ramips: Add support for D-Link DIR-3060 A1

Hardware specification:
SoC: MediaTek MT7621AT
Flash: Winbond W29N01HVSINA 128MB
RAM: Micron MT41K128M16JT-125 256MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7615DN 2.4GHz N 2x2:2
WiFi2: MT7615DN 5GHz AC 2x2:2
WiFi3: MT7615N 5GHz AC 4x4:4
Button: WPS, Reset

Flash instructions:
OpenWrt can be installed via D-Link Recovery GUI:

    Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
    Give it ~30 seconds, to boot the recovery mode GUI
    Connect your client computer to LAN1 of the device
    Set your client IP address manually to 192.168.0.2 / 255.255.255.0.
    Call the recovery page for the device at http://192.168.0.1/
    Use the provided emergency web GUI to upload and flash a new firmware to the device

Signed-off-by: Ivaylo Ivanov <iivailo@mail.bg>

diff --git a/target/linux/ramips/dts/mt7621_dlink_dir-3060-a1.dts b/target/linux/ramips/dts/mt7621_dlink_dir-3060-a1.dts
new file mode 100644 (file)
index 0000000..675a3aa
--- /dev/null
+++ b/target/linux/ramips/dts/mt7621_dlink_dir-3060-a1.dts
@@ -0,0 +1,241 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "mt7621.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+       compatible = "dlink,dir-3060-a1", "mediatek,mt7621-soc";
+       model = "D-Link DIR-3060 A1";
+
+       aliases {
+               label-mac-device = &gmac0;
+               led-boot = &led_power_orange;
+               led-failsafe = &led_power_white;
+               led-running = &led_power_white;
+               led-upgrade = &led_net_orange;
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_RESTART>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led_power_orange: power_orange {
+                       label = "orange:power";
+                       gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+               };
+
+               led_power_white: power_white {
+                       label = "white:power";
+                       gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+               };
+
+               led_net_orange: net_orange {
+                       label = "orange:net";
+                       gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
+               };
+
+               net_white {
+                       label = "white:net";
+                       gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+               };
+               
+               usb2_white {
+                       label = "white:usb2";
+                       gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+                       trigger-sources = <&ehci_port2>;
+                       linux,default-trigger = "usbport";
+               };
+
+               usb3_white {
+                       label = "white:usb3";
+                       gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+                       trigger-sources = <&xhci_ehci_port1>;
+                       linux,default-trigger = "usbport";
+               };
+
+               wlan2g {
+                       label = "white:wlan2g";
+                       gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
+                       linux,default-trigger = "phy0radio";
+               };
+
+               wlan5glb {
+                       label = "white:wlan5glb";
+                       gpios = <&gpio 9 GPIO_ACTIVE_HIGH>;
+                       linux,default-trigger = "phy1radio";
+               };
+
+               wlan5ghb {
+                       label = "white:wlan5ghb";
+                       gpios = <&gpio 5 GPIO_ACTIVE_HIGH>;
+                       linux,default-trigger = "phy2radio";
+               };
+       };
+};
+
+&nand {
+       status = "okay";
+
+       partitions {
+               compatible = "fixed-partitions";
+               #address-cells = <1>;
+               #size-cells = <1>;
+
+               partition@0 {
+                       label = "Bootloader";
+                       reg = <0x0 0x80000>;
+                       read-only;
+               };
+
+               partition@80000 {
+                       label = "config";
+                       reg = <0x80000 0x80000>;
+                       read-only;
+               };
+
+               factory: partition@100000 {
+                       label = "factory";
+                       reg = <0x100000 0x40000>;
+                       read-only;
+               };
+
+               partition@140000 {
+                       label = "config2";
+                       reg = <0x140000 0x40000>;
+                       read-only;
+               };
+
+               partition@180000 {
+                       label = "firmware";
+                       compatible = "openwrt,uimage", "denx,uimage";
+                       openwrt,padding = <96>;
+                       reg = <0x180000 0x2800000>;
+               };
+
+               partition@2980000 {
+                       label = "private";
+                       reg = <0x2980000 0x2000000>;
+                       read-only;
+               };
+
+               partition@4980000 {
+                       label = "firmware2";
+                       reg = <0x4980000 0x2800000>;
+                       read-only;
+               };
+
+               partition@7180000 {
+                       label = "mydlink";
+                       reg = <0x7180000 0x600000>;
+                       read-only;
+               };
+
+               partition@7780000 {
+                       label = "reserved";
+                       reg = <0x7780000 0x880000>;
+                       read-only;
+               };
+       };
+};
+
+&pcie {
+       status = "okay";
+};
+
+&pcie0 {
+       wifi0: wifi@0,0 {
+               compatible = "mediatek,mt76";
+               reg = <0x0000 0 0 0 0>;
+               mediatek,mtd-eeprom = <&factory 0x0>;
+               ieee80211-freq-limit = <2400000 6000000>;
+               nvmem-cells = <&macaddr_factory_e000>;
+               nvmem-cell-names = "mac-address";
+               mac-address-increment = <1>;
+       };
+};
+
+&pcie1 {
+       wifi1: wifi@0,0 {
+               compatible = "mediatek,mt76";
+               reg = <0x0000 0 0 0 0>;
+               mediatek,mtd-eeprom = <&factory 0x8000>;
+               ieee80211-freq-limit = <5000000 6000000>;
+               nvmem-cells = <&macaddr_factory_e000>;
+               nvmem-cell-names = "mac-address";
+               mac-address-increment = <3>;
+       };
+};
+
+&gmac0 {
+       nvmem-cells = <&macaddr_factory_e000>;
+       nvmem-cell-names = "mac-address";
+};
+
+&switch0 {
+       ports {
+               port@0 {
+                       status = "okay";
+                       label = "lan4";
+               };
+
+               port@1 {
+                       status = "okay";
+                       label = "lan3";
+               };
+
+               port@2 {
+                       status = "okay";
+                       label = "lan2";
+               };
+
+               port@3 {
+                       status = "okay";
+                       label = "lan1";
+               };
+
+               port@4 {
+                       status = "okay";
+                       label = "wan";
+                       nvmem-cells = <&macaddr_factory_e006>;
+                       nvmem-cell-names = "mac-address";
+               };
+       };
+};
+
+&state_default {
+       gpio {
+               groups = "i2c", "uart3", "jtag", "wdt";
+               function = "gpio";
+       };
+};
+
+&factory {
+       compatible = "nvmem-cells";
+       #address-cells = <1>;
+       #size-cells = <1>;
+
+       macaddr_factory_e000: macaddr@e000 {
+               reg = <0xe000 0x6>;
+       };
+
+       macaddr_factory_e006: macaddr@e006 {
+               reg = <0xe006 0x6>;
+       };
+};

diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
index e7b38aaacf080b06340e12cb9f62a5c08dba4278..81ee50e0af82345e7936915ccaf0d2f53b944b73 100644 (file)
--- a/target/linux/ramips/image/mt7621.mk
+++ b/target/linux/ramips/image/mt7621.mk
@@ -547,6 +547,13 @@ define Device/dlink_dir-2660-a1
 endef
 TARGET_DEVICES += dlink_dir-2660-a1
 
+define Device/dlink_dir-3060-a1
+  $(Device/dlink_dir-xx60-a1)
+  DEVICE_MODEL := DIR-3060
+  DEVICE_VARIANT := A1
+endef
+TARGET_DEVICES += dlink_dir-3060-a1
+
 define Device/dlink_dir-853-a3
   $(Device/dlink_dir-xx60-a1)
   DEVICE_MODEL := DIR-853

diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
index 98db9fb9fc77f90d1430868614f46f3cbcca3434..9bac8228a0aabbe6ebeb883e34a026d8291f45b7 100644 (file)
--- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
@@ -55,6 +55,10 @@ dlink,dir-2640-a1|\
 dlink,dir-2660-a1)
        ucidef_set_led_netdev "wan" "wan" "white:net" "wan"
        ;;
+dlink,dir-3060-a1)
+       ucidef_set_led_netdev "net_white" "WAN Link" "white:net" "wan" "link"
+       ucidef_set_led_netdev "net_orange" "WAN Activity" "orange:net" "wan" "tx rx"
+       ;;
 dlink,dir-853-a3)
        ucidef_set_led_netdev "wan" "wan" "blue:net" "wan"
        ;;

diff --git a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
index 95bba16194ce34ed147c7aa9d1fbc0429d455ff8..06a35077dc157f1f45763ab0b7ec7f91aad977d7 100755 (executable)
--- a/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
@@ -62,6 +62,7 @@ platform_do_upgrade() {
        dlink,dir-1960-a1|\
        dlink,dir-2640-a1|\
        dlink,dir-2660-a1|\
+       dlink,dir-3060-a1|\
        dlink,dir-853-a3|\
        h3c,tx1800-plus|\
        h3c,tx1801-plus|\