+++ /dev/null
-Add support for the NetusG20 board by Acmesystems srl.
-This board is based on AT91SAM9G20 SoC.
-
-Signed-off-by: Claudio Mignanti <c.mignanti@gmail.com>
----
- MAKEALL | 1 +
- Makefile | 3 +
- arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c | 5 +
- board/acmesystems/netusg20/Makefile | 56 +++++++
- board/acmesystems/netusg20/config.mk | 1 +
- board/acmesystems/netusg20/led.c | 40 +++++
- board/acmesystems/netusg20/netusg20.c | 152 +++++++++++++++++
- board/acmesystems/netusg20/partition.c | 39 +++++
- include/configs/netusg20.h | 181 +++++++++++++++++++++
- 9 files changed, 478 insertions(+), 0 deletions(-)
- create mode 100644 board/acmesystems/netusg20/Makefile
- create mode 100644 board/acmesystems/netusg20/config.mk
- create mode 100644 board/acmesystems/netusg20/led.c
- create mode 100644 board/acmesystems/netusg20/netusg20.c
- create mode 100644 board/acmesystems/netusg20/partition.c
- create mode 100644 include/configs/netusg20.h
-
-diff --git a/MAKEALL b/MAKEALL
-index d6d5f5b..60e36e1 100755
---- a/MAKEALL
-+++ b/MAKEALL
-@@ -684,6 +684,7 @@ LIST_at91=" \
- meesc \
- mp2usb \
- m501sk \
-+ netusg20 \
- otc570 \
- pm9261 \
- pm9263 \
-diff --git a/Makefile b/Makefile
-index 87d5214..b73659f 100644
---- a/Makefile
-+++ b/Makefile
-@@ -2867,6 +2867,9 @@ at91sam9g45ekes_config : unconfig
- fi;
- @$(MKCONFIG) -a at91sam9m10g45ek arm arm926ejs at91sam9m10g45ek atmel at91
-
-+netusg20_config: unconfig
-+ @$(MKCONFIG) $(@:_config=) arm arm926ejs netusg20 acmesystems at91
-+
- otc570_config : unconfig
- @$(MKCONFIG) $(@:_config=) arm arm926ejs otc570 esd at91
-
-diff --git a/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c b/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c
-index 77d49ab..87ec531 100644
---- a/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c
-+++ b/arch/arm/cpu/arm926ejs/at91/at91sam9260_devices.c
-@@ -59,7 +59,12 @@ void at91_serial3_hw_init(void)
- {
- at91_pmc_t *pmc = (at91_pmc_t *) AT91_PMC_BASE;
-
-+#ifdef CONFIG_NETUSG20
-+ /* pull-up active on DRXD*/
-+ at91_set_a_periph(AT91_PIO_PORTB, 14, 1);
-+#else
- at91_set_a_periph(AT91_PIO_PORTB, 14, 0); /* DRXD */
-+#endif
- at91_set_a_periph(AT91_PIO_PORTB, 15, 1); /* DTXD */
- writel(1 << AT91_ID_SYS, &pmc->pcer);
- }
-diff --git a/board/acmesystems/netusg20/Makefile b/board/acmesystems/netusg20/Makefile
-new file mode 100644
-index 0000000..31589fd
---- /dev/null
-+++ b/board/acmesystems/netusg20/Makefile
-@@ -0,0 +1,56 @@
-+#
-+# (C) Copyright 2003-2008
-+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-+#
-+# (C) Copyright 2008
-+# Stelian Pop <stelian.pop@leadtechdesign.com>
-+# Lead Tech Design <www.leadtechdesign.com>
-+#
-+# See file CREDITS for list of people who contributed to this
-+# project.
-+#
-+# This program is free software; you can redistribute it and/or
-+# modify it under the terms of the GNU General Public License as
-+# published by the Free Software Foundation; either version 2 of
-+# the License, or (at your option) any later version.
-+#
-+# This program is distributed in the hope that it will be useful,
-+# but WITHOUT ANY WARRANTY; without even the implied warranty of
-+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+# GNU General Public License for more details.
-+#
-+# You should have received a copy of the GNU General Public License
-+# along with this program; if not, write to the Free Software
-+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-+# MA 02111-1307 USA
-+#
-+
-+include $(TOPDIR)/config.mk
-+
-+LIB = $(obj)lib$(BOARD).a
-+
-+COBJS-y += netusg20.o
-+COBJS-y += led.o
-+COBJS-y += partition.o
-+
-+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
-+OBJS := $(addprefix $(obj),$(COBJS-y))
-+SOBJS := $(addprefix $(obj),$(SOBJS))
-+
-+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
-+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
-+
-+clean:
-+ rm -f $(SOBJS) $(OBJS)
-+
-+distclean: clean
-+ rm -f $(LIB) core *.bak $(obj).depend
-+
-+#########################################################################
-+
-+# defines $(obj).depend target
-+include $(SRCTREE)/rules.mk
-+
-+sinclude $(obj).depend
-+
-+#########################################################################
-diff --git a/board/acmesystems/netusg20/config.mk b/board/acmesystems/netusg20/config.mk
-new file mode 100644
-index 0000000..ff2cfd1
---- /dev/null
-+++ b/board/acmesystems/netusg20/config.mk
-@@ -0,0 +1 @@
-+TEXT_BASE = 0x23f00000
-diff --git a/board/acmesystems/netusg20/led.c b/board/acmesystems/netusg20/led.c
-new file mode 100644
-index 0000000..1016b98
---- /dev/null
-+++ b/board/acmesystems/netusg20/led.c
-@@ -0,0 +1,40 @@
-+/*
-+ * (C) Copyright 2007-2008
-+ * Stelian Pop <stelian.pop@leadtechdesign.com>
-+ * Lead Tech Design <www.leadtechdesign.com>
-+ *
-+ * See file CREDITS for list of people who contributed to this
-+ * project.
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of
-+ * the License, or (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-+ * MA 02111-1307 USA
-+ */
-+
-+#include <common.h>
-+#include <asm/arch/at91sam9260.h>
-+#include <asm/arch/at91_pmc.h>
-+#include <asm/arch/gpio.h>
-+#include <asm/arch/io.h>
-+
-+
-+void coloured_LED_init(void)
-+{
-+ /* Enable clock */
-+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_PIOA);
-+
-+ at91_set_gpio_output(CONFIG_RED_LED, 1);
-+
-+ at91_set_gpio_value(CONFIG_RED_LED, 1);
-+}
-diff --git a/board/acmesystems/netusg20/netusg20.c b/board/acmesystems/netusg20/netusg20.c
-new file mode 100644
-index 0000000..94b4d4c
---- /dev/null
-+++ b/board/acmesystems/netusg20/netusg20.c
-@@ -0,0 +1,152 @@
-+/*
-+ * (C) Copyright 2007-2008
-+ * Stelian Pop <stelian.pop@leadtechdesign.com>
-+ * Lead Tech Design <www.leadtechdesign.com>
-+ *
-+ * (C) Copyright 2010
-+ * Claudio Mignanti <c.mignanti@gmail.com>
-+ *
-+ * See file CREDITS for list of people who contributed to this
-+ * project.
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of
-+ * the License, or (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-+ * MA 02111-1307 USA
-+ */
-+
-+#include <common.h>
-+#include <asm/arch/at91sam9260.h>
-+#include <asm/arch/at91sam9260_matrix.h>
-+#include <asm/arch/at91sam9_smc.h>
-+#include <asm/arch/at91_common.h>
-+#include <asm/arch/at91_pmc.h>
-+#include <asm/arch/at91_rstc.h>
-+#include <asm/arch/gpio.h>
-+#include <asm/arch/io.h>
-+#include <asm/arch/hardware.h>
-+#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
-+#include <net.h>
-+#endif
-+#include <netdev.h>
-+
-+DECLARE_GLOBAL_DATA_PTR;
-+
-+/* ------------------------------------------------------------------------- */
-+/*
-+ * Miscelaneous platform dependent initialisations
-+ */
-+
-+#ifdef CONFIG_MACB
-+static void at91sam9260ek_macb_hw_init(void)
-+{
-+ unsigned long rstc;
-+
-+ /* Enable clock */
-+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9260_ID_EMAC);
-+
-+ /*
-+ * Disable pull-up on:
-+ * RXDV (PA17) => PHY normal mode (not Test mode)
-+ * ERX0 (PA14) => PHY ADDR0
-+ * ERX1 (PA15) => PHY ADDR1
-+ * ERX2 (PA25) => PHY ADDR2
-+ * ERX3 (PA26) => PHY ADDR3
-+ * ECRS (PA28) => PHY ADDR4 => PHYADDR = 0x0
-+ *
-+ * PHY has internal pull-down
-+ */
-+ writel(pin_to_mask(AT91_PIN_PA14) |
-+ pin_to_mask(AT91_PIN_PA15) |
-+ pin_to_mask(AT91_PIN_PA17) |
-+ pin_to_mask(AT91_PIN_PA25) |
-+ pin_to_mask(AT91_PIN_PA26) |
-+ pin_to_mask(AT91_PIN_PA28),
-+ pin_to_controller(AT91_PIN_PA0) + PIO_PUDR);
-+
-+ rstc = at91_sys_read(AT91_RSTC_MR) & AT91_RSTC_ERSTL;
-+
-+ at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
-+
-+ /* Wait for end hardware reset */
-+ while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
-+
-+ /* Restore NRST value */
-+ at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
-+ (rstc) |
-+ AT91_RSTC_URSTEN);
-+
-+ /* Re-enable pull-up */
-+ writel(pin_to_mask(AT91_PIN_PA14) |
-+ pin_to_mask(AT91_PIN_PA15) |
-+ pin_to_mask(AT91_PIN_PA17) |
-+ pin_to_mask(AT91_PIN_PA25) |
-+ pin_to_mask(AT91_PIN_PA26) |
-+ pin_to_mask(AT91_PIN_PA28),
-+ pin_to_controller(AT91_PIN_PA0) + PIO_PUER);
-+
-+ at91_macb_hw_init();
-+}
-+#endif
-+
-+int board_init(void)
-+{
-+ /* Enable Ctrlc */
-+ console_init_f();
-+
-+ gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G20EK;
-+
-+ /* adress of boot parameters */
-+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-+
-+ at91_serial_hw_init();
-+#ifdef CONFIG_HAS_DATAFLASH
-+ at91_spi0_hw_init((1 << 0) | (1 << 1));
-+#endif
-+#ifdef CONFIG_MACB
-+ at91sam9260ek_macb_hw_init();
-+#endif
-+
-+ return 0;
-+}
-+
-+int dram_init(void)
-+{
-+ gd->bd->bi_dram[0].start = PHYS_SDRAM;
-+ gd->bd->bi_dram[0].size = PHYS_SDRAM_SIZE;
-+ return 0;
-+}
-+
-+#ifdef CONFIG_RESET_PHY_R
-+void reset_phy(void)
-+{
-+#ifdef CONFIG_MACB
-+ /*
-+ * Initialize ethernet HW addr prior to starting Linux,
-+ * needed for nfsroot
-+ */
-+ eth_init(gd->bd);
-+#endif
-+}
-+#endif
-+
-+int board_eth_init(bd_t *bis)
-+{
-+ int rc = 0;
-+#ifdef CONFIG_MACB
-+ rc = macb_eth_initialize(0, (void *)AT91SAM9260_BASE_EMAC, 0x00);
-+#endif
-+ return rc;
-+}
-+
-+void show_boot_progress (int val){}
-diff --git a/board/acmesystems/netusg20/partition.c b/board/acmesystems/netusg20/partition.c
-new file mode 100644
-index 0000000..7d79e53
---- /dev/null
-+++ b/board/acmesystems/netusg20/partition.c
-@@ -0,0 +1,39 @@
-+/*
-+ * (C) Copyright 2008
-+ * Ulf Samuelsson <ulf@atmel.com>
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of
-+ * the License, or (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-+ * MA 02111-1307 USA
-+ *
-+ */
-+#include <common.h>
-+#include <config.h>
-+#include <asm/hardware.h>
-+#include <dataflash.h>
-+
-+AT91S_DATAFLASH_INFO dataflash_info[CONFIG_SYS_MAX_DATAFLASH_BANKS];
-+
-+struct dataflash_addr cs[CONFIG_SYS_MAX_DATAFLASH_BANKS] = {
-+ {CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1, 1}
-+};
-+
-+/*define the area offsets*/
-+dataflash_protect_t area_list[NB_DATAFLASH_AREA] = {
-+ {0x00000000, 0x000041FF, FLAG_PROTECT_SET, 0, "Bootstrap"},
-+ {0x00004200, 0x000083FF, FLAG_PROTECT_CLEAR, 0, "Environment"},
-+ {0x00008400, 0x00041FFF, FLAG_PROTECT_SET, 0, "U-Boot"},
-+ {0x00042000, 0x00251FFF, FLAG_PROTECT_CLEAR, 0, "Kernel"},
-+ {0x00252000, 0xFFFFFFFF, FLAG_PROTECT_CLEAR, 0, "FS"},
-+};
-diff --git a/include/configs/netusg20.h b/include/configs/netusg20.h
-new file mode 100644
-index 0000000..99b4f12
---- /dev/null
-+++ b/include/configs/netusg20.h
-@@ -0,0 +1,181 @@
-+/*
-+ * (C) Copyright 2007-2008
-+ * Stelian Pop <stelian.pop@leadtechdesign.com>
-+ * Lead Tech Design <www.leadtechdesign.com>
-+ *
-+ * Configuation settings for the NetusG20 boards.
-+ *
-+ * See file CREDITS for list of people who contributed to this
-+ * project.
-+ *
-+ * This program is free software; you can redistribute it and/or
-+ * modify it under the terms of the GNU General Public License as
-+ * published by the Free Software Foundation; either version 2 of
-+ * the License, or (at your option) any later version.
-+ *
-+ * This program is distributed in the hope that it will be useful,
-+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
-+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-+ * GNU General Public License for more details.
-+ *
-+ * You should have received a copy of the GNU General Public License
-+ * along with this program; if not, write to the Free Software
-+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-+ * MA 02111-1307 USA
-+ */
-+
-+#ifndef __CONFIG_H
-+#define __CONFIG_H
-+
-+#define CONFIG_AT91_LEGACY
-+
-+/* ARM asynchronous clock */
-+#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432 MHz crystal */
-+#define CONFIG_SYS_HZ 1000
-+
-+#define CONFIG_DISPLAY_CPUINFO
-+
-+#define CONFIG_ARM926EJS 1 /* This is an ARM926EJS Core */
-+#define CONFIG_AT91SAM9G20 1 /* It's an Atmel AT91SAM9G20 SoC*/
-+#define CONFIG_NETUSG20 1
-+
-+#define CONFIG_ARCH_CPU_INIT
-+#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
-+
-+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-+#define CONFIG_SETUP_MEMORY_TAGS 1
-+#define CONFIG_INITRD_TAG 1
-+
-+#define CONFIG_SKIP_LOWLEVEL_INIT
-+#define CONFIG_SKIP_RELOCATE_UBOOT
-+
-+/*
-+ * Hardware drivers
-+ */
-+#define CONFIG_AT91_GPIO 1
-+#define CONFIG_ATMEL_USART 1
-+#undef CONFIG_USART0
-+#undef CONFIG_USART1
-+#undef CONFIG_USART2
-+#define CONFIG_USART3 1 /* USART 3 is DBGU */
-+
-+/* LED */
-+#define CONFIG_AT91_LED
-+#define CONFIG_RED_LED AT91_PIN_PA9 /* this is the power led */
-+#define CONFIG_GREEN_LED AT91_PIN_PA6 /* this is the user led */
-+
-+#define CONFIG_BOOTDELAY 3
-+
-+/*
-+ * BOOTP options
-+ */
-+#define CONFIG_BOOTP_BOOTFILESIZE 1
-+#define CONFIG_BOOTP_BOOTPATH 1
-+#define CONFIG_BOOTP_GATEWAY 1
-+#define CONFIG_BOOTP_HOSTNAME 1
-+
-+/*
-+ * Command line configuration.
-+ */
-+#include <config_cmd_default.h>
-+#undef CONFIG_CMD_BDI
-+#undef CONFIG_CMD_FPGA
-+#undef CONFIG_CMD_IMI
-+#undef CONFIG_CMD_IMLS
-+#undef CONFIG_CMD_LOADS
-+#undef CONFIG_CMD_SOURCE
-+
-+#define CONFIG_CMD_PING 1
-+#define CONFIG_CMD_DHCP 1
-+#define CONFIG_CMD_USB 1
-+
-+/* SDRAM */
-+#define CONFIG_NR_DRAM_BANKS 1
-+#define PHYS_SDRAM 0x20000000
-+#define PHYS_SDRAM_SIZE 0x04000000 /* 64 megs */
-+
-+/* DataFlash */
-+#define CONFIG_ATMEL_DATAFLASH_SPI
-+#define CONFIG_HAS_DATAFLASH 1
-+#define CONFIG_SYS_SPI_WRITE_TOUT (5*CONFIG_SYS_HZ)
-+#define CONFIG_SYS_MAX_DATAFLASH_BANKS 1
-+#define CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 0xD0000000 /* CS1 */
-+#define AT91_SPI_CLK 15000000
-+
-+#define DATAFLASH_TCSS (0x22 << 16)
-+#define DATAFLASH_TCHS (0x1 << 24)
-+
-+/* no NAND flash on this board*/
-+#define CONFIG_SYS_NO_FLASH
-+
-+/* Ethernet */
-+#define CONFIG_MACB 1
-+#define CONFIG_RMII 1
-+#define CONFIG_NET_MULTI 1
-+#define CONFIG_NET_RETRY_COUNT 20
-+#define CONFIG_RESET_PHY_R 1
-+
-+/* MMC */
-+#define CONFIG_MMC
-+#define CONFIG_CMD_MMC
-+#define CONFIG_ATMEL_MCI
-+#define CONFIG_CMD_AUTOSCRIPT
-+#define CONFIG_CMD_IMI
-+#define CONFIG_CMD_SOURCE
-+
-+#define MMCI_BASE 0xFFFA8000
-+
-+/* USB */
-+#define CONFIG_USB_ATMEL
-+#define CONFIG_USB_OHCI_NEW 1
-+#define CONFIG_DOS_PARTITION 1
-+#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
-+#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00500000 /* AT91SAM9260_UHP_BASE */
-+#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9260"
-+#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
-+#define CONFIG_USB_STORAGE 1
-+
-+#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
-+
-+#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
-+#define CONFIG_SYS_MEMTEST_END 0x23e00000
-+
-+/* Filesystem */
-+#define CONFIG_CMD_FAT 1
-+#define CONFIG_CMD_EXT2 1
-+
-+/* bootstrap + u-boot + env + linux in dataflash on CS1 */
-+#define CONFIG_ENV_IS_IN_DATAFLASH 1
-+#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + 0x8400)
-+#define CONFIG_ENV_OFFSET 0x4200
-+#define CONFIG_ENV_ADDR (CONFIG_SYS_DATAFLASH_LOGIC_ADDR_CS1 + CONFIG_ENV_OFFSET)
-+#define CONFIG_ENV_SIZE 0x4200
-+#define CONFIG_BOOTCOMMAND "mmc init; sleep 1; " \
-+ "ext2load mmc 0 0x20000000 uImage; " \
-+ "source 0x20000000"
-+#define CONFIG_BOOTARGS "mem=64M console=ttyS0,115200 " \
-+ "root=/dev/mmcblk0p1 rootwait"
-+
-+#define CONFIG_BAUDRATE 115200
-+#define CONFIG_SYS_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 }
-+
-+#define CONFIG_SYS_PROMPT "U-Boot> "
-+#define CONFIG_SYS_CBSIZE 256
-+#define CONFIG_SYS_MAXARGS 16
-+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-+#define CONFIG_SYS_LONGHELP 1
-+#define CONFIG_CMDLINE_EDITING 1
-+
-+/*
-+ * Size of malloc() pool
-+ */
-+#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
-+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* 128 bytes for initial data */
-+
-+#define CONFIG_STACKSIZE (32*1024) /* regular stack */
-+
-+#ifdef CONFIG_USE_IRQ
-+#error CONFIG_USE_IRQ not supported
-+#endif
-+
-+#endif
---
-1.7.0.4
-
-
projects / openwrt / staging / lynxis / omap.git / commitdiff