xx_spi_flash_info));
- case BCM63XX_FLASH_TYPE_NAND:
- pr_warn("unsupported NAND flash detected\n");
- return -ENODEV;
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -629,6 +629,7 @@
- #define GPIO_STRAPBUS_REG 0x40
- #define STRAPBUS_6358_BOOT_SEL_PARALLEL (1 << 1)
- #define STRAPBUS_6358_BOOT_SEL_SERIAL (0 << 1)
-+#define STRAPBUS_6368_SPI_CLK_FAST (1 << 6)
- #define STRAPBUS_6368_BOOT_SEL_MASK 0x3
- #define STRAPBUS_6368_BOOT_SEL_NAND 0
- #define STRAPBUS_6368_BOOT_SEL_SERIAL 1
-@@ -1443,6 +1444,7 @@
- #define STRAPBUS_6362_BOOT_SEL_NAND (0 << 15)
-
- #define MISC_STRAPBUS_6328_REG 0x240
-+#define STRAPBUS_6328_HSSPI_CLK_FAST (1 << 4)
- #define STRAPBUS_6328_FCVO_SHIFT 7
- #define STRAPBUS_6328_FCVO_MASK (0x1f << STRAPBUS_6328_FCVO_SHIFT)
- #define STRAPBUS_6328_BOOT_SEL_SERIAL (1 << 28)
+++ /dev/null
-From 266c506f4b262bd6aba0776a03d82c98e65d9906 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Tue, 1 May 2012 17:32:36 +0200
-Subject: [PATCH 63/79] MTD: physmap: allow passing pp_data
-
----
- drivers/mtd/maps/physmap.c | 4 +++-
- include/linux/mtd/physmap.h | 1 +
- 2 files changed, 4 insertions(+), 1 deletion(-)
-
---- a/drivers/mtd/maps/physmap.c
-+++ b/drivers/mtd/maps/physmap.c
-@@ -100,6 +100,7 @@ static int physmap_flash_probe(struct pl
- {
- struct physmap_flash_data *physmap_data;
- struct physmap_flash_info *info;
-+ struct mtd_part_parser_data *pp_data;
- const char **probe_type;
- const char **part_types;
- int err = 0;
-@@ -191,8 +192,9 @@ static int physmap_flash_probe(struct pl
- spin_lock_init(&info->vpp_lock);
-
- part_types = physmap_data->part_probe_types ? : part_probe_types;
-+ pp_data = physmap_data->pp_data ? physmap_data->pp_data : NULL;
-
-- mtd_device_parse_register(info->cmtd, part_types, NULL,
-+ mtd_device_parse_register(info->cmtd, part_types, pp_data,
- physmap_data->parts, physmap_data->nr_parts);
- return 0;
-
---- a/include/linux/mtd/physmap.h
-+++ b/include/linux/mtd/physmap.h
-@@ -32,6 +32,7 @@ struct physmap_flash_data {
- char *probe_type;
- struct mtd_partition *parts;
- const char **part_probe_types;
-+ struct mtd_part_parser_data *pp_data;
- };
-
- #endif /* __LINUX_MTD_PHYSMAP__ */
+++ /dev/null
-From 8879e209111192c5e9752d7bd203cf7582693328 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Thu, 3 May 2012 14:40:03 +0200
-Subject: [PATCH 58/72] BCM63XX: allow providing fixup data in board data
-
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 9 ++++++++-
- arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 10 ++++++++++
- 2 files changed, 18 insertions(+), 1 deletion(-)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -33,6 +33,7 @@
- #include <bcm63xx_dev_usb_ohci.h>
- #include <bcm63xx_dev_usb_usbd.h>
- #include <board_bcm963xx.h>
-+#include <pci_ath9k_fixup.h>
-
- #include <uapi/linux/bcm963xx_tag.h>
-
-@@ -907,6 +908,7 @@ int __init board_register_devices(void)
- {
- int button_count = 0;
- int led_count = 0;
-+ int i;
-
- if (board.has_uart0)
- bcm63xx_uart_register(0);
-@@ -945,7 +947,8 @@ int __init board_register_devices(void)
- * do this after registering enet devices
- */
- #ifdef CONFIG_SSB_PCIHOST
-- if (!bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) {
-+ if (!board.has_caldata &&
-+ !bcm63xx_nvram_get_mac_address(bcm63xx_sprom.il0mac)) {
- memcpy(bcm63xx_sprom.et0mac, bcm63xx_sprom.il0mac, ETH_ALEN);
- memcpy(bcm63xx_sprom.et1mac, bcm63xx_sprom.il0mac, ETH_ALEN);
- if (ssb_arch_register_fallback_sprom(
-@@ -987,5 +990,9 @@ int __init board_register_devices(void)
- platform_device_register(&bcm63xx_gpio_keys_device);
- }
-
-+ /* register any fixups */
-+ for (i = 0; i < board.has_caldata; i++)
-+ pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset);
-+
- return 0;
- }
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -8,6 +8,7 @@
- #include <bcm63xx_dev_enet.h>
- #include <bcm63xx_dev_usb_usbd.h>
- #include <bcm63xx_dev_dsp.h>
-+#include <pci_ath9k_fixup.h>
-
- /*
- * flash mapping
-@@ -15,6 +16,11 @@
- #define BCM963XX_CFE_VERSION_OFFSET 0x570
- #define BCM963XX_NVRAM_OFFSET 0x580
-
-+struct ath9k_caldata {
-+ unsigned int slot;
-+ u32 caldata_offset;
-+};
-+
- /*
- * board definition
- */
-@@ -34,6 +40,10 @@ struct board_info {
- unsigned int has_dsp:1;
- unsigned int has_uart0:1;
- unsigned int has_uart1:1;
-+ unsigned int has_caldata:2;
-+
-+ /* wifi calibration data config */
-+ struct ath9k_caldata caldata[2];
-
- /* ethernet config */
- struct bcm63xx_enet_platform_data enet0;
+++ /dev/null
-From 7f17dfe9009beb07a3de0e380932a725293829df Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Tue, 1 May 2012 17:33:03 +0200
-Subject: [PATCH 64/79] MTD: m25p80: allow passing pp_data
-
----
- drivers/mtd/devices/m25p80.c | 3 +++
- include/linux/spi/flash.h | 2 ++
- 2 files changed, 5 insertions(+)
-
---- a/drivers/mtd/devices/m25p80.c
-+++ b/drivers/mtd/devices/m25p80.c
-@@ -878,6 +878,9 @@ static int m25p_probe(struct spi_device
- dev_warn(&spi->dev, "unrecognized id %s\n", data->type);
- }
-
-+ if (data && data->pp_data)
-+ memcpy(&ppdata, data->pp_data, sizeof(ppdata));
-+
- info = (void *)id->driver_data;
-
- if (info->jedec_id) {
---- a/include/linux/spi/flash.h
-+++ b/include/linux/spi/flash.h
-@@ -12,6 +12,7 @@ struct mtd_part_parser_data;
- * with chips that can't be queried for JEDEC or other IDs
- * @part_probe_types: optional list of MTD parser names to use for
- * partitioning
-+ * @pp_data: optional partition parser data.
- *
- * @max_transfer_len: option maximum read/write length limitation for
- * SPI controllers not able to transfer any length commands.
-@@ -30,6 +31,7 @@ struct flash_platform_data {
- char *type;
-
- const char **part_probe_types;
-+ struct mtd_part_parser_data *pp_data;
-
- unsigned int max_transfer_len;
- /* we'll likely add more ... use JEDEC IDs, etc */
+++ /dev/null
-From f888824d352df894ab721a5ca067b0313500efe7 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Thu, 3 May 2012 12:17:54 +0200
-Subject: [PATCH 38/59] MIPS: BCM63XX: store the flash type in global variable
-
----
- arch/mips/bcm63xx/dev-flash.c | 36 +++++++++++++------
- .../include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 2 +
- 2 files changed, 26 insertions(+), 12 deletions(-)
-
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -25,6 +25,8 @@
- #include <bcm63xx_regs.h>
- #include <bcm63xx_io.h>
-
-+int bcm63xx_attached_flash = -1;
-+
- static struct mtd_partition mtd_partitions[] = {
- {
- .name = "cfe",
-@@ -86,26 +88,30 @@ static int __init bcm63xx_detect_flash_t
- bcm63xx_spi_flash_info[0].max_speed_hz = 16666667;
-
- if (val & STRAPBUS_6328_BOOT_SEL_SERIAL)
-- return BCM63XX_FLASH_TYPE_SERIAL;
-+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL;
- else
-- return BCM63XX_FLASH_TYPE_NAND;
-+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND;
-+ break;
- case BCM6338_CPU_ID:
- case BCM6345_CPU_ID:
- case BCM6348_CPU_ID:
- /* no way to auto detect so assume parallel */
-- return BCM63XX_FLASH_TYPE_PARALLEL;
-+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL;
-+ break;
- case BCM6358_CPU_ID:
- val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
- if (val & STRAPBUS_6358_BOOT_SEL_PARALLEL)
-- return BCM63XX_FLASH_TYPE_PARALLEL;
-+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL;
- else
-- return BCM63XX_FLASH_TYPE_SERIAL;
-+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL;
-+ break;
- case BCM6362_CPU_ID:
- val = bcm_misc_readl(MISC_STRAPBUS_6362_REG);
- if (val & STRAPBUS_6362_BOOT_SEL_SERIAL)
-- return BCM63XX_FLASH_TYPE_SERIAL;
-+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL;
- else
-- return BCM63XX_FLASH_TYPE_NAND;
-+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND;
-+ break;
- case BCM6368_CPU_ID:
- val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
- if (val & STRAPBUS_6368_SPI_CLK_FAST)
-@@ -113,25 +119,32 @@ static int __init bcm63xx_detect_flash_t
-
- switch (val & STRAPBUS_6368_BOOT_SEL_MASK) {
- case STRAPBUS_6368_BOOT_SEL_NAND:
-- return BCM63XX_FLASH_TYPE_NAND;
-+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_NAND;
-+ break;
- case STRAPBUS_6368_BOOT_SEL_SERIAL:
-- return BCM63XX_FLASH_TYPE_SERIAL;
-+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_SERIAL;
-+ break;
- case STRAPBUS_6368_BOOT_SEL_PARALLEL:
-- return BCM63XX_FLASH_TYPE_PARALLEL;
-+ bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL;
-+ break;
-+ default:
-+ return -EINVAL;
- }
- default:
- return -EINVAL;
- }
-+
-+ return 0;
- }
-
- int __init bcm63xx_flash_register(void)
- {
-- int flash_type;
- u32 val;
-
-- flash_type = bcm63xx_detect_flash_type();
-
-- switch (flash_type) {
-+ bcm63xx_detect_flash_type();
-+
-+ switch (bcm63xx_attached_flash) {
- case BCM63XX_FLASH_TYPE_PARALLEL:
- /* read base address of boot chip select (0) */
- val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-@@ -154,7 +167,7 @@ int __init bcm63xx_flash_register(void)
- return -ENODEV;
- default:
- pr_err("flash detection failed for BCM%x: %d\n",
-- bcm63xx_get_cpu_id(), flash_type);
-+ bcm63xx_get_cpu_id(), bcm63xx_attached_flash);
- return -ENODEV;
- }
- }
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
-@@ -7,6 +7,8 @@ enum {
- BCM63XX_FLASH_TYPE_NAND,
- };
-
-+extern int bcm63xx_attached_flash;
-+
- int __init bcm63xx_flash_register(void);
-
- #endif /* __BCM63XX_FLASH_H */
+++ /dev/null
-From bbebbf735a02b6d044ed928978ab4bd5f1833364 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Thu, 3 May 2012 14:36:11 +0200
-Subject: [PATCH 61/72] BCM63XX: add a fixup for ath9k devices
-
----
- arch/mips/bcm63xx/Makefile | 3 +-
- arch/mips/bcm63xx/pci-ath9k-fixup.c | 190 ++++++++++++++++++++
- .../include/asm/mach-bcm63xx/pci_ath9k_fixup.h | 7 +
- 3 files changed, 199 insertions(+), 1 deletion(-)
- create mode 100644 arch/mips/bcm63xx/pci-ath9k-fixup.c
- create mode 100644 arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
-
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -2,7 +2,7 @@ obj-y += clk.o cpu.o cs.o gpio.o irq.o
- setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
- dev-hsspi.o dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o \
- dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \
-- usb-common.o
-+ pci-ath9k-fixup.o usb-common.o
- obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
-
- obj-y += boards/
---- /dev/null
-+++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c
-@@ -0,0 +1,190 @@
-+/*
-+ * Broadcom BCM63XX Ath9k EEPROM fixup helper.
-+ *
-+ * Copytight (C) 2012 Jonas Gorski <jonas.gorski@gmail.com>
-+ *
-+ * Based on
-+ *
-+ * Atheros AP94 reference board PCI initialization
-+ *
-+ * Copyright (C) 2009-2010 Gabor Juhos <juhosg@openwrt.org>
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License version 2 as published
-+ * by the Free Software Foundation.
-+ */
-+
-+#include <linux/pci.h>
-+#include <linux/delay.h>
-+#include <linux/ath9k_platform.h>
-+
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_io.h>
-+#include <bcm63xx_nvram.h>
-+#include <bcm63xx_dev_pci.h>
-+#include <bcm63xx_dev_flash.h>
-+#include <bcm63xx_dev_hsspi.h>
-+#include <pci_ath9k_fixup.h>
-+
-+struct ath9k_fixup {
-+ unsigned slot;
-+ u8 mac[ETH_ALEN];
-+ struct ath9k_platform_data pdata;
-+};
-+
-+static int ath9k_num_fixups;
-+static struct ath9k_fixup ath9k_fixups[2] = {
-+ {
-+ .slot = 255,
-+ .pdata = {
-+ .led_pin = -1,
-+ },
-+ },
-+ {
-+ .slot = 255,
-+ .pdata = {
-+ .led_pin = -1,
-+ },
-+ },
-+};
-+
-+static u16 *bcm63xx_read_eeprom(u16 *eeprom, u32 offset)
-+{
-+ u32 addr;
-+
-+ if (BCMCPU_IS_6328()) {
-+ addr = 0x18000000;
-+ } else {
-+ addr = bcm_mpi_readl(MPI_CSBASE_REG(0));
-+ addr &= MPI_CSBASE_BASE_MASK;
-+ }
-+
-+ switch (bcm63xx_attached_flash) {
-+ case BCM63XX_FLASH_TYPE_PARALLEL:
-+ memcpy(eeprom, (void *)KSEG1ADDR(addr + offset), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16));
-+ return eeprom;
-+ case BCM63XX_FLASH_TYPE_SERIAL:
-+ /* the first megabyte is memory mapped */
-+ if (offset < 0x100000) {
-+ memcpy(eeprom, (void *)KSEG1ADDR(addr + offset), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16));
-+ return eeprom;
-+ }
-+
-+ if (BCMCPU_IS_6328()) {
-+ /* we can change the memory mapped megabyte */
-+ bcm_hsspi_writel(offset & 0xf00000, 0x18);
-+ memcpy(eeprom, (void *)KSEG1ADDR(addr + (offset & 0xfffff)), ATH9K_PLAT_EEP_MAX_WORDS * sizeof(u16));
-+ bcm_hsspi_writel(0, 0x18);
-+ return eeprom;
-+ }
-+ /* can't do anything here without talking to the SPI controller. */
-+ case BCM63XX_FLASH_TYPE_NAND:
-+ default:
-+ return NULL;
-+ }
-+}
-+
-+static void ath9k_pci_fixup(struct pci_dev *dev)
-+{
-+ void __iomem *mem;
-+ struct ath9k_platform_data *pdata = NULL;
-+ u16 *cal_data = NULL;
-+ u16 cmd;
-+ u32 bar0;
-+ u32 val;
-+ unsigned i;
-+
-+ for (i = 0; i < ath9k_num_fixups; i++) {
-+ if (ath9k_fixups[i].slot != PCI_SLOT(dev->devfn))
-+ continue;
-+
-+ cal_data = ath9k_fixups[i].pdata.eeprom_data;
-+ pdata = &ath9k_fixups[i].pdata;
-+ break;
-+ }
-+
-+ if (cal_data == NULL)
-+ return;
-+
-+ if (*cal_data != 0xa55a) {
-+ pr_err("pci %s: invalid calibration data\n", pci_name(dev));
-+ return;
-+ }
-+
-+ pr_info("pci %s: fixup device configuration\n", pci_name(dev));
-+
-+ switch (bcm63xx_get_cpu_id()) {
-+ case BCM6328_CPU_ID:
-+ val = BCM_PCIE_MEM_BASE_PA;
-+ break;
-+ case BCM6348_CPU_ID:
-+ case BCM6358_CPU_ID:
-+ case BCM6368_CPU_ID:
-+ val = BCM_PCI_MEM_BASE_PA;
-+ break;
-+ default:
-+ BUG();
-+ }
-+
-+ mem = ioremap(val, 0x10000);
-+ if (!mem) {
-+ pr_err("pci %s: ioremap error\n", pci_name(dev));
-+ return;
-+ }
-+
-+ pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &bar0);
-+ pci_read_config_dword(dev, PCI_BASE_ADDRESS_0, &bar0);
-+ pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, val);
-+
-+ pci_read_config_word(dev, PCI_COMMAND, &cmd);
-+ cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
-+ pci_write_config_word(dev, PCI_COMMAND, cmd);
-+
-+ /* set offset to first reg address */
-+ cal_data += 3;
-+ while(*cal_data != 0xffff) {
-+ u32 reg;
-+ reg = *cal_data++;
-+ val = *cal_data++;
-+ val |= (*cal_data++) << 16;
-+
-+ writel(val, mem + reg);
-+ udelay(100);
-+ }
-+
-+ pci_read_config_dword(dev, PCI_VENDOR_ID, &val);
-+ dev->vendor = val & 0xffff;
-+ dev->device = (val >> 16) & 0xffff;
-+
-+ pci_read_config_dword(dev, PCI_CLASS_REVISION, &val);
-+ dev->revision = val & 0xff;
-+ dev->class = val >> 8; /* upper 3 bytes */
-+
-+ pci_read_config_word(dev, PCI_COMMAND, &cmd);
-+ cmd &= ~(PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
-+ pci_write_config_word(dev, PCI_COMMAND, cmd);
-+
-+ pci_write_config_dword(dev, PCI_BASE_ADDRESS_0, bar0);
-+
-+ iounmap(mem);
-+
-+ dev->dev.platform_data = pdata;
-+}
-+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup);
-+
-+void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset)
-+{
-+ if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups))
-+ return;
-+
-+ ath9k_fixups[ath9k_num_fixups].slot = slot;
-+
-+ if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset))
-+ return;
-+
-+ if (bcm63xx_nvram_get_mac_address(ath9k_fixups[ath9k_num_fixups].mac))
-+ return;
-+
-+ ath9k_fixups[ath9k_num_fixups].pdata.macaddr = ath9k_fixups[ath9k_num_fixups].mac;
-+ ath9k_num_fixups++;
-+}
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
-@@ -0,0 +1,7 @@
-+#ifndef _PCI_ATH9K_FIXUP
-+#define _PCI_ATH9K_FIXUP
-+
-+
-+void pci_enable_ath9k_fixup(unsigned slot, u32 offset) __init;
-+
-+#endif /* _PCI_ATH9K_FIXUP */
+++ /dev/null
-Allow bcm63xxpart to receive a caldata offset if calibration data is
-contained in flash.
----
- drivers/mtd/bcm63xxpart.c | 51 ++++++++++++++++++++++++++++++++++++---
- include/linux/mtd/partitions.h | 2 +
- 2 files changed, 49 insertions(+), 4 deletions(-)
-
---- a/drivers/mtd/bcm63xxpart.c
-+++ b/drivers/mtd/bcm63xxpart.c
-@@ -53,10 +53,12 @@ static int bcm63xx_parse_cfe_partitions(
- struct mtd_partition *parts;
- int ret;
- size_t retlen;
-- unsigned int rootfsaddr, kerneladdr, spareaddr;
-+ unsigned int rootfsaddr, kerneladdr, spareaddr, nvramaddr;
- unsigned int rootfslen, kernellen, sparelen, totallen;
- unsigned int cfelen, nvramlen;
- unsigned int cfe_erasesize;
-+ unsigned int caldatalen1 = 0, caldataaddr1 = 0;
-+ unsigned int caldatalen2 = 0, caldataaddr2 = 0;
- int i;
- u32 computed_crc;
- bool rootfs_first = false;
-@@ -70,6 +72,24 @@ static int bcm63xx_parse_cfe_partitions(
- cfelen = cfe_erasesize;
- nvramlen = bcm63xx_nvram_get_psi_size();
- nvramlen = roundup(nvramlen, cfe_erasesize);
-+ nvramaddr = master->size - nvramlen;
-+
-+ if (data) {
-+ if (data->caldata[0]) {
-+ caldatalen1 = cfe_erasesize;
-+ caldataaddr1 = rounddown(data->caldata[0],
-+ cfe_erasesize);
-+ }
-+ if (data->caldata[1]) {
-+ caldatalen2 = cfe_erasesize;
-+ caldataaddr2 = rounddown(data->caldata[1],
-+ cfe_erasesize);
-+ }
-+ if (caldataaddr1 == caldataaddr2) {
-+ caldataaddr2 = 0;
-+ caldatalen2 = 0;
-+ }
-+ }
-
- /* Allocate memory for buffer */
- buf = vmalloc(sizeof(struct bcm_tag));
-@@ -121,7 +141,7 @@ static int bcm63xx_parse_cfe_partitions(
- rootfsaddr = 0;
- spareaddr = cfelen;
- }
-- sparelen = master->size - spareaddr - nvramlen;
-+ sparelen = min_not_zero(nvramaddr, caldataaddr1) - spareaddr;
-
- /* Determine number of partitions */
- if (rootfslen > 0)
-@@ -130,6 +150,12 @@ static int bcm63xx_parse_cfe_partitions(
- if (kernellen > 0)
- nrparts++;
-
-+ if (caldatalen1 > 0)
-+ nrparts++;
-+
-+ if (caldatalen2 > 0)
-+ nrparts++;
-+
- /* Ask kernel for more memory */
- parts = kzalloc(sizeof(*parts) * nrparts + 10 * nrparts, GFP_KERNEL);
- if (!parts) {
-@@ -167,15 +193,32 @@ static int bcm63xx_parse_cfe_partitions(
- curpart++;
- }
-
-+ if (caldatalen1 > 0) {
-+ if (caldatalen2 > 0)
-+ parts[curpart].name = "cal_data1";
-+ else
-+ parts[curpart].name = "cal_data";
-+ parts[curpart].offset = caldataaddr1;
-+ parts[curpart].size = caldatalen1;
-+ curpart++;
-+ }
-+
-+ if (caldatalen2 > 0) {
-+ parts[curpart].name = "cal_data2";
-+ parts[curpart].offset = caldataaddr2;
-+ parts[curpart].size = caldatalen2;
-+ curpart++;
-+ }
-+
- parts[curpart].name = "nvram";
-- parts[curpart].offset = master->size - nvramlen;
-+ parts[curpart].offset = nvramaddr;
- parts[curpart].size = nvramlen;
- curpart++;
-
- /* Global partition "linux" to make easy firmware upgrade */
- parts[curpart].name = "linux";
- parts[curpart].offset = cfelen;
-- parts[curpart].size = master->size - cfelen - nvramlen;
-+ parts[curpart].size = min_not_zero(nvramaddr, caldataaddr1) - cfelen;
-
- for (i = 0; i < nrparts; i++)
- pr_info("Partition %d is %s offset %llx and length %llx\n", i,
---- a/include/linux/mtd/partitions.h
-+++ b/include/linux/mtd/partitions.h
-@@ -58,10 +58,12 @@ struct device_node;
- /**
- * struct mtd_part_parser_data - used to pass data to MTD partition parsers.
- * @origin: for RedBoot, start address of MTD device
-+ * @caldata: for CFE, start address of wifi calibration data
- * @of_node: for OF parsers, device node containing partitioning information
- */
- struct mtd_part_parser_data {
- unsigned long origin;
-+ unsigned long caldata[2];
- struct device_node *of_node;
- };
-
+++ /dev/null
-From 977f8a30103b9c4992cab8f49357fe0d4274004f Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Thu, 3 May 2012 14:55:26 +0200
-Subject: [PATCH 69/80] MIPS: BCM63XX: pass caldata info to flash
-
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 2 +-
- arch/mips/bcm63xx/dev-flash.c | 9 ++++++++-
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 4 +++-
- 3 files changed, 12 insertions(+), 3 deletions(-)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -966,7 +966,7 @@ int __init board_register_devices(void)
- if (board.num_spis)
- spi_register_board_info(board.spis, board.num_spis);
-
-- bcm63xx_flash_register();
-+ bcm63xx_flash_register(board.has_caldata, board.caldata);
-
- /* count number of LEDs defined by this device */
- while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name)
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -35,12 +35,15 @@ static struct mtd_partition mtd_partitio
- }
- };
-
-+static struct mtd_part_parser_data bcm63xx_parser_data;
-+
- static const char *bcm63xx_part_types[] = { "bcm63xxpart", "RedBoot", NULL };
-
- static struct physmap_flash_data flash_data = {
- .width = 2,
- .parts = mtd_partitions,
- .part_probe_types = bcm63xx_part_types,
-+ .pp_data = &bcm63xx_parser_data,
- };
-
- static struct resource mtd_resources[] = {
-@@ -62,6 +65,7 @@ static struct platform_device mtd_dev =
-
- static struct flash_platform_data bcm63xx_flash_data = {
- .part_probe_types = bcm63xx_part_types,
-+ .pp_data = &bcm63xx_parser_data,
- };
-
- static struct spi_board_info bcm63xx_spi_flash_info[] = {
-@@ -137,10 +141,13 @@ static int __init bcm63xx_detect_flash_t
- return 0;
- }
-
--int __init bcm63xx_flash_register(void)
-+int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata)
- {
- u32 val;
-+ unsigned int i;
-
-+ for (i = 0; i < num_caldata; i++)
-+ bcm63xx_parser_data.caldata[i] = caldata[i].caldata_offset;
-
- bcm63xx_detect_flash_type();
-
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
-@@ -1,6 +1,8 @@
- #ifndef __BCM63XX_FLASH_H
- #define __BCM63XX_FLASH_H
-
-+#include <board_bcm963xx.h>
-+
- enum {
- BCM63XX_FLASH_TYPE_PARALLEL,
- BCM63XX_FLASH_TYPE_SERIAL,
-@@ -9,6 +11,6 @@ enum {
-
- extern int bcm63xx_attached_flash;
-
--int __init bcm63xx_flash_register(void);
-+int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata);
-
- #endif /* __BCM63XX_FLASH_H */
+++ /dev/null
-From 1b0b5d325d0cc50cade62afd6a9416fb3cd1e658 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 7 Jan 2013 17:42:45 +0100
-Subject: [PATCH 69/72] 443-MIPS-BCM63XX-enable-enet-for-BCM6345.patch
-
----
- arch/mips/bcm63xx/dev-enet.c | 63 ++++++-
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h | 3 +-
- .../include/asm/mach-bcm63xx/bcm63xx_dev_enet.h | 88 +++++++++
- arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h | 43 ++++-
- drivers/net/ethernet/broadcom/bcm63xx_enet.c | 199 ++++++++++++--------
- drivers/net/ethernet/broadcom/bcm63xx_enet.h | 15 ++
- 6 files changed, 320 insertions(+), 91 deletions(-)
-
---- a/arch/mips/bcm63xx/dev-enet.c
-+++ b/arch/mips/bcm63xx/dev-enet.c
-@@ -9,10 +9,44 @@
- #include <linux/init.h>
- #include <linux/kernel.h>
- #include <linux/platform_device.h>
-+#include <linux/export.h>
- #include <bcm63xx_dev_enet.h>
- #include <bcm63xx_io.h>
- #include <bcm63xx_regs.h>
-
-+#ifdef BCMCPU_RUNTIME_DETECT
-+static const unsigned long bcm6xxx_regs_enetdmac[] = {
-+ [ENETDMAC_CHANCFG] = ENETDMAC_CHANCFG_REG,
-+ [ENETDMAC_IR] = ENETDMAC_IR_REG,
-+ [ENETDMAC_IRMASK] = ENETDMAC_IRMASK_REG,
-+ [ENETDMAC_MAXBURST] = ENETDMAC_MAXBURST_REG,
-+};
-+
-+static const unsigned long bcm6345_regs_enetdmac[] = {
-+ [ENETDMAC_CHANCFG] = ENETDMA_6345_CHANCFG_REG,
-+ [ENETDMAC_IR] = ENETDMA_6345_IR_REG,
-+ [ENETDMAC_IRMASK] = ENETDMA_6345_IRMASK_REG,
-+ [ENETDMAC_MAXBURST] = ENETDMA_6345_MAXBURST_REG,
-+ [ENETDMAC_BUFALLOC] = ENETDMA_6345_BUFALLOC_REG,
-+ [ENETDMAC_RSTART] = ENETDMA_6345_RSTART_REG,
-+ [ENETDMAC_FC] = ENETDMA_6345_FC_REG,
-+ [ENETDMAC_LEN] = ENETDMA_6345_LEN_REG,
-+};
-+
-+const unsigned long *bcm63xx_regs_enetdmac;
-+EXPORT_SYMBOL(bcm63xx_regs_enetdmac);
-+
-+static __init void bcm63xx_enetdmac_regs_init(void)
-+{
-+ if (BCMCPU_IS_6345())
-+ bcm63xx_regs_enetdmac = bcm6345_regs_enetdmac;
-+ else
-+ bcm63xx_regs_enetdmac = bcm6xxx_regs_enetdmac;
-+}
-+#else
-+static __init void bcm63xx_enetdmac_regs_init(void) { }
-+#endif
-+
- static struct resource shared_res[] = {
- {
- .start = -1, /* filled at runtime */
-@@ -137,12 +171,19 @@ static int __init register_shared(void)
- if (shared_device_registered)
- return 0;
-
-+ bcm63xx_enetdmac_regs_init();
-+
- shared_res[0].start = bcm63xx_regset_address(RSET_ENETDMA);
- shared_res[0].end = shared_res[0].start;
-- shared_res[0].end += (RSET_ENETDMA_SIZE) - 1;
-+ if (BCMCPU_IS_6345())
-+ shared_res[0].end += (RSET_6345_ENETDMA_SIZE) - 1;
-+ else
-+ shared_res[0].end += (RSET_ENETDMA_SIZE) - 1;
-
- if (BCMCPU_IS_6328() || BCMCPU_IS_6362() || BCMCPU_IS_6368())
- chan_count = 32;
-+ else if (BCMCPU_IS_6345())
-+ chan_count = 8;
- else
- chan_count = 16;
-
-@@ -172,7 +213,7 @@ int __init bcm63xx_enet_register(int uni
- if (unit > 1)
- return -ENODEV;
-
-- if (unit == 1 && BCMCPU_IS_6338())
-+ if (unit == 1 && (BCMCPU_IS_6338() || BCMCPU_IS_6345()))
- return -ENODEV;
-
- ret = register_shared();
-@@ -213,6 +254,20 @@ int __init bcm63xx_enet_register(int uni
- dpd->phy_interrupt = bcm63xx_get_irq_number(IRQ_ENET_PHY);
- }
-
-+ dpd->dma_chan_en_mask = ENETDMAC_CHANCFG_EN_MASK;
-+ dpd->dma_chan_int_mask = ENETDMAC_IR_PKTDONE_MASK;
-+ if (BCMCPU_IS_6345()) {
-+ dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_CHAINING_MASK;
-+ dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_WRAP_EN_MASK;
-+ dpd->dma_chan_en_mask |= ENETDMAC_CHANCFG_FLOWC_EN_MASK;
-+ dpd->dma_chan_int_mask |= ENETDMA_IR_BUFDONE_MASK;
-+ dpd->dma_chan_int_mask |= ENETDMA_IR_NOTOWNER_MASK;
-+ dpd->dma_chan_width = ENETDMA_6345_CHAN_WIDTH;
-+ dpd->dma_no_sram = 1;
-+ dpd->dma_desc_shift = ENETDMA_6345_DESC_SHIFT;
-+ } else
-+ dpd->dma_chan_width = ENETDMA_CHAN_WIDTH;
-+
- ret = platform_device_register(pdev);
- if (ret)
- return ret;
-@@ -246,6 +301,10 @@ bcm63xx_enetsw_register(const struct bcm
- else if (BCMCPU_IS_6362() || BCMCPU_IS_6368())
- enetsw_pd.num_ports = ENETSW_PORTS_6368;
-
-+ enetsw_pd.dma_chan_width = ENETDMA_CHAN_WIDTH;
-+ enetsw_pd.dma_chan_en_mask = ENETDMAC_CHANCFG_EN_MASK;
-+ enetsw_pd.dma_chan_int_mask = ENETDMAC_IR_PKTDONE_MASK;
-+
- ret = platform_device_register(&bcm63xx_enetsw_device);
- if (ret)
- return ret;
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-@@ -175,6 +175,7 @@ enum bcm63xx_regs_set {
- #define BCM_6368_RSET_SPI_SIZE 1804
- #define RSET_ENET_SIZE 2048
- #define RSET_ENETDMA_SIZE 256
-+#define RSET_6345_ENETDMA_SIZE 64
- #define RSET_ENETDMAC_SIZE(chans) (16 * (chans))
- #define RSET_ENETDMAS_SIZE(chans) (16 * (chans))
- #define RSET_ENETSW_SIZE 65536
-@@ -305,7 +306,7 @@ enum bcm63xx_regs_set {
- #define BCM_6345_USBDMA_BASE (0xfffe2800)
- #define BCM_6345_ENET0_BASE (0xfffe1800)
- #define BCM_6345_ENETDMA_BASE (0xfffe2800)
--#define BCM_6345_ENETDMAC_BASE (0xfffe2900)
-+#define BCM_6345_ENETDMAC_BASE (0xfffe2840)
- #define BCM_6345_ENETDMAS_BASE (0xfffe2a00)
- #define BCM_6345_ENETSW_BASE (0xdeadbeef)
- #define BCM_6345_PCMCIA_BASE (0xfffe2028)
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_enet.h
-@@ -4,6 +4,8 @@
- #include <linux/if_ether.h>
- #include <linux/init.h>
-
-+#include <bcm63xx_regs.h>
-+
- /*
- * on board ethernet platform data
- */
-@@ -37,6 +39,21 @@ struct bcm63xx_enet_platform_data {
- int phy_id, int reg),
- void (*mii_write)(struct net_device *dev,
- int phy_id, int reg, int val));
-+
-+ /* DMA channel enable mask */
-+ u32 dma_chan_en_mask;
-+
-+ /* DMA channel interrupt mask */
-+ u32 dma_chan_int_mask;
-+
-+ /* Set to one if DMA engine has *no* SRAM */
-+ unsigned int dma_no_sram;
-+
-+ /* DMA channel register width */
-+ unsigned int dma_chan_width;
-+
-+ /* DMA descriptor shift */
-+ unsigned int dma_desc_shift;
- };
-
- /*
-@@ -63,6 +80,15 @@ struct bcm63xx_enetsw_platform_data {
- char mac_addr[ETH_ALEN];
- int num_ports;
- struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT];
-+
-+ /* DMA channel enable mask */
-+ u32 dma_chan_en_mask;
-+
-+ /* DMA channel interrupt mask */
-+ u32 dma_chan_int_mask;
-+
-+ /* DMA channel register width */
-+ unsigned int dma_chan_width;
- };
-
- int __init bcm63xx_enet_register(int unit,
-@@ -70,4 +96,69 @@ int __init bcm63xx_enet_register(int uni
-
- int bcm63xx_enetsw_register(const struct bcm63xx_enetsw_platform_data *pd);
-
-+enum bcm63xx_regs_enetdmac {
-+ ENETDMAC_CHANCFG,
-+ ENETDMAC_IR,
-+ ENETDMAC_IRMASK,
-+ ENETDMAC_MAXBURST,
-+ ENETDMAC_BUFALLOC,
-+ ENETDMAC_RSTART,
-+ ENETDMAC_FC,
-+ ENETDMAC_LEN,
-+};
-+
-+static inline unsigned long bcm63xx_enetdmacreg(enum bcm63xx_regs_enetdmac reg)
-+{
-+#ifdef BCMCPU_RUNTIME_DETECT
-+ extern const unsigned long *bcm63xx_regs_enetdmac;
-+
-+ return bcm63xx_regs_enetdmac[reg];
-+#else
-+#ifdef CONFIG_BCM63XX_CPU_6345
-+ switch (reg) {
-+ case ENETDMAC_CHANCFG:
-+ return ENETDMA_6345_CHANCFG_REG;
-+ case ENETDMAC_IR:
-+ return ENETDMA_6345_IR_REG;
-+ case ENETDMAC_IRMASK:
-+ return ENETDMA_6345_IRMASK_REG;
-+ case ENETDMAC_MAXBURST:
-+ return ENETDMA_6345_MAXBURST_REG;
-+ case ENETDMAC_BUFALLOC:
-+ return ENETDMA_6345_BUFALLOC_REG;
-+ case ENETDMAC_RSTART:
-+ return ENETDMA_6345_RSTART_REG;
-+ case ENETDMAC_FC:
-+ return ENETDMA_6345_FC_REG;
-+ case ENETDMAC_LEN:
-+ return ENETDMA_6345_LEN_REG;
-+ }
-+#endif
-+#if defined(CONFIG_BCM63XX_CPU_6328) || \
-+ defined(CONFIG_BCM63XX_CPU_6338) || \
-+ defined(CONFIG_BCM63XX_CPU_6348) || \
-+ defined(CONFIG_BCM63XX_CPU_6358) || \
-+ defined(CONFIG_BCM63XX_CPU_6362) || \
-+ defined(CONFIG_BCM63XX_CPU_6368)
-+ switch (reg) {
-+ case ENETDMAC_CHANCFG:
-+ return ENETDMAC_CHANCFG_REG;
-+ case ENETDMAC_IR:
-+ return ENETDMAC_IR_REG;
-+ case ENETDMAC_IRMASK:
-+ return ENETDMAC_IRMASK_REG;
-+ case ENETDMAC_MAXBURST:
-+ return ENETDMAC_MAXBURST_REG;
-+ case ENETDMAC_BUFALLOC:
-+ case ENETDMAC_RSTART:
-+ case ENETDMAC_FC:
-+ case ENETDMAC_LEN:
-+ return 0;
-+ }
-+#endif
-+#endif
-+ return 0;
-+}
-+
-+
- #endif /* ! BCM63XX_DEV_ENET_H_ */
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -730,6 +730,8 @@
- /*************************************************************************
- * _REG relative to RSET_ENETDMA
- *************************************************************************/
-+#define ENETDMA_CHAN_WIDTH 0x10
-+#define ENETDMA_6345_CHAN_WIDTH 0x40
-
- /* Controller Configuration Register */
- #define ENETDMA_CFG_REG (0x0)
-@@ -785,31 +787,56 @@
- /* State Ram Word 4 */
- #define ENETDMA_SRAM4_REG(x) (0x20c + (x) * 0x10)
-
-+/* Broadcom 6345 ENET DMA definitions */
-+#define ENETDMA_6345_CHANCFG_REG (0x00)
-+
-+#define ENETDMA_6345_MAXBURST_REG (0x40)
-+
-+#define ENETDMA_6345_RSTART_REG (0x08)
-+
-+#define ENETDMA_6345_LEN_REG (0x0C)
-+
-+#define ENETDMA_6345_IR_REG (0x14)
-+
-+#define ENETDMA_6345_IRMASK_REG (0x18)
-+
-+#define ENETDMA_6345_FC_REG (0x1C)
-+
-+#define ENETDMA_6345_BUFALLOC_REG (0x20)
-+
-+/* Shift down for EOP, SOP and WRAP bits */
-+#define ENETDMA_6345_DESC_SHIFT (3)
-
- /*************************************************************************
- * _REG relative to RSET_ENETDMAC
- *************************************************************************/
-
- /* Channel Configuration register */
--#define ENETDMAC_CHANCFG_REG(x) ((x) * 0x10)
-+#define ENETDMAC_CHANCFG_REG (0x0)
- #define ENETDMAC_CHANCFG_EN_SHIFT 0
- #define ENETDMAC_CHANCFG_EN_MASK (1 << ENETDMAC_CHANCFG_EN_SHIFT)
- #define ENETDMAC_CHANCFG_PKTHALT_SHIFT 1
- #define ENETDMAC_CHANCFG_PKTHALT_MASK (1 << ENETDMAC_CHANCFG_PKTHALT_SHIFT)
- #define ENETDMAC_CHANCFG_BUFHALT_SHIFT 2
- #define ENETDMAC_CHANCFG_BUFHALT_MASK (1 << ENETDMAC_CHANCFG_BUFHALT_SHIFT)
-+#define ENETDMAC_CHANCFG_CHAINING_SHIFT 2
-+#define ENETDMAC_CHANCFG_CHAINING_MASK (1 << ENETDMAC_CHANCFG_CHAINING_SHIFT)
-+#define ENETDMAC_CHANCFG_WRAP_EN_SHIFT 3
-+#define ENETDMAC_CHANCFG_WRAP_EN_MASK (1 << ENETDMAC_CHANCFG_WRAP_EN_SHIFT)
-+#define ENETDMAC_CHANCFG_FLOWC_EN_SHIFT 4
-+#define ENETDMAC_CHANCFG_FLOWC_EN_MASK (1 << ENETDMAC_CHANCFG_FLOWC_EN_SHIFT)
-
- /* Interrupt Control/Status register */
--#define ENETDMAC_IR_REG(x) (0x4 + (x) * 0x10)
-+#define ENETDMAC_IR_REG (0x4)
- #define ENETDMAC_IR_BUFDONE_MASK (1 << 0)
- #define ENETDMAC_IR_PKTDONE_MASK (1 << 1)
- #define ENETDMAC_IR_NOTOWNER_MASK (1 << 2)
-
- /* Interrupt Mask register */
--#define ENETDMAC_IRMASK_REG(x) (0x8 + (x) * 0x10)
-+#define ENETDMAC_IRMASK_REG (0x8)
-
- /* Maximum Burst Length */
--#define ENETDMAC_MAXBURST_REG(x) (0xc + (x) * 0x10)
-+#define ENETDMAC_MAXBURST_REG (0xc)
-
-
- /*************************************************************************
-@@ -817,16 +844,16 @@
- *************************************************************************/
-
- /* Ring Start Address register */
--#define ENETDMAS_RSTART_REG(x) ((x) * 0x10)
-+#define ENETDMAS_RSTART_REG (0x0)
-
- /* State Ram Word 2 */
--#define ENETDMAS_SRAM2_REG(x) (0x4 + (x) * 0x10)
-+#define ENETDMAS_SRAM2_REG (0x4)
-
- /* State Ram Word 3 */
--#define ENETDMAS_SRAM3_REG(x) (0x8 + (x) * 0x10)
-+#define ENETDMAS_SRAM3_REG (0x8)
-
- /* State Ram Word 4 */
--#define ENETDMAS_SRAM4_REG(x) (0xc + (x) * 0x10)
-+#define ENETDMAS_SRAM4_REG (0xc)
-
-
- /*************************************************************************
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-@@ -115,26 +115,28 @@ static inline void enet_dma_writel(struc
- bcm_writel(val, bcm_enet_shared_base[0] + off);
- }
-
--static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off)
-+static inline u32 enet_dmac_readl(struct bcm_enet_priv *priv, u32 off, int chan)
- {
-- return bcm_readl(bcm_enet_shared_base[1] + off);
-+ return bcm_readl(bcm_enet_shared_base[1] +
-+ (bcm63xx_enetdmacreg(off) + (chan * priv->dma_chan_width)));
- }
-
- static inline void enet_dmac_writel(struct bcm_enet_priv *priv,
-- u32 val, u32 off)
-+ u32 val, u32 off, int chan)
- {
-- bcm_writel(val, bcm_enet_shared_base[1] + off);
-+ bcm_writel(val, bcm_enet_shared_base[1] +
-+ (bcm63xx_enetdmacreg(off) + (chan * priv->dma_chan_width)));
- }
-
--static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off)
-+static inline u32 enet_dmas_readl(struct bcm_enet_priv *priv, u32 off, int chan)
- {
-- return bcm_readl(bcm_enet_shared_base[2] + off);
-+ return bcm_readl(bcm_enet_shared_base[2] + (off + (chan * priv->dma_chan_width)));
- }
-
- static inline void enet_dmas_writel(struct bcm_enet_priv *priv,
-- u32 val, u32 off)
-+ u32 val, u32 off, int chan)
- {
-- bcm_writel(val, bcm_enet_shared_base[2] + off);
-+ bcm_writel(val, bcm_enet_shared_base[2] + (off + (chan * priv->dma_chan_width)));
- }
-
- /*
-@@ -270,7 +272,7 @@ static int bcm_enet_refill_rx(struct net
- len_stat = priv->rx_skb_size << DMADESC_LENGTH_SHIFT;
- len_stat |= DMADESC_OWNER_MASK;
- if (priv->rx_dirty_desc == priv->rx_ring_size - 1) {
-- len_stat |= DMADESC_WRAP_MASK;
-+ len_stat |= (DMADESC_WRAP_MASK >> priv->dma_desc_shift);
- priv->rx_dirty_desc = 0;
- } else {
- priv->rx_dirty_desc++;
-@@ -281,7 +283,10 @@ static int bcm_enet_refill_rx(struct net
- priv->rx_desc_count++;
-
- /* tell dma engine we allocated one buffer */
-- enet_dma_writel(priv, 1, ENETDMA_BUFALLOC_REG(priv->rx_chan));
-+ if (!priv->dma_no_sram)
-+ enet_dma_writel(priv, 1, ENETDMA_BUFALLOC_REG(priv->rx_chan));
-+ else
-+ enet_dmac_writel(priv, 1, ENETDMAC_BUFALLOC, priv->rx_chan);
- }
-
- /* If rx ring is still empty, set a timer to try allocating
-@@ -357,7 +362,8 @@ static int bcm_enet_receive_queue(struct
-
- /* if the packet does not have start of packet _and_
- * end of packet flag set, then just recycle it */
-- if ((len_stat & DMADESC_ESOP_MASK) != DMADESC_ESOP_MASK) {
-+ if ((len_stat & (DMADESC_ESOP_MASK >> priv->dma_desc_shift)) !=
-+ (DMADESC_ESOP_MASK >> priv->dma_desc_shift)) {
- dev->stats.rx_dropped++;
- continue;
- }
-@@ -418,8 +424,8 @@ static int bcm_enet_receive_queue(struct
- bcm_enet_refill_rx(dev);
-
- /* kick rx dma */
-- enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
-- ENETDMAC_CHANCFG_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, priv->dma_chan_en_mask,
-+ ENETDMAC_CHANCFG, priv->rx_chan);
- }
-
- return processed;
-@@ -494,10 +500,10 @@ static int bcm_enet_poll(struct napi_str
- dev = priv->net_dev;
-
- /* ack interrupts */
-- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IR_REG(priv->rx_chan));
-- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IR_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, priv->dma_chan_int_mask,
-+ ENETDMAC_IR, priv->rx_chan);
-+ enet_dmac_writel(priv, priv->dma_chan_int_mask,
-+ ENETDMAC_IR, priv->tx_chan);
-
- /* reclaim sent skb */
- tx_work_done = bcm_enet_tx_reclaim(dev, 0);
-@@ -516,10 +522,10 @@ static int bcm_enet_poll(struct napi_str
- napi_complete(napi);
-
- /* restore rx/tx interrupt */
-- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IRMASK_REG(priv->rx_chan));
-- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, priv->dma_chan_int_mask,
-+ ENETDMAC_IRMASK, priv->rx_chan);
-+ enet_dmac_writel(priv, priv->dma_chan_int_mask,
-+ ENETDMAC_IRMASK, priv->tx_chan);
-
- return rx_work_done;
- }
-@@ -562,8 +568,8 @@ static irqreturn_t bcm_enet_isr_dma(int
- priv = netdev_priv(dev);
-
- /* mask rx/tx interrupts */
-- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
-- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan);
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan);
-
- napi_schedule(&priv->napi);
-
-@@ -624,14 +630,14 @@ static int bcm_enet_start_xmit(struct sk
- DMA_TO_DEVICE);
-
- len_stat = (skb->len << DMADESC_LENGTH_SHIFT) & DMADESC_LENGTH_MASK;
-- len_stat |= DMADESC_ESOP_MASK |
-+ len_stat |= (DMADESC_ESOP_MASK >> priv->dma_desc_shift) |
- DMADESC_APPEND_CRC |
- DMADESC_OWNER_MASK;
-
- priv->tx_curr_desc++;
- if (priv->tx_curr_desc == priv->tx_ring_size) {
- priv->tx_curr_desc = 0;
-- len_stat |= DMADESC_WRAP_MASK;
-+ len_stat |= (DMADESC_WRAP_MASK >> priv->dma_desc_shift);
- }
- priv->tx_desc_count--;
-
-@@ -642,8 +648,8 @@ static int bcm_enet_start_xmit(struct sk
- wmb();
-
- /* kick tx dma */
-- enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
-- ENETDMAC_CHANCFG_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, priv->dma_chan_en_mask,
-+ ENETDMAC_CHANCFG, priv->tx_chan);
-
- /* stop queue if no more desc available */
- if (!priv->tx_desc_count)
-@@ -771,6 +777,9 @@ static void bcm_enet_set_flow(struct bcm
- val &= ~ENET_RXCFG_ENFLOW_MASK;
- enet_writel(priv, val, ENET_RXCFG_REG);
-
-+ if (priv->dma_no_sram)
-+ return;
-+
- /* tx flow control (pause frame generation) */
- val = enet_dma_readl(priv, ENETDMA_CFG_REG);
- if (tx_en)
-@@ -886,8 +895,8 @@ static int bcm_enet_open(struct net_devi
-
- /* mask all interrupts and request them */
- enet_writel(priv, 0, ENET_IRMASK_REG);
-- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
-- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan);
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan);
-
- ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev);
- if (ret)
-@@ -966,8 +975,12 @@ static int bcm_enet_open(struct net_devi
- priv->rx_curr_desc = 0;
-
- /* initialize flow control buffer allocation */
-- enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
-- ENETDMA_BUFALLOC_REG(priv->rx_chan));
-+ if (!priv->dma_no_sram)
-+ enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
-+ ENETDMA_BUFALLOC_REG(priv->rx_chan));
-+ else
-+ enet_dmac_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
-+ ENETDMAC_BUFALLOC, priv->rx_chan);
-
- if (bcm_enet_refill_rx(dev)) {
- dev_err(kdev, "cannot allocate rx skb queue\n");
-@@ -976,18 +989,30 @@ static int bcm_enet_open(struct net_devi
- }
-
- /* write rx & tx ring addresses */
-- enet_dmas_writel(priv, priv->rx_desc_dma,
-- ENETDMAS_RSTART_REG(priv->rx_chan));
-- enet_dmas_writel(priv, priv->tx_desc_dma,
-- ENETDMAS_RSTART_REG(priv->tx_chan));
-+ if (!priv->dma_no_sram) {
-+ enet_dmas_writel(priv, priv->rx_desc_dma,
-+ ENETDMAS_RSTART_REG, priv->rx_chan);
-+ enet_dmas_writel(priv, priv->tx_desc_dma,
-+ ENETDMAS_RSTART_REG, priv->tx_chan);
-+ } else {
-+ enet_dmac_writel(priv, priv->rx_desc_dma,
-+ ENETDMAC_RSTART, priv->rx_chan);
-+ enet_dmac_writel(priv, priv->tx_desc_dma,
-+ ENETDMAC_RSTART, priv->tx_chan);
-+ }
-
- /* clear remaining state ram for rx & tx channel */
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan));
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan));
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan));
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan));
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan));
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan));
-+ if (!priv->dma_no_sram) {
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->rx_chan);
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->tx_chan);
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->rx_chan);
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->tx_chan);
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->rx_chan);
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->tx_chan);
-+ } else {
-+ enet_dmac_writel(priv, 0, ENETDMAC_FC, priv->rx_chan);
-+ enet_dmac_writel(priv, 0, ENETDMAC_FC, priv->tx_chan);
-+ }
-
- /* set max rx/tx length */
- enet_writel(priv, priv->hw_mtu, ENET_RXMAXLEN_REG);
-@@ -995,18 +1020,24 @@ static int bcm_enet_open(struct net_devi
-
- /* set dma maximum burst len */
- enet_dmac_writel(priv, priv->dma_maxburst,
-- ENETDMAC_MAXBURST_REG(priv->rx_chan));
-+ ENETDMAC_MAXBURST, priv->rx_chan);
- enet_dmac_writel(priv, priv->dma_maxburst,
-- ENETDMAC_MAXBURST_REG(priv->tx_chan));
-+ ENETDMAC_MAXBURST, priv->tx_chan);
-
- /* set correct transmit fifo watermark */
- enet_writel(priv, BCMENET_TX_FIFO_TRESH, ENET_TXWMARK_REG);
-
- /* set flow control low/high threshold to 1/3 / 2/3 */
-- val = priv->rx_ring_size / 3;
-- enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan));
-- val = (priv->rx_ring_size * 2) / 3;
-- enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan));
-+ if (!priv->dma_no_sram) {
-+ val = priv->rx_ring_size / 3;
-+ enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan));
-+ val = (priv->rx_ring_size * 2) / 3;
-+ enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan));
-+ } else {
-+ enet_dmac_writel(priv, 5, ENETDMAC_FC, priv->rx_chan);
-+ enet_dmac_writel(priv, priv->rx_ring_size, ENETDMAC_LEN, priv->rx_chan);
-+ enet_dmac_writel(priv, priv->tx_ring_size, ENETDMAC_LEN, priv->tx_chan);
-+ }
-
- /* all set, enable mac and interrupts, start dma engine and
- * kick rx dma channel */
-@@ -1015,26 +1046,26 @@ static int bcm_enet_open(struct net_devi
- val |= ENET_CTL_ENABLE_MASK;
- enet_writel(priv, val, ENET_CTL_REG);
- enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG);
-- enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
-- ENETDMAC_CHANCFG_REG(priv->rx_chan));
-+ enet_dmac_writel(priv, priv->dma_chan_en_mask,
-+ ENETDMAC_CHANCFG, priv->rx_chan);
-
- /* watch "mib counters about to overflow" interrupt */
- enet_writel(priv, ENET_IR_MIB, ENET_IR_REG);
- enet_writel(priv, ENET_IR_MIB, ENET_IRMASK_REG);
-
- /* watch "packet transferred" interrupt in rx and tx */
-- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IR_REG(priv->rx_chan));
-- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IR_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, priv->dma_chan_int_mask,
-+ ENETDMAC_IR, priv->rx_chan);
-+ enet_dmac_writel(priv, priv->dma_chan_int_mask,
-+ ENETDMAC_IR, priv->tx_chan);
-
- /* make sure we enable napi before rx interrupt */
- napi_enable(&priv->napi);
-
-- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IRMASK_REG(priv->rx_chan));
-- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, priv->dma_chan_int_mask,
-+ ENETDMAC_IRMASK, priv->rx_chan);
-+ enet_dmac_writel(priv, priv->dma_chan_int_mask,
-+ ENETDMAC_IRMASK, priv->tx_chan);
-
- if (priv->has_phy)
- phy_start(priv->phydev);
-@@ -1111,13 +1142,13 @@ static void bcm_enet_disable_dma(struct
- {
- int limit;
-
-- enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG_REG(chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_CHANCFG, chan);
-
- limit = 1000;
- do {
- u32 val;
-
-- val = enet_dmac_readl(priv, ENETDMAC_CHANCFG_REG(chan));
-+ val = enet_dmac_readl(priv, ENETDMAC_CHANCFG, chan);
- if (!(val & ENETDMAC_CHANCFG_EN_MASK))
- break;
- udelay(1);
-@@ -1144,8 +1175,8 @@ static int bcm_enet_stop(struct net_devi
-
- /* mask all interrupts */
- enet_writel(priv, 0, ENET_IRMASK_REG);
-- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
-- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan);
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan);
-
- /* make sure no mib update is scheduled */
- cancel_work_sync(&priv->mib_update_task);
-@@ -1752,6 +1783,11 @@ static int bcm_enet_probe(struct platfor
- priv->pause_tx = pd->pause_tx;
- priv->force_duplex_full = pd->force_duplex_full;
- priv->force_speed_100 = pd->force_speed_100;
-+ priv->dma_chan_en_mask = pd->dma_chan_en_mask;
-+ priv->dma_chan_int_mask = pd->dma_chan_int_mask;
-+ priv->dma_chan_width = pd->dma_chan_width;
-+ priv->dma_no_sram = pd->dma_no_sram;
-+ priv->dma_desc_shift = pd->dma_desc_shift;
- }
-
- if (priv->mac_id == 0 && priv->has_phy && !priv->use_external_mii) {
-@@ -2123,8 +2159,8 @@ static int bcm_enetsw_open(struct net_de
- kdev = &priv->pdev->dev;
-
- /* mask all interrupts and request them */
-- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
-- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan);
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan);
-
- ret = request_irq(priv->irq_rx, bcm_enet_isr_dma,
- IRQF_DISABLED, dev->name, dev);
-@@ -2248,23 +2284,23 @@ static int bcm_enetsw_open(struct net_de
-
- /* write rx & tx ring addresses */
- enet_dmas_writel(priv, priv->rx_desc_dma,
-- ENETDMAS_RSTART_REG(priv->rx_chan));
-+ ENETDMAS_RSTART_REG, priv->rx_chan);
- enet_dmas_writel(priv, priv->tx_desc_dma,
-- ENETDMAS_RSTART_REG(priv->tx_chan));
-+ ENETDMAS_RSTART_REG, priv->tx_chan);
-
- /* clear remaining state ram for rx & tx channel */
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->rx_chan));
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG(priv->tx_chan));
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->rx_chan));
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG(priv->tx_chan));
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->rx_chan));
-- enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG(priv->tx_chan));
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->rx_chan);
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM2_REG, priv->tx_chan);
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->rx_chan);
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM3_REG, priv->tx_chan);
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->rx_chan);
-+ enet_dmas_writel(priv, 0, ENETDMAS_SRAM4_REG, priv->tx_chan);
-
- /* set dma maximum burst len */
- enet_dmac_writel(priv, priv->dma_maxburst,
-- ENETDMAC_MAXBURST_REG(priv->rx_chan));
-+ ENETDMAC_MAXBURST, priv->rx_chan);
- enet_dmac_writel(priv, priv->dma_maxburst,
-- ENETDMAC_MAXBURST_REG(priv->tx_chan));
-+ ENETDMAC_MAXBURST, priv->tx_chan);
-
- /* set flow control low/high threshold to 1/3 / 2/3 */
- val = priv->rx_ring_size / 3;
-@@ -2277,21 +2313,21 @@ static int bcm_enetsw_open(struct net_de
- wmb();
- enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG);
- enet_dmac_writel(priv, ENETDMAC_CHANCFG_EN_MASK,
-- ENETDMAC_CHANCFG_REG(priv->rx_chan));
-+ ENETDMAC_CHANCFG, priv->rx_chan);
-
- /* watch "packet transferred" interrupt in rx and tx */
- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IR_REG(priv->rx_chan));
-+ ENETDMAC_IR, priv->rx_chan);
- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IR_REG(priv->tx_chan));
-+ ENETDMAC_IR, priv->tx_chan);
-
- /* make sure we enable napi before rx interrupt */
- napi_enable(&priv->napi);
-
- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IRMASK_REG(priv->rx_chan));
-+ ENETDMAC_IRMASK, priv->rx_chan);
- enet_dmac_writel(priv, ENETDMAC_IR_PKTDONE_MASK,
-- ENETDMAC_IRMASK_REG(priv->tx_chan));
-+ ENETDMAC_IRMASK, priv->tx_chan);
-
- netif_carrier_on(dev);
- netif_start_queue(dev);
-@@ -2397,8 +2433,8 @@ static int bcm_enetsw_stop(struct net_de
- del_timer_sync(&priv->rx_timeout);
-
- /* mask all interrupts */
-- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->rx_chan));
-- enet_dmac_writel(priv, 0, ENETDMAC_IRMASK_REG(priv->tx_chan));
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->rx_chan);
-+ enet_dmac_writel(priv, 0, ENETDMAC_IRMASK, priv->tx_chan);
-
- /* disable dma & mac */
- bcm_enet_disable_dma(priv, priv->tx_chan);
-@@ -2736,6 +2772,9 @@ static int bcm_enetsw_probe(struct platf
- memcpy(priv->used_ports, pd->used_ports,
- sizeof (pd->used_ports));
- priv->num_ports = pd->num_ports;
-+ priv->dma_chan_en_mask = pd->dma_chan_en_mask;
-+ priv->dma_chan_int_mask = pd->dma_chan_int_mask;
-+ priv->dma_chan_width = pd->dma_chan_width;
- }
-
- ret = compute_hw_mtu(priv, dev->mtu);
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h
-@@ -339,6 +339,21 @@ struct bcm_enet_priv {
- /* used to poll switch port state */
- struct timer_list swphy_poll;
- spinlock_t enetsw_mdio_lock;
-+
-+ /* dma channel enable mask */
-+ u32 dma_chan_en_mask;
-+
-+ /* dma channel interrupt mask */
-+ u32 dma_chan_int_mask;
-+
-+ /* dma engine has *no* internal SRAM */
-+ unsigned int dma_no_sram;
-+
-+ /* dma channel width */
-+ unsigned int dma_chan_width;
-+
-+ /* dma descriptor shift value */
-+ unsigned int dma_desc_shift;
- };
-
- static inline int bcm_enet_port_is_rgmii(int portid)
+++ /dev/null
---- a/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
-@@ -2,6 +2,7 @@
- #define _PCI_ATH9K_FIXUP
-
-
--void pci_enable_ath9k_fixup(unsigned slot, u32 offset) __init;
-+void pci_enable_ath9k_fixup(unsigned slot, u32 offset,
-+ unsigned endian_check) __init;
-
- #endif /* _PCI_ATH9K_FIXUP */
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -19,6 +19,7 @@
- struct ath9k_caldata {
- unsigned int slot;
- u32 caldata_offset;
-+ unsigned int endian_check:1;
- };
-
- /*
---- a/arch/mips/bcm63xx/pci-ath9k-fixup.c
-+++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c
-@@ -172,12 +172,14 @@ static void ath9k_pci_fixup(struct pci_d
- }
- DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup);
-
--void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset)
-+void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset,
-+ unsigned endian_check)
- {
- if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups))
- return;
-
- ath9k_fixups[ath9k_num_fixups].slot = slot;
-+ ath9k_fixups[ath9k_num_fixups].pdata.endian_check = endian_check;
-
- if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset))
- return;
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -992,7 +992,8 @@ int __init board_register_devices(void)
-
- /* register any fixups */
- for (i = 0; i < board.has_caldata; i++)
-- pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset);
-+ pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset,
-+ board.caldata[i].endian_check);
-
- return 0;
- }
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -993,7 +993,7 @@ int __init board_register_devices(void)
- /* register any fixups */
- for (i = 0; i < board.has_caldata; i++)
- pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset,
-- board.caldata[i].endian_check);
-+ board.caldata[i].endian_check, board.caldata[i].led_pin);
-
- return 0;
- }
---- a/arch/mips/bcm63xx/pci-ath9k-fixup.c
-+++ b/arch/mips/bcm63xx/pci-ath9k-fixup.c
-@@ -173,13 +173,14 @@ static void ath9k_pci_fixup(struct pci_d
- DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATHEROS, PCI_ANY_ID, ath9k_pci_fixup);
-
- void __init pci_enable_ath9k_fixup(unsigned slot, u32 offset,
-- unsigned endian_check)
-+ unsigned endian_check, int led_pin)
- {
- if (ath9k_num_fixups >= ARRAY_SIZE(ath9k_fixups))
- return;
-
- ath9k_fixups[ath9k_num_fixups].slot = slot;
- ath9k_fixups[ath9k_num_fixups].pdata.endian_check = endian_check;
-+ ath9k_fixups[ath9k_num_fixups].pdata.led_pin = led_pin;
-
- if (!bcm63xx_read_eeprom(ath9k_fixups[ath9k_num_fixups].pdata.eeprom_data, offset))
- return;
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -20,6 +20,7 @@ struct ath9k_caldata {
- unsigned int slot;
- u32 caldata_offset;
- unsigned int endian_check:1;
-+ int led_pin;
- };
-
- /*
---- a/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/pci_ath9k_fixup.h
-@@ -3,6 +3,6 @@
-
-
- void pci_enable_ath9k_fixup(unsigned slot, u32 offset,
-- unsigned endian_check) __init;
-+ unsigned endian_check, int led_pin) __init;
-
- #endif /* _PCI_ATH9K_FIXUP */
+++ /dev/null
-From 5ed5b5e9614fa5b02da699ab565af76c7e63d64d Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Mon, 7 Jan 2013 17:45:39 +0100
-Subject: [PATCH 72/72] 446-BCM63XX-add-a-fixup-for-rt2x00-devices
-
----
- arch/mips/bcm63xx/Makefile | 2 +-
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 17 ++++-
- arch/mips/bcm63xx/dev-flash.c | 2 +-
- arch/mips/bcm63xx/pci-rt2x00-fixup.c | 71 ++++++++++++++++++++
- .../include/asm/mach-bcm63xx/bcm63xx_dev_flash.h | 2 +-
- .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 9 ++-
- .../include/asm/mach-bcm63xx/pci_rt2x00_fixup.h | 9 +++
- 7 files changed, 104 insertions(+), 8 deletions(-)
- create mode 100644 arch/mips/bcm63xx/pci-rt2x00-fixup.c
- create mode 100644 arch/mips/include/asm/mach-bcm63xx/pci_rt2x00_fixup.h
-
---- a/arch/mips/bcm63xx/Makefile
-+++ b/arch/mips/bcm63xx/Makefile
-@@ -2,7 +2,7 @@ obj-y += clk.o cpu.o cs.o gpio.o irq.o
- setup.o timer.o dev-dsp.o dev-enet.o dev-flash.o \
- dev-hsspi.o dev-pcmcia.o dev-rng.o dev-spi.o dev-uart.o \
- dev-wdt.o dev-usb-ehci.o dev-usb-ohci.o dev-usb-usbd.o \
-- pci-ath9k-fixup.o usb-common.o
-+ pci-ath9k-fixup.o pci-rt2x00-fixup.o usb-common.o
- obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
-
- obj-y += boards/
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -34,6 +34,7 @@
- #include <bcm63xx_dev_usb_usbd.h>
- #include <board_bcm963xx.h>
- #include <pci_ath9k_fixup.h>
-+#include <pci_rt2x00_fixup.h>
-
- #include <uapi/linux/bcm963xx_tag.h>
-
-@@ -991,9 +992,19 @@ int __init board_register_devices(void)
- }
-
- /* register any fixups */
-- for (i = 0; i < board.has_caldata; i++)
-- pci_enable_ath9k_fixup(board.caldata[i].slot, board.caldata[i].caldata_offset,
-- board.caldata[i].endian_check, board.caldata[i].led_pin);
-+ for (i = 0; i < board.has_caldata; i++) {
-+ switch (board.caldata[i].vendor) {
-+ case PCI_VENDOR_ID_ATHEROS:
-+ pci_enable_ath9k_fixup(board.caldata[i].slot,
-+ board.caldata[i].caldata_offset, board.caldata[i].endian_check,
-+ board.caldata[i].led_pin);
-+ break;
-+ case PCI_VENDOR_ID_RALINK:
-+ pci_enable_rt2x00_fixup(board.caldata[i].slot,
-+ board.caldata[i].eeprom);
-+ break;
-+ }
-+ }
-
- return 0;
- }
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -141,7 +141,7 @@ static int __init bcm63xx_detect_flash_t
- return 0;
- }
-
--int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata)
-+int __init bcm63xx_flash_register(int num_caldata, struct bcm63xx_caldata *caldata)
- {
- u32 val;
- unsigned int i;
---- /dev/null
-+++ b/arch/mips/bcm63xx/pci-rt2x00-fixup.c
-@@ -0,0 +1,72 @@
-+/*
-+ * Broadcom BCM63XX RT2x00 EEPROM fixup helper.
-+ *
-+ * Copyright (C) 2012 Álvaro Fernández Rojas <noltari@gmail.com>
-+ *
-+ * Based on
-+ *
-+ * Broadcom BCM63XX Ath9k EEPROM fixup helper.
-+ *
-+ * Copyright (C) 2012 Jonas Gorski <jonas.gorski@gmail.com>
-+ *
-+ * This program is free software; you can redistribute it and/or modify it
-+ * under the terms of the GNU General Public License version 2 as published
-+ * by the Free Software Foundation.
-+ */
-+
-+#include <linux/if_ether.h>
-+#include <linux/pci.h>
-+#include <linux/platform_device.h>
-+#include <linux/rt2x00_platform.h>
-+
-+#include <bcm63xx_nvram.h>
-+#include <pci_rt2x00_fixup.h>
-+
-+struct rt2x00_fixup {
-+ unsigned slot;
-+ u8 mac[ETH_ALEN];
-+ struct rt2x00_platform_data pdata;
-+};
-+
-+static int rt2x00_num_fixups;
-+static struct rt2x00_fixup rt2x00_fixups[2] = {
-+ {
-+ .slot = 255,
-+ },
-+ {
-+ .slot = 255,
-+ },
-+};
-+
-+static void rt2x00_pci_fixup(struct pci_dev *dev)
-+{
-+ unsigned i;
-+ struct rt2x00_platform_data *pdata = NULL;
-+
-+ for (i = 0; i < rt2x00_num_fixups; i++) {
-+ if (rt2x00_fixups[i].slot != PCI_SLOT(dev->devfn))
-+ continue;
-+
-+ pdata = &rt2x00_fixups[i].pdata;
-+ break;
-+ }
-+
-+ dev->dev.platform_data = pdata;
-+}
-+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_RALINK, PCI_ANY_ID, rt2x00_pci_fixup);
-+
-+void __init pci_enable_rt2x00_fixup(unsigned slot, char* eeprom)
-+{
-+ if (rt2x00_num_fixups >= ARRAY_SIZE(rt2x00_fixups))
-+ return;
-+
-+ rt2x00_fixups[rt2x00_num_fixups].slot = slot;
-+ rt2x00_fixups[rt2x00_num_fixups].pdata.eeprom_file_name = kstrdup(eeprom, GFP_KERNEL);
-+
-+ if (bcm63xx_nvram_get_mac_address(rt2x00_fixups[rt2x00_num_fixups].mac))
-+ return;
-+
-+ rt2x00_fixups[rt2x00_num_fixups].pdata.mac_address = rt2x00_fixups[rt2x00_num_fixups].mac;
-+ rt2x00_num_fixups++;
-+}
-+
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_dev_flash.h
-@@ -11,6 +11,6 @@ enum {
-
- extern int bcm63xx_attached_flash;
-
--int __init bcm63xx_flash_register(int num_caldata, struct ath9k_caldata *caldata);
-+int __init bcm63xx_flash_register(int num_caldata, struct bcm63xx_caldata *caldata);
-
- #endif /* __BCM63XX_FLASH_H */
---- a/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/board_bcm963xx.h
-@@ -9,6 +9,7 @@
- #include <bcm63xx_dev_usb_usbd.h>
- #include <bcm63xx_dev_dsp.h>
- #include <pci_ath9k_fixup.h>
-+#include <pci_rt2x00_fixup.h>
-
- /*
- * flash mapping
-@@ -16,11 +17,15 @@
- #define BCM963XX_CFE_VERSION_OFFSET 0x570
- #define BCM963XX_NVRAM_OFFSET 0x580
-
--struct ath9k_caldata {
-+struct bcm63xx_caldata {
-+ unsigned int vendor;
- unsigned int slot;
- u32 caldata_offset;
-+ /* Atheros */
- unsigned int endian_check:1;
- int led_pin;
-+ /* Ralink */
-+ char* eeprom;
- };
-
- /*
-@@ -45,7 +50,7 @@ struct board_info {
- unsigned int has_caldata:2;
-
- /* wifi calibration data config */
-- struct ath9k_caldata caldata[2];
-+ struct bcm63xx_caldata caldata[2];
-
- /* ethernet config */
- struct bcm63xx_enet_platform_data enet0;
---- /dev/null
-+++ b/arch/mips/include/asm/mach-bcm63xx/pci_rt2x00_fixup.h
-@@ -0,0 +1,9 @@
-+#ifndef _PCI_RT2X00_FIXUP
-+#define _PCI_RT2X00_FIXUP
-+
-+#define PCI_VENDOR_ID_RALINK 0x1814
-+
-+void pci_enable_rt2x00_fixup(unsigned slot, char* eeprom) __init;
-+
-+#endif /* _PCI_RT2X00_FIXUP */
-+
+++ /dev/null
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.h
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.h
-@@ -336,6 +336,9 @@ struct bcm_enet_priv {
- struct bcm63xx_enetsw_port used_ports[ENETSW_MAX_PORT];
- int sw_port_link[ENETSW_MAX_PORT];
-
-+ /* platform device for associated switch */
-+ struct platform_device *b53_device;
-+
- /* used to poll switch port state */
- struct timer_list swphy_poll;
- spinlock_t enetsw_mdio_lock;
---- a/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-+++ b/drivers/net/ethernet/broadcom/bcm63xx_enet.c
-@@ -30,6 +30,7 @@
- #include <linux/dma-mapping.h>
- #include <linux/platform_device.h>
- #include <linux/if_vlan.h>
-+#include <linux/platform_data/b53.h>
-
- #include <bcm63xx_dev_enet.h>
- #include "bcm63xx_enet.h"
-@@ -1992,7 +1993,8 @@ static int bcm_enet_remove(struct platfo
- return 0;
- }
-
--struct platform_driver bcm63xx_enet_driver = {
-+
-+static struct platform_driver bcm63xx_enet_driver = {
- .probe = bcm_enet_probe,
- .remove = bcm_enet_remove,
- .driver = {
-@@ -2001,6 +2003,42 @@ struct platform_driver bcm63xx_enet_driv
- },
- };
-
-+struct b53_platform_data bcm63xx_b53_pdata = {
-+ .chip_id = 0x6300,
-+ .big_endian = 1,
-+};
-+
-+struct platform_device bcm63xx_b53_dev = {
-+ .name = "b53-switch",
-+ .id = -1,
-+ .dev = {
-+ .platform_data = &bcm63xx_b53_pdata,
-+ },
-+};
-+
-+static int bcmenet_switch_register(struct bcm_enet_priv *priv, u16 port_mask)
-+{
-+ int ret;
-+
-+ bcm63xx_b53_pdata.regs = priv->base;
-+ bcm63xx_b53_pdata.enabled_ports = port_mask;
-+ bcm63xx_b53_pdata.alias = priv->net_dev->name;
-+
-+ ret = platform_device_register(&bcm63xx_b53_dev);
-+ if (!ret)
-+ priv->b53_device = &bcm63xx_b53_dev;
-+
-+ return ret;
-+}
-+
-+static void bcmenet_switch_unregister(struct bcm_enet_priv *priv)
-+{
-+ if (priv->b53_device)
-+ platform_device_unregister(&bcm63xx_b53_dev);
-+
-+ priv->b53_device = NULL;
-+}
-+
- /*
- * switch mii access callbacks
- */
-@@ -2249,29 +2287,6 @@ static int bcm_enetsw_open(struct net_de
- enetsw_writeb(priv, rgmii_ctrl, ENETSW_RGMII_CTRL_REG(i));
- }
-
-- /* reset mib */
-- val = enetsw_readb(priv, ENETSW_GMCR_REG);
-- val |= ENETSW_GMCR_RST_MIB_MASK;
-- enetsw_writeb(priv, val, ENETSW_GMCR_REG);
-- mdelay(1);
-- val &= ~ENETSW_GMCR_RST_MIB_MASK;
-- enetsw_writeb(priv, val, ENETSW_GMCR_REG);
-- mdelay(1);
--
-- /* force CPU port state */
-- val = enetsw_readb(priv, ENETSW_IMPOV_REG);
-- val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK;
-- enetsw_writeb(priv, val, ENETSW_IMPOV_REG);
--
-- /* enable switch forward engine */
-- val = enetsw_readb(priv, ENETSW_SWMODE_REG);
-- val |= ENETSW_SWMODE_FWD_EN_MASK;
-- enetsw_writeb(priv, val, ENETSW_SWMODE_REG);
--
-- /* enable jumbo on all ports */
-- enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG);
-- enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG);
--
- /* initialize flow control buffer allocation */
- enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0,
- ENETDMA_BUFALLOC_REG(priv->rx_chan));
-@@ -2739,6 +2754,9 @@ static int bcm_enetsw_probe(struct platf
- struct bcm63xx_enetsw_platform_data *pd;
- struct resource *res_mem;
- int ret, irq_rx, irq_tx;
-+ unsigned i, num_ports = 0;
-+ u16 port_mask = BIT(8);
-+ u8 val;
-
- /* stop if shared driver failed, assume driver->probe will be
- * called in the same order we register devices (correct ?) */
-@@ -2826,6 +2844,43 @@ static int bcm_enetsw_probe(struct platf
- priv->pdev = pdev;
- priv->net_dev = dev;
-
-+ /* reset mib */
-+ val = enetsw_readb(priv, ENETSW_GMCR_REG);
-+ val |= ENETSW_GMCR_RST_MIB_MASK;
-+ enetsw_writeb(priv, val, ENETSW_GMCR_REG);
-+ mdelay(1);
-+ val &= ~ENETSW_GMCR_RST_MIB_MASK;
-+ enetsw_writeb(priv, val, ENETSW_GMCR_REG);
-+ mdelay(1);
-+
-+ /* force CPU port state */
-+ val = enetsw_readb(priv, ENETSW_IMPOV_REG);
-+ val |= ENETSW_IMPOV_FORCE_MASK | ENETSW_IMPOV_LINKUP_MASK;
-+ enetsw_writeb(priv, val, ENETSW_IMPOV_REG);
-+
-+ /* enable switch forward engine */
-+ val = enetsw_readb(priv, ENETSW_SWMODE_REG);
-+ val |= ENETSW_SWMODE_FWD_EN_MASK;
-+ enetsw_writeb(priv, val, ENETSW_SWMODE_REG);
-+
-+ /* enable jumbo on all ports */
-+ enetsw_writel(priv, 0x1ff, ENETSW_JMBCTL_PORT_REG);
-+ enetsw_writew(priv, 9728, ENETSW_JMBCTL_MAXSIZE_REG);
-+
-+ for (i = 0; i < priv->num_ports; i++) {
-+ struct bcm63xx_enetsw_port *port = &priv->used_ports[i];
-+
-+ if (!port->used)
-+ continue;
-+
-+ num_ports++;
-+ port_mask |= BIT(i);
-+ }
-+
-+ /* only register if there is more than one external port */
-+ if (num_ports > 1)
-+ bcmenet_switch_register(priv, port_mask);
-+
- return 0;
-
- out_put_clk:
-@@ -2856,6 +2911,9 @@ static int bcm_enetsw_remove(struct plat
- priv = netdev_priv(dev);
- unregister_netdev(dev);
-
-+ /* remove switch */
-+ bcmenet_switch_unregister(priv);
-+
- /* release device resources */
- iounmap(priv->base);
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+++ /dev/null
---- a/arch/mips/bcm63xx/Kconfig
-+++ b/arch/mips/bcm63xx/Kconfig
-@@ -13,6 +13,10 @@ config BCM63XX_EHCI
- select USB_EHCI_BIG_ENDIAN_DESC if USB_EHCI_HCD
- select USB_EHCI_BIG_ENDIAN_MMIO if USB_EHCI_HCD
-
-+config BCM63XX_CPU_3368
-+ bool "support 3368 CPU"
-+ select HW_HAS_PCI
-+
- config BCM63XX_CPU_6328
- bool "support 6328 CPU"
- select HW_HAS_PCI
---- a/arch/mips/bcm63xx/cpu.c
-+++ b/arch/mips/bcm63xx/cpu.c
-@@ -29,6 +29,14 @@ static u8 bcm63xx_cpu_rev;
- static unsigned int bcm63xx_cpu_freq;
- static unsigned int bcm63xx_memory_size;
-
-+static const unsigned long bcm3368_regs_base[] = {
-+ __GEN_CPU_REGS_TABLE(3368)
-+};
-+
-+static const int bcm3368_irqs[] = {
-+ __GEN_CPU_IRQ_TABLE(3368)
-+};
-+
- static const unsigned long bcm6328_regs_base[] = {
- __GEN_CPU_REGS_TABLE(6328)
- };
-@@ -116,6 +124,9 @@ unsigned int bcm63xx_get_memory_size(voi
- static unsigned int detect_cpu_clock(void)
- {
- switch (bcm63xx_get_cpu_id()) {
-+ case BCM3368_CPU_ID:
-+ return 300000000;
-+
- case BCM6328_CPU_ID:
- {
- unsigned int tmp, mips_pll_fcvo;
-@@ -266,7 +277,7 @@ static unsigned int detect_memory_size(v
- banks = (val & SDRAM_CFG_BANK_MASK) ? 2 : 1;
- }
-
-- if (BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
-+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6368()) {
- val = bcm_memc_readl(MEMC_CFG_REG);
- rows = (val & MEMC_CFG_ROW_MASK) >> MEMC_CFG_ROW_SHIFT;
- cols = (val & MEMC_CFG_COL_MASK) >> MEMC_CFG_COL_SHIFT;
-@@ -302,10 +313,17 @@ void __init bcm63xx_cpu_init(void)
- chipid_reg = BCM_6345_PERF_BASE;
- break;
- case CPU_BMIPS4350:
-- if ((read_c0_prid() & 0xf0) == 0x10)
-+ switch ((read_c0_prid() & 0xff)) {
-+ case 0x04:
-+ chipid_reg = BCM_3368_PERF_BASE;
-+ break;
-+ case 0x10:
- chipid_reg = BCM_6345_PERF_BASE;
-- else
-+ break;
-+ default:
- chipid_reg = BCM_6368_PERF_BASE;
-+ break;
-+ }
- break;
- }
-
-@@ -322,6 +340,10 @@ void __init bcm63xx_cpu_init(void)
- bcm63xx_cpu_rev = (tmp & REV_REVID_MASK) >> REV_REVID_SHIFT;
-
- switch (bcm63xx_cpu_id) {
-+ case BCM3368_CPU_ID:
-+ bcm63xx_regs_base = bcm3368_regs_base;
-+ bcm63xx_irqs = bcm3368_irqs;
-+ break;
- case BCM6328_CPU_ID:
- bcm63xx_regs_base = bcm6328_regs_base;
- bcm63xx_irqs = bcm6328_irqs;
---- a/arch/mips/bcm63xx/dev-uart.c
-+++ b/arch/mips/bcm63xx/dev-uart.c
-@@ -54,8 +54,8 @@ int __init bcm63xx_uart_register(unsigne
- if (id >= ARRAY_SIZE(bcm63xx_uart_devices))
- return -ENODEV;
-
-- if (id == 1 && !BCMCPU_IS_6328() && !BCMCPU_IS_6358() &&
-- !BCMCPU_IS_6368())
-+ if (id == 1 && !BCMCPU_IS_3368() && !BCMCPU_IS_6328() &&
-+ !BCMCPU_IS_6358() && !BCMCPU_IS_6368())
- return -ENODEV;
-
- if (id == 0) {
---- a/arch/mips/bcm63xx/prom.c
-+++ b/arch/mips/bcm63xx/prom.c
-@@ -30,7 +30,9 @@ void __init prom_init(void)
- bcm_wdt_writel(WDT_STOP_2, WDT_CTL_REG);
-
- /* disable all hardware blocks clock for now */
-- if (BCMCPU_IS_6328())
-+ if (BCMCPU_IS_3368())
-+ mask = CKCTL_3368_ALL_SAFE_EN;
-+ else if (BCMCPU_IS_6328())
- mask = CKCTL_6328_ALL_SAFE_EN;
- else if (BCMCPU_IS_6338())
- mask = CKCTL_6338_ALL_SAFE_EN;
---- a/arch/mips/bcm63xx/setup.c
-+++ b/arch/mips/bcm63xx/setup.c
-@@ -68,6 +68,9 @@ void bcm63xx_machine_reboot(void)
-
- /* mask and clear all external irq */
- switch (bcm63xx_get_cpu_id()) {
-+ case BCM3368_CPU_ID:
-+ perf_regs[0] = PERF_EXTIRQ_CFG_REG_3368;
-+ break;
- case BCM6328_CPU_ID:
- perf_regs[0] = PERF_EXTIRQ_CFG_REG_6328;
- break;
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_cpu.h
-@@ -9,6 +9,7 @@
- * compile time if only one CPU support is enabled (idea stolen from
- * arm mach-types)
- */
-+#define BCM3368_CPU_ID 0x3368
- #define BCM6328_CPU_ID 0x6328
- #define BCM6338_CPU_ID 0x6338
- #define BCM6345_CPU_ID 0x6345
-@@ -22,6 +23,19 @@ u16 __bcm63xx_get_cpu_id(void);
- u8 bcm63xx_get_cpu_rev(void);
- unsigned int bcm63xx_get_cpu_freq(void);
-
-+#ifdef CONFIG_BCM63XX_CPU_3368
-+# ifdef bcm63xx_get_cpu_id
-+# undef bcm63xx_get_cpu_id
-+# define bcm63xx_get_cpu_id() __bcm63xx_get_cpu_id()
-+# define BCMCPU_RUNTIME_DETECT
-+# else
-+# define bcm63xx_get_cpu_id() BCM3368_CPU_ID
-+# endif
-+# define BCMCPU_IS_3368() (bcm63xx_get_cpu_id() == BCM3368_CPU_ID)
-+#else
-+# define BCMCPU_IS_3368() (0)
-+#endif
-+
- #ifdef CONFIG_BCM63XX_CPU_6328
- # ifdef bcm63xx_get_cpu_id
- # undef bcm63xx_get_cpu_id
-@@ -196,6 +210,53 @@ enum bcm63xx_regs_set {
- #define RSET_RNG_SIZE 20
-
- /*
-+ * 3368 register sets base address
-+ */
-+#define BCM_3368_DSL_LMEM_BASE (0xdeadbeef)
-+#define BCM_3368_PERF_BASE (0xfff8c000)
-+#define BCM_3368_TIMER_BASE (0xfff8c040)
-+#define BCM_3368_WDT_BASE (0xfff8c080)
-+#define BCM_3368_UART0_BASE (0xfff8c100)
-+#define BCM_3368_UART1_BASE (0xfff8c120)
-+#define BCM_3368_GPIO_BASE (0xfff8c080)
-+#define BCM_3368_SPI_BASE (0xfff8c800)
-+#define BCM_3368_HSSPI_BASE (0xdeadbeef)
-+#define BCM_3368_UDC0_BASE (0xdeadbeef)
-+#define BCM_3368_USBDMA_BASE (0xdeadbeef)
-+#define BCM_3368_OHCI0_BASE (0xdeadbeef)
-+#define BCM_3368_OHCI_PRIV_BASE (0xdeadbeef)
-+#define BCM_3368_USBH_PRIV_BASE (0xdeadbeef)
-+#define BCM_3368_USBD_BASE (0xdeadbeef)
-+#define BCM_3368_MPI_BASE (0xfff80000)
-+#define BCM_3368_PCMCIA_BASE (0xfff80054)
-+#define BCM_3368_PCIE_BASE (0xdeadbeef)
-+#define BCM_3368_SDRAM_REGS_BASE (0xdeadbeef)
-+#define BCM_3368_DSL_BASE (0xdeadbeef)
-+#define BCM_3368_UBUS_BASE (0xdeadbeef)
-+#define BCM_3368_ENET0_BASE (0xfff98000)
-+#define BCM_3368_ENET1_BASE (0xfff98800)
-+#define BCM_3368_ENETDMA_BASE (0xfff99800)
-+#define BCM_3368_ENETDMAC_BASE (0xfff99900)
-+#define BCM_3368_ENETDMAS_BASE (0xfff99a00)
-+#define BCM_3368_ENETSW_BASE (0xdeadbeef)
-+#define BCM_3368_EHCI0_BASE (0xdeadbeef)
-+#define BCM_3368_SDRAM_BASE (0xdeadbeef)
-+#define BCM_3368_MEMC_BASE (0xfff84000)
-+#define BCM_3368_DDR_BASE (0xdeadbeef)
-+#define BCM_3368_M2M_BASE (0xdeadbeef)
-+#define BCM_3368_ATM_BASE (0xdeadbeef)
-+#define BCM_3368_XTM_BASE (0xdeadbeef)
-+#define BCM_3368_XTMDMA_BASE (0xdeadbeef)
-+#define BCM_3368_XTMDMAC_BASE (0xdeadbeef)
-+#define BCM_3368_XTMDMAS_BASE (0xdeadbeef)
-+#define BCM_3368_PCM_BASE (0xfff9c200)
-+#define BCM_3368_PCMDMA_BASE (0xdeadbeef)
-+#define BCM_3368_PCMDMAC_BASE (0xdeadbeef)
-+#define BCM_3368_PCMDMAS_BASE (0xdeadbeef)
-+#define BCM_3368_RNG_BASE (0xdeadbeef)
-+#define BCM_3368_MISC_BASE (0xdeadbeef)
-+
-+/*
- * 6328 register sets base address
- */
- #define BCM_6328_DSL_LMEM_BASE (0xdeadbeef)
-@@ -633,6 +694,9 @@ static inline unsigned long bcm63xx_regs
- #ifdef BCMCPU_RUNTIME_DETECT
- return bcm63xx_regs_base[set];
- #else
-+#ifdef CONFIG_BCM63XX_CPU_3368
-+ __GEN_RSET(3368)
-+#endif
- #ifdef CONFIG_BCM63XX_CPU_6328
- __GEN_RSET(6328)
- #endif
-@@ -701,6 +765,52 @@ enum bcm63xx_irq {
- };
-
- /*
-+ * 3368 irqs
-+ */
-+#define BCM_3368_TIMER_IRQ (IRQ_INTERNAL_BASE + 0)
-+#define BCM_3368_SPI_IRQ (IRQ_INTERNAL_BASE + 1)
-+#define BCM_3368_UART0_IRQ (IRQ_INTERNAL_BASE + 2)
-+#define BCM_3368_UART1_IRQ (IRQ_INTERNAL_BASE + 3)
-+#define BCM_3368_DSL_IRQ 0
-+#define BCM_3368_UDC0_IRQ 0
-+#define BCM_3368_OHCI0_IRQ 0
-+#define BCM_3368_ENET0_IRQ (IRQ_INTERNAL_BASE + 8)
-+#define BCM_3368_ENET1_IRQ (IRQ_INTERNAL_BASE + 6)
-+#define BCM_3368_ENET_PHY_IRQ (IRQ_INTERNAL_BASE + 9)
-+#define BCM_3368_ENET0_RXDMA_IRQ (IRQ_INTERNAL_BASE + 15)
-+#define BCM_3368_ENET0_TXDMA_IRQ (IRQ_INTERNAL_BASE + 16)
-+#define BCM_3368_HSSPI_IRQ 0
-+#define BCM_3368_EHCI0_IRQ 0
-+#define BCM_3368_USBD_IRQ 0
-+#define BCM_3368_USBD_RXDMA0_IRQ 0
-+#define BCM_3368_USBD_TXDMA0_IRQ 0
-+#define BCM_3368_USBD_RXDMA1_IRQ 0
-+#define BCM_3368_USBD_TXDMA1_IRQ 0
-+#define BCM_3368_USBD_RXDMA2_IRQ 0
-+#define BCM_3368_USBD_TXDMA2_IRQ 0
-+#define BCM_3368_ENET1_RXDMA_IRQ (IRQ_INTERNAL_BASE + 17)
-+#define BCM_3368_ENET1_TXDMA_IRQ (IRQ_INTERNAL_BASE + 18)
-+#define BCM_3368_PCI_IRQ (IRQ_INTERNAL_BASE + 31)
-+#define BCM_3368_PCMCIA_IRQ 0
-+#define BCM_3368_ATM_IRQ 0
-+#define BCM_3368_ENETSW_RXDMA0_IRQ 0
-+#define BCM_3368_ENETSW_RXDMA1_IRQ 0
-+#define BCM_3368_ENETSW_RXDMA2_IRQ 0
-+#define BCM_3368_ENETSW_RXDMA3_IRQ 0
-+#define BCM_3368_ENETSW_TXDMA0_IRQ 0
-+#define BCM_3368_ENETSW_TXDMA1_IRQ 0
-+#define BCM_3368_ENETSW_TXDMA2_IRQ 0
-+#define BCM_3368_ENETSW_TXDMA3_IRQ 0
-+#define BCM_3368_XTM_IRQ 0
-+#define BCM_3368_XTM_DMA0_IRQ 0
-+
-+#define BCM_3368_EXT_IRQ0 (IRQ_INTERNAL_BASE + 25)
-+#define BCM_3368_EXT_IRQ1 (IRQ_INTERNAL_BASE + 26)
-+#define BCM_3368_EXT_IRQ2 (IRQ_INTERNAL_BASE + 27)
-+#define BCM_3368_EXT_IRQ3 (IRQ_INTERNAL_BASE + 28)
-+
-+
-+/*
- * 6328 irqs
- */
- #define BCM_6328_HIGH_IRQ_BASE (IRQ_INTERNAL_BASE + 32)
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_gpio.h
-@@ -11,6 +11,7 @@ static inline unsigned long bcm63xx_gpio
- switch (bcm63xx_get_cpu_id()) {
- case BCM6328_CPU_ID:
- return 32;
-+ case BCM3368_CPU_ID:
- case BCM6358_CPU_ID:
- return 40;
- case BCM6338_CPU_ID:
---- a/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/bcm63xx_regs.h
-@@ -15,6 +15,39 @@
- /* Clock Control register */
- #define PERF_CKCTL_REG 0x4
-
-+#define CKCTL_3368_MAC_EN (1 << 3)
-+#define CKCTL_3368_TC_EN (1 << 5)
-+#define CKCTL_3368_US_TOP_EN (1 << 6)
-+#define CKCTL_3368_DS_TOP_EN (1 << 7)
-+#define CKCTL_3368_APM_EN (1 << 8)
-+#define CKCTL_3368_SPI_EN (1 << 9)
-+#define CKCTL_3368_USBS_EN (1 << 10)
-+#define CKCTL_3368_BMU_EN (1 << 11)
-+#define CKCTL_3368_PCM_EN (1 << 12)
-+#define CKCTL_3368_NTP_EN (1 << 13)
-+#define CKCTL_3368_ACP_B_EN (1 << 14)
-+#define CKCTL_3368_ACP_A_EN (1 << 15)
-+#define CKCTL_3368_EMUSB_EN (1 << 17)
-+#define CKCTL_3368_ENET0_EN (1 << 18)
-+#define CKCTL_3368_ENET1_EN (1 << 19)
-+#define CKCTL_3368_USBU_EN (1 << 20)
-+#define CKCTL_3368_EPHY_EN (1 << 21)
-+
-+#define CKCTL_3368_ALL_SAFE_EN (CKCTL_3368_MAC_EN | \
-+ CKCTL_3368_TC_EN | \
-+ CKCTL_3368_US_TOP_EN | \
-+ CKCTL_3368_DS_TOP_EN | \
-+ CKCTL_3368_APM_EN | \
-+ CKCTL_3368_SPI_EN | \
-+ CKCTL_3368_USBS_EN | \
-+ CKCTL_3368_BMU_EN | \
-+ CKCTL_3368_PCM_EN | \
-+ CKCTL_3368_NTP_EN | \
-+ CKCTL_3368_ACP_B_EN | \
-+ CKCTL_3368_ACP_A_EN | \
-+ CKCTL_3368_EMUSB_EN | \
-+ CKCTL_3368_USBU_EN)
-+
- #define CKCTL_6328_PHYMIPS_EN (1 << 0)
- #define CKCTL_6328_ADSL_QPROC_EN (1 << 1)
- #define CKCTL_6328_ADSL_AFE_EN (1 << 2)
-@@ -181,6 +214,7 @@
- #define SYS_PLL_SOFT_RESET 0x1
-
- /* Interrupt Mask register */
-+#define PERF_IRQMASK_3368_REG 0xc
- #define PERF_IRQMASK_6328_REG(x) (0x20 + (x) * 0x10)
- #define PERF_IRQMASK_6338_REG 0xc
- #define PERF_IRQMASK_6345_REG 0xc
-@@ -190,6 +224,7 @@
- #define PERF_IRQMASK_6368_REG(x) (0x20 + (x) * 0x10)
-
- /* Interrupt Status register */
-+#define PERF_IRQSTAT_3368_REG 0x10
- #define PERF_IRQSTAT_6328_REG(x) (0x28 + (x) * 0x10)
- #define PERF_IRQSTAT_6338_REG 0x10
- #define PERF_IRQSTAT_6345_REG 0x10
-@@ -199,6 +234,7 @@
- #define PERF_IRQSTAT_6368_REG(x) (0x28 + (x) * 0x10)
-
- /* External Interrupt Configuration register */
-+#define PERF_EXTIRQ_CFG_REG_3368 0x14
- #define PERF_EXTIRQ_CFG_REG_6328 0x18
- #define PERF_EXTIRQ_CFG_REG_6338 0x14
- #define PERF_EXTIRQ_CFG_REG_6345 0x14
-@@ -1386,7 +1422,7 @@
- #define SPI_6348_RX_DATA 0x80
- #define SPI_6348_RX_DATA_SIZE 0x3f
-
--/* BCM 6358/6262/6368 SPI core */
-+/* BCM 3368/6358/6262/6368 SPI core */
- #define SPI_6358_MSG_CTL 0x00 /* 16-bits register */
- #define SPI_6358_MSG_CTL_WIDTH 16
- #define SPI_6358_MSG_DATA 0x02
---- a/arch/mips/include/asm/mach-bcm63xx/ioremap.h
-+++ b/arch/mips/include/asm/mach-bcm63xx/ioremap.h
-@@ -11,6 +11,10 @@ static inline phys_t fixup_bigphys_addr(
- static inline int is_bcm63xx_internal_registers(phys_t offset)
- {
- switch (bcm63xx_get_cpu_id()) {
-+ case BCM3368_CPU_ID:
-+ if (offset >= 0xfff80000)
-+ return 1;
-+ break;
- case BCM6338_CPU_ID:
- case BCM6345_CPU_ID:
- case BCM6348_CPU_ID:
---- a/arch/mips/bcm63xx/irq.c
-+++ b/arch/mips/bcm63xx/irq.c
-@@ -33,6 +33,19 @@ static DEFINE_SPINLOCK(ipic_lock);
- static DEFINE_SPINLOCK(epic_lock);
-
- #ifndef BCMCPU_RUNTIME_DETECT
-+#ifdef CONFIG_BCM63XX_CPU_3368
-+#define irq_stat_reg0 PERF_IRQSTAT_3368_REG
-+#define irq_mask_reg0 PERF_IRQMASK_3368_REG
-+#define irq_stat_reg1 0
-+#define irq_mask_reg1 0
-+#define irq_bits 32
-+#define is_ext_irq_cascaded 0
-+#define ext_irq_start 0
-+#define ext_irq_end 0
-+#define ext_irq_count 4
-+#define ext_irq_cfg_reg1 PERF_EXTIRQ_CFG_REG_3368
-+#define ext_irq_cfg_reg2 0
-+#endif
- #ifdef CONFIG_BCM63XX_CPU_6328
- #define irq_stat_reg0 PERF_IRQSTAT_6328_REG(0)
- #define irq_mask_reg0 PERF_IRQMASK_6328_REG(0)
-@@ -165,6 +178,13 @@ static void bcm63xx_init_irq(void)
- irq_mask_addr1 = bcm63xx_regset_address(RSET_PERF);
-
- switch (bcm63xx_get_cpu_id()) {
-+ case BCM3368_CPU_ID:
-+ irq_stat_addr0 += PERF_IRQSTAT_3368_REG;
-+ irq_mask_addr0 += PERF_IRQMASK_3368_REG;
-+ irq_bits = 32;
-+ ext_irq_count = 4;
-+ ext_irq_cfg_reg1 = PERF_EXTIRQ_CFG_REG_3368;
-+ break;
- case BCM6328_CPU_ID:
- irq_stat_addr0 += PERF_IRQSTAT_6328_REG(0);
- irq_mask_addr0 += PERF_IRQMASK_6328_REG(0);
---- a/arch/mips/bcm63xx/dev-spi.c
-+++ b/arch/mips/bcm63xx/dev-spi.c
-@@ -37,7 +37,7 @@ static __init void bcm63xx_spi_regs_init
- {
- if (BCMCPU_IS_6338() || BCMCPU_IS_6348())
- bcm63xx_regs_spi = bcm6348_regs_spi;
-- if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368())
-+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368())
- bcm63xx_regs_spi = bcm6358_regs_spi;
- }
- #else
-@@ -87,7 +87,8 @@ int __init bcm63xx_spi_register(void)
- spi_pdata.msg_ctl_width = SPI_6348_MSG_CTL_WIDTH;
- }
-
-- if (BCMCPU_IS_6358() || BCMCPU_IS_6362() || BCMCPU_IS_6368()) {
-+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6362() ||
-+ BCMCPU_IS_6368()) {
- spi_resources[0].end += BCM_6358_RSET_SPI_SIZE - 1;
- spi_pdata.fifo_size = SPI_6358_MSG_DATA_SIZE;
- spi_pdata.msg_type_shift = SPI_6358_MSG_TYPE_SHIFT;
---- a/arch/mips/bcm63xx/clk.c
-+++ b/arch/mips/bcm63xx/clk.c
-@@ -84,7 +84,7 @@ static void enetx_set(struct clk *clk, i
- else
- clk_disable_unlocked(&clk_enet_misc);
-
-- if (BCMCPU_IS_6358()) {
-+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358()) {
- u32 mask;
-
- if (clk->id == 0)
-@@ -110,9 +110,8 @@ static struct clk clk_enet1 = {
- */
- static void ephy_set(struct clk *clk, int enable)
- {
-- if (!BCMCPU_IS_6358())
-- return;
-- bcm_hwclock_set(CKCTL_6358_EPHY_EN, enable);
-+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358())
-+ bcm_hwclock_set(CKCTL_6358_EPHY_EN, enable);
- }
-
-
-@@ -155,9 +154,10 @@ static struct clk clk_enetsw = {
- */
- static void pcm_set(struct clk *clk, int enable)
- {
-- if (!BCMCPU_IS_6358())
-- return;
-- bcm_hwclock_set(CKCTL_6358_PCM_EN, enable);
-+ if (BCMCPU_IS_3368())
-+ bcm_hwclock_set(CKCTL_3368_PCM_EN, enable);
-+ if (BCMCPU_IS_6358())
-+ bcm_hwclock_set(CKCTL_6358_PCM_EN, enable);
- }
-
- static struct clk clk_pcm = {
-@@ -221,7 +221,7 @@ static void spi_set(struct clk *clk, int
- mask = CKCTL_6338_SPI_EN;
- else if (BCMCPU_IS_6348())
- mask = CKCTL_6348_SPI_EN;
-- else if (BCMCPU_IS_6358())
-+ else if (BCMCPU_IS_3368() || BCMCPU_IS_6358())
- mask = CKCTL_6358_SPI_EN;
- else if (BCMCPU_IS_6362())
- mask = CKCTL_6362_SPI_EN;
-@@ -370,7 +370,7 @@ struct clk *clk_get(struct device *dev,
- return &clk_xtm;
- if (!strcmp(id, "periph"))
- return &clk_periph;
-- if (BCMCPU_IS_6358() && !strcmp(id, "pcm"))
-+ if ((BCMCPU_IS_3368() || BCMCPU_IS_6358()) && !strcmp(id, "pcm"))
- return &clk_pcm;
- if ((BCMCPU_IS_6362() || BCMCPU_IS_6368()) && !strcmp(id, "ipsec"))
- return &clk_ipsec;
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -102,6 +102,7 @@ static int __init bcm63xx_detect_flash_t
- /* no way to auto detect so assume parallel */
- bcm63xx_attached_flash = BCM63XX_FLASH_TYPE_PARALLEL;
- break;
-+ case BCM3368_CPU_ID:
- case BCM6358_CPU_ID:
- val = bcm_gpio_readl(GPIO_STRAPBUS_REG);
- if (val & STRAPBUS_6358_BOOT_SEL_PARALLEL)
---- a/arch/mips/pci/pci-bcm63xx.c
-+++ b/arch/mips/pci/pci-bcm63xx.c
-@@ -266,7 +266,7 @@ static int __init bcm63xx_register_pci(v
- /* setup PCI to local bus access, used by PCI device to target
- * local RAM while bus mastering */
- bcm63xx_int_cfg_writel(0, PCI_BASE_ADDRESS_3);
-- if (BCMCPU_IS_6358() || BCMCPU_IS_6368())
-+ if (BCMCPU_IS_3368() || BCMCPU_IS_6358() || BCMCPU_IS_6368())
- val = MPI_SP0_REMAP_ENABLE_MASK;
- else
- val = 0;
-@@ -338,6 +338,7 @@ static int __init bcm63xx_pci_init(void)
- case BCM6328_CPU_ID:
- case BCM6362_CPU_ID:
- return bcm63xx_register_pcie();
-+ case BCM3368_CPU_ID:
- case BCM6348_CPU_ID:
- case BCM6358_CPU_ID:
- case BCM6368_CPU_ID:
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -37,6 +37,7 @@
- #include <pci_rt2x00_fixup.h>
-
- #include <uapi/linux/bcm963xx_tag.h>
-+#include <uapi/linux/bcm933xx_hcs.h>
-
- #define PFX "board_bcm963xx: "
-
-@@ -45,6 +46,7 @@
-
- #define CFE_OFFSET_64K 0x10000
- #define CFE_OFFSET_128K 0x20000
-+#define HCS_OFFSET_128K 0x20000
-
- static struct board_info board;
-
-@@ -782,8 +784,9 @@ void __init board_prom_init(void)
- unsigned int i;
- u8 *boot_addr, *cfe;
- char cfe_version[32];
-- char *board_name;
-+ char *board_name = NULL;
- u32 val;
-+ struct bcm_hcs *hcs;
-
- /* read base address of boot chip select (0)
- * 6328/6362 do not have MPI but boot from a fixed address
-@@ -812,9 +815,13 @@ void __init board_prom_init(void)
- if (strcmp(cfe_version, "unknown") != 0) {
- /* cfe present */
- boardid_fixup(boot_addr);
-+
-+ board_name = bcm63xx_nvram_get_name();
-+ } else if (BCMCPU_IS_3368()) {
-+ hcs = (struct bcm_hcs *)KSEG1ADDR(0x1fc00000 + HCS_OFFSET_128K);
-+ board_name = hcs->filename;
- }
-
-- board_name = bcm63xx_nvram_get_name();
- /* find board by name */
- for (i = 0; i < ARRAY_SIZE(bcm963xx_boards); i++) {
- if (strncmp(board_name, bcm963xx_boards[i]->name, 16))
---- /dev/null
-+++ b/include/uapi/linux/bcm933xx_hcs.h
-@@ -0,0 +1,18 @@
-+#ifndef __BCM_HCS_H
-+#define __BCM_HCS_H
-+
-+struct bcm_hcs {
-+ uint16_t magic;
-+ uint16_t control;
-+ uint16_t rev_maj;
-+ uint16_t rev_min;
-+ uint32_t build_date;
-+ uint32_t filelen;
-+ uint32_t ldaddress;
-+ char filename[64];
-+ uint16_t hcs;
-+ uint16_t her_znaet_chto;
-+ uint32_t crc;
-+};
-+
-+#endif /* __BCM_HCS */
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -522,6 +522,56 @@ static struct board_info __initdata boar
-
- .has_ohci0 = 1,
- };
-+
-+static struct board_info __initdata board_96348_D4PW = {
-+ .name = "D-4P-W",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+ .has_uart0 = 1,
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "D-4P-W:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "D-4P-W::status",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "D-4P-W:green:internet",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "D-4P-W:red:internet",
-+ .gpio = 5,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 7,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -696,6 +746,7 @@ static const struct board_info __initcon
- &board_DV201AMR,
- &board_96348gw_a,
- &board_rta1025w_16,
-+ &board_96348_D4PW,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -15,6 +15,8 @@
- #include <linux/gpio_keys.h>
- #include <linux/input.h>
- #include <linux/spi/spi.h>
-+#include <linux/spi/spi_gpio.h>
-+#include <linux/spi/74x164.h>
- #include <asm/addrspace.h>
- #include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
-@@ -48,6 +50,12 @@
- #define CFE_OFFSET_128K 0x20000
- #define HCS_OFFSET_128K 0x20000
-
-+#define NB4_PID_OFFSET 0xff80
-+#define NB4_74X164_GPIO_BASE 64
-+#define NB4_SPI_GPIO_MOSI 7
-+#define NB4_SPI_GPIO_CLK 6
-+#define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X))
-+
- static struct board_info board;
-
- /*
-@@ -721,6 +729,596 @@ static struct board_info __initdata boar
-
- .has_ohci0 = 1,
- };
-+
-+struct spi_gpio_platform_data nb4_spi_gpio_data = {
-+ .sck = NB4_SPI_GPIO_CLK,
-+ .mosi = NB4_SPI_GPIO_MOSI,
-+ .miso = SPI_GPIO_NO_MISO,
-+ .num_chipselect = 1,
-+};
-+
-+
-+static struct platform_device nb4_spi_gpio = {
-+ .name = "spi_gpio",
-+ .id = 1,
-+ .dev = {
-+ .platform_data = &nb4_spi_gpio_data,
-+ },
-+};
-+
-+static struct platform_device * __initdata nb4_devices[] = {
-+ &nb4_spi_gpio,
-+};
-+
-+const struct gen_74x164_chip_platform_data nb4_74x164_platform_data = {
-+ .base = NB4_74X164_GPIO_BASE
-+};
-+
-+static struct spi_board_info nb4_spi_devices[] = {
-+ {
-+ .modalias = "74x164",
-+ .max_speed_hz = 781000,
-+ .bus_num = 1,
-+ .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT,
-+ .mode = SPI_MODE_0,
-+ .platform_data = &nb4_74x164_platform_data
-+ }
-+};
-+
-+static struct board_info __initdata board_nb4_ser_r0 = {
-+ .name = "NB4-SER-r0",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+
-+ .has_ohci0 = 1,
-+ .has_pccard = 1,
-+ .has_ehci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "NB4-SER-r0:white:adsl",
-+ .gpio = NB4_74HC64_GPIO(4),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r0:white:traffic",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r0:white:tel",
-+ .gpio = NB4_74HC64_GPIO(3),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r0:white:tv",
-+ .gpio = NB4_74HC64_GPIO(2),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r0:white:wifi",
-+ .gpio = 15,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r0:white:alarm",
-+ .gpio = NB4_74HC64_GPIO(0),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r0:red:service",
-+ .gpio = 29,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r0:green:service",
-+ .gpio = 30,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r0:blue:service",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 34,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wps",
-+ .gpio = 37,
-+ .type = EV_KEY,
-+ .code = KEY_WPS_BUTTON,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "service",
-+ .gpio = 27,
-+ .type = EV_KEY,
-+ .code = BTN_0,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "clip",
-+ .gpio = 31,
-+ .type = EV_KEY,
-+ .code = BTN_1,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+ .devs = nb4_devices,
-+ .num_devs = ARRAY_SIZE(nb4_devices),
-+ .spis = nb4_spi_devices,
-+ .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_ser_r1 = {
-+ .name = "NB4-SER-r1",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+
-+ .has_ohci0 = 1,
-+ .has_pccard = 1,
-+ .has_ehci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "NB4-SER-r1:white:adsl",
-+ .gpio = NB4_74HC64_GPIO(4),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r1:white:traffic",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r1:white:tel",
-+ .gpio = NB4_74HC64_GPIO(3),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r1:white:tv",
-+ .gpio = NB4_74HC64_GPIO(2),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r1:white:wifi",
-+ .gpio = 15,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r1:white:alarm",
-+ .gpio = NB4_74HC64_GPIO(0),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r1:red:service",
-+ .gpio = 29,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r1:green:service",
-+ .gpio = 30,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r1:blue:service",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 34,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wps",
-+ .gpio = 37,
-+ .type = EV_KEY,
-+ .code = KEY_WPS_BUTTON,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "service",
-+ .gpio = 27,
-+ .type = EV_KEY,
-+ .code = BTN_0,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "clip",
-+ .gpio = 31,
-+ .type = EV_KEY,
-+ .code = BTN_1,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+ .devs = nb4_devices,
-+ .num_devs = ARRAY_SIZE(nb4_devices),
-+ .spis = nb4_spi_devices,
-+ .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_ser_r2 = {
-+ .name = "NB4-SER-r2",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+
-+ .has_ohci0 = 1,
-+ .has_pccard = 1,
-+ .has_ehci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "NB4-SER-r2:white:adsl",
-+ .gpio = NB4_74HC64_GPIO(4),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r2:white:traffic",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r2:white:tel",
-+ .gpio = NB4_74HC64_GPIO(3),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r2:white:tv",
-+ .gpio = NB4_74HC64_GPIO(2),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r2:white:wifi",
-+ .gpio = 15,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r2:white:alarm",
-+ .gpio = NB4_74HC64_GPIO(0),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r2:red:service",
-+ .gpio = 29,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r2:green:service",
-+ .gpio = 30,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-SER-r2:blue:service",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 34,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wps",
-+ .gpio = 37,
-+ .type = EV_KEY,
-+ .code = KEY_WPS_BUTTON,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "service",
-+ .gpio = 27,
-+ .type = EV_KEY,
-+ .code = BTN_0,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "clip",
-+ .gpio = 31,
-+ .type = EV_KEY,
-+ .code = BTN_1,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+ .devs = nb4_devices,
-+ .num_devs = ARRAY_SIZE(nb4_devices),
-+ .spis = nb4_spi_devices,
-+ .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_fxc_r1 = {
-+ .name = "NB4-FXC-r1",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+
-+ .has_ohci0 = 1,
-+ .has_pccard = 1,
-+ .has_ehci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "NB4-FXC-r1:white:adsl",
-+ .gpio = NB4_74HC64_GPIO(4),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-FXC-r1:white:traffic",
-+ .gpio = 2,
-+ },
-+ {
-+ .name = "NB4-FXC-r1:white:tel",
-+ .gpio = NB4_74HC64_GPIO(3),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-FXC-r1:white:tv",
-+ .gpio = NB4_74HC64_GPIO(2),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-FXC-r1:white:wifi",
-+ .gpio = 15,
-+ },
-+ {
-+ .name = "NB4-FXC-r1:white:alarm",
-+ .gpio = NB4_74HC64_GPIO(0),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-FXC-r1:red:service",
-+ .gpio = 29,
-+ },
-+ {
-+ .name = "NB4-FXC-r1:green:service",
-+ .gpio = 30,
-+ },
-+ {
-+ .name = "NB4-FXC-r1:blue:service",
-+ .gpio = 4,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 34,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wps",
-+ .gpio = 37,
-+ .type = EV_KEY,
-+ .code = KEY_WPS_BUTTON,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "service",
-+ .gpio = 27,
-+ .type = EV_KEY,
-+ .code = BTN_0,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "clip",
-+ .gpio = 31,
-+ .type = EV_KEY,
-+ .code = BTN_1,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+ .devs = nb4_devices,
-+ .num_devs = ARRAY_SIZE(nb4_devices),
-+ .spis = nb4_spi_devices,
-+ .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
-+
-+static struct board_info __initdata board_nb4_fxc_r2 = {
-+ .name = "NB4-FXC-r2",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+
-+ .has_ohci0 = 1,
-+ .has_pccard = 1,
-+ .has_ehci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "NB4-FXC-r2:white:adsl",
-+ .gpio = NB4_74HC64_GPIO(4),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-FXC-r2:white:traffic",
-+ .gpio = 2,
-+ },
-+ {
-+ .name = "NB4-FXC-r2:white:tel",
-+ .gpio = NB4_74HC64_GPIO(3),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-FXC-r2:white:tv",
-+ .gpio = NB4_74HC64_GPIO(2),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-FXC-r2:white:wifi",
-+ .gpio = 15,
-+ },
-+ {
-+ .name = "NB4-FXC-r2:white:alarm",
-+ .gpio = NB4_74HC64_GPIO(0),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "NB4-FXC-r2:red:service",
-+ .gpio = 29,
-+ },
-+ {
-+ .name = "NB4-FXC-r2:green:service",
-+ .gpio = 30,
-+ },
-+ {
-+ .name = "NB4-FXC-r2:blue:service",
-+ .gpio = 4,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 34,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wps",
-+ .gpio = 37,
-+ .type = EV_KEY,
-+ .code = KEY_WPS_BUTTON,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "service",
-+ .gpio = 27,
-+ .type = EV_KEY,
-+ .code = BTN_0,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "clip",
-+ .gpio = 31,
-+ .type = EV_KEY,
-+ .code = BTN_1,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+ .devs = nb4_devices,
-+ .num_devs = ARRAY_SIZE(nb4_devices),
-+ .spis = nb4_spi_devices,
-+ .num_spis = ARRAY_SIZE(nb4_spi_devices),
-+};
- #endif
-
- /*
-@@ -754,6 +1352,11 @@ static const struct board_info __initcon
- &board_96358vw2,
- &board_AGPFS0,
- &board_DWVS0,
-+ &board_nb4_ser_r0,
-+ &board_nb4_ser_r1,
-+ &board_nb4_ser_r2,
-+ &board_nb4_fxc_r1,
-+ &board_nb4_fxc_r2,
- #endif
- };
-
-@@ -808,6 +1411,16 @@ static void __init boardid_fixup(u8 *boo
- struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K);
- char *board_name = (char *)bcm63xx_nvram_get_name();
-
-+ if (BCMCPU_IS_6358() && (!strcmp(board_name, "96358VW"))) {
-+ u8 *p = boot_addr + NB4_PID_OFFSET;
-+
-+ /* Extract nb4 PID */
-+ if (!memcmp(p, "NB4-", 4)) {
-+ memcpy(board_name, p, sizeof("NB4-XXX-rX"));
-+ return;
-+ }
-+ }
-+
- /* check if bcm_tag is at 64k offset */
- if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) {
- /* else try 128k */
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -193,6 +193,40 @@ static struct board_info __initdata boar
- },
- },
- };
-+
-+static struct board_info __initdata board_96338w2_e7t = {
-+ .name = "96338W2_E7T",
-+ .expected_cpu_id = 0x6338,
-+
-+ .has_enet0 = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "96338W2_E7T:green:ppp",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "96338W2_E7T:green:ppp-fail",
-+ .gpio = 5,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "96338W2_E7T:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -1331,6 +1365,7 @@ static const struct board_info __initcon
- #ifdef CONFIG_BCM63XX_CPU_6338
- &board_96338gw,
- &board_96338w,
-+ &board_96338w2_e7t,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6345
- &board_96345gw2,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -720,6 +720,98 @@ static struct board_info __initdata boar
- },
- };
-
-+static struct board_info __initdata board_CPVA642 = {
-+ .name = "CPVA642",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "CPVA642:red:power",
-+ .gpio = 14,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CPVA642:green:power",
-+ .gpio = 11,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "CPVA642:red:wifi",
-+ .gpio = 6,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CPVA642:green:wifi",
-+ .gpio = 28,
-+ .active_low = 0,
-+ },
-+ {
-+ .name = "CPVA642:red:link",
-+ .gpio = 9,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CPVA642:green:link",
-+ .gpio = 10,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CPVA642:green:ether",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CPVA642:green:phone1",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CPVA642:green:phone2",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CPVA642:green:usb",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 36,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wps",
-+ .gpio = 37,
-+ .type = EV_KEY,
-+ .code = KEY_WPS_BUTTON,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
-+
- static struct board_info __initdata board_AGPFS0 = {
- .name = "AGPF-S0",
- .expected_cpu_id = 0x6358,
-@@ -1386,6 +1478,7 @@ static const struct board_info __initcon
- &board_96358vw,
- &board_96358vw2,
- &board_AGPFS0,
-+ &board_CPVA642,
- &board_DWVS0,
- &board_nb4_ser_r0,
- &board_nb4_ser_r1,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -856,6 +856,61 @@ static struct board_info __initdata boar
- .has_ohci0 = 1,
- };
-
-+/* D-Link DSL-274xB revison C2/C3 */
-+static struct board_info __initdata board_dsl_274xb_rev_c = {
-+ .name = "AW4139",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "dsl-274xb:green:power",
-+ .gpio = 5,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "dsl-274xb:red:power",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "dsl-274xb:green:adsl",
-+ .gpio = 9,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "dsl-274xb:green:internet",
-+ .gpio = 2,
-+ },
-+ {
-+ .name = "dsl-274xb:red:internet",
-+ .gpio = 10,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 34,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
- struct spi_gpio_platform_data nb4_spi_gpio_data = {
- .sck = NB4_SPI_GPIO_CLK,
- .mosi = NB4_SPI_GPIO_MOSI,
-@@ -1480,6 +1535,7 @@ static const struct board_info __initcon
- &board_AGPFS0,
- &board_CPVA642,
- &board_DWVS0,
-+ &board_dsl_274xb_rev_c,
- &board_nb4_ser_r0,
- &board_nb4_ser_r1,
- &board_nb4_ser_r2,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -614,6 +614,67 @@ static struct board_info __initdata boar
- },
- },
- };
-+
-+static struct board_info __initdata board_spw500v = {
-+ .name = "SPW500V",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+
-+ .has_dsp = 1,
-+ .dsp = {
-+ .gpio_rst = 6,
-+ .gpio_int = 34,
-+ .ext_irq = 2,
-+ .cs = 2,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "SPW500V:red:power",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "SPW500V:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "SPW500V:green:ppp",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ { .name = "SPW500V:green:pstn",
-+ .gpio = 28,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "SPW500V:green:voip",
-+ .gpio = 32,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 33,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -1527,6 +1588,7 @@ static const struct board_info __initcon
- &board_96348gw_a,
- &board_rta1025w_16,
- &board_96348_D4PW,
-+ &board_spw500v,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -481,6 +481,112 @@ static struct board_info __initdata boar
- },
- };
-
-+static struct board_info __initdata board_gw6200 = {
-+ .name = "GW6200",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+ .enet1 = {
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .has_ohci0 = 1,
-+
-+ .has_dsp = 1,
-+ .dsp = {
-+ .gpio_rst = 8, /* FIXME: What is real GPIO here? */
-+ .gpio_int = 34,
-+ .ext_irq = 2,
-+ .cs = 2,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "GW6200:green:line1",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "GW6200:green:line2",
-+ .gpio = 5,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "GW6200:green:line3",
-+ .gpio = 6,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "GW6200:green:tel",
-+ .gpio = 7,
-+ .active_low = 1,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 36,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
-+static struct board_info __initdata board_gw6000 = {
-+ .name = "GW6000",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+ .enet1 = {
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .has_ohci0 = 1,
-+
-+ .has_dsp = 1,
-+ .dsp = {
-+ .gpio_rst = 6,
-+ .gpio_int = 34,
-+ .ext_irq = 2,
-+ .cs = 2,
-+ },
-+
-+ /* GW6000 has no GPIO-controlled leds */
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 36,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
-+
-+
- static struct board_info __initdata board_FAST2404 = {
- .name = "F@ST2404",
- .expected_cpu_id = 0x6348,
-@@ -1581,6 +1687,8 @@ static const struct board_info __initcon
- #ifdef CONFIG_BCM63XX_CPU_6348
- &board_96348r,
- &board_96348gw,
-+ &board_gw6000,
-+ &board_gw6200,
- &board_96348gw_10,
- &board_96348gw_11,
- &board_FAST2404,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -781,6 +781,78 @@ static struct board_info __initdata boar
- },
- },
- };
-+
-+static struct board_info __initdata board_96348sv = {
-+ .name = "MAGIC",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+ .enet1 = {
-+ /* it has BP_ENET_EXTERNAL_PHY */
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .has_ohci0 = 1,
-+ .has_pccard = 1,
-+ .has_ehci0 = 1,
-+
-+ .has_dsp = 1,
-+ .dsp = {
-+ .gpio_rst = 25,
-+ .gpio_int = 34,
-+ .cs = 2,
-+ .ext_irq = 2,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "MAGIC:green:voip",
-+ .gpio = 22,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "MAGIC:green:adsl",
-+ .gpio = 5,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "MAGIC:green:wifi",
-+ .gpio = 28,
-+ },
-+ {
-+ .name = "MAGIC:green:usb",
-+ .gpio = 35,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "MAGIC:green:hpna",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "MAGIC:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "MAGIC:green:stop",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -1697,6 +1769,7 @@ static const struct board_info __initcon
- &board_rta1025w_16,
- &board_96348_D4PW,
- &board_spw500v,
-+ &board_96348sv,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1739,6 +1739,82 @@ static struct board_info __initdata boar
- .spis = nb4_spi_devices,
- .num_spis = ARRAY_SIZE(nb4_spi_devices),
- };
-+
-+static struct board_info __initdata board_HW553 = {
-+ .name = "HW553",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "HW553:red:lan",
-+ .gpio = 34,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW553:blue:lan",
-+ .gpio = 35,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW553:red:adsl",
-+ .gpio = 22,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW553:blue:adsl",
-+ .gpio = 23,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW553:red:power",
-+ .gpio = 5,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+
-+ {
-+ .name = "HW553:blue:power",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW553:red:wifi",
-+ .gpio = 25,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW553:red:internetkey",
-+ .gpio = 12,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW553:blue:internetkey",
-+ .gpio = 13,
-+ .active_low = 1,
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -1784,6 +1860,7 @@ static const struct board_info __initcon
- &board_nb4_ser_r2,
- &board_nb4_fxc_r1,
- &board_nb4_fxc_r2,
-+ &board_HW553,
- #endif
- };
-
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -227,6 +227,45 @@ static struct board_info __initdata boar
- },
- },
- };
-+
-+static struct board_info __initdata board_rta1320_16m = {
-+ .name = "RTA1320_16M",
-+ .expected_cpu_id = 0x6338,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "RTA1320_16M:green:adsl",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "RTA1320_16M:green:ppp",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "RTA1320_16M:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "RTA1320_16M:green:stop",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -1828,6 +1867,7 @@ static const struct board_info __initcon
- &board_96338gw,
- &board_96338w,
- &board_96338w2_e7t,
-+ &board_rta1320_16m,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6345
- &board_96345gw2,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1854,6 +1854,72 @@ static struct board_info __initdata boar
- },
- },
- };
-+
-+ /* T-Home Speedport W 303V Typ B */
-+static struct board_info __initdata board_spw303v = {
-+ .name = "96358-502V",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "spw303v:green:power+adsl",
-+ .gpio = 22,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "spw303v:red:power+adsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "spw303v:green:ppp",
-+ .gpio = 5,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "spw303v:green:ses",
-+ .gpio = 0,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "spw303v:green:voip",
-+ .gpio = 27,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "spw303v:green:pots",
-+ .gpio = 31,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 11,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "ses",
-+ .gpio = 37,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_WPS_BUTTON,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ }
-+};
- #endif
-
- /*
-@@ -1901,6 +1967,7 @@ static const struct board_info __initcon
- &board_nb4_fxc_r1,
- &board_nb4_fxc_r2,
- &board_HW553,
-+ &board_spw303v,
- #endif
- };
-
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -892,6 +892,65 @@ static struct board_info __initdata boar
- },
- },
- };
-+
-+static struct board_info __initdata board_V2500V_BB = {
-+ .name = "V2500V_BB",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "V2500V_BB:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "V2500V_BB:red:power",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "V2500V_BB:green:adsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ { .name = "V2500V_BB:green:ppp",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "V2500V_BB:green:wireless",
-+ .gpio = 6,
-+ .active_low = 1,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 31,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -1952,6 +2011,7 @@ static const struct board_info __initcon
- &board_96348_D4PW,
- &board_spw500v,
- &board_96348sv,
-+ &board_V2500V_BB,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
-@@ -2073,6 +2133,22 @@ void __init board_prom_init(void)
- val &= MPI_CSBASE_BASE_MASK;
- }
- boot_addr = (u8 *)KSEG1ADDR(val);
-+ printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
-+
-+ /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
-+ /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
-+ /* Loading firmware from the CFE Prompt always loads to Bank 0 */
-+ /* Do an early check of CFE and then select bank 0 */
-+
-+ if (boot_addr == (u8 *)0xbf800000) {
-+ u8 *tmp_boot_addr = (u8*)0xbfc00000;
-+
-+ bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET);
-+ if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
-+ printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
-+ boot_addr = tmp_boot_addr;
-+ }
-+ }
-
- /* dump cfe version */
- cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -19,6 +19,7 @@
- #include <linux/spi/spi.h>
- #include <linux/spi/flash.h>
-
-+#include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
- #include <bcm63xx_dev_flash.h>
- #include <bcm63xx_dev_hsspi.h>
-@@ -158,6 +159,13 @@ int __init bcm63xx_flash_register(int nu
- val = bcm_mpi_readl(MPI_CSBASE_REG(0));
- val &= MPI_CSBASE_BASE_MASK;
-
-+ /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
-+ /* Loading from CFE always uses Bank 0 */
-+ if (!strcmp(board_get_name(), "V2500V_BB")) {
-+ pr_info("V2500V: Start in Bank 0\n");
-+ val = val + 0x400000; // Select Bank 0 start address
-+ }
-+
- mtd_resources[0].start = val;
- mtd_resources[0].end = 0x1FFFFFFF;
-
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -452,6 +452,64 @@ static struct board_info __initdata boar
- },
- };
-
-+
-+/* BT Voyager 2110 */
-+static struct board_info __initdata board_V2110 = {
-+ .name = "V2110",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "V2110:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "V2110:red:power",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "V2110:green:adsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ { .name = "V2110:green:ppp",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "V2110:green:wireless",
-+ .gpio = 6,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 33,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
-+
- static struct board_info __initdata board_96348gw = {
- .name = "96348GW",
- .expected_cpu_id = 0x6348,
-@@ -2012,6 +2070,7 @@ static const struct board_info __initcon
- &board_spw500v,
- &board_96348sv,
- &board_V2500V_BB,
-+ &board_V2110,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/Kconfig
-+++ b/arch/mips/bcm63xx/boards/Kconfig
-@@ -8,4 +8,10 @@ config BOARD_BCM963XX
- select SSB
- help
-
-+config BOARD_LIVEBOX
-+ bool "Inventel Livebox(es) boards"
-+ select SSB
-+ help
-+ Inventel Livebox boards using the RedBoot bootloader.
-+
- endchoice
---- a/arch/mips/bcm63xx/boards/Makefile
-+++ b/arch/mips/bcm63xx/boards/Makefile
-@@ -1 +1,2 @@
- obj-$(CONFIG_BOARD_BCM963XX) += board_bcm963xx.o
-+obj-$(CONFIG_BOARD_LIVEBOX) += board_livebox.o
---- /dev/null
-+++ b/arch/mips/bcm63xx/boards/board_livebox.c
-@@ -0,0 +1,369 @@
-+/*
-+ * This file is subject to the terms and conditions of the GNU General Public
-+ * License. See the file "COPYING" in the main directory of this archive
-+ * for more details.
-+ *
-+ * Copyright (C) 2008 Florian Fainelli <florian@openwrt.org>
-+ */
-+
-+#include <linux/init.h>
-+#include <linux/kernel.h>
-+#include <linux/string.h>
-+#include <linux/platform_device.h>
-+#include <linux/mtd/mtd.h>
-+#include <linux/mtd/partitions.h>
-+#include <linux/mtd/physmap.h>
-+#include <linux/ssb/ssb.h>
-+#include <linux/gpio_keys.h>
-+#include <linux/input.h>
-+#include <linux/spi/spi.h>
-+#include <asm/addrspace.h>
-+#include <bcm63xx_board.h>
-+#include <bcm63xx_cpu.h>
-+#include <bcm63xx_dev_uart.h>
-+#include <bcm63xx_regs.h>
-+#include <bcm63xx_io.h>
-+#include <bcm63xx_dev_pci.h>
-+#include <bcm63xx_dev_enet.h>
-+#include <bcm63xx_dev_dsp.h>
-+#include <bcm63xx_dev_pcmcia.h>
-+#include <bcm63xx_dev_usb_ohci.h>
-+#include <bcm63xx_dev_usb_ehci.h>
-+#include <bcm63xx_dev_spi.h>
-+#include <board_bcm963xx.h>
-+
-+#define PFX "board_livebox: "
-+
-+#define LIVEBOX_KEYS_POLL_INTERVAL 20
-+#define LIVEBOX_KEYS_DEBOUNCE_INTERVAL (LIVEBOX_KEYS_POLL_INTERVAL * 3)
-+
-+static unsigned int mac_addr_used = 0;
-+static struct board_info board;
-+
-+/*
-+ * known 6348 boards
-+ */
-+#ifdef CONFIG_BCM63XX_CPU_6348
-+static struct board_info __initdata board_livebox_blue5g = {
-+ .name = "Livebox-blue-5g",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 31,
-+ },
-+
-+ .has_ohci0 = 1,
-+ .has_pccard = 1,
-+
-+ .has_dsp = 0, /*TODO some Liveboxes have dsp*/
-+ .dsp = {
-+ .gpio_rst = 6, /*FIXME eth1 shares gpio6 with dsp?*/
-+ .gpio_int = 35,
-+ .cs = 2,
-+ .ext_irq = 2,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "Livebox-blue-5g::adsl-fail",
-+ .gpio = 0,
-+ .active_low = 0,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "Livebox-blue-5g::adsl",
-+ .gpio = 1,
-+ },
-+ {
-+ .name = "Livebox-blue-5g::traffic",
-+ .gpio = 2,
-+ },
-+ {
-+ .name = "Livebox-blue-5g::phone",
-+ .gpio = 3,
-+ },
-+ {
-+ .name = "Livebox-blue-5g::wifi",
-+ .gpio = 4,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "BTN_1",
-+ .gpio = 36,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = BTN_1,
-+ .debounce_interval = LIVEBOX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "BTN_2",
-+ .gpio = 7,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = BTN_2,
-+ .debounce_interval = LIVEBOX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+
-+ },
-+};
-+#endif
-+
-+/*
-+ * all boards
-+ */
-+static const struct board_info __initdata *bcm963xx_boards[] = {
-+#ifdef CONFIG_BCM63XX_CPU_6348
-+ &board_livebox_blue5g
-+#endif
-+};
-+/*
-+ * return board name for /proc/cpuinfo
-+ */
-+const char *board_get_name(void)
-+{
-+ return board.name;
-+}
-+
-+/*
-+ * register & return a new board mac address
-+ */
-+static int board_get_mac_address(u8 *mac)
-+{
-+ u8 *p;
-+ int count;
-+
-+ memcpy(mac, (u8 *)0xBEBFF377, ETH_ALEN);
-+
-+ p = mac + ETH_ALEN - 1;
-+ count = mac_addr_used;
-+
-+ while (count--) {
-+ do {
-+ (*p)++;
-+ if (*p != 0)
-+ break;
-+ p--;
-+ } while (p != mac);
-+ }
-+
-+ if (p == mac) {
-+ printk(KERN_ERR PFX "unable to fetch mac address\n");
-+ return -ENODEV;
-+ }
-+ mac_addr_used++;
-+
-+ return 0;
-+}
-+
-+/*
-+ * early init callback
-+ */
-+#define LIVEBOX_GPIO_DETECT_MASK 0x000000ff
-+#define LIVEBOX_BOOT_ADDR 0x1e400000
-+
-+#define LIVEBOX_HW_BLUE5G_9 0x90
-+
-+void __init board_prom_init(void)
-+{
-+ u32 val;
-+ u8 hw_version;
-+
-+ /* Get hardware version */
-+ val = bcm_gpio_readl(GPIO_CTL_LO_REG);
-+ val &= ~LIVEBOX_GPIO_DETECT_MASK;
-+ bcm_gpio_writel(val, GPIO_CTL_LO_REG);
-+
-+ hw_version = bcm_gpio_readl(GPIO_DATA_LO_REG) & LIVEBOX_GPIO_DETECT_MASK;
-+ switch (hw_version) {
-+ case LIVEBOX_HW_BLUE5G_9:
-+ printk(KERN_INFO PFX "Livebox BLUE5G.9\n");
-+ memcpy(&board, bcm963xx_boards[0], sizeof(board));
-+ break;
-+ default:
-+ printk(KERN_INFO PFX "Unknown livebox version: %02x\n", hw_version);
-+ break;
-+ }
-+
-+ /* use default livebox configuration */
-+ memcpy(&board, bcm963xx_boards[0], sizeof(board));
-+
-+ /* setup pin multiplexing depending on board enabled device,
-+ * this has to be done this early since PCI init is done
-+ * inside arch_initcall */
-+ val = 0;
-+
-+#ifdef CONFIG_PCI
-+ if (board.has_pci) {
-+ bcm63xx_pci_enabled = 1;
-+ if (BCMCPU_IS_6348())
-+ val |= GPIO_MODE_6348_G2_PCI;
-+ }
-+#endif
-+ if (board.has_pccard) {
-+ if (BCMCPU_IS_6348())
-+ val |= GPIO_MODE_6348_G1_MII_PCCARD;
-+ }
-+
-+ if (board.has_enet0 && !board.enet0.use_internal_phy) {
-+ if (BCMCPU_IS_6348())
-+ val |= GPIO_MODE_6348_G3_EXT_MII |
-+ GPIO_MODE_6348_G0_EXT_MII;
-+ }
-+
-+ if (board.has_enet1 && !board.enet1.use_internal_phy) {
-+ if (BCMCPU_IS_6348())
-+ val |= GPIO_MODE_6348_G3_EXT_MII |
-+ GPIO_MODE_6348_G0_EXT_MII;
-+ printk(KERN_INFO PFX "resetting gpio6 for eth1...\n");
-+ gpio_request(6, "dsp_eth_rst");
-+ gpio_direction_output(6, 0);
-+ gpio_set_value(6, 1);
-+ }
-+
-+ bcm_gpio_writel(val, GPIO_MODE_REG);
-+}
-+
-+/*
-+ * second stage init callback, good time to panic if we couldn't
-+ * identify on which board we're running since early printk is working
-+ */
-+void __init board_setup(void)
-+{
-+ if (!board.name[0])
-+ panic("unable to detect bcm963xx board");
-+ printk(KERN_INFO PFX "board name: %s\n", board.name);
-+
-+ /* make sure we're running on expected cpu */
-+ if (bcm63xx_get_cpu_id() != board.expected_cpu_id)
-+ panic("unexpected CPU for bcm963xx board");
-+}
-+
-+static struct physmap_flash_data flash_data = {
-+ .width = 2,
-+};
-+
-+static struct resource mtd_resources[] = {
-+ {
-+ .start = 0, /* filled at runtime */
-+ .end = 0, /* filled at runtime */
-+ .flags = IORESOURCE_MEM,
-+ }
-+};
-+
-+static struct platform_device mtd_dev = {
-+ .name = "physmap-flash",
-+ .resource = mtd_resources,
-+ .num_resources = ARRAY_SIZE(mtd_resources),
-+ .dev = {
-+ .platform_data = &flash_data,
-+ },
-+};
-+
-+static struct gpio_led_platform_data bcm63xx_led_data;
-+
-+static struct platform_device bcm63xx_gpio_leds = {
-+ .name = "leds-gpio",
-+ .id = 0,
-+ .dev.platform_data = &bcm63xx_led_data,
-+};
-+
-+static struct gpio_keys_platform_data bcm63xx_gpio_keys_data = {
-+ .poll_interval = LIVEBOX_KEYS_POLL_INTERVAL,
-+};
-+
-+static struct platform_device bcm63xx_gpio_keys_device = {
-+ .name = "gpio-keys-polled",
-+ .id = 0,
-+ .dev.platform_data = &bcm63xx_gpio_keys_data,
-+};
-+
-+/*
-+ * third stage init callback, register all board devices.
-+ */
-+int __init board_register_devices(void)
-+{
-+ u32 val;
-+ int led_count = 0;
-+ int button_count = 0;
-+
-+ if (board.has_uart0)
-+ bcm63xx_uart_register(0);
-+
-+ if (board.has_uart1)
-+ bcm63xx_uart_register(1);
-+
-+ if (board.has_pccard)
-+ bcm63xx_pcmcia_register();
-+
-+ if (board.has_enet0 &&
-+ !board_get_mac_address(board.enet0.mac_addr))
-+ bcm63xx_enet_register(0, &board.enet0);
-+
-+ if (board.has_enet1 &&
-+ !board_get_mac_address(board.enet1.mac_addr))
-+ bcm63xx_enet_register(1, &board.enet1);
-+
-+ if (board.has_ehci0)
-+ bcm63xx_ehci_register();
-+
-+ if (board.has_ohci0)
-+ bcm63xx_ohci_register();
-+
-+ if (board.has_dsp)
-+ bcm63xx_dsp_register(&board.dsp);
-+
-+ bcm63xx_spi_register();
-+
-+ if (board.num_devs)
-+ platform_add_devices(board.devs, board.num_devs);
-+
-+ if (board.num_spis)
-+ spi_register_board_info(board.spis, board.num_spis);
-+
-+
-+ /* read base address of boot chip select (0) */
-+ val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-+ val &= MPI_CSBASE_BASE_MASK;
-+ if (val != LIVEBOX_BOOT_ADDR)
-+ printk(KERN_NOTICE PFX "flash address is: 0x%08x, forcing to: 0x%08x\n",
-+ val, LIVEBOX_BOOT_ADDR);
-+ mtd_resources[0].start = LIVEBOX_BOOT_ADDR;
-+ mtd_resources[0].end = 0x1ebfffff;
-+
-+ platform_device_register(&mtd_dev);
-+
-+ /* count number of LEDs defined by this device */
-+ while (led_count < ARRAY_SIZE(board.leds) && board.leds[led_count].name)
-+ led_count++;
-+
-+ bcm63xx_led_data.num_leds = led_count;
-+ bcm63xx_led_data.leds = board.leds;
-+
-+ platform_device_register(&bcm63xx_gpio_leds);
-+
-+ /* count number of BUTTONs defined by this device */
-+ while (button_count < ARRAY_SIZE(board.buttons) && board.buttons[button_count].desc)
-+ button_count++;
-+
-+ if (button_count) {
-+ bcm63xx_gpio_keys_data.nbuttons = button_count;
-+ bcm63xx_gpio_keys_data.buttons = board.buttons;
-+
-+ platform_device_register(&bcm63xx_gpio_keys_device);
-+ }
-+
-+ return 0;
-+}
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -510,6 +510,51 @@ static struct board_info __initdata boar
- };
-
-
-+static struct board_info __initdata board_ct536_ct5621 = {
-+ .name = "CT536_CT5621",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 0,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .has_ohci0 = 1,
-+ .has_pccard = 1,
-+ .has_ehci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "CT536_CT5621:green:adsl-fail",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CT536_CT5621:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 33,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
- static struct board_info __initdata board_96348gw = {
- .name = "96348GW",
- .expected_cpu_id = 0x6348,
-@@ -2071,6 +2116,7 @@ static const struct board_info __initcon
- &board_96348sv,
- &board_V2500V_BB,
- &board_V2110,
-+ &board_ct536_ct5621,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1279,6 +1279,8 @@ static struct board_info __initdata boar
- .name = "DWV-S0",
- .expected_cpu_id = 0x6358,
-
-+ .has_uart0 = 1,
-+
- .has_enet0 = 1,
- .has_enet1 = 1,
- .has_pci = 1,
-@@ -1294,6 +1296,7 @@ static struct board_info __initdata boar
- },
-
- .has_ohci0 = 1,
-+ .has_ehci0 = 1,
- };
-
- /* D-Link DSL-274xB revison C2/C3 */
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -555,6 +555,69 @@ static struct board_info __initdata boar
- },
- };
-
-+static struct board_info __initdata board_96348A_122 = {
-+ .name = "96348A-122",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .has_ohci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "96348A-122:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "96348A-122:red:alarm",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "96348A-122:green:wps",
-+ .gpio = 6,
-+ .active_low = 1,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 33,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wlan",
-+ .gpio = 34,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_WLAN,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wps",
-+ .gpio = 35,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_WPS_BUTTON,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
- static struct board_info __initdata board_96348gw = {
- .name = "96348GW",
- .expected_cpu_id = 0x6348,
-@@ -2120,6 +2183,7 @@ static const struct board_info __initcon
- &board_V2500V_BB,
- &board_V2110,
- &board_ct536_ct5621,
-+ &board_96348A_122,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -820,6 +820,7 @@ static struct board_info __initdata boar
- .name = "RTA1025W_16",
- .expected_cpu_id = 0x6348,
-
-+ .has_uart0 = 1,
- .has_enet0 = 1,
- .has_enet1 = 1,
- .has_pci = 1,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1118,6 +1118,46 @@ static struct board_info __initdata boar
- },
- },
- };
-+
-+static struct board_info __initdata board_CPVA502plus = {
-+ .name = "CPVA502+",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "CPVA502+:green:phone",
-+ .gpio = 0,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CPVA502+:green:link",
-+ .gpio = 5,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CPVA502+:green:feth1", /* FIXME:does gpio4 enable eth1 phy? */
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ },
-+};
-+
- #endif
-
- /*
-@@ -2185,6 +2225,7 @@ static const struct board_info __initcon
- &board_V2110,
- &board_ct536_ct5621,
- &board_96348A_122,
-+ &board_CPVA502plus,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
+++ /dev/null
-From eeacc2529942051504bc957726aa178671344421 Mon Sep 17 00:00:00 2001
-From: Maxime Bizon <mbizon@freebox.fr>
-Date: Wed, 20 Jan 2010 16:21:30 +0100
-Subject: [PATCH 32/63] bcm63xx: add support for 96368MVWG board.
-
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 95 ++++++++++++++++++++
- .../mips/include/asm/mach-bcm63xx/board_bcm963xx.h | 2 +
- 2 files changed, 97 insertions(+), 0 deletions(-)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -2192,6 +2192,78 @@ static struct board_info __initdata boar
- #endif
-
- /*
-+ * known 6368 boards
-+ */
-+#ifdef CONFIG_BCM63XX_CPU_6368
-+static struct board_info __initdata board_96368mvwg = {
-+ .name = "96368MVWG",
-+ .expected_cpu_id = 0x6368,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+ .has_enetsw = 1,
-+
-+ .enetsw = {
-+ .used_ports = {
-+ [1] = {
-+ .used = 1,
-+ .phy_id = 2,
-+ .name = "port1",
-+ },
-+
-+ [2] = {
-+ .used = 1,
-+ .phy_id = 3,
-+ .name = "port2",
-+ },
-+
-+ [4] = {
-+ .used = 1,
-+ .phy_id = 0x12,
-+ .name = "port0",
-+ },
-+
-+ [5] = {
-+ .used = 1,
-+ .phy_id = 0x11,
-+ .name = "port3",
-+ },
-+ },
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "96368MVWG:green:adsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "96368MVWG:green:ppp",
-+ .gpio = 5,
-+ },
-+ {
-+ .name = "96368MVWG:green:power",
-+ .gpio = 22,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "96368MVWG:green:wps",
-+ .gpio = 23,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "96368MVWG:green:ppp-fail",
-+ .gpio = 31,
-+ },
-+ },
-+
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+};
-+#endif
-+
-+/*
- * all boards
- */
- static const struct board_info __initconst *bcm963xx_boards[] = {
-@@ -2243,6 +2315,10 @@ static const struct board_info __initcon
- &board_HW553,
- &board_spw303v,
- #endif
-+
-+#ifdef CONFIG_BCM63XX_CPU_6368
-+ &board_96368mvwg,
-+#endif
- };
-
- /*
-@@ -2416,12 +2492,25 @@ void __init board_prom_init(void)
- bcm63xx_pci_enabled = 1;
- if (BCMCPU_IS_6348())
- val |= GPIO_MODE_6348_G2_PCI;
-+
-+ if (BCMCPU_IS_6368())
-+ val |= GPIO_MODE_6368_PCI_REQ1 |
-+ GPIO_MODE_6368_PCI_GNT1 |
-+ GPIO_MODE_6368_PCI_INTB |
-+ GPIO_MODE_6368_PCI_REQ0 |
-+ GPIO_MODE_6368_PCI_GNT0;
- }
- #endif
-
- if (board.has_pccard) {
- if (BCMCPU_IS_6348())
- val |= GPIO_MODE_6348_G1_MII_PCCARD;
-+
-+ if (BCMCPU_IS_6368())
-+ val |= GPIO_MODE_6368_PCMCIA_CD1 |
-+ GPIO_MODE_6368_PCMCIA_CD2 |
-+ GPIO_MODE_6368_PCMCIA_VS1 |
-+ GPIO_MODE_6368_PCMCIA_VS2;
- }
-
- if (board.has_enet0 && !board.enet0.use_internal_phy) {
+++ /dev/null
-From f457fc2eb9bb915b5a4d251c7c68d4694cf07b01 Mon Sep 17 00:00:00 2001
-From: Maxime Bizon <mbizon@freebox.fr>
-Date: Fri, 4 Nov 2011 12:33:48 +0100
-Subject: [PATCH 33/63] bcm63xx: add support for 96368MVNgr board.
-
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 67 +++++++++++++++++++++++++++++
- 1 files changed, 67 insertions(+), 0 deletions(-)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -2261,6 +2261,72 @@ static struct board_info __initdata boar
- .has_ohci0 = 1,
- .has_ehci0 = 1,
- };
-+
-+static struct board_info __initdata board_96368mvngr = {
-+ .name = "96368MVNgr",
-+ .expected_cpu_id = 0x6368,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+ .has_enetsw = 1,
-+
-+ .enetsw = {
-+ .used_ports = {
-+ [0] = {
-+ .used = 1,
-+ .phy_id = 1,
-+ .name = "port1",
-+ },
-+
-+ [1] = {
-+ .used = 1,
-+ .phy_id = 2,
-+ .name = "port2",
-+ },
-+
-+ [2] = {
-+ .used = 1,
-+ .phy_id = 3,
-+ .name = "port3",
-+ },
-+
-+ [3] = {
-+ .used = 1,
-+ .phy_id = 4,
-+ .name = "port4",
-+ },
-+ },
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "96368MVNgr:green:adsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "96368MVNgr:green:inet",
-+ .gpio = 5,
-+ },
-+ {
-+ .name = "96368MVNgr:green:power",
-+ .gpio = 22,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "96368MVNgr:green:wps",
-+ .gpio = 23,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "96368MVNgr:green:inet-fail",
-+ .gpio = 3,
-+ },
-+ },
-+
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+};
- #endif
-
- /*
-@@ -2318,6 +2384,7 @@ static const struct board_info __initcon
-
- #ifdef CONFIG_BCM63XX_CPU_6368
- &board_96368mvwg,
-+ &board_96368mvngr,
- #endif
- };
-
+++ /dev/null
-From c93c2bbf0cc96da5a47d77f01daf6c983cfe4216 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Tue, 29 May 2012 10:52:25 +0200
-Subject: [PATCH] MIPS: BCM63XX: add 96328avng reference board
-
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 77 +++++++++++++++++++++++++++++
- 1 files changed, 77 insertions(+), 0 deletions(-)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -75,13 +75,45 @@ static struct board_info __initdata boar
- .port_no = 0,
- },
-
-+ .has_enetsw = 1,
-+
-+ .enetsw = {
-+ .used_ports = {
-+ [0] = {
-+ .used = 1,
-+ .phy_id = 1,
-+ .name = "Port 1",
-+ },
-+ [1] = {
-+ .used = 1,
-+ .phy_id = 2,
-+ .name = "Port 2",
-+ },
-+ [2] = {
-+ .used = 1,
-+ .phy_id = 3,
-+ .name = "Port 3",
-+ },
-+ [3] = {
-+ .used = 1,
-+ .phy_id = 4,
-+ .name = "Port 4",
-+ },
-+ },
-+ },
-+
- .leds = {
- {
-- .name = "96328avng::ppp-fail",
-+ .name = "96328avng::internet-fail",
- .gpio = 2,
- .active_low = 1,
- },
- {
-+ .name = "96328avng::dsl",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ {
- .name = "96328avng::power",
- .gpio = 4,
- .active_low = 1,
-@@ -98,7 +130,7 @@ static struct board_info __initdata boar
- .active_low = 1,
- },
- {
-- .name = "96328avng::ppp",
-+ .name = "96328avng::internet",
- .gpio = 11,
- .active_low = 1,
- },
+++ /dev/null
-From f0649f7b7c672cf452a1796a1422bf615e1973f8 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Tue, 29 May 2012 11:01:12 +0200
-Subject: [PATCH] MIPS: BCM63XX: add 963281TAN reference board
-
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 71 +++++++++++++++++++++++++++++
- 1 files changed, 71 insertions(+), 0 deletions(-)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -136,6 +136,76 @@ static struct board_info __initdata boar
- },
- },
- };
-+
-+static struct board_info __initdata board_963281TAN = {
-+ .name = "963281TAN",
-+ .expected_cpu_id = 0x6328,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+
-+ .has_enetsw = 1,
-+
-+ .enetsw = {
-+ .used_ports = {
-+ [0] = {
-+ .used = 1,
-+ .phy_id = 1,
-+ .name = "Port 1",
-+ },
-+ [1] = {
-+ .used = 1,
-+ .phy_id = 2,
-+ .name = "Port 2",
-+ },
-+ [2] = {
-+ .used = 1,
-+ .phy_id = 3,
-+ .name = "Port 3",
-+ },
-+ [3] = {
-+ .used = 1,
-+ .phy_id = 4,
-+ .name = "Port 4",
-+ },
-+ },
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "963281TAN::internet",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281TAN::power",
-+ .gpio = 4,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "963281TAN::internet-fail",
-+ .gpio = 7,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281TAN::power-fail",
-+ .gpio = 8,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281TAN::wps",
-+ .gpio = 9,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281TAN::dsl",
-+ .gpio = 11,
-+ .active_low = 1,
-+ },
-+
-+ },
-+};
- #endif
-
- /*
-@@ -2367,6 +2437,7 @@ static struct board_info __initdata boar
- static const struct board_info __initconst *bcm963xx_boards[] = {
- #ifdef CONFIG_BCM63XX_CPU_6328
- &board_96328avng,
-+ &board_963281TAN,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6338
- &board_96338gw,
+++ /dev/null
-From 66808f706b3dcd83a9f5157997ff478a880a2906 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jonas.gorski@gmail.com>
-Date: Mon, 30 Apr 2012 09:10:51 +0200
-Subject: [PATCH 70/79] MIPS: BCM63XX: Add board definition for D-Link
- DSL-274xB rev F1
-
----
- arch/mips/bcm63xx/boards/board_bcm963xx.c | 104 +++++++++++++++++++++++++++++
- 1 files changed, 104 insertions(+), 0 deletions(-)
-
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -206,6 +206,111 @@ static struct board_info __initdata boar
-
- },
- };
-+
-+static struct board_info __initdata board_dsl_274xb_f1 = {
-+ .name = "AW4339U",
-+ .expected_cpu_id = 0x6328,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+
-+ .has_caldata = 1,
-+ .caldata = {
-+ {
-+ .vendor = PCI_VENDOR_ID_ATHEROS,
-+ .caldata_offset = 0x7d1000,
-+ .slot = 0,
-+ .led_pin = -1,
-+ },
-+ },
-+
-+ .has_enetsw = 1,
-+
-+ .enetsw = {
-+ .used_ports = {
-+ [0] = {
-+ .used = 1,
-+ .phy_id = 1,
-+ .name = "Port 4",
-+ },
-+ [1] = {
-+ .used = 1,
-+ .phy_id = 2,
-+ .name = "Port 3",
-+ },
-+ [2] = {
-+ .used = 1,
-+ .phy_id = 3,
-+ .name = "Port 2",
-+ },
-+ [3] = {
-+ .used = 1,
-+ .phy_id = 4,
-+ .name = "Port 1",
-+ },
-+ },
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "dsl-274xb:red:internet",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "dsl-274xb:green:dsl",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "dsl-274xb:green:power",
-+ .gpio = 4,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "dsl-274xb:red:power",
-+ .gpio = 8,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "dsl-274xb:blue:wps",
-+ .gpio = 9,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "dsl-274xb:green:internet",
-+ .gpio = 11,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "wifi",
-+ .gpio = 10,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = BTN_0,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "reset",
-+ .gpio = 23,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wps",
-+ .gpio = 24,
-+ .active_low = 1,
-+ .code = KEY_WPS_BUTTON,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -2438,6 +2543,7 @@ static const struct board_info __initcon
- #ifdef CONFIG_BCM63XX_CPU_6328
- &board_96328avng,
- &board_963281TAN,
-+ &board_dsl_274xb_f1,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6338
- &board_96338gw,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1365,6 +1365,59 @@ static struct board_info __initdata boar
- },
- };
-
-+/* NetGear DG834G v4 */
-+static struct board_info __initdata board_96348W3 = {
-+ .name = "96348W3",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .has_ohci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "96348W3:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "96348W3:red:power",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "96348W3::adsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "96348W3::internet",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 6,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
- #endif
-
- /*
-@@ -2573,6 +2626,7 @@ static const struct board_info __initcon
- &board_ct536_ct5621,
- &board_96348A_122,
- &board_CPVA502plus,
-+ &board_96348W3,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6358
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -56,6 +56,13 @@
- #define NB4_SPI_GPIO_CLK 6
- #define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X))
-
-+#define CT6373_PID_OFFSET 0xff80
-+#define CT6373_74X164_GPIO_BASE 64
-+#define CT6373_SPI_GPIO_MOSI 7
-+#define CT6373_SPI_GPIO_CLK 6
-+#define CT6373_74HC64_GPIO(X) (CT6373_74X164_GPIO_BASE + (X))
-+
-+
- static struct board_info board;
-
- /*
-@@ -2308,6 +2315,113 @@ static struct board_info __initdata boar
- .num_spis = ARRAY_SIZE(nb4_spi_devices),
- };
-
-+
-+struct spi_gpio_platform_data ct6373_spi_gpio_data = {
-+ .sck = CT6373_SPI_GPIO_CLK,
-+ .mosi = CT6373_SPI_GPIO_MOSI,
-+ .miso = SPI_GPIO_NO_MISO,
-+ .num_chipselect = 1,
-+};
-+
-+static struct platform_device ct6373_spi_gpio = {
-+ .name = "spi_gpio",
-+ .id = 1,
-+ .dev = {
-+ .platform_data = &ct6373_spi_gpio_data,
-+ },
-+};
-+
-+static struct platform_device * __initdata ct6373_devices[] = {
-+ &ct6373_spi_gpio,
-+};
-+
-+const struct gen_74x164_chip_platform_data ct6373_74x164_platform_data = {
-+ .base = CT6373_74X164_GPIO_BASE
-+};
-+
-+static struct spi_board_info ct6373_spi_devices[] = {
-+ {
-+ .modalias = "74x164",
-+ .max_speed_hz = 781000,
-+ .bus_num = 1,
-+ .controller_data = (void *) SPI_GPIO_NO_CHIPSELECT,
-+ .mode = SPI_MODE_0,
-+ .platform_data = &ct6373_74x164_platform_data
-+ }
-+};
-+
-+static struct board_info __initdata board_ct6373_1 = {
-+ .name = "CT6373-1",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+
-+ .has_enet1 = 1,
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "CT6373-1:green:power",
-+ .gpio = 0,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "CT6373-1:green:usb",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CT6373-1:green:wlan",
-+ .gpio = 9,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CT6373-1:green:adsl",
-+ .gpio = CT6373_74HC64_GPIO(0),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CT6373-1:green:line",
-+ .gpio = CT6373_74HC64_GPIO(1),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CT6373-1:green:fxs1",
-+ .gpio = CT6373_74HC64_GPIO(2),
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "CT6373-1:green:fxs2",
-+ .gpio = CT6373_74HC64_GPIO(3),
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 35,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+
-+ .devs = ct6373_devices,
-+ .num_devs = ARRAY_SIZE(ct6373_devices),
-+ .spis = ct6373_spi_devices,
-+ .num_spis = ARRAY_SIZE(ct6373_spi_devices),
-+};
-+
- static struct board_info __initdata board_HW553 = {
- .name = "HW553",
- .expected_cpu_id = 0x6358,
-@@ -2641,6 +2755,7 @@ static const struct board_info __initcon
- &board_nb4_ser_r2,
- &board_nb4_fxc_r1,
- &board_nb4_fxc_r2,
-+ &board_ct6373_1,
- &board_HW553,
- &board_spw303v,
- #endif
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -2563,6 +2563,73 @@ static struct board_info __initdata boar
- },
- }
- };
-+
-+/* D-Link DVA-G3810BN/TL */
-+static struct board_info __initdata board_DVAG3810BN = {
-+ .name = "DVAG3810BN",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_enet0 = 1,
-+ .has_enet1 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 0,
-+ .use_internal_phy = 1,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+
-+ .has_ohci0 = 1,
-+ .has_pccard = 1,
-+ .has_ehci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "DVAG3810BN::voip",
-+ .gpio = 1,
-+ },
-+ {
-+ .name = "DVAG3810BN::dsl",
-+ .gpio = 22,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DVAG3810BN::internet",
-+ .gpio = 23,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DVAG3810BN::power",
-+ .gpio = 4,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "DVAG3810BN::stop",
-+ .gpio = 5,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 34,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -2758,6 +2825,7 @@ static const struct board_info __initcon
- &board_ct6373_1,
- &board_HW553,
- &board_spw303v,
-+ &board_DVAG3810BN,
- #endif
-
- #ifdef CONFIG_BCM63XX_CPU_6368
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -17,6 +17,7 @@
- #include <linux/spi/spi.h>
- #include <linux/spi/spi_gpio.h>
- #include <linux/spi/74x164.h>
-+#include <linux/rtl8367.h>
- #include <asm/addrspace.h>
- #include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
-@@ -55,6 +56,8 @@
- #define NB4_SPI_GPIO_MOSI 7
- #define NB4_SPI_GPIO_CLK 6
- #define NB4_74HC64_GPIO(X) (NB4_74X164_GPIO_BASE + (X))
-+#define NB6_GPIO_RTL8367_SDA 18
-+#define NB6_GPIO_RTL8367_SCK 20
-
- #define CT6373_PID_OFFSET 0xff80
- #define CT6373_74X164_GPIO_BASE 64
-@@ -2632,6 +2635,103 @@ static struct board_info __initdata boar
- };
- #endif
-
-+#ifdef CONFIG_BCM63XX_CPU_6362
-+static struct rtl8367_extif_config nb6_rtl8367_extif0_cfg = {
-+ .mode = RTL8367_EXTIF_MODE_RGMII,
-+ .txdelay = 1,
-+ .rxdelay = 5,
-+ .ability = {
-+ .force_mode = 1,
-+ .txpause = 1,
-+ .rxpause = 1,
-+ .link = 1,
-+ .duplex = 1,
-+ .speed = RTL8367_PORT_SPEED_1000,
-+ },
-+};
-+
-+static struct rtl8367_platform_data nb6_rtl8367_data = {
-+ .gpio_sda = NB6_GPIO_RTL8367_SDA,
-+ .gpio_sck = NB6_GPIO_RTL8367_SCK,
-+ .extif0_cfg = &nb6_rtl8367_extif0_cfg,
-+};
-+
-+static struct platform_device nb6_rtl8367_device = {
-+ .name = RTL8367_DRIVER_NAME,
-+ .id = -1,
-+ .dev = {
-+ .platform_data = &nb6_rtl8367_data,
-+ }
-+};
-+
-+static struct platform_device * __initdata nb6_devices[] = {
-+ &nb6_rtl8367_device,
-+};
-+
-+static struct board_info __initdata board_nb6 = {
-+ .name = "NB6",
-+ .expected_cpu_id = 0x6362,
-+
-+ .has_uart0 = 1,
-+
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+
-+ .has_enetsw = 1,
-+
-+ .enetsw = {
-+ .used_ports = {
-+ [4] = {
-+ .used = 1,
-+ .phy_id = 0xff,
-+ .bypass_link = 1,
-+ .force_speed = 1000,
-+ .force_duplex_full = 1,
-+ .name = "RGMII",
-+ },
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 24,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ .active_low = 1,
-+ },
-+ {
-+ .desc = "wps",
-+ .gpio = 25,
-+ .type = EV_KEY,
-+ .code = KEY_WPS_BUTTON,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ .active_low = 1,
-+ },
-+ {
-+ .desc = "wlan",
-+ .gpio = 12,
-+ .type = EV_KEY,
-+ .code = KEY_WLAN,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ .active_low = 1,
-+ },
-+ {
-+ .desc = "service",
-+ .gpio = 10,
-+ .type = EV_KEY,
-+ .code = BTN_0,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .devs = nb6_devices,
-+ .num_devs = ARRAY_SIZE(nb6_devices),
-+};
-+#endif
-+
- /*
- * known 6368 boards
- */
-@@ -2828,6 +2928,10 @@ static const struct board_info __initcon
- &board_DVAG3810BN,
- #endif
-
-+#ifdef CONFIG_BCM63XX_CPU_6362
-+ &board_nb6,
-+#endif
-+
- #ifdef CONFIG_BCM63XX_CPU_6368
- &board_96368mvwg,
- &board_96368mvngr,
-@@ -2895,6 +2999,11 @@ static void __init boardid_fixup(u8 *boo
- }
- }
-
-+ if (BCMCPU_IS_6362() && (!strncmp(board_name, "NB6-", sizeof("NB6-") - 1))) {
-+ board_name[sizeof("NB6") - 1] = '\0';
-+ return ;
-+ }
-+
- /* check if bcm_tag is at 64k offset */
- if (strncmp(board_name, tag->board_id, BOARDID_LEN) != 0) {
- /* else try 128k */
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1033,6 +1033,57 @@ static struct board_info __initdata boar
- .has_ehci0 = 1,
- };
-
-+static struct board_info __initdata board_FAST2604 = {
-+ .name = "F@ST2604",
-+ .expected_cpu_id = 0x6348,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+ .has_ohci0 = 1,
-+
-+ .has_enet1 = 1,
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "F@ST2604:green:power",
-+ .gpio = 0,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "F@ST2604:red:power",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "F@ST2604:red:inet",
-+ .gpio = 4,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "F@ST2604:green:wps",
-+ .gpio = 5,
-+ .active_low = 1,
-+ },
-+ },
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 33,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
- static struct board_info __initdata board_rta1025w_16 = {
- .name = "RTA1025W_16",
- .expected_cpu_id = 0x6348,
-@@ -2896,6 +2947,7 @@ static const struct board_info __initcon
- &board_96348gw_10,
- &board_96348gw_11,
- &board_FAST2404,
-+ &board_FAST2604,
- &board_DV201AMR,
- &board_96348gw_a,
- &board_rta1025w_16,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -217,6 +217,125 @@ static struct board_info __initdata boar
- },
- };
-
-+static struct board_info __initdata board_963281T_TEF = {
-+ .name = "963281T_TEF",
-+ .expected_cpu_id = 0x6328,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+ .has_enetsw = 1,
-+
-+ .enetsw = {
-+ .used_ports = {
-+ [0] = {
-+ .used = 1,
-+ .phy_id = 1,
-+ .name = "Port 1",
-+ },
-+ [1] = {
-+ .used = 1,
-+ .phy_id = 2,
-+ .name = "Port 2",
-+ },
-+ [2] = {
-+ .used = 1,
-+ .phy_id = 3,
-+ .name = "Port 3",
-+ },
-+ [3] = {
-+ .used = 1,
-+ .phy_id = 4,
-+ .name = "Port 4",
-+ },
-+ },
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "963281T_TEF:green:power",
-+ .gpio = 4,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "963281T_TEF:red:power",
-+ .gpio = 8,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281T_TEF:green:inet",
-+ .gpio = 11,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281T_TEF:red:inet",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281T_TEF:green:ppp",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281T_TEF:red:ppp",
-+ .gpio = 5,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281T_TEF:green:3g",
-+ .gpio = 6,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281T_TEF:red:3g",
-+ .gpio = 7,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281T_TEF:green:wlan",
-+ .gpio = 9,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281T_TEF:red:wlan",
-+ .gpio = 10,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281T_TEF:green:eth",
-+ .gpio = 31,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "963281T_TEF:red:eth",
-+ .gpio = 20,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 23,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wlan",
-+ .gpio = 24,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_WLAN,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
- static struct board_info __initdata board_dsl_274xb_f1 = {
- .name = "AW4339U",
- .expected_cpu_id = 0x6328,
-@@ -2928,6 +3047,7 @@ static const struct board_info __initcon
- #ifdef CONFIG_BCM63XX_CPU_6328
- &board_96328avng,
- &board_963281TAN,
-+ &board_963281T_TEF,
- &board_dsl_274xb_f1,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6338
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -147,6 +147,78 @@ static struct board_info __initdata boar
- },
- };
-
-+static struct board_info __initdata board_96328A_1441N1 = {
-+ .name = "96328A-1441N1",
-+ .expected_cpu_id = 0x6328,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+ .has_enetsw = 1,
-+
-+ .enetsw = {
-+ .used_ports = {
-+ [0] = {
-+ .used = 1,
-+ .phy_id = 1,
-+ .name = "Port 1",
-+ },
-+ [1] = {
-+ .used = 1,
-+ .phy_id = 2,
-+ .name = "Port 2",
-+ },
-+ [2] = {
-+ .used = 1,
-+ .phy_id = 3,
-+ .name = "Port 3",
-+ },
-+ [3] = {
-+ .used = 1,
-+ .phy_id = 4,
-+ .name = "Port 4",
-+ },
-+ },
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "96328A-1441N1:green:power",
-+ .gpio = 8,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "96328A-1441N1:red:power",
-+ .gpio = 4,
-+ },
-+ {
-+ .name = "96328A-1441N1:green:inet",
-+ .gpio = 7,
-+ },
-+ {
-+ .name = "96328A-1441N1:red:inet",
-+ .gpio = 1,
-+ },
-+ {
-+ .name = "96328A-1441N1:green:dsl",
-+ .gpio = 11,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 23,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
- static struct board_info __initdata board_963281TAN = {
- .name = "963281TAN",
- .expected_cpu_id = 0x6328,
-@@ -3046,6 +3118,7 @@ static struct board_info __initdata boar
- static const struct board_info __initconst *bcm963xx_boards[] = {
- #ifdef CONFIG_BCM63XX_CPU_6328
- &board_96328avng,
-+ &board_96328A_1441N1,
- &board_963281TAN,
- &board_963281T_TEF,
- &board_dsl_274xb_f1,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -147,6 +147,72 @@ static struct board_info __initdata boar
- },
- };
-
-+static struct board_info __initdata board_96328A_1241N = {
-+ .name = "96328A-1241N",
-+ .expected_cpu_id = 0x6328,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+ .has_enetsw = 1,
-+
-+ .enetsw = {
-+ .used_ports = {
-+ [0] = {
-+ .used = 1,
-+ .phy_id = 1,
-+ .name = "Port 1",
-+ },
-+ [1] = {
-+ .used = 1,
-+ .phy_id = 2,
-+ .name = "Port 2",
-+ },
-+ [2] = {
-+ .used = 1,
-+ .phy_id = 3,
-+ .name = "Port 3",
-+ },
-+ [3] = {
-+ .used = 1,
-+ .phy_id = 4,
-+ .name = "Port 4",
-+ },
-+ },
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "96328A-1241N:green:power",
-+ .gpio = 4,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "96328A-1241N:red:alarm",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "96328A-1241N:green:inet",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 23,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
- static struct board_info __initdata board_96328A_1441N1 = {
- .name = "96328A-1441N1",
- .expected_cpu_id = 0x6328,
-@@ -3118,6 +3184,7 @@ static struct board_info __initdata boar
- static const struct board_info __initconst *bcm963xx_boards[] = {
- #ifdef CONFIG_BCM63XX_CPU_6328
- &board_96328avng,
-+ &board_96328A_1241N,
- &board_96328A_1441N1,
- &board_963281TAN,
- &board_963281T_TEF,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -752,6 +752,55 @@ static struct board_info __initdata boar
-
- .has_uart0 = 1,
- };
-+
-+static struct board_info __initdata board_rta770bw = {
-+ .name = "RTA770BW",
-+ .expected_cpu_id = 0x6345,
-+
-+ .has_uart0 = 1,
-+
-+ .has_enet0 = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "RTA770BW:green:usb",
-+ .gpio = 7,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "RTA770BW:green:adsl",
-+ .gpio = 8,
-+ },
-+ {
-+ .name = "RTA770BW:green:diag",
-+ .gpio = 10,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "RTA770BW:green:wlan",
-+ .gpio = 11,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 13,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -3198,6 +3247,7 @@ static const struct board_info __initcon
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6345
- &board_96345gw2,
-+ &board_rta770bw,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6348
- &board_96348r,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -2858,6 +2858,374 @@ static struct board_info __initdata boar
- },
- };
-
-+static struct board_info __initdata board_HW556 = {
-+ .name = "HW556",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+
-+ .has_caldata = 1,
-+ .caldata = {
-+ {
-+ .caldata_offset = 0xe00000,
-+ },
-+ },
-+
-+ .has_enet1 = 1,
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "HW556:red:message",
-+ .gpio = 0,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:hspa",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:dsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:power",
-+ .gpio = 3,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "HW556:red:all",
-+ .gpio = 6,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "help",
-+ .gpio = 8,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_HELP,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wlan",
-+ .gpio = 9,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_WLAN,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "restart",
-+ .gpio = 10,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "reset",
-+ .gpio = 11,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_CONFIG,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+static struct board_info __initdata board_HW556_A = {
-+ .name = "HW556_A",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+
-+ .has_caldata = 1,
-+ .caldata = {
-+ {
-+ .vendor = PCI_VENDOR_ID_RALINK,
-+ .caldata_offset = 0xeffe00,
-+ .slot = 1,
-+ .eeprom = "rt2x00.eeprom",
-+ },
-+ },
-+
-+ .has_enet1 = 1,
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "HW556:red:message",
-+ .gpio = 0,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:hspa",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:dsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:power",
-+ .gpio = 3,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "HW556:red:all",
-+ .gpio = 6,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "help",
-+ .gpio = 8,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_HELP,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wlan",
-+ .gpio = 9,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_WLAN,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "restart",
-+ .gpio = 10,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "reset",
-+ .gpio = 11,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_CONFIG,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+static struct board_info __initdata board_HW556_B = {
-+ .name = "HW556_B",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+
-+ .has_caldata = 1,
-+ .caldata = {
-+ {
-+ .vendor = PCI_VENDOR_ID_ATHEROS,
-+ .caldata_offset = 0xf7e000,
-+ .slot = 1,
-+ .endian_check = 1,
-+ .led_pin = 2,
-+ },
-+ },
-+
-+ .has_enet1 = 1,
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "HW556:red:message",
-+ .gpio = 0,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:hspa",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:dsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:power",
-+ .gpio = 3,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "HW556:red:all",
-+ .gpio = 6,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "help",
-+ .gpio = 8,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_HELP,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wlan",
-+ .gpio = 9,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_WLAN,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "restart",
-+ .gpio = 10,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "reset",
-+ .gpio = 11,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_CONFIG,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+static struct board_info __initdata board_HW556_C = {
-+ .name = "HW556_C",
-+ .expected_cpu_id = 0x6358,
-+
-+ .has_uart0 = 1,
-+ .has_pci = 1,
-+ .has_ohci0 = 1,
-+ .has_ehci0 = 1,
-+
-+ .has_caldata = 1,
-+ .caldata = {
-+ {
-+ .vendor = PCI_VENDOR_ID_ATHEROS,
-+ .caldata_offset = 0xefe000,
-+ .slot = 1,
-+ .endian_check = 1,
-+ .led_pin = 2,
-+ },
-+ },
-+
-+ .has_enet1 = 1,
-+ .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "HW556:red:message",
-+ .gpio = 0,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:hspa",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:dsl",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "HW556:red:power",
-+ .gpio = 3,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "HW556:red:all",
-+ .gpio = 6,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "help",
-+ .gpio = 8,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_HELP,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wlan",
-+ .gpio = 9,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_WLAN,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "restart",
-+ .gpio = 10,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "reset",
-+ .gpio = 11,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_CONFIG,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
-+
- /* T-Home Speedport W 303V Typ B */
- static struct board_info __initdata board_spw303v = {
- .name = "96358-502V",
-@@ -3286,6 +3654,10 @@ static const struct board_info __initcon
- &board_nb4_fxc_r2,
- &board_ct6373_1,
- &board_HW553,
-+ &board_HW556,
-+ &board_HW556_A,
-+ &board_HW556_B,
-+ &board_HW556_C,
- &board_spw303v,
- &board_DVAG3810BN,
- #endif
-@@ -3351,13 +3723,37 @@ static void __init boardid_fixup(u8 *boo
- struct bcm_tag *tag = (struct bcm_tag *)(boot_addr + CFE_OFFSET_64K);
- char *board_name = (char *)bcm63xx_nvram_get_name();
-
-- if (BCMCPU_IS_6358() && (!strcmp(board_name, "96358VW"))) {
-- u8 *p = boot_addr + NB4_PID_OFFSET;
--
-- /* Extract nb4 PID */
-- if (!memcmp(p, "NB4-", 4)) {
-- memcpy(board_name, p, sizeof("NB4-XXX-rX"));
-- return;
-+ if (BCMCPU_IS_6358()) {
-+ if (!strcmp(board_name, "96358VW")) {
-+ u8 *p = boot_addr + NB4_PID_OFFSET;
-+
-+ /* Extract nb4 PID */
-+ if (!memcmp(p, "NB4-", 4)) {
-+ memcpy(board_name, p, sizeof("NB4-XXX-rX"));
-+ return;
-+ }
-+ } else if (!strcmp(board_name, "HW556")) {
-+ /*
-+ * HW556 has different wlan caldatas depending on
-+ * hardware version.
-+ * Detect hardware version and change board id
-+ */
-+ u8 cal_data_ath9k[4] = { 0xa5, 0x5a, 0, 0 };
-+ u8 cal_data_rt3062[4] = { 0x62, 0x30, 1, 0 };
-+
-+ if (!memcmp(boot_addr + 0xeffe00,
-+ &cal_data_rt3062, 4)) {
-+ /* Ralink 0xeffe00 */
-+ memcpy(board_name, "HW556_A", 7);
-+ } else if (!memcmp(boot_addr + 0xf7e000,
-+ &cal_data_ath9k, 4)) {
-+ /* Atheros 0xf7e000 */
-+ memcpy(board_name, "HW556_B", 7);
-+ } else if (!memcmp(boot_addr + 0xefe000,
-+ &cal_data_ath9k, 4)) {
-+ /* Atheros 0xefe000 */
-+ memcpy(board_name, "HW556_C", 7);
-+ }
- }
- }
-
---- a/drivers/mtd/bcm63xxpart.c
-+++ b/drivers/mtd/bcm63xxpart.c
-@@ -70,6 +70,11 @@ static int bcm63xx_parse_cfe_partitions(
- BCM63XX_CFE_BLOCK_SIZE);
-
- cfelen = cfe_erasesize;
-+
-+ /* Fix HW556 MX29LV128DB */
-+ if (!strncmp(bcm63xx_nvram_get_name(), "HW556", 5))
-+ cfelen = 0x20000;
-+
- nvramlen = bcm63xx_nvram_get_psi_size();
- nvramlen = roundup(nvramlen, cfe_erasesize);
- nvramaddr = master->size - nvramlen;
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -801,6 +801,60 @@ static struct board_info __initdata boar
- },
- },
- };
-+
-+// Actually this board is the very same as the rta770bw,
-+// where the additional 'b' within the name just
-+// just indicates 'Annex B'. The ADSL Modem itself is able
-+// to handle both Annex A as well as Annex B -
-+// the loaded firmware makes the only difference
-+static struct board_info __initdata board_rta770w = {
-+ .name = "RTA770W",
-+ .expected_cpu_id = 0x6345,
-+
-+ .has_uart0 = 1,
-+
-+ .has_enet0 = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
-+ .force_speed_100 = 1,
-+ .force_duplex_full = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "RTA770W:green:usb",
-+ .gpio = 7,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "RTA770W:green:adsl",
-+ .gpio = 8,
-+ },
-+ {
-+ .name = "RTA770W:green:diag",
-+ .gpio = 10,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "RTA770W:green:wlan",
-+ .gpio = 11,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 13,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .active_low = 1,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
-+};
- #endif
-
- /*
-@@ -3616,6 +3670,7 @@ static const struct board_info __initcon
- #ifdef CONFIG_BCM63XX_CPU_6345
- &board_96345gw2,
- &board_rta770bw,
-+ &board_rta770w,
- #endif
- #ifdef CONFIG_BCM63XX_CPU_6348
- &board_96348r,
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -2058,6 +2058,99 @@ static struct board_info __initdata boar
-
- .has_ohci0 = 1,
- .has_ehci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "AGPF-S0:red:power",
-+ .gpio = 5,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:green:power",
-+ .gpio = 4,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "AGPF-S0:red:service",
-+ .gpio = 7,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:green:service",
-+ .gpio = 6,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:green:adsl",
-+ .gpio = 9,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:red:adsl",
-+ .gpio = 10,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:red:wifi",
-+ .gpio = 23,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:green:wifi",
-+ .gpio = 22,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:green:internet",
-+ .gpio = 25,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:red:internet",
-+ .gpio = 24,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:red:usr1",
-+ .gpio = 27,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:green:usr1",
-+ .gpio = 26,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:red:usr2",
-+ .gpio = 30,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "AGPF-S0:green:usr2",
-+ .gpio = 29,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 37,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wps",
-+ .gpio = 34,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_WPS_BUTTON,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
- };
-
- static struct board_info __initdata board_DWVS0 = {
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -1503,6 +1503,19 @@ static struct board_info __initdata boar
- },
-
- .has_ohci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "96348GW-A::adsl",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "96348GW-A::usb",
-+ .gpio = 0,
-+ .active_low = 1,
-+ }
-+ },
- };
-
- static struct board_info __initdata board_96348_D4PW = {
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -963,6 +963,17 @@ static struct board_info __initdata boar
- .active_low = 1,
- },
- },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 6,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
- };
-
- static struct board_info __initdata board_96348gw_11 = {
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -591,6 +591,8 @@ static struct board_info __initdata boar
- .has_uart0 = 1,
- .has_enet0 = 1,
- .enet0 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -634,6 +636,8 @@ static struct board_info __initdata boar
- .has_uart0 = 1,
- .has_enet0 = 1,
- .enet0 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -919,6 +923,8 @@ static struct board_info __initdata boar
- .use_internal_phy = 1,
- },
- .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -991,6 +997,8 @@ static struct board_info __initdata boar
- },
-
- .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -1220,6 +1228,8 @@ static struct board_info __initdata boar
- .use_internal_phy = 1,
- },
- .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -1395,6 +1405,8 @@ static struct board_info __initdata boar
- },
-
- .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -1469,6 +1481,8 @@ static struct board_info __initdata boar
- .use_internal_phy = 1,
- },
- .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -1490,6 +1504,8 @@ static struct board_info __initdata boar
- .use_internal_phy = 1,
- },
- .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -1509,6 +1525,8 @@ static struct board_info __initdata boar
- .use_internal_phy = 1,
- },
- .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -1884,6 +1902,8 @@ static struct board_info __initdata boar
- },
-
- .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -1936,6 +1956,8 @@ static struct board_info __initdata boar
- },
-
- .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -2076,6 +2098,8 @@ static struct board_info __initdata boar
- },
-
- .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
-@@ -2193,6 +2217,8 @@ static struct board_info __initdata boar
- },
-
- .enet1 = {
-+ .has_phy = 1,
-+ .phy_id = 0,
- .force_speed_100 = 1,
- .force_duplex_full = 1,
- },
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -2225,6 +2225,94 @@ static struct board_info __initdata boar
-
- .has_ohci0 = 1,
- .has_ehci0 = 1,
-+
-+ .leds = {
-+ {
-+ .name = "DWV-S0:red:power",
-+ .gpio = 5,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DWV-S0:green:power",
-+ .gpio = 4,
-+ .active_low = 1,
-+ .default_trigger = "default-on",
-+ },
-+ {
-+ .name = "DWV-S0:red:internet",
-+ .gpio = 6,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DWV-S0:green:internet",
-+ .gpio = 7,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DWV-S0:green:ADSL",
-+ .gpio = 2,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DWV-S0:red:ADSL",
-+ .gpio = 12,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DWV-S0:red:wifi",
-+ .gpio = 10,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DWV-S0:green:VoIP",
-+ .gpio = 9,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DWV-S0:red:VoIP",
-+ .gpio = 0,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DWV-S0:red:ethernet",
-+ .gpio = 1,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DWV-S0:green:ethernet",
-+ .gpio = 8,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DWV-S0:red:USB",
-+ .gpio = 11,
-+ .active_low = 1,
-+ },
-+ {
-+ .name = "DWV-S0:green:USB",
-+ .gpio = 3,
-+ .active_low = 1,
-+ },
-+ },
-+
-+ .buttons = {
-+ {
-+ .desc = "reset",
-+ .gpio = 37,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_RESTART,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ {
-+ .desc = "wps",
-+ .gpio = 34,
-+ .active_low = 1,
-+ .type = EV_KEY,
-+ .code = KEY_WPS_BUTTON,
-+ .debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
-+ },
-+ },
- };
-
- /* D-Link DSL-274xB revison C2/C3 */
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -69,6 +69,41 @@
- static struct board_info board;
-
- /*
-+ * known 3368 boards
-+ */
-+#ifdef CONFIG_BCM63XX_CPU_3368
-+static struct board_info __initdata board_cvg834g = {
-+ .name = "CVG834G_E15R3921",
-+ .expected_cpu_id = 0x3368,
-+
-+ .has_uart0 = 1,
-+ .has_uart1 = 1,
-+
-+ .has_enet0 = 1,
-+ .has_pci = 1,
-+
-+ .enet0 = {
-+ .has_phy = 1,
-+ .use_internal_phy = 1,
-+ },
-+
-+ .leds = {
-+ {
-+ .name = "CVG834G::switch-reset",
-+ .gpio = 36,
-+ .default_trigger= "default-on",
-+ },
-+
-+ {
-+ .name = "CVG834G:green:power",
-+ .gpio = 37,
-+ .default_trigger= "default-on",
-+ },
-+ },
-+};
-+#endif
-+
-+/*
- * known 6328 boards
- */
- #ifdef CONFIG_BCM63XX_CPU_6328
-@@ -3884,6 +3919,9 @@ static struct board_info __initdata boar
- * all boards
- */
- static const struct board_info __initconst *bcm963xx_boards[] = {
-+#ifdef CONFIG_BCM63XX_CPU_3368
-+ &board_cvg834g,
-+#endif
- #ifdef CONFIG_BCM63XX_CPU_6328
- &board_96328avng,
- &board_96328A_1241N,
+++ /dev/null
---- a/arch/mips/bcm63xx/nvram.c
-+++ b/arch/mips/bcm63xx/nvram.c
-@@ -41,6 +41,13 @@ struct bcm963xx_nvram {
- static struct bcm963xx_nvram nvram;
- static int mac_addr_used;
-
-+/*
-+ * Required export for WL
-+ */
-+#define NVRAM_SPACE 0x8000
-+char nvram_buf[NVRAM_SPACE];
-+EXPORT_SYMBOL(nvram_buf);
-+
- void __init bcm63xx_nvram_init(void *addr)
- {
- unsigned int check_len;
-@@ -48,6 +55,7 @@ void __init bcm63xx_nvram_init(void *add
-
- /* extract nvram data */
- memcpy(&nvram, addr, sizeof(nvram));
-+ memcpy(&nvram_buf, addr, NVRAM_SPACE);
-
- /* check checksum before using data */
- if (nvram.version <= 4) {
---- a/arch/mips/mm/cache.c
-+++ b/arch/mips/mm/cache.c
-@@ -58,6 +58,7 @@ void (*_dma_cache_wback)(unsigned long s
- void (*_dma_cache_inv)(unsigned long start, unsigned long size);
-
- EXPORT_SYMBOL(_dma_cache_wback_inv);
-+EXPORT_SYMBOL(_dma_cache_inv);
-
- #endif /* CONFIG_DMA_NONCOHERENT */
-
+++ /dev/null
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -14,6 +14,7 @@
- #include <linux/ssb/ssb.h>
- #include <linux/gpio_keys.h>
- #include <linux/input.h>
-+#include <linux/export.h>
- #include <linux/spi/spi.h>
- #include <linux/spi/spi_gpio.h>
- #include <linux/spi/74x164.h>
-@@ -4001,7 +4002,7 @@ static const struct board_info __initcon
- * bcm4318 WLAN work
- */
- #ifdef CONFIG_SSB_PCIHOST
--static struct ssb_sprom bcm63xx_sprom = {
-+struct ssb_sprom bcm63xx_sprom = {
- .revision = 0x02,
- .board_rev = 0x17,
- .country_code = 0x0,
-@@ -4021,6 +4022,7 @@ static struct ssb_sprom bcm63xx_sprom =
- .boardflags_lo = 0x2848,
- .boardflags_hi = 0x0000,
- };
-+EXPORT_SYMBOL(bcm63xx_sprom);
-
- int bcm63xx_get_fallback_sprom(struct ssb_bus *bus, struct ssb_sprom *out)
- {
+++ /dev/null
-From e3208e6087642b95a5bab3101fc9c6e34892c861 Mon Sep 17 00:00:00 2001
-From: Miguel GAIO <miguel.gaio@efixo.com>
-Date: Fri, 6 Jul 2012 14:12:33 +0200
-Subject: [PATCH 6/8] * [rtl8367r] Fix RGMII support
-
----
- drivers/net/phy/rtl8367.c | 5 +++++
- 1 files changed, 5 insertions(+), 0 deletions(-)
-
---- a/drivers/net/phy/rtl8367.c
-+++ b/drivers/net/phy/rtl8367.c
-@@ -146,6 +146,10 @@
- #define RTL8367_EXT_RGMXF_TXDELAY_MASK 1
- #define RTL8367_EXT_RGMXF_RXDELAY_MASK 0x7
-
-+#define RTL8367_PHY_AD_REG 0x130f
-+#define RTL8370_PHY_AD_DUMMY_1_OFFSET 5
-+#define RTL8370_PHY_AD_DUMMY_1_MASK 0xe0
-+
- #define RTL8367_DI_FORCE_REG(_x) (0x1310 + (_x))
- #define RTL8367_DI_FORCE_MODE BIT(12)
- #define RTL8367_DI_FORCE_NWAY BIT(7)
-@@ -894,6 +898,7 @@ static int rtl8367_extif_set_mode(struct
- case RTL8367_EXTIF_MODE_RGMII_33V:
- REG_WR(smi, RTL8367_CHIP_DEBUG0_REG, 0x0367);
- REG_WR(smi, RTL8367_CHIP_DEBUG1_REG, 0x7777);
-+ REG_RMW(smi, RTL8367_PHY_AD_REG, BIT(5), 0);
- break;
-
- case RTL8367_EXTIF_MODE_TMII_MAC:
projects / openwrt / staging / xback.git / commitdiff