dt-bindings: PCI: meson: Update PCIE bindings documentation

Now that a new PHYs has been introduced for AXG SoC family, update
dt bindings documentation.

Please note that this breaks backward compatibility but as not a single
devicetree uses that yet that seems ok.

Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>

diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
index 84fdc422792ef7d1f4cf019e025d39d54bb3a905..b6acbe694ffb2d30f66e6fb0c81082a79444aa84 100644 (file)
--- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
@@ -18,7 +18,6 @@ Required properties:
 - reg-names: Must be
        - "elbi"        External local bus interface registers
        - "cfg"         Meson specific registers
-       - "phy"         Meson PCIE PHY registers for AXG SoC Family
        - "config"      PCIe configuration space
 - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
 - clocks: Must contain an entry for each entry in clock-names.
@@ -26,13 +25,13 @@ Required properties:
        - "pclk"       PCIe GEN 100M PLL clock
        - "port"       PCIe_x(A or B) RC clock gate
        - "general"    PCIe Phy clock
-       - "mipi"       PCIe_x(A or B) 100M ref clock gate for AXG SoC Family
 - resets: phandle to the reset lines.
-- reset-names: must contain "phy" "port" and "apb"
-       - "phy"         Share PHY reset for AXG SoC Family
+- reset-names: must contain "port" and "apb"
        - "port"        Port A or B reset
        - "apb"         Share APB reset
-- phys: should contain a phandle to the shared phy for G12A SoC Family
+- phys: should contain a phandle to the PCIE phy
+- phy-names: must contain "pcie"
+
 - device_type:
        should be "pci". As specified in designware-pcie.txt
 
@@ -43,9 +42,8 @@ Example configuration:
                        compatible = "amlogic,axg-pcie", "snps,dw-pcie";
                        reg = <0x0 0xf9800000 0x0 0x400000
                                        0x0 0xff646000 0x0 0x2000
-                                       0x0 0xff644000 0x0 0x2000
                                        0x0 0xf9f00000 0x0 0x100000>;
-                       reg-names = "elbi", "cfg", "phy", "config";
+                       reg-names = "elbi", "cfg", "config";
                        reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
                        interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
                        #interrupt-cells = <1>;
@@ -58,17 +56,15 @@ Example configuration:
                        ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
 
                        clocks = <&clkc CLKID_USB
-                                       &clkc CLKID_MIPI_ENABLE
                                        &clkc CLKID_PCIE_A
                                        &clkc CLKID_PCIE_CML_EN0>;
                        clock-names = "general",
-                                       "mipi",
                                        "pclk",
                                        "port";
-                       resets = <&reset RESET_PCIE_PHY>,
-                               <&reset RESET_PCIE_A>,
+                       resets = <&reset RESET_PCIE_A>,
                                <&reset RESET_PCIE_APB>;
-                       reset-names = "phy",
-                                       "port",
+                       reset-names = "port",
                                        "apb";
+                       phys = <&pcie_phy>;
+                       phy-names = "pcie";
        };