Port device support for Meraki MR12 from the ar71xx target to ath79.
Specifications:
- SoC: AR7242-AH1A CPU
- RAM: 64MiB (NANYA NT5DS32M16DS-5T)
- NOR Flash: 16MiB (MXIC MX25L12845EMI-10G)
- Ethernet: 1 x PoE Gigabit Ethernet Port (SoC MAC + AR8021-BL1E PHY)
- Ethernet: 1 x 100Mbit port (SoC MAC+PHY)
- Wi-Fi: Atheros AR9283-AL1A (2T2R, 11n)
Installation:
1. Requires TFTP server at 192.168.1.101, w/ initramfs & sysupgrade .bins
2. Open shell case
3. Connect a USB->TTL cable to headers furthest from the RF shield
4. Power on the router; connect to U-boot over 115200-baud connection
5. Interrupt U-boot process to boot Openwrt by running:
setenv bootcmd bootm 0xbf0a0000; saveenv;
tftpboot
0c00000 <filename-of-initramfs-kernel>.bin;
bootm
0c00000;
6. Copy sysupgrade image to /tmp on MR12
7. sysupgrade /tmp/<filename-of-sysupgrade>.bin
Notes:
- kmod-owl-loader is still required to load the ART partition into the
driver.
- The manner of storing MAC addresses is updated from ar71xx; it is
at 0x66 of the 'config' partition, where it was discovered that the
OEM firmware stores it. This is set as read-only. If you are
migrating from ar71xx and used the method mentioned above to
upgrade, use kmod-mtd-rw or UCI to add the MAC back in. One more
method for doing this is described below.
- Migrating directly from ar71xx has not been thoroughly tested, but
one method has been used a couple of times with good success,
migrating 18.06.2 to a full image produced as of this commit. Please
note that these instructions are only for experienced users, and/or
those still able to open their device up to flash it via the serial
headers should anything go wrong.
1) Install kmod-mtd-rw and uboot-envtools
2) Run `insmod mtd-rw.ko i_want_a_brick=1`
3) Modify /etc/fw_env.config to point to the u-boot-env partition.
The file /etc/fw_env.config should contain:
# MTD device env offset env size sector size
/dev/mtd1 0x00000 0x10000 0x10000
See https://openwrt.org/docs/techref/bootloader/uboot.config
for more details.
4) Run `fw_printenv` to verify everything is correct, as per the
link above.
5) Run `fw_setenv bootcmd bootm 0xbf0a0000` to set a new boot address.
6) Manually modify /lib/upgrade/common.sh's get_image function:
Change ...
cat "$from" 2>/dev/null | $cmd
... into ...
(
dd if=/dev/zero bs=1 count=$((0x66)) ; # Pad the first 102 bytes
echo -ne '\x00\x18\x0a\x12\x34\x56' ; # Add in MAC address
dd if=/dev/zero bs=1 count=$((0x20000-0x66-0x6)) ; # Pad the rest
cat "$from" 2>/dev/null
) | $cmd
... which, during the upgrade process, will pad the image by
128K of zeroes-plus-MAC-address, in order for the ar71xx's
firmware partition -- which starts at 0xbf080000 -- to be
instead aligned with the ath79 firmware partition, which
starts 128K later at 0xbf0a0000.
7) Copy the sysupgrade image into /tmp, as above
8) Run `sysupgrade -F /tmp/<sysupgrade>.bin`, then wait
Again, this may BRICK YOUR DEVICE, so make *sure* to have your
serial cable handy.
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[add LED migration and extend compat message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "ar7242.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "meraki,mr12", "qca,ar7242";
+ model = "Meraki MR12";
+
+ aliases {
+ led-boot = &led_power_orange;
+ led-failsafe = &led_power_orange;
+ led-running = &led_power_green;
+ led-upgrade = &led_power_orange;
+ };
+
+ extosc: ref {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-output-names = "ref";
+ clock-frequency = <40000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ link1 {
+ label = "green:link1";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ link2 {
+ label = "green:link2";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ link3 {
+ label = "green:link3";
+ gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ link4 {
+ label = "green:link4";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ lan {
+ label = "green:lan";
+ gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
+ };
+
+ led_power_orange: power_orange {
+ label = "orange:power";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ panic-indicator;
+ };
+
+ led_power_green: power_green {
+ label = "green:power";
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+
+ wifi@0,0,0 {
+ compatible = "pci168c,002a";
+ reg = <0x0000 0 0 0 0>;
+ qca,no-eeprom;
+ mtd-mac-address = <&config 0x66>;
+ mtd-mac-address-increment = <1>;
+ };
+};
+
+&pll {
+ clocks = <&extosc>;
+};
+
+&uart {
+ status = "okay";
+};
+
+&mdio0 {
+ status = "okay";
+
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ mtd-mac-address = <&config 0x66>;
+
+ pll-data = <0x02000000 0x00000101 0x00001313>;
+
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy4>;
+};
+
+&mdio1 {
+ status = "okay";
+};
+
+ð1 {
+ status = "okay";
+
+ mtd-mac-address = <&config 0x66>;
+};
+
+&spi {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x40000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "u-boot-env";
+ reg = <0x40000 0x40000>;
+ read-only;
+ };
+
+ config: partition@80000 {
+ label = "config";
+ reg = <0x80000 0x20000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "firmware";
+ reg = <0xa0000 0xf40000>;
+ compatible = "denx,uimage";
+ };
+
+ partition@fe0000 {
+ label = "art";
+ reg = <0xfe0000 0x20000>;
+ read-only;
+ };
+ };
+ };
+};
hak5,lan-turtle)
ucidef_set_led_netdev "wan" "WAN" "orange:system" "eth1"
;;
+meraki,mr12|\
+tplink,cpe210-v2|\
+tplink,cpe210-v3)
+ ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0"
+ ucidef_set_rssimon "wlan0" "200000" "1"
+ ucidef_set_led_rssi "rssilow" "RSSILOW" "green:link1" "wlan0" "1" "100"
+ ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "green:link2" "wlan0" "30" "100"
+ ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "green:link3" "wlan0" "60" "100"
+ ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "green:link4" "wlan0" "80" "100"
+ ;;
meraki,mr16)
ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth0"
;;
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "green:link3" "wlan0" "60" "100"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "green:link4" "wlan0" "80" "100"
;;
-tplink,cpe210-v2|\
-tplink,cpe210-v3)
- ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0"
- ucidef_set_rssimon "wlan0" "200000" "1"
- ucidef_set_led_rssi "rssilow" "RSSILOW" "green:link1" "wlan0" "1" "100"
- ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "green:link2" "wlan0" "30" "100"
- ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "green:link3" "wlan0" "60" "100"
- ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "green:link4" "wlan0" "80" "100"
- ;;
tplink,cpe510-v2|\
tplink,cpe510-v3)
ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth0"
ucidef_add_switch "switch0" \
"0@eth0" "5:wan" "6@eth1" "4:lan"
;;
+ meraki,mr12)
+ ucidef_set_interface_lan "eth0"
+ ucidef_add_switch "switch0" \
+ "0@eth1" "1:lan"
+ ;;
mercury,mw4530r-v1|\
tplink,archer-a7-v5|\
tplink,archer-c6-v2|\
caldata_extract "calibrate" 0x1000 0x440
ath9k_patch_mac $(mtd_get_mac_ascii u-boot-env0 RADIOADDR1)
;;
+ meraki,mr12)
+ caldata_extract "art" 0x11000 0xeb8
+ ;;
nec,wg800hp)
caldata_extract "art" 0x1000 0x440
ath9k_patch_mac $(mtd_get_mac_text board_data 0x680)
glinet,gl-mifi)
migrate_leds ":net=:3g4g"
;;
+meraki,mr12)
+ migrate_leds ":wifi=:link" ":wan=:lan"
+ ;;
openmesh,mr600-v1)
migrate_leds ":wlan58=:wifi5g"
;;
. /lib/functions.sh
case "$(board_name)" in
+ meraki,mr12|\
meraki,mr16)
uci set system.@system[0].compat_version="2.0"
uci commit system
endef
TARGET_DEVICES += librerouter_librerouter-v1
+define Device/meraki_mr12
+ SOC := ar7242
+ DEVICE_VENDOR := Meraki
+ DEVICE_MODEL := MR12
+ IMAGE_SIZE := 15616k
+ DEVICE_PACKAGES := kmod-owl-loader rssileds
+ SUPPORTED_DEVICES += mr12
+ DEVICE_COMPAT_VERSION := 2.0
+ DEVICE_COMPAT_MESSAGE := Partitions differ from ar71xx version of MR12. Image format is incompatible. \
+ To use sysupgrade, you must change /lib/update/common.sh::get_image to prepend 128K zeroes to this image, \
+ and change the bootcmd in u-boot to "bootm 0xbf0a0000". After that, you can use "sysupgrade -F -n". \
+ Make sure you do not keep your old config, as ethernet setup is not compatible either. \
+ For more details, see the OpenWrt Wiki: https://openwrt.org/toh/meraki/MR12, \
+ or the commit message of the MR12 ath79 port on git.openwrt.org.
+endef
+TARGET_DEVICES += meraki_mr12
+
define Device/meraki_mr16
SOC := ar7161
DEVICE_VENDOR := Meraki
projects / openwrt / staging / stintel.git / commitdiff