#endif /* CONFIG_ISA */
} /* cy_detect_isa */
-static void plx_init(void __iomem * addr, __u32 initctl)
+#ifdef CONFIG_PCI
+static void __devinit plx_init(void __iomem * addr, __u32 initctl)
{
/* Reset PLX */
cy_writel(addr + initctl, readl(addr + initctl) | 0x40000000);
return 0;
}
-/*
- * ---------------------------------------------------------------------
- * cy_detect_pci() - Test PCI bus presence and Cyclom-Ye/PCI.
- * sets global variables and return the number of PCI boards found.
- * ---------------------------------------------------------------------
- */
-static int __init cy_detect_pci(void)
+static int __devinit cy_pci_probe(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
{
-#ifdef CONFIG_PCI
-
- struct pci_dev *pdev = NULL;
unsigned char cyy_rev_id;
- unsigned char cy_pci_irq = 0;
- __u32 cy_pci_phys0, cy_pci_phys2;
+ unsigned char cy_pci_irq;
+ __u32 cy_pci_phys0, cy_pci_phys2, mailbox;
void __iomem *cy_pci_addr0, *cy_pci_addr2;
- unsigned short i, j, cy_pci_nchan, plx_ver;
- unsigned short device_id, dev_index = 0;
- __u32 mailbox;
+ unsigned int device_id;
+ unsigned short j, cy_pci_nchan, plx_ver;
int retval;
- for (i = 0; i < NR_CARDS; i++) {
- /* look for a Cyclades card by vendor and device id */
- while ((device_id = cy_pci_dev_id[dev_index].device) != 0) {
- if ((pdev = pci_get_device(PCI_VENDOR_ID_CYCLADES,
- device_id, pdev)) == NULL) {
- dev_index++; /* try next device id */
- } else {
- break; /* found a board */
- }
- }
+ retval = pci_enable_device(pdev);
+ if (retval) {
+ dev_err(&pdev->dev, "cannot enable device\n");
+ return retval;
+ }
- if (device_id == 0)
- break;
+ /* read PCI configuration area */
+ cy_pci_irq = pdev->irq;
+ cy_pci_phys0 = pci_resource_start(pdev, 0);
+ cy_pci_phys2 = pci_resource_start(pdev, 2);
+ pci_read_config_byte(pdev, PCI_REVISION_ID, &cyy_rev_id);
- if (pci_enable_device(pdev))
- continue;
+ device_id = pdev->device & ~PCI_DEVICE_ID_MASK;
- /* read PCI configuration area */
- cy_pci_irq = pdev->irq;
- cy_pci_phys0 = pci_resource_start(pdev, 0);
- cy_pci_phys2 = pci_resource_start(pdev, 2);
- pci_read_config_byte(pdev, PCI_REVISION_ID, &cyy_rev_id);
+ if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
+ device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
+#ifdef CY_PCI_DEBUG
+ printk("Cyclom-Y/PCI (bus=0x0%x, pci_id=0x%x, ",
+ pdev->bus->number, pdev->devfn);
+ printk("rev_id=%d) IRQ%d\n",
+ cyy_rev_id, (int)cy_pci_irq);
+ printk("Cyclom-Y/PCI:found winaddr=0x%lx "
+ "ctladdr=0x%lx\n",
+ (ulong)cy_pci_phys2, (ulong)cy_pci_phys0);
+#endif
- device_id &= ~PCI_DEVICE_ID_MASK;
+ if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
+ printk(" Warning: PCI I/O bit incorrectly "
+ "set. Ignoring it...\n");
+ pdev->resource[2].flags &= ~IORESOURCE_IO;
+ }
- if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo ||
- device_id == PCI_DEVICE_ID_CYCLOM_Y_Hi) {
-#ifdef CY_PCI_DEBUG
+ /* Although we don't use this I/O region, we should
+ request it from the kernel anyway, to avoid problems
+ with other drivers accessing it. */
+ retval = pci_request_regions(pdev, "Cyclom-Y");
+ if (retval) {
+ printk(KERN_ERR "cyclades: failed to reserve "
+ "PCI resources\n");
+ return retval;
+ }
+#if defined(__alpha__)
+ if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo) { /* below 1M? */
printk("Cyclom-Y/PCI (bus=0x0%x, pci_id=0x%x, ",
pdev->bus->number, pdev->devfn);
printk("rev_id=%d) IRQ%d\n",
cyy_rev_id, (int)cy_pci_irq);
printk("Cyclom-Y/PCI:found winaddr=0x%lx "
"ctladdr=0x%lx\n",
- (ulong)cy_pci_phys2, (ulong)cy_pci_phys0);
-#endif
-
- if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
- printk(" Warning: PCI I/O bit incorrectly "
- "set. Ignoring it...\n");
- pdev->resource[2].flags &= ~IORESOURCE_IO;
- }
-
- /* Although we don't use this I/O region, we should
- request it from the kernel anyway, to avoid problems
- with other drivers accessing it. */
- if (pci_request_regions(pdev, "Cyclom-Y") != 0) {
- printk(KERN_ERR "cyclades: failed to reserve "
- "PCI resources\n");
- continue;
- }
-#if defined(__alpha__)
- if (device_id == PCI_DEVICE_ID_CYCLOM_Y_Lo) { /* below 1M? */
- printk("Cyclom-Y/PCI (bus=0x0%x, pci_id=0x%x, ",
- pdev->bus->number, pdev->devfn);
- printk("rev_id=%d) IRQ%d\n",
- cyy_rev_id, (int)cy_pci_irq);
- printk("Cyclom-Y/PCI:found winaddr=0x%lx "
- "ctladdr=0x%lx\n",
- (ulong)cy_pci_phys2,
- (ulong)cy_pci_phys0);
- printk("Cyclom-Y/PCI not supported for low "
- "addresses in Alpha systems.\n");
- i--;
- continue;
- }
+ (ulong)cy_pci_phys2,
+ (ulong)cy_pci_phys0);
+ printk("Cyclom-Y/PCI not supported for low "
+ "addresses in Alpha systems.\n");
+ return -EIO;
+ }
#endif
- cy_pci_addr0 = pci_iomap(pdev, 0, CyPCI_Yctl);
- cy_pci_addr2 = pci_iomap(pdev, 2, CyPCI_Ywin);
+ cy_pci_addr0 = pci_iomap(pdev, 0, CyPCI_Yctl);
+ cy_pci_addr2 = pci_iomap(pdev, 2, CyPCI_Ywin);
#ifdef CY_PCI_DEBUG
- printk("Cyclom-Y/PCI: relocate winaddr=0x%lx "
- "ctladdr=0x%lx\n",
- (u_long)cy_pci_addr2, (u_long)cy_pci_addr0);
+ printk("Cyclom-Y/PCI: relocate winaddr=0x%lx "
+ "ctladdr=0x%lx\n",
+ (u_long)cy_pci_addr2, (u_long)cy_pci_addr0);
#endif
- cy_pci_nchan = (unsigned short)(CyPORTS_PER_CHIP *
- cyy_init_card(cy_pci_addr2, 1));
- if (cy_pci_nchan == 0) {
- printk("Cyclom-Y PCI host card with ");
- printk("no Serial-Modules at 0x%lx.\n",
- (ulong) cy_pci_phys2);
- i--;
- continue;
- }
- if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) {
- printk("Cyclom-Y/PCI found at 0x%lx ",
- (ulong) cy_pci_phys2);
- printk("but no channels are available.\n");
- printk("Change NR_PORTS in cyclades.c and "
- "recompile kernel.\n");
- return i;
- }
- /* fill the next cy_card structure available */
- for (j = 0; j < NR_CARDS; j++) {
- if (cy_card[j].base_addr == 0)
- break;
- }
- if (j == NR_CARDS) { /* no more cy_cards available */
- printk("Cyclom-Y/PCI found at 0x%lx ",
- (ulong) cy_pci_phys2);
- printk("but no more cards can be used.\n");
- printk("Change NR_CARDS in cyclades.c and "
- "recompile kernel.\n");
- return i;
- }
-
- /* allocate IRQ */
- if (request_irq(cy_pci_irq, cyy_interrupt,
- IRQF_SHARED, "Cyclom-Y", &cy_card[j])) {
- printk("Cyclom-Y/PCI found at 0x%lx ",
- (ulong) cy_pci_phys2);
- printk("but could not allocate IRQ%d.\n",
- cy_pci_irq);
- return i;
- }
-
- /* set cy_card */
- cy_card[j].base_phys = (ulong) cy_pci_phys2;
- cy_card[j].ctl_phys = (ulong) cy_pci_phys0;
- cy_card[j].base_addr = cy_pci_addr2;
- cy_card[j].ctl_addr = cy_pci_addr0;
- cy_card[j].irq = (int)cy_pci_irq;
- cy_card[j].bus_index = 1;
- cy_card[j].first_line = cy_next_channel;
- cy_card[j].num_chips = cy_pci_nchan / 4;
- cy_card[j].pdev = pdev;
- pci_set_drvdata(pdev, &cy_card[j]);
-
- /* enable interrupts in the PCI interface */
- plx_ver = readb(cy_pci_addr2 + CyPLX_VER) & 0x0f;
- switch (plx_ver) {
- case PLX_9050:
-
- cy_writeb(cy_pci_addr0 + 0x4c, 0x43);
+ cy_pci_nchan = (unsigned short)(CyPORTS_PER_CHIP *
+ cyy_init_card(cy_pci_addr2, 1));
+ if (cy_pci_nchan == 0) {
+ printk("Cyclom-Y PCI host card with ");
+ printk("no Serial-Modules at 0x%lx.\n",
+ (ulong) cy_pci_phys2);
+ return -EIO;
+ }
+ if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) {
+ printk("Cyclom-Y/PCI found at 0x%lx ",
+ (ulong) cy_pci_phys2);
+ printk("but no channels are available.\n");
+ printk("Change NR_PORTS in cyclades.c and "
+ "recompile kernel.\n");
+ return -EIO;
+ }
+ /* fill the next cy_card structure available */
+ for (j = 0; j < NR_CARDS; j++) {
+ if (cy_card[j].base_addr == 0)
break;
+ }
+ if (j == NR_CARDS) { /* no more cy_cards available */
+ printk("Cyclom-Y/PCI found at 0x%lx ",
+ (ulong) cy_pci_phys2);
+ printk("but no more cards can be used.\n");
+ printk("Change NR_CARDS in cyclades.c and "
+ "recompile kernel.\n");
+ return -EIO;
+ }
- case PLX_9060:
- case PLX_9080:
- default: /* Old boards, use PLX_9060 */
-
- plx_init(cy_pci_addr0, 0x6c);
- /* For some yet unknown reason, once the PLX9060 reloads
- the EEPROM, the IRQ is lost and, thus, we have to
- re-write it to the PCI config. registers.
- This will remain here until we find a permanent
- fix. */
- pci_write_config_byte(pdev, PCI_INTERRUPT_LINE,
- cy_pci_irq);
-
- cy_writew(cy_pci_addr0 + 0x68,
- readw(cy_pci_addr0 + 0x68) | 0x0900);
- break;
- }
+ /* allocate IRQ */
+ retval = request_irq(cy_pci_irq, cyy_interrupt,
+ IRQF_SHARED, "Cyclom-Y", &cy_card[j]);
+ if (retval) {
+ printk("Cyclom-Y/PCI found at 0x%lx ",
+ (ulong) cy_pci_phys2);
+ printk("but could not allocate IRQ%d.\n",
+ cy_pci_irq);
+ return retval;
+ }
- /* print message */
- printk("Cyclom-Y/PCI #%d: 0x%lx-0x%lx, IRQ%d, ",
- j + 1, (ulong)cy_pci_phys2,
- (ulong) (cy_pci_phys2 + CyPCI_Ywin - 1),
- (int)cy_pci_irq);
- printk("%d channels starting from port %d.\n",
- cy_pci_nchan, cy_next_channel);
+ /* set cy_card */
+ cy_card[j].base_phys = (ulong) cy_pci_phys2;
+ cy_card[j].ctl_phys = (ulong) cy_pci_phys0;
+ cy_card[j].base_addr = cy_pci_addr2;
+ cy_card[j].ctl_addr = cy_pci_addr0;
+ cy_card[j].irq = (int)cy_pci_irq;
+ cy_card[j].bus_index = 1;
+ cy_card[j].first_line = cy_next_channel;
+ cy_card[j].num_chips = cy_pci_nchan / 4;
+ cy_card[j].pdev = pdev;
+ pci_set_drvdata(pdev, &cy_card[j]);
- cy_next_channel += cy_pci_nchan;
- } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Lo) {
- /* print message */
- printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ",
- pdev->bus->number, pdev->devfn);
- printk("rev_id=%d) IRQ%d\n",
- cyy_rev_id, (int)cy_pci_irq);
- printk("Cyclades-Z/PCI: found winaddr=0x%lx "
- "ctladdr=0x%lx\n",
- (ulong)cy_pci_phys2, (ulong)cy_pci_phys0);
- printk("Cyclades-Z/PCI not supported for low "
- "addresses\n");
+ /* enable interrupts in the PCI interface */
+ plx_ver = readb(cy_pci_addr2 + CyPLX_VER) & 0x0f;
+ switch (plx_ver) {
+ case PLX_9050:
+
+ cy_writeb(cy_pci_addr0 + 0x4c, 0x43);
break;
- } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Hi) {
-#ifdef CY_PCI_DEBUG
- printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ",
- pdev->bus->number, pdev->devfn);
- printk("rev_id=%d) IRQ%d\n",
- cyy_rev_id, (int)cy_pci_irq);
- printk("Cyclades-Z/PCI: found winaddr=0x%lx "
- "ctladdr=0x%lx\n",
- (ulong) cy_pci_phys2, (ulong) cy_pci_phys0);
-#endif
- cy_pci_addr0 = pci_iomap(pdev, 0, CyPCI_Zctl);
- /* Disable interrupts on the PLX before resetting it */
- cy_writew(cy_pci_addr0 + 0x68,
- readw(cy_pci_addr0 + 0x68) & ~0x0900);
+ case PLX_9060:
+ case PLX_9080:
+ default: /* Old boards, use PLX_9060 */
plx_init(cy_pci_addr0, 0x6c);
- /* For some yet unknown reason, once the PLX9060 reloads
- the EEPROM, the IRQ is lost and, thus, we have to
- re-write it to the PCI config. registers.
- This will remain here until we find a permanent
- fix. */
+ /* For some yet unknown reason, once the PLX9060 reloads
+ the EEPROM, the IRQ is lost and, thus, we have to
+ re-write it to the PCI config. registers.
+ This will remain here until we find a permanent
+ fix. */
pci_write_config_byte(pdev, PCI_INTERRUPT_LINE,
- cy_pci_irq);
+ cy_pci_irq);
- mailbox = (__u32)readl(&((struct RUNTIME_9060 __iomem *)
- cy_pci_addr0)->mail_box_0);
+ cy_writew(cy_pci_addr0 + 0x68,
+ readw(cy_pci_addr0 + 0x68) | 0x0900);
+ break;
+ }
- if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
- printk(" Warning: PCI I/O bit incorrectly "
- "set. Ignoring it...\n");
- pdev->resource[2].flags &= ~IORESOURCE_IO;
- }
+ /* print message */
+ printk("Cyclom-Y/PCI #%d: 0x%lx-0x%lx, IRQ%d, ",
+ j + 1, (ulong)cy_pci_phys2,
+ (ulong) (cy_pci_phys2 + CyPCI_Ywin - 1),
+ (int)cy_pci_irq);
+ printk("%d channels starting from port %d.\n",
+ cy_pci_nchan, cy_next_channel);
- /* Although we don't use this I/O region, we should
- request it from the kernel anyway, to avoid problems
- with other drivers accessing it. */
- if (pci_request_regions(pdev, "Cyclades-Z") != 0) {
- printk(KERN_ERR "cyclades: failed to reserve "
- "PCI resources\n");
- continue;
- }
+ cy_next_channel += cy_pci_nchan;
+ } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Lo) {
+ /* print message */
+ printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ",
+ pdev->bus->number, pdev->devfn);
+ printk("rev_id=%d) IRQ%d\n",
+ cyy_rev_id, (int)cy_pci_irq);
+ printk("Cyclades-Z/PCI: found winaddr=0x%lx "
+ "ctladdr=0x%lx\n",
+ (ulong)cy_pci_phys2, (ulong)cy_pci_phys0);
+ printk("Cyclades-Z/PCI not supported for low "
+ "addresses\n");
+ return -EIO;
+ } else if (device_id == PCI_DEVICE_ID_CYCLOM_Z_Hi) {
+#ifdef CY_PCI_DEBUG
+ printk("Cyclades-Z/PCI (bus=0x0%x, pci_id=0x%x, ",
+ pdev->bus->number, pdev->devfn);
+ printk("rev_id=%d) IRQ%d\n",
+ cyy_rev_id, (int)cy_pci_irq);
+ printk("Cyclades-Z/PCI: found winaddr=0x%lx "
+ "ctladdr=0x%lx\n",
+ (ulong) cy_pci_phys2, (ulong) cy_pci_phys0);
+#endif
+ cy_pci_addr0 = pci_iomap(pdev, 0, CyPCI_Zctl);
+
+ /* Disable interrupts on the PLX before resetting it */
+ cy_writew(cy_pci_addr0 + 0x68,
+ readw(cy_pci_addr0 + 0x68) & ~0x0900);
+
+ plx_init(cy_pci_addr0, 0x6c);
+ /* For some yet unknown reason, once the PLX9060 reloads
+ the EEPROM, the IRQ is lost and, thus, we have to
+ re-write it to the PCI config. registers.
+ This will remain here until we find a permanent
+ fix. */
+ pci_write_config_byte(pdev, PCI_INTERRUPT_LINE,
+ cy_pci_irq);
- if (mailbox == ZE_V1) {
- retval = cy_init_Ze(cy_pci_phys0, cy_pci_phys2,
- cy_pci_addr0, cy_pci_irq, pdev);
- if (retval < 0)
- i--;
- continue;
- } else {
- cy_pci_addr2 = pci_iomap(pdev, 2, CyPCI_Zwin);
- }
+ mailbox = (__u32)readl(&((struct RUNTIME_9060 __iomem *)
+ cy_pci_addr0)->mail_box_0);
+
+ if (pci_resource_flags(pdev, 2) & IORESOURCE_IO) {
+ printk(" Warning: PCI I/O bit incorrectly "
+ "set. Ignoring it...\n");
+ pdev->resource[2].flags &= ~IORESOURCE_IO;
+ }
+
+ /* Although we don't use this I/O region, we should
+ request it from the kernel anyway, to avoid problems
+ with other drivers accessing it. */
+ retval = pci_request_regions(pdev, "Cyclades-Z");
+ if (retval) {
+ printk(KERN_ERR "cyclades: failed to reserve "
+ "PCI resources\n");
+ return retval;
+ }
+
+ if (mailbox == ZE_V1) {
+ retval = cy_init_Ze(cy_pci_phys0, cy_pci_phys2,
+ cy_pci_addr0, cy_pci_irq, pdev);
+ return retval;
+ } else {
+ cy_pci_addr2 = pci_iomap(pdev, 2, CyPCI_Zwin);
+ }
#ifdef CY_PCI_DEBUG
- printk("Cyclades-Z/PCI: relocate winaddr=0x%lx "
- "ctladdr=0x%lx\n",
- (ulong) cy_pci_addr2, (ulong) cy_pci_addr0);
- if (mailbox == ZO_V1) {
- cy_writel(&((struct RUNTIME_9060 *)
- (cy_pci_addr0))->loc_addr_base,
- WIN_CREG);
- printk("Cyclades-8Zo/PCI: FPGA id %lx, ver "
- "%lx\n", (ulong) (0xff &
- readl(&((struct CUSTOM_REG *)
- (cy_pci_addr2))->fpga_id)),
- (ulong)(0xff &
- readl(&((struct CUSTOM_REG *)
- (cy_pci_addr2))->
- fpga_version)));
- cy_writel(&((struct RUNTIME_9060 *)
- (cy_pci_addr0))->loc_addr_base,
- WIN_RAM);
- } else {
- printk("Cyclades-Z/PCI: New Cyclades-Z board. "
- "FPGA not loaded\n");
- }
+ printk("Cyclades-Z/PCI: relocate winaddr=0x%lx "
+ "ctladdr=0x%lx\n",
+ (ulong) cy_pci_addr2, (ulong) cy_pci_addr0);
+ if (mailbox == ZO_V1) {
+ cy_writel(&((struct RUNTIME_9060 *)
+ (cy_pci_addr0))->loc_addr_base,
+ WIN_CREG);
+ printk("Cyclades-8Zo/PCI: FPGA id %lx, ver "
+ "%lx\n", (ulong) (0xff &
+ readl(&((struct CUSTOM_REG *)
+ (cy_pci_addr2))->fpga_id)),
+ (ulong)(0xff &
+ readl(&((struct CUSTOM_REG *)
+ (cy_pci_addr2))->
+ fpga_version)));
+ cy_writel(&((struct RUNTIME_9060 *)
+ (cy_pci_addr0))->loc_addr_base,
+ WIN_RAM);
+ } else {
+ printk("Cyclades-Z/PCI: New Cyclades-Z board. "
+ "FPGA not loaded\n");
+ }
#endif
- /* The following clears the firmware id word. This
- ensures that the driver will not attempt to talk to
- the board until it has been properly initialized.
- */
- if ((mailbox == ZO_V1) || (mailbox == ZO_V2))
- cy_writel(cy_pci_addr2 + ID_ADDRESS, 0L);
-
- /* This must be a Cyclades-8Zo/PCI. The extendable
- version will have a different device_id and will
- be allocated its maximum number of ports. */
- cy_pci_nchan = 8;
-
- if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) {
- printk("Cyclades-8Zo/PCI found at 0x%lx but"
- "no channels are available.\nChange "
- "NR_PORTS in cyclades.c and recompile "
- "kernel.\n", (ulong)cy_pci_phys2);
- return i;
- }
+ /* The following clears the firmware id word. This
+ ensures that the driver will not attempt to talk to
+ the board until it has been properly initialized.
+ */
+ if ((mailbox == ZO_V1) || (mailbox == ZO_V2))
+ cy_writel(cy_pci_addr2 + ID_ADDRESS, 0L);
+
+ /* This must be a Cyclades-8Zo/PCI. The extendable
+ version will have a different device_id and will
+ be allocated its maximum number of ports. */
+ cy_pci_nchan = 8;
+
+ if ((cy_next_channel + cy_pci_nchan) > NR_PORTS) {
+ printk("Cyclades-8Zo/PCI found at 0x%lx but"
+ "no channels are available.\nChange "
+ "NR_PORTS in cyclades.c and recompile "
+ "kernel.\n", (ulong)cy_pci_phys2);
+ return -EIO;
+ }
- /* fill the next cy_card structure available */
- for (j = 0; j < NR_CARDS; j++) {
- if (cy_card[j].base_addr == 0)
- break;
- }
- if (j == NR_CARDS) { /* no more cy_cards available */
- printk("Cyclades-8Zo/PCI found at 0x%lx but"
- "no more cards can be used.\nChange "
- "NR_CARDS in cyclades.c and recompile "
- "kernel.\n", (ulong)cy_pci_phys2);
- return i;
- }
+ /* fill the next cy_card structure available */
+ for (j = 0; j < NR_CARDS; j++) {
+ if (cy_card[j].base_addr == 0)
+ break;
+ }
+ if (j == NR_CARDS) { /* no more cy_cards available */
+ printk("Cyclades-8Zo/PCI found at 0x%lx but"
+ "no more cards can be used.\nChange "
+ "NR_CARDS in cyclades.c and recompile "
+ "kernel.\n", (ulong)cy_pci_phys2);
+ return -EIO;
+ }
#ifdef CONFIG_CYZ_INTR
- /* allocate IRQ only if board has an IRQ */
- if ((cy_pci_irq != 0) && (cy_pci_irq != 255)) {
- if (request_irq(cy_pci_irq, cyz_interrupt,
- IRQF_SHARED, "Cyclades-Z",
- &cy_card[j])) {
- printk("Cyclom-8Zo/PCI found at 0x%lx "
- "but could not allocate "
- "IRQ%d.\n", (ulong)cy_pci_phys2,
- cy_pci_irq);
- return i;
- }
+ /* allocate IRQ only if board has an IRQ */
+ if ((cy_pci_irq != 0) && (cy_pci_irq != 255)) {
+ retval = request_irq(cy_pci_irq, cyz_interrupt,
+ IRQF_SHARED, "Cyclades-Z",
+ &cy_card[j]);
+ if (retval) {
+ printk("Cyclom-8Zo/PCI found at 0x%lx "
+ "but could not allocate "
+ "IRQ%d.\n", (ulong)cy_pci_phys2,
+ cy_pci_irq);
+ return retval;
}
+ }
#endif /* CONFIG_CYZ_INTR */
- /* set cy_card */
- cy_card[j].base_phys = cy_pci_phys2;
- cy_card[j].ctl_phys = cy_pci_phys0;
- cy_card[j].base_addr = cy_pci_addr2;
- cy_card[j].ctl_addr = cy_pci_addr0;
- cy_card[j].irq = (int)cy_pci_irq;
- cy_card[j].bus_index = 1;
- cy_card[j].first_line = cy_next_channel;
- cy_card[j].num_chips = -1;
- cy_card[j].pdev = pdev;
- pci_set_drvdata(pdev, &cy_card[j]);
-
- /* print message */
+ /* set cy_card */
+ cy_card[j].base_phys = cy_pci_phys2;
+ cy_card[j].ctl_phys = cy_pci_phys0;
+ cy_card[j].base_addr = cy_pci_addr2;
+ cy_card[j].ctl_addr = cy_pci_addr0;
+ cy_card[j].irq = (int)cy_pci_irq;
+ cy_card[j].bus_index = 1;
+ cy_card[j].first_line = cy_next_channel;
+ cy_card[j].num_chips = -1;
+ cy_card[j].pdev = pdev;
+ pci_set_drvdata(pdev, &cy_card[j]);
+
+ /* print message */
#ifdef CONFIG_CYZ_INTR
- /* don't report IRQ if board is no IRQ */
- if ((cy_pci_irq != 0) && (cy_pci_irq != 255))
- printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, "
- "IRQ%d, ", j + 1, (ulong)cy_pci_phys2,
- (ulong) (cy_pci_phys2 + CyPCI_Zwin - 1),
- (int)cy_pci_irq);
- else
+ /* don't report IRQ if board is no IRQ */
+ if ((cy_pci_irq != 0) && (cy_pci_irq != 255))
+ printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, "
+ "IRQ%d, ", j + 1, (ulong)cy_pci_phys2,
+ (ulong) (cy_pci_phys2 + CyPCI_Zwin - 1),
+ (int)cy_pci_irq);
+ else
#endif /* CONFIG_CYZ_INTR */
- printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, ",
- j + 1, (ulong)cy_pci_phys2,
- (ulong)(cy_pci_phys2 + CyPCI_Zwin - 1));
+ printk("Cyclades-8Zo/PCI #%d: 0x%lx-0x%lx, ",
+ j + 1, (ulong)cy_pci_phys2,
+ (ulong)(cy_pci_phys2 + CyPCI_Zwin - 1));
+
+ printk("%d channels starting from port %d.\n",
+ cy_pci_nchan, cy_next_channel);
+ cy_next_channel += cy_pci_nchan;
+ }
+
+ return 0;
+}
+#endif
+
+/*
+ * ---------------------------------------------------------------------
+ * cy_detect_pci() - Test PCI bus presence and Cyclom-Ye/PCI.
+ * sets global variables and return the number of PCI boards found.
+ * ---------------------------------------------------------------------
+ */
+static int __init cy_detect_pci(void)
+{
+#ifdef CONFIG_PCI
+ struct pci_dev *pdev = NULL;
+ unsigned int i, device_id, dev_index = 0;
- printk("%d channels starting from port %d.\n",
- cy_pci_nchan, cy_next_channel);
- cy_next_channel += cy_pci_nchan;
+ for (i = 0; i < NR_CARDS; i++) {
+ /* look for a Cyclades card by vendor and device id */
+ while ((device_id = cy_pci_dev_id[dev_index].device) != 0) {
+ if ((pdev = pci_get_device(PCI_VENDOR_ID_CYCLADES,
+ device_id, pdev)) == NULL) {
+ dev_index++; /* try next device id */
+ } else {
+ break; /* found a board */
+ }
}
+
+ if (device_id == 0)
+ break;
+
+ i -= !!cy_pci_probe(pdev, &cy_pci_dev_id[dev_index]);
}
return i;
projects / openwrt / staging / blogic.git / commitdiff