This patch adds support for Cisco's Z1.
Detailed instructions for the flashing the device can
be found in the OpenWrt wiki:
<https://wiki.openwrt.org/toh/meraki/z1>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
ucidef_set_led_usbdev "usb" "USB" "buffalo:blue:usb" "1-1"
;;
+z1)
+ ucidef_set_led_netdev "wlan1" "WLAN1" "z1:blue:tricolor0" "wlan1"
+ ;;
+
zbt-we1526)
ucidef_set_led_netdev "wan" "WAN" "zbt-we1526:green:wan" "eth1"
ucidef_set_led_switch "lan1" "LAN1" "zbt-we1526:green:lan1" "switch0" "0x10"
ucidef_add_switch_port_attr "switch0" 5 led 2
;;
+z1)
+ ucidef_set_interfaces_lan_wan "eth0" "eth1"
+ ucidef_add_switch "switch0" \
+ "0@eth0" "1:lan:1" "2:lan:2" "3:lan:3" "4:lan:4" "5:wan"
+ ;;
+
*)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
wrt160nl)
status_led="wrt160nl:blue:wps"
;;
+ z1)
+ status_led="z1:green:tricolor0"
+ ;;
zbt-we1526)
status_led="zbt-we1526:green:status"
;;
ath9k_eeprom_extract "caldata" 4096 2048
ath9k_patch_firmware_mac $(mtd_get_mac_binary caldata 0)
;;
+ z1)
+ . /lib/upgrade/nand.sh
+
+ if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
+ ath9k_ubi_eeprom_extract "caldata" 4096 2048
+ else
+ ath9k_eeprom_extract "origcaldata" 4096 2048
+ fi
+ ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +2)
+ ;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;
ath9k_eeprom_extract "caldata" 20480 2048
ath9k_patch_firmware_mac $(mtd_get_mac_binary caldata 12)
;;
+ z1)
+ . /lib/upgrade/nand.sh
+
+ if [ -n "$(nand_find_volume ubi0 caldata)" ]; then
+ ath9k_ubi_eeprom_extract "caldata" 86016 4096
+ else
+ ath9k_eeprom_extract "origcaldata" 86016 4096
+ fi
+ ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary_ubi board-config 102) +3)
+ ;;
*)
ath9k_eeprom_die "board $board is not supported yet"
;;
whr-hp-gn|\
wzr-hp-ag300h|\
wzr-hp-g450h|\
+z1|\
ew-dorin|\
ew-dorin-router)
migrate_switch_name "eth0" "switch0"
*WHR-HP-G300N)
name="whr-hp-g300n"
;;
+ *Z1)
+ name="z1"
+ ;;
*ZBT-WE1526)
name="zbt-we1526"
;;
wrt160nl)
fetch_mac_from_mtd nvram lan_hwaddr wan_hwaddr
;;
+ z1)
+ mac_lan=$(mtd_get_mac_binary_ubi board-config 102)
+ [ -n "$mac_lan" ] && ifconfig eth0 hw ether "$mac_lan"
+ ;;
esac
}
#!/bin/sh
#
-# Copyright (C) 2015 Chris Blake <chrisrblake93@gmail.com>
+# Copyright (C) 2015-2016 Chris Blake <chrisrblake93@gmail.com>
#
# Custom upgrade script for Meraki NAND devices (ex. MR18)
# Based on dir825.sh and stock nand functions
dd bs=1 count=2 skip=$pos if=$mtddev 2>/dev/null | hexdump -v -n 4 -e '1/1 "%02x"'
}
-mr18_is_caldata_valid() {
- local mtddev=$1
+meraki_is_caldata_valid() {
+ local board=$1
+ local mtddev=$2
local magic
- magic=$(get_magic_at $mtddev 4096)
- [ "$magic" != "0202" ] && return 0
+ case "$board" in
+ "mr18")
+ magic=$(get_magic_at $mtddev 4096)
+ [ "$magic" != "0202" ] && return 0
+
+ magic=$(get_magic_at $mtddev 20480)
+ [ "$magic" != "0202" ] && return 0
- magic=$(get_magic_at $mtddev 20480)
- [ "$magic" != "0202" ] && return 0
+ magic=$(get_magic_at $mtddev 36864)
+ [ "$magic" != "0202" ] && return 0
+
+ return 1
+ ;;
+ "z1")
+ magic=$(get_magic_at $mtddev 4096)
+ [ "$magic" != "0202" ] && return 0
- magic=$(get_magic_at $mtddev 36864)
- [ "$magic" != "0202" ] && return 0
+ magic=$(get_magic_at $mtddev 86016)
+ [ "$magic" != "a55a" ] && return 0
- return 1
+ return 1
+ ;;
+ *)
+ return 1
+ ;;
+ esac
}
merakinand_copy_caldata() {
local cal_src=$1
local cal_dst=$2
- local ubidev=$( nand_find_ubi $CI_UBIPART )
+ local ubidev="$(nand_find_ubi $CI_UBIPART)"
local board_name="$(cat /tmp/sysinfo/board_name)"
local rootfs_size="$(ubinfo /dev/ubi0 -N rootfs_data | grep "Size" | awk '{ print $6 }')"
# Setup partitions using board name, in case of future platforms
case "$board_name" in
- "mr18")
+ "mr18"|\
+ "z1")
# Src is MTD
- mtd_src=$(find_mtd_chardev $cal_src)
+ mtd_src="$(find_mtd_chardev $cal_src)"
[ -n "$mtd_src" ] || {
echo "no mtd device found for partition $cal_src"
exit 1
exit 1
}
- mr18_is_caldata_valid "$mtd_src" && {
+ meraki_is_caldata_valid "$board_name" "$mtd_src" && {
echo "no valid calibration data found in $cal_src"
exit 1
}
- mr18_is_caldata_valid "/dev/$mtd_dst" && {
+ meraki_is_caldata_valid "$board_name" "/dev/$mtd_dst" && {
echo "Copying calibration data from $cal_src to $cal_dst..."
dd if="$mtd_src" of=/tmp/caldata.tmp 2>/dev/null
ubiupdatevol "/dev/$mtd_dst" /tmp/caldata.tmp
echo "pass" && return 0
}
;;
+ "z1")
+ [ "$image_magic_word" == "4d495053" ] && {
+ echo "pass" && return 0
+ }
+ ;;
esac
exit 1
local kernel_magic="$(merakinand_do_kernel_check $1 $2)"
case "$board_name" in
- "mr18")
+ "mr18"|\
+ "z1")
[ "$control_length" = 0 -o "$file_type" != "squashfs" -o "$kernel_magic" != "pass" ] && {
echo "Invalid sysupgrade file for $board_name"
return 1
merakinand_copy_caldata "odm-caldata" "caldata"
nand_do_upgrade $1
;;
+ "z1")
+ # Check and create UBI caldata if it's invalid
+ merakinand_copy_caldata "origcaldata" "caldata"
+ nand_do_upgrade $1
+ ;;
*)
echo "Unsupported device $board_name";
exit 1
}
return 0
;;
- mr18)
+ mr18 | \
+ z1 )
merakinand_do_platform_check $board $1
return $?;
;;
wndr4300 )
nand_do_upgrade "$1"
;;
- mr18)
+ mr18 | \
+ z1 )
merakinand_do_upgrade "$1"
;;
esac
CONFIG_ATH79_MACH_WZR_HP_G300NH=y
CONFIG_ATH79_MACH_WZR_HP_G300NH2=y
CONFIG_ATH79_MACH_WZR_HP_G450H=y
+CONFIG_ATH79_MACH_Z1=y
CONFIG_ATH79_MACH_ZBT_WE1526=y
CONFIG_ATH79_MACH_ZCN_1523H=y
CONFIG_ATH79_NVRAM=y
select ATH79_DEV_WMAC
select ATH79_NVRAM
+config ATH79_MACH_Z1
+ bool "Meraki Z1 board support"
+ select SOC_AR934X
+ select ATH79_DEV_AP9X_PCI if PCI
+ select ATH79_DEV_ETH
+ select ATH79_DEV_GPIO_BUTTONS
+ select ATH79_DEV_LEDS_GPIO
+ select ATH79_DEV_NFC
+ select ATH79_DEV_USB
+ select ATH79_DEV_WMAC
+ select LEDS_NU801
+
config ATH79_MACH_ZBT_WE1526
bool "Zbtlink ZBT-WE1526 board support"
select SOC_QCA953X
obj-$(CONFIG_ATH79_MACH_WZR_HP_AG300H) += mach-wzr-hp-ag300h.o
obj-$(CONFIG_ATH79_MACH_WZR_HP_G450H) += mach-wzr-hp-g450h.o
obj-$(CONFIG_ATH79_MACH_WZR_450HP2) += mach-wzr-450hp2.o
+obj-$(CONFIG_ATH79_MACH_Z1) += mach-z1.o
obj-$(CONFIG_ATH79_MACH_ZBT_WE1526) += mach-zbt-we1526.o
obj-$(CONFIG_ATH79_MACH_ZCN_1523H) += mach-zcn-1523h.o
obj-$(CONFIG_ATH79_MACH_CARAMBOLA2) += mach-carambola2.o
--- /dev/null
+/*
+ * Cisco Meraki Z1 board support
+ *
+ * Copyright (C) 2016 Chris Blake <chrisrblake93@gmail.com>
+ * Copyright (C) 2016 Christian Lamparter <chunkeey@googlemail.com>
+ *
+ * Based on Cisco Meraki GPL Release r23-20150601 Z1 Device Config
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+#include <linux/ar8216_platform.h>
+#include <linux/platform/ar934x_nfc.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include <linux/leds-nu801.h>
+#include <linux/firmware.h>
+#include <linux/pci.h>
+
+#include "common.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-nfc.h"
+#include "dev-usb.h"
+#include "dev-wmac.h"
+#include "dev-ap9x-pci.h"
+#include "machtypes.h"
+
+#define Z1_GPIO_LED_POWER_ORANGE 17
+
+#define Z1_GPIO_NU801_CKI 14
+#define Z1_GPIO_NU801_SDI 15
+
+#define Z1_GPIO_XLNA0 18
+#define Z1_GPIO_XLNA1 19
+
+#define Z1_GPIO_BTN_RESET 12
+#define Z1_KEYS_POLL_INTERVAL 20 /* msecs */
+#define Z1_KEYS_DEBOUNCE_INTERVAL (3 * Z1_KEYS_POLL_INTERVAL)
+
+#define Z1_ETH_SWITCH_PHY 0
+
+static struct gpio_led Z1_leds_gpio[] __initdata = {
+ {
+ .name = "z1:orange:power",
+ .gpio = Z1_GPIO_LED_POWER_ORANGE,
+ .active_low = 1,
+ },
+};
+
+static struct gpio_keys_button Z1_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = Z1_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = Z1_GPIO_BTN_RESET,
+ .active_low = 1,
+ },
+};
+
+static struct led_nu801_template tricolor_led_template = {
+ .device_name = "z1",
+ .name = "tricolor",
+ .num_leds = 1,
+ .cki = Z1_GPIO_NU801_CKI,
+ .sdi = Z1_GPIO_NU801_SDI,
+ .lei = -1,
+ .ndelay = 500,
+ .init_brightness = {
+ LED_OFF,
+ LED_OFF,
+ LED_OFF,
+ },
+ .default_trigger = "none",
+};
+
+static struct led_nu801_platform_data tricolor_led_data = {
+ .num_controllers = 1,
+ .template = &tricolor_led_template,
+};
+
+static struct platform_device tricolor_leds = {
+ .name = "leds-nu801",
+ .id = -1,
+ .dev.platform_data = &tricolor_led_data,
+};
+
+static struct ar8327_pad_cfg z1_ar8327_pad0_cfg = {
+ .mode = AR8327_PAD_MAC_RGMII,
+ .txclk_delay_en = true,
+ .rxclk_delay_en = true,
+ .txclk_delay_sel = AR8327_CLK_DELAY_SEL1,
+ .rxclk_delay_sel = AR8327_CLK_DELAY_SEL2,
+};
+
+static struct ar8327_platform_data z1_ar8327_data = {
+ .pad0_cfg = &z1_ar8327_pad0_cfg,
+ .port0_cfg = {
+ .force_link = 1,
+ .speed = AR8327_PORT_SPEED_1000,
+ .duplex = 1,
+ .txpause = 1,
+ .rxpause = 1,
+ },
+};
+
+static struct mdio_board_info z1_mdio0_info[] = {
+ {
+ .bus_id = "ag71xx-mdio.0",
+ .phy_addr = Z1_ETH_SWITCH_PHY,
+ .platform_data = &z1_ar8327_data,
+ },
+};
+
+static void __init z1_setup(void)
+{
+ /* NAND */
+ ath79_nfc_set_ecc_mode(AR934X_NFC_ECC_SOFT_BCH);
+ ath79_register_nfc();
+
+ /* Eth Config */
+ ath79_setup_ar934x_eth_cfg(AR934X_ETH_CFG_RGMII_GMAC0 |
+ AR934X_ETH_CFG_SW_ONLY_MODE);
+
+ /* MDIO Interface */
+ ath79_register_mdio(1, 0x0);
+ ath79_register_mdio(0, 0x0);
+ mdiobus_register_board_info(z1_mdio0_info,
+ ARRAY_SIZE(z1_mdio0_info));
+
+ /* GMAC0 is connected to an AR8327 switch */
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
+ ath79_eth0_data.phy_mask = BIT(Z1_ETH_SWITCH_PHY);
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+ ath79_eth0_pll_data.pll_1000 = 0x06000000;
+ ath79_register_eth(0);
+
+ /* XLNA */
+ ath79_wmac_set_ext_lna_gpio(0, Z1_GPIO_XLNA0);
+ ath79_wmac_set_ext_lna_gpio(1, Z1_GPIO_XLNA1);
+
+ /* LEDs and Buttons */
+ platform_device_register(&tricolor_leds);
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(Z1_leds_gpio),
+ Z1_leds_gpio);
+ ath79_register_gpio_keys_polled(-1, Z1_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(Z1_gpio_keys),
+ Z1_gpio_keys);
+
+ /* USB */
+ ath79_register_usb();
+
+ /* Wireless */
+ ath79_register_wmac_simple();
+ ap91_pci_init_simple();
+}
+MIPS_MACHINE(ATH79_MACH_Z1, "Z1", "Meraki Z1", z1_setup);
ATH79_MACH_WZR_HP_G300NH2, /* Buffalo WZR-HP-G300NH2 */
ATH79_MACH_WZR_HP_G450H, /* Buffalo WZR-HP-G450H */
ATH79_MACH_WZR_450HP2, /* Buffalo WZR-450HP2 */
+ ATH79_MACH_Z1, /* Cisco Meraki Z1 */
ATH79_MACH_ZBT_WE1526, /* Zbtlink ZBT-WE1526 */
ATH79_MACH_ZCN_1523H_2, /* Zcomax ZCN-1523H-2-xx */
ATH79_MACH_ZCN_1523H_5, /* Zcomax ZCN-1523H-5-xx */
endef
TARGET_DEVICES += mr18
+define Build/MerakiNAND-old
+ -$(STAGING_DIR_HOST)/bin/mkmerakifw-old \
+ -B $(BOARDNAME) -s \
+ -i $@ \
+ -o $@.new
+ @mv $@.new $@
+endef
+
+define Device/z1
+ DEVICE_TITLE := Meraki Z1
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-ledtrig-usbdev kmod-spi-gpio kmod-ath9k kmod-owl-loader
+ BOARDNAME = Z1
+ BLOCKSIZE := 64k
+ CONSOLE = ttyS0,115200
+ MTDPARTS = ar934x-nfc:128K(loader1)ro,8064K(kernel),128K(loader2)ro,8064K(recovery),114560K(ubi),128K(origcaldata)ro
+ IMAGES := sysupgrade.tar
+ KERNEL := kernel-bin | patch-cmdline | MerakiNAND-old
+ KERNEL_INITRAMFS := kernel-bin | patch-cmdline | MerakiNAND-old
+ IMAGE/sysupgrade.tar := sysupgrade-tar
+endef
+
+TARGET_DEVICES += z1
+
define LegacyDevice/R6100
DEVICE_TITLE := NETGEAR R6100
DEVICE_PACKAGES := kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev
+config LEDS_NU801
+ tristate "LED driver for NU801 RGB LED"
-+ depends on LEDS_CLASS && ATH79_MACH_MR18
++ depends on LEDS_CLASS && (ATH79_MACH_MR18 || ATH79_MACH_Z1)
+ help
+ This option enables support for NU801 RGB LED driver chips
+ accessed via GPIO.
projects / openwrt / staging / noltari.git / commitdiff