static void __init MP_processor_info (struct mpc_config_processor *m)
{
- int ver;
+ int ver, cpu;
static int found_bsp=0;
if (!(m->mpc_cpuflag & CPU_ENABLED))
return;
}
- num_processors++;
+ cpu = num_processors++;
if (m->mpc_apicid > MAX_APICS) {
printk(KERN_ERR "Processor #%d INVALID. (Max ID: %d).\n",
* in same order as logical cpu numbers. Hence the first
* entry is BSP, and so on.
*/
+ cpu = 0;
+
bios_cpu_apicid[0] = m->mpc_apicid;
x86_cpu_to_apicid[0] = m->mpc_apicid;
found_bsp = 1;
- } else {
- bios_cpu_apicid[num_processors - found_bsp] = m->mpc_apicid;
- x86_cpu_to_apicid[num_processors - found_bsp] = m->mpc_apicid;
- }
+ } else
+ cpu = num_processors - found_bsp;
+ bios_cpu_apicid[cpu] = m->mpc_apicid;
+ x86_cpu_to_apicid[cpu] = m->mpc_apicid;
+
+ cpu_set(cpu, cpu_possible_map);
+ cpu_set(cpu, cpu_present_map);
}
static void __init MP_bus_info (struct mpc_config_bus *m)
#define get_idle_for_cpu(x) (idle_thread_array[(x)])
#define set_idle_for_cpu(x,p) (idle_thread_array[(x)] = (p))
-/*
- * cpu_possible_map should be static, it cannot change as cpu's
- * are onlined, or offlined. The reason is per-cpu data-structures
- * are allocated by some modules at init time, and dont expect to
- * do this dynamically on cpu arrival/departure.
- * cpu_present_map on the other hand can change dynamically.
- * In case when cpu_hotplug is not compiled, then we resort to current
- * behaviour, which is cpu_possible == cpu_present.
- * If cpu-hotplug is supported, then we need to preallocate for all
- * those NR_CPUS, hence cpu_possible_map represents entire NR_CPUS range.
- * - Ashok Raj
- */
-#ifdef CONFIG_HOTPLUG_CPU
-#define fixup_cpu_possible_map(x) cpu_set((x), cpu_possible_map)
-#else
-#define fixup_cpu_possible_map(x)
-#endif
-
/*
* Currently trivial. Write the real->protected mode
* bootstrap into the page concerned. The caller
}
}
+#ifdef CONFIG_HOTPLUG_CPU
+/*
+ * cpu_possible_map should be static, it cannot change as cpu's
+ * are onlined, or offlined. The reason is per-cpu data-structures
+ * are allocated by some modules at init time, and dont expect to
+ * do this dynamically on cpu arrival/departure.
+ * cpu_present_map on the other hand can change dynamically.
+ * In case when cpu_hotplug is not compiled, then we resort to current
+ * behaviour, which is cpu_possible == cpu_present.
+ * If cpu-hotplug is supported, then we need to preallocate for all
+ * those NR_CPUS, hence cpu_possible_map represents entire NR_CPUS range.
+ * - Ashok Raj
+ */
+static void prefill_possible_map(void)
+{
+ int i;
+ for (i = 0; i < NR_CPUS; i++)
+ cpu_set(i, cpu_possible_map);
+}
+#endif
+
/*
* Various sanity checks.
*/
*/
void __init smp_prepare_cpus(unsigned int max_cpus)
{
- int i;
-
nmi_watchdog_default();
current_cpu_data = boot_cpu_data;
current_thread_info()->cpu = 0; /* needed? */
enforce_max_cpus(max_cpus);
- /*
- * Fill in cpu_present_mask
- */
- for (i = 0; i < NR_CPUS; i++) {
- int apicid = cpu_present_to_apicid(i);
- if (physid_isset(apicid, phys_cpu_present_map)) {
- cpu_set(i, cpu_present_map);
- cpu_set(i, cpu_possible_map);
- }
- fixup_cpu_possible_map(i);
- }
+#ifdef CONFIG_HOTPLUG_CPU
+ prefill_possible_map();
+#endif
if (smp_sanity_check(max_cpus) < 0) {
printk(KERN_INFO "SMP disabled\n");