Device Sleep is a feature as described in AHCI 1.3.1 Technical Proposal.
This feature enables an HBA and SATA storage device to enter the DevSleep
interface state, enabling lower power SATA-based systems.
Aggressive Device Sleep enables the HBA to assert the DEVSLP signal as
soon as there are no commands outstanding to the device and the port
specific Device Sleep idle timer has expired. This enables autonomous
entry into the DevSleep interface state without waiting for software
in power sensitive systems.
This patch enables Aggressive Device Sleep only if both host controller
and device support it.
Tested on AMD reference board together with Device Sleep supported device
sample.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Aaron Lu <aaron.lwe@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
HOST_CAP2_BOH = (1 << 0), /* BIOS/OS handoff supported */
HOST_CAP2_NVMHCI = (1 << 1), /* NVMHCI supported */
HOST_CAP2_APST = (1 << 2), /* Automatic partial to slumber */
+ HOST_CAP2_SDS = (1 << 3), /* Support device sleep */
+ HOST_CAP2_SADM = (1 << 4), /* Support aggressive DevSlp */
+ HOST_CAP2_DESO = (1 << 5), /* DevSlp from slumber only */
/* registers for each SATA port */
PORT_LST_ADDR = 0x00, /* command list DMA addr */
PORT_SCR_ACT = 0x34, /* SATA phy register: SActive */
PORT_SCR_NTF = 0x3c, /* SATA phy register: SNotification */
PORT_FBS = 0x40, /* FIS-based Switching */
+ PORT_DEVSLP = 0x44, /* device sleep */
/* PORT_IRQ_{STAT,MASK} bits */
PORT_IRQ_COLD_PRES = (1 << 31), /* cold presence detect */
PORT_CMD_ICC_PARTIAL = (0x2 << 28), /* Put i/f in partial state */
PORT_CMD_ICC_SLUMBER = (0x6 << 28), /* Put i/f in slumber state */
+ /* PORT_FBS bits */
PORT_FBS_DWE_OFFSET = 16, /* FBS device with error offset */
PORT_FBS_ADO_OFFSET = 12, /* FBS active dev optimization offset */
PORT_FBS_DEV_OFFSET = 8, /* FBS device to issue offset */
PORT_FBS_DEC = (1 << 1), /* FBS device error clear */
PORT_FBS_EN = (1 << 0), /* Enable FBS */
+ /* PORT_DEVSLP bits */
+ PORT_DEVSLP_DM_OFFSET = 25, /* DITO multiplier offset */
+ PORT_DEVSLP_DM_MASK = (0xf << 25), /* DITO multiplier mask */
+ PORT_DEVSLP_DITO_OFFSET = 15, /* DITO offset */
+ PORT_DEVSLP_MDAT_OFFSET = 10, /* Minimum assertion time */
+ PORT_DEVSLP_DETO_OFFSET = 2, /* DevSlp exit timeout */
+ PORT_DEVSLP_DSP = (1 << 1), /* DevSlp present */
+ PORT_DEVSLP_ADSE = (1 << 0), /* Aggressive DevSlp enable */
+
/* hpriv->flags bits */
#define AHCI_HFLAGS(flags) .private_data = (void *)(flags)
#include <scsi/scsi_cmnd.h>
#include <linux/libata.h>
#include "ahci.h"
+#include "libata.h"
static int ahci_skip_host_reset;
int ahci_ignore_sss;
static int ahci_pmp_qc_defer(struct ata_queued_cmd *qc);
static void ahci_freeze(struct ata_port *ap);
static void ahci_thaw(struct ata_port *ap);
+static void ahci_set_aggressive_devslp(struct ata_port *ap, bool sleep);
static void ahci_enable_fbs(struct ata_port *ap);
static void ahci_disable_fbs(struct ata_port *ap);
static void ahci_pmp_attach(struct ata_port *ap);
MODULE_PARM_DESC(ahci_em_messages,
"AHCI Enclosure Management Message control (0 = off, 1 = on)");
+int devslp_idle_timeout = 1000; /* device sleep idle timeout in ms */
+module_param(devslp_idle_timeout, int, 0644);
+MODULE_PARM_DESC(devslp_idle_timeout, "device sleep idle timeout");
+
static void ahci_enable_ahci(void __iomem *mmio)
{
int i;
}
}
+ /* set aggressive device sleep */
+ if ((hpriv->cap2 & HOST_CAP2_SDS) &&
+ (hpriv->cap2 & HOST_CAP2_SADM) &&
+ (link->device->flags & ATA_DFLAG_DEVSLP)) {
+ if (policy == ATA_LPM_MIN_POWER)
+ ahci_set_aggressive_devslp(ap, true);
+ else
+ ahci_set_aggressive_devslp(ap, false);
+ }
+
if (policy == ATA_LPM_MAX_POWER) {
sata_link_scr_lpm(link, policy, false);
ahci_kick_engine(ap);
}
+static void ahci_set_aggressive_devslp(struct ata_port *ap, bool sleep)
+{
+ void __iomem *port_mmio = ahci_port_base(ap);
+ struct ata_device *dev = ap->link.device;
+ u32 devslp, dm, dito, mdat, deto;
+ int rc;
+ unsigned int err_mask;
+
+ devslp = readl(port_mmio + PORT_DEVSLP);
+ if (!(devslp & PORT_DEVSLP_DSP)) {
+ dev_err(ap->host->dev, "port does not support device sleep\n");
+ return;
+ }
+
+ /* disable device sleep */
+ if (!sleep) {
+ if (devslp & PORT_DEVSLP_ADSE) {
+ writel(devslp & ~PORT_DEVSLP_ADSE,
+ port_mmio + PORT_DEVSLP);
+ err_mask = ata_dev_set_feature(dev,
+ SETFEATURES_SATA_DISABLE,
+ SATA_DEVSLP);
+ if (err_mask && err_mask != AC_ERR_DEV)
+ ata_dev_warn(dev, "failed to disable DEVSLP\n");
+ }
+ return;
+ }
+
+ /* device sleep was already enabled */
+ if (devslp & PORT_DEVSLP_ADSE)
+ return;
+
+ /* set DITO, MDAT, DETO and enable DevSlp, need to stop engine first */
+ rc = ahci_stop_engine(ap);
+ if (rc)
+ return;
+
+ dm = (devslp & PORT_DEVSLP_DM_MASK) >> PORT_DEVSLP_DM_OFFSET;
+ dito = devslp_idle_timeout / (dm + 1);
+ if (dito > 0x3ff)
+ dito = 0x3ff;
+
+ /* Use the nominal value 10 ms if the read MDAT is zero,
+ * the nominal value of DETO is 20 ms.
+ */
+ if (dev->sata_settings[ATA_LOG_DEVSLP_VALID] &
+ ATA_LOG_DEVSLP_VALID_MASK) {
+ mdat = dev->sata_settings[ATA_LOG_DEVSLP_MDAT] &
+ ATA_LOG_DEVSLP_MDAT_MASK;
+ if (!mdat)
+ mdat = 10;
+ deto = dev->sata_settings[ATA_LOG_DEVSLP_DETO];
+ if (!deto)
+ deto = 20;
+ } else {
+ mdat = 10;
+ deto = 20;
+ }
+
+ devslp |= ((dito << PORT_DEVSLP_DITO_OFFSET) |
+ (mdat << PORT_DEVSLP_MDAT_OFFSET) |
+ (deto << PORT_DEVSLP_DETO_OFFSET) |
+ PORT_DEVSLP_ADSE);
+ writel(devslp, port_mmio + PORT_DEVSLP);
+
+ ahci_start_engine(ap);
+
+ /* enable device sleep feature for the drive */
+ err_mask = ata_dev_set_feature(dev,
+ SETFEATURES_SATA_ENABLE,
+ SATA_DEVSLP);
+ if (err_mask && err_mask != AC_ERR_DEV)
+ ata_dev_warn(dev, "failed to enable DEVSLP\n");
+}
+
static void ahci_enable_fbs(struct ata_port *ap)
{
struct ahci_port_priv *pp = ap->private_data;
"flags: "
"%s%s%s%s%s%s%s"
"%s%s%s%s%s%s%s"
- "%s%s%s%s%s%s\n"
+ "%s%s%s%s%s%s%s"
+ "%s%s\n"
,
cap & HOST_CAP_64 ? "64bit " : "",
cap & HOST_CAP_CCC ? "ccc " : "",
cap & HOST_CAP_EMS ? "ems " : "",
cap & HOST_CAP_SXS ? "sxs " : "",
+ cap2 & HOST_CAP2_DESO ? "deso " : "",
+ cap2 & HOST_CAP2_SADM ? "sadm " : "",
+ cap2 & HOST_CAP2_SDS ? "sds " : "",
cap2 & HOST_CAP2_APST ? "apst " : "",
cap2 & HOST_CAP2_NVMHCI ? "nvmp " : "",
cap2 & HOST_CAP2_BOH ? "boh " : ""
int print_info = ehc->i.flags & ATA_EHI_PRINTINFO;
const u16 *id = dev->id;
unsigned long xfer_mask;
+ unsigned int err_mask;
char revbuf[7]; /* XYZ-99\0 */
char fwrevbuf[ATA_ID_FW_REV_LEN+1];
char modelbuf[ATA_ID_PROD_LEN+1];
}
}
+ /* check and mark DevSlp capability */
+ if (ata_id_has_devslp(dev->id))
+ dev->flags |= ATA_DFLAG_DEVSLP;
+
+ /* Obtain SATA Settings page from Identify Device Data Log,
+ * which contains DevSlp timing variables etc.
+ * Exclude old devices with ata_id_has_ncq()
+ */
+ if (ata_id_has_ncq(dev->id)) {
+ err_mask = ata_read_log_page(dev,
+ ATA_LOG_SATA_ID_DEV_DATA,
+ ATA_LOG_SATA_SETTINGS,
+ dev->sata_settings,
+ 1);
+ if (err_mask)
+ ata_dev_dbg(dev,
+ "failed to get Identify Device Data, Emask 0x%x\n",
+ err_mask);
+ }
+
dev->cdb_len = 16;
}
(ap->flags & ATA_FLAG_AN) && ata_id_has_atapi_AN(id) &&
(!sata_pmp_attached(ap) ||
sata_scr_read(&ap->link, SCR_NOTIFICATION, &sntf) == 0)) {
- unsigned int err_mask;
-
/* issue SET feature command to turn this on */
err_mask = ata_dev_set_feature(dev,
SETFEATURES_SATA_ENABLE, SATA_AN);
switch (policy) {
case ATA_LPM_MAX_POWER:
/* disable all LPM transitions */
- scontrol |= (0x3 << 8);
+ scontrol |= (0x7 << 8);
/* initiate transition to active state */
if (spm_wakeup) {
scontrol |= (0x4 << 12);
case ATA_LPM_MED_POWER:
/* allow LPM to PARTIAL */
scontrol &= ~(0x1 << 8);
- scontrol |= (0x2 << 8);
+ scontrol |= (0x6 << 8);
break;
case ATA_LPM_MIN_POWER:
if (ata_link_nr_enabled(link) > 0)
/* no restrictions on LPM transitions */
- scontrol &= ~(0x3 << 8);
+ scontrol &= ~(0x7 << 8);
else {
/* empty port, power off */
scontrol &= ~0xf;
/**
* ata_read_log_page - read a specific log page
* @dev: target device
+ * @log: log to read
* @page: page to read
* @buf: buffer to store read page
* @sectors: number of sectors to read
* RETURNS:
* 0 on success, AC_ERR_* mask otherwise.
*/
-static unsigned int ata_read_log_page(struct ata_device *dev,
- u8 page, void *buf, unsigned int sectors)
+unsigned int ata_read_log_page(struct ata_device *dev, u8 log,
+ u8 page, void *buf, unsigned int sectors)
{
struct ata_taskfile tf;
unsigned int err_mask;
- DPRINTK("read log page - page %d\n", page);
+ DPRINTK("read log page - log 0x%x, page 0x%x\n", log, page);
ata_tf_init(dev, &tf);
tf.command = ATA_CMD_READ_LOG_EXT;
- tf.lbal = page;
+ tf.lbal = log;
+ tf.lbam = page;
tf.nsect = sectors;
tf.hob_nsect = sectors >> 8;
tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_LBA48 | ATA_TFLAG_DEVICE;
u8 csum;
int i;
- err_mask = ata_read_log_page(dev, ATA_LOG_SATA_NCQ, buf, 1);
+ err_mask = ata_read_log_page(dev, ATA_LOG_SATA_NCQ, 0, buf, 1);
if (err_mask)
return -EIO;
unsigned int action);
extern void ata_eh_done(struct ata_link *link, struct ata_device *dev,
unsigned int action);
+extern unsigned int ata_read_log_page(struct ata_device *dev, u8 log,
+ u8 page, void *buf, unsigned int sectors);
extern void ata_eh_autopsy(struct ata_port *ap);
const char *ata_get_cmd_descript(u8 command);
extern void ata_eh_report(struct ata_port *ap);
/* READ_LOG_EXT pages */
ATA_LOG_SATA_NCQ = 0x10,
+ ATA_LOG_SATA_ID_DEV_DATA = 0x30,
+ ATA_LOG_SATA_SETTINGS = 0x08,
+ ATA_LOG_DEVSLP_MDAT = 0x30,
+ ATA_LOG_DEVSLP_MDAT_MASK = 0x1F,
+ ATA_LOG_DEVSLP_DETO = 0x31,
+ ATA_LOG_DEVSLP_VALID = 0x37,
+ ATA_LOG_DEVSLP_VALID_MASK = 0x80,
/* READ/WRITE LONG (obsolete) */
ATA_CMD_READ_LONG = 0x22,
SATA_FPDMA_IN_ORDER = 0x04, /* FPDMA in-order data delivery */
SATA_AN = 0x05, /* Asynchronous Notification */
SATA_SSP = 0x06, /* Software Settings Preservation */
+ SATA_DEVSLP = 0x09, /* Device Sleep */
/* feature values for SET_MAX */
ATA_SET_MAX_ADDR = 0x00,
#define ata_id_cdb_intr(id) (((id)[ATA_ID_CONFIG] & 0x60) == 0x20)
#define ata_id_has_da(id) ((id)[ATA_ID_SATA_CAPABILITY_2] & (1 << 4))
+#define ata_id_has_devslp(id) ((id)[ATA_ID_FEATURE_SUPP] & (1 << 8))
static inline bool ata_id_has_hipm(const u16 *id)
{
ATA_DFLAG_DETACHED = (1 << 25),
ATA_DFLAG_DA = (1 << 26), /* device supports Device Attention */
+ ATA_DFLAG_DEVSLP = (1 << 27), /* device supports Device Sleep */
ATA_DEV_UNKNOWN = 0, /* unknown device */
ATA_DEV_ATA = 1, /* ATA device */
u32 gscr[SATA_PMP_GSCR_DWORDS]; /* PMP GSCR block */
};
+ /* Identify Device Data Log (30h), SATA Settings (page 08h) */
+ u8 sata_settings[ATA_SECT_SIZE];
+
/* error history */
int spdn_cnt;
/* ering is CLEAR_END, read comment above CLEAR_END */
projects / openwrt / staging / blogic.git / commitdiff