* tasklet function.
*
* NOTE: If the driver opts to use the _irqsafe() functions, it may not also
- * use the non-irqsafe functions!
+ * use the non-IRQ-safe functions!
*/
/**
* struct ieee80211_ht_bss_info - describing BSS's HT characteristics
*
* This structure describes most essential parameters needed
- * to describe 802.11n HT characteristics in a BSS
+ * to describe 802.11n HT characteristics in a BSS.
*
* @primary_channel: channel number of primery channel
* @bss_cap: 802.11n's general BSS capabilities (e.g. channel width)
};
/**
- * enum mac80211_tx_flags - flags to transmission information/status
+ * enum mac80211_tx_control_flags - flags to describe transmission information/status
*
- * These flags are used with the @flags member of &ieee80211_tx_info
+ * These flags are used with the @flags member of &ieee80211_tx_info.
*
* @IEEE80211_TX_CTL_REQ_TX_STATUS: request TX status callback for this frame.
* @IEEE80211_TX_CTL_DO_NOT_ENCRYPT: send this frame without encryption;
* @IEEE80211_TX_CTL_USE_CTS_PROTECT: use CTS protection for the frame (e.g.,
* for combined 802.11g / 802.11b networks)
* @IEEE80211_TX_CTL_NO_ACK: tell the low level not to wait for an ack
- * @IEEE80211_TX_CTL_RATE_CTRL_PROBE
+ * @IEEE80211_TX_CTL_RATE_CTRL_PROBE: TBD
* @IEEE80211_TX_CTL_CLEAR_PS_FILT: clear powersave filter for destination
* station
- * @IEEE80211_TX_CTL_REQUEUE:
+ * @IEEE80211_TX_CTL_REQUEUE: TBD
* @IEEE80211_TX_CTL_FIRST_FRAGMENT: this is a first fragment of the frame
+ * @IEEE80211_TX_CTL_SHORT_PREAMBLE: TBD
* @IEEE80211_TX_CTL_LONG_RETRY_LIMIT: this frame should be send using the
* through set_retry_limit configured long retry value
* @IEEE80211_TX_CTL_EAPOL_FRAME: internal to mac80211
* @IEEE80211_TX_CTL_40_MHZ_WIDTH: send this frame using 40 Mhz channel width
* @IEEE80211_TX_CTL_DUP_DATA: duplicate data frame on both 20 Mhz channels
* @IEEE80211_TX_CTL_SHORT_GI: send this frame using short guard interval
+ * @IEEE80211_TX_CTL_INJECTED: TBD
* @IEEE80211_TX_STAT_TX_FILTERED: The frame was not transmitted
* because the destination STA was in powersave mode.
* @IEEE80211_TX_STAT_ACK: Frame was acknowledged
* (3) TX status information - driver tells mac80211 what happened
*
* @flags: transmit info flags, defined above
+ * @band: TBD
+ * @tx_rate_idx: TBD
+ * @antenna_sel_tx: TBD
+ * @control: union for control data
+ * @status: union for status data
+ * @driver_data: array of driver_data pointers
* @retry_count: number of retries
* @excessive_retries: set to 1 if the frame was retried many times
* but not acknowledged
/**
* enum ieee80211_key_len - key length
- * @WEP40: WEP 5 byte long key
- * @WEP104: WEP 13 byte long key
+ * @LEN_WEP40: WEP 5-byte long key
+ * @LEN_WEP104: WEP 13-byte long key
*/
enum ieee80211_key_len {
LEN_WEP40 = 5,
* enum sta_notify_cmd - sta notify command
*
* Used with the sta_notify() callback in &struct ieee80211_ops, this
- * indicates addition and removal of a station to station table
+ * indicates addition and removal of a station to station table.
*
* @STA_NOTIFY_ADD: a station was added to the station table
* @STA_NOTIFY_REMOVE: a station being removed from the station table
*
* This function frees everything that was allocated, including the
* private data for the driver. You must call ieee80211_unregister_hw()
- * before calling this function
+ * before calling this function.
*
* @hw: the hardware to free
*/
struct sk_buff *skb);
/**
- * ieee80211_tx_status_irqsafe - irq-safe transmit status callback
+ * ieee80211_tx_status_irqsafe - IRQ-safe transmit status callback
*
* Like ieee80211_tx_status() but can be called in IRQ context
* (internally defers to a tasklet.)
* @keyconf: the parameter passed with the set key
* @skb: the skb for which the key is needed
* @rc4key: a buffer to which the key will be written
+ * @type: TBD
+ * @key: TBD
*/
void ieee80211_get_tkip_key(struct ieee80211_key_conf *keyconf,
struct sk_buff *skb,
void ieee80211_scan_completed(struct ieee80211_hw *hw);
/**
- * ieee80211_iterate_active_interfaces- iterate active interfaces
+ * ieee80211_iterate_active_interfaces - iterate active interfaces
*
* This function iterates over the interfaces associated with a given
* hardware that are currently active and calls the callback for them.
*
* This function must be called by low level driver once it has
* finished with preparations for the BA session.
- * This version of the function is irq safe.
+ * This version of the function is IRQ-safe.
*/
void ieee80211_start_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra,
u16 tid);
*
* This function must be called by low level driver once it has
* finished with preparations for the BA session tear down.
- * This version of the function is irq safe.
+ * This version of the function is IRQ-safe.
*/
void ieee80211_stop_tx_ba_cb_irqsafe(struct ieee80211_hw *hw, const u8 *ra,
u16 tid);
/**
* ieee80211_notify_mac - low level driver notification
* @hw: pointer as obtained from ieee80211_alloc_hw().
- * @notification_types: enum ieee80211_notification_types
+ * @notif_type: enum ieee80211_notification_types
*
* This function must be called by low level driver to inform mac80211 of
* low level driver status change or force mac80211 to re-assoc for low
* @list: global linked list entry
* @hnext: hash table linked list pointer
* @local: pointer to the global information
+ * @sdata: TBD
+ * @key: TBD
+ * @rate_ctrl: TBD
+ * @rate_ctrl_priv: TBD
+ * @lock: used for locking all fields that require locking, see comments
+ * in the header file.
+ * @flaglock: spinlock for flags accesses
+ * @ht_info: HT capabilities of this STA
+ * @supp_rates: Bitmap of supported rates (per band)
* @addr: MAC address of this STA
* @aid: STA's unique AID (1..2007, 0 = not assigned yet),
* only used in AP (and IBSS?) mode
+ * @listen_interval: TBD
+ * @pin_status: TBD
* @flags: STA flags, see &enum ieee80211_sta_info_flags
- * @flaglock: spinlock for flags accesses
* @ps_tx_buf: buffer of frames to transmit to this station
* when it leaves power saving state
* @tx_filtered: buffer of frames we already tried to transmit
* power saving state
* @rx_packets: Number of MSDUs received from this STA
* @rx_bytes: Number of bytes received from this STA
- * @supp_rates: Bitmap of supported rates (per band)
- * @ht_info: HT capabilities of this STA
- * @lock: used for locking all fields that require locking, see comments
- * in the header file.
+ * @wep_weak_iv_count: TBD
+ * @last_rx: TBD
+ * @num_duplicates: number of duplicate frames received from this STA
+ * @rx_fragments: number of received MPDUs
+ * @rx_dropped: number of dropped MPDUs from this STA
+ * @last_signal: signal of last received frame from this STA
+ * @last_qual: qual of last received frame from this STA
+ * @last_noise: noise of last received frame from this STA
+ * @last_seq_ctrl: last received seq/frag number from this STA (per RX queue)
+ * @wme_rx_queue: TBD
+ * @tx_filtered_count: TBD
+ * @tx_retry_failed: TBD
+ * @tx_retry_count: TBD
+ * @tx_num_consecutive_failures: TBD
+ * @tx_num_mpdu_ok: TBD
+ * @tx_num_mpdu_fail: TBD
+ * @fail_avg: moving percentage of failed MSDUs
+ * @tx_packets: number of RX/TX MSDUs
+ * @tx_bytes: TBD
+ * @tx_fragments: number of transmitted MPDUs
+ * @txrate_idx: TBD
+ * @last_txrate_idx: TBD
+ * @wme_tx_queue: TBD
+ * @ampdu_mlme: TBD
+ * @timer_to_tid: identity mapping to ID timers
+ * @tid_to_tx_q: map tid to tx queue
+ * @llid: Local link ID
+ * @plid: Peer link ID
+ * @reason: Cancel reason on PLINK_HOLDING state
+ * @plink_retries: Retries in establishment
+ * @ignore_plink_timer: TBD
+ * @plink_state plink_state: TBD
+ * @plink_timeout: TBD
+ * @plink_timer: TBD
+ * @debugfs: debug filesystem info
*/
struct sta_info {
/* General information, mostly static */
unsigned long rx_packets, rx_bytes;
unsigned long wep_weak_iv_count;
unsigned long last_rx;
- unsigned long num_duplicates; /* number of duplicate frames received
- * from this STA */
- unsigned long rx_fragments; /* number of received MPDUs */
- unsigned long rx_dropped; /* number of dropped MPDUs from this STA */
- int last_signal; /* signal of last received frame from this STA */
- int last_qual; /* qual of last received frame from this STA */
- int last_noise; /* noise of last received frame from this STA */
- /* last received seq/frag number from this STA (per RX queue) */
+ unsigned long num_duplicates;
+ unsigned long rx_fragments;
+ unsigned long rx_dropped;
+ int last_signal;
+ int last_qual;
+ int last_noise;
__le16 last_seq_ctrl[NUM_RX_DATA_QUEUES];
#ifdef CONFIG_MAC80211_DEBUG_COUNTERS
unsigned int wme_rx_queue[NUM_RX_DATA_QUEUES];
unsigned int fail_avg;
/* Updated from TX path only, no locking requirements */
- unsigned long tx_packets; /* number of RX/TX MSDUs */
+ unsigned long tx_packets;
unsigned long tx_bytes;
- unsigned long tx_fragments; /* number of transmitted MPDUs */
+ unsigned long tx_fragments;
int txrate_idx;
int last_txrate_idx;
#ifdef CONFIG_MAC80211_DEBUG_COUNTERS
* Aggregation information, locked with lock.
*/
struct sta_ampdu_mlme ampdu_mlme;
- u8 timer_to_tid[STA_TID_NUM]; /* identity mapping to ID timers */
- u8 tid_to_tx_q[STA_TID_NUM]; /* map tid to tx queue */
+ u8 timer_to_tid[STA_TID_NUM];
+ u8 tid_to_tx_q[STA_TID_NUM];
#ifdef CONFIG_MAC80211_MESH
/*
* Mesh peer link attributes
* TODO: move to a sub-structure that is referenced with pointer?
*/
- __le16 llid; /* Local link ID */
- __le16 plid; /* Peer link ID */
- __le16 reason; /* Cancel reason on PLINK_HOLDING state */
- u8 plink_retries; /* Retries in establishment */
+ __le16 llid;
+ __le16 plid;
+ __le16 reason;
+ u8 plink_retries;
bool ignore_plink_timer;
enum plink_state plink_state;
u32 plink_timeout;
projects / openwrt / staging / blogic.git / commitdiff