OrayBox X3A is a 2.4/5GHz dual band AC router, based on MediaTek MT7621.
Specification:
* SoC: MT7621
* RAM: DDR3 128 MiB
* Flash: 16 MiB NOR (XM25Q128)
* Wi-Fi: (single chip hosting both 2.4G and 5G)
* 2.4GHz: MT7615
* 5GHz: MT7615
* Ethernet: 3x 1000Mbps
* Switch: MT7530
* LED:
* Ethernet LEDs: On the back of the router, hardware-controlled.
* Status LEDs: One "pixel-like" RGB LED in the front of the router,
which is actually made up of 3 individual LEDs (with
dedicated GPIO pins) with the color of Red, Green,
and Blue.
The OEM firmware only lights up one color at a time to
indicate status, but that's very boring, and the colors
actually look great when combined, so I've improvised a
little and made them indicate netdev activities.
My test results:
GPIO 13/14/15
000 white (actually more like bright green or cyan
because the brightness of the green LED is
higher than red and blue)
001 bright purple
010 bright green
011 red
100 bright cyan
101 blue
110 green
111 off
Flash Layout:
0x0000000-0x0030000 : "u-boot"
0x0030000-0x0040000 : "u-boot-env"
0x0040000-0x0050000 : "factory"
0x0050000-0x0f50000 : "firmware"
/*0x0f50000 to 0x0fe0000 is undefined, same as OEM firmware*/
0x0fe0000-0x0ff0000 : "bdinfo"
0x0ff0000-0x1000000 : "reserve"
MAC address:
MAC Source Description Fix
A0:CX:XX:BX:XX:0D BDINFO_9 LAN(LABEL) DTS
A0:CX:XX:BX:XX:0E BDINFO_9 + 1 WAN DTS
A2:CX:XX:BX:XX:0F FACTORY_4 WIFI2G DTS
A2:CX:XX:CX:XX:0F SETBIT 7 (FACTORY_4 + 0x100000) WIFI5G HOTPLUG
A6:CX:XX:BX:XX:0F N/A WIFI2G_CLIENT N/A
A6:DX:XX:BX:XX:0F N/A WIFI5G_CLIENT N/A
Stock dmesg:
https://pastebin.com/2t2jwLdf
Stock Dumps:
https://pastebin.com/LDLxSWX3
Installation via SSH (does not void your warranty):
1. -----UNLOCK SSH-----
1.1 Set computer IP to DHCP mode, load 'http://10.168.1.1/cgi-bin/luci' in
your browser. Password is 'admin'.
1.2 Click the "备份且导出" (backup and export) button, and download the
config file.
1.3 Open the downloaded file with 7zip, navigate to '/etc/config/'.
1.4 Edit the file './system'. Change the '0' into '1' under
"config sys 'ssh'".
1.5 Save the file.
1.6 Upload the file by clicking the "导入且恢复" (import and recover)
button. The router will automatically reboot.
2. -----FLASH THE OPENWRT FIRMWARE-----
2.1 Use any scp tool to upload the 'sysupgrade' firmware to the '/tmp/'
folder to your router. It should be root@10.168.1.1 and the password
is 'admin'.
2.2 SSH into the router, also root@10.168.1.1 and the password is 'admin'.
2.3 **IMPORTANT** Type command 'dd if=/dev/mtd3 of=/tmp/firmware.bin', to
backup the stock firmware. Since the OEM does not provide firmware
download on their website, this is the only way to get it.
2.3 **ALSO IMPORTANT** Use any scp tool to download your backed-up stock
firmware from '/tmp/' to your local drive. Then you'd better use a hex
reading tool to have a rough look at it to make sure nothing is
corrupt. Or u can just back up again and cross check the MD5.
2.4 Type command 'mtd write /tmp/XXX.bin firmware', and it should flash
the firmware.
2.5 Verify that nothing went wrong. If you're confident, type 'reboot' and
reboot the router.
Revert to stock firmware:
1. load stock firmware using mtd (make sure u have a backup).
Signed-off-by: Ray Wang <raywang777@foxmail.com>
(cherry picked from commit
9a750aae62de74b488d7df7bdbfa78cd606a8aaf)
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "oraybox,x3a", "mediatek,mt7621-soc";
+ model = "OrayBox X3A";
+
+ aliases {
+ led-boot = &led_status_green;
+ led-failsafe = &led_status_red;
+ led-running = &led_status_blue;
+ led-upgrade = &led_status_green;
+ label-mac-device = &gmac0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_red: status-red {
+ label = "red:status";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_blue: status-blue {
+ label = "blue:status";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_green: status-green {
+ label = "green:status";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <30000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition@40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition@50000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x50000 0xf00000>;
+ };
+
+ partition@fe0000 {
+ label = "bdinfo";
+ reg = <0xfe0000 0x10000>;
+ read-only;
+
+ compatible = "nvmem-cells";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_bdinfo_9: macaddr@9 {
+ reg = <0x9 0x6>;
+ };
+ };
+
+ partition@ff0000 {
+ label = "reserve";
+ reg = <0xff0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pcie0 {
+ wifi@0,0 {
+ compatible = "mediatek,mt76";
+ reg = <0x0000 0 0 0 0>;
+ mediatek,mtd-eeprom = <&factory 0x0>;
+ };
+};
+
+&gmac0 {
+ nvmem-cells = <&macaddr_bdinfo_9>;
+ nvmem-cell-names = "mac-address";
+};
+
+&switch0 {
+ ports {
+ port@2 {
+ status = "okay";
+ label = "lan2";
+ };
+
+ port@3 {
+ status = "okay";
+ label = "lan1";
+ };
+
+ port@4 {
+ status = "okay";
+ label = "wan";
+ nvmem-cells = <&macaddr_bdinfo_9>;
+ nvmem-cell-names = "mac-address";
+ mac-address-increment = <1>;
+ };
+ };
+};
+
+&state_default {
+ gpio {
+ groups = "jtag", "wdt";
+ function = "gpio";
+ };
+};
endef
TARGET_DEVICES += netis_wf2881
+define Device/oraybox_x3a
+ $(Device/dsa-migration)
+ $(Device/uimage-lzma-loader)
+ IMAGE_SIZE := 15360k
+ DEVICE_VENDOR := OrayBox
+ DEVICE_MODEL := X3A
+ DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware
+endef
+TARGET_DEVICES += oraybox_x3a
+
define Device/phicomm_k2p
$(Device/dsa-migration)
IMAGE_SIZE := 15744k
ucidef_set_led_netdev "lan3" "LAN3" "white:lan3" "lan3"
ucidef_set_led_netdev "lan4" "LAN4" "white:lan4" "lan4"
;;
+oraybox,x3a)
+ ucidef_set_led_netdev "wan" "wan link" "red:status" "wan"
+ ucidef_set_led_netdev "lan" "lan link" "green:status" "br-lan"
+ ;;
tplink,archer-a6-v3|\
tplink,archer-c6-v3|\
tplink,archer-c6u-v1)
jcg,q20|\
lenovo,newifi-d1|\
mikrotik,routerboard-m33g|\
+ oraybox,x3a|\
renkforce,ws-wn530hp3-a|\
xiaomi,mi-router-3g|\
xiaomi,mi-router-3g-v2|\
[ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 1 > /sys${DEVPATH}/macaddress
[ "$PHYNBR" = "1" ] && macaddr_add $hw_mac_addr 2 > /sys${DEVPATH}/macaddress
;;
+ oraybox,x3a)
+ if [ "$PHYNBR" = "1" ]; then
+ hw_mac_addr="$(mtd_get_mac_binary factory 0x4)"
+ macaddr_setbit_la "$(macaddr_add $hw_mac_addr 0x100000)" > /sys${DEVPATH}/macaddress
+ fi
+ ;;
raisecom,msg1500-x-00)
[ "$PHYNBR" = "0" ] && \
macaddr_setbit_la "$(mtd_get_mac_ascii Config protest_lan_mac)" \
projects / openwrt / staging / hauke.git / commitdiff