FEATURES:=gpio ramdisk rtc squashfs
DEVICE_TYPE:=nas
-KERNEL_PATCHVER:=5.10
-KERNEL_TESTING_PATCHVER:=5.15
+KERNEL_PATCHVER:=5.15
include $(INCLUDE_DIR)/target.mk
+++ /dev/null
-CONFIG_ALIGNMENT_TRAP=y
-CONFIG_ARCH_32BIT_OFF_T=y
-CONFIG_ARCH_CLOCKSOURCE_DATA=y
-CONFIG_ARCH_HAS_BINFMT_FLAT=y
-CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y
-CONFIG_ARCH_HAS_DMA_WRITE_COMBINE=y
-CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
-CONFIG_ARCH_HAS_FORTIFY_SOURCE=y
-CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
-CONFIG_ARCH_HAS_KCOV=y
-CONFIG_ARCH_HAS_KEEPINITRD=y
-CONFIG_ARCH_HAS_MEMBARRIER_SYNC_CORE=y
-CONFIG_ARCH_HAS_PHYS_TO_DMA=y
-CONFIG_ARCH_HAS_RESET_CONTROLLER=y
-CONFIG_ARCH_HAS_SETUP_DMA_OPS=y
-CONFIG_ARCH_HAS_SET_MEMORY=y
-CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y
-CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y
-CONFIG_ARCH_HAS_TEARDOWN_DMA_OPS=y
-CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
-CONFIG_ARCH_HIBERNATION_POSSIBLE=y
-CONFIG_ARCH_KEEP_MEMBLOCK=y
-CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
-CONFIG_ARCH_MULTIPLATFORM=y
-CONFIG_ARCH_MULTI_CPU_AUTO=y
-# CONFIG_ARCH_MULTI_V4 is not set
-# CONFIG_ARCH_MULTI_V4T is not set
-CONFIG_ARCH_MULTI_V4_V5=y
-CONFIG_ARCH_MULTI_V5=y
-CONFIG_ARCH_NR_GPIO=0
-CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
-CONFIG_ARCH_OXNAS=y
-CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
-CONFIG_ARCH_SUPPORTS_UPROBES=y
-CONFIG_ARCH_SUSPEND_POSSIBLE=y
-CONFIG_ARCH_USE_BUILTIN_BSWAP=y
-CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
-CONFIG_ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT=y
-CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
-CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
-CONFIG_ARCH_WANT_LIBATA_LEDS=y
-CONFIG_ARM=y
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_ARM_ATAG_DTB_COMPAT=y
-# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is not set
-# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER is not set
-CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE=y
-CONFIG_ARM_CPU_SUSPEND=y
-CONFIG_ARM_HAS_SG_CHAIN=y
-CONFIG_ARM_L1_CACHE_SHIFT=5
-CONFIG_ARM_PATCH_PHYS_VIRT=y
-CONFIG_ARM_PMU=y
-# CONFIG_ARM_SMMU is not set
-CONFIG_ARM_THUMB=y
-CONFIG_ARM_UNWIND=y
-CONFIG_ATAGS=y
-CONFIG_AUTO_ZRELADDR=y
-CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y
-CONFIG_BLK_CMDLINE_PARSER=y
-CONFIG_BLK_DEBUG_FS=y
-CONFIG_BLK_DEV_BSG=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_COUNT=16
-CONFIG_BLK_DEV_RAM_SIZE=65536
-CONFIG_BLK_PM=y
-CONFIG_BLK_SCSI_REQUEST=y
-CONFIG_CC_HAS_KASAN_GENERIC=y
-CONFIG_CLKDEV_LOOKUP=y
-CONFIG_CLKSRC_MMIO=y
-CONFIG_CLONE_BACKWARDS=y
-CONFIG_CMA=y
-CONFIG_CMA_ALIGNMENT=8
-CONFIG_CMA_AREAS=7
-# CONFIG_CMA_DEBUG is not set
-# CONFIG_CMA_DEBUGFS is not set
-CONFIG_CMA_SIZE_MBYTES=64
-# CONFIG_CMA_SIZE_SEL_MAX is not set
-CONFIG_CMA_SIZE_SEL_MBYTES=y
-# CONFIG_CMA_SIZE_SEL_MIN is not set
-# CONFIG_CMA_SIZE_SEL_PERCENTAGE is not set
-CONFIG_CMDLINE_PARTITION=y
-CONFIG_COMMON_CLK=y
-CONFIG_COMMON_CLK_OXNAS=y
-CONFIG_COMPAT_32BIT_TIME=y
-CONFIG_CONTIG_ALLOC=y
-CONFIG_COREDUMP=y
-CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS=y
-CONFIG_CPU_32v5=y
-CONFIG_CPU_ABRT_EV5TJ=y
-CONFIG_CPU_ARM926T=y
-# CONFIG_CPU_CACHE_ROUND_ROBIN is not set
-CONFIG_CPU_CACHE_VIVT=y
-CONFIG_CPU_COPY_V4WB=y
-CONFIG_CPU_CP15=y
-CONFIG_CPU_CP15_MMU=y
-# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
-# CONFIG_CPU_ICACHE_DISABLE is not set
-CONFIG_CPU_PABRT_LEGACY=y
-CONFIG_CPU_PM=y
-CONFIG_CPU_THUMB_CAPABLE=y
-CONFIG_CPU_TLB_V4WBI=y
-CONFIG_CPU_USE_DOMAINS=y
-CONFIG_CRASH_CORE=y
-CONFIG_CRC16=y
-# CONFIG_CRC32_SARWATE is not set
-CONFIG_CRC32_SLICEBY8=y
-CONFIG_CROSS_MEMORY_ATTACH=y
-CONFIG_CRYPTO_BLAKE2S=y
-CONFIG_CRYPTO_LIB_BLAKE2S_GENERIC=y
-CONFIG_CRYPTO_RNG2=y
-CONFIG_DEBUG_ALIGN_RODATA=y
-CONFIG_DEBUG_BUGVERBOSE=y
-CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
-# CONFIG_DEBUG_USER is not set
-CONFIG_DECOMPRESS_BZIP2=y
-CONFIG_DECOMPRESS_GZIP=y
-CONFIG_DECOMPRESS_LZ4=y
-CONFIG_DECOMPRESS_LZMA=y
-CONFIG_DECOMPRESS_LZO=y
-CONFIG_DECOMPRESS_XZ=y
-CONFIG_DMA_CMA=y
-CONFIG_DMA_REMAP=y
-CONFIG_DNOTIFY=y
-CONFIG_DTC=y
-# CONFIG_DWMAC_DWC_QOS_ETH is not set
-CONFIG_DWMAC_GENERIC=y
-CONFIG_DWMAC_OXNAS=y
-CONFIG_EDAC_ATOMIC_SCRUB=y
-CONFIG_EDAC_SUPPORT=y
-CONFIG_ELF_CORE=y
-CONFIG_FAT_FS=y
-CONFIG_FIXED_PHY=y
-CONFIG_FIX_EARLYCON_MEM=y
-CONFIG_FREEZER=y
-# CONFIG_FW_CACHE is not set
-CONFIG_FW_LOADER_PAGED_BUF=y
-CONFIG_GENERIC_ALLOCATOR=y
-CONFIG_GENERIC_ATOMIC64=y
-CONFIG_GENERIC_BUG=y
-CONFIG_GENERIC_CLOCKEVENTS=y
-CONFIG_GENERIC_CPU_AUTOPROBE=y
-CONFIG_GENERIC_EARLY_IOREMAP=y
-CONFIG_GENERIC_IDLE_POLL_SETUP=y
-CONFIG_GENERIC_IRQ_MULTI_HANDLER=y
-CONFIG_GENERIC_IRQ_SHOW=y
-CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
-CONFIG_GENERIC_PCI_IOMAP=y
-CONFIG_GENERIC_PHY=y
-CONFIG_GENERIC_PINCONF=y
-CONFIG_GENERIC_SCHED_CLOCK=y
-CONFIG_GENERIC_SMP_IDLE_THREAD=y
-CONFIG_GENERIC_STRNCPY_FROM_USER=y
-CONFIG_GENERIC_STRNLEN_USER=y
-CONFIG_GPIOLIB_IRQCHIP=y
-CONFIG_GPIO_GENERIC=y
-CONFIG_GPIO_GENERIC_PLATFORM=y
-CONFIG_HANDLE_DOMAIN_IRQ=y
-CONFIG_HARDIRQS_SW_RESEND=y
-CONFIG_HAS_DMA=y
-CONFIG_HAS_IOMEM=y
-CONFIG_HAS_IOPORT_MAP=y
-CONFIG_HAVE_ARCH_AUDITSYSCALL=y
-CONFIG_HAVE_ARCH_JUMP_LABEL=y
-CONFIG_HAVE_ARCH_KGDB=y
-CONFIG_HAVE_ARCH_PFN_VALID=y
-CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
-CONFIG_HAVE_ARCH_THREAD_STRUCT_WHITELIST=y
-CONFIG_HAVE_ARCH_TRACEHOOK=y
-CONFIG_HAVE_CLK=y
-CONFIG_HAVE_CLK_PREPARE=y
-CONFIG_HAVE_CONTEXT_TRACKING=y
-CONFIG_HAVE_COPY_THREAD_TLS=y
-CONFIG_HAVE_C_RECORDMCOUNT=y
-CONFIG_HAVE_DEBUG_KMEMLEAK=y
-CONFIG_HAVE_DMA_CONTIGUOUS=y
-CONFIG_HAVE_DYNAMIC_FTRACE=y
-CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y
-CONFIG_HAVE_EBPF_JIT=y
-CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
-CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
-CONFIG_HAVE_FUNCTION_TRACER=y
-CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
-CONFIG_HAVE_LD_DEAD_CODE_DATA_ELIMINATION=y
-CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
-CONFIG_HAVE_NET_DSA=y
-CONFIG_HAVE_OPROFILE=y
-CONFIG_HAVE_OPTPROBES=y
-CONFIG_HAVE_PCI=y
-CONFIG_HAVE_PERF_EVENTS=y
-CONFIG_HAVE_PERF_REGS=y
-CONFIG_HAVE_PERF_USER_STACK_DUMP=y
-CONFIG_HAVE_PROC_CPU=y
-CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
-CONFIG_HAVE_RSEQ=y
-CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
-CONFIG_HAVE_UID16=y
-CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
-CONFIG_HID=y
-CONFIG_HID_GENERIC=y
-CONFIG_HWMON=y
-CONFIG_HZ_FIXED=0
-CONFIG_ICPLUS_PHY=y
-CONFIG_INET_DIAG=y
-# CONFIG_INET_DIAG_DESTROY is not set
-# CONFIG_INET_RAW_DIAG is not set
-CONFIG_INET_TCP_DIAG=y
-CONFIG_INITRAMFS_SOURCE=""
-CONFIG_INPUT=y
-# CONFIG_IOMMU_DEBUGFS is not set
-# CONFIG_IOMMU_IO_PGTABLE_ARMV7S is not set
-# CONFIG_IOMMU_IO_PGTABLE_LPAE is not set
-CONFIG_IOMMU_SUPPORT=y
-CONFIG_IRQCHIP=y
-CONFIG_IRQ_DOMAIN=y
-CONFIG_IRQ_FORCED_THREADING=y
-CONFIG_IRQ_WORK=y
-# CONFIG_ISDN is not set
-# CONFIG_JFFS2_FS is not set
-CONFIG_KALLSYMS=y
-CONFIG_KERNEL_GZIP=y
-# CONFIG_KERNEL_XZ is not set
-CONFIG_KEXEC=y
-CONFIG_KEXEC_CORE=y
-# CONFIG_LEDS_BRIGHTNESS_HW_CHANGED is not set
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGER_CPU=y
-CONFIG_LEDS_TRIGGER_GPIO=y
-CONFIG_LEDS_TRIGGER_ONESHOT=y
-CONFIG_LIBFDT=y
-CONFIG_LOCALVERSION_AUTO=y
-CONFIG_LOCK_DEBUGGING_SUPPORT=y
-CONFIG_LZ4_DECOMPRESS=y
-CONFIG_LZO_DECOMPRESS=y
-# CONFIG_MACH_OX810SE is not set
-CONFIG_MDIO_BUS=y
-CONFIG_MDIO_DEVICE=y
-CONFIG_MEMFD_CREATE=y
-CONFIG_MEMORY_ISOLATION=y
-CONFIG_MFD_SYSCON=y
-CONFIG_MIGRATION=y
-CONFIG_MODULES_TREE_LOOKUP=y
-CONFIG_MODULES_USE_ELF_REL=y
-CONFIG_NEED_DMA_MAP_STATE=y
-CONFIG_NEED_KUSER_HELPERS=y
-CONFIG_NEED_PER_CPU_KM=y
-CONFIG_NET_PTP_CLASSIFY=y
-CONFIG_NLS=y
-CONFIG_NO_HZ=y
-CONFIG_NO_HZ_COMMON=y
-CONFIG_NO_HZ_IDLE=y
-CONFIG_OF=y
-CONFIG_OF_ADDRESS=y
-CONFIG_OF_EARLY_FLATTREE=y
-CONFIG_OF_FLATTREE=y
-CONFIG_OF_GPIO=y
-CONFIG_OF_IRQ=y
-CONFIG_OF_KOBJ=y
-CONFIG_OF_MDIO=y
-CONFIG_OF_NET=y
-CONFIG_OLD_SIGACTION=y
-CONFIG_OLD_SIGSUSPEND3=y
-CONFIG_OXNAS_RPS_TIMER=y
-CONFIG_PAGE_OFFSET=0xC0000000
-CONFIG_PAGE_POOL=y
-# CONFIG_PANIC_ON_OOPS is not set
-CONFIG_PANIC_ON_OOPS_VALUE=0
-CONFIG_PANIC_TIMEOUT=0
-CONFIG_PERF_USE_VMALLOC=y
-CONFIG_PGTABLE_LEVELS=2
-CONFIG_PHYLIB=y
-CONFIG_PHYLINK=y
-CONFIG_PHY_OXNAS=y
-CONFIG_PINCTRL=y
-CONFIG_PINCTRL_OXNAS=y
-# CONFIG_PINCTRL_SINGLE is not set
-CONFIG_PM=y
-CONFIG_PM_CLK=y
-# CONFIG_PM_DEBUG is not set
-CONFIG_PM_SLEEP=y
-CONFIG_POWER_RESET=y
-CONFIG_POWER_RESET_OXNAS=y
-CONFIG_PPS=y
-CONFIG_PTP_1588_CLOCK=y
-CONFIG_RAS=y
-CONFIG_RATIONAL=y
-CONFIG_RCU_TRACE=y
-CONFIG_RD_BZIP2=y
-CONFIG_RD_GZIP=y
-CONFIG_RD_LZ4=y
-CONFIG_RD_LZMA=y
-CONFIG_RD_LZO=y
-CONFIG_RD_XZ=y
-CONFIG_REALTEK_PHY=y
-CONFIG_REFCOUNT_FULL=y
-CONFIG_REGMAP=y
-CONFIG_REGMAP_MMIO=y
-CONFIG_RESET_CONTROLLER=y
-CONFIG_RESET_OXNAS=y
-CONFIG_SCHED_DEBUG=y
-CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
-CONFIG_SERIAL_8250_FSL=y
-CONFIG_SERIAL_8250_NR_UARTS=4
-CONFIG_SERIAL_8250_RUNTIME_UARTS=4
-CONFIG_SERIAL_MCTRL_GPIO=y
-CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SERIO=y
-CONFIG_SERIO_LIBPS2=y
-CONFIG_SERIO_SERPORT=y
-CONFIG_SIMPLE_PM_BUS=y
-CONFIG_SLUB_DEBUG=y
-CONFIG_SOCK_DIAG=y
-CONFIG_SPARSE_IRQ=y
-CONFIG_SPLIT_PTLOCK_CPUS=999999
-CONFIG_SRCU=y
-CONFIG_STACKTRACE=y
-CONFIG_STMMAC_ETH=y
-CONFIG_STMMAC_PLATFORM=y
-# CONFIG_STMMAC_SELFTESTS is not set
-# CONFIG_STRIP_ASM_SYMS is not set
-CONFIG_SUSPEND=y
-CONFIG_SUSPEND_FREEZER=y
-CONFIG_SWPHY=y
-CONFIG_SYS_SUPPORTS_APM_EMULATION=y
-CONFIG_THERMAL=y
-CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
-CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
-CONFIG_THERMAL_GOV_STEP_WISE=y
-CONFIG_THERMAL_HWMON=y
-CONFIG_THERMAL_OF=y
-CONFIG_TICK_CPU_ACCOUNTING=y
-CONFIG_TIMER_OF=y
-CONFIG_TIMER_PROBE=y
-CONFIG_TINY_SRCU=y
-CONFIG_TRACE_CLOCK=y
-CONFIG_UEVENT_HELPER_PATH=""
-CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
-CONFIG_UNWINDER_ARM=y
-# CONFIG_UNWINDER_FRAME_POINTER is not set
-CONFIG_USB_SUPPORT=y
-CONFIG_USE_OF=y
-CONFIG_VERSATILE_FPGA_IRQ=y
-CONFIG_VERSATILE_FPGA_IRQ_NR=4
-CONFIG_VFAT_FS=y
-# CONFIG_VFP is not set
-CONFIG_VM_EVENT_COUNTERS=y
-# CONFIG_WATCHDOG is not set
-# CONFIG_WQ_POWER_EFFICIENT_DEFAULT is not set
-CONFIG_XZ_DEC_ARM=y
-CONFIG_XZ_DEC_BCJ=y
-CONFIG_XZ_DEC_IA64=y
-CONFIG_XZ_DEC_POWERPC=y
-CONFIG_XZ_DEC_SPARC=y
-CONFIG_XZ_DEC_X86=y
-CONFIG_ZBOOT_ROM_BSS=0
-CONFIG_ZBOOT_ROM_TEXT=0
-CONFIG_ZLIB_INFLATE=y
.can_queue = SATA_OXNAS_QUEUE_DEPTH,
.sg_tablesize = SATA_OXNAS_MAX_PRD,
.dma_boundary = ATA_DMA_BOUNDARY,
-#if LINUX_VERSION_CODE < KERNEL_VERSION(5, 13, 0)
- .unchecked_isa_dma = 0,
-#endif
};
+++ /dev/null
-- add compatible string
-- add console to bootargs
-- add led aliases
-- adjust nand partition table
----
---- a/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts
-+++ b/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts
-@@ -11,10 +11,10 @@
- / {
- model = "Cloud Engines PogoPlug Series 3";
-
-- compatible = "cloudengines,pogoplugv3", "oxsemi,ox820";
-+ compatible = "cloudengines,pogoplug-series-3", "cloudengines,pogoplugv3", "oxsemi,ox820";
-
- chosen {
-- bootargs = "earlyprintk";
-+ bootargs = "earlyprintk console=ttyS0,115200";
- stdout-path = "serial0:115200n8";
- };
-
-@@ -27,24 +27,28 @@
- serial0 = &uart0;
- gpio0 = &gpio0;
- gpio1 = &gpio1;
-+ led-boot = &led_status;
-+ led-failsafe = &led_warn;
-+ led-running = &led_act;
-+ led-upgrade = &led_warn;
- };
-
- leds {
- compatible = "gpio-leds";
-
-- blue {
-+ led_status: blue {
- label = "pogoplug:blue";
- gpios = <&gpio0 2 0>;
- default-state = "keep";
- };
-
-- orange {
-+ led_warn: orange {
- label = "pogoplug:orange";
- gpios = <&gpio1 16 1>;
- default-state = "keep";
- };
-
-- green {
-+ led_act: green {
- label = "pogoplug:green";
- gpios = <&gpio1 17 1>;
- default-state = "keep";
-@@ -73,11 +77,27 @@
- nand-ecc-algo = "hamming";
-
- partition@0 {
-- label = "boot";
-- reg = <0x00000000 0x00e00000>;
-+ label = "stage1";
-+ reg = <0x00000000 0x00040000>;
- read-only;
- };
-
-+ partition@40000 {
-+ label = "u-boot";
-+ reg = <0x00040000 0x00380000>;
-+ read-only;
-+ };
-+
-+ partition@3c0000 {
-+ label = "u-boot-env";
-+ reg = <0x003c0000 0x00080000>;
-+ };
-+
-+ partition@440000 {
-+ label = "kernel";
-+ reg = <0x00440000 0x009c0000>;
-+ };
-+
- partition@e00000 {
- label = "ubi";
- reg = <0x00e00000 0x07200000>;
+++ /dev/null
-From 552ed4955c1fee1109bf5ba137dc35a411a1448c Mon Sep 17 00:00:00 2001
-From: Daniel Golle <daniel@makrotopia.org>
-Date: Fri, 1 Jun 2018 02:41:15 +0200
-Subject: [PATCH] arm: ox820: remove left-overs
-
-Signed-off-by: Daniel Golle <daniel@makrotopia.org>
----
- drivers/clk/clk-oxnas.c | 2 --
- include/dt-bindings/clock/oxsemi,ox820.h | 32 +++++++++++-------------
- 2 files changed, 14 insertions(+), 20 deletions(-)
-
---- a/drivers/clk/clk-oxnas.c
-+++ b/drivers/clk/clk-oxnas.c
-@@ -29,8 +29,6 @@ struct oxnas_stdclk_data {
- struct clk_hw_onecell_data *onecell_data;
- struct clk_oxnas_gate **gates;
- unsigned int ngates;
-- struct clk_oxnas_pll **plls;
-- unsigned int nplls;
- };
-
- /* Regmap offsets */
---- a/include/dt-bindings/clock/oxsemi,ox820.h
-+++ b/include/dt-bindings/clock/oxsemi,ox820.h
-@@ -6,24 +6,20 @@
- #ifndef DT_CLOCK_OXSEMI_OX820_H
- #define DT_CLOCK_OXSEMI_OX820_H
-
--/* PLLs */
--#define CLK_820_PLLA 0
--#define CLK_820_PLLB 1
--
- /* Gate Clocks */
--#define CLK_820_LEON 2
--#define CLK_820_DMA_SGDMA 3
--#define CLK_820_CIPHER 4
--#define CLK_820_SD 5
--#define CLK_820_SATA 6
--#define CLK_820_AUDIO 7
--#define CLK_820_USBMPH 8
--#define CLK_820_ETHA 9
--#define CLK_820_PCIEA 10
--#define CLK_820_NAND 11
--#define CLK_820_PCIEB 12
--#define CLK_820_ETHB 13
--#define CLK_820_REF600 14
--#define CLK_820_USBDEV 15
-+#define CLK_820_LEON 0
-+#define CLK_820_DMA_SGDMA 1
-+#define CLK_820_CIPHER 2
-+#define CLK_820_SD 3
-+#define CLK_820_SATA 4
-+#define CLK_820_AUDIO 5
-+#define CLK_820_USBMPH 6
-+#define CLK_820_ETHA 7
-+#define CLK_820_PCIEA 8
-+#define CLK_820_NAND 9
-+#define CLK_820_PCIEB 10
-+#define CLK_820_ETHB 11
-+#define CLK_820_REF600 12
-+#define CLK_820_USBDEV 13
-
- #endif /* DT_CLOCK_OXSEMI_OX820_H */
+++ /dev/null
---- a/drivers/clk/clk-oxnas.c
-+++ b/drivers/clk/clk-oxnas.c
-@@ -5,19 +5,42 @@
- * Copyright (C) 2016 Neil Armstrong <narmstrong@baylibre.com>
- */
-
-+#include <linux/clk.h>
-+#include <linux/clkdev.h>
- #include <linux/clk-provider.h>
- #include <linux/kernel.h>
- #include <linux/init.h>
-+#include <linux/delay.h>
- #include <linux/of.h>
- #include <linux/of_device.h>
- #include <linux/platform_device.h>
- #include <linux/stringify.h>
- #include <linux/regmap.h>
- #include <linux/mfd/syscon.h>
-+#include <linux/reset.h>
-
- #include <dt-bindings/clock/oxsemi,ox810se.h>
- #include <dt-bindings/clock/oxsemi,ox820.h>
-
-+#define REF300_DIV_INT_SHIFT 8
-+#define REF300_DIV_FRAC_SHIFT 0
-+#define REF300_DIV_INT(val) ((val) << REF300_DIV_INT_SHIFT)
-+#define REF300_DIV_FRAC(val) ((val) << REF300_DIV_FRAC_SHIFT)
-+
-+#define PLLB_BYPASS 1
-+#define PLLB_ENSAT 3
-+#define PLLB_OUTDIV 4
-+#define PLLB_REFDIV 8
-+#define PLLB_DIV_INT_SHIFT 8
-+#define PLLB_DIV_FRAC_SHIFT 0
-+#define PLLB_DIV_INT(val) ((val) << PLLB_DIV_INT_SHIFT)
-+#define PLLB_DIV_FRAC(val) ((val) << PLLB_DIV_FRAC_SHIFT)
-+
-+#define PLLA_REFDIV_MASK 0x3F
-+#define PLLA_REFDIV_SHIFT 8
-+#define PLLA_OUTDIV_MASK 0x7
-+#define PLLA_OUTDIV_SHIFT 4
-+
- /* Standard regmap gate clocks */
- struct clk_oxnas_gate {
- struct clk_hw hw;
-@@ -36,6 +59,135 @@ struct oxnas_stdclk_data {
- #define CLK_SET_REGOFFSET 0x2c
- #define CLK_CLR_REGOFFSET 0x30
-
-+#define PLLA_CTRL0_REGOFFSET 0x1f0
-+#define PLLA_CTRL1_REGOFFSET 0x1f4
-+#define PLLB_CTRL0_REGOFFSET 0x1001f0
-+#define MHZ (1000 * 1000)
-+
-+struct clk_oxnas_pll {
-+ struct clk_hw hw;
-+ struct device_node *devnode;
-+ struct reset_control *rstc;
-+ struct regmap *syscon;
-+};
-+
-+#define to_clk_oxnas_pll(_hw) container_of(_hw, struct clk_oxnas_pll, hw)
-+
-+static unsigned long plla_clk_recalc_rate(struct clk_hw *hw,
-+ unsigned long parent_rate)
-+{
-+ struct clk_oxnas_pll *plla = to_clk_oxnas_pll(hw);
-+ unsigned long fin = parent_rate;
-+ unsigned long refdiv, outdiv;
-+ unsigned int pll0, fbdiv;
-+
-+ BUG_ON(regmap_read(plla->syscon, PLLA_CTRL0_REGOFFSET, &pll0));
-+
-+ refdiv = (pll0 >> PLLA_REFDIV_SHIFT) & PLLA_REFDIV_MASK;
-+ refdiv += 1;
-+ outdiv = (pll0 >> PLLA_OUTDIV_SHIFT) & PLLA_OUTDIV_MASK;
-+ outdiv += 1;
-+
-+ BUG_ON(regmap_read(plla->syscon, PLLA_CTRL1_REGOFFSET, &fbdiv));
-+ /* seems we will not be here when pll is bypassed, so ignore this
-+ * case */
-+
-+ return fin / MHZ * fbdiv / (refdiv * outdiv) / 32768 * MHZ;
-+}
-+
-+static const char *pll_clk_parents[] = {
-+ "oscillator",
-+};
-+
-+static struct clk_ops plla_ops = {
-+ .recalc_rate = plla_clk_recalc_rate,
-+};
-+
-+static struct clk_init_data clk_plla_init = {
-+ .name = "plla",
-+ .ops = &plla_ops,
-+ .parent_names = pll_clk_parents,
-+ .num_parents = ARRAY_SIZE(pll_clk_parents),
-+};
-+
-+static int pllb_clk_is_prepared(struct clk_hw *hw)
-+{
-+ struct clk_oxnas_pll *pllb = to_clk_oxnas_pll(hw);
-+
-+ return !!pllb->rstc;
-+}
-+
-+static int pllb_clk_prepare(struct clk_hw *hw)
-+{
-+ struct clk_oxnas_pll *pllb = to_clk_oxnas_pll(hw);
-+
-+ pllb->rstc = of_reset_control_get(pllb->devnode, NULL);
-+
-+ return IS_ERR(pllb->rstc) ? PTR_ERR(pllb->rstc) : 0;
-+}
-+
-+static void pllb_clk_unprepare(struct clk_hw *hw)
-+{
-+ struct clk_oxnas_pll *pllb = to_clk_oxnas_pll(hw);
-+
-+ BUG_ON(IS_ERR(pllb->rstc));
-+
-+ reset_control_put(pllb->rstc);
-+ pllb->rstc = NULL;
-+}
-+
-+static int pllb_clk_enable(struct clk_hw *hw)
-+{
-+ struct clk_oxnas_pll *pllb = to_clk_oxnas_pll(hw);
-+
-+ BUG_ON(IS_ERR(pllb->rstc));
-+
-+ /* put PLL into bypass */
-+ regmap_update_bits(pllb->syscon, PLLB_CTRL0_REGOFFSET, BIT(PLLB_BYPASS), BIT(PLLB_BYPASS));
-+ wmb();
-+ udelay(10);
-+ reset_control_assert(pllb->rstc);
-+ udelay(10);
-+ /* set PLL B control information */
-+ regmap_write_bits(pllb->syscon, PLLB_CTRL0_REGOFFSET, 0xffff,
-+ (1 << PLLB_ENSAT) | (1 << PLLB_OUTDIV) | (2 << PLLB_REFDIV));
-+ reset_control_deassert(pllb->rstc);
-+ udelay(100);
-+ regmap_update_bits(pllb->syscon, PLLB_CTRL0_REGOFFSET, BIT(PLLB_BYPASS), 0);
-+
-+ return 0;
-+}
-+
-+static void pllb_clk_disable(struct clk_hw *hw)
-+{
-+ struct clk_oxnas_pll *pllb = to_clk_oxnas_pll(hw);
-+
-+ BUG_ON(IS_ERR(pllb->rstc));
-+
-+ /* put PLL into bypass */
-+ regmap_update_bits(pllb->syscon, PLLB_CTRL0_REGOFFSET, BIT(PLLB_BYPASS), BIT(PLLB_BYPASS));
-+
-+ wmb();
-+ udelay(10);
-+
-+ reset_control_assert(pllb->rstc);
-+}
-+
-+static struct clk_ops pllb_ops = {
-+ .prepare = pllb_clk_prepare,
-+ .unprepare = pllb_clk_unprepare,
-+ .is_prepared = pllb_clk_is_prepared,
-+ .enable = pllb_clk_enable,
-+ .disable = pllb_clk_disable,
-+};
-+
-+static struct clk_init_data clk_pllb_init = {
-+ .name = "pllb",
-+ .ops = &pllb_ops,
-+ .parent_names = pll_clk_parents,
-+ .num_parents = ARRAY_SIZE(pll_clk_parents),
-+};
-+
- static inline struct clk_oxnas_gate *to_clk_oxnas_gate(struct clk_hw *hw)
- {
- return container_of(hw, struct clk_oxnas_gate, hw);
-@@ -249,3 +401,42 @@ static struct platform_driver oxnas_stdc
- },
- };
- builtin_platform_driver(oxnas_stdclk_driver);
-+
-+void __init oxnas_init_plla(struct device_node *np)
-+{
-+ struct clk *clk;
-+ struct clk_oxnas_pll *plla;
-+
-+ plla = kmalloc(sizeof(*plla), GFP_KERNEL);
-+ BUG_ON(!plla);
-+
-+ plla->syscon = syscon_node_to_regmap(of_get_parent(np));
-+ plla->hw.init = &clk_plla_init;
-+ plla->devnode = np;
-+ plla->rstc = NULL;
-+ clk = clk_register(NULL, &plla->hw);
-+ BUG_ON(IS_ERR(clk));
-+ /* mark it as enabled */
-+ clk_prepare_enable(clk);
-+ of_clk_add_provider(np, of_clk_src_simple_get, clk);
-+}
-+CLK_OF_DECLARE(oxnas_plla, "plxtech,nas782x-plla", oxnas_init_plla);
-+
-+void __init oxnas_init_pllb(struct device_node *np)
-+{
-+ struct clk *clk;
-+ struct clk_oxnas_pll *pllb;
-+
-+ pllb = kmalloc(sizeof(*pllb), GFP_KERNEL);
-+ BUG_ON(!pllb);
-+
-+ pllb->syscon = syscon_node_to_regmap(of_get_parent(np));
-+ pllb->hw.init = &clk_pllb_init;
-+ pllb->devnode = np;
-+ pllb->rstc = NULL;
-+
-+ clk = clk_register(NULL, &pllb->hw);
-+ BUG_ON(IS_ERR(clk));
-+ of_clk_add_provider(np, of_clk_src_simple_get, clk);
-+}
-+CLK_OF_DECLARE(oxnas_pllb, "plxtech,nas782x-pllb", oxnas_init_pllb);
---- a/arch/arm/boot/dts/ox820.dtsi
-+++ b/arch/arm/boot/dts/ox820.dtsi
-@@ -61,12 +61,6 @@
- clocks = <&osc>;
- };
-
-- plla: plla {
-- compatible = "fixed-clock";
-- #clock-cells = <0>;
-- clock-frequency = <850000000>;
-- };
--
- armclk: armclk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
-@@ -266,6 +260,19 @@
- compatible = "oxsemi,ox820-stdclk", "oxsemi,ox810se-stdclk";
- #clock-cells = <1>;
- };
-+
-+ plla: plla {
-+ compatible = "plxtech,nas782x-plla";
-+ #clock-cells = <0>;
-+ clocks = <&osc>;
-+ };
-+
-+ pllb: pllb {
-+ compatible = "plxtech,nas782x-pllb";
-+ #clock-cells = <0>;
-+ clocks = <&osc>;
-+ resets = <&reset RESET_PLLB>;
-+ };
- };
- };
-
-@@ -287,6 +294,13 @@
- clocks = <&armclk>;
- };
-
-+ watchdog@620 {
-+ compatible = "mpcore_wdt";
-+ reg = <0x620 0x20>;
-+ interrupts = <GIC_PPI 14 (GIC_CPU_MASK_RAW(3)|IRQ_TYPE_LEVEL_HIGH)>;
-+ clocks = <&armclk>;
-+ };
-+
- gic: interrupt-controller@1000 {
- compatible = "arm,arm11mp-gic";
- interrupt-controller;
+++ /dev/null
---- a/drivers/power/reset/Kconfig
-+++ b/drivers/power/reset/Kconfig
-@@ -141,6 +141,12 @@ config POWER_RESET_OXNAS
- help
- Restart support for OXNAS/PLXTECH OX820 SoC.
-
-+config POWER_RESET_OXNAS
-+ bool "OXNAS SoC restart driver"
-+ depends on ARCH_OXNAS
-+ help
-+ Restart support for OXNAS boards.
-+
- config POWER_RESET_PIIX4_POWEROFF
- tristate "Intel PIIX4 power-off driver"
- depends on PCI
---- a/drivers/power/reset/Makefile
-+++ b/drivers/power/reset/Makefile
-@@ -18,6 +18,7 @@ obj-$(CONFIG_POWER_RESET_QCOM_PON) += qc
- obj-$(CONFIG_POWER_RESET_OCELOT_RESET) += ocelot-reset.o
- obj-$(CONFIG_POWER_RESET_PIIX4_POWEROFF) += piix4-poweroff.o
- obj-$(CONFIG_POWER_RESET_LTC2952) += ltc2952-poweroff.o
-+obj-$(CONFIG_POWER_RESET_OXNAS) += oxnas-restart.o
- obj-$(CONFIG_POWER_RESET_QNAP) += qnap-poweroff.o
- obj-$(CONFIG_POWER_RESET_RESTART) += restart-poweroff.o
- obj-$(CONFIG_POWER_RESET_ST) += st-poweroff.o
+++ /dev/null
---- a/arch/arm/boot/dts/ox820.dtsi
-+++ b/arch/arm/boot/dts/ox820.dtsi
-@@ -247,6 +247,15 @@
- };
- };
-
-+ pcie_phy: pcie-phy@a00000 {
-+ compatible = "oxsemi,ox820-pcie-phy";
-+ reg = <0xa00000 0x10>;
-+ #phy-cells = <0>;
-+ resets = <&reset RESET_PCIEPHY>;
-+ reset-names = "phy";
-+ status = "disabled";
-+ };
-+
- sys: sys-ctrl@e00000 {
- compatible = "oxsemi,ox820-sys-ctrl", "syscon", "simple-mfd";
- reg = <0xe00000 0x200000>;
---- a/drivers/phy/Kconfig
-+++ b/drivers/phy/Kconfig
-@@ -35,6 +35,13 @@ config PHY_LPC18XX_USB_OTG
- This driver is need for USB0 support on LPC18xx/43xx and takes
- care of enabling and clock setup.
-
-+config PHY_OXNAS
-+ tristate "Oxford Semi. OX820 PCI-E PHY support"
-+ depends on HAS_IOMEM && OF && (ARM || COMPILE_TEST)
-+ select GENERIC_PHY
-+ help
-+ This option enables support for OXNAS OX820 SoC PCIE PHY.
-+
- config PHY_PISTACHIO_USB
- tristate "IMG Pistachio USB2.0 PHY driver"
- depends on MACH_PISTACHIO
---- a/drivers/phy/Makefile
-+++ b/drivers/phy/Makefile
-@@ -6,6 +6,7 @@
- obj-$(CONFIG_GENERIC_PHY) += phy-core.o
- obj-$(CONFIG_GENERIC_PHY_MIPI_DPHY) += phy-core-mipi-dphy.o
- obj-$(CONFIG_PHY_LPC18XX_USB_OTG) += phy-lpc18xx-usb-otg.o
-+obj-$(CONFIG_PHY_OXNAS) += phy-oxnas-pcie.o
- obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
- obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
- obj-$(CONFIG_USB_LGM_PHY) += phy-lgm-usb.o
+++ /dev/null
---- a/drivers/pci/controller/Kconfig
-+++ b/drivers/pci/controller/Kconfig
-@@ -305,6 +305,11 @@ config PCIE_HISI_ERR
- Say Y here if you want error handling support
- for the PCIe controller's errors on HiSilicon HIP SoCs
-
-+config PCIE_OXNAS
-+ bool "PLX Oxnas PCIe controller"
-+ depends on ARCH_OXNAS
-+ select PCIEPORTBUS
-+
- source "drivers/pci/controller/dwc/Kconfig"
- source "drivers/pci/controller/mobiveil/Kconfig"
- source "drivers/pci/controller/cadence/Kconfig"
---- a/drivers/pci/controller/Makefile
-+++ b/drivers/pci/controller/Makefile
-@@ -27,6 +27,7 @@ obj-$(CONFIG_PCIE_ROCKCHIP) += pcie-rock
- obj-$(CONFIG_PCIE_ROCKCHIP_EP) += pcie-rockchip-ep.o
- obj-$(CONFIG_PCIE_ROCKCHIP_HOST) += pcie-rockchip-host.o
- obj-$(CONFIG_PCIE_MEDIATEK) += pcie-mediatek.o
-+obj-$(CONFIG_PCIE_OXNAS) += pcie-oxnas.o
- obj-$(CONFIG_PCIE_TANGO_SMP8759) += pcie-tango.o
- obj-$(CONFIG_VMD) += vmd.o
- obj-$(CONFIG_PCIE_BRCMSTB) += pcie-brcmstb.o
---- a/arch/arm/boot/dts/ox820.dtsi
-+++ b/arch/arm/boot/dts/ox820.dtsi
-@@ -289,7 +289,7 @@
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
-- ranges = <0 0x47000000 0x1000000>;
-+ ranges = <0 0x47000000 0x2000>;
-
- scu: scu@0 {
- compatible = "arm,arm11mp-scu";
-@@ -318,5 +318,86 @@
- <0x100 0x500>;
- };
- };
-+
-+ pcie0: pcie-controller@47c00000 {
-+ compatible = "plxtech,nas782x-pcie";
-+ device_type = "pci";
-+ #address-cells = <3>;
-+ #size-cells = <2>;
-+
-+ /* flag & space bus address host address size */
-+ ranges = < 0x82000000 0 0x48000000 0x48000000 0 0x2000000
-+ 0xC2000000 0 0x4A000000 0x4A000000 0 0x1E00000
-+ 0x81000000 0 0x4BE00000 0x4BE00000 0 0x0100000
-+ 0x80000000 0 0x4BF00000 0x4BF00000 0 0x0100000>;
-+
-+ bus-range = <0x00 0x7f>;
-+
-+ /* cfg inbound translator */
-+ reg = <0x47c00000 0x1000>, <0x47d00000 0x100>;
-+
-+ phys = <&pcie_phy>;
-+ phy-names = "pcie-phy";
-+
-+ #interrupt-cells = <1>;
-+ /* wild card mask, match all bus address & interrupt specifier */
-+ /* format: bus address mask, interrupt specifier mask */
-+ /* each bit 1 means need match, 0 means ignored when match */
-+ interrupt-map-mask = <0 0 0 0>;
-+ /* format: a list of: bus address, interrupt specifier,
-+ * parent interrupt controller & specifier */
-+ interrupt-map = <0 0 0 0 &gic 0 19 0x304>;
-+ gpios = <&gpio1 12 0>;
-+ clocks = <&stdclk CLK_820_PCIEA>, <&pllb>;
-+ clock-names = "pcie", "busclk";
-+ resets = <&reset RESET_PCIEA>;
-+ reset-names = "pcie";
-+
-+ plxtech,pcie-hcsl-bit = <2>;
-+ plxtech,pcie-ctrl-offset = <0x120>;
-+ plxtech,pcie-outbound-offset = <0x138>;
-+ status = "disabled";
-+ };
-+
-+ pcie1: pcie-controller@47e00000 {
-+ compatible = "plxtech,nas782x-pcie";
-+ device_type = "pci";
-+ #address-cells = <3>;
-+ #size-cells = <2>;
-+
-+ /* flag & space bus address host address size */
-+ ranges = < 0x82000000 0 0x4C000000 0x4C000000 0 0x2000000
-+ 0xC2000000 0 0x4E000000 0x4E000000 0 0x1E00000
-+ 0x81000000 0 0x4FE00000 0x4FE00000 0 0x0100000
-+ 0x80000000 0 0x4FF00000 0x4FF00000 0 0x0100000>;
-+
-+ bus-range = <0x80 0xff>;
-+
-+ /* cfg inbound translator */
-+ reg = <0x47e00000 0x1000>, <0x47f00000 0x100>;
-+
-+ phys = <&pcie_phy>;
-+ phy-names = "pcie-phy";
-+
-+ #interrupt-cells = <1>;
-+ /* wild card mask, match all bus address & interrupt specifier */
-+ /* format: bus address mask, interrupt specifier mask */
-+ /* each bit 1 means need match, 0 means ignored when match */
-+ interrupt-map-mask = <0 0 0 0>;
-+ /* format: a list of: bus address, interrupt specifier,
-+ * parent interrupt controller & specifier */
-+ interrupt-map = <0 0 0 0 &gic 0 20 0x304>;
-+
-+ /* gpios = <&gpio1 12 0>; */
-+ clocks = <&stdclk CLK_820_PCIEB>, <&pllb>;
-+ clock-names = "pcie", "busclk";
-+ resets = <&reset RESET_PCIEB>;
-+ reset-names = "pcie";
-+
-+ plxtech,pcie-hcsl-bit = <3>;
-+ plxtech,pcie-ctrl-offset = <0x124>;
-+ plxtech,pcie-outbound-offset = <0x174>;
-+ status = "disabled";
-+ };
- };
- };
+++ /dev/null
---- a/drivers/ata/Kconfig
-+++ b/drivers/ata/Kconfig
-@@ -568,6 +568,14 @@ config SATA_VITESSE
-
- If unsure, say N.
-
-+config SATA_OXNAS
-+ tristate "PLXTECH NAS782X SATA support"
-+ select SATA_HOST
-+ help
-+ This option enables support for Nas782x Serial ATA controller.
-+
-+ If unsure, say N.
-+
- comment "PATA SFF controllers with BMDMA"
-
- config PATA_ALI
---- a/drivers/ata/Makefile
-+++ b/drivers/ata/Makefile
-@@ -46,6 +46,7 @@ obj-$(CONFIG_SATA_SVW) += sata_svw.o
- obj-$(CONFIG_SATA_ULI) += sata_uli.o
- obj-$(CONFIG_SATA_VIA) += sata_via.o
- obj-$(CONFIG_SATA_VITESSE) += sata_vsc.o
-+obj-$(CONFIG_SATA_OXNAS) += sata_oxnas.o
-
- # SFF PATA w/ BMDMA
- obj-$(CONFIG_PATA_ALI) += pata_ali.o
---- a/arch/arm/boot/dts/ox820.dtsi
-+++ b/arch/arm/boot/dts/ox820.dtsi
-@@ -399,5 +399,20 @@
- plxtech,pcie-outbound-offset = <0x174>;
- status = "disabled";
- };
-+
-+ sata: sata@45900000 {
-+ compatible = "plxtech,nas782x-sata";
-+ /* ports dmactl sgdma */
-+ reg = <0x45900000 0x20000>, <0x459A0000 0x40>, <0x459B0000 0x20>,
-+ /* core phy descriptors (optional) */
-+ <0x459E0000 0x2000>, <0x44900000 0x0C>, <0x50000000 0x1000>;
-+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&stdclk CLK_820_SATA>;
-+ resets = <&reset RESET_SATA>, <&reset RESET_SATA_LINK>, <&reset RESET_SATA_PHY>;
-+ reset-names = "sata", "link", "phy";
-+ nr-ports = <1>;
-+ status = "disabled";
-+ };
-+
- };
- };
---- a/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts
-+++ b/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts
-@@ -111,3 +111,7 @@
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_etha_mdio>;
- };
-+
-+&sata {
-+ status = "okay";
-+};
+++ /dev/null
---- a/arch/arm/mach-oxnas/Kconfig
-+++ b/arch/arm/mach-oxnas/Kconfig
-@@ -2,6 +2,7 @@
- menuconfig ARCH_OXNAS
- bool "Oxford Semiconductor OXNAS Family SoCs"
- select ARCH_HAS_RESET_CONTROLLER
-+ select ARCH_WANT_LIBATA_LEDS
- select COMMON_CLK_OXNAS
- select GPIOLIB
- select MFD_SYSCON
+++ /dev/null
---- a/drivers/usb/host/Kconfig
-+++ b/drivers/usb/host/Kconfig
-@@ -350,6 +350,13 @@ config USB_OCTEON_EHCI
- USB 2.0 device support. All CN6XXX based chips with USB are
- supported.
-
-+config USB_EHCI_OXNAS
-+ tristate "OXNAS EHCI Module"
-+ depends on USB_EHCI_HCD && ARCH_OXNAS
-+ select USB_EHCI_ROOT_HUB_TT
-+ help
-+ Enable support for the OX820 SOC's on-chip EHCI controller.
-+
- endif # USB_EHCI_HCD
-
- config USB_OXU210HP_HCD
---- a/drivers/usb/host/Makefile
-+++ b/drivers/usb/host/Makefile
-@@ -48,6 +48,7 @@ obj-$(CONFIG_USB_EHCI_HCD_SPEAR) += ehci
- obj-$(CONFIG_USB_EHCI_HCD_STI) += ehci-st.o
- obj-$(CONFIG_USB_EHCI_EXYNOS) += ehci-exynos.o
- obj-$(CONFIG_USB_EHCI_HCD_AT91) += ehci-atmel.o
-+obj-$(CONFIG_USB_EHCI_OXNAS) += ehci-oxnas.o
- obj-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o
- obj-$(CONFIG_USB_EHCI_BRCMSTB) += ehci-brcm.o
-
---- a/arch/arm/boot/dts/ox820.dtsi
-+++ b/arch/arm/boot/dts/ox820.dtsi
-@@ -106,6 +106,31 @@
- status = "disabled";
- };
-
-+ ehci: ehci@40200100 {
-+ compatible = "plxtech,nas782x-ehci";
-+ reg = <0x40200100 0xf00>;
-+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&stdclk CLK_820_USBMPH>, <&pllb>, <&stdclk CLK_820_REF600>;
-+ clock-names = "usb", "refsrc", "phyref";
-+ resets = <&reset RESET_USBHS>, <&reset RESET_USBPHYA>, <&reset RESET_USBPHYB>;
-+ reset-names = "host", "phya", "phyb";
-+ oxsemi,sys-ctrl = <&sys>;
-+ /* Otherwise ref300 is used, which is derived from sata phy
-+ * in that case, usb depends on sata initialization */
-+ /* FIXME: how to make this dependency explicit ? */
-+ oxsemi,ehci_use_pllb;
-+ status = "disabled";
-+
-+ ehci_port1: port@1 {
-+ reg = <1>;
-+ #trigger-source-cells = <0>;
-+ };
-+ ehci_port2: port@2 {
-+ reg = <2>;
-+ #trigger-source-cells = <0>;
-+ };
-+ };
-+
- apb-bridge@44000000 {
- #address-cells = <1>;
- #size-cells = <1>;
---- a/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts
-+++ b/arch/arm/boot/dts/ox820-cloudengines-pogoplug-series-3.dts
-@@ -105,6 +105,10 @@
- };
- };
-
-+&ehci {
-+ status = "okay";
-+};
-+
- ða {
- status = "okay";
-
+++ /dev/null
-From 71270226b14733a4b1f2cde58ea9265caa50b38d Mon Sep 17 00:00:00 2001
-From: Adrian Panella <ianchi74@outlook.com>
-Date: Thu, 9 Mar 2017 09:37:17 +0100
-Subject: [PATCH 67/69] generic: Mangle bootloader's kernel arguments
-
-The command-line arguments provided by the boot loader will be
-appended to a new device tree property: bootloader-args.
-If there is a property "append-rootblock" in DT under /chosen
-and a root= option in bootloaders command line it will be parsed
-and added to DT bootargs with the form: <append-rootblock>XX.
-Only command line ATAG will be processed, the rest of the ATAGs
-sent by bootloader will be ignored.
-This is usefull in dual boot systems, to get the current root partition
-without afecting the rest of the system.
-
-Signed-off-by: Adrian Panella <ianchi74@outlook.com>
----
- arch/arm/Kconfig | 11 +++++
- arch/arm/boot/compressed/atags_to_fdt.c | 72 ++++++++++++++++++++++++++++++++-
- init/main.c | 16 ++++++++
- 3 files changed, 98 insertions(+), 1 deletion(-)
-
---- a/arch/arm/Kconfig
-+++ b/arch/arm/Kconfig
-@@ -1777,6 +1777,17 @@ config ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEN
- The command-line arguments provided by the boot loader will be
- appended to the the device tree bootargs property.
-
-+config ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE
-+ bool "Append rootblock parsing bootloader's kernel arguments"
-+ help
-+ The command-line arguments provided by the boot loader will be
-+ appended to a new device tree property: bootloader-args.
-+ If there is a property "append-rootblock" in DT under /chosen
-+ and a root= option in bootloaders command line it will be parsed
-+ and added to DT bootargs with the form: <append-rootblock>XX.
-+ Only command line ATAG will be processed, the rest of the ATAGs
-+ sent by bootloader will be ignored.
-+
- endchoice
-
- config CMDLINE
---- a/arch/arm/boot/compressed/atags_to_fdt.c
-+++ b/arch/arm/boot/compressed/atags_to_fdt.c
-@@ -5,6 +5,8 @@
-
- #if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND)
- #define do_extend_cmdline 1
-+#elif defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
-+#define do_extend_cmdline 1
- #else
- #define do_extend_cmdline 0
- #endif
-@@ -69,6 +71,59 @@ static uint32_t get_cell_size(const void
- return cell_size;
- }
-
-+#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
-+
-+static char *append_rootblock(char *dest, const char *str, int len, void *fdt)
-+{
-+ char *ptr, *end;
-+ char *root="root=";
-+ int i, l;
-+ const char *rootblock;
-+
-+ //ARM doesn't have __HAVE_ARCH_STRSTR, so search manually
-+ ptr = str - 1;
-+
-+ do {
-+ //first find an 'r' at the begining or after a space
-+ do {
-+ ptr++;
-+ ptr = strchr(ptr, 'r');
-+ if(!ptr) return dest;
-+
-+ } while (ptr != str && *(ptr-1) != ' ');
-+
-+ //then check for the rest
-+ for(i = 1; i <= 4; i++)
-+ if(*(ptr+i) != *(root+i)) break;
-+
-+ } while (i != 5);
-+
-+ end = strchr(ptr, ' ');
-+ end = end ? (end - 1) : (strchr(ptr, 0) - 1);
-+
-+ //find partition number (assumes format root=/dev/mtdXX | /dev/mtdblockXX | yy:XX )
-+ for( i = 0; end >= ptr && *end >= '0' && *end <= '9'; end--, i++);
-+ ptr = end + 1;
-+
-+ /* if append-rootblock property is set use it to append to command line */
-+ rootblock = getprop(fdt, "/chosen", "append-rootblock", &l);
-+ if(rootblock != NULL) {
-+ if(*dest != ' ') {
-+ *dest = ' ';
-+ dest++;
-+ len++;
-+ }
-+ if (len + l + i <= COMMAND_LINE_SIZE) {
-+ memcpy(dest, rootblock, l);
-+ dest += l - 1;
-+ memcpy(dest, ptr, i);
-+ dest += i;
-+ }
-+ }
-+ return dest;
-+}
-+#endif
-+
- static void merge_fdt_bootargs(void *fdt, const char *fdt_cmdline)
- {
- char cmdline[COMMAND_LINE_SIZE];
-@@ -88,12 +143,21 @@ static void merge_fdt_bootargs(void *fdt
-
- /* and append the ATAG_CMDLINE */
- if (fdt_cmdline) {
-+
-+#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
-+ //save original bootloader args
-+ //and append ubi.mtd with root partition number to current cmdline
-+ setprop_string(fdt, "/chosen", "bootloader-args", fdt_cmdline);
-+ ptr = append_rootblock(ptr, fdt_cmdline, len, fdt);
-+
-+#else
- len = strlen(fdt_cmdline);
- if (ptr - cmdline + len + 2 < COMMAND_LINE_SIZE) {
- *ptr++ = ' ';
- memcpy(ptr, fdt_cmdline, len);
- ptr += len;
- }
-+#endif
- }
- *ptr = '\0';
-
-@@ -168,7 +232,9 @@ int atags_to_fdt(void *atag_list, void *
- else
- setprop_string(fdt, "/chosen", "bootargs",
- atag->u.cmdline.cmdline);
-- } else if (atag->hdr.tag == ATAG_MEM) {
-+ }
-+#ifndef CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE
-+ else if (atag->hdr.tag == ATAG_MEM) {
- if (memcount >= sizeof(mem_reg_property)/4)
- continue;
- if (!atag->u.mem.size)
-@@ -212,6 +278,10 @@ int atags_to_fdt(void *atag_list, void *
- setprop(fdt, "/memory", "reg", mem_reg_property,
- 4 * memcount * memsize);
- }
-+#else
-+
-+ }
-+#endif
-
- return fdt_pack(fdt);
- }
---- a/init/main.c
-+++ b/init/main.c
-@@ -110,6 +110,10 @@
-
- #include <kunit/test.h>
-
-+#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
-+#include <linux/of.h>
-+#endif
-+
- static int kernel_init(void *);
-
- extern void init_IRQ(void);
-@@ -904,6 +908,18 @@ asmlinkage __visible void __init __no_sa
- page_alloc_init();
-
- pr_notice("Kernel command line: %s\n", saved_command_line);
-+
-+#if defined(CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_MANGLE)
-+ //Show bootloader's original command line for reference
-+ if(of_chosen) {
-+ const char *prop = of_get_property(of_chosen, "bootloader-args", NULL);
-+ if(prop)
-+ pr_notice("Bootloader command line (ignored): %s\n", prop);
-+ else
-+ pr_notice("Bootloader command line not present\n");
-+ }
-+#endif
-+
- /* parameters may set static keys */
- jump_label_init();
- parse_early_param();
+++ /dev/null
---- a/drivers/ata/libata-core.c
-+++ b/drivers/ata/libata-core.c
-@@ -1528,6 +1528,14 @@ unsigned ata_exec_internal_sg(struct ata
- return AC_ERR_SYSTEM;
- }
-
-+ if (ap->ops->acquire_hw && !ap->ops->acquire_hw(ap, 0, 0)) {
-+ spin_unlock_irqrestore(ap->lock, flags);
-+ if (!ap->ops->acquire_hw(ap, 1, (2*HZ))) {
-+ return AC_ERR_TIMEOUT;
-+ }
-+ spin_lock_irqsave(ap->lock, flags);
-+ }
-+
- /* initialize internal qc */
- qc = __ata_qc_from_tag(ap, ATA_TAG_INTERNAL);
-
-@@ -4562,6 +4570,9 @@ struct ata_queued_cmd *ata_qc_new_init(s
- if (unlikely(ap->pflags & ATA_PFLAG_FROZEN))
- return NULL;
-
-+ if (ap->ops->qc_new && ap->ops->qc_new(ap))
-+ return NULL;
-+
- /* libsas case */
- if (ap->flags & ATA_FLAG_SAS_HOST) {
- tag = ata_sas_allocate_tag(ap);
-@@ -4607,6 +4618,8 @@ void ata_qc_free(struct ata_queued_cmd *
- qc->tag = ATA_TAG_POISON;
- if (ap->flags & ATA_FLAG_SAS_HOST)
- ata_sas_free_tag(tag, ap);
-+ if (ap->ops->qc_free)
-+ ap->ops->qc_free(qc);
- }
- }
-
---- a/include/linux/libata.h
-+++ b/include/linux/libata.h
-@@ -912,6 +912,8 @@ struct ata_port_operations {
- enum ata_completion_errors (*qc_prep)(struct ata_queued_cmd *qc);
- unsigned int (*qc_issue)(struct ata_queued_cmd *qc);
- bool (*qc_fill_rtf)(struct ata_queued_cmd *qc);
-+ int (*qc_new)(struct ata_port *ap);
-+ void (*qc_free)(struct ata_queued_cmd *qc);
-
- /*
- * Configuration and exception handling
-@@ -1002,6 +1004,9 @@ struct ata_port_operations {
- void (*phy_reset)(struct ata_port *ap);
- void (*eng_timeout)(struct ata_port *ap);
-
-+ int (*acquire_hw)(struct ata_port *ap, int may_sleep,
-+ int timeout_jiffies);
-+
- /*
- * ->inherits must be the last field and all the preceding
- * fields must be pointers.
projects / openwrt / staging / xback.git / commitdiff