--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "xiaomi,mi-router-3-pro", "mediatek,mt7621-soc";
+ model = "Xiaomi Mi Router 3 Pro";
+
+ aliases {
+ led-boot = &led_status_yellow;
+ led-failsafe = &led_status_red;
+ led-running = &led_status_blue;
+ led-upgrade = &led_status_yellow;
+ label-mac-device = &gmac0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_red: status_red {
+ label = "red:status";
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_blue: status_blue {
+ label = "blue:status";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_yellow: status_yellow {
+ label = "yellow:status";
+ gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
+ };
+
+ wan_amber {
+ label = "amber:wan";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "dsa-0.0:04:1Gbps";
+ };
+
+ lan3_amber {
+ label = "amber:lan3";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "dsa-0.0:01:1Gbps";
+ };
+
+ lan2_amber {
+ label = "amber:lan2";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "dsa-0.0:02:1Gbps";
+ };
+
+ lan1_amber {
+ label = "amber:lan1";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "dsa-0.0:03:1Gbps";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ reg_usb_vbus: regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&xhci {
+ vbus-supply = <®_usb_vbus>;
+};
+
+&nand {
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "Bootloader";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "Config";
+ reg = <0x40000 0x40000>;
+ };
+
+ partition@80000 {
+ label = "Bdata";
+ reg = <0x80000 0x40000>;
+ read-only;
+ };
+
+ factory: partition@c0000 {
+ label = "factory";
+ reg = <0x0c0000 0x40000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "crash";
+ reg = <0x100000 0x40000>;
+ };
+
+ partition@140000 {
+ label = "crash_syslog";
+ reg = <0x140000 0x80000>;
+ };
+
+ partition@1c0000 {
+ label = "reserved0";
+ reg = <0x1c0000 0x40000>;
+ read-only;
+ };
+
+ /* We keep stock xiaomi firmware (kernel0) here */
+ partition@200000 {
+ label = "kernel_stock";
+ reg = <0x200000 0x400000>;
+ };
+
+ partition@600000 {
+ label = "kernel";
+ reg = <0x600000 0x400000>;
+ };
+
+ partition@a00000 {
+ label = "ubi";
+ reg = <0xa00000 0xf580000>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi@0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x0000>;
+ ieee80211-freq-limit = <2400000 2500000>;
+ };
+};
+
+&pcie1 {
+ wifi@0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ };
+};
+
+&gmac0 {
+ mtd-mac-address = <&factory 0xe006>;
+};
+
+&switch0 {
+ ports {
+ port@1 {
+ status = "okay";
+ label = "lan3";
+ };
+
+ port@2 {
+ status = "okay";
+ label = "lan2";
+ };
+
+ port@3 {
+ status = "okay";
+ label = "lan1";
+ };
+
+ port@4 {
+ status = "okay";
+ label = "wan";
+ mtd-mac-address = <&factory 0xe000>;
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "jtag", "uart2", "uart3", "wdt";
+ function = "gpio";
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621_xiaomi_mi-router-4a-3g-v2.dtsi"
+
+/ {
+ compatible = "xiaomi,mi-router-3g-v2", "mediatek,mt7621-soc";
+ model = "Xiaomi Mi Router 3G v2";
+};
--- /dev/null
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "xiaomi,mi-router-3g", "mediatek,mt7621-soc";
+ model = "Xiaomi Mi Router 3G";
+
+ aliases {
+ led-boot = &led_status_yellow;
+ led-failsafe = &led_status_red;
+ led-running = &led_status_blue;
+ led-upgrade = &led_status_yellow;
+ label-mac-device = &gmac0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_red: status_red {
+ label = "red:status";
+ gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_blue: status_blue {
+ label = "blue:status";
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_yellow: status_yellow {
+ label = "yellow:status";
+ gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
+ };
+
+ wan_amber {
+ label = "amber:wan";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "dsa-0.0:01:1Gbps";
+ };
+
+ lan1_amber {
+ label = "amber:lan1";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "dsa-0.0:03:1Gbps";
+ };
+
+ lan2_amber {
+ label = "amber:lan2";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "dsa-0.0:02:1Gbps";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ reg_usb_vbus: regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio 12 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&xhci {
+ vbus-supply = <®_usb_vbus>;
+};
+
+&nand {
+ status = "okay";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "Bootloader";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "Config";
+ reg = <0x80000 0x40000>;
+ };
+
+ partition@c0000 {
+ label = "Bdata";
+ reg = <0xc0000 0x40000>;
+ read-only;
+ };
+
+ factory: partition@100000 {
+ label = "factory";
+ reg = <0x100000 0x40000>;
+ read-only;
+ };
+
+ partition@140000 {
+ label = "crash";
+ reg = <0x140000 0x40000>;
+ };
+
+ partition@180000 {
+ label = "crash_syslog";
+ reg = <0x180000 0x40000>;
+ };
+
+ partition@1c0000 {
+ label = "reserved0";
+ reg = <0x1c0000 0x40000>;
+ read-only;
+ };
+
+ /* uboot expects to find kernels at 0x200000 & 0x600000
+ * referred to as system 1 & system 2 respectively.
+ * a kernel is considered suitable for handing control over
+ * if its linux magic number exists & uImage CRC are correct.
+ * If either of those conditions fail, a matching sys'n'_fail flag
+ * is set in uboot env & a restart performed in the hope that the
+ * alternate kernel is okay.
+ * if neither kernel checksums ok and both are marked failed, system 2
+ * is booted anyway.
+ *
+ * Note uboot's tftp flash install writes the transferred
+ * image to both kernel partitions.
+ */
+
+ partition@200000 {
+ label = "kernel_stock";
+ reg = <0x200000 0x400000>;
+ };
+
+ partition@600000 {
+ label = "kernel";
+ reg = <0x600000 0x400000>;
+ };
+
+ /* ubi partition is the result of squashing
+ * next consecutive stock partitions:
+ * - rootfs0 (rootfs partition for stock kernel0),
+ * - rootfs1 (rootfs partition for stock failsafe kernel1),
+ * - overlay (used as ubi overlay in stock fw)
+ * resulting 117,5MiB space for packages.
+ */
+
+ partition@a00000 {
+ label = "ubi";
+ reg = <0xa00000 0x7580000>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi@0,0 {
+ compatible = "pci14c3,7603";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x0000>;
+ ieee80211-freq-limit = <2400000 2500000>;
+ };
+};
+
+&pcie1 {
+ wifi@0,0 {
+ compatible = "pci14c3,7662";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ };
+};
+
+&gmac0 {
+ mtd-mac-address = <&factory 0xe006>;
+};
+
+&switch0 {
+ ports {
+ port@1 {
+ status = "okay";
+ label = "wan";
+ mtd-mac-address = <&factory 0xe000>;
+ };
+
+ port@2 {
+ status = "okay";
+ label = "lan2";
+ };
+
+ port@3 {
+ status = "okay";
+ label = "lan1";
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "jtag", "uart2", "uart3", "wdt";
+ function = "gpio";
+ };
+};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "mt7621_xiaomi_mi-router-4a-3g-v2.dtsi"
-
-/ {
- compatible = "xiaomi,mir3g-v2", "mediatek,mt7621-soc";
- model = "Xiaomi Mi Router 3G v2";
-};
+++ /dev/null
-#include "mt7621.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
- compatible = "xiaomi,mir3g", "mediatek,mt7621-soc";
- model = "Xiaomi Mi Router 3G";
-
- aliases {
- led-boot = &led_status_yellow;
- led-failsafe = &led_status_red;
- led-running = &led_status_blue;
- led-upgrade = &led_status_yellow;
- label-mac-device = &gmac0;
- };
-
- chosen {
- bootargs = "console=ttyS0,115200n8";
- };
-
- leds {
- compatible = "gpio-leds";
-
- led_status_red: status_red {
- label = "red:status";
- gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
- };
-
- led_status_blue: status_blue {
- label = "blue:status";
- gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
- };
-
- led_status_yellow: status_yellow {
- label = "yellow:status";
- gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
- };
-
- wan_amber {
- label = "amber:wan";
- gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "dsa-0.0:01:1Gbps";
- };
-
- lan1_amber {
- label = "amber:lan1";
- gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "dsa-0.0:03:1Gbps";
- };
-
- lan2_amber {
- label = "amber:lan2";
- gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "dsa-0.0:02:1Gbps";
- };
- };
-
- keys {
- compatible = "gpio-keys";
-
- reset {
- label = "reset";
- gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
- };
-
- reg_usb_vbus: regulator {
- compatible = "regulator-fixed";
- regulator-name = "usb_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio 12 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-};
-
-&xhci {
- vbus-supply = <®_usb_vbus>;
-};
-
-&nand {
- status = "okay";
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "Bootloader";
- reg = <0x0 0x80000>;
- read-only;
- };
-
- partition@80000 {
- label = "Config";
- reg = <0x80000 0x40000>;
- };
-
- partition@c0000 {
- label = "Bdata";
- reg = <0xc0000 0x40000>;
- read-only;
- };
-
- factory: partition@100000 {
- label = "factory";
- reg = <0x100000 0x40000>;
- read-only;
- };
-
- partition@140000 {
- label = "crash";
- reg = <0x140000 0x40000>;
- };
-
- partition@180000 {
- label = "crash_syslog";
- reg = <0x180000 0x40000>;
- };
-
- partition@1c0000 {
- label = "reserved0";
- reg = <0x1c0000 0x40000>;
- read-only;
- };
-
- /* uboot expects to find kernels at 0x200000 & 0x600000
- * referred to as system 1 & system 2 respectively.
- * a kernel is considered suitable for handing control over
- * if its linux magic number exists & uImage CRC are correct.
- * If either of those conditions fail, a matching sys'n'_fail flag
- * is set in uboot env & a restart performed in the hope that the
- * alternate kernel is okay.
- * if neither kernel checksums ok and both are marked failed, system 2
- * is booted anyway.
- *
- * Note uboot's tftp flash install writes the transferred
- * image to both kernel partitions.
- */
-
- partition@200000 {
- label = "kernel_stock";
- reg = <0x200000 0x400000>;
- };
-
- partition@600000 {
- label = "kernel";
- reg = <0x600000 0x400000>;
- };
-
- /* ubi partition is the result of squashing
- * next consecutive stock partitions:
- * - rootfs0 (rootfs partition for stock kernel0),
- * - rootfs1 (rootfs partition for stock failsafe kernel1),
- * - overlay (used as ubi overlay in stock fw)
- * resulting 117,5MiB space for packages.
- */
-
- partition@a00000 {
- label = "ubi";
- reg = <0xa00000 0x7580000>;
- };
- };
-};
-
-&pcie {
- status = "okay";
-};
-
-&pcie0 {
- wifi@0,0 {
- compatible = "pci14c3,7603";
- reg = <0x0000 0 0 0 0>;
- mediatek,mtd-eeprom = <&factory 0x0000>;
- ieee80211-freq-limit = <2400000 2500000>;
- };
-};
-
-&pcie1 {
- wifi@0,0 {
- compatible = "pci14c3,7662";
- reg = <0x0000 0 0 0 0>;
- mediatek,mtd-eeprom = <&factory 0x8000>;
- ieee80211-freq-limit = <5000000 6000000>;
- };
-};
-
-&gmac0 {
- mtd-mac-address = <&factory 0xe006>;
-};
-
-&switch0 {
- ports {
- port@1 {
- status = "okay";
- label = "wan";
- mtd-mac-address = <&factory 0xe000>;
- };
-
- port@2 {
- status = "okay";
- label = "lan2";
- };
-
- port@3 {
- status = "okay";
- label = "lan1";
- };
- };
-};
-
-&state_default {
- gpio {
- groups = "jtag", "uart2", "uart3", "wdt";
- function = "gpio";
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "mt7621.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-/ {
- compatible = "xiaomi,mir3p", "mediatek,mt7621-soc";
- model = "Xiaomi Mi Router 3 Pro";
-
- aliases {
- led-boot = &led_status_yellow;
- led-failsafe = &led_status_red;
- led-running = &led_status_blue;
- led-upgrade = &led_status_yellow;
- label-mac-device = &gmac0;
- };
-
- chosen {
- bootargs = "console=ttyS0,115200n8";
- };
-
- leds {
- compatible = "gpio-leds";
-
- led_status_red: status_red {
- label = "red:status";
- gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
- };
-
- led_status_blue: status_blue {
- label = "blue:status";
- gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
- };
-
- led_status_yellow: status_yellow {
- label = "yellow:status";
- gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
- };
-
- wan_amber {
- label = "amber:wan";
- gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "dsa-0.0:04:1Gbps";
- };
-
- lan3_amber {
- label = "amber:lan3";
- gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "dsa-0.0:01:1Gbps";
- };
-
- lan2_amber {
- label = "amber:lan2";
- gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "dsa-0.0:02:1Gbps";
- };
-
- lan1_amber {
- label = "amber:lan1";
- gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
- linux,default-trigger = "dsa-0.0:03:1Gbps";
- };
- };
-
- keys {
- compatible = "gpio-keys";
-
- reset {
- label = "reset";
- gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
- };
-
- reg_usb_vbus: regulator {
- compatible = "regulator-fixed";
- regulator-name = "usb_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio 12 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-};
-
-&xhci {
- vbus-supply = <®_usb_vbus>;
-};
-
-&nand {
- status = "okay";
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "Bootloader";
- reg = <0x0 0x40000>;
- read-only;
- };
-
- partition@40000 {
- label = "Config";
- reg = <0x40000 0x40000>;
- };
-
- partition@80000 {
- label = "Bdata";
- reg = <0x80000 0x40000>;
- read-only;
- };
-
- factory: partition@c0000 {
- label = "factory";
- reg = <0x0c0000 0x40000>;
- read-only;
- };
-
- partition@100000 {
- label = "crash";
- reg = <0x100000 0x40000>;
- };
-
- partition@140000 {
- label = "crash_syslog";
- reg = <0x140000 0x80000>;
- };
-
- partition@1c0000 {
- label = "reserved0";
- reg = <0x1c0000 0x40000>;
- read-only;
- };
-
- /* We keep stock xiaomi firmware (kernel0) here */
- partition@200000 {
- label = "kernel_stock";
- reg = <0x200000 0x400000>;
- };
-
- partition@600000 {
- label = "kernel";
- reg = <0x600000 0x400000>;
- };
-
- partition@a00000 {
- label = "ubi";
- reg = <0xa00000 0xf580000>;
- };
- };
-};
-
-&pcie {
- status = "okay";
-};
-
-&pcie0 {
- wifi@0,0 {
- compatible = "mediatek,mt76";
- reg = <0x0000 0 0 0 0>;
- mediatek,mtd-eeprom = <&factory 0x0000>;
- ieee80211-freq-limit = <2400000 2500000>;
- };
-};
-
-&pcie1 {
- wifi@0,0 {
- compatible = "mediatek,mt76";
- reg = <0x0000 0 0 0 0>;
- mediatek,mtd-eeprom = <&factory 0x8000>;
- ieee80211-freq-limit = <5000000 6000000>;
- };
-};
-
-&gmac0 {
- mtd-mac-address = <&factory 0xe006>;
-};
-
-&switch0 {
- ports {
- port@1 {
- status = "okay";
- label = "lan3";
- };
-
- port@2 {
- status = "okay";
- label = "lan2";
- };
-
- port@3 {
- status = "okay";
- label = "lan1";
- };
-
- port@4 {
- status = "okay";
- label = "wan";
- mtd-mac-address = <&factory 0xe000>;
- };
- };
-};
-
-&state_default {
- gpio {
- groups = "jtag", "uart2", "uart3", "wdt";
- function = "gpio";
- };
-};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7628an_xiaomi_mi-router-4.dtsi"
+
+/ {
+ compatible = "xiaomi,mi-router-4a-100m", "mediatek,mt7628an-soc";
+ model = "Xiaomi Mi Router 4A (100M Edition)";
+};
+
+&partitions {
+ partition@60000 {
+ label = "overlay";
+ reg = <0x60000 0x100000>;
+ read-only;
+ };
+
+ partition@160000 {
+ label = "firmware";
+ reg = <0x160000 0xea0000>;
+ compatible = "denx,uimage";
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi@0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ ieee80211-freq-limit = <5000000 6000000>;
+ };
+};
+
+ðernet {
+ mtd-mac-address = <&factory 0x4>;
+ mtd-mac-address-increment = <(-1)>;
+};
+
+&esw {
+ mediatek,portmap = <0x3e>;
+ mediatek,portdisable = <0x2a>;
+};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "mt7628an_xiaomi_mi-router-4.dtsi"
-
-/ {
- compatible = "xiaomi,mir4a-100m", "mediatek,mt7628an-soc";
- model = "Xiaomi Mi Router 4A (100M Edition)";
-};
-
-&partitions {
- partition@60000 {
- label = "overlay";
- reg = <0x60000 0x100000>;
- read-only;
- };
-
- partition@160000 {
- label = "firmware";
- reg = <0x160000 0xea0000>;
- compatible = "denx,uimage";
- };
-};
-
-&pcie {
- status = "okay";
-};
-
-&pcie0 {
- wifi@0,0 {
- compatible = "mediatek,mt76";
- reg = <0x0000 0 0 0 0>;
- mediatek,mtd-eeprom = <&factory 0x8000>;
- ieee80211-freq-limit = <5000000 6000000>;
- };
-};
-
-ðernet {
- mtd-mac-address = <&factory 0x4>;
- mtd-mac-address-increment = <(-1)>;
-};
-
-&esw {
- mediatek,portmap = <0x3e>;
- mediatek,portdisable = <0x2a>;
-};
uboot-envtools
endef
-define Device/xiaomi_mi-router-ac2100
- $(Device/xiaomi-ac2100)
- DEVICE_MODEL := Mi Router AC2100
-endef
-TARGET_DEVICES += xiaomi_mi-router-ac2100
-
-define Device/xiaomi_mir3g
+define Device/xiaomi_mi-router-3g
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
BLOCKSIZE := 128k
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router 3G
- SUPPORTED_DEVICES += R3G
- SUPPORTED_DEVICES += mir3g
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 \
kmod-usb-ledtrig-usbport uboot-envtools
+ SUPPORTED_DEVICES += R3G mir3g xiaomi,mir3g
endef
-TARGET_DEVICES += xiaomi_mir3g
+TARGET_DEVICES += xiaomi_mi-router-3g
-define Device/xiaomi_mir3g-v2
+define Device/xiaomi_mi-router-3g-v2
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
IMAGE_SIZE := 14848k
DEVICE_MODEL := Mi Router 3G
DEVICE_VARIANT := v2
DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2
+ SUPPORTED_DEVICES += xiaomi,mir3g-v2
endef
-TARGET_DEVICES += xiaomi_mir3g-v2
+TARGET_DEVICES += xiaomi_mi-router-3g-v2
-define Device/xiaomi_mir3p
+define Device/xiaomi_mi-router-3-pro
$(Device/dsa-migration)
$(Device/uimage-lzma-loader)
BLOCKSIZE := 128k
check-size
DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware kmod-usb3 \
kmod-usb-ledtrig-usbport uboot-envtools
+ SUPPORTED_DEVICES += xiaomi,mir3p
endef
-TARGET_DEVICES += xiaomi_mir3p
+TARGET_DEVICES += xiaomi_mi-router-3-pro
define Device/xiaomi_mi-router-4a-gigabit
$(Device/dsa-migration)
endef
TARGET_DEVICES += xiaomi_mi-router-4a-gigabit
+define Device/xiaomi_mi-router-ac2100
+ $(Device/xiaomi-ac2100)
+ DEVICE_MODEL := Mi Router AC2100
+endef
+TARGET_DEVICES += xiaomi_mi-router-ac2100
+
define Device/xiaomi_redmi-router-ac2100
$(Device/xiaomi-ac2100)
DEVICE_MODEL := Redmi Router AC2100
endef
TARGET_DEVICES += wrtnode_wrtnode2r
-define Device/xiaomi_mir4a-100m
+define Device/xiaomi_mi-router-4a-100m
IMAGE_SIZE := 14976k
DEVICE_VENDOR := Xiaomi
DEVICE_MODEL := Mi Router 4A
DEVICE_VARIANT := 100M Edition
DEVICE_PACKAGES := kmod-mt76x2
+ SUPPORTED_DEVICES += xiaomi,mir4a-100m
endef
-TARGET_DEVICES += xiaomi_mir4a-100m
+TARGET_DEVICES += xiaomi_mi-router-4a-100m
define Device/xiaomi_mi-router-4c
IMAGE_SIZE := 14976k
asiarf,ap7621-nv1|\
lenovo,newifi-d1|\
mikrotik,routerboard-m33g|\
- xiaomi,mir3g|\
- xiaomi,mir3g-v2|\
+ xiaomi,mi-router-3g|\
+ xiaomi,mi-router-3g-v2|\
xiaomi,mi-router-4a-gigabit)
ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
;;
;;
gehua,ghl-r-001|\
hiwifi,hc5962|\
+ xiaomi,mi-router-3-pro|\
xiaomi,mi-router-ac2100|\
- xiaomi,mir3p|\
xiaomi,redmi-router-ac2100)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan"
;;
netgear,wac104|\
netgear,wac124|\
netis,wf2881|\
+ xiaomi,mi-router-3g|\
+ xiaomi,mi-router-3-pro|\
xiaomi,mi-router-ac2100|\
- xiaomi,mir3g|\
- xiaomi,mir3p|\
xiaomi,redmi-router-ac2100)
nand_do_upgrade "$1"
;;
ucidef_add_switch "switch0" \
"0:wan" "3:lan" "4:lan" "6@eth0"
;;
- xiaomi,mir4a-100m)
+ xiaomi,mi-router-4a-100m)
ucidef_add_switch "switch0" \
"4:lan:1" "2:lan:2" "0:wan" "6@eth0"
;;
label_mac=$(mtd_get_mac_binary factory 0x4)
wan_mac=$(mtd_get_mac_binary factory 0x28)
;;
- xiaomi,mi-router-4c|\
- xiaomi,mir4a-100m)
+ xiaomi,mi-router-4a-100m|\
+ xiaomi,mi-router-4c)
wan_mac=$(mtd_get_mac_binary factory 0x4)
;;
esac
projects / openwrt / staging / robimarko.git / commitdiff