Ubiquiti EdgeRouter 6P is 6 port router with similar
specifications as the EdgeRouter 4, support for which was added
in commit
dd651e54cc5eadba480a56a7d2c18471e560f491
There are five 10/100/1000 Mbps RJ/Copper ports and
one 1000 Mbps SFP port.
SoC: Octeon Cavium 7130 (Cavium 3) at 1000MHz
Memory: 1GiB DDR3
Flash: 2x2M chips with uboots (chainloaded) + 512K eeprom
LEDs: 1x for power status (white/blue, controllable)
and 6x for ethernet and SFP ports (no control over them)
Buttons: 1x Reset
Serial: 1x RJ45 port on front panel. 115200 baud, 8N1
USB: 1x USB3.0 on front panel
MII: 1x QSGMII from SoC
PHY: 1x Vitesse VSC8504 of which 4 ports are used (phys 4-7)
1x Vitesse VSC8514 of which 2 ports are used (phys 8-9)
Network port mapping
- eth0 on device maps to lan0 and phy5
- eth1 on device maps to lan1 and phy6
- eth2 on device maps to lan2 and phy7
- eth3 on device maps to lan3 and phy8
- eth4 on device maps to lan4 and phy9
- eth5 (SFP) on device maps to lan5 and phy4
What is not working:
- There is no port status available before it goes up
- SFP have no additional status and presented as no different from eth
- Power-over-ethernet (passive) support has not been tested
How to flash the firmware:
- copy openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin and
openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar to
USB flash drive that is formatted to vfat/fat32
- connect USB flash drive to EdgeRouter 6P front USB port
- connect serial cable using front RJ45 port (115200 baud, 8N1)
- connect power to cable to EdgeRouter 6P
- connect terminal to the console to see uboot boot process
- interrupt boot by pressing button(s) on your keyboard to log
in to the uboot
- detect usb connected flash drives by typing to the console:
usb start
- after drive is detected load initramfs+kernel to the memory by typing:
fatload usb 0:1 0x20000000 openwrt-octeon-ubnt_edgerouter-6p-initramfs-kernel.bin
- after initramfs+kernel is loaded to the memory load it by typing:
bootoctlinux 0 numcores=4 endbootargs mem=0
- boot process should finish and you will be greeted with console
after pressing enter
- create directory to mount usb flash drive to by typing:
mkdir /tmp/sda
- mount flash drive to that directory by typing:
mount /dev/sda1 /tmp/sda
- flash firmware to router internal storage by typing:
sysupgrade /tmp/sda/openwrt-octeon-ubnt_edgerouter-6p-squashfs-sysupgrade.tar
- device will reboot and after it gets up you will have
edgerouter 6p running openwrt
Signed-off-by: Dan Brown <danbrown@gmail.com>
[reorder/squash patches, move ethernet@0 to DTS, share image setup]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ubnt,edgerouter-4)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "lan0"
;;
+ubnt,edgerouter-6p)
+ ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "lan0"
+ ;;
*)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
itus,shield-router)
move_config "/dev/mmcblk1p1"
;;
- ubnt,edgerouter-4)
+ ubnt,edgerouter-4 | \
+ ubnt,edgerouter-6p)
move_config "/dev/mmcblk0p1"
;;
esac
cp -af "$UPGRADE_BACKUP" "/mnt/$BACKUP_FILE"
umount /mnt
;;
- ubnt,edgerouter-4)
+ ubnt,edgerouter-4 | \
+ ubnt,edgerouter-6p)
mount -t vfat /dev/mmcblk0p1 /mnt
cp -af "$UPGRADE_BACKUP" "/mnt/$BACKUP_FILE"
umount /mnt
[ -b "${rootfs}" ] || return 1
case "$board" in
er | \
- ubnt,edgerouter-4)
+ ubnt,edgerouter-4 | \
+ ubnt,edgerouter-6p)
kernel=mmcblk0p1
;;
erlite)
er | \
erlite | \
itus,shield-router | \
- ubnt,edgerouter-4)
+ ubnt,edgerouter-4 | \
+ ubnt,edgerouter-6p)
local kernel_length=$(tar xf $tar_file $board_dir/kernel -O | wc -c 2> /dev/null)
local rootfs_length=$(tar xf $tar_file $board_dir/root -O | wc -c 2> /dev/null)
[ "$kernel_length" = 0 -o "$rootfs_length" = 0 ] && {
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "cn7130_ubnt_edgerouter-e300.dtsi"
+
+/ {
+ compatible = "ubnt,edgerouter-6p", "cavium,cn7130";
+ model = "Ubiquiti EdgeRouter 6P";
+};
+
+&smi0 {
+ phy8: ethernet-phy@8 {
+ device_type = "ethernet-phy";
+ interrupts = <17 8>;
+ interrupt-parent = <&gpio>;
+ compatible = "vitesse,vsc8514", "ethernet-phy-ieee802.3-c22";
+ reg = <8>;
+ };
+
+ phy9: ethernet-phy@9 {
+ device_type = "ethernet-phy";
+ interrupts = <17 8>;
+ interrupt-parent = <&gpio>;
+ compatible = "vitesse,vsc8514", "ethernet-phy-ieee802.3-c22";
+ reg = <9>;
+ };
+};
+
+&pip {
+ interface@0 {
+ ethernet@0 {
+ label = "lan5";
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&phy4>;
+ mtd-mac-address = <&eeprom 0>;
+ };
+ };
+
+ interface@1 {
+ status = "okay";
+
+ ethernet@0 {
+ label = "lan3";
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&phy8>;
+ mtd-mac-address = <&eeprom 0>;
+ mtd-mac-address-increment = <(4)>;
+ };
+
+ ethernet@1 {
+ label = "lan4";
+ status = "okay";
+ phy-mode = "sgmii";
+ phy-handle = <&phy9>;
+ mtd-mac-address = <&eeprom 0>;
+ mtd-mac-address-increment = <(5)>;
+ };
+ };
+};
endef
TARGET_DEVICES += ubnt_edgerouter
-define Device/ubnt_edgerouter-4
+define Device/ubnt_edgerouter-e300
DEVICE_VENDOR := Ubiquiti
- DEVICE_MODEL := EdgeRouter 4
- DEVICE_DTS := cn7130_ubnt_edgerouter-4
DEVICE_PACKAGES += kmod-gpio-button-hotplug kmod-leds-gpio kmod-of-mdio kmod-sfp kmod-usb3 kmod-usb-dwc3 kmod-usb-storage-uas
KERNEL := kernel-bin | patch-cmdline | append-dtb-to-elf
KERNEL_DEPENDS := $$(wildcard $(DTS_DIR)/$(DEVICE_DTS).dts)
CMDLINE := root=/dev/mmcblk0p2 rootfstype=squashfs,ext4 rootwait
endef
+
+define Device/ubnt_edgerouter-4
+ $(Device/ubnt_edgerouter-e300)
+ DEVICE_MODEL := EdgeRouter 4
+ DEVICE_DTS := cn7130_ubnt_edgerouter-4
+endef
TARGET_DEVICES += ubnt_edgerouter-4
+define Device/ubnt_edgerouter-6p
+ $(Device/ubnt_edgerouter-e300)
+ DEVICE_MODEL := EdgeRouter 6P
+ DEVICE_DTS := cn7130_ubnt_edgerouter-6p
+endef
+TARGET_DEVICES += ubnt_edgerouter-6p
+
ERLITE_CMDLINE:=-mtdparts=phys_mapped_flash:512k(boot0)ro,512k(boot1)ro,64k(eeprom)ro root=/dev/sda2 rootfstype=squashfs,ext4 rootwait
define Device/ubnt_edgerouter-lite
DEVICE_VENDOR := Ubiquiti
projects / openwrt / staging / jow.git / commitdiff