net: Add documentation for VRF device

Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/Documentation/networking/vrf.txt b/Documentation/networking/vrf.txt
new file mode 100644 (file)
index 0000000..031ef4a
--- /dev/null
+++ b/Documentation/networking/vrf.txt
@@ -0,0 +1,96 @@
+Virtual Routing and Forwarding (VRF)
+====================================
+The VRF device combined with ip rules provides the ability to create virtual
+routing and forwarding domains (aka VRFs, VRF-lite to be specific) in the
+Linux network stack. One use case is the multi-tenancy problem where each
+tenant has their own unique routing tables and in the very least need
+different default gateways.
+
+Processes can be "VRF aware" by binding a socket to the VRF device. Packets
+through the socket then use the routing table associated with the VRF
+device. An important feature of the VRF device implementation is that it
+impacts only Layer 3 and above so L2 tools (e.g., LLDP) are not affected
+(ie., they do not need to be run in each VRF). The design also allows
+the use of higher priority ip rules (Policy Based Routing, PBR) to take
+precedence over the VRF device rules directing specific traffic as desired.
+
+In addition, VRF devices allow VRFs to be nested within namespaces. For
+example network namespaces provide separation of network interfaces at L1
+(Layer 1 separation), VLANs on the interfaces within a namespace provide
+L2 separation and then VRF devices provide L3 separation.
+
+Design
+------
+A VRF device is created with an associated route table. Network interfaces
+are then enslaved to a VRF device:
+
+         +-----------------------------+
+         |           vrf-blue          |  ===> route table 10
+         +-----------------------------+
+            |        |            |
+         +------+ +------+     +-------------+
+         | eth1 | | eth2 | ... |    bond1    |
+         +------+ +------+     +-------------+
+                                  |       |
+                              +------+ +------+
+                              | eth8 | | eth9 |
+                              +------+ +------+
+
+Packets received on an enslaved device and are switched to the VRF device
+using an rx_handler which gives the impression that packets flow through
+the VRF device. Similarly on egress routing rules are used to send packets
+to the VRF device driver before getting sent out the actual interface. This
+allows tcpdump on a VRF device to capture all packets into and out of the
+VRF as a whole.[1] Similiarly, netfilter [2] and tc rules can be applied
+using the VRF device to specify rules that apply to the VRF domain as a whole.
+
+[1] Packets in the forwarded state do not flow through the device, so those
+    packets are not seen by tcpdump. Will revisit this limitation in a
+    future release.
+
+[2] Iptables on ingress is limited to NF_INET_PRE_ROUTING only with skb->dev
+    set to real ingress device and egress is limited to NF_INET_POST_ROUTING.
+    Will revisit this limitation in a future release.
+
+
+Setup
+-----
+1. VRF device is created with an association to a FIB table.
+   e.g, ip link add vrf-blue type vrf table 10
+        ip link set dev vrf-blue up
+
+2. Rules are added that send lookups to the associated FIB table when the
+   iif or oif is the VRF device. e.g.,
+       ip ru add oif vrf-blue table 10
+       ip ru add iif vrf-blue table 10
+
+   Set the default route for the table (and hence default route for the VRF).
+   e.g, ip route add table 10 prohibit default
+
+3. Enslave L3 interfaces to a VRF device.
+   e.g,  ip link set dev eth1 master vrf-blue
+
+   Local and connected routes for enslaved devices are automatically moved to
+   the table associated with VRF device. Any additional routes depending on
+   the enslaved device will need to be reinserted following the enslavement.
+
+4. Additional VRF routes are added to associated table.
+   e.g., ip route add table 10 ...
+
+
+Applications
+------------
+Applications that are to work within a VRF need to bind their socket to the
+VRF device:
+
+    setsockopt(sd, SOL_SOCKET, SO_BINDTODEVICE, dev, strlen(dev)+1);
+
+or to specify the output device using cmsg and IP_PKTINFO.
+
+
+Limitations
+-----------
+VRF device currently only works for IPv4. Support for IPv6 is under development.
+
+Index of original ingress interface is not available via cmsg. Will address
+soon.

diff --git a/MAINTAINERS b/MAINTAINERS
index 310da4295c7026e27698e9f8b980adcc1893b774..d4d9d4f6d271867b72046a4b3e866ed7057b9894 100644 (file)
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11243,6 +11243,7 @@ L:      netdev@vger.kernel.org
 S:     Maintained
 F:     drivers/net/vrf.c
 F:     include/net/vrf.h
+F:     Documentation/networking/vrf.txt
 
 VT1211 HARDWARE MONITOR DRIVER
 M:     Juerg Haefliger <juergh@gmail.com>