--- /dev/null
+/*
+ * x86 FPU boot time init code:
+ */
+#include <asm/fpu/internal.h>
+#include <asm/tlbflush.h>
+
+/*
+ * Initialize the TS bit in CR0 according to the style of context-switches
+ * we are using:
+ */
+static void fpu__init_cpu_ctx_switch(void)
+{
+ if (!cpu_has_eager_fpu)
+ stts();
+ else
+ clts();
+}
+
+/*
+ * Initialize the registers found in all CPUs, CR0 and CR4:
+ */
+static void fpu__init_cpu_generic(void)
+{
+ unsigned long cr0;
+ unsigned long cr4_mask = 0;
+
+ if (cpu_has_fxsr)
+ cr4_mask |= X86_CR4_OSFXSR;
+ if (cpu_has_xmm)
+ cr4_mask |= X86_CR4_OSXMMEXCPT;
+ if (cr4_mask)
+ cr4_set_bits(cr4_mask);
+
+ cr0 = read_cr0();
+ cr0 &= ~(X86_CR0_TS|X86_CR0_EM); /* clear TS and EM */
+ if (!cpu_has_fpu)
+ cr0 |= X86_CR0_EM;
+ write_cr0(cr0);
+
+ /* Flush out any pending x87 state: */
+ asm volatile ("fninit");
+}
+
+/*
+ * Enable all supported FPU features. Called when a CPU is brought online:
+ */
+void fpu__init_cpu(void)
+{
+ fpu__init_cpu_generic();
+ fpu__init_cpu_xstate();
+ fpu__init_cpu_ctx_switch();
+}
+
+/*
+ * The earliest FPU detection code.
+ *
+ * Set the X86_FEATURE_FPU CPU-capability bit based on
+ * trying to execute an actual sequence of FPU instructions:
+ */
+static void fpu__init_system_early_generic(struct cpuinfo_x86 *c)
+{
+ unsigned long cr0;
+ u16 fsw, fcw;
+
+ fsw = fcw = 0xffff;
+
+ cr0 = read_cr0();
+ cr0 &= ~(X86_CR0_TS | X86_CR0_EM);
+ write_cr0(cr0);
+
+ asm volatile("fninit ; fnstsw %0 ; fnstcw %1"
+ : "+m" (fsw), "+m" (fcw));
+
+ if (fsw == 0 && (fcw & 0x103f) == 0x003f)
+ set_cpu_cap(c, X86_FEATURE_FPU);
+ else
+ clear_cpu_cap(c, X86_FEATURE_FPU);
+
+#ifndef CONFIG_MATH_EMULATION
+ if (!cpu_has_fpu) {
+ pr_emerg("x86/fpu: Giving up, no FPU found and no math emulation present\n");
+ for (;;)
+ asm volatile("hlt");
+ }
+#endif
+}
+
+/*
+ * Boot time FPU feature detection code:
+ */
+unsigned int mxcsr_feature_mask __read_mostly = 0xffffffffu;
+
+static void __init fpu__init_system_mxcsr(void)
+{
+ unsigned int mask = 0;
+
+ if (cpu_has_fxsr) {
+ struct fxregs_state fx_tmp __aligned(32) = { };
+
+ asm volatile("fxsave %0" : "+m" (fx_tmp));
+
+ mask = fx_tmp.mxcsr_mask;
+
+ /*
+ * If zero then use the default features mask,
+ * which has all features set, except the
+ * denormals-are-zero feature bit:
+ */
+ if (mask == 0)
+ mask = 0x0000ffbf;
+ }
+ mxcsr_feature_mask &= mask;
+}
+
+/*
+ * Once per bootup FPU initialization sequences that will run on most x86 CPUs:
+ */
+static void __init fpu__init_system_generic(void)
+{
+ /*
+ * Set up the legacy init FPU context. (xstate init might overwrite this
+ * with a more modern format, if the CPU supports it.)
+ */
+ fpstate_init_fxstate(&init_fpstate.fxsave);
+
+ fpu__init_system_mxcsr();
+}
+
+/*
+ * Size of the FPU context state. All tasks in the system use the
+ * same context size, regardless of what portion they use.
+ * This is inherent to the XSAVE architecture which puts all state
+ * components into a single, continuous memory block:
+ */
+unsigned int xstate_size;
+EXPORT_SYMBOL_GPL(xstate_size);
+
+/*
+ * Set up the xstate_size based on the legacy FPU context size.
+ *
+ * We set this up first, and later it will be overwritten by
+ * fpu__init_system_xstate() if the CPU knows about xstates.
+ */
+static void __init fpu__init_system_xstate_size_legacy(void)
+{
+ static int on_boot_cpu = 1;
+
+ WARN_ON_FPU(!on_boot_cpu);
+ on_boot_cpu = 0;
+
+ /*
+ * Note that xstate_size might be overwriten later during
+ * fpu__init_system_xstate().
+ */
+
+ if (!cpu_has_fpu) {
+ /*
+ * Disable xsave as we do not support it if i387
+ * emulation is enabled.
+ */
+ setup_clear_cpu_cap(X86_FEATURE_XSAVE);
+ setup_clear_cpu_cap(X86_FEATURE_XSAVEOPT);
+ xstate_size = sizeof(struct swregs_state);
+ } else {
+ if (cpu_has_fxsr)
+ xstate_size = sizeof(struct fxregs_state);
+ else
+ xstate_size = sizeof(struct fregs_state);
+ }
++ /*
++ * Quirk: we don't yet handle the XSAVES* instructions
++ * correctly, as we don't correctly convert between
++ * standard and compacted format when interfacing
++ * with user-space - so disable it for now.
++ *
++ * The difference is small: with recent CPUs the
++ * compacted format is only marginally smaller than
++ * the standard FPU state format.
++ *
++ * ( This is easy to backport while we are fixing
++ * XSAVES* support. )
++ */
++ setup_clear_cpu_cap(X86_FEATURE_XSAVES);
+}
+
+/*
+ * FPU context switching strategies:
+ *
+ * Against popular belief, we don't do lazy FPU saves, due to the
+ * task migration complications it brings on SMP - we only do
+ * lazy FPU restores.
+ *
+ * 'lazy' is the traditional strategy, which is based on setting
+ * CR0::TS to 1 during context-switch (instead of doing a full
+ * restore of the FPU state), which causes the first FPU instruction
+ * after the context switch (whenever it is executed) to fault - at
+ * which point we lazily restore the FPU state into FPU registers.
+ *
+ * Tasks are of course under no obligation to execute FPU instructions,
+ * so it can easily happen that another context-switch occurs without
+ * a single FPU instruction being executed. If we eventually switch
+ * back to the original task (that still owns the FPU) then we have
+ * not only saved the restores along the way, but we also have the
+ * FPU ready to be used for the original task.
+ *
+ * 'eager' switching is used on modern CPUs, there we switch the FPU
+ * state during every context switch, regardless of whether the task
+ * has used FPU instructions in that time slice or not. This is done
+ * because modern FPU context saving instructions are able to optimize
+ * state saving and restoration in hardware: they can detect both
+ * unused and untouched FPU state and optimize accordingly.
+ *
+ * [ Note that even in 'lazy' mode we might optimize context switches
+ * to use 'eager' restores, if we detect that a task is using the FPU
+ * frequently. See the fpu->counter logic in fpu/internal.h for that. ]
+ */
+static enum { AUTO, ENABLE, DISABLE } eagerfpu = AUTO;
+
+static int __init eager_fpu_setup(char *s)
+{
+ if (!strcmp(s, "on"))
+ eagerfpu = ENABLE;
+ else if (!strcmp(s, "off"))
+ eagerfpu = DISABLE;
+ else if (!strcmp(s, "auto"))
+ eagerfpu = AUTO;
+ return 1;
+}
+__setup("eagerfpu=", eager_fpu_setup);
+
+/*
+ * Pick the FPU context switching strategy:
+ */
+static void __init fpu__init_system_ctx_switch(void)
+{
+ static bool on_boot_cpu = 1;
+
+ WARN_ON_FPU(!on_boot_cpu);
+ on_boot_cpu = 0;
+
+ WARN_ON_FPU(current->thread.fpu.fpstate_active);
+ current_thread_info()->status = 0;
+
+ /* Auto enable eagerfpu for xsaveopt */
+ if (cpu_has_xsaveopt && eagerfpu != DISABLE)
+ eagerfpu = ENABLE;
+
+ if (xfeatures_mask & XSTATE_EAGER) {
+ if (eagerfpu == DISABLE) {
+ pr_err("x86/fpu: eagerfpu switching disabled, disabling the following xstate features: 0x%llx.\n",
+ xfeatures_mask & XSTATE_EAGER);
+ xfeatures_mask &= ~XSTATE_EAGER;
+ } else {
+ eagerfpu = ENABLE;
+ }
+ }
+
+ if (eagerfpu == ENABLE)
+ setup_force_cpu_cap(X86_FEATURE_EAGER_FPU);
+
+ printk(KERN_INFO "x86/fpu: Using '%s' FPU context switches.\n", eagerfpu == ENABLE ? "eager" : "lazy");
+}
+
+/*
+ * Called on the boot CPU once per system bootup, to set up the initial
+ * FPU state that is later cloned into all processes:
+ */
+void __init fpu__init_system(struct cpuinfo_x86 *c)
+{
+ fpu__init_system_early_generic(c);
+
+ /*
+ * The FPU has to be operational for some of the
+ * later FPU init activities:
+ */
+ fpu__init_cpu();
+
+ /*
+ * But don't leave CR0::TS set yet, as some of the FPU setup
+ * methods depend on being able to execute FPU instructions
+ * that will fault on a set TS, such as the FXSAVE in
+ * fpu__init_system_mxcsr().
+ */
+ clts();
+
+ fpu__init_system_generic();
+ fpu__init_system_xstate_size_legacy();
+ fpu__init_system_xstate();
+
+ fpu__init_system_ctx_switch();
+}
+
+/*
+ * Boot parameter to turn off FPU support and fall back to math-emu:
+ */
+static int __init no_387(char *s)
+{
+ setup_clear_cpu_cap(X86_FEATURE_FPU);
+ return 1;
+}
+__setup("no387", no_387);
+
+/*
+ * Disable all xstate CPU features:
+ */
+static int __init x86_noxsave_setup(char *s)
+{
+ if (strlen(s))
+ return 0;
+
+ setup_clear_cpu_cap(X86_FEATURE_XSAVE);
+ setup_clear_cpu_cap(X86_FEATURE_XSAVEOPT);
+ setup_clear_cpu_cap(X86_FEATURE_XSAVES);
+ setup_clear_cpu_cap(X86_FEATURE_AVX);
+ setup_clear_cpu_cap(X86_FEATURE_AVX2);
+
+ return 1;
+}
+__setup("noxsave", x86_noxsave_setup);
+
+/*
+ * Disable the XSAVEOPT instruction specifically:
+ */
+static int __init x86_noxsaveopt_setup(char *s)
+{
+ setup_clear_cpu_cap(X86_FEATURE_XSAVEOPT);
+
+ return 1;
+}
+__setup("noxsaveopt", x86_noxsaveopt_setup);
+
+/*
+ * Disable the XSAVES instruction:
+ */
+static int __init x86_noxsaves_setup(char *s)
+{
+ setup_clear_cpu_cap(X86_FEATURE_XSAVES);
+
+ return 1;
+}
+__setup("noxsaves", x86_noxsaves_setup);
+
+/*
+ * Disable FX save/restore and SSE support:
+ */
+static int __init x86_nofxsr_setup(char *s)
+{
+ setup_clear_cpu_cap(X86_FEATURE_FXSR);
+ setup_clear_cpu_cap(X86_FEATURE_FXSR_OPT);
+ setup_clear_cpu_cap(X86_FEATURE_XMM);
+
+ return 1;
+}
+__setup("nofxsr", x86_nofxsr_setup);
projects / openwrt / staging / blogic.git / commitdiff