--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca953x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ /delete-property/ bootargs;
+ };
+
+ aliases {
+ led-boot = &led_status_green;
+ led-failsafe = &led_status_green;
+ led-running = &led_status_green;
+ led-upgrade = &led_status_green;
+ label-mac-device = ð0;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ status_red {
+ label = "red:status";
+ gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_status_green: status_green {
+ label = "green:status";
+ gpios = <&gpio 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ status_blue {
+ label = "blue:status";
+ gpios = <&gpio 3 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ hw_algo = "toggle";
+ /* hw_margin_ms is actually 300s but driver limits it to 60s */
+ hw_margin_ms = <60000>;
+ always-running;
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ /* partitions are passed via bootloader */
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x040000 0x040000>;
+ };
+
+ partition@80000 {
+ label = "custom";
+ reg = <0x080000 0x140000>;
+ read-only;
+ };
+
+ partition@1c0000 {
+ label = "inactive";
+ reg = <0x1c0000 0x700000>;
+ };
+
+ partition@8c0000 {
+ label = "inactive2";
+ reg = <0x8c0000 0x700000>;
+ };
+
+ art: partition@fc0000 {
+ label = "ART";
+ reg = <0xfc0000 0x040000>;
+ read-only;
+ };
+ };
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-handle = <&swphy4>;
+
+ mtd-mac-address = <&art 0x0>;
+};
+
+ð1 {
+ /* Workaround: keep the Ethernet interfaces order/mapping correct
+ * (GMAC0 -> eth0, GMAC1 -> eth1, same as in old ar71xx target)
+ */
+ compatible = "qca,qca9530-eth", "syscon", "simple-mfd";
+
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <1>;
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&art 0x0>;
+ mtd-mac-address-increment = <2>;
+};
--- /dev/null
+# The U-Boot loader with the datachk patchset for dualbooting requires image
+# sizes and checksums to be provided in the U-Boot environment.
+# The devices come with 2 main partitions - while one is active
+# sysupgrade will flash the other. The boot order is changed to boot the
+# newly flashed partition. If the new partition can't be booted due to
+# upgrade failures the previously used partition is loaded.
+
+platform_do_upgrade_dualboot_datachk() {
+ local tar_file="$1"
+ local restore_backup
+ local primary_kernel_mtd
+
+ local setenv_script="/tmp/fw_env_upgrade"
+
+ local inactive_mtd="$(find_mtd_index $PART_NAME)"
+ local inactive_offset="$(cat /sys/class/mtd/mtd${inactive_mtd}/offset)"
+ local total_size="$(cat /sys/class/mtd/mtd${inactive_mtd}/size)"
+ local flash_start_mem=0x9f000000
+
+ # detect to which flash region the new image is written to.
+ #
+ # 1. check what is the mtd index for the first flash region on this
+ # device
+ # 2. check if the target partition ("inactive") has the mtd index of
+ # the first flash region
+ #
+ # - when it is: the new bootseq will be 1,2 and the first region is
+ # modified
+ # - when it isnt: bootseq will be 2,1 and the second region is
+ # modified
+ #
+ # The detection has to be done via the hardcoded mtd partition because
+ # the current boot might be done with the fallback region. Let us
+ # assume that the current bootseq is 1,2. The bootloader detected that
+ # the image in flash region 1 is corrupt and thus switches to flash
+ # region 2. The bootseq in the u-boot-env is now still the same and
+ # the sysupgrade code can now only rely on the actual mtd indexes and
+ # not the bootseq variable to detect the currently booted flash
+ # region/image.
+ #
+ # In the above example, an implementation which uses bootseq ("1,2") to
+ # detect the currently booted image would assume that region 1 is booted
+ # and then overwrite the variables for the wrong flash region (aka the
+ # one which isn't modified). This could result in a device which doesn't
+ # boot anymore to Linux until it was reflashed with ap51-flash.
+ local next_boot_part="1"
+ case "$(board_name)" in
+ plasmacloud,pa300)
+ primary_kernel_mtd=3
+ ;;
+ *)
+ echo "failed to detect primary kernel mtd partition for board"
+ return 1
+ ;;
+ esac
+ [ "$inactive_mtd" = "$primary_kernel_mtd" ] || next_boot_part="2"
+
+ local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$')
+ board_dir=${board_dir%/}
+
+ local kernel_length=$(tar xf $tar_file ${board_dir}/kernel -O | wc -c)
+ local rootfs_length=$(tar xf $tar_file ${board_dir}/root -O | wc -c)
+ # rootfs without EOF marker
+ rootfs_length=$((rootfs_length-4))
+
+ local kernel_md5=$(tar xf $tar_file ${board_dir}/kernel -O | md5sum); kernel_md5="${kernel_md5%% *}"
+ # md5 checksum of rootfs with EOF marker
+ local rootfs_md5=$(tar xf $tar_file ${board_dir}/root -O | dd bs=1 count=$rootfs_length | md5sum); rootfs_md5="${rootfs_md5%% *}"
+
+ #
+ # add tar support to get_image() to use default_do_upgrade() instead?
+ #
+
+ # take care of restoring a saved config
+ [ -n "$UPGRADE_BACKUP" ] && restore_backup="${MTD_CONFIG_ARGS} -j ${UPGRADE_BACKUP}"
+
+ mtd -q erase inactive
+ tar xf $tar_file ${board_dir}/root -O | mtd -n -p $kernel_length $restore_backup write - $PART_NAME
+ tar xf $tar_file ${board_dir}/kernel -O | mtd -n write - $PART_NAME
+
+ # prepare new u-boot env
+ if [ "$next_boot_part" = "1" ]; then
+ echo "bootseq 1,2" > $setenv_script
+ else
+ echo "bootseq 2,1" > $setenv_script
+ fi
+
+ printf "kernel_size_%i %i\n" $next_boot_part $((kernel_length / 1024)) >> $setenv_script
+ printf "vmlinux_start_addr 0x%08x\n" $((flash_start_mem + inactive_offset)) >> $setenv_script
+ printf "vmlinux_size 0x%08x\n" ${kernel_length} >> $setenv_script
+ printf "vmlinux_checksum %s\n" ${kernel_md5} >> $setenv_script
+
+ printf "rootfs_size_%i %i\n" $next_boot_part $(((total_size-kernel_length) / 1024)) >> $setenv_script
+ printf "rootfs_start_addr 0x%08x\n" $((flash_start_mem+inactive_offset+kernel_length)) >> $setenv_script
+ printf "rootfs_size 0x%08x\n" ${rootfs_length} >> $setenv_script
+ printf "rootfs_checksum %s\n" ${rootfs_md5} >> $setenv_script
+
+ # store u-boot env changes
+ mkdir -p /var/lock
+ fw_setenv -s $setenv_script || {
+ echo "failed to update U-Boot environment"
+ return 1
+ }
+}