glinet_gl-s1300 \
linksys_ea8300 \
linksys_whw03v2 \
+ netgear_wax218 \
nokia_ac400i \
p2w_r619ac \
pakedge_wr-1 \
$(eval $(call generate-ipq-wifi-package,glinet_gl-s1300,GL.iNet GL-S1300))
$(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300))
$(eval $(call generate-ipq-wifi-package,linksys_whw03v2,Linksys WHW03 V2))
+$(eval $(call generate-ipq-wifi-package,netgear_wax218,Netgear WAX218))
$(eval $(call generate-ipq-wifi-package,nokia_ac400i,Nokia AC400i))
$(eval $(call generate-ipq-wifi-package,p2w_r619ac,P&W R619AC))
$(eval $(call generate-ipq-wifi-package,pakedge_wr-1,Pakedge WR-1))
--- /dev/null
+/dts-v1/;
+
+#include "ipq8074.dtsi"
+#include "ipq8074-hk-cpu.dtsi"
+#include "ipq8074-ess.dtsi"
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Netgear WAX218";
+ compatible = "netgear,wax218", "qcom,ipq8074";
+
+ aliases {
+ serial0 = &blsp1_uart5;
+ led-boot = &led_power_amber;
+ led-failsafe = &led_power_amber;
+ led-running = &led_power_amber;
+ led-upgrade = &led_power_amber;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ /*
+ * Netgear's U-Boot adds "ubi.mtd=rootfs root=mtd:ubi_rootfs"
+ * That fails to create a UBI block device, so add it here.
+ */
+ bootargs-append = " ubi.block=0,rootfs root=/dev/ubiblock0_1";
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 52 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ led_spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sck-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&tlmm 19 GPIO_ACTIVE_HIGH>;
+
+ led_gpio: led_gpio@0 {
+ compatible = "fairchild,74hc595";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ registers-number = <1>;
+ enable-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>;
+ spi-max-frequency = <1000000>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power_amber: led_power {
+ label = "amber:power";
+ gpios = <&led_gpio 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_lan {
+ label = "blue:lan";
+ gpios = <&led_gpio 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_wlan_2g {
+ label = "blue:wlan2g";
+ gpios = <&led_gpio 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_wlan_5g {
+ label = "blue:wlan5g";
+ gpios = <&led_gpio 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&edma {
+ status = "okay";
+};
+
+&switch {
+ status = "okay";
+
+ switch_cpu_bmp = <0x1>;
+ switch_lan_bmp = <0x3e>;
+ switch_wan_bmp = <0x40>;
+ switch_mac_mode = <0x00>;
+ switch_mac_mode1 = <0xff>;
+ switch_mac_mode2 = <0x0f>;
+ bm_tick_mode = <0>;
+ tm_tick_mode = <0>;
+
+ qcom,port_phyinfo {
+ port@5 {
+ port_id = <6>;
+ phy_address = <28>;
+ port_mac_sel = "QGMAC_PORT";
+ };
+ };
+};
+
+&tlmm {
+ mdio_pins: mdio-pins {
+ mdc {
+ pins = "gpio68";
+ function = "mdc";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ mdio {
+ pins = "gpio69";
+ function = "mdio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>;
+
+ qca8081_28: ethernet-phy@28 {
+ reg = <28>;
+ };
+};
+
+&dp6_syn {
+ status = "okay";
+ phy-handle = <&qca8081_28>;
+ label = "lan";
+ nvmem-cells = <&macaddr_ubootenv_ethaddr>;
+ nvmem-cell-names = "mac-address-ascii";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&qpic_nand {
+ status = "okay";
+
+ nand@0 {
+ reg = <0>;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ nand-bus-width = <8>;
+
+ partitions {
+ compatible = "qcom,smem-part";
+
+ partition-0-appsblenv {
+ compatible = "fixed-partitions";
+ label = "0:appsblenv";
+ read-only;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ compatible = "u-boot,env";
+ label = "env-data";
+ reg = <0x0 0x40000>;
+
+ macaddr_ubootenv_ethaddr: ethaddr {};
+ };
+ };
+ };
+ };
+};
+
+&blsp1_uart5 {
+ status = "okay";
+};
+
+&wifi {
+ status = "okay";
+
+ qcom,ath11k-calibration-variant = "Netgear-WAX218";
+};
endef
TARGET_DEVICES += edimax_cax1800
+define Device/netgear_wax218
+ $(call Device/FitImage)
+ $(call Device/UbiFit)
+ ARTIFACTS := web-ui-factory.fit
+ DEVICE_VENDOR := Netgear
+ DEVICE_MODEL := WAX218
+ DEVICE_DTS_CONFIG := config@hk07
+ BLOCKSIZE := 128k
+ PAGESIZE := 2048
+ SOC := ipq8072
+ ARTIFACT/web-ui-factory.fit := append-image initramfs-uImage.itb | \
+ ubinize-kernel | qsdk-ipq-factory-nand
+ DEVICE_PACKAGES := kmod-spi-gpio kmod-spi-bitbang kmod-gpio-nxp-74hc164 \
+ ipq-wifi-netgear_wax218
+endef
+TARGET_DEVICES += netgear_wax218
+
define Device/qnap_301w
$(call Device/FitImage)
DEVICE_VENDOR := QNAP
projects / openwrt / staging / dangole.git / commitdiff