ARM: at91: Remove the support for the RSI EWS board

The platform is end of life/support and should not clutter
the mach-at91 directory with non-DT files. It is therefore
removed.

Signed-off-by: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

diff --git a/arch/arm/mach-at91/Kconfig.non_dt b/arch/arm/mach-at91/Kconfig.non_dt
index a2ee352a890418222c06f1fa892a7e482d39e9fc..aa31e556e2e59506c2a5a618fb70a6356255e70a 100644 (file)
--- a/arch/arm/mach-at91/Kconfig.non_dt
+++ b/arch/arm/mach-at91/Kconfig.non_dt
@@ -132,12 +132,6 @@ config MACH_ECO920
        bool "eco920"
        help
          Select this if you are using the eco920 board
-
-config MACH_RSI_EWS
-       bool "RSI Embedded Webserver"
-       depends on ARCH_AT91RM9200
-       help
-         Select this if you are using RSIs EWS board.
 endif
 
 # ----------------------------------------------------------

diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index e8efcb00ca942ba76b1de799123124ccde3ee392..c677f9688ffe119235d0a1ba29446731bb7ca3e6 100644 (file)
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -46,7 +46,6 @@ obj-$(CONFIG_MACH_ECBAT91)    += board-ecbat91.o
 obj-$(CONFIG_MACH_YL9200)      += board-yl-9200.o
 obj-$(CONFIG_MACH_CPUAT91)     += board-cpuat91.o
 obj-$(CONFIG_MACH_ECO920)      += board-eco920.o
-obj-$(CONFIG_MACH_RSI_EWS)     += board-rsi-ews.o
 
 # AT91SAM9260 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o

diff --git a/arch/arm/mach-at91/board-rsi-ews.c b/arch/arm/mach-at91/board-rsi-ews.c
deleted file mode 100644 (file)
index f28e8b7..0000000
--- a/arch/arm/mach-at91/board-rsi-ews.c
+++ /dev/null
@@ -1,232 +0,0 @@
-/*
- * board-rsi-ews.c
- *
- *  Copyright (C)
- *  2005 SAN People,
- *  2008-2011 R-S-I Elektrotechnik GmbH & Co. KG
- *
- * Licensed under GPLv2 or later.
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/mtd/physmap.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-
-#include <linux/gpio.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-static void __init rsi_ews_init_early(void)
-{
-       /* Initialize processor: 18.432 MHz crystal */
-       at91_initialize(18432000);
-}
-
-/*
- * Ethernet
- */
-static struct macb_platform_data rsi_ews_eth_data __initdata = {
-       .phy_irq_pin    = AT91_PIN_PC4,
-       .is_rmii        = 1,
-};
-
-/*
- * USB Host
- */
-static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
-       .ports          = 1,
-       .vbus_pin       = {-EINVAL, -EINVAL},
-       .overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * SD/MC
- */
-static struct mci_platform_data __initdata rsi_ews_mci0_data = {
-       .slot[0] = {
-               .bus_width      = 4,
-               .detect_pin     = AT91_PIN_PB27,
-               .wp_pin         = AT91_PIN_PB29,
-       },
-};
-
-/*
- * I2C
- */
-static struct i2c_board_info rsi_ews_i2c_devices[] __initdata = {
-       {
-               I2C_BOARD_INFO("ds1337", 0x68),
-       },
-       {
-               I2C_BOARD_INFO("24c01", 0x50),
-       }
-};
-
-/*
- * LEDs
- */
-static struct gpio_led rsi_ews_leds[] = {
-       {
-               .name                   = "led0",
-               .gpio                   = AT91_PIN_PB6,
-               .active_low             = 0,
-       },
-       {
-               .name                   = "led1",
-               .gpio                   = AT91_PIN_PB7,
-               .active_low             = 0,
-       },
-       {
-               .name                   = "led2",
-               .gpio                   = AT91_PIN_PB8,
-               .active_low             = 0,
-       },
-       {
-               .name                   = "led3",
-               .gpio                   = AT91_PIN_PB9,
-               .active_low             = 0,
-       },
-};
-
-/*
- * DataFlash
- */
-static struct spi_board_info rsi_ews_spi_devices[] = {
-       {       /* DataFlash chip 1*/
-               .modalias       = "mtd_dataflash",
-               .chip_select    = 0,
-               .max_speed_hz   = 5 * 1000 * 1000,
-       },
-       {       /* DataFlash chip 2*/
-               .modalias       = "mtd_dataflash",
-               .chip_select    = 1,
-               .max_speed_hz   = 5 * 1000 * 1000,
-       },
-};
-
-/*
- * NOR flash
- */
-static struct mtd_partition rsiews_nor_partitions[] = {
-       {
-               .name           = "boot",
-               .offset         = 0,
-               .size           = 3 * SZ_128K,
-               .mask_flags     = MTD_WRITEABLE
-       },
-       {
-               .name           = "kernel",
-               .offset         = MTDPART_OFS_NXTBLK,
-               .size           = SZ_2M - (3 * SZ_128K)
-       },
-       {
-               .name           = "root",
-               .offset         = MTDPART_OFS_NXTBLK,
-               .size           = SZ_8M
-       },
-       {
-               .name           = "kernelupd",
-               .offset         = MTDPART_OFS_NXTBLK,
-               .size           = 3 * SZ_512K,
-               .mask_flags     = MTD_WRITEABLE
-       },
-       {
-               .name           = "rootupd",
-               .offset         = MTDPART_OFS_NXTBLK,
-               .size           = 9 * SZ_512K,
-               .mask_flags     = MTD_WRITEABLE
-       },
-};
-
-static struct physmap_flash_data rsiews_nor_data = {
-       .width          = 2,
-       .parts          = rsiews_nor_partitions,
-       .nr_parts       = ARRAY_SIZE(rsiews_nor_partitions),
-};
-
-#define NOR_BASE       AT91_CHIPSELECT_0
-#define NOR_SIZE       SZ_16M
-
-static struct resource nor_flash_resources[] = {
-       {
-               .start  = NOR_BASE,
-               .end    = NOR_BASE + NOR_SIZE - 1,
-               .flags  = IORESOURCE_MEM,
-       }
-};
-
-static struct platform_device rsiews_nor_flash = {
-       .name           = "physmap-flash",
-       .id             = 0,
-       .dev            = {
-                               .platform_data  = &rsiews_nor_data,
-       },
-       .resource       = nor_flash_resources,
-       .num_resources  = ARRAY_SIZE(nor_flash_resources),
-};
-
-/*
- * Init Func
- */
-static void __init rsi_ews_board_init(void)
-{
-       /* Serial */
-       /* DBGU on ttyS0. (Rx & Tx only) */
-       /* This one is for debugging */
-       at91_register_uart(0, 0, 0);
-
-       /* USART1 on ttyS2. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-       /* Dialin/-out modem interface */
-       at91_register_uart(AT91RM9200_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS
-                          | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-                          | ATMEL_UART_RI);
-
-       /* USART3 on ttyS4. (Rx, Tx, RTS) */
-       /* RS485 communication */
-       at91_register_uart(AT91RM9200_ID_US3, 4, ATMEL_UART_RTS);
-       at91_add_device_serial();
-       at91_set_gpio_output(AT91_PIN_PA21, 0);
-       /* Ethernet */
-       at91_add_device_eth(&rsi_ews_eth_data);
-       /* USB Host */
-       at91_add_device_usbh(&rsi_ews_usbh_data);
-       /* I2C */
-       at91_add_device_i2c(rsi_ews_i2c_devices,
-                       ARRAY_SIZE(rsi_ews_i2c_devices));
-       /* SPI */
-       at91_add_device_spi(rsi_ews_spi_devices,
-                       ARRAY_SIZE(rsi_ews_spi_devices));
-       /* MMC */
-       at91_add_device_mci(0, &rsi_ews_mci0_data);
-       /* NOR Flash */
-       platform_device_register(&rsiews_nor_flash);
-       /* LEDs */
-       at91_gpio_leds(rsi_ews_leds, ARRAY_SIZE(rsi_ews_leds));
-}
-
-MACHINE_START(RSI_EWS, "RSI EWS")
-       /* Maintainer: Josef Holzmayr <holzmayr@rsi-elektrotechnik.de> */
-       .init_time      = at91rm9200_timer_init,
-       .map_io         = at91_map_io,
-       .handle_irq     = at91_aic_handle_irq,
-       .init_early     = rsi_ews_init_early,
-       .init_irq       = at91_init_irq_default,
-       .init_machine   = rsi_ews_board_init,
-MACHINE_END