These boards have not been converted to generic board by the deadline.
Remove dm355evm, dm355leopard, dm365evm, dm6467evm, dvevm, ea20, schmoogie,
sffsdr, sonata.
Signed-off-by: Simon Glass <sjg@chromium.org>
bool "DA850 EVM board"
select SUPPORT_SPL
-config TARGET_OMAPL138_LCDK
- bool "OMAPL138 LCDK"
- select SUPPORT_SPL
-
-config TARGET_DAVINCI_DM355EVM
- bool "DM355 EVM board"
-
-config TARGET_DAVINCI_DM355LEOPARD
- bool "DM355 Leopard board"
-
-config TARGET_DAVINCI_DM365EVM
- bool "DM365 EVM board"
-
-config TARGET_DAVINCI_DM6467EVM
- bool "DM6467 EVM board"
-
-config TARGET_DAVINCI_DVEVM
- bool "DVEVM board"
-
config TARGET_EA20
bool "EA20 board"
-config TARGET_DAVINCI_SCHMOOGIE
- bool "Schmoogie board"
-
-config TARGET_DAVINCI_SFFSDR
- bool "SFFSDR board"
-
-config TARGET_DAVINCI_SONATA
- bool "Sonata board"
+config TARGET_OMAPL138_LCDK
+ bool "OMAPL138 LCDK"
+ select SUPPORT_SPL
config TARGET_CALIMAIN
bool "Calimain board"
source "board/enbw/enbw_cmc/Kconfig"
source "board/Barix/ipam390/Kconfig"
source "board/davinci/da8xxevm/Kconfig"
-source "board/davinci/dm355evm/Kconfig"
-source "board/davinci/dm355leopard/Kconfig"
-source "board/davinci/dm365evm/Kconfig"
-source "board/davinci/dm6467evm/Kconfig"
-source "board/davinci/dvevm/Kconfig"
source "board/davinci/ea20/Kconfig"
-source "board/davinci/schmoogie/Kconfig"
-source "board/davinci/sffsdr/Kconfig"
-source "board/davinci/sonata/Kconfig"
source "board/omicron/calimain/Kconfig"
endif
+++ /dev/null
-if TARGET_DAVINCI_DM355EVM
-
-config SYS_BOARD
- default "dm355evm"
-
-config SYS_VENDOR
- default "davinci"
-
-config SYS_CONFIG_NAME
- default "davinci_dm355evm"
-
-endif
+++ /dev/null
-DM355EVM BOARD
-#M: Sandeep Paulraj <s-paulraj@ti.com>
-S: Orphan (since 2014-08)
-F: board/davinci/dm355evm/
-F: include/configs/davinci_dm355evm.h
-F: configs/davinci_dm355evm_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := dm355evm.o
+++ /dev/null
-#
-# Spectrum Digital DM355 EVM board
-# dm355evm board has 1 bank of 128 MB DDR RAM
-# Physical Address: 8000'0000 to 8800'0000
-#
-# Linux Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-#
-
-#Provide at least 16MB spacing between us and the Linux Kernel image
-CONFIG_SYS_TEXT_BASE = 0x81080000
+++ /dev/null
-/*
- * Copyright (C) 2009 David Brownell
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <nand.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <asm/ti-common/davinci_nand.h>
-#include <asm/arch/davinci_misc.h>
-#include <net.h>
-#include <netdev.h>
-#ifdef CONFIG_DAVINCI_MMC
-#include <mmc.h>
-#include <asm/arch/sdmmc_defs.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * With the DM355 EVM, u-boot is *always* a third stage loader,
- * unless a JTAG debugger handles the first two stages:
- *
- * - 1st stage is ROM Boot Loader (RBL), which searches for a
- * second stage loader in one of three places based on SW7:
- * NAND (with MMC/SD fallback), MMC/SD, or UART.
- *
- * - 2nd stage is User Boot Loader (UBL), using at most 30KB
- * of on-chip SRAM, responsible for lowlevel init, and for
- * loading the third stage loader into DRAM.
- *
- * - 3rd stage, that's us!
- */
-
-int board_init(void)
-{
- gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DM355_EVM;
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- /* We expect the UBL to have handled "lowlevel init", which
- * involves setting up at least:
- * - clocks
- * + PLL1 (for ARM and peripherals) and PLL2 (for DDR)
- * + clock divisors for those PLLs
- * + LPSC_DDR module enabled
- * + LPSC_TIMER0 module (still) enabled
- * - EMIF
- * + DDR init and timings
- * + AEMIF timings (for NAND and DM9000)
- * - pinmux
- *
- * Some of that is repeated here, mostly as a precaution.
- */
-
- /* AEMIF: Some "address" lines are available as GPIOs. A3..A13
- * could be too if we used A12 as a GPIO during NAND chipselect
- * (and Linux did too), letting us control the LED on A7/GPIO61.
- */
- REG(PINMUX2) = 0x0c08;
-
- /* UART0 may still be in SyncReset if we didn't boot from UART */
- davinci_enable_uart0();
-
- /* EDMA may be in SyncReset too; turn it on, Linux won't (yet) */
- lpsc_on(DAVINCI_LPSC_TPCC);
- lpsc_on(DAVINCI_LPSC_TPTC0);
- lpsc_on(DAVINCI_LPSC_TPTC1);
-
- return 0;
-}
-
-#ifdef CONFIG_DRIVER_DM9000
-int board_eth_init(bd_t *bis)
-{
- return dm9000_initialize(bis);
-}
-#endif
-
-#ifdef CONFIG_NAND_DAVINCI
-
-static void nand_dm355evm_select_chip(struct mtd_info *mtd, int chip)
-{
- struct nand_chip *this = mtd->priv;
- unsigned long wbase = (unsigned long) this->IO_ADDR_W;
- unsigned long rbase = (unsigned long) this->IO_ADDR_R;
-
- if (chip == 1) {
- __set_bit(14, &wbase);
- __set_bit(14, &rbase);
- } else {
- __clear_bit(14, &wbase);
- __clear_bit(14, &rbase);
- }
- this->IO_ADDR_W = (void *)wbase;
- this->IO_ADDR_R = (void *)rbase;
-}
-
-int board_nand_init(struct nand_chip *nand)
-{
- davinci_nand_init(nand);
- nand->select_chip = nand_dm355evm_select_chip;
- return 0;
-}
-
-#endif
-
-#ifdef CONFIG_DAVINCI_MMC
-static struct davinci_mmc mmc_sd0 = {
- .reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
- .input_clk = 108000000,
- .host_caps = MMC_MODE_4BIT,
- .voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
- .version = MMC_CTLR_VERSION_1,
-};
-
-#ifdef CONFIG_DAVINCI_MMC_SD1
-static struct davinci_mmc mmc_sd1 = {
- .reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD1_BASE,
- .input_clk = 108000000,
- .host_caps = MMC_MODE_4BIT,
- .voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
- .version = MMC_CTLR_VERSION_1,
-};
-#endif
-
-int board_mmc_init(bd_t *bis)
-{
- int err;
-
- /* Add slot-0 to mmc subsystem */
- err = davinci_mmc_init(bis, &mmc_sd0);
- if (err)
- return err;
-
-#ifdef CONFIG_DAVINCI_MMC_SD1
- /* Add slot-1 to mmc subsystem */
- err = davinci_mmc_init(bis, &mmc_sd1);
-#endif
-
- return err;
-}
-#endif
+++ /dev/null
-if TARGET_DAVINCI_DM355LEOPARD
-
-config SYS_BOARD
- default "dm355leopard"
-
-config SYS_VENDOR
- default "davinci"
-
-config SYS_CONFIG_NAME
- default "davinci_dm355leopard"
-
-endif
+++ /dev/null
-DM355LEOPARD BOARD
-#M: Sandeep Paulraj <s-paulraj@ti.com>
-S: Orphan (since 2014-08)
-F: board/davinci/dm355leopard/
-F: include/configs/davinci_dm355leopard.h
-F: configs/davinci_dm355leopard_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := dm355leopard.o
+++ /dev/null
-# Linux Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-#
-
-#Provide at least 16MB spacing between us and the Linux Kernel image
-CONFIG_SYS_TEXT_BASE = 0x81080000
+++ /dev/null
-/*
- * Copyright (C) 2009 Texas Instruments Incorporated
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <nand.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/gpio.h>
-#include <asm/ti-common/davinci_nand.h>
-#include <asm/arch/davinci_misc.h>
-#include <net.h>
-#include <netdev.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_init(void)
-{
- struct davinci_gpio *gpio01_base =
- (struct davinci_gpio *)DAVINCI_GPIO_BANK01;
- struct davinci_gpio *gpio23_base =
- (struct davinci_gpio *)DAVINCI_GPIO_BANK23;
- struct davinci_gpio *gpio67_base =
- (struct davinci_gpio *)DAVINCI_GPIO_BANK67;
-
- gd->bd->bi_arch_number = MACH_TYPE_DM355_LEOPARD;
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- /* GIO 9 & 10 are used for IO */
- writel((readl(PINMUX3) & 0XF8FFFFFF), PINMUX3);
-
- /* Interrupt set GIO 9 */
- writel((readl(DAVINCI_GPIO_BINTEN) | 0x1), DAVINCI_GPIO_BINTEN);
-
- /* set GIO 9 input */
- writel((readl(&gpio01_base->dir) | (1 << 9)), &gpio01_base->dir);
-
- /* Both edge trigger GIO 9 */
- writel((readl(&gpio01_base->set_rising) | (1 << 9)),
- &gpio01_base->set_rising);
- writel((readl(&gpio01_base->dir) & ~(1 << 5)), &gpio01_base->dir);
-
- /* output low */
- writel((readl(&gpio01_base->set_data) & ~(1 << 5)),
- &gpio01_base->set_data);
-
- /* set GIO 10 output */
- writel((readl(&gpio01_base->dir) & ~(1 << 10)), &gpio01_base->dir);
-
- /* output high */
- writel((readl(&gpio01_base->set_data) | (1 << 10)),
- &gpio01_base->set_data);
-
- /* set GIO 32 output */
- writel((readl(&gpio23_base->dir) & ~(1 << 0)), &gpio23_base->dir);
-
- /* output High */
- writel((readl(&gpio23_base->set_data) | (1 << 0)),
- &gpio23_base->set_data);
-
- /* Enable UART1 MUX Lines */
- writel((readl(PINMUX0) & ~3), PINMUX0);
- writel((readl(&gpio67_base->dir) & ~(1 << 6)), &gpio67_base->dir);
- writel((readl(&gpio67_base->set_data) | (1 << 6)),
- &gpio67_base->set_data);
-
- return 0;
-}
-
-#ifdef CONFIG_DRIVER_DM9000
-int board_eth_init(bd_t *bis)
-{
- return dm9000_initialize(bis);
-}
-#endif
-
-#ifdef CONFIG_NAND_DAVINCI
-int board_nand_init(struct nand_chip *nand)
-{
- davinci_nand_init(nand);
-
- return 0;
-}
-#endif
+++ /dev/null
-if TARGET_DAVINCI_DM365EVM
-
-config SYS_BOARD
- default "dm365evm"
-
-config SYS_VENDOR
- default "davinci"
-
-config SYS_CONFIG_NAME
- default "davinci_dm365evm"
-
-endif
+++ /dev/null
-DM365EVM BOARD
-#M: Sandeep Paulraj <s-paulraj@ti.com>
-S: Orphan (since 2014-08)
-F: board/davinci/dm365evm/
-F: include/configs/davinci_dm365evm.h
-F: configs/davinci_dm365evm_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := dm365evm.o
+++ /dev/null
-#
-# Spectrum Digital DM365 EVM board
-# DM365 EVM board has 1 bank of 128 MB DDR RAM
-# Physical Address: 8000'0000 to 8800'0000
-#
-# Linux Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-#
-
-#Provide at least 16MB spacing between us and the Linux Kernel image
-CONFIG_SYS_TEXT_BASE = 0x81080000
+++ /dev/null
-/*
- * Copyright (C) 2009 Texas Instruments Incorporated
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <nand.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <asm/ti-common/davinci_nand.h>
-#include <asm/arch/gpio.h>
-#include <netdev.h>
-#include <asm/arch/davinci_misc.h>
-#ifdef CONFIG_DAVINCI_MMC
-#include <mmc.h>
-#include <asm/arch/sdmmc_defs.h>
-#endif
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_init(void)
-{
- gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DM365_EVM;
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- return 0;
-}
-
-#ifdef CONFIG_DRIVER_TI_EMAC
-int board_eth_init(bd_t *bis)
-{
- uint8_t eeprom_enetaddr[6];
- int i;
- struct davinci_gpio *gpio1_base =
- (struct davinci_gpio *)DAVINCI_GPIO_BANK01;
-
- /* Configure PINMUX 3 to enable EMAC pins */
- writel((readl(PINMUX3) | 0x1affff), PINMUX3);
-
- /* Configure GPIO20 as output */
- writel((readl(&gpio1_base->dir) & ~(1 << 20)), &gpio1_base->dir);
-
- /* Toggle GPIO 20 */
- for (i = 0; i < 20; i++) {
- /* GPIO 20 low */
- writel((readl(&gpio1_base->out_data) & ~(1 << 20)),
- &gpio1_base->out_data);
-
- udelay(1000);
-
- /* GPIO 20 high */
- writel((readl(&gpio1_base->out_data) | (1 << 20)),
- &gpio1_base->out_data);
- }
-
- /* Configure I2C pins so that EEPROM can be read */
- writel((readl(PINMUX3) | 0x01400000), PINMUX3);
-
- /* Read Ethernet MAC address from EEPROM */
- if (dvevm_read_mac_address(eeprom_enetaddr))
- davinci_sync_env_enetaddr(eeprom_enetaddr);
-
- davinci_emac_initialize();
-
- return 0;
-}
-#endif
-
-#ifdef CONFIG_NAND_DAVINCI
-static void nand_dm365evm_select_chip(struct mtd_info *mtd, int chip)
-{
- struct nand_chip *this = mtd->priv;
- unsigned long wbase = (unsigned long) this->IO_ADDR_W;
- unsigned long rbase = (unsigned long) this->IO_ADDR_R;
-
- if (chip == 1) {
- __set_bit(14, &wbase);
- __set_bit(14, &rbase);
- } else {
- __clear_bit(14, &wbase);
- __clear_bit(14, &rbase);
- }
- this->IO_ADDR_W = (void *)wbase;
- this->IO_ADDR_R = (void *)rbase;
-}
-
-int board_nand_init(struct nand_chip *nand)
-{
- davinci_nand_init(nand);
- nand->select_chip = nand_dm365evm_select_chip;
- return 0;
-}
-#endif
-
-#ifdef CONFIG_DAVINCI_MMC
-static struct davinci_mmc mmc_sd0 = {
- .reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD0_BASE,
- .input_clk = 121500000,
- .host_caps = MMC_MODE_4BIT,
- .voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
- .version = MMC_CTLR_VERSION_2,
-};
-
-#ifdef CONFIG_DAVINCI_MMC_SD1
-static struct davinci_mmc mmc_sd1 = {
- .reg_base = (struct davinci_mmc_regs *)DAVINCI_MMC_SD1_BASE,
- .input_clk = 121500000,
- .host_caps = MMC_MODE_4BIT,
- .voltages = MMC_VDD_32_33 | MMC_VDD_33_34,
- .version = MMC_CTLR_VERSION_2,
-};
-#endif
-
-int board_mmc_init(bd_t *bis)
-{
- int err;
-
- /* Add slot-0 to mmc subsystem */
- err = davinci_mmc_init(bis, &mmc_sd0);
- if (err)
- return err;
-
-#ifdef CONFIG_DAVINCI_MMC_SD1
-#define PUPDCTL1 0x01c4007c
- /* PINMUX(4)-DAT0-3/CMD; PINMUX(0)-CLK */
- writel((readl(PINMUX4) | 0x55400000), PINMUX4);
- writel((readl(PINMUX0) | 0x00010000), PINMUX0);
-
- /* Configure MMC/SD pins as pullup */
- writel((readl(PUPDCTL1) & ~0x07c0), PUPDCTL1);
-
- /* Add slot-1 to mmc subsystem */
- err = davinci_mmc_init(bis, &mmc_sd1);
-#endif
-
- return err;
-}
-#endif
+++ /dev/null
-if TARGET_DAVINCI_DM6467EVM
-
-config SYS_BOARD
- default "dm6467evm"
-
-config SYS_VENDOR
- default "davinci"
-
-config SYS_CONFIG_NAME
- default "davinci_dm6467evm"
-
-endif
+++ /dev/null
-DM6467EVM BOARD
-#M: Sandeep Paulraj <s-paulraj@ti.com>
-S: Orphan (since 2014-08)
-F: board/davinci/dm6467evm/
-F: include/configs/davinci_dm6467evm.h
-F: configs/davinci_dm6467evm_defconfig
-F: configs/davinci_dm6467Tevm_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := dm6467evm.o
+++ /dev/null
-#Provide at least 16MB spacing between us and the Linux Kernel image
-CONFIG_SYS_TEXT_BASE = 0x81080000
+++ /dev/null
-/*
- * Copyright (C) 2009 Texas Instruments Incorporated
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <netdev.h>
-#include <asm/io.h>
-#include <nand.h>
-#include <asm/arch/hardware.h>
-#include <asm/ti-common/davinci_nand.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define REV_DM6467EVM 0
-#define REV_DM6467TEVM 1
-/*
- * get_board_rev() - setup to pass kernel board revision information
- * Returns:
- * bit[0-3] System clock frequency
- * 0000b - 27 MHz
- * 0001b - 33 MHz
- */
-u32 get_board_rev(void)
-{
-
-#ifdef CONFIG_DAVINCI_DM6467TEVM
- return REV_DM6467TEVM;
-#else
- return REV_DM6467EVM;
-#endif
-
-}
-
-int board_init(void)
-{
- gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_DM6467_EVM;
- gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
- lpsc_on(DAVINCI_DM646X_LPSC_TIMER0);
- lpsc_on(DAVINCI_DM646X_LPSC_UART0);
- lpsc_on(DAVINCI_DM646X_LPSC_I2C);
- lpsc_on(DAVINCI_DM646X_LPSC_EMAC);
-
- /* Enable GIO3.3V cells used for EMAC */
- REG(VDD3P3V_PWDN) = 0x80000c0;
-
- /* Select UART function on UART0 */
- REG(PINMUX0) &= ~(0x0000003f << 18);
- REG(PINMUX1) &= ~(0x00000003);
-
- return 0;
-}
-
-#if defined(CONFIG_DRIVER_TI_EMAC)
-
-int board_eth_init(bd_t *bis)
-{
- if (!davinci_emac_initialize()) {
- printf("Error: Ethernet init failed!\n");
- return -1;
- }
-
- return 0;
-}
-#endif /* CONFIG_DRIVER_TI_EMAC */
-
-#ifdef CONFIG_NAND_DAVINCI
-int board_nand_init(struct nand_chip *nand)
-{
- davinci_nand_init(nand);
-
- return 0;
-}
-#endif
+++ /dev/null
-if TARGET_DAVINCI_DVEVM
-
-config SYS_BOARD
- default "dvevm"
-
-config SYS_VENDOR
- default "davinci"
-
-config SYS_CONFIG_NAME
- default "davinci_dvevm"
-
-endif
+++ /dev/null
-DVEVM BOARD
-#M: -
-S: Maintained
-F: board/davinci/dvevm/
-F: include/configs/davinci_dvevm.h
-F: configs/davinci_dvevm_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := dvevm.o
-obj-y += board_init.o
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * Board-specific low level initialization code. Called at the very end
- * of arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S. Just returns if there is no
- * initialization required.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-
-.globl dv_board_init
-dv_board_init:
-
- mov pc, lr
+++ /dev/null
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Swaminathan <swami.iyer@ti.com>
-#
-# Davinci EVM board (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# Davinci EVM has 1 bank of 256 MB DDR RAM
-# Physical Address:
-# 8000'0000 to 9000'0000
-#
-# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
-#
-# Visioneering Corp. Sonata board (ARM926EJS) cpu
-#
-# Sonata board has 1 bank of 128 MB DDR RAM
-# Physical Address:
-# 8000'0000 to 8800'0000
-#
-# Razorstream, LLC. SCHMOOGIE board (ARM926EJS) cpu
-#
-# Schmoogie board has 1 bank of 128 MB DDR RAM
-# Physical Address:
-# 8000'0000 to 8800'0000
-#
-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-#
-# we load ourself to 8108 '0000
-#
-#
-
-#Provide at least 16MB spacing between us and the Linux Kernel image
-CONFIG_SYS_TEXT_BASE = 0x81080000
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * Parts are shamelessly stolen from various TI sources, original copyright
- * follows:
- * -----------------------------------------------------------------
- *
- * Copyright (C) 2004 Texas Instruments.
- *
- * ----------------------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- * ----------------------------------------------------------------------------
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/davinci_misc.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_init(void)
-{
- /* arch number of the board */
- gd->bd->bi_arch_number = MACH_TYPE_DAVINCI_EVM;
-
- /* address of boot parameters */
- gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
-
- /* Configure AEMIF pins (although this should be configured at boot time
- * with pull-up/pull-down resistors) */
- REG(PINMUX0) = 0x00000c1f;
-
- davinci_errata_workarounds();
-
- /* Power on required peripherals */
- lpsc_on(DAVINCI_LPSC_GPIO);
- lpsc_on(DAVINCI_LPSC_USB);
-
-#if !defined(CONFIG_SYS_USE_DSPLINK)
- /* Powerup the DSP */
- dsp_on();
-#endif /* CONFIG_SYS_USE_DSPLINK */
-
- davinci_enable_uart0();
- davinci_enable_emac();
- davinci_enable_i2c();
-
- lpsc_on(DAVINCI_LPSC_TIMER1);
- timer_init();
-
- return(0);
-}
-
-int misc_init_r(void)
-{
- uint8_t video_mode;
- uint8_t eeprom_enetaddr[6];
-
- /* Read Ethernet MAC address from EEPROM if available. */
- if (dvevm_read_mac_address(eeprom_enetaddr))
- davinci_sync_env_enetaddr(eeprom_enetaddr);
-
- i2c_read(0x39, 0x00, 1, &video_mode, 1);
-
- setenv("videostd", ((video_mode & 0x80) ? "pal" : "ntsc"));
-
- return(0);
-}
-
-#ifdef CONFIG_USB_DAVINCI
-
-/* IO Expander I2C address and USB VBUS enable mask */
-#define IOEXP_I2C_ADDR 0x3A
-#define IOEXP_VBUSEN_MASK 1
-
-/*
- * This function enables USB VBUS by writting to IO expander using I2C.
- * Note that the I2C is already initialized at this stage. This
- * function is used by davinci specific USB wrapper code.
- */
-void enable_vbus(void)
-{
- uchar data; /* IO Expander data to enable VBUS */
-
- /* Write to IO expander to enable VBUS */
- i2c_read(IOEXP_I2C_ADDR, 0, 0, &data, 1);
- data &= ~IOEXP_VBUSEN_MASK;
- i2c_write(IOEXP_I2C_ADDR, 0, 0, &data, 1);
-}
-#endif
+++ /dev/null
-if TARGET_DAVINCI_SCHMOOGIE
-
-config SYS_BOARD
- default "schmoogie"
-
-config SYS_VENDOR
- default "davinci"
-
-config SYS_CONFIG_NAME
- default "davinci_schmoogie"
-
-endif
+++ /dev/null
-SCHMOOGIE BOARD
-#M: -
-S: Maintained
-F: board/davinci/schmoogie/
-F: include/configs/davinci_schmoogie.h
-F: configs/davinci_schmoogie_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := schmoogie.o
-obj-y += board_init.o
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * Board-specific low level initialization code. Called at the very end
- * of arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S. Just returns if there is no
- * initialization required.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-
-.globl dv_board_init
-dv_board_init:
-
- mov pc, lr
+++ /dev/null
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Swaminathan <swami.iyer@ti.com>
-#
-# Davinci EVM board (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# Davinci EVM has 1 bank of 256 MB DDR RAM
-# Physical Address:
-# 8000'0000 to 9000'0000
-#
-# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
-#
-# Visioneering Corp. Sonata board (ARM926EJS) cpu
-#
-# Sonata board has 1 bank of 128 MB DDR RAM
-# Physical Address:
-# 8000'0000 to 8800'0000
-#
-# Razorstream, LLC. SCHMOOGIE board (ARM926EJS) cpu
-#
-# Schmoogie board has 1 bank of 128 MB DDR RAM
-# Physical Address:
-# 8000'0000 to 8800'0000
-#
-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-#
-# we load ourself to 8108 '0000
-#
-#
-
-#Provide at least 16MB spacing between us and the Linux Kernel image
-CONFIG_SYS_TEXT_BASE = 0x81080000
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * Parts are shamelessly stolen from various TI sources, original copyright
- * follows:
- * -----------------------------------------------------------------
- *
- * Copyright (C) 2004 Texas Instruments.
- *
- * ----------------------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- * ----------------------------------------------------------------------------
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/davinci_misc.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_init(void)
-{
- /* address of boot parameters */
- gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
-
- /* Configure AEMIF pins (although this should be configured at boot time
- * with pull-up/pull-down resistors) */
- REG(PINMUX0) = 0x00000c1f;
-
- davinci_errata_workarounds();
-
- /* Power on required peripherals */
- lpsc_on(DAVINCI_LPSC_GPIO);
-
-#if !defined(CONFIG_SYS_USE_DSPLINK)
- /* Powerup the DSP */
- dsp_on();
-#endif /* CONFIG_SYS_USE_DSPLINK */
-
- davinci_enable_uart0();
- davinci_enable_emac();
- davinci_enable_i2c();
-
- lpsc_on(DAVINCI_LPSC_TIMER1);
- timer_init();
-
- return(0);
-}
-
-int misc_init_r(void)
-{
- u_int8_t tmp[20], buf[10];
- int i = 0;
-
- /* Set serial number from UID chip */
- const u_int8_t crc_tbl[256] = {
- 0x00, 0x5e, 0xbc, 0xe2, 0x61, 0x3f, 0xdd, 0x83,
- 0xc2, 0x9c, 0x7e, 0x20, 0xa3, 0xfd, 0x1f, 0x41,
- 0x9d, 0xc3, 0x21, 0x7f, 0xfc, 0xa2, 0x40, 0x1e,
- 0x5f, 0x01, 0xe3, 0xbd, 0x3e, 0x60, 0x82, 0xdc,
- 0x23, 0x7d, 0x9f, 0xc1, 0x42, 0x1c, 0xfe, 0xa0,
- 0xe1, 0xbf, 0x5d, 0x03, 0x80, 0xde, 0x3c, 0x62,
- 0xbe, 0xe0, 0x02, 0x5c, 0xdf, 0x81, 0x63, 0x3d,
- 0x7c, 0x22, 0xc0, 0x9e, 0x1d, 0x43, 0xa1, 0xff,
- 0x46, 0x18, 0xfa, 0xa4, 0x27, 0x79, 0x9b, 0xc5,
- 0x84, 0xda, 0x38, 0x66, 0xe5, 0xbb, 0x59, 0x07,
- 0xdb, 0x85, 0x67, 0x39, 0xba, 0xe4, 0x06, 0x58,
- 0x19, 0x47, 0xa5, 0xfb, 0x78, 0x26, 0xc4, 0x9a,
- 0x65, 0x3b, 0xd9, 0x87, 0x04, 0x5a, 0xb8, 0xe6,
- 0xa7, 0xf9, 0x1b, 0x45, 0xc6, 0x98, 0x7a, 0x24,
- 0xf8, 0xa6, 0x44, 0x1a, 0x99, 0xc7, 0x25, 0x7b,
- 0x3a, 0x64, 0x86, 0xd8, 0x5b, 0x05, 0xe7, 0xb9,
- 0x8c, 0xd2, 0x30, 0x6e, 0xed, 0xb3, 0x51, 0x0f,
- 0x4e, 0x10, 0xf2, 0xac, 0x2f, 0x71, 0x93, 0xcd,
- 0x11, 0x4f, 0xad, 0xf3, 0x70, 0x2e, 0xcc, 0x92,
- 0xd3, 0x8d, 0x6f, 0x31, 0xb2, 0xec, 0x0e, 0x50,
- 0xaf, 0xf1, 0x13, 0x4d, 0xce, 0x90, 0x72, 0x2c,
- 0x6d, 0x33, 0xd1, 0x8f, 0x0c, 0x52, 0xb0, 0xee,
- 0x32, 0x6c, 0x8e, 0xd0, 0x53, 0x0d, 0xef, 0xb1,
- 0xf0, 0xae, 0x4c, 0x12, 0x91, 0xcf, 0x2d, 0x73,
- 0xca, 0x94, 0x76, 0x28, 0xab, 0xf5, 0x17, 0x49,
- 0x08, 0x56, 0xb4, 0xea, 0x69, 0x37, 0xd5, 0x8b,
- 0x57, 0x09, 0xeb, 0xb5, 0x36, 0x68, 0x8a, 0xd4,
- 0x95, 0xcb, 0x29, 0x77, 0xf4, 0xaa, 0x48, 0x16,
- 0xe9, 0xb7, 0x55, 0x0b, 0x88, 0xd6, 0x34, 0x6a,
- 0x2b, 0x75, 0x97, 0xc9, 0x4a, 0x14, 0xf6, 0xa8,
- 0x74, 0x2a, 0xc8, 0x96, 0x15, 0x4b, 0xa9, 0xf7,
- 0xb6, 0xe8, 0x0a, 0x54, 0xd7, 0x89, 0x6b, 0x35
- };
-
- /* Set serial number from UID chip */
- if (i2c_read(CONFIG_SYS_UID_ADDR, 0, 1, buf, 8)) {
- printf("\nUID @ 0x%02x read FAILED!!!\n", CONFIG_SYS_UID_ADDR);
- setenv("serial#", "FAILED");
- } else {
- if (buf[0] != 0x70) {
- /* Device Family Code */
- printf("\nUID @ 0x%02x read FAILED!!!\n", CONFIG_SYS_UID_ADDR);
- setenv("serial#", "FAILED");
- }
- }
- /* Now check CRC */
- tmp[0] = 0;
- for (i = 0; i < 8; i++)
- tmp[0] = crc_tbl[tmp[0] ^ buf[i]];
-
- if (tmp[0] != 0) {
- printf("\nUID @ 0x%02x - BAD CRC!!!\n", CONFIG_SYS_UID_ADDR);
- setenv("serial#", "FAILED");
- } else {
- /* CRC OK, set "serial" env variable */
- sprintf((char *)&tmp[0], "%02x%02x%02x%02x%02x%02x",
- buf[6], buf[5], buf[4], buf[3], buf[2], buf[1]);
- setenv("serial#", (char *)&tmp[0]);
- }
-
- return(0);
-}
+++ /dev/null
-if TARGET_DAVINCI_SFFSDR
-
-config SYS_BOARD
- default "sffsdr"
-
-config SYS_VENDOR
- default "davinci"
-
-config SYS_CONFIG_NAME
- default "davinci_sffsdr"
-
-endif
+++ /dev/null
-SFFSDR BOARD
-#M: -
-S: Maintained
-F: board/davinci/sffsdr/
-F: include/configs/davinci_sffsdr.h
-F: configs/davinci_sffsdr_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := sffsdr.o
-obj-y += board_init.o
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * Board-specific low level initialization code. Called at the very end
- * of arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S. Just returns if there is no
- * initialization required.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-
-.globl dv_board_init
-dv_board_init:
-
- mov pc, lr
+++ /dev/null
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# Copyright (C) 2008 Lyrtech <www.lyrtech.com>
-# Copyright (C) 2008 Philip Balister, OpenSDR <philip@opensdr.com>
-#
-# Lyrtech SFF SDR board (ARM926EJS) cpu
-#
-# SFF SDR board has 1 bank of 128 MB DDR RAM
-# Physical Address:
-# 8000'0000 to 87FF'FFFF
-#
-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-#
-# Integrity kernel is expected to be at 8000'0000, entry 8000'00D0,
-# up to 81FF'FFFF (uses up to 32 MB of memory for text, heap, etc).
-#
-# we load ourself to 8400'0000 to provide at least 32MB spacing
-# between us and the Integrity kernel image
-CONFIG_SYS_TEXT_BASE = 0x84000000
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * Copyright (C) 2008 Lyrtech <www.lyrtech.com>
- * Copyright (C) 2008 Philip Balister, OpenSDR <philip@opensdr.com>
- *
- * Parts are shamelessly stolen from various TI sources, original copyright
- * follows:
- *
- * Copyright (C) 2004 Texas Instruments.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <i2c.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/davinci_misc.h>
-
-#define DAVINCI_A3CR (0x01E00014) /* EMIF-A CS3 config register. */
-#define DAVINCI_A3CR_VAL (0x3FFFFFFD) /* EMIF-A CS3 value for FPGA. */
-
-#define INTEGRITY_SYSCFG_OFFSET 0x7E8
-#define INTEGRITY_CHECKWORD_OFFSET 0x7F8
-#define INTEGRITY_CHECKWORD_VALUE 0x10ADBEEF
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_init(void)
-{
- /* arch number of the board */
- gd->bd->bi_arch_number = MACH_TYPE_SFFSDR;
-
- /* address of boot parameters */
- gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
-
- davinci_errata_workarounds();
-
- /* Power on required peripherals */
- lpsc_on(DAVINCI_LPSC_GPIO);
-
-#if !defined(CONFIG_SYS_USE_DSPLINK)
- /* Powerup the DSP */
- dsp_on();
-#endif /* CONFIG_SYS_USE_DSPLINK */
-
- davinci_enable_uart0();
- davinci_enable_emac();
- davinci_enable_i2c();
-
- lpsc_on(DAVINCI_LPSC_TIMER1);
- timer_init();
-
- return(0);
-}
-
-/* Read ethernet MAC address from Integrity data structure inside EEPROM.
- * Returns 1 if found, 0 otherwise.
- */
-static int sffsdr_read_mac_address(uint8_t *buf)
-{
- u_int32_t value, mac[2], address;
-
- /* Read Integrity data structure checkword. */
- if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, INTEGRITY_CHECKWORD_OFFSET,
- CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
- goto err;
- if (value != INTEGRITY_CHECKWORD_VALUE)
- return 0;
-
- /* Read SYSCFG structure offset. */
- if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, INTEGRITY_SYSCFG_OFFSET,
- CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
- goto err;
- address = 0x800 + (int) value; /* Address of SYSCFG structure. */
-
- /* Read NET CONFIG structure offset. */
- if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, address,
- CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
- goto err;
- address = 0x800 + (int) value; /* Address of NET CONFIG structure. */
- address += 12; /* Address of NET INTERFACE CONFIG structure. */
-
- /* Read NET INTERFACE CONFIG 2 structure offset. */
- if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, address,
- CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (uint8_t *) &value, 4))
- goto err;
- address = 0x800 + 16 + (int) value; /* Address of NET INTERFACE
- * CONFIG 2 structure. */
-
- /* Read MAC address. */
- if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, address,
- CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (uint8_t *) &mac[0], 8))
- goto err;
-
- buf[0] = mac[0] >> 24;
- buf[1] = mac[0] >> 16;
- buf[2] = mac[0] >> 8;
- buf[3] = mac[0];
- buf[4] = mac[1] >> 24;
- buf[5] = mac[1] >> 16;
-
- return 1; /* Found */
-
-err:
- printf("Read from EEPROM @ 0x%02x failed\n", CONFIG_SYS_I2C_EEPROM_ADDR);
- return 0;
-}
-
-/* Platform dependent initialisation. */
-int misc_init_r(void)
-{
- uint8_t i2cbuf;
- uint8_t eeprom_enetaddr[6];
-
- /* EMIF-A CS3 configuration for FPGA. */
- REG(DAVINCI_A3CR) = DAVINCI_A3CR_VAL;
-
- /* Configure I2C switch (PCA9543) to enable channel 0. */
- i2cbuf = CONFIG_SYS_I2C_PCA9543_ENABLE_CH0;
- if (i2c_write(CONFIG_SYS_I2C_PCA9543_ADDR, 0,
- CONFIG_SYS_I2C_PCA9543_ADDR_LEN, &i2cbuf, 1)) {
- printf("Write to MUX @ 0x%02x failed\n", CONFIG_SYS_I2C_PCA9543_ADDR);
- return 1;
- }
-
- /* Read Ethernet MAC address from EEPROM if available. */
- if (sffsdr_read_mac_address(eeprom_enetaddr))
- davinci_sync_env_enetaddr(eeprom_enetaddr);
-
- return(0);
-}
+++ /dev/null
-if TARGET_DAVINCI_SONATA
-
-config SYS_BOARD
- default "sonata"
-
-config SYS_VENDOR
- default "davinci"
-
-config SYS_CONFIG_NAME
- default "davinci_sonata"
-
-endif
+++ /dev/null
-SONATA BOARD
-#M: -
-S: Maintained
-F: board/davinci/sonata/
-F: include/configs/davinci_sonata.h
-F: configs/davinci_sonata_defconfig
+++ /dev/null
-#
-# (C) Copyright 2000, 2001, 2002
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := sonata.o
-obj-y += board_init.o
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * Board-specific low level initialization code. Called at the very end
- * of arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S. Just returns if there is no
- * initialization required.
- *
- * For _OLDER_ Sonata boards sets up GPIO4 to control NAND WP line. Newer
- * Sonata boards, AFAIK, don't use this so it's just return by default. Ask
- * Visioneering if they reinvented the wheel once again to make sure :)
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <config.h>
-
-.globl dv_board_init
-dv_board_init:
-#ifdef SONATA_BOARD_GPIOWP
- /* Set PINMUX0 to enable GPIO4 */
- ldr r0, _PINMUX0
- ldr r1, GPIO4_EN_MASK
- ldr r2, [r0]
- and r2, r2, r1
- str r2, [r0]
-
- /* Enable GPIO LPSC module */
- ldr r0, PTSTAT
-
-gpio_ptstat_loop1:
- ldr r2, [r0]
- tst r2, $0x00000001
- bne gpio_ptstat_loop1
-
- ldr r1, MDCTL_GPIO
- ldr r2, [r1]
- and r2, r2, $0xfffffff8
- orr r2, r2, $0x00000003
- str r2, [r1]
-
- orr r2, r2, $0x00000200
- str r2, [r1]
-
- ldr r1, PTCMD
- mov r2, $0x00000001
- str r2, [r1]
-
-gpio_ptstat_loop2:
- ldr r2, [r0]
- tst r2, $0x00000001
- bne gpio_ptstat_loop2
-
- ldr r0, MDSTAT_GPIO
-gpio_mdstat_loop:
- ldr r2, [r0]
- and r2, r2, $0x0000001f
- teq r2, $0x00000003
- bne gpio_mdstat_loop
-
- /* GPIO4 -> output */
- ldr r0, GPIO_DIR01
- mov r1, $0x10
- ldr r2, [r0]
- bic r2, r2, r0
- str r2, [r0]
-
- /* Set it to 0 (Write Protect) */
- ldr r0, GPIO_CLR_DATA01
- str r1, [r0]
-#endif
-
- mov pc, lr
-
-#ifdef SONATA_BOARD_GPIOWP
-.ltorg
-
-GPIO4_EN_MASK:
- .word 0xf77fffff
-MDCTL_GPIO:
- .word 0x01c41a68
-MDSTAT_GPIO:
- .word 0x01c41868
-GPIO_DIR01:
- .word 0x01c67010
-GPIO_CLR_DATA01:
- .word 0x01c6701c
-#endif
+++ /dev/null
-#
-# (C) Copyright 2002
-# Gary Jennejohn, DENX Software Engineering, <garyj@denx.de>
-# David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
-#
-# (C) Copyright 2003
-# Texas Instruments, <www.ti.com>
-# Swaminathan <swami.iyer@ti.com>
-#
-# Davinci EVM board (ARM925EJS) cpu
-# see http://www.ti.com/ for more information on Texas Instruments
-#
-# Davinci EVM has 1 bank of 256 MB DDR RAM
-# Physical Address:
-# 8000'0000 to 9000'0000
-#
-# Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
-#
-# Visioneering Corp. Sonata board (ARM926EJS) cpu
-#
-# Sonata board has 1 bank of 128 MB DDR RAM
-# Physical Address:
-# 8000'0000 to 8800'0000
-#
-# Razorstream, LLC. SCHMOOGIE board (ARM926EJS) cpu
-#
-# Schmoogie board has 1 bank of 128 MB DDR RAM
-# Physical Address:
-# 8000'0000 to 8800'0000
-#
-# Linux-Kernel is expected to be at 8000'8000, entry 8000'8000
-# (mem base + reserved)
-#
-# we load ourself to 8108 '0000
-#
-#
-
-#Provide at least 16MB spacing between us and the Linux Kernel image
-CONFIG_SYS_TEXT_BASE = 0x81080000
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * Parts are shamelessly stolen from various TI sources, original copyright
- * follows:
- * -----------------------------------------------------------------
- *
- * Copyright (C) 2004 Texas Instruments.
- *
- * ----------------------------------------------------------------------------
- * SPDX-License-Identifier: GPL-2.0+
- * ----------------------------------------------------------------------------
- */
-
-#include <common.h>
-#include <nand.h>
-#include <asm/ti-common/davinci_nand.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/davinci_misc.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_init(void)
-{
- /* address of boot parameters */
- gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
-
- /* Configure AEMIF pins (although this should be configured at boot time
- * with pull-up/pull-down resistors) */
- REG(PINMUX0) = 0x00000c1f;
-
- davinci_errata_workarounds();
-
- /* Power on required peripherals */
- lpsc_on(DAVINCI_LPSC_GPIO);
-
-#if !defined(CONFIG_SYS_USE_DSPLINK)
- /* Powerup the DSP */
- dsp_on();
-#endif /* CONFIG_SYS_USE_DSPLINK */
-
- davinci_enable_uart0();
- davinci_enable_emac();
- davinci_enable_i2c();
-
- lpsc_on(DAVINCI_LPSC_TIMER1);
- timer_init();
-
- return(0);
-}
-
-int misc_init_r(void)
-{
- uint8_t eeprom_enetaddr[6];
-
- /* Read Ethernet MAC address from EEPROM if available. */
- if (dvevm_read_mac_address(eeprom_enetaddr))
- davinci_sync_env_enetaddr(eeprom_enetaddr);
-
- return(0);
-}
-
-#ifdef CONFIG_NAND_DAVINCI
-
-/* Set WP on deselect, write enable on select */
-static void nand_sonata_select_chip(struct mtd_info *mtd, int chip)
-{
-#define GPIO_SET_DATA01 0x01c67018
-#define GPIO_CLR_DATA01 0x01c6701c
-#define GPIO_NAND_WP (1 << 4)
-#ifdef SONATA_BOARD_GPIOWP
- if (chip < 0) {
- REG(GPIO_CLR_DATA01) |= GPIO_NAND_WP;
- } else {
- REG(GPIO_SET_DATA01) |= GPIO_NAND_WP;
- }
-#endif
-}
-
-int board_nand_init(struct nand_chip *nand)
-{
- davinci_nand_init(nand);
- nand->select_chip = nand_sonata_select_chip;
- return 0;
-}
-
-#endif /* CONFIG_NAND_DAVINCI */
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_DAVINCI=y
-CONFIG_TARGET_DAVINCI_DM355EVM=y
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SYS_PROMPT="DM355 EVM # "
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_DAVINCI=y
-CONFIG_TARGET_DAVINCI_DM355LEOPARD=y
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SYS_PROMPT="DM355 LEOPARD # "
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_DAVINCI=y
-CONFIG_TARGET_DAVINCI_DM365EVM=y
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SYS_PROMPT="DM36x EVM # "
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_DAVINCI=y
-CONFIG_TARGET_DAVINCI_DM6467EVM=y
-CONFIG_SYS_EXTRA_OPTIONS="DAVINCI_DM6467TEVM,REFCLK_FREQ=33000000"
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_SETEXPR is not set
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_DAVINCI=y
-CONFIG_TARGET_DAVINCI_DM6467EVM=y
-CONFIG_SYS_EXTRA_OPTIONS="REFCLK_FREQ=27000000"
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SYS_PROMPT="DM6467 EVM > "
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_DAVINCI=y
-CONFIG_TARGET_DAVINCI_DVEVM=y
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SYS_PROMPT="U-Boot > "
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_DAVINCI=y
-CONFIG_TARGET_DAVINCI_SCHMOOGIE=y
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SYS_PROMPT="U-Boot > "
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_DAVINCI=y
-CONFIG_TARGET_DAVINCI_SFFSDR=y
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SYS_PROMPT="U-Boot > "
+++ /dev/null
-CONFIG_ARM=y
-CONFIG_ARCH_DAVINCI=y
-CONFIG_TARGET_DAVINCI_SONATA=y
-# CONFIG_CMD_BDI is not set
-# CONFIG_CMD_FPGA is not set
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_SYS_PROMPT="U-Boot > "
+++ /dev/null
-/*
- * Copyright (C) 2009 David Brownell
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* Spectrum Digital TMS320DM355 EVM board */
-#define DAVINCI_DM355EVM
-
-#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is a 3rd stage loader */
-#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */
-#define CONFIG_SYS_CONSOLE_INFO_QUIET
-
-/* SoC Configuration */
-#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
-#define CONFIG_SYS_HZ_CLOCK 24000000 /* timer0 freq */
-#define CONFIG_SOC_DM355
-
-/* Memory Info */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM_1 0x80000000
-#define PHYS_SDRAM_1_SIZE (128 << 20) /* 128 MiB */
-
-/* Serial Driver info: UART0 for console */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4
-#define CONFIG_SYS_NS16550_COM1 0x01c20000
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/* Ethernet: external DM9000 */
-#define CONFIG_DRIVER_DM9000 1
-#define CONFIG_DM9000_BASE 0x04014000
-#define DM9000_IO CONFIG_DM9000_BASE
-#define DM9000_DATA (CONFIG_DM9000_BASE + 2)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_DAVINCI
-#define CONFIG_SYS_DAVINCI_I2C_SPEED 400000
-#define CONFIG_SYS_DAVINCI_I2C_SLAVE 0x10 /* SMBus host address */
-
-/* NAND: socketed, two chipselects, normally 2 GBytes */
-#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NAND_CS 2
-#define CONFIG_SYS_NAND_USE_FLASH_BBT
-#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
-#define CONFIG_SYS_NAND_PAGE_2K
-
-#define CONFIG_SYS_NAND_LARGEPAGE
-#define CONFIG_SYS_NAND_BASE_LIST { 0x02000000, }
-/* socket has two chipselects, nCE0 gated by address BIT(14) */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_MAX_CHIPS 2
-
-/* SD/MMC */
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_DAVINCI_MMC
-#define CONFIG_DAVINCI_MMC_SD1
-#define CONFIG_MMC_MBLOCK
-
-/* USB: OTG connector */
-/* NYET -- #define CONFIG_USB_DAVINCI */
-
-/* U-Boot command configuration */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
-#ifdef CONFIG_MMC
-#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_MMC
-#endif
-
-#ifdef CONFIG_NAND_DAVINCI
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_MTD_DEVICE
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_UBI
-#define CONFIG_RBTREE
-#endif
-
-#ifdef CONFIG_USB_DAVINCI
-#define CONFIG_USB_MUSB_HCD
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
-#else
-#undef CONFIG_USB_MUSB_HCD
-#undef CONFIG_CMD_USB
-#undef CONFIG_USB_STORAGE
-#endif
-
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-
-/* U-Boot general configuration */
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE /* Print buffer size */ \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_LONGHELP
-
-#ifdef CONFIG_NAND_DAVINCI
-#define CONFIG_ENV_SIZE (256 << 10) /* 256 KiB */
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0x3C0000
-#undef CONFIG_ENV_IS_IN_FLASH
-#endif
-
-#if defined(CONFIG_MMC) && !defined(CONFIG_ENV_IS_IN_NAND)
-#define CONFIG_CMD_ENV
-#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
-#define CONFIG_ENV_OFFSET (51 << 9) /* Sector 51 */
-#define CONFIG_ENV_IS_IN_MMC
-#undef CONFIG_ENV_IS_IN_FLASH
-#endif
-
-#define CONFIG_BOOTDELAY 5
-#define CONFIG_BOOTCOMMAND \
- "dhcp;bootm"
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200n8 " \
- "root=/dev/mmcblk0p1 rootwait rootfstype=ext3 ro"
-
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_TIMESTAMP
-
-#define CONFIG_NET_RETRY_COUNT 10
-
-/* U-Boot memory configuration */
-#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* 1 MiB */
-#define CONFIG_SYS_MEMTEST_START 0x87000000 /* physical address */
-#define CONFIG_SYS_MEMTEST_END 0x88000000 /* test 16MB RAM */
-
-/* Linux interfacing */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_SYS_BARGSIZE 1024 /* bootarg Size */
-#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* kernel address */
-
-
-/* NAND configuration ... socketed with two chipselects. It normally comes
- * with a 2GByte SLC part with 2KB pages (and 128KB erase blocks); other
- * 2GByte parts may have 4KB pages, 256KB erase blocks, and use MLC. (MLC
- * pretty much demands the 4-bit ECC support.) You can of course swap in
- * other parts, including small page ones.
- *
- * This presents a single read-only partition for all bootloader stuff.
- * UBL (1+ block), U-Boot (256KB+), U-Boot environment (one block), and
- * some extra space to help cope with bad blocks in that data. Linux
- * shouldn't care about its detailed layout, and will probably want to use
- * UBI/UBFS for the rest (except maybe on smallpage chips). It's easy to
- * override this default partitioning using MTDPARTS and cmdlinepart.
- */
-#define MTDIDS_DEFAULT "nand0=davinci_nand.0"
-
-#ifdef CONFIG_SYS_NAND_LARGEPAGE
-/* Use same layout for 128K/256K blocks; allow some bad blocks */
-#define PART_BOOT "2m(bootloader)ro,"
-#else
-/* Assume 16K erase blocks; allow a few bad ones. */
-#define PART_BOOT "512k(bootloader)ro,"
-#endif
-
-#define PART_KERNEL "4m(kernel)," /* kernel + initramfs */
-#define PART_REST "-(filesystem)"
-
-#define MTDPARTS_DEFAULT \
- "mtdparts=davinci_nand.0:" PART_BOOT PART_KERNEL PART_REST
-
-#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * Copyright (C) 2009 Texas Instruments Incorporated
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define DAVINCI_DM355LEOPARD
-
-#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is a 3rd stage loader */
-#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */
-#define CONFIG_SYS_CONSOLE_INFO_QUIET
-
-/* SoC Configuration */
-#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
-#define CONFIG_SYS_HZ_CLOCK 24000000 /* timer0 freq */
-#define CONFIG_SOC_DM355 /* DM355 based board */
-
-/* Memory Info */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM_1 0x80000000
-#define PHYS_SDRAM_1_SIZE (128 << 20) /* 128 MiB */
-
-/* Serial Driver info: UART0 for console */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4
-#define CONFIG_SYS_NS16550_COM1 0x01c20000
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/* Ethernet: external DM9000 */
-#define CONFIG_DRIVER_DM9000 1
-#define CONFIG_DM9000_BASE 0x04000000
-#define DM9000_IO CONFIG_DM9000_BASE
-#define DM9000_DATA (CONFIG_DM9000_BASE + 16)
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_DAVINCI
-#define CONFIG_SYS_DAVINCI_I2C_SPEED 400000
-#define CONFIG_SYS_DAVINCI_I2C_SLAVE 0x10
-
-/* NAND */
-#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NAND_CS 2
-#define CONFIG_SYS_NAND_USE_FLASH_BBT
-#define CONFIG_SYS_NAND_HW_ECC
-
-#define CONFIG_SYS_NAND_BASE_LIST { 0x02000000, }
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-
-/* U-Boot command configuration */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
-#ifdef CONFIG_NAND_DAVINCI
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_MTD_DEVICE
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_UBI
-#define CONFIG_RBTREE
-#endif
-
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-
-/* U-Boot general configuration */
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE /* Print buffer size */ \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_LONGHELP
-
-#ifdef CONFIG_NAND_DAVINCI
-#define CONFIG_ENV_SIZE (256 << 10) /* 256 KiB */
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0x3C0000
-#undef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_OVERWRITE
-#endif
-
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOTCOMMAND "dhcp;bootm"
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200n8 " \
- "root=/dev/mmcblk0p1 rootwait rootfstype=ext3 ro"
-
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_TIMESTAMP
-
-#define CONFIG_NET_RETRY_COUNT 10
-
-/* U-Boot memory configuration */
-#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* 1 MiB */
-#define CONFIG_SYS_MEMTEST_START 0x87000000 /* physical address */
-#define CONFIG_SYS_MEMTEST_END 0x88000000 /* test 16MB RAM */
-
-/* Linux interfacing */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_SYS_BARGSIZE 1024 /* bootarg Size */
-#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* kernel address */
-
-#define MTDIDS_DEFAULT "nand0=davinci_nand.0"
-
-#ifdef CONFIG_SYS_NAND_LARGEPAGE
-#define PART_BOOT "2m(bootloader)ro,"
-#else
-/* Assume 16K erase blocks; allow a few bad ones. */
-#define PART_BOOT "512k(bootloader)ro,"
-#endif
-
-#define PART_KERNEL "4m(kernel)," /* kernel + initramfs */
-#define PART_REST "-(filesystem)"
-
-#define MTDPARTS_DEFAULT \
- "mtdparts=davinci_nand.0:" PART_BOOT PART_KERNEL PART_REST
-
-#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * Copyright (C) 2009 Texas Instruments Incorporated
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* Spectrum Digital TMS320DM365 EVM board */
-#define DAVINCI_DM365EVM
-
-#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is a 3rd stage loader */
-#define CONFIG_SYS_NO_FLASH /* that is, no *NOR* flash */
-#define CONFIG_SYS_CONSOLE_INFO_QUIET
-
-/* SoC Configuration */
-#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
-#define CONFIG_SYS_HZ_CLOCK 24000000 /* timer0 freq */
-#define CONFIG_SOC_DM365
-
-/* Memory Info */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM_1 0x80000000
-#define PHYS_SDRAM_1_SIZE (128 << 20) /* 128 MiB */
-
-/* Serial Driver info: UART0 for console */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4
-#define CONFIG_SYS_NS16550_COM1 0x01c20000
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/* EEPROM definitions for EEPROM on DM365 EVM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-
-/* Network Configuration */
-#define CONFIG_DRIVER_TI_EMAC
-#define CONFIG_MII
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
-
-/* I2C */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_DAVINCI
-#define CONFIG_SYS_DAVINCI_I2C_SPEED 400000
-#define CONFIG_SYS_DAVINCI_I2C_SLAVE 0x10 /* SMBus host address */
-
-/* NAND: socketed, two chipselects, normally 2 GBytes */
-#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NAND_CS 2
-#define CONFIG_SYS_NAND_USE_FLASH_BBT
-#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
-#define CONFIG_SYS_NAND_PAGE_2K
-
-#define CONFIG_SYS_NAND_LARGEPAGE
-#define CONFIG_SYS_NAND_BASE_LIST { 0x02000000, }
-/* socket has two chipselects, nCE0 gated by address BIT(14) */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_SYS_NAND_MAX_CHIPS 2
-
-/* SD/MMC */
-#define CONFIG_MMC
-#define CONFIG_GENERIC_MMC
-#define CONFIG_DAVINCI_MMC
-#define CONFIG_DAVINCI_MMC_SD1
-#define CONFIG_MMC_MBLOCK
-
-#define PINMUX4_USBDRVBUS_BITCLEAR 0x3000
-#define PINMUX4_USBDRVBUS_BITSET 0x2000
-
-/* USB Configuration */
-#define CONFIG_USB_DAVINCI
-#define CONFIG_USB_MUSB_HCD
-
-#ifdef CONFIG_USB_DAVINCI
-#define CONFIG_CMD_USB /* include support for usb */
-#define CONFIG_CMD_STORAGE /* include support for usb */
-#define CONFIG_CMD_FAT /* include support for FAT/storage*/
-#define CONFIG_DOS_PARTITION /* include support for FAT/storage*/
-#endif
-
-#ifdef CONFIG_USB_MUSB_HCD /* include support for usb host */
-#define CONFIG_CMD_USB /* include support for usb cmd */
-#define CONFIG_USB_STORAGE /* MSC class support */
-#define CONFIG_CMD_STORAGE /* inclue support for usb-storage cmd */
-#define CONFIG_CMD_FAT /* inclue support for FAT/storage */
-#define CONFIG_DOS_PARTITION /* inclue support for FAT/storage */
-
-#ifdef CONFIG_USB_KEYBOARD /* HID class support */
-#define CONFIG_SYS_USB_EVENT_POLL
-
-#define CONFIG_PREBOOT "usb start"
-#endif /* CONFIG_USB_KEYBOARD */
-#endif /* CONFIG_USB_MUSB_HCD */
-
-#ifdef CONFIG_USB_MUSB_UDC
-#define CONFIG_USB_DEVICE 1
-#define CONFIG_USB_TTY 1
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV 1
-#define CONFIG_USBD_VENDORID 0x0451
-#define CONFIG_USBD_PRODUCTID 0x5678
-#define CONFIG_USBD_MANUFACTURER "Texas Instruments"
-#define CONFIG_USBD_PRODUCT_NAME "DM365VM"
-#endif /* CONFIG_USB_MUSB_UDC */
-
-/* U-Boot command configuration */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
-#ifdef CONFIG_MMC
-#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_MMC
-#endif
-
-#ifdef CONFIG_NAND_DAVINCI
-#define CONFIG_CMD_MTDPARTS
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_MTD_DEVICE
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_UBI
-#define CONFIG_RBTREE
-#endif
-
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-
-/* U-Boot general configuration */
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE /* Print buffer size */ \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_LONGHELP
-
-#ifdef CONFIG_NAND_DAVINCI
-#define CONFIG_ENV_SIZE (256 << 10) /* 256 KiB */
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_OFFSET 0x3C0000
-#undef CONFIG_ENV_IS_IN_FLASH
-#endif
-
-#if defined(CONFIG_MMC) && !defined(CONFIG_ENV_IS_IN_NAND)
-#define CONFIG_CMD_ENV
-#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
-#define CONFIG_ENV_OFFSET (51 << 9) /* Sector 51 */
-#define CONFIG_ENV_IS_IN_MMC
-#undef CONFIG_ENV_IS_IN_FLASH
-#endif
-
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOTCOMMAND \
- "dhcp;bootm"
-#define CONFIG_BOOTARGS \
- "console=ttyS0,115200n8 " \
- "root=/dev/mmcblk0p1 rootwait rootfstype=ext3 ro"
-
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_TIMESTAMP
-
-/* U-Boot memory configuration */
-#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* 1 MiB */
-#define CONFIG_SYS_MEMTEST_START 0x87000000 /* physical address */
-#define CONFIG_SYS_MEMTEST_END 0x88000000 /* test 16MB RAM */
-
-/* Linux interfacing */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_SYS_BARGSIZE 1024 /* bootarg Size */
-#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* kernel address */
-
-
-/* NAND configuration issocketed with two chipselects just like the DM355 EVM.
- * It normally comes with a 2GByte SLC part with 2KB pages
- * (and 128KB erase blocks); other
- * 2GByte parts may have 4KB pages, 256KB erase blocks, and use MLC. (MLC
- * pretty much demands the 4-bit ECC support.) You can of course swap in
- * other parts, including small page ones.
- */
-#define MTDIDS_DEFAULT "nand0=davinci_nand.0"
-
-#ifdef CONFIG_SYS_NAND_LARGEPAGE
-/* Use same layout for 128K/256K blocks; allow some bad blocks */
-#define PART_BOOT "2m(bootloader)ro,"
-#else
-/* Assume 16K erase blocks; allow a few bad ones. */
-#define PART_BOOT "512k(bootloader)ro,"
-#endif
-
-#define PART_KERNEL "4m(kernel)," /* kernel + initramfs */
-#define PART_REST "-(filesystem)"
-
-#define MTDPARTS_DEFAULT \
- "mtdparts=davinci_nand.0:" PART_BOOT PART_KERNEL PART_REST
-
-#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * Copyright (C) 2009 Texas Instruments Incorporated
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* Spectrum Digital TMS320DM6467 EVM board */
-#define DAVINCI_DM6467EVM
-#define CONFIG_SYS_USE_NAND
-#define CONFIG_SYS_NAND_SMALLPAGE
-
-#define CONFIG_SKIP_LOWLEVEL_INIT
-
-/* SoC Configuration */
-
-/* Clock rates detection */
-#ifndef __ASSEMBLY__
-extern unsigned int davinci_arm_clk_get(void);
-#endif
-
-/* Arm Clock frequency */
-#define CONFIG_SYS_CLK_FREQ davinci_arm_clk_get()
-/* Timer Input clock freq */
-#define CONFIG_SYS_HZ_CLOCK (CONFIG_SYS_CLK_FREQ/2)
-#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
-#define CONFIG_SOC_DM646X
-
-/* EEPROM definitions for EEPROM */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-
-/* Memory Info */
-#define CONFIG_SYS_MALLOC_LEN (1 << 20) /* 1 MiB */
-#define CONFIG_SYS_MEMTEST_START 0x80000000
-#define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */
-#define CONFIG_NR_DRAM_BANKS 1
-#define PHYS_SDRAM_1 0x80000000 /* DDR Start */
-#define PHYS_SDRAM_1_SIZE (256 << 20) /* DDR size 256MB */
-
-/* Linux interfacing */
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_SYS_BARGSIZE 1024 /* Bootarg Size */
-#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* kernel address */
-#define CONFIG_REVISION_TAG
-
-/* Serial Driver info */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 4
-#define CONFIG_SYS_NS16550_COM1 0x01c20000
-#define CONFIG_SYS_NS16550_CLK 24000000
-#define CONFIG_CONS_INDEX 1
-#define CONFIG_BAUDRATE 115200
-
-/* I2C Configuration */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_DAVINCI
-#define CONFIG_SYS_DAVINCI_I2C_SPEED 80000
-#define CONFIG_SYS_DAVINCI_I2C_SLAVE 10
-
-/* Network & Ethernet Configuration */
-#define CONFIG_DRIVER_TI_EMAC
-#define CONFIG_MII
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
-
-/* Flash & Environment */
-#define CONFIG_SYS_NO_FLASH
-#ifdef CONFIG_SYS_USE_NAND
-#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NAND_MASK_CLE 0x80000
-#define CONFIG_SYS_NAND_MASK_ALE 0x40000
-#define CONFIG_SYS_NAND_CS 2
-#undef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
-#define CONFIG_SYS_NAND_BASE_LIST {0x42000000, }
-#define CONFIG_SYS_NAND_HW_ECC
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define CONFIG_ENV_OFFSET 0
-#else
-#define CONFIG_ENV_IS_NOWHERE
-#define CONFIG_ENV_SIZE (4 << 10) /* 4 KiB */
-#endif
-
-/* U-Boot general configuration */
-#define CONFIG_BOOTDELAY 3
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-#define CONFIG_BOOTCOMMAND "source 0x82080000; dhcp; bootm"
-#define CONFIG_BOOTARGS \
- "mem=120M console=ttyS0,115200n8 " \
- "root=/dev/hda1 rw noinitrd ip=dhcp"
-
-/* U-Boot commands */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_DHCP
-#ifdef CONFIG_SYS_USE_NAND
-#define CONFIG_CMD_NAND
-#endif
-
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
-#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * Define this to make U-Boot skip low level initialization when loaded
- * by initial bootloader. Not required by NAND U-Boot version but IS
- * required for a NOR version used to burn the real NOR U-Boot into
- * NOR Flash. NAND and NOR support for DaVinci chips is mutually exclusive
- * so it is NOT possible to build a U-Boot with both NAND and NOR routines.
- * NOR U-Boot is loaded directly from Flash so it must perform all the
- * low level initialization itself. NAND version is loaded by an initial
- * bootloader (UBL in TI-ese) that performs such an initialization so it's
- * skipped in NAND version. The third DaVinci boot mode loads a bootloader
- * via UART0 and that bootloader in turn loads and runs U-Boot (or whatever)
- * performing low level init prior to loading. All that means we can NOT use
- * NAND version to put U-Boot into NOR because it doesn't have NOR support and
- * we can NOT use NOR version because it performs low level initialization
- * effectively destroying itself in DDR memory. That's why a separate NOR
- * version with this define is needed. It is loaded via UART, then one uses
- * it to somehow download a proper NOR version built WITHOUT this define to
- * RAM (tftp?) and burn it to NOR Flash. I would be probably able to squeeze
- * NOR support into the initial bootloader so it won't be needed but DaVinci
- * static RAM might be too small for this (I have something like 2Kbytes left
- * as of now, without NOR support) so this might've not happened...
- *
-#define CONFIG_NOR_UART_BOOT
- */
-
-/*=======*/
-/* Board */
-/*=======*/
-#define DV_EVM
-#define CONFIG_SYS_NAND_SMALLPAGE
-#define CONFIG_SYS_USE_NAND
-/*===================*/
-/* SoC Configuration */
-/*===================*/
-#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
-#define CONFIG_SYS_HZ_CLOCK 27000000 /* Timer Input clock freq */
-#define CONFIG_SOC_DM644X
-/*====================================================*/
-/* EEPROM definitions for Atmel 24C256BN SEEPROM chip */
-/* on Sonata/DV_EVM board. No EEPROM on schmoogie. */
-/*====================================================*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-/*=============*/
-/* Memory Info */
-/*=============*/
-#define CONFIG_SYS_MALLOC_LEN (0x10000 + 128*1024) /* malloc() len */
-#define CONFIG_SYS_MEMTEST_START 0x80000000 /* memtest start address */
-#define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x80000000 /* DDR Start */
-#define PHYS_SDRAM_1_SIZE 0x10000000 /* DDR size 256MB */
-
-#define DDR_8BANKS /* 8-bank DDR2 (256MB) */
-/*====================*/
-/* Serial Driver info */
-/*====================*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size, byteorder */
-#define CONFIG_SYS_NS16550_COM1 0x01c20000 /* Base address of UART0 */
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK /* Input clock to NS16550 */
-#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
-#define CONFIG_BAUDRATE 115200 /* Default baud rate */
-/*===================*/
-/* I2C Configuration */
-/*===================*/
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_DAVINCI
-#define CONFIG_SYS_DAVINCI_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */
-#define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
-/*==================================*/
-/* Network & Ethernet Configuration */
-/*==================================*/
-#define CONFIG_DRIVER_TI_EMAC
-#define CONFIG_MII
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
-/*=====================*/
-/* Flash & Environment */
-/*=====================*/
-#ifdef CONFIG_SYS_USE_NAND
-#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NAND_CS 2
-#undef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
-#ifdef CONFIG_SYS_NAND_SMALLPAGE
-#define CONFIG_ENV_SECT_SIZE 512 /* Env sector Size */
-#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
-#define CONFIG_MTD_PARTITIONS
-#define CONFIG_MTD_DEVICE
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT \
- "nand0=davinci_nand.0"
-#define MTDPARTS_DEFAULT \
- "mtdparts=davinci_nand.0:384k(bootloader)ro,4m(kernel),-(filesystem)"
-#else
-#define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */
-#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
-#endif
-#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SYS_NAND_BASE 0x02000000
-#define CONFIG_SYS_NAND_USE_FLASH_BBT
-#define CONFIG_SYS_NAND_HW_ECC
-#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
-#elif defined(CONFIG_SYS_USE_NOR)
-#ifdef CONFIG_NOR_UART_BOOT
-#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#else
-#undef CONFIG_SKIP_LOWLEVEL_INIT
-#endif
-#define CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_SYS_NO_FLASH
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
-#define CONFIG_SYS_FLASH_SECT_SZ 0x10000 /* 64KB sect size AMD Flash */
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*3)
-#define PHYS_FLASH_1 0x02000000 /* CS2 Base address */
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 /* Flash Base for U-Boot */
-#define PHYS_FLASH_SIZE 0x2000000 /* Flash size 32MB */
-#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
-#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ /* Env sector Size */
-#endif
-/*==============================*/
-/* U-Boot general configuration */
-/*==============================*/
-#define CONFIG_MISC_INIT_R
-#undef CONFIG_BOOTDELAY
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buffer sz */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* default Linux kernel load address */
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-#define CONFIG_USB_MUSB_HCD
-#define CONFIG_USB_DAVINCI
-/*===================*/
-/* Linux Information */
-/*===================*/
-#define LINUX_BOOT_PARAM_ADDR 0x80000100
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTARGS "mem=120M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp"
-#define CONFIG_BOOTCOMMAND "setenv setboot setenv bootargs \\$(bootargs) video=dm64xxfb:output=\\$(videostd);run setboot; bootm 0x2050000"
-/*=================*/
-/* U-Boot commands */
-/*=================*/
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_EEPROM
-
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
-#ifdef CONFIG_SYS_USE_NAND
-#define CONFIG_CMD_NAND
-#elif defined(CONFIG_SYS_USE_NOR)
-#define CONFIG_CMD_JFFS2
-#else
-#error "Either CONFIG_SYS_USE_NAND or CONFIG_SYS_USE_NOR _MUST_ be defined !!!"
-#endif
-/*==========================*/
-/* USB MSC support (if any) */
-/*==========================*/
-#ifdef CONFIG_USB_DAVINCI
-#define CONFIG_CMD_USB
-#ifdef CONFIG_USB_MUSB_HCD
-#define CONFIG_USB_STORAGE
-#define CONFIG_CMD_STORAGE
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-#ifdef CONFIG_USB_KEYBOARD
-#define CONFIG_SYS_USB_EVENT_POLL
-#define CONFIG_PREBOOT "usb start"
-#endif
-#endif
-
-#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*=======*/
-/* Board */
-/*=======*/
-#define SCHMOOGIE
-#define CONFIG_SYS_NAND_LARGEPAGE
-#define CONFIG_SYS_USE_NAND
-#define MACH_TYPE_SCHMOOGIE 1255
-#define CONFIG_MACH_TYPE MACH_TYPE_SCHMOOGIE
-
-/*===================*/
-/* SoC Configuration */
-/*===================*/
-#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
-#define CONFIG_SYS_HZ_CLOCK 27000000 /* Timer Input clock freq */
-#define CONFIG_SOC_DM644X
-/*=============*/
-/* Memory Info */
-/*=============*/
-#define CONFIG_SYS_MALLOC_LEN (0x10000 + 256*1024) /* malloc() len */
-#define CONFIG_SYS_MEMTEST_START 0x80000000 /* memtest start address */
-#define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x80000000 /* DDR Start */
-#define PHYS_SDRAM_1_SIZE 0x08000000 /* DDR size 128MB */
-#define DDR_4BANKS /* 4-bank DDR2 (128MB) */
-/*====================*/
-/* Serial Driver info */
-/*====================*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size, byteorder */
-#define CONFIG_SYS_NS16550_COM1 0x01c20000 /* Base address of UART0 */
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK /* Input clock to NS16550 */
-#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
-#define CONFIG_BAUDRATE 115200 /* Default baud rate */
-/*===================*/
-/* I2C Configuration */
-/*===================*/
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_DAVINCI
-#define CONFIG_SYS_DAVINCI_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */
-#define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
-/*==================================*/
-/* Network & Ethernet Configuration */
-/*==================================*/
-#define CONFIG_DRIVER_TI_EMAC
-#define CONFIG_MII
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-/*=====================*/
-/* Flash & Environment */
-/*=====================*/
-#undef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NAND_CS 2
-#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
-#define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */
-#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SYS_NAND_BASE 0x02000000
-#define CONFIG_SYS_NAND_HW_ECC
-#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
-/*=====================*/
-/* Board related stuff */
-/*=====================*/
-#define CONFIG_RTC_DS1307 /* RTC chip on SCHMOOGIE */
-#define CONFIG_SYS_I2C_RTC_ADDR 0x6f /* RTC chip I2C address */
-#define CONFIG_UID_DS28CM00 /* Unique ID on SCHMOOGIE */
-#define CONFIG_SYS_UID_ADDR 0x50 /* UID chip I2C address */
-/*==============================*/
-/* U-Boot general configuration */
-/*==============================*/
-#define CONFIG_MISC_INIT_R
-#undef CONFIG_BOOTDELAY
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buffer sz */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* default Linux kernel load address */
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-/*===================*/
-/* Linux Information */
-/*===================*/
-#define LINUX_BOOT_PARAM_ADDR 0x80000100
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTARGS "mem=56M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp"
-#define CONFIG_BOOTCOMMAND "setenv setboot setenv bootargs \\$(bootargs) video=dm64xxfb:output=\\$(videostd);run setboot"
-/*=================*/
-/* U-Boot commands */
-/*=================*/
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_NAND
-#undef CONFIG_CMD_EEPROM
-
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
-#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * Copyright (C) 2008 Lyrtech <www.lyrtech.com>
- * Copyright (C) 2008 Philip Balister, OpenSDR <philip@opensdr.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* Board */
-#define SFFSDR
-#define CONFIG_SYS_NAND_LARGEPAGE
-#define CONFIG_SYS_USE_NAND
-#define CONFIG_SYS_USE_DSPLINK /* don't power up the DSP. */
-/* SoC Configuration */
-#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
-#define CONFIG_SYS_HZ_CLOCK 27000000 /* Timer Input clock freq */
-#define CONFIG_SOC_DM644X
-/* EEPROM definitions for Atmel 24LC64 EEPROM chip */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-/* Memory Info */
-#define CONFIG_SYS_MALLOC_LEN (0x10000 + 256*1024) /* malloc() len */
-#define CONFIG_SYS_MEMTEST_START 0x80000000 /* memtest start address */
-#define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x80000000 /* DDR Start */
-#define PHYS_SDRAM_1_SIZE 0x08000000 /* DDR size 128MB */
-#define DDR_4BANKS /* 4-bank DDR2 (128MB) */
-/* Serial Driver info */
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size, byteorder */
-#define CONFIG_SYS_NS16550_COM1 0x01c20000 /* Base address of UART0 */
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK /* Input clock to NS16550 */
-#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
-#define CONFIG_BAUDRATE 115200 /* Default baud rate */
-/* I2C Configuration */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_DAVINCI
-#define CONFIG_SYS_DAVINCI_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */
-#define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
-/* Network & Ethernet Configuration */
-#define CONFIG_DRIVER_TI_EMAC
-#define CONFIG_MII
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
-#define CONFIG_OVERWRITE_ETHADDR_ONCE
-/* Flash & Environment */
-#undef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NAND_CS 2
-#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
-#define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */
-#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SYS_NAND_BASE 0x02000000
-#define CONFIG_SYS_NAND_HW_ECC
-#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
-/* I2C switch definitions for PCA9543 chip */
-#define CONFIG_SYS_I2C_PCA9543_ADDR 0x70
-#define CONFIG_SYS_I2C_PCA9543_ADDR_LEN 0 /* Single register. */
-#define CONFIG_SYS_I2C_PCA9543_ENABLE_CH0 0x01 /* Enable channel 0. */
-/* U-Boot general configuration */
-#define CONFIG_MISC_INIT_R
-#define CONFIG_BOOTDELAY 5 /* Autoboot after 5 seconds. */
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE \
- (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print buffer size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* Default Linux kernel
- * load address. */
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far,
- * may be later */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-/* Linux Information */
-#define LINUX_BOOT_PARAM_ADDR 0x80000100
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTARGS \
- "mem=56M " \
- "console=ttyS0,115200n8 " \
- "root=/dev/nfs rw noinitrd ip=dhcp " \
- "nfsroot=${serverip}:/nfsroot/sffsdr " \
- "eth0=${ethaddr}"
-#define CONFIG_BOOTCOMMAND \
- "nand read 87A00000 100000 300000;" \
- "bootelf 87A00000"
-/* U-Boot commands */
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF /* Needed to load Integrity kernel. */
-
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
-#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
+++ /dev/null
-/*
- * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * Define this to make U-Boot skip low level initialization when loaded
- * by initial bootloader. Not required by NAND U-Boot version but IS
- * required for a NOR version used to burn the real NOR U-Boot into
- * NOR Flash. NAND and NOR support for DaVinci chips is mutually exclusive
- * so it is NOT possible to build a U-Boot with both NAND and NOR routines.
- * NOR U-Boot is loaded directly from Flash so it must perform all the
- * low level initialization itself. NAND version is loaded by an initial
- * bootloader (UBL in TI-ese) that performs such an initialization so it's
- * skipped in NAND version. The third DaVinci boot mode loads a bootloader
- * via UART0 and that bootloader in turn loads and runs U-Boot (or whatever)
- * performing low level init prior to loading. All that means we can NOT use
- * NAND version to put U-Boot into NOR because it doesn't have NOR support and
- * we can NOT use NOR version because it performs low level initialization
- * effectively destroying itself in DDR memory. That's why a separate NOR
- * version with this define is needed. It is loaded via UART, then one uses
- * it to somehow download a proper NOR version built WITHOUT this define to
- * RAM (tftp?) and burn it to NOR Flash. I would be probably able to squeeze
- * NOR support into the initial bootloader so it won't be needed but DaVinci
- * static RAM might be too small for this (I have something like 2Kbytes left
- * as of now, without NOR support) so this might've not happened...
- *
-#define CONFIG_NOR_UART_BOOT
- */
-
-/*=======*/
-/* Board */
-/*=======*/
-#define SONATA_BOARD
-#define CONFIG_SYS_NAND_SMALLPAGE
-#define CONFIG_SYS_USE_NOR
-#define MACH_TYPE_SONATA 1254
-#define CONFIG_MACH_TYPE MACH_TYPE_SONATA
-/*===================*/
-/* SoC Configuration */
-/*===================*/
-#define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */
-#define CONFIG_SYS_HZ_CLOCK 27000000 /* Timer Input clock freq */
-#define CONFIG_SOC_DM644X
-/*====================================================*/
-/* EEPROM definitions for Atmel 24C256BN SEEPROM chip */
-/* on Sonata/DV_EVM board. No EEPROM on schmoogie. */
-/*====================================================*/
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20
-/*=============*/
-/* Memory Info */
-/*=============*/
-#define CONFIG_SYS_MALLOC_LEN (0x10000 + 128*1024) /* malloc() len */
-#define CONFIG_SYS_MEMTEST_START 0x80000000 /* memtest start address */
-#define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */
-#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
-#define PHYS_SDRAM_1 0x80000000 /* DDR Start */
-#define PHYS_SDRAM_1_SIZE 0x08000000 /* DDR size 128MB */
-#define DDR_4BANKS /* 4-bank DDR2 (128MB) */
-/*====================*/
-/* Serial Driver info */
-/*====================*/
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size, byteorder */
-#define CONFIG_SYS_NS16550_COM1 0x01c20000 /* Base address of UART0 */
-#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK /* Input clock to NS16550 */
-#define CONFIG_CONS_INDEX 1 /* use UART0 for console */
-#define CONFIG_BAUDRATE 115200 /* Default baud rate */
-/*===================*/
-/* I2C Configuration */
-/*===================*/
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_DAVINCI
-#define CONFIG_SYS_DAVINCI_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */
-#define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
-/*==================================*/
-/* Network & Ethernet Configuration */
-/*==================================*/
-#define CONFIG_DRIVER_TI_EMAC
-#define CONFIG_MII
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-#define CONFIG_NET_RETRY_COUNT 10
-/*=====================*/
-/* Flash & Environment */
-/*=====================*/
-#ifdef CONFIG_SYS_USE_NAND
-#define CONFIG_NAND_DAVINCI
-#define CONFIG_SYS_NAND_CS 2
-#undef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_ENV_OVERWRITE /* instead if obsoleted forceenv() */
-#define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */
-#define CONFIG_ENV_SECT_SIZE 512 /* Env sector Size */
-#define CONFIG_ENV_SIZE (16 << 10) /* 16 KiB */
-#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#define CONFIG_SYS_NAND_BASE 0x02000000
-#define CONFIG_SYS_NAND_HW_ECC
-#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
-#define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */
-#elif defined(CONFIG_SYS_USE_NOR)
-#ifdef CONFIG_NOR_UART_BOOT
-#define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */
-#else
-#undef CONFIG_SKIP_LOWLEVEL_INIT
-#endif
-#define CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_SYS_NO_FLASH
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */
-#define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* 128KB sect size AMD Flash */
-#define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*2)
-#define CONFIG_ENV_SIZE CONFIG_SYS_FLASH_SECT_SZ
-#define PHYS_FLASH_1 0x02000000 /* CS2 Base address */
-#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 /* Flash Base for U-Boot */
-#define PHYS_FLASH_SIZE 0x2000000 /* Flash size 32MB */
-#define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
-#define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ /* Env sector Size */
-#endif
-/*==============================*/
-/* U-Boot general configuration */
-/*==============================*/
-#define CONFIG_MISC_INIT_R
-#undef CONFIG_BOOTDELAY
-#define CONFIG_BOOTFILE "uImage" /* Boot file name */
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buffer sz */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-#define CONFIG_SYS_LOAD_ADDR 0x80700000 /* default Linux kernel load address */
-#define CONFIG_VERSION_VARIABLE
-#define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_SYS_LONGHELP
-#define CONFIG_CRC32_VERIFY
-#define CONFIG_MX_CYCLIC
-/*===================*/
-/* Linux Information */
-/*===================*/
-#define LINUX_BOOT_PARAM_ADDR 0x80000100
-#define CONFIG_CMDLINE_TAG
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_BOOTARGS "mem=56M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp"
-#define CONFIG_BOOTCOMMAND "setenv setboot setenv bootargs \\$(bootargs) video=dm64xxfb:output=\\$(videostd);run setboot; bootm 0x2060000"
-/*=================*/
-/* U-Boot commands */
-/*=================*/
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SAVES
-#define CONFIG_CMD_EEPROM
-#ifdef CONFIG_SYS_USE_NAND
-#define CONFIG_CMD_NAND
-#elif defined(CONFIG_SYS_USE_NOR)
-#define CONFIG_CMD_JFFS2
-#else
-#error "Either CONFIG_SYS_USE_NAND or CONFIG_SYS_USE_NOR _MUST_ be defined !!!"
-#endif
-
-#ifdef CONFIG_CMD_BDI
-#define CONFIG_CLOCKS
-#endif
-
-#define CONFIG_MAX_RAM_BANK_SIZE (256 << 20) /* 256 MB */
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_SIZE 0x1000
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-#endif /* __CONFIG_H */
projects / project / bcm63xx / u-boot.git / commitdiff