After the kernel has switched version to 5.10, JA76PF2 and
RouterStations lost the capability to sysupgrade the OpenWrt version.
The cause is the lack of porting the patches responsible for partial
flash erase block writing and these boards FIS directory and RedBoot
config partitions share the same erase block. Because of that the FIS
directory can't be updated to accommodate kernel/rootfs partition size
changes. This could be remedied by bootloader update, but it is very
intrusive and could potentially lead to non-trivial recovery procedure,
if something went wrong. The less difficult option is to use OpenWrt
kernel loader, which will let us use static partition sizes and employ
mtd splitter to dynamically adjust kernel and rootfs partition sizes.
On sysupgrade from ath79 19.07 or 21.02 image, which still let to modify
FIS directory, the loader will be written to kernel partition, while the
kernel+rootfs to rootfs partition.
The caveats are:
* image format changes, no possible upgrade from ar71xx target images
* downgrade to any older OpenWrt version will require TFTP recovery or
usage of bootloader command line interface
To downgrade to 19.07 or 21.02, or to upgrade if one is already on
OpenWrt with kernel 5.10, for RouterStations use TFTP recovery
procedure. For JA76PF2 use instructions from this commit message:
commit
0cc87b3bacee ("ath79: image: disable sysupgrade images for routerstations and ja76pf2"),
replacing kernel image with loader (loader.bin suffix) and rootfs
image with firmware (firmware.bin suffix).
Fixes: b10d6044599d ("kernel: add linux 5.10 support")
Fixes: 15aa53d7ee65 ("ath79: switch to Kernel 5.10")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(mkubntimage was moved to generic-ubnt.mk)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/mtd/partitions/uimage.h>
/ {
model = "jjPlus JA76PF2";
spi-max-frequency = <25000000>;
partitions {
+ compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
- compatible = "ecoscentric,redboot-fis-partitions";
+
+ partition@0 {
+ label = "RedBoot";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "loader";
+ reg = <0x040000 0x020000>;
+ };
+
+ partition@60000 {
+ label = "firmware";
+ reg = <0x060000 0xf80000>;
+ compatible = "openwrt,uimage", "denx,uimage";
+ openwrt,ih-magic = <IH_MAGIC_OKLI>;
+ };
+
+ partition@fe0000 {
+ label = "FIS directory";
+ reg = <0xfe0000 0x00f000>;
+ read-only;
+ };
+
+ partition@fef000 {
+ label = "RedBoot config";
+ reg = <0xfef000 0x001000>;
+ read-only;
+ };
+
+ partition@ff0000 {
+ label = "Atheros Board Data";
+ reg = <0xff0000 0x10000>;
+ read-only;
+ };
};
};
};
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
+#include <dt-bindings/mtd/partitions/uimage.h>
/ {
aliases {
spi-max-frequency = <25000000>;
partitions {
- compatible = "ecoscentric,redboot-fis-partitions";
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "RedBoot";
+ reg = <0x000000 0x030000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "loader";
+ reg = <0x030000 0x020000>;
+ };
+
+ partition@50000 {
+ label = "firmware";
+ reg = <0x050000 0xfa0000>;
+ compatible = "openwrt,uimage", "denx,uimage";
+ openwrt,ih-magic = <IH_MAGIC_OKLI>;
+ };
+
+ partition@ff0000 {
+ label = "FIS directory";
+ reg = <0xff0000 0x00f000>;
+ read-only;
+ };
+
+ partition@fff000 {
+ label = "RedBoot config";
+ reg = <0xfff000 0x001000>;
+ read-only;
+ };
};
};
};
. /lib/functions.sh
case "$(board_name)" in
+ jjplus,ja76pf2|\
meraki,mr12|\
- meraki,mr16)
+ meraki,mr16|\
+ ubnt,routerstation|\
+ ubnt,routerstation-pro)
uci set system.@system[0].compat_version="2.0"
uci commit system
;;
local kern_part="$2"
local magic=$(get_magic_word "$sysup_file")
- if [ "$magic" = "4349" ]; then
- local kern_length=0x$(dd if="$sysup_file" bs=2 skip=1 count=4 2>/dev/null)
+ if [ "$magic" = "7379" ]; then
+ local board_dir=$(tar tf $sysup_file | grep -m 1 '^sysupgrade-.*/$')
[ -f "$UPGRADE_BACKUP" ] && append="-j $UPGRADE_BACKUP"
- dd if="$sysup_file" bs=64k skip=1 2>/dev/null | \
- mtd -r $append -F$kern_part:$kern_length:0x80060000,rootfs write - $kern_part:rootfs
- elif [ "$magic" = "7379" ]; then
- local board_dir=$(tar tf $sysup_file | grep -m 1 '^sysupgrade-.*/$')
- local kern_length=$(tar xf $sysup_file ${board_dir}kernel -O | wc -c)
+ if grep -q "mtd1.*loader" /proc/mtd; then
+ tar xf $sysup_file ${board_dir}kernel ${board_dir}root -O | \
+ mtd -r $append write - loader:firmware
- [ -f "$UPGRADE_BACKUP" ] && append="-j $UPGRADE_BACKUP"
- tar xf $sysup_file ${board_dir}kernel ${board_dir}root -O | \
- mtd -r $append -F$kern_part:$kern_length:0x80060000,rootfs write - $kern_part:rootfs
+ else
+ local kern_length=$(tar xf $sysup_file ${board_dir}kernel -O | wc -c)
+ tar xf $sysup_file ${board_dir}kernel ${board_dir}root -O | \
+ mtd -r $append -F$kern_part:$kern_length:0x80060000,rootfs write - $kern_part:rootfs
+ fi
else
echo "Unknown image, aborting!"
return 1
DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID
DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION
-define Build/combined-image
- sh $(TOPDIR)/scripts/combined-image.sh \
- "$(IMAGE_KERNEL)" \
- "$@" \
- "$@.new"
- @mv $@.new $@
-endef
-
define Build/loader-common
rm -rf $@.src
$(MAKE) -C lzma-loader \
define Build/mkubntimage
-$(STAGING_DIR_HOST)/bin/mkfwimage -B $(UBNT_BOARD) \
-v $(UBNT_TYPE).$(UBNT_CHIP).v6.0.0-$(VERSION_DIST)-$(REVISION) \
- -k $(IMAGE_KERNEL) -r $@ -o $@
+ -k $(if $(1),$(1),$(IMAGE_KERNEL)) -r $@ -o $@
endef
define Build/mkubntimage2
kmod-usb2 fconfig
DEVICE_VENDOR := Ubiquiti
SOC := ar7161
- IMAGE_SIZE := 16128k
+ LOADER_TYPE := bin
+ LOADER_FLASH_OFFS := 0x50000
+ COMPILE := loader-$(1).bin
+ COMPILE/loader-$(1).bin := loader-okli-compile | lzma | pad-to 128k
+ IMAGE_SIZE := 16000k
IMAGES += factory.bin
- IMAGE/factory.bin := append-rootfs | pad-rootfs | mkubntimage | \
- check-size
- IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | combined-image | \
- check-size | append-metadata
- KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
+ IMAGE/factory.bin := append-kernel | uImage lzma -M 0x4f4b4c49 | pad-to $$$$(BLOCKSIZE) | \
+ append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | \
+ mkubntimage $$$$(KDIR)/loader-$(1).bin | check-size
+ IMAGE/sysupgrade.bin := append-kernel | uImage lzma -M 0x4f4b4c49 | pad-to $$$$(BLOCKSIZE) | \
+ append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | check-size | \
+ sysupgrade-tar kernel=$$$$(KDIR)/loader-$(1).bin rootfs=$$$$@ | append-metadata
+ KERNEL := kernel-bin | append-dtb | lzma
KERNEL_INITRAMFS := kernel-bin | append-dtb
+ DEVICE_COMPAT_VERSION := 2.0
+ DEVICE_COMPAT_MESSAGE := Partition design has changed compared to older versions (19.07 and 21.02) \
+ due to kernel drivers restrictions. Upgrade via sysupgrade mechanism is one way operation. \
+ Downgrading OpenWrt version will involve usage of TFTP recovery or bootloader command line interface.
endef
define Device/ubnt_routerstation
UBNT_TYPE := RSx
UBNT_CHIP := ar7100
DEVICE_PACKAGES += -swconfig
- SUPPORTED_DEVICES += routerstation
endef
TARGET_DEVICES += ubnt_routerstation
UBNT_BOARD := RSPRO
UBNT_TYPE := RSPRO
UBNT_CHIP := ar7100pro
- SUPPORTED_DEVICES += routerstation-pro
endef
TARGET_DEVICES += ubnt_routerstation-pro
DEVICE_VENDOR := jjPlus
DEVICE_MODEL := JA76PF2
DEVICE_PACKAGES += -kmod-ath9k -swconfig -wpad-basic-wolfssl -uboot-envtools fconfig kmod-hwmon-lm75
- IMAGES += kernel.bin rootfs.bin
- IMAGE/kernel.bin := append-kernel
- IMAGE/rootfs.bin := append-rootfs | pad-rootfs
- IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | combined-image | \
- check-size | append-metadata
- KERNEL := kernel-bin | append-dtb | lzma | pad-to $$(BLOCKSIZE)
+ LOADER_TYPE := bin
+ LOADER_FLASH_OFFS := 0x60000
+ COMPILE := loader-$(1).bin
+ COMPILE/loader-$(1).bin := loader-okli-compile | lzma | pad-to 128k
+ ARTIFACTS := loader.bin
+ ARTIFACT/loader.bin := append-loader-okli $(1)
+ IMAGES += firmware.bin
+ IMAGE/firmware.bin := append-kernel | uImage lzma -M 0x4f4b4c49 | pad-to $$$$(BLOCKSIZE) | \
+ append-rootfs | pad-rootfs | pad-to $$$$(BLOCKSIZE) | check-size
+ IMAGE/sysupgrade.bin := $$(IMAGE/firmware.bin) | \
+ sysupgrade-tar kernel=$$$$(KDIR)/loader-$(1).bin rootfs=$$$$@ | append-metadata
+ KERNEL := kernel-bin | append-dtb | lzma
KERNEL_INITRAMFS := kernel-bin | append-dtb
- IMAGE_SIZE := 16000k
- SUPPORTED_DEVICES += ja76pf2
+ IMAGE_SIZE := 15872k
+ DEVICE_COMPAT_VERSION := 2.0
+ DEVICE_COMPAT_MESSAGE := Partition design has changed compared to older versions (19.07 and 21.02) \
+ due to kernel drivers restrictions. Upgrade via sysupgrade mechanism is one way operation. \
+ Downgrading OpenWrt version will involve usage of bootloader command line interface.
endef
TARGET_DEVICES += jjplus_ja76pf2