;;
db120)
- ucidef_set_interfaces_lan_wan "eth1" "eth0"
- ucidef_add_switch "switch0" "1" "1"
- ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 4"
+ ucidef_set_interfaces_lan_wan "eth0.1 eth1" "eth0.2"
+ ucidef_add_switch "eth0" "1" "1"
+ ucidef_add_switch_vlan "eth0" "1" "0t 2 3 4 5"
+ ucidef_add_switch_vlan "eth0" "2" "0t 1"
+ ucidef_add_switch "eth1" "1" "1"
+ ucidef_add_switch_vlan "eth1" "1" "0 1 2 3 4 5"
;;
dir-825-b1|\
--- a/arch/mips/ath79/mach-db120.c
+++ b/arch/mips/ath79/mach-db120.c
-@@ -37,17 +37,26 @@
+@@ -2,7 +2,7 @@
+ * Atheros DB120 reference board support
+ *
+ * Copyright (c) 2011 Qualcomm Atheros
+- * Copyright (c) 2011 Gabor Juhos <juhosg@openwrt.org>
++ * Copyright (c) 2011-2012 Gabor Juhos <juhosg@openwrt.org>
+ *
+ * All rights reserved.
+ *
+@@ -37,17 +37,28 @@
* IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
#include <linux/pci.h>
++#include <linux/phy.h>
+#include <linux/platform_device.h>
#include <linux/ath9k_platform.h>
++#include <linux/ar8216_platform.h>
-#include "machtypes.h"
+#include <asm/mach-ath79/ar71xx_regs.h>
#define DB120_GPIO_LED_WLAN_5G 12
#define DB120_GPIO_LED_WLAN_2G 13
#define DB120_GPIO_LED_STATUS 14
-@@ -58,8 +67,50 @@
+@@ -58,8 +69,50 @@
#define DB120_KEYS_POLL_INTERVAL 20 /* msecs */
#define DB120_KEYS_DEBOUNCE_INTERVAL (3 * DB120_KEYS_POLL_INTERVAL)
static struct gpio_led db120_leds_gpio[] __initdata = {
{
-@@ -82,6 +133,11 @@ static struct gpio_led db120_leds_gpio[]
+@@ -82,6 +135,11 @@ static struct gpio_led db120_leds_gpio[]
.gpio = DB120_GPIO_LED_WLAN_2G,
.active_low = 1,
},
};
static struct gpio_keys_button db120_gpio_keys[] __initdata = {
-@@ -95,66 +151,65 @@ static struct gpio_keys_button db120_gpi
+@@ -95,66 +153,89 @@ static struct gpio_keys_button db120_gpi
},
};
-static struct ath79_spi_controller_data db120_spi0_data = {
- .cs_type = ATH79_SPI_CS_TYPE_INTERNAL,
- .cs_line = 0,
--};
--
++static struct ar8327_pad_cfg db120_ar8327_pad0_cfg = {
++ .mode = AR8327_PAD_MAC_RGMII,
++ .txclk_delay_en = true,
++ .rxclk_delay_en = true,
++ .txclk_delay_sel = AR8327_CLK_DELAY_SEL1,
++ .rxclk_delay_sel = AR8327_CLK_DELAY_SEL2,
+ };
+
-static struct spi_board_info db120_spi_info[] = {
- {
- .bus_num = 0,
- .max_speed_hz = 25000000,
- .modalias = "s25sl064a",
- .controller_data = &db120_spi0_data,
-- }
--};
--
++static struct ar8327_platform_data db120_ar8327_data = {
++ .pad0_cfg = &db120_ar8327_pad0_cfg,
++ .cpuport_cfg = {
++ .force_link = 1,
++ .speed = AR8327_PORT_SPEED_1000,
++ .duplex = 1,
++ .txpause = 1,
++ .rxpause = 1,
+ }
+ };
+
-static struct ath79_spi_platform_data db120_spi_data = {
- .bus_num = 0,
- .num_chipselect = 1,
--};
--
++static struct mdio_board_info db120_mdio0_info[] = {
++ {
++ .bus_id = "ag71xx-mdio.0",
++ .phy_addr = 0,
++ .platform_data = &db120_ar8327_data,
++ },
+ };
+
-#ifdef CONFIG_PCI
-static struct ath9k_platform_data db120_ath9k_data;
-
+ t = __raw_readl(base + AR934X_GMAC_REG_ETH_CFG);
+ t &= ~(AR934X_ETH_CFG_RGMII_GMAC0 | AR934X_ETH_CFG_MII_GMAC0 |
+ AR934X_ETH_CFG_MII_GMAC0 | AR934X_ETH_CFG_SW_ONLY_MODE);
++ t |= AR934X_ETH_CFG_RGMII_GMAC0 | AR934X_ETH_CFG_SW_ONLY_MODE;
++
+ __raw_writel(t, base + AR934X_GMAC_REG_ETH_CFG);
- ath79_pci_set_plat_dev_init(db120_pci_plat_dev_init);
+
+ db120_gmac_setup();
+
-+ ath79_register_mdio(0, 0x0);
+ ath79_register_mdio(1, 0x0);
++ ath79_register_mdio(0, 0x0);
+
+ ath79_init_mac(ath79_eth0_data.mac_addr, art + DB120_MAC0_OFFSET, 0);
-+#if 0
++
++ mdiobus_register_board_info(db120_mdio0_info,
++ ARRAY_SIZE(db120_mdio0_info));
++
+ /* GMAC0 is connected to an AR8327 switch */
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
-+ ath79_eth0_data.speed = SPEED_1000;
-+ ath79_eth0_data.duplex = DUPLEX_FULL;
-+#else
-+ /* GMAC0 is connected to PHY4 of the internal switch */
-+ ath79_switch_data.phy4_mii_en = 1;
-+
-+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
-+ ath79_eth0_data.phy_mask = BIT(4);
-+ ath79_eth0_data.mii_bus_dev = &ath79_mdio1_device.dev;
-+#endif
++ ath79_eth0_data.phy_mask = BIT(0);
++ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+ ath79_register_eth(0);
+
+ /* GMAC1 is connected to the internal switch */
--- a/arch/mips/ath79/mach-db120.c
+++ b/arch/mips/ath79/mach-db120.c
-@@ -37,17 +37,26 @@
+@@ -2,7 +2,7 @@
+ * Atheros DB120 reference board support
+ *
+ * Copyright (c) 2011 Qualcomm Atheros
+- * Copyright (c) 2011 Gabor Juhos <juhosg@openwrt.org>
++ * Copyright (c) 2011-2012 Gabor Juhos <juhosg@openwrt.org>
+ *
+ * All rights reserved.
+ *
+@@ -37,17 +37,28 @@
* IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
#include <linux/pci.h>
++#include <linux/phy.h>
+#include <linux/platform_device.h>
#include <linux/ath9k_platform.h>
++#include <linux/ar8216_platform.h>
-#include "machtypes.h"
+#include <asm/mach-ath79/ar71xx_regs.h>
#define DB120_GPIO_LED_WLAN_5G 12
#define DB120_GPIO_LED_WLAN_2G 13
#define DB120_GPIO_LED_STATUS 14
-@@ -58,8 +67,50 @@
+@@ -58,8 +69,50 @@
#define DB120_KEYS_POLL_INTERVAL 20 /* msecs */
#define DB120_KEYS_DEBOUNCE_INTERVAL (3 * DB120_KEYS_POLL_INTERVAL)
static struct gpio_led db120_leds_gpio[] __initdata = {
{
-@@ -82,6 +133,11 @@ static struct gpio_led db120_leds_gpio[]
+@@ -82,6 +135,11 @@ static struct gpio_led db120_leds_gpio[]
.gpio = DB120_GPIO_LED_WLAN_2G,
.active_low = 1,
},
};
static struct gpio_keys_button db120_gpio_keys[] __initdata = {
-@@ -95,66 +151,65 @@ static struct gpio_keys_button db120_gpi
+@@ -95,66 +153,89 @@ static struct gpio_keys_button db120_gpi
},
};
-static struct ath79_spi_controller_data db120_spi0_data = {
- .cs_type = ATH79_SPI_CS_TYPE_INTERNAL,
- .cs_line = 0,
--};
--
++static struct ar8327_pad_cfg db120_ar8327_pad0_cfg = {
++ .mode = AR8327_PAD_MAC_RGMII,
++ .txclk_delay_en = true,
++ .rxclk_delay_en = true,
++ .txclk_delay_sel = AR8327_CLK_DELAY_SEL1,
++ .rxclk_delay_sel = AR8327_CLK_DELAY_SEL2,
+ };
+
-static struct spi_board_info db120_spi_info[] = {
- {
- .bus_num = 0,
- .max_speed_hz = 25000000,
- .modalias = "s25sl064a",
- .controller_data = &db120_spi0_data,
-- }
--};
--
++static struct ar8327_platform_data db120_ar8327_data = {
++ .pad0_cfg = &db120_ar8327_pad0_cfg,
++ .cpuport_cfg = {
++ .force_link = 1,
++ .speed = AR8327_PORT_SPEED_1000,
++ .duplex = 1,
++ .txpause = 1,
++ .rxpause = 1,
+ }
+ };
+
-static struct ath79_spi_platform_data db120_spi_data = {
- .bus_num = 0,
- .num_chipselect = 1,
--};
--
++static struct mdio_board_info db120_mdio0_info[] = {
++ {
++ .bus_id = "ag71xx-mdio.0",
++ .phy_addr = 0,
++ .platform_data = &db120_ar8327_data,
++ },
+ };
+
-#ifdef CONFIG_PCI
-static struct ath9k_platform_data db120_ath9k_data;
-
+ t = __raw_readl(base + AR934X_GMAC_REG_ETH_CFG);
+ t &= ~(AR934X_ETH_CFG_RGMII_GMAC0 | AR934X_ETH_CFG_MII_GMAC0 |
+ AR934X_ETH_CFG_MII_GMAC0 | AR934X_ETH_CFG_SW_ONLY_MODE);
++ t |= AR934X_ETH_CFG_RGMII_GMAC0 | AR934X_ETH_CFG_SW_ONLY_MODE;
++
+ __raw_writel(t, base + AR934X_GMAC_REG_ETH_CFG);
- ath79_pci_set_plat_dev_init(db120_pci_plat_dev_init);
+
+ db120_gmac_setup();
+
-+ ath79_register_mdio(0, 0x0);
+ ath79_register_mdio(1, 0x0);
++ ath79_register_mdio(0, 0x0);
+
+ ath79_init_mac(ath79_eth0_data.mac_addr, art + DB120_MAC0_OFFSET, 0);
-+#if 0
++
++ mdiobus_register_board_info(db120_mdio0_info,
++ ARRAY_SIZE(db120_mdio0_info));
++
+ /* GMAC0 is connected to an AR8327 switch */
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
-+ ath79_eth0_data.speed = SPEED_1000;
-+ ath79_eth0_data.duplex = DUPLEX_FULL;
-+#else
-+ /* GMAC0 is connected to PHY4 of the internal switch */
-+ ath79_switch_data.phy4_mii_en = 1;
-+
-+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII;
-+ ath79_eth0_data.phy_mask = BIT(4);
-+ ath79_eth0_data.mii_bus_dev = &ath79_mdio1_device.dev;
-+#endif
++ ath79_eth0_data.phy_mask = BIT(0);
++ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+ ath79_register_eth(0);
+
+ /* GMAC1 is connected to the internal switch */
projects / openwrt / staging / stintel.git / commitdiff