+++ /dev/null
-
-* Samsung S2MPA01 Voltage and Current Regulator
-
-The Samsung S2MPA01 is a multi-function device which includes high
-efficiency buck converters including Dual-Phase buck converter, various LDOs,
-and an RTC. It is interfaced to the host controller using an I2C interface.
-Each sub-block is addressed by the host system using different I2C slave
-addresses.
-
-Required properties:
-- compatible: Should be "samsung,s2mpa01-pmic".
-- reg: Specifies the I2C slave address of the PMIC block. It should be 0x66.
-
-Optional properties:
-- interrupt-parent: Specifies the phandle of the interrupt controller to which
- the interrupts from s2mpa01 are delivered to.
-- interrupts: An interrupt specifier for the sole interrupt generated by the
- device.
-
-Optional nodes:
-- regulators: The regulators of s2mpa01 that have to be instantiated should be
- included in a sub-node named 'regulators'. Regulator nodes and constraints
- included in this sub-node use the standard regulator bindings which are
- documented elsewhere.
-
-Properties for BUCK regulator nodes:
-- regulator-ramp-delay: ramp delay in uV/us. May be 6250, 12500
- (default), 25000, or 50000. May be 0 for disabling the ramp delay on
- BUCK{1,2,3,4}.
-
- In the absence of the regulator-ramp-delay property, the default ramp
- delay will be used.
-
- NOTE: Some BUCKs share the ramp rate setting i.e. same ramp value will be set
- for a particular group of BUCKs. So provide same regulator-ramp-delay=<value>.
-
- The following BUCKs share ramp settings:
- * 1 and 6
- * 2 and 4
- * 8, 9, and 10
-
-The following are the names of the regulators that the s2mpa01 PMIC block
-supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
-as per the datasheet of s2mpa01.
-
- - LDOn
- - valid values for n are 1 to 26
- - Example: LDO1, LD02, LDO26
- - BUCKn
- - valid values for n are 1 to 10.
- - Example: BUCK1, BUCK2, BUCK9
-
-Example:
-
- s2mpa01_pmic@66 {
- compatible = "samsung,s2mpa01-pmic";
- reg = <0x66>;
-
- regulators {
- ldo1_reg: LDO1 {
- regulator-name = "VDD_ALIVE";
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1000000>;
- };
-
- ldo2_reg: LDO2 {
- regulator-name = "VDDQ_MMC2";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- regulator-always-on;
- };
-
- buck1_reg: BUCK1 {
- regulator-name = "vdd_mif";
- regulator-min-microvolt = <950000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- buck2_reg: BUCK2 {
- regulator-name = "vdd_arm";
- regulator-min-microvolt = <950000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-ramp-delay = <50000>;
- };
- };
- };
This is a part of device tree bindings for S2M and S5M family multi-function
devices.
-The Samsung S2MPS11/13/14/15, S2MPU02 and S5M8767 is a family
+The Samsung S2MPA01, S2MPS11/13/14/15, S2MPU02 and S5M8767 is a family
of multi-function devices which include voltage and current regulators, RTC,
charger controller, clock outputs and other sub-blocks. It is interfaced
to the host controller using an I2C interface. Each sub-block is usually
This document describes bindings for main device node. Optional sub-blocks
must be a sub-nodes to it. Bindings for them can be found in:
+ - bindings/regulator/samsung,s2mpa01.txt
- bindings/regulator/samsung,s2mps11.txt
- bindings/regulator/samsung,s5m8767.txt
- bindings/clock/samsung,s2mps11.txt
Required properties:
- compatible: Should be one of the following
+ - "samsung,s2mpa01-pmic",
- "samsung,s2mps11-pmic",
- "samsung,s2mps13-pmic",
- "samsung,s2mps14-pmic",
--- /dev/null
+Binding for Samsung S2MPA01 regulator block
+===========================================
+
+This is a part of device tree bindings for S2M family multi-function devices.
+More information can be found in bindings/mfd/sec-core.txt file.
+
+The S2MPA01 device provide buck and LDO regulators.
+
+To register these with regulator framework instantiate under main device node
+a sub-node named "regulators" with more sub-nodes for each regulator using the
+common regulator binding documented in:
+ - Documentation/devicetree/bindings/regulator/regulator.txt
+
+
+Names of regulators supported by S2MPA01 device:
+ - LDOn
+ - valid values for n are 1 to 26
+ - Example: LDO1, LD02, LDO26
+ - BUCKn
+ - valid values for n are 1 to 10.
+ - Example: BUCK1, BUCK2, BUCK9
+Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
+as per the datasheet of device.
+
+
+Optional properties of buck regulator nodes under "regulators" sub-node:
+ - regulator-ramp-delay: ramp delay in uV/us. May be 6250, 12500
+ (default), 25000, or 50000. May be 0 for disabling the ramp delay on
+ BUCK{1,2,3,4}.
+
+ In the absence of the regulator-ramp-delay property, the default ramp
+ delay will be used.
+
+ Note: Some bucks share the ramp rate setting i.e. same ramp value
+ will be set for a particular group of bucks so provide the same
+ regulator-ramp-delay value for them.
+ Groups sharing ramp rate:
+ - buck{1,6},
+ - buck{2,4},
+ - buck{8,9,10}.
+
+Example:
+
+ s2mpa01_pmic@66 {
+ compatible = "samsung,s2mpa01-pmic";
+ reg = <0x66>;
+
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VDD_ALIVE";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VDDQ_MMC2";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-ramp-delay = <50000>;
+ };
+ };
+ };
projects / openwrt / staging / blogic.git / commitdiff