#include <asm/arch/emif_defs.h>
#include <asm/arch/pll_defs.h>
+#if defined(CONFIG_SYS_DA850_PLL_INIT)
void da850_waitloop(unsigned long loopcnt)
{
unsigned long i;
return 0;
}
+#endif /* CONFIG_SYS_DA850_PLL_INIT */
+#if defined(CONFIG_SYS_DA850_DDR_INIT)
int da850_ddr_setup(void)
{
unsigned long tmp;
return 0;
}
+#endif /* CONFIG_SYS_DA850_DDR_INIT */
__attribute__((weak))
void board_gpio_init(void)
return;
}
-/* pinmux_resource[] vector is defined in the board specific file */
-extern const struct pinmux_resource pinmuxes[];
-extern const int pinmuxes_size;
-
int arch_cpu_init(void)
{
/* Unlock kick registers */
if (davinci_configure_pin_mux_items(pinmuxes, pinmuxes_size))
return 1;
+#if defined(CONFIG_SYS_DA850_PLL_INIT)
/* PLL setup */
da850_pll_init(davinci_pllc0_regs, CONFIG_SYS_DA850_PLL0_PLLM);
da850_pll_init(davinci_pllc1_regs, CONFIG_SYS_DA850_PLL1_PLLM);
-
- /* GPIO setup */
- board_gpio_init();
-
+#endif
/* setup CSn config */
#if defined(CONFIG_SYS_DA850_CS2CFG)
writel(CONFIG_SYS_DA850_CS2CFG, &davinci_emif_regs->ab1cr);
writel(CONFIG_SYS_DA850_CS3CFG, &davinci_emif_regs->ab2cr);
#endif
- lpsc_on(CONFIG_SYS_DA850_LPSC_UART);
+ da8xx_configure_lpsc_items(lpsc, lpsc_size);
+
+ /* GPIO setup */
+ board_gpio_init();
+
+
NS16550_init((NS16550_t)(CONFIG_SYS_NS16550_COM1),
CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE);
DAVINCI_UART_PWREMU_MGMT_UTRST),
&davinci_uart2_ctrl_regs->pwremu_mgmt);
+#if defined(CONFIG_SYS_DA850_DDR_INIT)
da850_ddr_setup();
+#endif
+
return 0;
}
void board_init_r(gd_t *id, ulong dummy)
{
-#ifdef CONFIG_SOC_DM365
+#ifdef CONFIG_SPL_NAND_LOAD
nand_init();
puts("Nand boot...\n");
nand_boot();
#endif
-#ifdef CONFIG_SOC_DA8XX
+#ifdef CONFIG_SPL_SPI_LOAD
mem_malloc_init(CONFIG_SYS_TEXT_BASE - CONFIG_SYS_MALLOC_LEN,
CONFIG_SYS_MALLOC_LEN);
#ifndef __DA850_LOWLEVEL_H
#define __DA850_LOWLEVEL_H
+#include <asm/arch/pinmux_defs.h>
+
+/* pinmux_resource[] vector is defined in the board specific file */
+extern const struct pinmux_resource pinmuxes[];
+extern const int pinmuxes_size;
+
+extern const struct lpsc_resource lpsc[];
+extern const int lpsc_size;
+
/* NOR Boot Configuration Word Field Descriptions */
#define DA850_NORBOOT_COPY_XK(X) ((X - 1) << 8)
#define DA850_NORBOOT_METHOD_DIRECT (1 << 4)
const int pinmuxes_size = ARRAY_SIZE(pinmuxes);
-static const struct lpsc_resource lpsc[] = {
+const struct lpsc_resource lpsc[] = {
{ DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
{ DAVINCI_LPSC_SPI1 }, /* Serial Flash */
{ DAVINCI_LPSC_EMAC }, /* image download */
{ DAVINCI_LPSC_GPIO },
};
+const int lpsc_size = ARRAY_SIZE(lpsc);
+
#ifndef CONFIG_DA850_EVM_MAX_CPU_CLK
#define CONFIG_DA850_EVM_MAX_CPU_CLK 300000000
#endif
#include <asm/arch/hardware.h>
#include <asm/io.h>
#include <asm/arch/davinci_misc.h>
+#include <asm/arch/pinmux_defs.h>
#include <ns16550.h>
DECLARE_GLOBAL_DATA_PTR;
+const struct pinmux_resource pinmuxes[] = {
+ PINMUX_ITEM(emac_pins_mii),
+ PINMUX_ITEM(emac_pins_mdio),
+ PINMUX_ITEM(emifa_pins_cs3),
+ PINMUX_ITEM(emifa_pins_cs4),
+ PINMUX_ITEM(emifa_pins_nand),
+ PINMUX_ITEM(uart2_pins_txrx),
+ PINMUX_ITEM(uart2_pins_rtscts),
+};
+
+const int pinmuxes_size = ARRAY_SIZE(pinmuxes);
+
+const struct lpsc_resource lpsc[] = {
+ { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
+ { DAVINCI_LPSC_SPI1 }, /* Serial Flash */
+ { DAVINCI_LPSC_EMAC }, /* image download */
+ { DAVINCI_LPSC_UART2 }, /* console */
+ { DAVINCI_LPSC_GPIO },
+};
+
+const int lpsc_size = ARRAY_SIZE(lpsc);
+
int board_init(void)
{
/* arch number of the board */
+++ /dev/null
-/*
- * Modified for Hawkboard - Syed Mohammed Khasim <khasim@beagleboard.org>
- *
- * Copyright (C) 2008 Sekhar Nori, Texas Instruments, Inc. <nsekhar@ti.com>
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- * Copyright (C) 2004 Texas Instruments.
- *
- * ----------------------------------------------------------------------------
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- * ----------------------------------------------------------------------------
- */
-
-#include <common.h>
-#include <asm/errno.h>
-#include <asm/arch/hardware.h>
-#include <asm/io.h>
-#include <asm/arch/davinci_misc.h>
-#include <asm/arch/pinmux_defs.h>
-#include <ns16550.h>
-#include <nand.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static const struct pinmux_resource pinmuxes[] = {
- PINMUX_ITEM(emac_pins_mii),
- PINMUX_ITEM(emac_pins_mdio),
- PINMUX_ITEM(emifa_pins_cs3),
- PINMUX_ITEM(emifa_pins_cs4),
- PINMUX_ITEM(emifa_pins_nand),
- PINMUX_ITEM(uart2_pins_txrx),
- PINMUX_ITEM(uart2_pins_rtscts),
-};
-
-static const struct lpsc_resource lpsc[] = {
- { DAVINCI_LPSC_AEMIF }, /* NAND, NOR */
- { DAVINCI_LPSC_SPI1 }, /* Serial Flash */
- { DAVINCI_LPSC_EMAC }, /* image download */
- { DAVINCI_LPSC_UART2 }, /* console */
- { DAVINCI_LPSC_GPIO },
-};
-
-void board_init_f(ulong bootflag)
-{
- /*
- * Kick Registers need to be set to allow access to Pin Mux registers
- */
- writel(DV_SYSCFG_KICK0_UNLOCK, &davinci_syscfg_regs->kick0);
- writel(DV_SYSCFG_KICK1_UNLOCK, &davinci_syscfg_regs->kick1);
-
- /* setup the SUSPSRC for ARM to control emulation suspend */
- writel(readl(&davinci_syscfg_regs->suspsrc) &
- ~(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
- DAVINCI_SYSCFG_SUSPSRC_SPI1 | DAVINCI_SYSCFG_SUSPSRC_TIMER0 |
- DAVINCI_SYSCFG_SUSPSRC_UART2), &davinci_syscfg_regs->suspsrc);
-
- /* Power on required peripherals
- * ARM does not have acess by default to PSC0 and PSC1
- * assuming here that the DSP bootloader has set the IOPU
- * such that PSC access is available to ARM
- */
- da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc));
-
- /* configure pinmux settings */
- davinci_configure_pin_mux_items(pinmuxes,
- ARRAY_SIZE(pinmuxes));
-
- writel(readl(&davinci_uart2_ctrl_regs->pwremu_mgmt) |
- (DAVINCI_UART_PWREMU_MGMT_FREE) |
- (DAVINCI_UART_PWREMU_MGMT_URRST) |
- (DAVINCI_UART_PWREMU_MGMT_UTRST),
- &davinci_uart2_ctrl_regs->pwremu_mgmt);
-
- NS16550_init((NS16550_t)(DAVINCI_UART2_BASE),
- CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE);
-
- puts("Nand boot...\n");
-
- nand_boot();
-}
-
-void puts(const char *str)
-{
- while (*str)
- putc(*str++);
-}
-
-void putc(char c)
-{
- if (gd->flags & GD_FLG_SILENT)
- return;
-
- if (c == '\n')
- NS16550_putc((NS16550_t)(DAVINCI_UART2_BASE), '\r');
-
- NS16550_putc((NS16550_t)(DAVINCI_UART2_BASE), c);
-}
-
-void hang(void)
-{
- puts("### ERROR ### Please RESET the board ###\n");
- for (;;)
- ;
-}
--- /dev/null
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+ *
+ * (C) Copyright 2008
+ * Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+MEMORY { .sram : ORIGIN = CONFIG_SPL_TEXT_BASE,\
+ LENGTH = CONFIG_SPL_MAX_SIZE }
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0x00000000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ __start = .;
+ arch/arm/cpu/arm926ejs/start.o (.text)
+ *(.text*)
+ } >.sram
+
+ . = ALIGN(4);
+ .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram
+
+ . = ALIGN(4);
+ .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram
+ . = ALIGN(4);
+ .rel.dyn : {
+ __rel_dyn_start = .;
+ *(.rel*)
+ __rel_dyn_end = .;
+ } >.sram
+
+ .dynsym : {
+ __dynsym_start = .;
+ *(.dynsym)
+ } >.sram
+
+ .bss :
+ {
+ . = ALIGN(4);
+ __bss_start = .;
+ *(.bss*)
+ . = ALIGN(4);
+ __bss_end__ = .;
+ } >.sram
+
+ __image_copy_end = .;
+ _end = .;
+}
--- /dev/null
+/*
+ * (C) Copyright 2002
+ * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
+ *
+ * (C) Copyright 2008
+ * Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
+OUTPUT_ARCH(arm)
+ENTRY(_start)
+SECTIONS
+{
+ . = 0xc1080000;
+
+ . = ALIGN(4);
+ .text :
+ {
+ arch/arm/cpu/arm926ejs/start.o (.text)
+ arch/arm/cpu/arm926ejs/davinci/libdavinci.o (.text)
+ drivers/mtd/nand/libnand.o (.text)
+
+ *(.text*)
+ }
+
+ . = ALIGN(4);
+ .rodata : { *(.rodata) }
+
+ . = ALIGN(4);
+ .data : {
+ *(.data)
+ __datarel_start = .;
+ *(.data.rel)
+ __datarelrolocal_start = .;
+ *(.data.rel.ro.local)
+ __datarellocal_start = .;
+ *(.data.rel.local)
+ __datarelro_start = .;
+ *(.data.rel.ro)
+ }
+
+ . = ALIGN(4);
+ __rel_dyn_start = .;
+ __rel_dyn_end = .;
+ __dynsym_start = .;
+
+ __got_start = .;
+ . = ALIGN(4);
+ .got : { *(.got) }
+
+ __got_end = .;
+
+ .bss :
+ {
+ . = ALIGN(4);
+ __bss_start = .;
+ *(.bss*)
+ . = ALIGN(4);
+ __bss_end__ = .;
+ }
+
+ _end = .;
+}
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- *
- * (C) Copyright 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-MEMORY { .sram : ORIGIN = CONFIG_SPL_TEXT_BASE,\
- LENGTH = CONFIG_SPL_MAX_SIZE }
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(_start)
-SECTIONS
-{
- . = 0x00000000;
-
- . = ALIGN(4);
- .text :
- {
- __start = .;
- arch/arm/cpu/arm926ejs/start.o (.text)
- *(.text*)
- } >.sram
-
- . = ALIGN(4);
- .rodata : { *(SORT_BY_ALIGNMENT(.rodata*)) } >.sram
-
- . = ALIGN(4);
- .data : { *(SORT_BY_ALIGNMENT(.data*)) } >.sram
- . = ALIGN(4);
- .rel.dyn : {
- __rel_dyn_start = .;
- *(.rel*)
- __rel_dyn_end = .;
- } >.sram
-
- .dynsym : {
- __dynsym_start = .;
- *(.dynsym)
- } >.sram
-
- .bss :
- {
- . = ALIGN(4);
- __bss_start = .;
- *(.bss*)
- . = ALIGN(4);
- __bss_end__ = .;
- } >.sram
-
- __image_copy_end = .;
- _end = .;
-}
DECLARE_GLOBAL_DATA_PTR;
-static const struct lpsc_resource lpsc[] = {
+const struct lpsc_resource lpsc[] = {
{ DAVINCI_LPSC_AEMIF },
{ DAVINCI_LPSC_SPI1 },
{ DAVINCI_LPSC_ARM_RAM_ROM },
{ DAVINCI_LPSC_USB11 },
};
+const int lpsc_size = ARRAY_SIZE(lpsc);
+
static const struct pinmux_config enbw_pins[] = {
{ pinmux(0), 8, 0 },
{ pinmux(0), 8, 1 },
{
struct davinci_gpio *gpio = davinci_gpio_bank01;
- /*
- * Power on required peripherals
- * ARM does not have access by default to PSC0 and PSC1
- * assuming here that the DSP bootloader has set the IOPU
- * such that PSC access is available to ARM
- */
- if (da8xx_configure_lpsc_items(lpsc, ARRAY_SIZE(lpsc)))
- return;
-
/*
* set LED (gpio Interface not usable here)
* set LED pins to output and state 0
davinci_sonata arm arm926ejs sonata davinci davinci
ea20 arm arm926ejs ea20 davinci davinci
hawkboard arm arm926ejs da8xxevm davinci davinci
-hawkboard_nand arm arm926ejs da8xxevm davinci davinci hawkboard:NAND_U_BOOT
hawkboard_uart arm arm926ejs da8xxevm davinci davinci hawkboard:UART_U_BOOT
enbw_cmc arm arm926ejs enbw_cmc enbw davinci
dns325 arm arm926ejs - d-link kirkwood
internal ROM of the omap. The RBL initialises the memory and the nand
controller, and copies the image stored at a predefined location(block
1) of the nand flash. The image loaded by the RBL to the memory is the
-AIS signed nand_spl image. This, in turns copies the u-boot binary
-from the nand flash to the memory and jumps to the u-boot entry point.
+AIS signed spl image. This, in turns copies the u-boot binary from the
+nand flash to the memory and jumps to the u-boot entry point.
AIS is an image format defined by TI for the images that are to be
loaded to memory by the RBL. The image is divided into a series of
image. At the end of the image the RBL jumps to the image entry
point.
-The secondary stage bootloader(nand_spl) which is loaded by the RBL
-then loads the u-boot from a predefined location in the nand to the
-memory and jumps to the u-boot entry point.
+The secondary stage bootloader(spl) which is loaded by the RBL then
+loads the u-boot from a predefined location in the nand to the memory
+and jumps to the u-boot entry point.
The reason a secondary stage bootloader is used is because the ECC
layout expected by the RBL is not the same as that used by
-u-boot/linux. This also implies that for flashing the nand_spl image,
-we need to use the u-boot which uses the ECC layout expected by the
+u-boot/linux. This also implies that for flashing the spl image,we
+need to use the u-boot which uses the ECC layout expected by the
RBL[1]. Booting u-boot over UART(UART boot) is explained here[2].
===========
Three images might be needed
-* nand_spl - This is the secondary bootloader which boots the u-boot
+* spl - This is the secondary bootloader which boots the u-boot
binary.
- hawkboard_nand_config
-
- The nand_spl ELF gets generated under nand_spl/u-boot-spl. This
- needs to be processed with the AISGen tool for generating the AIS
- signed image to be flashed. Steps for generating the AIS image are
- explained here[3].
-
* u-boot binary - This is the image flashed to the nand and copied to
- the memory by the nand_spl.
+ the memory by the spl.
+
+ Both the images get compiled with hawkboard_config, with the TOPDIR
+ containing the u-boot images, and the spl image under the spl
+ directory.
- hawkboard_config
+ The spl image needs to be processed with the AISGen tool for
+ generating the AIS signed image to be flashed. Steps for generating
+ the AIS image are explained here[3].
* u-boot for uart boot - This is same as the u-boot binary generated
above, with the sole difference of the CONFIG_SYS_TEXT_BASE being
Flashing the images to Nand
===========================
-The nand_spl AIS image needs to be flashed to the block 1 of the
-Nand flash, as that is the location the RBL expects the image[4]. For
-flashing the nand_spl, boot over the u-boot specified in [1], and
-flash the image
+The spl AIS image needs to be flashed to the block 1 of the Nand
+flash, as that is the location the RBL expects the image[4]. For
+flashing the spl, boot over the u-boot specified in [1], and flash the
+image
=> tftpboot 0xc0700000 <nand_spl_ais.bin>
=> nand erase 0x20000 0x20000
=> nand write.e 0xc0700000 0x20000 <nand_spl_size>
The u-boot binary is flashed at location 0xe0000(block 6) of the nand
-flash. The nand_spl loader expects the u-boot at this location. For
+flash. The spl loader expects the u-boot at this location. For
flashing the u-boot binary
=> tftpboot 0xc0700000 u-boot.bin
#define CONFIG_SYS_HZ_CLOCK clk_get(DAVINCI_AUXCLK_CLKID)
#define CONFIG_SYS_HZ 1000
#define CONFIG_SYS_TEXT_BASE 0xc1080000
+#define CONFIG_SYS_DA850_PLL_INIT
+#define CONFIG_SYS_DA850_DDR_INIT
/*
* Memory Info
#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
#define CONFIG_BAUDRATE 115200 /* Default baud rate */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_SYS_DA850_LPSC_UART DAVINCI_LPSC_UART2
#define CONFIG_SPI
#define CONFIG_SPI_FLASH
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_LDSCRIPT "$(BOARDDIR)/u-boot-spl.lds"
+#define CONFIG_SPL_LDSCRIPT "board/$(BOARDDIR)/u-boot-spl-da850evm.lds"
#define CONFIG_SPL_STACK 0x8001ff00
#define CONFIG_SPL_TEXT_BASE 0x80000000
#define CONFIG_SPL_MAX_SIZE 32768
#define CONFIG_SYS_HZ 1000
#define CONFIG_DA850_LOWLEVEL
#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_SYS_DA850_PLL_INIT
+#define CONFIG_SYS_DA850_DDR_INIT
#define CONFIG_DA8XX_GPIO
#define CONFIG_HOSTNAME enbw_cmc
#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
#define CONFIG_BAUDRATE 115200 /* Default baud rate */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_SYS_DA850_LPSC_UART DAVINCI_LPSC_UART2
+
/*
* I2C Configuration
*/
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F
-#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_UART_U_BOOT)
+#define CONFIG_SYS_DA850_SYSCFG_SUSPSRC ( \
+ DAVINCI_SYSCFG_SUSPSRC_EMAC | \
+ DAVINCI_SYSCFG_SUSPSRC_I2C | \
+ DAVINCI_SYSCFG_SUSPSRC_SPI1 | \
+ DAVINCI_SYSCFG_SUSPSRC_TIMER0 | \
+ DAVINCI_SYSCFG_SUSPSRC_UART2)
+
+#if defined(CONFIG_UART_U_BOOT)
#define CONFIG_SYS_TEXT_BASE 0xc1080000
-#else
+#elif !defined(CONFIG_SPL_BUILD)
#define CONFIG_SYS_TEXT_BASE 0xc1180000
#endif
+/* Spl */
+#define CONFIG_SPL
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_NAND_LOAD
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_LDSCRIPT "board/$(BOARDDIR)/u-boot-spl-hawk.lds"
+#define CONFIG_SPL_TEXT_BASE 0xc1080000
+#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR
+
/*
* Memory Info
*/
/*
* Network & Ethernet Configuration
*/
-#if !defined(CONFIG_NAND_SPL)
#define CONFIG_DRIVER_TI_EMAC
-#endif
#define CONFIG_MII
#define CONFIG_BOOTP_DEFAULT
#define CONFIG_BOOTP_DNS
+++ /dev/null
-#
-# (C) Copyright 2006-2007
-# Stefan Roese, DENX Software Engineering, sr@denx.de.
-#
-# (C) Copyright 2008
-# Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de>
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-CONFIG_NAND_SPL = y
-
-include $(TOPDIR)/config.mk
-
-nandobj := $(OBJTREE)/nand_spl/
-
-LDSCRIPT= $(TOPDIR)/nand_spl/board/$(BOARDDIR)/u-boot.lds
-LDFLAGS := -T $(nandobj)u-boot.lds -Ttext $(CONFIG_SYS_TEXT_BASE) $(LDFLAGS) \
- $(LDFLAGS_FINAL)
-AFLAGS += -DCONFIG_SPL_BUILD -DCONFIG_NAND_SPL
-CFLAGS += -DCONFIG_SPL_BUILD -DCONFIG_NAND_SPL
-
-SOBJS = _divsi3.o \
- _udivsi3.o \
- start.o
-
-COBJS = cpu.o \
- davinci_nand.o \
- pinmux.o \
- da850_pinmux.o \
- div0.o \
- hawkboard_nand_spl.o \
- misc.o \
- nand_boot.o \
- ns16550.o \
- psc.o
-
-SRCS := $(addprefix $(obj),$(SOBJS:.o=.S) $(COBJS:.o=.c))
-OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
-__OBJS := $(SOBJS) $(COBJS)
-LNDIR := $(nandobj)board/$(BOARDDIR)
-
-ALL = $(nandobj)u-boot-spl $(nandobj)u-boot-spl.bin \
- $(nandobj)u-boot-spl-16k.bin
-
-all: $(ALL)
-
-$(nandobj)u-boot-spl-16k.bin: $(nandobj)u-boot-spl
- $(OBJCOPY) ${OBJCFLAGS} --pad-to=$(PAD_TO) -O binary $< $@
-
-$(nandobj)u-boot-spl.bin: $(nandobj)u-boot-spl
- $(OBJCOPY) ${OBJCFLAGS} -O binary $< $@
-
-$(nandobj)u-boot-spl: $(OBJS) $(nandobj)u-boot.lds
- cd $(LNDIR) && $(LD) $(LDFLAGS) $(__OBJS) \
- -Map $(nandobj)u-boot-spl.map \
- -o $(nandobj)u-boot-spl
-
-$(nandobj)u-boot.lds: $(LDSCRIPT)
- $(CPP) $(CPPFLAGS) $(LDPPFLAGS) -ansi -D__ASSEMBLY__ -P - <$^ >$@
-
-# create symbolic links for common files
-
-# from board directory
-$(obj)pinmux.c:
- @rm -f $@
- @ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/pinmux.c $@
-
-$(obj)da850_pinmux.c:
- @rm -f $@
- @ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c $@
-
-# from drivers/mtd/nand directory
-$(obj)davinci_nand.c:
- @rm -f $@
- @ln -s $(TOPDIR)/drivers/mtd/nand/davinci_nand.c $@
-
-# from nand_spl directory
-$(obj)nand_boot.c:
- @rm -f $@
- @ln -s $(TOPDIR)/nand_spl/nand_boot.c $@
-
-# from drivers/serial directory
-$(obj)ns16550.c:
- @rm -f $@
- @ln -sf $(TOPDIR)/drivers/serial/ns16550.c $@
-
-# from cpu directory
-$(obj)start.S:
- @rm -f $@
- ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/start.S $@
-
-# from lib directory
-$(obj)_udivsi3.S:
- @rm -f $@
- ln -s $(TOPDIR)/arch/arm/lib/_udivsi3.S $@
-
-# from lib directory
-$(obj)_divsi3.S:
- @rm -f $@
- ln -s $(TOPDIR)/arch/arm/lib/_divsi3.S $@
-
-# from lib directory
-$(obj)div0.c:
- @rm -f $@
- ln -s $(TOPDIR)/arch/arm/lib/div0.c $@
-
-# from SoC directory
-$(obj)cpu.c:
- @rm -f $@
- @ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/cpu.c $@
-
-$(obj)misc.c:
- @rm -f $@
- ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/misc.c $@
-
-# from board directory
-$(obj)hawkboard_nand_spl.c:
- @rm -f $@
- ln -s $(TOPDIR)/board/davinci/da8xxevm/hawkboard_nand_spl.c $@
-
-$(obj)psc.c:
- @rm -f $@
- ln -s $(TOPDIR)/arch/arm/cpu/arm926ejs/davinci/psc.c $@
-
-#########################################################################
-
-$(obj)%.o: $(obj)%.S
- $(CC) $(AFLAGS) -c -o $@ $<
-
-$(obj)%.o: $(obj)%.c
- $(CC) $(CFLAGS) -c -o $@ $<
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-/*
- * (C) Copyright 2002
- * Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
- *
- * (C) Copyright 2008
- * Guennadi Liakhovetki, DENX Software Engineering, <lg@denx.de>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm")
-OUTPUT_ARCH(arm)
-ENTRY(_start)
-SECTIONS
-{
- . = 0xc1080000;
-
- . = ALIGN(4);
- .text :
- {
- start.o (.text)
- cpu.o (.text)
- nand_boot.o (.text)
-
- *(.text)
- }
-
- . = ALIGN(4);
- .rodata : { *(.rodata) }
-
- . = ALIGN(4);
- .data : {
- *(.data)
- __datarel_start = .;
- *(.data.rel)
- __datarelrolocal_start = .;
- *(.data.rel.ro.local)
- __datarellocal_start = .;
- *(.data.rel.local)
- __datarelro_start = .;
- *(.data.rel.ro)
- }
-
- . = ALIGN(4);
- __rel_dyn_start = .;
- __rel_dyn_end = .;
- __dynsym_start = .;
-
- __got_start = .;
- . = ALIGN(4);
- .got : { *(.got) }
-
- __got_end = .;
-
- _end = .;
-
- . = ALIGN(4);
- __bss_start = .;
- .bss : { *(.bss) }
- __bss_end__ = .;
-}
projects / project / bcm63xx / u-boot.git / commitdiff