The AP121FE is a slightly modified version of already supported AP121F
model (added to ar71xx in
0c6165d21a and to ath79 in
334bbc5198).
The differences in compare to AP121F:
- no micro SD card reader
- USB data lines are included in Type-A plug
- USB bus switched to device/peripheral mode (permanently, in bootstrap)
Other than that, specifications are the same:
- Atheros AR9331
- 400/400/200 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR1)
- 16 MB of flash (SPI NOR)
- 1x 10/100 Mbps Ethernet
- 1T1R 2.4 GHz Wi-Fi, up to 15 dBm
- 1x IPEX/U.FL connector, internal PCB antenna
- 3x LED, 1x button, 1x switch
- 4-pin UART header on PCB (2 mm pitch)
- USB 2.0 Type-A plug (power and data)
Flash instruction (under U-Boot web recovery mode):
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of all LEDs (indicates network setup), then keep
button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-#include "ar9331.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "ar9331_alfa-network_ap121f.dtsi"
/ {
model = "ALFA Network AP121F";
compatible = "alfa-network,ap121f", "qca,ar9331";
- aliases {
- label-mac-device = &wmac;
- led-boot = &led_vpn;
- led-failsafe = &led_vpn;
- led-upgrade = &led_vpn;
- serial0 = &uart;
- };
-
- keys {
- compatible = "gpio-keys";
-
- reset {
- label = "reset";
- linux,code = <KEY_RESTART>;
- gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
- };
-
- switch {
- label = "switch";
- linux,code = <BTN_0>;
- gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
- };
- };
-
leds {
compatible = "gpio-leds";
};
};
-ð0 {
- status = "okay";
-
- mtd-mac-address = <&art 0x0>;
-
- gmac-config {
- device = <&gmac>;
- switch-phy-addr-swap = <0>;
- switch-phy-swap = <0>;
- };
-};
-
-ð1 {
- status = "okay";
-
- compatible = "syscon", "simple-mfd";
-};
-
-&spi {
- status = "okay";
-
- num-cs = <1>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <50000000>;
- m25p,fast-read;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "u-boot";
- reg = <0x000000 0x030000>;
- read-only;
- };
-
- partition@30000 {
- label = "u-boot-env";
- reg = <0x030000 0x010000>;
- };
-
- art: partition@40000 {
- label = "art";
- reg = <0x040000 0x010000>;
- read-only;
- };
-
- partition@50000 {
- compatible = "denx,uimage";
- label = "firmware";
- reg = <0x050000 0xfb0000>;
- };
- };
- };
-};
-
-&uart {
- status = "okay";
-};
-
&usb {
- status = "okay";
dr_mode = "host";
};
-
-&usb_phy {
- status = "okay";
-};
-
-&wmac {
- status = "okay";
-
- mtd-cal-data = <&art 0x1000>;
-};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9331.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ aliases {
+ label-mac-device = &wmac;
+ led-boot = &led_vpn;
+ led-failsafe = &led_vpn;
+ led-upgrade = &led_vpn;
+ serial0 = &uart;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+
+ switch {
+ label = "switch";
+ linux,code = <BTN_0>;
+ gpios = <&gpio 21 GPIO_ACTIVE_HIGH>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ mtd-mac-address = <&art 0x0>;
+
+ gmac-config {
+ device = <&gmac>;
+ switch-phy-addr-swap = <0>;
+ switch-phy-swap = <0>;
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ compatible = "syscon", "simple-mfd";
+};
+
+&spi {
+ status = "okay";
+
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x030000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "u-boot-env";
+ reg = <0x030000 0x010000>;
+ };
+
+ art: partition@40000 {
+ label = "art";
+ reg = <0x040000 0x010000>;
+ read-only;
+ };
+
+ partition@50000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x050000 0xfb0000>;
+ };
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&usb {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar9331_alfa-network_ap121f.dtsi"
+
+/ {
+ model = "ALFA Network AP121FE";
+ compatible = "alfa-network,ap121fe", "qca,ar9331";
+
+ leds {
+ compatible = "gpio-leds";
+
+ lan {
+ label = "ap121fe:green:lan";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+
+ led_vpn: vpn {
+ label = "ap121fe:green:vpn";
+ gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan {
+ label = "ap121fe:green:wlan";
+ gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+ };
+};
+
+&usb {
+ dr_mode = "peripheral";
+};
ucidef_set_led_switch "wan" "WAN" "$boardname:orange:eth1" "switch0" "0x04"
;;
alfa-network,ap121f|\
+alfa-network,ap121fe|\
avm,fritz450e)
ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
;;
winchannel,wb2000)
ucidef_set_interface_lan "eth0"
;;
+ alfa-network,ap121fe)
+ ucidef_set_interface_lan "eth0 usb0"
+ ;;
avm,fritz4020|\
pcs,cr3000|\
tplink,archer-c58-v1|\
label_mac=$lan_mac
;;
alfa-network,ap121f|\
+ alfa-network,ap121fe|\
engenius,ens202ext-v1)
label_mac=$(mtd_get_mac_binary art 0x1002)
;;
endef
TARGET_DEVICES += alfa-network_ap121f
+define Device/alfa-network_ap121fe
+ SOC := ar9331
+ DEVICE_VENDOR := ALFA Network
+ DEVICE_MODEL := AP121FE
+ DEVICE_PACKAGES := kmod-usb-chipidea2 kmod-usb-gadget-eth -swconfig
+ IMAGE_SIZE := 16064k
+endef
+TARGET_DEVICES += alfa-network_ap121fe
+
define Device/allnet_all-wap02860ac
SOC := qca9558
DEVICE_VENDOR := ALLNET
projects / openwrt / staging / dangole.git / commitdiff