static void ixgbe_release_eeprom(struct ixgbe_hw *hw);
static s32 ixgbe_mta_vector(struct ixgbe_hw *hw, u8 *mc_addr);
-static s32 ixgbe_fc_autoneg_fiber(struct ixgbe_hw *hw);
-static s32 ixgbe_fc_autoneg_backplane(struct ixgbe_hw *hw);
-static s32 ixgbe_fc_autoneg_copper(struct ixgbe_hw *hw);
-static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw);
-static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
- u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm);
-static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num);
static s32 ixgbe_poll_eerd_eewr_done(struct ixgbe_hw *hw, u32 ee_reg);
static s32 ixgbe_read_eeprom_buffer_bit_bang(struct ixgbe_hw *hw, u16 offset,
u16 words, u16 *data);
u16 offset);
static s32 ixgbe_disable_pcie_master(struct ixgbe_hw *hw);
+/**
+ * ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow
+ * control
+ * @hw: pointer to hardware structure
+ *
+ * There are several phys that do not support autoneg flow control. This
+ * function check the device id to see if the associated phy supports
+ * autoneg flow control.
+ **/
+static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
+{
+
+ switch (hw->device_id) {
+ case IXGBE_DEV_ID_X540T:
+ return 0;
+ case IXGBE_DEV_ID_82599_T3_LOM:
+ return 0;
+ default:
+ return IXGBE_ERR_FC_NOT_SUPPORTED;
+ }
+}
+
+/**
+ * ixgbe_setup_fc - Set up flow control
+ * @hw: pointer to hardware structure
+ *
+ * Called at init time to set up flow control.
+ **/
+static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
+{
+ s32 ret_val = 0;
+ u32 reg = 0, reg_bp = 0;
+ u16 reg_cu = 0;
+
+#ifdef CONFIG_DCB
+ if (hw->fc.requested_mode == ixgbe_fc_pfc) {
+ hw->fc.current_mode = hw->fc.requested_mode;
+ goto out;
+ }
+
+#endif /* CONFIG_DCB */
+ /* Validate the packetbuf configuration */
+ if (packetbuf_num < 0 || packetbuf_num > 7) {
+ hw_dbg(hw, "Invalid packet buffer number [%d], expected range is 0-7\n",
+ packetbuf_num);
+ ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ goto out;
+ }
+
+ /*
+ * Validate the water mark configuration. Zero water marks are invalid
+ * because it causes the controller to just blast out fc packets.
+ */
+ if (!hw->fc.low_water ||
+ !hw->fc.high_water[packetbuf_num] ||
+ !hw->fc.pause_time) {
+ hw_dbg(hw, "Invalid water mark configuration\n");
+ ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ goto out;
+ }
+
+ /*
+ * Validate the requested mode. Strict IEEE mode does not allow
+ * ixgbe_fc_rx_pause because it will cause us to fail at UNH.
+ */
+ if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
+ hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict IEEE mode\n");
+ ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ goto out;
+ }
+
+ /*
+ * 10gig parts do not have a word in the EEPROM to determine the
+ * default flow control setting, so we explicitly set it to full.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_default)
+ hw->fc.requested_mode = ixgbe_fc_full;
+
+ /*
+ * Set up the 1G and 10G flow control advertisement registers so the
+ * HW will be able to do fc autoneg once the cable is plugged in. If
+ * we link at 10G, the 1G advertisement is harmless and vice versa.
+ */
+
+ switch (hw->phy.media_type) {
+ case ixgbe_media_type_fiber:
+ case ixgbe_media_type_backplane:
+ reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
+ reg_bp = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ break;
+
+ case ixgbe_media_type_copper:
+ hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
+ MDIO_MMD_AN, ®_cu);
+ break;
+
+ default:
+ ;
+ }
+
+ /*
+ * The possible values of fc.requested_mode are:
+ * 0: Flow control is completely disabled
+ * 1: Rx flow control is enabled (we can receive pause frames,
+ * but not send pause frames).
+ * 2: Tx flow control is enabled (we can send pause frames but
+ * we do not support receiving pause frames).
+ * 3: Both Rx and Tx flow control (symmetric) are enabled.
+#ifdef CONFIG_DCB
+ * 4: Priority Flow Control is enabled.
+#endif
+ * other: Invalid.
+ */
+ switch (hw->fc.requested_mode) {
+ case ixgbe_fc_none:
+ /* Flow control completely disabled by software override. */
+ reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+ if (hw->phy.media_type == ixgbe_media_type_backplane)
+ reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE |
+ IXGBE_AUTOC_ASM_PAUSE);
+ else if (hw->phy.media_type == ixgbe_media_type_copper)
+ reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
+ break;
+ case ixgbe_fc_rx_pause:
+ /*
+ * Rx Flow control is enabled and Tx Flow control is
+ * disabled by software override. Since there really
+ * isn't a way to advertise that we are capable of RX
+ * Pause ONLY, we will advertise that we support both
+ * symmetric and asymmetric Rx PAUSE. Later, we will
+ * disable the adapter's ability to send PAUSE frames.
+ */
+ reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+ if (hw->phy.media_type == ixgbe_media_type_backplane)
+ reg_bp |= (IXGBE_AUTOC_SYM_PAUSE |
+ IXGBE_AUTOC_ASM_PAUSE);
+ else if (hw->phy.media_type == ixgbe_media_type_copper)
+ reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
+ break;
+ case ixgbe_fc_tx_pause:
+ /*
+ * Tx Flow control is enabled, and Rx Flow control is
+ * disabled by software override.
+ */
+ reg |= (IXGBE_PCS1GANA_ASM_PAUSE);
+ reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE);
+ if (hw->phy.media_type == ixgbe_media_type_backplane) {
+ reg_bp |= (IXGBE_AUTOC_ASM_PAUSE);
+ reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE);
+ } else if (hw->phy.media_type == ixgbe_media_type_copper) {
+ reg_cu |= (IXGBE_TAF_ASM_PAUSE);
+ reg_cu &= ~(IXGBE_TAF_SYM_PAUSE);
+ }
+ break;
+ case ixgbe_fc_full:
+ /* Flow control (both Rx and Tx) is enabled by SW override. */
+ reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
+ if (hw->phy.media_type == ixgbe_media_type_backplane)
+ reg_bp |= (IXGBE_AUTOC_SYM_PAUSE |
+ IXGBE_AUTOC_ASM_PAUSE);
+ else if (hw->phy.media_type == ixgbe_media_type_copper)
+ reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
+ break;
+#ifdef CONFIG_DCB
+ case ixgbe_fc_pfc:
+ goto out;
+ break;
+#endif /* CONFIG_DCB */
+ default:
+ hw_dbg(hw, "Flow control param set incorrectly\n");
+ ret_val = IXGBE_ERR_CONFIG;
+ goto out;
+ break;
+ }
+
+ if (hw->mac.type != ixgbe_mac_X540) {
+ /*
+ * Enable auto-negotiation between the MAC & PHY;
+ * the MAC will advertise clause 37 flow control.
+ */
+ IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
+ reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
+
+ /* Disable AN timeout */
+ if (hw->fc.strict_ieee)
+ reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
+
+ IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
+ hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
+ }
+
+ /*
+ * AUTOC restart handles negotiation of 1G and 10G on backplane
+ * and copper. There is no need to set the PCS1GCTL register.
+ *
+ */
+ if (hw->phy.media_type == ixgbe_media_type_backplane) {
+ reg_bp |= IXGBE_AUTOC_AN_RESTART;
+ IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_bp);
+ } else if ((hw->phy.media_type == ixgbe_media_type_copper) &&
+ (ixgbe_device_supports_autoneg_fc(hw) == 0)) {
+ hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE,
+ MDIO_MMD_AN, reg_cu);
+ }
+
+ hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
+out:
+ return ret_val;
+}
+
/**
* ixgbe_start_hw_generic - Prepare hardware for Tx/Rx
* @hw: pointer to hardware structure
}
/**
- * ixgbe_fc_autoneg - Configure flow control
+ * ixgbe_negotiate_fc - Negotiate flow control
* @hw: pointer to hardware structure
+ * @adv_reg: flow control advertised settings
+ * @lp_reg: link partner's flow control settings
+ * @adv_sym: symmetric pause bit in advertisement
+ * @adv_asm: asymmetric pause bit in advertisement
+ * @lp_sym: symmetric pause bit in link partner advertisement
+ * @lp_asm: asymmetric pause bit in link partner advertisement
*
- * Compares our advertised flow control capabilities to those advertised by
- * our link partner, and determines the proper flow control mode to use.
+ * Find the intersection between advertised settings and link partner's
+ * advertised settings
**/
-void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
+static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
+ u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
{
- s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED;
- ixgbe_link_speed speed;
- bool link_up;
-
- /*
- * AN should have completed when the cable was plugged in.
- * Look for reasons to bail out. Bail out if:
- * - FC autoneg is disabled, or if
- * - link is not up.
- *
- * Since we're being called from an LSC, link is already known to be up.
- * So use link_up_wait_to_complete=false.
- */
- if (hw->fc.disable_fc_autoneg)
- goto out;
-
- hw->mac.ops.check_link(hw, &speed, &link_up, false);
- if (!link_up)
- goto out;
-
- switch (hw->phy.media_type) {
- /* Autoneg flow control on fiber adapters */
- case ixgbe_media_type_fiber:
- if (speed == IXGBE_LINK_SPEED_1GB_FULL)
- ret_val = ixgbe_fc_autoneg_fiber(hw);
- break;
-
- /* Autoneg flow control on backplane adapters */
- case ixgbe_media_type_backplane:
- ret_val = ixgbe_fc_autoneg_backplane(hw);
- break;
+ if ((!(adv_reg)) || (!(lp_reg)))
+ return IXGBE_ERR_FC_NOT_NEGOTIATED;
- /* Autoneg flow control on copper adapters */
- case ixgbe_media_type_copper:
- if (ixgbe_device_supports_autoneg_fc(hw) == 0)
- ret_val = ixgbe_fc_autoneg_copper(hw);
- break;
-
- default:
- break;
- }
-
-out:
- if (ret_val == 0) {
- hw->fc.fc_was_autonegged = true;
+ if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) {
+ /*
+ * Now we need to check if the user selected Rx ONLY
+ * of pause frames. In this case, we had to advertise
+ * FULL flow control because we could not advertise RX
+ * ONLY. Hence, we must now check to see if we need to
+ * turn OFF the TRANSMISSION of PAUSE frames.
+ */
+ if (hw->fc.requested_mode == ixgbe_fc_full) {
+ hw->fc.current_mode = ixgbe_fc_full;
+ hw_dbg(hw, "Flow Control = FULL.\n");
+ } else {
+ hw->fc.current_mode = ixgbe_fc_rx_pause;
+ hw_dbg(hw, "Flow Control=RX PAUSE frames only\n");
+ }
+ } else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) &&
+ (lp_reg & lp_sym) && (lp_reg & lp_asm)) {
+ hw->fc.current_mode = ixgbe_fc_tx_pause;
+ hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
+ } else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) &&
+ !(lp_reg & lp_sym) && (lp_reg & lp_asm)) {
+ hw->fc.current_mode = ixgbe_fc_rx_pause;
+ hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
} else {
- hw->fc.fc_was_autonegged = false;
- hw->fc.current_mode = hw->fc.requested_mode;
+ hw->fc.current_mode = ixgbe_fc_none;
+ hw_dbg(hw, "Flow Control = NONE.\n");
}
+ return 0;
}
/**
}
/**
- * ixgbe_negotiate_fc - Negotiate flow control
- * @hw: pointer to hardware structure
- * @adv_reg: flow control advertised settings
- * @lp_reg: link partner's flow control settings
- * @adv_sym: symmetric pause bit in advertisement
- * @adv_asm: asymmetric pause bit in advertisement
- * @lp_sym: symmetric pause bit in link partner advertisement
- * @lp_asm: asymmetric pause bit in link partner advertisement
- *
- * Find the intersection between advertised settings and link partner's
- * advertised settings
- **/
-static s32 ixgbe_negotiate_fc(struct ixgbe_hw *hw, u32 adv_reg, u32 lp_reg,
- u32 adv_sym, u32 adv_asm, u32 lp_sym, u32 lp_asm)
-{
- if ((!(adv_reg)) || (!(lp_reg)))
- return IXGBE_ERR_FC_NOT_NEGOTIATED;
-
- if ((adv_reg & adv_sym) && (lp_reg & lp_sym)) {
- /*
- * Now we need to check if the user selected Rx ONLY
- * of pause frames. In this case, we had to advertise
- * FULL flow control because we could not advertise RX
- * ONLY. Hence, we must now check to see if we need to
- * turn OFF the TRANSMISSION of PAUSE frames.
- */
- if (hw->fc.requested_mode == ixgbe_fc_full) {
- hw->fc.current_mode = ixgbe_fc_full;
- hw_dbg(hw, "Flow Control = FULL.\n");
- } else {
- hw->fc.current_mode = ixgbe_fc_rx_pause;
- hw_dbg(hw, "Flow Control=RX PAUSE frames only\n");
- }
- } else if (!(adv_reg & adv_sym) && (adv_reg & adv_asm) &&
- (lp_reg & lp_sym) && (lp_reg & lp_asm)) {
- hw->fc.current_mode = ixgbe_fc_tx_pause;
- hw_dbg(hw, "Flow Control = TX PAUSE frames only.\n");
- } else if ((adv_reg & adv_sym) && (adv_reg & adv_asm) &&
- !(lp_reg & lp_sym) && (lp_reg & lp_asm)) {
- hw->fc.current_mode = ixgbe_fc_rx_pause;
- hw_dbg(hw, "Flow Control = RX PAUSE frames only.\n");
- } else {
- hw->fc.current_mode = ixgbe_fc_none;
- hw_dbg(hw, "Flow Control = NONE.\n");
- }
- return 0;
-}
-
-/**
- * ixgbe_setup_fc - Set up flow control
+ * ixgbe_fc_autoneg - Configure flow control
* @hw: pointer to hardware structure
*
- * Called at init time to set up flow control.
+ * Compares our advertised flow control capabilities to those advertised by
+ * our link partner, and determines the proper flow control mode to use.
**/
-static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
+void ixgbe_fc_autoneg(struct ixgbe_hw *hw)
{
- s32 ret_val = 0;
- u32 reg = 0, reg_bp = 0;
- u16 reg_cu = 0;
-
-#ifdef CONFIG_DCB
- if (hw->fc.requested_mode == ixgbe_fc_pfc) {
- hw->fc.current_mode = hw->fc.requested_mode;
- goto out;
- }
-
-#endif /* CONFIG_DCB */
- /* Validate the packetbuf configuration */
- if (packetbuf_num < 0 || packetbuf_num > 7) {
- hw_dbg(hw, "Invalid packet buffer number [%d], expected range "
- "is 0-7\n", packetbuf_num);
- ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
- goto out;
- }
+ s32 ret_val = IXGBE_ERR_FC_NOT_NEGOTIATED;
+ ixgbe_link_speed speed;
+ bool link_up;
/*
- * Validate the water mark configuration. Zero water marks are invalid
- * because it causes the controller to just blast out fc packets.
+ * AN should have completed when the cable was plugged in.
+ * Look for reasons to bail out. Bail out if:
+ * - FC autoneg is disabled, or if
+ * - link is not up.
+ *
+ * Since we're being called from an LSC, link is already known to be up.
+ * So use link_up_wait_to_complete=false.
*/
- if (!hw->fc.low_water ||
- !hw->fc.high_water[packetbuf_num] ||
- !hw->fc.pause_time) {
- hw_dbg(hw, "Invalid water mark configuration\n");
- ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ if (hw->fc.disable_fc_autoneg)
goto out;
- }
- /*
- * Validate the requested mode. Strict IEEE mode does not allow
- * ixgbe_fc_rx_pause because it will cause us to fail at UNH.
- */
- if (hw->fc.strict_ieee && hw->fc.requested_mode == ixgbe_fc_rx_pause) {
- hw_dbg(hw, "ixgbe_fc_rx_pause not valid in strict "
- "IEEE mode\n");
- ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
+ hw->mac.ops.check_link(hw, &speed, &link_up, false);
+ if (!link_up)
goto out;
- }
-
- /*
- * 10gig parts do not have a word in the EEPROM to determine the
- * default flow control setting, so we explicitly set it to full.
- */
- if (hw->fc.requested_mode == ixgbe_fc_default)
- hw->fc.requested_mode = ixgbe_fc_full;
-
- /*
- * Set up the 1G and 10G flow control advertisement registers so the
- * HW will be able to do fc autoneg once the cable is plugged in. If
- * we link at 10G, the 1G advertisement is harmless and vice versa.
- */
switch (hw->phy.media_type) {
+ /* Autoneg flow control on fiber adapters */
case ixgbe_media_type_fiber:
+ if (speed == IXGBE_LINK_SPEED_1GB_FULL)
+ ret_val = ixgbe_fc_autoneg_fiber(hw);
+ break;
+
+ /* Autoneg flow control on backplane adapters */
case ixgbe_media_type_backplane:
- reg = IXGBE_READ_REG(hw, IXGBE_PCS1GANA);
- reg_bp = IXGBE_READ_REG(hw, IXGBE_AUTOC);
+ ret_val = ixgbe_fc_autoneg_backplane(hw);
break;
+ /* Autoneg flow control on copper adapters */
case ixgbe_media_type_copper:
- hw->phy.ops.read_reg(hw, MDIO_AN_ADVERTISE,
- MDIO_MMD_AN, ®_cu);
+ if (ixgbe_device_supports_autoneg_fc(hw) == 0)
+ ret_val = ixgbe_fc_autoneg_copper(hw);
break;
default:
- ;
- }
-
- /*
- * The possible values of fc.requested_mode are:
- * 0: Flow control is completely disabled
- * 1: Rx flow control is enabled (we can receive pause frames,
- * but not send pause frames).
- * 2: Tx flow control is enabled (we can send pause frames but
- * we do not support receiving pause frames).
- * 3: Both Rx and Tx flow control (symmetric) are enabled.
-#ifdef CONFIG_DCB
- * 4: Priority Flow Control is enabled.
-#endif
- * other: Invalid.
- */
- switch (hw->fc.requested_mode) {
- case ixgbe_fc_none:
- /* Flow control completely disabled by software override. */
- reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
- if (hw->phy.media_type == ixgbe_media_type_backplane)
- reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE |
- IXGBE_AUTOC_ASM_PAUSE);
- else if (hw->phy.media_type == ixgbe_media_type_copper)
- reg_cu &= ~(IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
- break;
- case ixgbe_fc_rx_pause:
- /*
- * Rx Flow control is enabled and Tx Flow control is
- * disabled by software override. Since there really
- * isn't a way to advertise that we are capable of RX
- * Pause ONLY, we will advertise that we support both
- * symmetric and asymmetric Rx PAUSE. Later, we will
- * disable the adapter's ability to send PAUSE frames.
- */
- reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
- if (hw->phy.media_type == ixgbe_media_type_backplane)
- reg_bp |= (IXGBE_AUTOC_SYM_PAUSE |
- IXGBE_AUTOC_ASM_PAUSE);
- else if (hw->phy.media_type == ixgbe_media_type_copper)
- reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
break;
- case ixgbe_fc_tx_pause:
- /*
- * Tx Flow control is enabled, and Rx Flow control is
- * disabled by software override.
- */
- reg |= (IXGBE_PCS1GANA_ASM_PAUSE);
- reg &= ~(IXGBE_PCS1GANA_SYM_PAUSE);
- if (hw->phy.media_type == ixgbe_media_type_backplane) {
- reg_bp |= (IXGBE_AUTOC_ASM_PAUSE);
- reg_bp &= ~(IXGBE_AUTOC_SYM_PAUSE);
- } else if (hw->phy.media_type == ixgbe_media_type_copper) {
- reg_cu |= (IXGBE_TAF_ASM_PAUSE);
- reg_cu &= ~(IXGBE_TAF_SYM_PAUSE);
- }
- break;
- case ixgbe_fc_full:
- /* Flow control (both Rx and Tx) is enabled by SW override. */
- reg |= (IXGBE_PCS1GANA_SYM_PAUSE | IXGBE_PCS1GANA_ASM_PAUSE);
- if (hw->phy.media_type == ixgbe_media_type_backplane)
- reg_bp |= (IXGBE_AUTOC_SYM_PAUSE |
- IXGBE_AUTOC_ASM_PAUSE);
- else if (hw->phy.media_type == ixgbe_media_type_copper)
- reg_cu |= (IXGBE_TAF_SYM_PAUSE | IXGBE_TAF_ASM_PAUSE);
- break;
-#ifdef CONFIG_DCB
- case ixgbe_fc_pfc:
- goto out;
- break;
-#endif /* CONFIG_DCB */
- default:
- hw_dbg(hw, "Flow control param set incorrectly\n");
- ret_val = IXGBE_ERR_CONFIG;
- goto out;
- break;
- }
-
- if (hw->mac.type != ixgbe_mac_X540) {
- /*
- * Enable auto-negotiation between the MAC & PHY;
- * the MAC will advertise clause 37 flow control.
- */
- IXGBE_WRITE_REG(hw, IXGBE_PCS1GANA, reg);
- reg = IXGBE_READ_REG(hw, IXGBE_PCS1GLCTL);
-
- /* Disable AN timeout */
- if (hw->fc.strict_ieee)
- reg &= ~IXGBE_PCS1GLCTL_AN_1G_TIMEOUT_EN;
-
- IXGBE_WRITE_REG(hw, IXGBE_PCS1GLCTL, reg);
- hw_dbg(hw, "Set up FC; PCS1GLCTL = 0x%08X\n", reg);
}
- /*
- * AUTOC restart handles negotiation of 1G and 10G on backplane
- * and copper. There is no need to set the PCS1GCTL register.
- *
- */
- if (hw->phy.media_type == ixgbe_media_type_backplane) {
- reg_bp |= IXGBE_AUTOC_AN_RESTART;
- IXGBE_WRITE_REG(hw, IXGBE_AUTOC, reg_bp);
- } else if ((hw->phy.media_type == ixgbe_media_type_copper) &&
- (ixgbe_device_supports_autoneg_fc(hw) == 0)) {
- hw->phy.ops.write_reg(hw, MDIO_AN_ADVERTISE,
- MDIO_MMD_AN, reg_cu);
- }
-
- hw_dbg(hw, "Set up FC; IXGBE_AUTOC = 0x%08X\n", reg);
out:
- return ret_val;
+ if (ret_val == 0) {
+ hw->fc.fc_was_autonegged = true;
+ } else {
+ hw->fc.fc_was_autonegged = false;
+ hw->fc.current_mode = hw->fc.requested_mode;
+ }
}
/**
return 0;
}
-/**
- * ixgbe_device_supports_autoneg_fc - Check if phy supports autoneg flow
- * control
- * @hw: pointer to hardware structure
- *
- * There are several phys that do not support autoneg flow control. This
- * function check the device id to see if the associated phy supports
- * autoneg flow control.
- **/
-static s32 ixgbe_device_supports_autoneg_fc(struct ixgbe_hw *hw)
-{
-
- switch (hw->device_id) {
- case IXGBE_DEV_ID_X540T:
- return 0;
- case IXGBE_DEV_ID_82599_T3_LOM:
- return 0;
- default:
- return IXGBE_ERR_FC_NOT_SUPPORTED;
- }
-}
-
/**
* ixgbe_set_mac_anti_spoofing - Enable/Disable MAC anti-spoofing
* @hw: pointer to hardware structure
projects / openwrt / staging / blogic.git / commitdiff