#include <linux/types.h>
+#define NL80211_GENL_NAME "nl80211"
+
/**
* DOC: Station handling
*
* The station is still assumed to belong to the AP interface it was added
* to.
*
- * TODO: need more info?
+ * Station handling varies per interface type and depending on the driver's
+ * capabilities.
+ *
+ * For drivers supporting TDLS with external setup (WIPHY_FLAG_SUPPORTS_TDLS
+ * and WIPHY_FLAG_TDLS_EXTERNAL_SETUP), the station lifetime is as follows:
+ * - a setup station entry is added, not yet authorized, without any rate
+ * or capability information, this just exists to avoid race conditions
+ * - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid
+ * to add rate and capability information to the station and at the same
+ * time mark it authorized.
+ * - %NL80211_TDLS_ENABLE_LINK is then used
+ * - after this, the only valid operation is to remove it by tearing down
+ * the TDLS link (%NL80211_TDLS_DISABLE_LINK)
+ *
+ * TODO: need more info for other interface types
*/
/**
* interfaces that a given device supports.
*/
+/**
+ * DOC: packet coalesce support
+ *
+ * In most cases, host that receives IPv4 and IPv6 multicast/broadcast
+ * packets does not do anything with these packets. Therefore the
+ * reception of these unwanted packets causes unnecessary processing
+ * and power consumption.
+ *
+ * Packet coalesce feature helps to reduce number of received interrupts
+ * to host by buffering these packets in firmware/hardware for some
+ * predefined time. Received interrupt will be generated when one of the
+ * following events occur.
+ * a) Expiration of hardware timer whose expiration time is set to maximum
+ * coalescing delay of matching coalesce rule.
+ * b) Coalescing buffer in hardware reaches it's limit.
+ * c) Packet doesn't match any of the configured coalesce rules.
+ *
+ * User needs to configure following parameters for creating a coalesce
+ * rule.
+ * a) Maximum coalescing delay
+ * b) List of packet patterns which needs to be matched
+ * c) Condition for coalescence. pattern 'match' or 'no match'
+ * Multiple such rules can be created.
+ */
+
/**
* enum nl80211_commands - supported nl80211 commands
*
* to get a list of all present wiphys.
* @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or
* %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME,
- * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ,
- * %NL80211_ATTR_WIPHY_CHANNEL_TYPE, %NL80211_ATTR_WIPHY_RETRY_SHORT,
+ * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ (and the
+ * attributes determining the channel width; this is used for setting
+ * monitor mode channel), %NL80211_ATTR_WIPHY_RETRY_SHORT,
* %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
* and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD.
* However, for setting the channel, see %NL80211_CMD_SET_CHANNEL
* @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_IDX
* or %NL80211_ATTR_MAC.
*
- * @NL80211_CMD_GET_BEACON: retrieve beacon information (returned in a
- * %NL80222_CMD_NEW_BEACON message)
- * @NL80211_CMD_SET_BEACON: set the beacon on an access point interface
- * using the %NL80211_ATTR_BEACON_INTERVAL, %NL80211_ATTR_DTIM_PERIOD,
- * %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL attributes.
- * Following attributes are provided for drivers that generate full Beacon
- * and Probe Response frames internally: %NL80211_ATTR_SSID,
+ * @NL80211_CMD_GET_BEACON: (not used)
+ * @NL80211_CMD_SET_BEACON: change the beacon on an access point interface
+ * using the %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL
+ * attributes. For drivers that generate the beacon and probe responses
+ * internally, the following attributes must be provided: %NL80211_ATTR_IE,
+ * %NL80211_ATTR_IE_PROBE_RESP and %NL80211_ATTR_IE_ASSOC_RESP.
+ * @NL80211_CMD_START_AP: Start AP operation on an AP interface, parameters
+ * are like for %NL80211_CMD_SET_BEACON, and additionally parameters that
+ * do not change are used, these include %NL80211_ATTR_BEACON_INTERVAL,
+ * %NL80211_ATTR_DTIM_PERIOD, %NL80211_ATTR_SSID,
* %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE,
* %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS,
* %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY,
- * %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_IE, %NL80211_ATTR_IE_PROBE_RESP,
- * %NL80211_ATTR_IE_ASSOC_RESP.
- * @NL80211_CMD_NEW_BEACON: add a new beacon to an access point interface,
- * parameters are like for %NL80211_CMD_SET_BEACON.
- * @NL80211_CMD_DEL_BEACON: remove the beacon, stop sending it
+ * %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_INACTIVITY_TIMEOUT,
+ * %NL80211_ATTR_ACL_POLICY and %NL80211_ATTR_MAC_ADDRS.
+ * The channel to use can be set on the interface or be given using the
+ * %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel width.
+ * @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP
+ * @NL80211_CMD_STOP_AP: Stop AP operation on the given interface
+ * @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP
*
* @NL80211_CMD_GET_STATION: Get station attributes for station identified by
* %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX.
* passed, all channels allowed for the current regulatory domain
* are used. Extra IEs can also be passed from the userspace by
* using the %NL80211_ATTR_IE attribute.
- * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT
- * if scheduled scan is not running.
+ * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT if
+ * scheduled scan is not running. The caller may assume that as soon
+ * as the call returns, it is safe to start a new scheduled scan again.
* @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan
* results available.
* @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has
* @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
* NL80211_CMD_GET_SURVEY and on the "scan" multicast group)
*
+ * @NL80211_CMD_SET_PMKSA: Add a PMKSA cache entry, using %NL80211_ATTR_MAC
+ * (for the BSSID) and %NL80211_ATTR_PMKID.
+ * @NL80211_CMD_DEL_PMKSA: Delete a PMKSA cache entry, using %NL80211_ATTR_MAC
+ * (for the BSSID) and %NL80211_ATTR_PMKID.
+ * @NL80211_CMD_FLUSH_PMKSA: Flush all PMKSA cache entries.
+ *
* @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain
* has been changed and provides details of the request information
* that caused the change such as who initiated the regulatory request
* requests to connect to a specified network but without separating
* auth and assoc steps. For this, you need to specify the SSID in a
* %NL80211_ATTR_SSID attribute, and can optionally specify the association
- * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC,
- * %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
- * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE and
- * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT.
+ * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP,
+ * %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
+ * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
+ * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT, %NL80211_ATTR_MAC_HINT, and
+ * %NL80211_ATTR_WIPHY_FREQ_HINT.
+ * If included, %NL80211_ATTR_MAC and %NL80211_ATTR_WIPHY_FREQ are
+ * restrictions on BSS selection, i.e., they effectively prevent roaming
+ * within the ESS. %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT
+ * can be included to provide a recommendation of the initial BSS while
+ * allowing the driver to roam to other BSSes within the ESS and also to
+ * ignore this recommendation if the indicated BSS is not ideal. Only one
+ * set of BSSID,frequency parameters is used (i.e., either the enforcing
+ * %NL80211_ATTR_MAC,%NL80211_ATTR_WIPHY_FREQ or the less strict
+ * %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT).
+ * Background scan period can optionally be
+ * specified in %NL80211_ATTR_BG_SCAN_PERIOD,
+ * if not specified default background scan configuration
+ * in driver is used and if period value is 0, bg scan will be disabled.
+ * This attribute is ignored if driver does not support roam scan.
* It is also sent as an event, with the BSSID and response IEs when the
* connection is established or failed to be established. This can be
* determined by the STATUS_CODE attribute.
* a response while being associated to an AP on another channel.
* %NL80211_ATTR_IFINDEX is used to specify which interface (and thus
* radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
- * frequency for the operation and %NL80211_ATTR_WIPHY_CHANNEL_TYPE may be
- * optionally used to specify additional channel parameters.
+ * frequency for the operation.
* %NL80211_ATTR_DURATION is used to specify the duration in milliseconds
* to remain on the channel. This command is also used as an event to
* notify when the requested duration starts (it may take a while for the
* as an event indicating reception of a frame that was not processed in
* kernel code, but is for us (i.e., which may need to be processed in a
* user space application). %NL80211_ATTR_FRAME is used to specify the
- * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and
- * optionally %NL80211_ATTR_WIPHY_CHANNEL_TYPE) is used to indicate on
- * which channel the frame is to be transmitted or was received. If this
- * channel is not the current channel (remain-on-channel or the
- * operational channel) the device will switch to the given channel and
- * transmit the frame, optionally waiting for a response for the time
+ * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ is used
+ * to indicate on which channel the frame is to be transmitted or was
+ * received. If this channel is not the current channel (remain-on-channel
+ * or the operational channel) the device will switch to the given channel
+ * and transmit the frame, optionally waiting for a response for the time
* specified using %NL80211_ATTR_DURATION. When called, this operation
* returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the
* TX status event pertaining to the TX request.
* %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
* management frames at CCK rate or not in 2GHz band.
+ * %NL80211_ATTR_CSA_C_OFFSETS_TX is an array of offsets to CSA
+ * counters which will be updated to the current value. This attribute
+ * is used during CSA period.
* @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
* command may be used with the corresponding cookie to cancel the wait
* time if it is known that it is no longer necessary.
* the frame.
* @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for
* backward compatibility.
+ *
+ * @NL80211_CMD_SET_POWER_SAVE: Set powersave, using %NL80211_ATTR_PS_STATE
+ * @NL80211_CMD_GET_POWER_SAVE: Get powersave status in %NL80211_ATTR_PS_STATE
+ *
* @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command
* is used to configure connection quality monitoring notification trigger
* levels.
* command is used as an event to indicate the that a trigger level was
* reached.
* @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
- * and %NL80211_ATTR_WIPHY_CHANNEL_TYPE) the given interface (identifed
- * by %NL80211_ATTR_IFINDEX) shall operate on.
+ * and the attributes determining channel width) the given interface
+ * (identifed by %NL80211_ATTR_IFINDEX) shall operate on.
* In case multiple channels are supported by the device, the mechanism
* with which it switches channels is implementation-defined.
* When a monitor interface is given, it can only switch channel while
* @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a
* beacon or probe response from a compatible mesh peer. This is only
* sent while no station information (sta_info) exists for the new peer
- * candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH is set. On
- * reception of this notification, userspace may decide to create a new
- * station (@NL80211_CMD_NEW_STATION). To stop this notification from
+ * candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH,
+ * @NL80211_MESH_SETUP_USERSPACE_AMPE, or
+ * @NL80211_MESH_SETUP_USERSPACE_MPM is set. On reception of this
+ * notification, userspace may decide to create a new station
+ * (@NL80211_CMD_NEW_STATION). To stop this notification from
* reoccurring, the userspace authentication daemon may want to create the
* new station with the AUTHENTICATED flag unset and maybe change it later
* depending on the authentication result.
* command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For
* more background information, see
* http://wireless.kernel.org/en/users/Documentation/WoWLAN.
+ * The @NL80211_CMD_SET_WOWLAN command can also be used as a notification
+ * from the driver reporting the wakeup reason. In this case, the
+ * @NL80211_ATTR_WOWLAN_TRIGGERS attribute will contain the reason
+ * for the wakeup, if it was caused by wireless. If it is not present
+ * in the wakeup notification, the wireless device didn't cause the
+ * wakeup but reports that it was woken up.
*
* @NL80211_CMD_SET_REKEY_OFFLOAD: This command is used give the driver
* the necessary information for supporting GTK rekey offload. This
* of PMKSA caching dandidates.
*
* @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
- * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame.
+ * In addition, this can be used as an event to request userspace to take
+ * actions on TDLS links (set up a new link or tear down an existing one).
+ * In such events, %NL80211_ATTR_TDLS_OPERATION indicates the requested
+ * operation, %NL80211_ATTR_MAC contains the peer MAC address, and
+ * %NL80211_ATTR_REASON_CODE the reason code to be used (only with
+ * %NL80211_TDLS_TEARDOWN).
+ * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. The
+ * %NL80211_ATTR_TDLS_ACTION attribute determines the type of frame to be
+ * sent. Public Action codes (802.11-2012 8.1.5.1) will be sent as
+ * 802.11 management frames, while TDLS action codes (802.11-2012
+ * 8.5.13.1) will be encapsulated and sent as data frames. The currently
+ * supported Public Action code is %WLAN_PUB_ACTION_TDLS_DISCOVER_RES
+ * and the currently supported TDLS actions codes are given in
+ * &enum ieee80211_tdls_actioncode.
*
* @NL80211_CMD_UNEXPECTED_FRAME: Used by an application controlling an AP
* (or GO) interface (i.e. hostapd) to ask for unexpected frames to
* @NL80211_CMD_SET_NOACK_MAP: sets a bitmap for the individual TIDs whether
* No Acknowledgement Policy should be applied.
*
+ * @NL80211_CMD_CH_SWITCH_NOTIFY: An AP or GO may decide to switch channels
+ * independently of the userspace SME, send this event indicating
+ * %NL80211_ATTR_IFINDEX is now on %NL80211_ATTR_WIPHY_FREQ and the
+ * attributes determining channel width.
+ *
+ * @NL80211_CMD_START_P2P_DEVICE: Start the given P2P Device, identified by
+ * its %NL80211_ATTR_WDEV identifier. It must have been created with
+ * %NL80211_CMD_NEW_INTERFACE previously. After it has been started, the
+ * P2P Device can be used for P2P operations, e.g. remain-on-channel and
+ * public action frame TX.
+ * @NL80211_CMD_STOP_P2P_DEVICE: Stop the given P2P Device, identified by
+ * its %NL80211_ATTR_WDEV identifier.
+ *
+ * @NL80211_CMD_CONN_FAILED: connection request to an AP failed; used to
+ * notify userspace that AP has rejected the connection request from a
+ * station, due to particular reason. %NL80211_ATTR_CONN_FAILED_REASON
+ * is used for this.
+ *
+ * @NL80211_CMD_SET_MCAST_RATE: Change the rate used to send multicast frames
+ * for IBSS or MESH vif.
+ *
+ * @NL80211_CMD_SET_MAC_ACL: sets ACL for MAC address based access control.
+ * This is to be used with the drivers advertising the support of MAC
+ * address based access control. List of MAC addresses is passed in
+ * %NL80211_ATTR_MAC_ADDRS and ACL policy is passed in
+ * %NL80211_ATTR_ACL_POLICY. Driver will enable ACL with this list, if it
+ * is not already done. The new list will replace any existing list. Driver
+ * will clear its ACL when the list of MAC addresses passed is empty. This
+ * command is used in AP/P2P GO mode. Driver has to make sure to clear its
+ * ACL list during %NL80211_CMD_STOP_AP.
+ *
+ * @NL80211_CMD_RADAR_DETECT: Start a Channel availability check (CAC). Once
+ * a radar is detected or the channel availability scan (CAC) has finished
+ * or was aborted, or a radar was detected, usermode will be notified with
+ * this event. This command is also used to notify userspace about radars
+ * while operating on this channel.
+ * %NL80211_ATTR_RADAR_EVENT is used to inform about the type of the
+ * event.
+ *
+ * @NL80211_CMD_GET_PROTOCOL_FEATURES: Get global nl80211 protocol features,
+ * i.e. features for the nl80211 protocol rather than device features.
+ * Returns the features in the %NL80211_ATTR_PROTOCOL_FEATURES bitmap.
+ *
+ * @NL80211_CMD_UPDATE_FT_IES: Pass down the most up-to-date Fast Transition
+ * Information Element to the WLAN driver
+ *
+ * @NL80211_CMD_FT_EVENT: Send a Fast transition event from the WLAN driver
+ * to the supplicant. This will carry the target AP's MAC address along
+ * with the relevant Information Elements. This event is used to report
+ * received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE).
+ *
+ * @NL80211_CMD_CRIT_PROTOCOL_START: Indicates user-space will start running
+ * a critical protocol that needs more reliability in the connection to
+ * complete.
+ *
+ * @NL80211_CMD_CRIT_PROTOCOL_STOP: Indicates the connection reliability can
+ * return back to normal.
+ *
+ * @NL80211_CMD_GET_COALESCE: Get currently supported coalesce rules.
+ * @NL80211_CMD_SET_COALESCE: Configure coalesce rules or clear existing rules.
+ *
+ * @NL80211_CMD_CHANNEL_SWITCH: Perform a channel switch by announcing the
+ * the new channel information (Channel Switch Announcement - CSA)
+ * in the beacon for some time (as defined in the
+ * %NL80211_ATTR_CH_SWITCH_COUNT parameter) and then change to the
+ * new channel. Userspace provides the new channel information (using
+ * %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel
+ * width). %NL80211_ATTR_CH_SWITCH_BLOCK_TX may be supplied to inform
+ * other station that transmission must be blocked until the channel
+ * switch is complete.
+ *
+ * @NL80211_CMD_VENDOR: Vendor-specified command/event. The command is specified
+ * by the %NL80211_ATTR_VENDOR_ID attribute and a sub-command in
+ * %NL80211_ATTR_VENDOR_SUBCMD. Parameter(s) can be transported in
+ * %NL80211_ATTR_VENDOR_DATA.
+ * For feature advertisement, the %NL80211_ATTR_VENDOR_DATA attribute is
+ * used in the wiphy data as a nested attribute containing descriptions
+ * (&struct nl80211_vendor_cmd_info) of the supported vendor commands.
+ * This may also be sent as an event with the same attributes.
+ *
+ * @NL80211_CMD_SET_QOS_MAP: Set Interworking QoS mapping for IP DSCP values.
+ * The QoS mapping information is included in %NL80211_ATTR_QOS_MAP. If
+ * that attribute is not included, QoS mapping is disabled. Since this
+ * QoS mapping is relevant for IP packets, it is only valid during an
+ * association. This is cleared on disassociation and AP restart.
+ *
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
NL80211_CMD_GET_BEACON,
NL80211_CMD_SET_BEACON,
- NL80211_CMD_NEW_BEACON,
- NL80211_CMD_DEL_BEACON,
+ NL80211_CMD_START_AP,
+ NL80211_CMD_NEW_BEACON = NL80211_CMD_START_AP,
+ NL80211_CMD_STOP_AP,
+ NL80211_CMD_DEL_BEACON = NL80211_CMD_STOP_AP,
NL80211_CMD_GET_STATION,
NL80211_CMD_SET_STATION,
NL80211_CMD_SET_NOACK_MAP,
+ NL80211_CMD_CH_SWITCH_NOTIFY,
+
+ NL80211_CMD_START_P2P_DEVICE,
+ NL80211_CMD_STOP_P2P_DEVICE,
+
+ NL80211_CMD_CONN_FAILED,
+
+ NL80211_CMD_SET_MCAST_RATE,
+
+ NL80211_CMD_SET_MAC_ACL,
+
+ NL80211_CMD_RADAR_DETECT,
+
+ NL80211_CMD_GET_PROTOCOL_FEATURES,
+
+ NL80211_CMD_UPDATE_FT_IES,
+ NL80211_CMD_FT_EVENT,
+
+ NL80211_CMD_CRIT_PROTOCOL_START,
+ NL80211_CMD_CRIT_PROTOCOL_STOP,
+
+ NL80211_CMD_GET_COALESCE,
+ NL80211_CMD_SET_COALESCE,
+
+ NL80211_CMD_CHANNEL_SWITCH,
+
+ NL80211_CMD_VENDOR,
+
+ NL80211_CMD_SET_QOS_MAP,
+
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
* /sys/class/ieee80211/<phyname>/index
* @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming)
* @NL80211_ATTR_WIPHY_TXQ_PARAMS: a nested array of TX queue parameters
- * @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz
+ * @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz,
+ * defines the channel together with the (deprecated)
+ * %NL80211_ATTR_WIPHY_CHANNEL_TYPE attribute or the attributes
+ * %NL80211_ATTR_CHANNEL_WIDTH and if needed %NL80211_ATTR_CENTER_FREQ1
+ * and %NL80211_ATTR_CENTER_FREQ2
+ * @NL80211_ATTR_CHANNEL_WIDTH: u32 attribute containing one of the values
+ * of &enum nl80211_chan_width, describing the channel width. See the
+ * documentation of the enum for more information.
+ * @NL80211_ATTR_CENTER_FREQ1: Center frequency of the first part of the
+ * channel, used for anything but 20 MHz bandwidth
+ * @NL80211_ATTR_CENTER_FREQ2: Center frequency of the second part of the
+ * channel, used only for 80+80 MHz bandwidth
* @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ
- * if HT20 or HT40 are allowed (i.e., 802.11n disabled if not included):
+ * if HT20 or HT40 are to be used (i.e., HT disabled if not included):
* NL80211_CHAN_NO_HT = HT not allowed (i.e., same as not including
* this attribute)
* NL80211_CHAN_HT20 = HT20 only
* NL80211_CHAN_HT40MINUS = secondary channel is below the primary channel
* NL80211_CHAN_HT40PLUS = secondary channel is above the primary channel
+ * This attribute is now deprecated.
* @NL80211_ATTR_WIPHY_RETRY_SHORT: TX retry limit for frames whose length is
* less than or equal to the RTS threshold; allowed range: 1..255;
* dot11ShortRetryLimit; u8
* @NL80211_ATTR_IFNAME: network interface name
* @NL80211_ATTR_IFTYPE: type of virtual interface, see &enum nl80211_iftype
*
+ * @NL80211_ATTR_WDEV: wireless device identifier, used for pseudo-devices
+ * that don't have a netdev (u64)
+ *
* @NL80211_ATTR_MAC: MAC address (various uses)
*
* @NL80211_ATTR_KEY_DATA: (temporal) key data; for TKIP this consists of
* section 7.3.2.25.1, e.g. 0x000FAC04)
* @NL80211_ATTR_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and
* CCMP keys, each six bytes in little endian
+ * @NL80211_ATTR_KEY_DEFAULT: Flag attribute indicating the key is default key
+ * @NL80211_ATTR_KEY_DEFAULT_MGMT: Flag attribute indicating the key is the
+ * default management key
+ * @NL80211_ATTR_CIPHER_SUITES_PAIRWISE: For crypto settings for connect or
+ * other commands, indicates which pairwise cipher suites are used
+ * @NL80211_ATTR_CIPHER_SUITE_GROUP: For crypto settings for connect or
+ * other commands, indicates which group cipher suite is used
*
* @NL80211_ATTR_BEACON_INTERVAL: beacon interval in TU
* @NL80211_ATTR_DTIM_PERIOD: DTIM period for beaconing
* consisting of a nested array.
*
* @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes).
- * @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link.
+ * @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link
+ * (see &enum nl80211_plink_action).
* @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path.
* @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path
* info given for %NL80211_CMD_GET_MPATH, nested attribute described at
* to query the CRDA to retrieve one regulatory domain. This attribute can
* also be used by userspace to query the kernel for the currently set
* regulatory domain. We chose an alpha2 as that is also used by the
- * IEEE-802.11d country information element to identify a country.
+ * IEEE-802.11 country information element to identify a country.
* Users can also simply ask the wireless core to set regulatory domain
* to a specific alpha2.
* @NL80211_ATTR_REG_RULES: a nested array of regulatory domain regulatory
* @NL80211_ATTR_USE_MFP: Whether management frame protection (IEEE 802.11w) is
* used for the association (&enum nl80211_mfp, represented as a u32);
* this attribute can be used
- * with %NL80211_CMD_ASSOCIATE request
+ * with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests
*
* @NL80211_ATTR_STA_FLAGS2: Attribute containing a
* &struct nl80211_sta_flag_update.
* @NL80211_ATTR_ACK: Flag attribute indicating that the frame was
* acknowledged by the recipient.
*
+ * @NL80211_ATTR_PS_STATE: powersave state, using &enum nl80211_ps_state values.
+ *
* @NL80211_ATTR_CQM: connection quality monitor configuration in a
* nested attribute with %NL80211_ATTR_CQM_* sub-attributes.
*
* flag isn't set, the frame will be rejected. This is also used as an
* nl80211 capability flag.
*
- * @NL80211_ATTR_BSS_HTOPMODE: HT operation mode (u16)
+ * @NL80211_ATTR_BSS_HT_OPMODE: HT operation mode (u16)
*
* @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags
* attributes, specifying what a key should be set as default as.
* @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver
* allows auth frames in a mesh to be passed to userspace for processing via
* the @NL80211_MESH_SETUP_USERSPACE_AUTH flag.
- * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as
- * defined in &enum nl80211_plink_state. Used when userspace is
- * driving the peer link management state machine.
- * @NL80211_MESH_SETUP_USERSPACE_AMPE must be enabled.
+ * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as defined in
+ * &enum nl80211_plink_state. Used when userspace is driving the peer link
+ * management state machine. @NL80211_MESH_SETUP_USERSPACE_AMPE or
+ * @NL80211_MESH_SETUP_USERSPACE_MPM must be enabled.
*
* @NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED: indicates, as part of the wiphy
* capabilities, the supported WoWLAN triggers
* indicate which WoW triggers should be enabled. This is also
* used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN
* triggers.
-
+ *
* @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan
* cycles, in msecs.
-
+ *
* @NL80211_ATTR_SCHED_SCAN_MATCH: Nested attribute with one or more
* sets of attributes to match during scheduled scans. Only BSSs
* that match any of the sets will be reported. These are
* are managed in software: interfaces of these types aren't subject to
* any restrictions in their number or combinations.
*
- * @%NL80211_ATTR_REKEY_DATA: nested attribute containing the information
+ * @NL80211_ATTR_REKEY_DATA: nested attribute containing the information
* necessary for GTK rekeying in the device, see &enum nl80211_rekey_data.
*
* @NL80211_ATTR_SCAN_SUPP_RATES: rates per to be advertised as supported in scan,
* @NL80211_ATTR_FEATURE_FLAGS: This u32 attribute contains flags from
* &enum nl80211_feature_flags and is advertised in wiphy information.
* @NL80211_ATTR_PROBE_RESP_OFFLOAD: Indicates that the HW responds to probe
- *
* requests while operating in AP-mode.
* This attribute holds a bitmap of the supported protocols for
* offloading (see &enum nl80211_probe_resp_offload_support_attr).
* @NL80211_ATTR_NOACK_MAP: This u16 bitmap contains the No Ack Policy of
* up to 16 TIDs.
*
+ * @NL80211_ATTR_INACTIVITY_TIMEOUT: timeout value in seconds, this can be
+ * used by the drivers which has MLME in firmware and does not have support
+ * to report per station tx/rx activity to free up the staion entry from
+ * the list. This needs to be used when the driver advertises the
+ * capability to timeout the stations.
+ *
+ * @NL80211_ATTR_RX_SIGNAL_DBM: signal strength in dBm (as a 32-bit int);
+ * this attribute is (depending on the driver capabilities) added to
+ * received frames indicated with %NL80211_CMD_FRAME.
+ *
+ * @NL80211_ATTR_BG_SCAN_PERIOD: Background scan period in seconds
+ * or 0 to disable background scan.
+ *
+ * @NL80211_ATTR_USER_REG_HINT_TYPE: type of regulatory hint passed from
+ * userspace. If unset it is assumed the hint comes directly from
+ * a user. If set code could specify exactly what type of source
+ * was used to provide the hint. For the different types of
+ * allowed user regulatory hints see nl80211_user_reg_hint_type.
+ *
+ * @NL80211_ATTR_CONN_FAILED_REASON: The reason for which AP has rejected
+ * the connection request from a station. nl80211_connect_failed_reason
+ * enum has different reasons of connection failure.
+ *
+ * @NL80211_ATTR_SAE_DATA: SAE elements in Authentication frames. This starts
+ * with the Authentication transaction sequence number field.
+ *
+ * @NL80211_ATTR_VHT_CAPABILITY: VHT Capability information element (from
+ * association request when used with NL80211_CMD_NEW_STATION)
+ *
+ * @NL80211_ATTR_SCAN_FLAGS: scan request control flags (u32)
+ *
+ * @NL80211_ATTR_P2P_CTWINDOW: P2P GO Client Traffic Window (u8), used with
+ * the START_AP and SET_BSS commands
+ * @NL80211_ATTR_P2P_OPPPS: P2P GO opportunistic PS (u8), used with the
+ * START_AP and SET_BSS commands. This can have the values 0 or 1;
+ * if not given in START_AP 0 is assumed, if not given in SET_BSS
+ * no change is made.
+ *
+ * @NL80211_ATTR_LOCAL_MESH_POWER_MODE: local mesh STA link-specific power mode
+ * defined in &enum nl80211_mesh_power_mode.
+ *
+ * @NL80211_ATTR_ACL_POLICY: ACL policy, see &enum nl80211_acl_policy,
+ * carried in a u32 attribute
+ *
+ * @NL80211_ATTR_MAC_ADDRS: Array of nested MAC addresses, used for
+ * MAC ACL.
+ *
+ * @NL80211_ATTR_MAC_ACL_MAX: u32 attribute to advertise the maximum
+ * number of MAC addresses that a device can support for MAC
+ * ACL.
+ *
+ * @NL80211_ATTR_RADAR_EVENT: Type of radar event for notification to userspace,
+ * contains a value of enum nl80211_radar_event (u32).
+ *
+ * @NL80211_ATTR_EXT_CAPA: 802.11 extended capabilities that the kernel driver
+ * has and handles. The format is the same as the IE contents. See
+ * 802.11-2012 8.4.2.29 for more information.
+ * @NL80211_ATTR_EXT_CAPA_MASK: Extended capabilities that the kernel driver
+ * has set in the %NL80211_ATTR_EXT_CAPA value, for multibit fields.
+ *
+ * @NL80211_ATTR_STA_CAPABILITY: Station capabilities (u16) are advertised to
+ * the driver, e.g., to enable TDLS power save (PU-APSD).
+ *
+ * @NL80211_ATTR_STA_EXT_CAPABILITY: Station extended capabilities are
+ * advertised to the driver, e.g., to enable TDLS off channel operations
+ * and PU-APSD.
+ *
+ * @NL80211_ATTR_PROTOCOL_FEATURES: global nl80211 feature flags, see
+ * &enum nl80211_protocol_features, the attribute is a u32.
+ *
+ * @NL80211_ATTR_SPLIT_WIPHY_DUMP: flag attribute, userspace supports
+ * receiving the data for a single wiphy split across multiple
+ * messages, given with wiphy dump message
+ *
+ * @NL80211_ATTR_MDID: Mobility Domain Identifier
+ *
+ * @NL80211_ATTR_IE_RIC: Resource Information Container Information
+ * Element
+ *
+ * @NL80211_ATTR_CRIT_PROT_ID: critical protocol identifier requiring increased
+ * reliability, see &enum nl80211_crit_proto_id (u16).
+ * @NL80211_ATTR_MAX_CRIT_PROT_DURATION: duration in milliseconds in which
+ * the connection should have increased reliability (u16).
+ *
+ * @NL80211_ATTR_PEER_AID: Association ID for the peer TDLS station (u16).
+ * This is similar to @NL80211_ATTR_STA_AID but with a difference of being
+ * allowed to be used with the first @NL80211_CMD_SET_STATION command to
+ * update a TDLS peer STA entry.
+ *
+ * @NL80211_ATTR_COALESCE_RULE: Coalesce rule information.
+ *
+ * @NL80211_ATTR_CH_SWITCH_COUNT: u32 attribute specifying the number of TBTT's
+ * until the channel switch event.
+ * @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission
+ * must be blocked on the current channel (before the channel switch
+ * operation).
+ * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
+ * for the time while performing a channel switch.
+ * @NL80211_ATTR_CSA_C_OFF_BEACON: An array of offsets (u16) to the channel
+ * switch counters in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
+ * @NL80211_ATTR_CSA_C_OFF_PRESP: An array of offsets (u16) to the channel
+ * switch counters in the probe response (%NL80211_ATTR_PROBE_RESP).
+ *
+ * @NL80211_ATTR_RXMGMT_FLAGS: flags for nl80211_send_mgmt(), u32.
+ * As specified in the &enum nl80211_rxmgmt_flags.
+ *
+ * @NL80211_ATTR_STA_SUPPORTED_CHANNELS: array of supported channels.
+ *
+ * @NL80211_ATTR_STA_SUPPORTED_OPER_CLASSES: array of supported
+ * supported operating classes.
+ *
+ * @NL80211_ATTR_HANDLE_DFS: A flag indicating whether user space
+ * controls DFS operation in IBSS mode. If the flag is included in
+ * %NL80211_CMD_JOIN_IBSS request, the driver will allow use of DFS
+ * channels and reports radar events to userspace. Userspace is required
+ * to react to radar events, e.g. initiate a channel switch or leave the
+ * IBSS network.
+ *
+ * @NL80211_ATTR_SUPPORT_5_MHZ: A flag indicating that the device supports
+ * 5 MHz channel bandwidth.
+ * @NL80211_ATTR_SUPPORT_10_MHZ: A flag indicating that the device supports
+ * 10 MHz channel bandwidth.
+ *
+ * @NL80211_ATTR_OPMODE_NOTIF: Operating mode field from Operating Mode
+ * Notification Element based on association request when used with
+ * %NL80211_CMD_NEW_STATION; u8 attribute.
+ *
+ * @NL80211_ATTR_VENDOR_ID: The vendor ID, either a 24-bit OUI or, if
+ * %NL80211_VENDOR_ID_IS_LINUX is set, a special Linux ID (not used yet)
+ * @NL80211_ATTR_VENDOR_SUBCMD: vendor sub-command
+ * @NL80211_ATTR_VENDOR_DATA: data for the vendor command, if any; this
+ * attribute is also used for vendor command feature advertisement
+ * @NL80211_ATTR_VENDOR_EVENTS: used for event list advertising in the wiphy
+ * info, containing a nested array of possible events
+ *
+ * @NL80211_ATTR_QOS_MAP: IP DSCP mapping for Interworking QoS mapping. This
+ * data is in the format defined for the payload of the QoS Map Set element
+ * in IEEE Std 802.11-2012, 8.4.2.97.
+ *
+ * @NL80211_ATTR_MAC_HINT: MAC address recommendation as initial BSS
+ * @NL80211_ATTR_WIPHY_FREQ_HINT: frequency of the recommended initial BSS
+ *
+ * @NL80211_ATTR_MAX_AP_ASSOC_STA: Device attribute that indicates how many
+ * associated stations are supported in AP mode (including P2P GO); u32.
+ * Since drivers may not have a fixed limit on the maximum number (e.g.,
+ * other concurrent operations may affect this), drivers are allowed to
+ * advertise values that cannot always be met. In such cases, an attempt
+ * to add a new station entry with @NL80211_CMD_NEW_STATION may fail.
+ *
+ * @NL80211_ATTR_CSA_C_OFFSETS_TX: An array of csa counter offsets (u16) which
+ * should be updated when the frame is transmitted.
+ * @NL80211_ATTR_MAX_CSA_COUNTERS: U8 attribute used to advertise the maximum
+ * supported number of csa counters.
+ *
+ * @NL80211_ATTR_TDLS_PEER_CAPABILITY: flags for TDLS peer capabilities, u32.
+ * As specified in the &enum nl80211_tdls_peer_capability.
+ *
+ * @NL80211_ATTR_IFACE_SOCKET_OWNER: flag attribute, if set during interface
+ * creation then the new interface will be owned by the netlink socket
+ * that created it and will be destroyed when the socket is closed
+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_GAIN: Configured antenna gain. Used to reduce
+ * transmit power to stay within regulatory limits. u32, dBi.
+ *
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
*/
NL80211_ATTR_NOACK_MAP,
+ NL80211_ATTR_INACTIVITY_TIMEOUT,
+
+ NL80211_ATTR_RX_SIGNAL_DBM,
+
+ NL80211_ATTR_BG_SCAN_PERIOD,
+
+ NL80211_ATTR_WDEV,
+
+ NL80211_ATTR_USER_REG_HINT_TYPE,
+
+ NL80211_ATTR_CONN_FAILED_REASON,
+
+ NL80211_ATTR_SAE_DATA,
+
+ NL80211_ATTR_VHT_CAPABILITY,
+
+ NL80211_ATTR_SCAN_FLAGS,
+
+ NL80211_ATTR_CHANNEL_WIDTH,
+ NL80211_ATTR_CENTER_FREQ1,
+ NL80211_ATTR_CENTER_FREQ2,
+
+ NL80211_ATTR_P2P_CTWINDOW,
+ NL80211_ATTR_P2P_OPPPS,
+
+ NL80211_ATTR_LOCAL_MESH_POWER_MODE,
+
+ NL80211_ATTR_ACL_POLICY,
+
+ NL80211_ATTR_MAC_ADDRS,
+
+ NL80211_ATTR_MAC_ACL_MAX,
+
+ NL80211_ATTR_RADAR_EVENT,
+
+ NL80211_ATTR_EXT_CAPA,
+ NL80211_ATTR_EXT_CAPA_MASK,
+
+ NL80211_ATTR_STA_CAPABILITY,
+ NL80211_ATTR_STA_EXT_CAPABILITY,
+
+ NL80211_ATTR_PROTOCOL_FEATURES,
+ NL80211_ATTR_SPLIT_WIPHY_DUMP,
+
+ NL80211_ATTR_DISABLE_VHT,
+ NL80211_ATTR_VHT_CAPABILITY_MASK,
+
+ NL80211_ATTR_MDID,
+ NL80211_ATTR_IE_RIC,
+
+ NL80211_ATTR_CRIT_PROT_ID,
+ NL80211_ATTR_MAX_CRIT_PROT_DURATION,
+
+ NL80211_ATTR_PEER_AID,
+
+ NL80211_ATTR_COALESCE_RULE,
+
+ NL80211_ATTR_CH_SWITCH_COUNT,
+ NL80211_ATTR_CH_SWITCH_BLOCK_TX,
+ NL80211_ATTR_CSA_IES,
+ NL80211_ATTR_CSA_C_OFF_BEACON,
+ NL80211_ATTR_CSA_C_OFF_PRESP,
+
+ NL80211_ATTR_RXMGMT_FLAGS,
+
+ NL80211_ATTR_STA_SUPPORTED_CHANNELS,
+
+ NL80211_ATTR_STA_SUPPORTED_OPER_CLASSES,
+
+ NL80211_ATTR_HANDLE_DFS,
+
+ NL80211_ATTR_SUPPORT_5_MHZ,
+ NL80211_ATTR_SUPPORT_10_MHZ,
+
+ NL80211_ATTR_OPMODE_NOTIF,
+
+ NL80211_ATTR_VENDOR_ID,
+ NL80211_ATTR_VENDOR_SUBCMD,
+ NL80211_ATTR_VENDOR_DATA,
+ NL80211_ATTR_VENDOR_EVENTS,
+
+ NL80211_ATTR_QOS_MAP,
+
+ NL80211_ATTR_MAC_HINT,
+ NL80211_ATTR_WIPHY_FREQ_HINT,
+
+ NL80211_ATTR_MAX_AP_ASSOC_STA,
+
+ NL80211_ATTR_TDLS_PEER_CAPABILITY,
+
+ NL80211_ATTR_IFACE_SOCKET_OWNER,
+
+ NL80211_ATTR_CSA_C_OFFSETS_TX,
+ NL80211_ATTR_MAX_CSA_COUNTERS,
+
+ NL80211_ATTR_WIPHY_ANTENNA_GAIN,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
#define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY 16
#define NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY 24
#define NL80211_HT_CAPABILITY_LEN 26
+#define NL80211_VHT_CAPABILITY_LEN 12
#define NL80211_MAX_NR_CIPHER_SUITES 5
#define NL80211_MAX_NR_AKM_SUITES 2
+#define NL80211_MIN_REMAIN_ON_CHANNEL_TIME 10
+
+/* default RSSI threshold for scan results if none specified. */
+#define NL80211_SCAN_RSSI_THOLD_OFF -300
+
+#define NL80211_CQM_TXE_MAX_INTVL 1800
+
/**
* enum nl80211_iftype - (virtual) interface types
*
* @NL80211_IFTYPE_MESH_POINT: mesh point
* @NL80211_IFTYPE_P2P_CLIENT: P2P client
* @NL80211_IFTYPE_P2P_GO: P2P group owner
+ * @NL80211_IFTYPE_P2P_DEVICE: P2P device interface type, this is not a netdev
+ * and therefore can't be created in the normal ways, use the
+ * %NL80211_CMD_START_P2P_DEVICE and %NL80211_CMD_STOP_P2P_DEVICE
+ * commands to create and destroy one
* @NL80211_IFTYPE_MAX: highest interface type number currently defined
* @NUM_NL80211_IFTYPES: number of defined interface types
*
NL80211_IFTYPE_MESH_POINT,
NL80211_IFTYPE_P2P_CLIENT,
NL80211_IFTYPE_P2P_GO,
+ NL80211_IFTYPE_P2P_DEVICE,
/* keep last */
NUM_NL80211_IFTYPES,
* flag can't be changed, it is only valid while adding a station, and
* attempts to change it will silently be ignored (rather than rejected
* as errors.)
+ * @NL80211_STA_FLAG_ASSOCIATED: station is associated; used with drivers
+ * that support %NL80211_FEATURE_FULL_AP_CLIENT_STATE to transition a
+ * previously added station into associated state
* @NL80211_STA_FLAG_MAX: highest station flag number currently defined
* @__NL80211_STA_FLAG_AFTER_LAST: internal use
*/
NL80211_STA_FLAG_MFP,
NL80211_STA_FLAG_AUTHENTICATED,
NL80211_STA_FLAG_TDLS_PEER,
+ NL80211_STA_FLAG_ASSOCIATED,
/* keep last */
__NL80211_STA_FLAG_AFTER_LAST,
NL80211_STA_FLAG_MAX = __NL80211_STA_FLAG_AFTER_LAST - 1
};
+#define NL80211_STA_FLAG_MAX_OLD_API NL80211_STA_FLAG_TDLS_PEER
+
/**
* struct nl80211_sta_flag_update - station flags mask/set
* @mask: mask of station flags to set
*
* These attribute types are used with %NL80211_STA_INFO_TXRATE
* when getting information about the bitrate of a station.
+ * There are 2 attributes for bitrate, a legacy one that represents
+ * a 16-bit value, and new one that represents a 32-bit value.
+ * If the rate value fits into 16 bit, both attributes are reported
+ * with the same value. If the rate is too high to fit into 16 bits
+ * (>6.5535Gbps) only 32-bit attribute is included.
+ * User space tools encouraged to use the 32-bit attribute and fall
+ * back to the 16-bit one for compatibility with older kernels.
*
* @__NL80211_RATE_INFO_INVALID: attribute number 0 is reserved
* @NL80211_RATE_INFO_BITRATE: total bitrate (u16, 100kbit/s)
* @NL80211_RATE_INFO_MCS: mcs index for 802.11n (u8)
- * @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 Mhz dualchannel bitrate
+ * @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 MHz dualchannel bitrate
* @NL80211_RATE_INFO_SHORT_GI: 400ns guard interval
+ * @NL80211_RATE_INFO_BITRATE32: total bitrate (u32, 100kbit/s)
* @NL80211_RATE_INFO_MAX: highest rate_info number currently defined
+ * @NL80211_RATE_INFO_VHT_MCS: MCS index for VHT (u8)
+ * @NL80211_RATE_INFO_VHT_NSS: number of streams in VHT (u8)
+ * @NL80211_RATE_INFO_80_MHZ_WIDTH: 80 MHz VHT rate
+ * @NL80211_RATE_INFO_80P80_MHZ_WIDTH: 80+80 MHz VHT rate
+ * @NL80211_RATE_INFO_160_MHZ_WIDTH: 160 MHz VHT rate
* @__NL80211_RATE_INFO_AFTER_LAST: internal use
*/
enum nl80211_rate_info {
NL80211_RATE_INFO_MCS,
NL80211_RATE_INFO_40_MHZ_WIDTH,
NL80211_RATE_INFO_SHORT_GI,
+ NL80211_RATE_INFO_BITRATE32,
+ NL80211_RATE_INFO_VHT_MCS,
+ NL80211_RATE_INFO_VHT_NSS,
+ NL80211_RATE_INFO_80_MHZ_WIDTH,
+ NL80211_RATE_INFO_80P80_MHZ_WIDTH,
+ NL80211_RATE_INFO_160_MHZ_WIDTH,
/* keep last */
__NL80211_RATE_INFO_AFTER_LAST,
* @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs)
* @NL80211_STA_INFO_RX_BYTES: total received bytes (u32, from this station)
* @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (u32, to this station)
+ * @NL80211_STA_INFO_RX_BYTES64: total received bytes (u64, from this station)
+ * @NL80211_STA_INFO_TX_BYTES64: total transmitted bytes (u64, to this station)
* @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm)
* @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute
* containing info as possible, see &enum nl80211_rate_info
* @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected
* @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update.
* @NL80211_STA_INFO_BEACON_LOSS: count of times beacon loss was detected (u32)
+ * @NL80211_STA_INFO_T_OFFSET: timing offset with respect to this STA (s64)
+ * @NL80211_STA_INFO_LOCAL_PM: local mesh STA link-specific power mode
+ * @NL80211_STA_INFO_PEER_PM: peer mesh STA link-specific power mode
+ * @NL80211_STA_INFO_NONPEER_PM: neighbor mesh STA power save mode towards
+ * non-peer STA
* @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU
+ * Contains a nested array of signal strength attributes (u8, dBm)
* @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
+ * Same format as NL80211_STA_INFO_CHAIN_SIGNAL.
+ * @NL80211_STA_EXPECTED_THROUGHPUT: expected throughput considering also the
+ * 802.11 header (u32, kbps)
* @__NL80211_STA_INFO_AFTER_LAST: internal
* @NL80211_STA_INFO_MAX: highest possible station info attribute
*/
NL80211_STA_INFO_CONNECTED_TIME,
NL80211_STA_INFO_STA_FLAGS,
NL80211_STA_INFO_BEACON_LOSS,
+ NL80211_STA_INFO_T_OFFSET,
+ NL80211_STA_INFO_LOCAL_PM,
+ NL80211_STA_INFO_PEER_PM,
+ NL80211_STA_INFO_NONPEER_PM,
+ NL80211_STA_INFO_RX_BYTES64,
+ NL80211_STA_INFO_TX_BYTES64,
NL80211_STA_INFO_CHAIN_SIGNAL,
NL80211_STA_INFO_CHAIN_SIGNAL_AVG,
+ NL80211_STA_INFO_EXPECTED_THROUGHPUT,
/* keep last */
__NL80211_STA_INFO_AFTER_LAST,
* @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE
* @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n
* @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n
+ * @NL80211_BAND_ATTR_VHT_MCS_SET: 32-byte attribute containing the MCS set as
+ * defined in 802.11ac
+ * @NL80211_BAND_ATTR_VHT_CAPA: VHT capabilities, as in the HT information IE
* @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
* @__NL80211_BAND_ATTR_AFTER_LAST: internal use
*/
NL80211_BAND_ATTR_HT_AMPDU_FACTOR,
NL80211_BAND_ATTR_HT_AMPDU_DENSITY,
+ NL80211_BAND_ATTR_VHT_MCS_SET,
+ NL80211_BAND_ATTR_VHT_CAPA,
+
/* keep last */
__NL80211_BAND_ATTR_AFTER_LAST,
NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1
* @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz
* @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current
* regulatory domain.
- * @NL80211_FREQUENCY_ATTR_PASSIVE_SCAN: Only passive scanning is
- * permitted on this channel in current regulatory domain.
- * @NL80211_FREQUENCY_ATTR_NO_IBSS: IBSS networks are not permitted
- * on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_NO_IR: no mechanisms that initiate radiation
+ * are permitted on this channel, this includes sending probe
+ * requests, or modes of operation that require beaconing.
* @NL80211_FREQUENCY_ATTR_RADAR: Radar detection is mandatory
* on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm
* (100 * dBm).
+ * @NL80211_FREQUENCY_ATTR_DFS_STATE: current state for DFS
+ * (enum nl80211_dfs_state)
+ * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in miliseconds for how long
+ * this channel is in this DFS state.
+ * @NL80211_FREQUENCY_ATTR_NO_HT40_MINUS: HT40- isn't possible with this
+ * channel as the control channel
+ * @NL80211_FREQUENCY_ATTR_NO_HT40_PLUS: HT40+ isn't possible with this
+ * channel as the control channel
+ * @NL80211_FREQUENCY_ATTR_NO_80MHZ: any 80 MHz channel using this channel
+ * as the primary or any of the secondary channels isn't possible,
+ * this includes 80+80 channels
+ * @NL80211_FREQUENCY_ATTR_NO_160MHZ: any 160 MHz (but not 80+80) channel
+ * using this channel as the primary or any of the secondary channels
+ * isn't possible
+ * @NL80211_FREQUENCY_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
+ * @NL80211_FREQUENCY_ATTR_INDOOR_ONLY: Only indoor use is permitted on this
+ * channel. A channel that has the INDOOR_ONLY attribute can only be
+ * used when there is a clear assessment that the device is operating in
+ * an indoor surroundings, i.e., it is connected to AC power (and not
+ * through portable DC inverters) or is under the control of a master
+ * that is acting as an AP and is connected to AC power.
+ * @NL80211_FREQUENCY_ATTR_GO_CONCURRENT: GO operation is allowed on this
+ * channel if it's connected concurrently to a BSS on the same channel on
+ * the 2 GHz band or to a channel in the same UNII band (on the 5 GHz
+ * band), and IEEE80211_CHAN_RADAR is not set. Instantiating a GO on a
+ * channel that has the GO_CONCURRENT attribute set can be done when there
+ * is a clear assessment that the device is operating under the guidance of
+ * an authorized master, i.e., setting up a GO while the device is also
+ * connected to an AP with DFS and radar detection on the UNII band (it is
+ * up to user-space, i.e., wpa_supplicant to perform the required
+ * verifications)
+ * @NL80211_FREQUENCY_ATTR_NO_20MHZ: 20 MHz operation is not allowed
+ * on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_NO_10MHZ: 10 MHz operation is not allowed
+ * on this channel in current regulatory domain.
* @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
* currently defined
* @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
+ *
+ * See https://apps.fcc.gov/eas/comments/GetPublishedDocument.html?id=327&tn=528122
+ * for more information on the FCC description of the relaxations allowed
+ * by NL80211_FREQUENCY_ATTR_INDOOR_ONLY and
+ * NL80211_FREQUENCY_ATTR_GO_CONCURRENT.
*/
enum nl80211_frequency_attr {
__NL80211_FREQUENCY_ATTR_INVALID,
NL80211_FREQUENCY_ATTR_FREQ,
NL80211_FREQUENCY_ATTR_DISABLED,
- NL80211_FREQUENCY_ATTR_PASSIVE_SCAN,
- NL80211_FREQUENCY_ATTR_NO_IBSS,
+ NL80211_FREQUENCY_ATTR_NO_IR,
+ __NL80211_FREQUENCY_ATTR_NO_IBSS,
NL80211_FREQUENCY_ATTR_RADAR,
NL80211_FREQUENCY_ATTR_MAX_TX_POWER,
+ NL80211_FREQUENCY_ATTR_DFS_STATE,
+ NL80211_FREQUENCY_ATTR_DFS_TIME,
+ NL80211_FREQUENCY_ATTR_NO_HT40_MINUS,
+ NL80211_FREQUENCY_ATTR_NO_HT40_PLUS,
+ NL80211_FREQUENCY_ATTR_NO_80MHZ,
+ NL80211_FREQUENCY_ATTR_NO_160MHZ,
+ NL80211_FREQUENCY_ATTR_DFS_CAC_TIME,
+ NL80211_FREQUENCY_ATTR_INDOOR_ONLY,
+ NL80211_FREQUENCY_ATTR_GO_CONCURRENT,
+ NL80211_FREQUENCY_ATTR_NO_20MHZ,
+ NL80211_FREQUENCY_ATTR_NO_10MHZ,
/* keep last */
__NL80211_FREQUENCY_ATTR_AFTER_LAST,
};
#define NL80211_FREQUENCY_ATTR_MAX_TX_POWER NL80211_FREQUENCY_ATTR_MAX_TX_POWER
+#define NL80211_FREQUENCY_ATTR_PASSIVE_SCAN NL80211_FREQUENCY_ATTR_NO_IR
+#define NL80211_FREQUENCY_ATTR_NO_IBSS NL80211_FREQUENCY_ATTR_NO_IR
+#define NL80211_FREQUENCY_ATTR_NO_IR NL80211_FREQUENCY_ATTR_NO_IR
/**
* enum nl80211_bitrate_attr - bitrate attributes
* in KHz. This is not a center a frequency but an actual regulatory
* band edge.
* @NL80211_ATTR_FREQ_RANGE_MAX_BW: maximum allowed bandwidth for this
- * frequency range, in KHz.
+ * frequency range, in KHz.
* @NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN: the maximum allowed antenna gain
* for a given frequency range. The value is in mBi (100 * dBi).
* If you don't have one then don't send this.
* @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for
* a given frequency range. The value is in mBm (100 * dBm).
+ * @NL80211_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
+ * If not present or 0 default CAC time will be used.
* @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
* currently defined
* @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use
NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN,
NL80211_ATTR_POWER_RULE_MAX_EIRP,
+ NL80211_ATTR_DFS_CAC_TIME,
+
/* keep last */
__NL80211_REG_RULE_ATTR_AFTER_LAST,
NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1
* enum nl80211_sched_scan_match_attr - scheduled scan match attributes
* @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved
* @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching,
- * only report BSS with matching SSID.
+ * only report BSS with matching SSID.
+ * @NL80211_SCHED_SCAN_MATCH_ATTR_RSSI: RSSI threshold (in dBm) for reporting a
+ * BSS in scan results. Filtering is turned off if not specified. Note that
+ * if this attribute is in a match set of its own, then it is treated as
+ * the default value for all matchsets with an SSID, rather than being a
+ * matchset of its own without an RSSI filter. This is due to problems with
+ * how this API was implemented in the past. Also, due to the same problem,
+ * the only way to create a matchset with only an RSSI filter (with this
+ * attribute) is if there's only a single matchset with the RSSI attribute.
* @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter
* attribute number currently defined
* @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use
enum nl80211_sched_scan_match_attr {
__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID,
- NL80211_ATTR_SCHED_SCAN_MATCH_SSID,
+ NL80211_SCHED_SCAN_MATCH_ATTR_SSID,
+ NL80211_SCHED_SCAN_MATCH_ATTR_RSSI,
/* keep last */
__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST,
__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST - 1
};
+/* only for backward compatibility */
+#define NL80211_ATTR_SCHED_SCAN_MATCH_SSID NL80211_SCHED_SCAN_MATCH_ATTR_SSID
+
/**
* enum nl80211_reg_rule_flags - regulatory rule flags
*
* @NL80211_RRF_DFS: DFS support is required to be used
* @NL80211_RRF_PTP_ONLY: this is only for Point To Point links
* @NL80211_RRF_PTMP_ONLY: this is only for Point To Multi Point links
- * @NL80211_RRF_PASSIVE_SCAN: passive scan is required
- * @NL80211_RRF_NO_IBSS: no IBSS is allowed
+ * @NL80211_RRF_NO_IR: no mechanisms that initiate radiation are allowed,
+ * this includes probe requests or modes of operation that require
+ * beaconing.
+ * @NL80211_RRF_AUTO_BW: maximum available bandwidth should be calculated
+ * base on contiguous rules and wider channels will be allowed to cross
+ * multiple contiguous/overlapping frequency ranges.
*/
enum nl80211_reg_rule_flags {
NL80211_RRF_NO_OFDM = 1<<0,
NL80211_RRF_DFS = 1<<4,
NL80211_RRF_PTP_ONLY = 1<<5,
NL80211_RRF_PTMP_ONLY = 1<<6,
- NL80211_RRF_PASSIVE_SCAN = 1<<7,
- NL80211_RRF_NO_IBSS = 1<<8,
+ NL80211_RRF_NO_IR = 1<<7,
+ __NL80211_RRF_NO_IBSS = 1<<8,
+ NL80211_RRF_AUTO_BW = 1<<11,
};
+#define NL80211_RRF_PASSIVE_SCAN NL80211_RRF_NO_IR
+#define NL80211_RRF_NO_IBSS NL80211_RRF_NO_IR
+#define NL80211_RRF_NO_IR NL80211_RRF_NO_IR
+
+/* For backport compatibility with older userspace */
+#define NL80211_RRF_NO_IR_ALL (NL80211_RRF_NO_IR | __NL80211_RRF_NO_IBSS)
+
/**
* enum nl80211_dfs_regions - regulatory DFS regions
*
* @NL80211_DFS_UNSET: Country has no DFS master region specified
- * @NL80211_DFS_FCC_: Country follows DFS master rules from FCC
- * @NL80211_DFS_FCC_: Country follows DFS master rules from ETSI
- * @NL80211_DFS_JP_: Country follows DFS master rules from JP/MKK/Telec
+ * @NL80211_DFS_FCC: Country follows DFS master rules from FCC
+ * @NL80211_DFS_ETSI: Country follows DFS master rules from ETSI
+ * @NL80211_DFS_JP: Country follows DFS master rules from JP/MKK/Telec
*/
enum nl80211_dfs_regions {
NL80211_DFS_UNSET = 0,
NL80211_DFS_JP = 3,
};
+/**
+ * enum nl80211_user_reg_hint_type - type of user regulatory hint
+ *
+ * @NL80211_USER_REG_HINT_USER: a user sent the hint. This is always
+ * assumed if the attribute is not set.
+ * @NL80211_USER_REG_HINT_CELL_BASE: the hint comes from a cellular
+ * base station. Device drivers that have been tested to work
+ * properly to support this type of hint can enable these hints
+ * by setting the NL80211_FEATURE_CELL_BASE_REG_HINTS feature
+ * capability on the struct wiphy. The wireless core will
+ * ignore all cell base station hints until at least one device
+ * present has been registered with the wireless core that
+ * has listed NL80211_FEATURE_CELL_BASE_REG_HINTS as a
+ * supported feature.
+ * @NL80211_USER_REG_HINT_INDOOR: a user sent an hint indicating that the
+ * platform is operating in an indoor environment.
+ */
+enum nl80211_user_reg_hint_type {
+ NL80211_USER_REG_HINT_USER = 0,
+ NL80211_USER_REG_HINT_CELL_BASE = 1,
+ NL80211_USER_REG_HINT_INDOOR = 2,
+};
+
/**
* enum nl80211_survey_info - survey information
*
* @NL80211_MNTR_FLAG_OTHER_BSS: disable BSSID filtering
* @NL80211_MNTR_FLAG_COOK_FRAMES: report frames after processing.
* overrides all other flags.
+ * @NL80211_MNTR_FLAG_ACTIVE: use the configured MAC address
+ * and ACK incoming unicast packets.
*
* @__NL80211_MNTR_FLAG_AFTER_LAST: internal use
* @NL80211_MNTR_FLAG_MAX: highest possible monitor flag
NL80211_MNTR_FLAG_CONTROL,
NL80211_MNTR_FLAG_OTHER_BSS,
NL80211_MNTR_FLAG_COOK_FRAMES,
+ NL80211_MNTR_FLAG_ACTIVE,
/* keep last */
__NL80211_MNTR_FLAG_AFTER_LAST,
NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1
};
+/**
+ * enum nl80211_mesh_power_mode - mesh power save modes
+ *
+ * @NL80211_MESH_POWER_UNKNOWN: The mesh power mode of the mesh STA is
+ * not known or has not been set yet.
+ * @NL80211_MESH_POWER_ACTIVE: Active mesh power mode. The mesh STA is
+ * in Awake state all the time.
+ * @NL80211_MESH_POWER_LIGHT_SLEEP: Light sleep mode. The mesh STA will
+ * alternate between Active and Doze states, but will wake up for
+ * neighbor's beacons.
+ * @NL80211_MESH_POWER_DEEP_SLEEP: Deep sleep mode. The mesh STA will
+ * alternate between Active and Doze states, but may not wake up
+ * for neighbor's beacons.
+ *
+ * @__NL80211_MESH_POWER_AFTER_LAST - internal use
+ * @NL80211_MESH_POWER_MAX - highest possible power save level
+ */
+
+enum nl80211_mesh_power_mode {
+ NL80211_MESH_POWER_UNKNOWN,
+ NL80211_MESH_POWER_ACTIVE,
+ NL80211_MESH_POWER_LIGHT_SLEEP,
+ NL80211_MESH_POWER_DEEP_SLEEP,
+
+ __NL80211_MESH_POWER_AFTER_LAST,
+ NL80211_MESH_POWER_MAX = __NL80211_MESH_POWER_AFTER_LAST - 1
+};
+
/**
* enum nl80211_meshconf_params - mesh configuration parameters
*
* @__NL80211_MESHCONF_INVALID: internal use
*
* @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in
- * millisecond units, used by the Peer Link Open message
+ * millisecond units, used by the Peer Link Open message
*
* @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the initial confirm timeout, in
- * millisecond units, used by the peer link management to close a peer link
+ * millisecond units, used by the peer link management to close a peer link
*
* @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in
- * millisecond units
+ * millisecond units
*
* @NL80211_MESHCONF_MAX_PEER_LINKS: maximum number of peer links allowed
- * on this mesh interface
+ * on this mesh interface
*
* @NL80211_MESHCONF_MAX_RETRIES: specifies the maximum number of peer link
- * open retries that can be sent to establish a new peer link instance in a
- * mesh
+ * open retries that can be sent to establish a new peer link instance in a
+ * mesh
*
* @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh
- * point.
+ * point.
*
- * @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically
- * open peer links when we detect compatible mesh peers.
+ * @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically open
+ * peer links when we detect compatible mesh peers. Disabled if
+ * @NL80211_MESH_SETUP_USERSPACE_MPM or @NL80211_MESH_SETUP_USERSPACE_AMPE are
+ * set.
*
* @NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES: the number of action frames
- * containing a PREQ that an MP can send to a particular destination (path
- * target)
+ * containing a PREQ that an MP can send to a particular destination (path
+ * target)
*
* @NL80211_MESHCONF_PATH_REFRESH_TIME: how frequently to refresh mesh paths
- * (in milliseconds)
+ * (in milliseconds)
*
* @NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT: minimum length of time to wait
- * until giving up on a path discovery (in milliseconds)
+ * until giving up on a path discovery (in milliseconds)
*
* @NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT: The time (in TUs) for which mesh
- * points receiving a PREQ shall consider the forwarding information from the
- * root to be valid. (TU = time unit)
+ * points receiving a PREQ shall consider the forwarding information from
+ * the root to be valid. (TU = time unit)
*
* @NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL: The minimum interval of time (in
- * TUs) during which an MP can send only one action frame containing a PREQ
- * reference element
+ * TUs) during which an MP can send only one action frame containing a PREQ
+ * reference element
*
* @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs)
- * that it takes for an HWMP information element to propagate across the mesh
+ * that it takes for an HWMP information element to propagate across the
+ * mesh
*
* @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not
*
* @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a
- * source mesh point for path selection elements.
+ * source mesh point for path selection elements.
*
* @NL80211_MESHCONF_HWMP_RANN_INTERVAL: The interval of time (in TUs) between
- * root announcements are transmitted.
+ * root announcements are transmitted.
*
* @NL80211_MESHCONF_GATE_ANNOUNCEMENTS: Advertise that this mesh station has
- * access to a broader network beyond the MBSS. This is done via Root
- * Announcement frames.
+ * access to a broader network beyond the MBSS. This is done via Root
+ * Announcement frames.
*
* @NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL: The minimum interval of time (in
- * TUs) during which a mesh STA can send only one Action frame containing a
- * PERR element.
+ * TUs) during which a mesh STA can send only one Action frame containing a
+ * PERR element.
*
* @NL80211_MESHCONF_FORWARDING: set Mesh STA as forwarding or non-forwarding
- * or forwarding entity (default is TRUE - forwarding entity)
+ * or forwarding entity (default is TRUE - forwarding entity)
+ *
+ * @NL80211_MESHCONF_RSSI_THRESHOLD: RSSI threshold in dBm. This specifies the
+ * threshold for average signal strength of candidate station to establish
+ * a peer link.
+ *
+ * @NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR: maximum number of neighbors
+ * to synchronize to for 11s default synchronization method
+ * (see 11C.12.2.2)
+ *
+ * @NL80211_MESHCONF_HT_OPMODE: set mesh HT protection mode.
*
* @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute
*
+ * @NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT: The time (in TUs) for
+ * which mesh STAs receiving a proactive PREQ shall consider the forwarding
+ * information to the root mesh STA to be valid.
+ *
+ * @NL80211_MESHCONF_HWMP_ROOT_INTERVAL: The interval of time (in TUs) between
+ * proactive PREQs are transmitted.
+ *
+ * @NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL: The minimum interval of time
+ * (in TUs) during which a mesh STA can send only one Action frame
+ * containing a PREQ element for root path confirmation.
+ *
+ * @NL80211_MESHCONF_POWER_MODE: Default mesh power mode for new peer links.
+ * type &enum nl80211_mesh_power_mode (u32)
+ *
+ * @NL80211_MESHCONF_AWAKE_WINDOW: awake window duration (in TUs)
+ *
+ * @NL80211_MESHCONF_PLINK_TIMEOUT: If no tx activity is seen from a STA we've
+ * established peering with for longer than this time (in seconds), then
+ * remove it from the STA's list of peers. Default is 30 minutes.
+ *
* @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
*/
enum nl80211_meshconf_params {
NL80211_MESHCONF_GATE_ANNOUNCEMENTS,
NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL,
NL80211_MESHCONF_FORWARDING,
+ NL80211_MESHCONF_RSSI_THRESHOLD,
+ NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR,
+ NL80211_MESHCONF_HT_OPMODE,
+ NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT,
+ NL80211_MESHCONF_HWMP_ROOT_INTERVAL,
+ NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL,
+ NL80211_MESHCONF_POWER_MODE,
+ NL80211_MESHCONF_AWAKE_WINDOW,
+ NL80211_MESHCONF_PLINK_TIMEOUT,
/* keep last */
__NL80211_MESHCONF_ATTR_AFTER_LAST,
* @__NL80211_MESH_SETUP_INVALID: Internal use
*
* @NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL: Enable this option to use a
- * vendor specific path selection algorithm or disable it to use the default
- * HWMP.
+ * vendor specific path selection algorithm or disable it to use the
+ * default HWMP.
*
* @NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC: Enable this option to use a
- * vendor specific path metric or disable it to use the default Airtime
- * metric.
+ * vendor specific path metric or disable it to use the default Airtime
+ * metric.
*
* @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a
- * robust security network ie, or a vendor specific information element that
- * vendors will use to identify the path selection methods and metrics in use.
+ * robust security network ie, or a vendor specific information element
+ * that vendors will use to identify the path selection methods and
+ * metrics in use.
*
* @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication
- * daemon will be authenticating mesh candidates.
+ * daemon will be authenticating mesh candidates.
*
* @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication
- * daemon will be securing peer link frames. AMPE is a secured version of Mesh
- * Peering Management (MPM) and is implemented with the assistance of a
- * userspace daemon. When this flag is set, the kernel will send peer
- * management frames to a userspace daemon that will implement AMPE
- * functionality (security capabilities selection, key confirmation, and key
- * management). When the flag is unset (default), the kernel can autonomously
- * complete (unsecured) mesh peering without the need of a userspace daemon.
+ * daemon will be securing peer link frames. AMPE is a secured version of
+ * Mesh Peering Management (MPM) and is implemented with the assistance of
+ * a userspace daemon. When this flag is set, the kernel will send peer
+ * management frames to a userspace daemon that will implement AMPE
+ * functionality (security capabilities selection, key confirmation, and
+ * key management). When the flag is unset (default), the kernel can
+ * autonomously complete (unsecured) mesh peering without the need of a
+ * userspace daemon.
+ *
+ * @NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC: Enable this option to use a
+ * vendor specific synchronization method or disable it to use the default
+ * neighbor offset synchronization
+ *
+ * @NL80211_MESH_SETUP_USERSPACE_MPM: Enable this option if userspace will
+ * implement an MPM which handles peer allocation and state.
+ *
+ * @NL80211_MESH_SETUP_AUTH_PROTOCOL: Inform the kernel of the authentication
+ * method (u8, as defined in IEEE 8.4.2.100.6, e.g. 0x1 for SAE).
+ * Default is no authentication method required.
*
* @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
+ *
* @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use
*/
enum nl80211_mesh_setup_params {
NL80211_MESH_SETUP_IE,
NL80211_MESH_SETUP_USERSPACE_AUTH,
NL80211_MESH_SETUP_USERSPACE_AMPE,
+ NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC,
+ NL80211_MESH_SETUP_USERSPACE_MPM,
+ NL80211_MESH_SETUP_AUTH_PROTOCOL,
/* keep last */
__NL80211_MESH_SETUP_ATTR_AFTER_LAST,
/**
* enum nl80211_txq_attr - TX queue parameter attributes
* @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved
- * @NL80211_TXQ_ATTR_QUEUE: TX queue identifier (NL80211_TXQ_Q_*)
+ * @NL80211_TXQ_ATTR_AC: AC identifier (NL80211_AC_*)
* @NL80211_TXQ_ATTR_TXOP: Maximum burst time in units of 32 usecs, 0 meaning
* disabled
* @NL80211_TXQ_ATTR_CWMIN: Minimum contention window [a value of the form
*/
enum nl80211_txq_attr {
__NL80211_TXQ_ATTR_INVALID,
- NL80211_TXQ_ATTR_QUEUE,
+ NL80211_TXQ_ATTR_AC,
NL80211_TXQ_ATTR_TXOP,
NL80211_TXQ_ATTR_CWMIN,
NL80211_TXQ_ATTR_CWMAX,
NL80211_TXQ_ATTR_MAX = __NL80211_TXQ_ATTR_AFTER_LAST - 1
};
-enum nl80211_txq_q {
- NL80211_TXQ_Q_VO,
- NL80211_TXQ_Q_VI,
- NL80211_TXQ_Q_BE,
- NL80211_TXQ_Q_BK
+enum nl80211_ac {
+ NL80211_AC_VO,
+ NL80211_AC_VI,
+ NL80211_AC_BE,
+ NL80211_AC_BK,
+ NL80211_NUM_ACS
};
+/* backward compat */
+#define NL80211_TXQ_ATTR_QUEUE NL80211_TXQ_ATTR_AC
+#define NL80211_TXQ_Q_VO NL80211_AC_VO
+#define NL80211_TXQ_Q_VI NL80211_AC_VI
+#define NL80211_TXQ_Q_BE NL80211_AC_BE
+#define NL80211_TXQ_Q_BK NL80211_AC_BK
+
+/**
+ * enum nl80211_channel_type - channel type
+ * @NL80211_CHAN_NO_HT: 20 MHz, non-HT channel
+ * @NL80211_CHAN_HT20: 20 MHz HT channel
+ * @NL80211_CHAN_HT40MINUS: HT40 channel, secondary channel
+ * below the control channel
+ * @NL80211_CHAN_HT40PLUS: HT40 channel, secondary channel
+ * above the control channel
+ */
enum nl80211_channel_type {
NL80211_CHAN_NO_HT,
NL80211_CHAN_HT20,
NL80211_CHAN_HT40PLUS
};
+/**
+ * enum nl80211_chan_width - channel width definitions
+ *
+ * These values are used with the %NL80211_ATTR_CHANNEL_WIDTH
+ * attribute.
+ *
+ * @NL80211_CHAN_WIDTH_20_NOHT: 20 MHz, non-HT channel
+ * @NL80211_CHAN_WIDTH_20: 20 MHz HT channel
+ * @NL80211_CHAN_WIDTH_40: 40 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
+ * attribute must be provided as well
+ * @NL80211_CHAN_WIDTH_80: 80 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
+ * attribute must be provided as well
+ * @NL80211_CHAN_WIDTH_80P80: 80+80 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
+ * and %NL80211_ATTR_CENTER_FREQ2 attributes must be provided as well
+ * @NL80211_CHAN_WIDTH_160: 160 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
+ * attribute must be provided as well
+ * @NL80211_CHAN_WIDTH_5: 5 MHz OFDM channel
+ * @NL80211_CHAN_WIDTH_10: 10 MHz OFDM channel
+ */
+enum nl80211_chan_width {
+ NL80211_CHAN_WIDTH_20_NOHT,
+ NL80211_CHAN_WIDTH_20,
+ NL80211_CHAN_WIDTH_40,
+ NL80211_CHAN_WIDTH_80,
+ NL80211_CHAN_WIDTH_80P80,
+ NL80211_CHAN_WIDTH_160,
+ NL80211_CHAN_WIDTH_5,
+ NL80211_CHAN_WIDTH_10,
+};
+
+/**
+ * enum nl80211_bss_scan_width - control channel width for a BSS
+ *
+ * These values are used with the %NL80211_BSS_CHAN_WIDTH attribute.
+ *
+ * @NL80211_BSS_CHAN_WIDTH_20: control channel is 20 MHz wide or compatible
+ * @NL80211_BSS_CHAN_WIDTH_10: control channel is 10 MHz wide
+ * @NL80211_BSS_CHAN_WIDTH_5: control channel is 5 MHz wide
+ */
+enum nl80211_bss_scan_width {
+ NL80211_BSS_CHAN_WIDTH_20,
+ NL80211_BSS_CHAN_WIDTH_10,
+ NL80211_BSS_CHAN_WIDTH_5,
+};
+
/**
* enum nl80211_bss - netlink attributes for a BSS
*
* @NL80211_BSS_BEACON_IES: binary attribute containing the raw information
* elements from a Beacon frame (bin); not present if no Beacon frame has
* yet been received
+ * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
+ * (u32, enum nl80211_bss_scan_width)
* @__NL80211_BSS_AFTER_LAST: internal
* @NL80211_BSS_MAX: highest BSS attribute
*/
NL80211_BSS_STATUS,
NL80211_BSS_SEEN_MS_AGO,
NL80211_BSS_BEACON_IES,
+ NL80211_BSS_CHAN_WIDTH,
/* keep last */
__NL80211_BSS_AFTER_LAST,
* @NL80211_AUTHTYPE_SHARED_KEY: Shared Key authentication (WEP only)
* @NL80211_AUTHTYPE_FT: Fast BSS Transition (IEEE 802.11r)
* @NL80211_AUTHTYPE_NETWORK_EAP: Network EAP (some Cisco APs and mainly LEAP)
+ * @NL80211_AUTHTYPE_SAE: Simultaneous authentication of equals
* @__NL80211_AUTHTYPE_NUM: internal
* @NL80211_AUTHTYPE_MAX: maximum valid auth algorithm
* @NL80211_AUTHTYPE_AUTOMATIC: determine automatically (if necessary by
NL80211_AUTHTYPE_SHARED_KEY,
NL80211_AUTHTYPE_FT,
NL80211_AUTHTYPE_NETWORK_EAP,
+ NL80211_AUTHTYPE_SAE,
/* keep last */
__NL80211_AUTHTYPE_NUM,
* in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with
* 1 = 500 kbps) but without the IE length restriction (at most
* %NL80211_MAX_SUPP_RATES in a single array).
- * @NL80211_TXRATE_MCS: HT (MCS) rates allowed for TX rate selection
+ * @NL80211_TXRATE_HT: HT (MCS) rates allowed for TX rate selection
* in an array of MCS numbers.
+ * @NL80211_TXRATE_VHT: VHT rates allowed for TX rate selection,
+ * see &struct nl80211_txrate_vht
+ * @NL80211_TXRATE_GI: configure GI, see &enum nl80211_txrate_gi
* @__NL80211_TXRATE_AFTER_LAST: internal
* @NL80211_TXRATE_MAX: highest TX rate attribute
*/
enum nl80211_tx_rate_attributes {
__NL80211_TXRATE_INVALID,
NL80211_TXRATE_LEGACY,
- NL80211_TXRATE_MCS,
+ NL80211_TXRATE_HT,
+ NL80211_TXRATE_VHT,
+ NL80211_TXRATE_GI,
/* keep last */
__NL80211_TXRATE_AFTER_LAST,
NL80211_TXRATE_MAX = __NL80211_TXRATE_AFTER_LAST - 1
};
+#define NL80211_TXRATE_MCS NL80211_TXRATE_HT
+#define NL80211_VHT_NSS_MAX 8
+
+/**
+ * struct nl80211_txrate_vht - VHT MCS/NSS txrate bitmap
+ * @mcs: MCS bitmap table for each NSS (array index 0 for 1 stream, etc.)
+ */
+struct nl80211_txrate_vht {
+ __u16 mcs[NL80211_VHT_NSS_MAX];
+};
+
+enum nl80211_txrate_gi {
+ NL80211_TXRATE_DEFAULT_GI,
+ NL80211_TXRATE_FORCE_SGI,
+ NL80211_TXRATE_FORCE_LGI,
+};
+
/**
* enum nl80211_band - Frequency band
* @NL80211_BAND_2GHZ: 2.4 GHz ISM band
* @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz)
+ * @NL80211_BAND_60GHZ: around 60 GHz band (58.32 - 64.80 GHz)
*/
enum nl80211_band {
NL80211_BAND_2GHZ,
NL80211_BAND_5GHZ,
+ NL80211_BAND_60GHZ,
};
+/**
+ * enum nl80211_ps_state - powersave state
+ * @NL80211_PS_DISABLED: powersave is disabled
+ * @NL80211_PS_ENABLED: powersave is enabled
+ */
enum nl80211_ps_state {
NL80211_PS_DISABLED,
NL80211_PS_ENABLED,
* @NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT: RSSI threshold event
* @NL80211_ATTR_CQM_PKT_LOSS_EVENT: a u32 value indicating that this many
* consecutive packets were not acknowledged by the peer
+ * @NL80211_ATTR_CQM_TXE_RATE: TX error rate in %. Minimum % of TX failures
+ * during the given %NL80211_ATTR_CQM_TXE_INTVL before an
+ * %NL80211_CMD_NOTIFY_CQM with reported %NL80211_ATTR_CQM_TXE_RATE and
+ * %NL80211_ATTR_CQM_TXE_PKTS is generated.
+ * @NL80211_ATTR_CQM_TXE_PKTS: number of attempted packets in a given
+ * %NL80211_ATTR_CQM_TXE_INTVL before %NL80211_ATTR_CQM_TXE_RATE is
+ * checked.
+ * @NL80211_ATTR_CQM_TXE_INTVL: interval in seconds. Specifies the periodic
+ * interval in which %NL80211_ATTR_CQM_TXE_PKTS and
+ * %NL80211_ATTR_CQM_TXE_RATE must be satisfied before generating an
+ * %NL80211_CMD_NOTIFY_CQM. Set to 0 to turn off TX error reporting.
* @__NL80211_ATTR_CQM_AFTER_LAST: internal
* @NL80211_ATTR_CQM_MAX: highest key attribute
*/
NL80211_ATTR_CQM_RSSI_HYST,
NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT,
NL80211_ATTR_CQM_PKT_LOSS_EVENT,
+ NL80211_ATTR_CQM_TXE_RATE,
+ NL80211_ATTR_CQM_TXE_PKTS,
+ NL80211_ATTR_CQM_TXE_INTVL,
/* keep last */
__NL80211_ATTR_CQM_AFTER_LAST,
* configured threshold
* @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the
* configured threshold
+ * @NL80211_CQM_RSSI_BEACON_LOSS_EVENT: The device experienced beacon loss.
+ * (Note that deauth/disassoc will still follow if the AP is not
+ * available. This event might get used as roaming event, etc.)
*/
enum nl80211_cqm_rssi_threshold_event {
NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW,
NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
+ NL80211_CQM_RSSI_BEACON_LOSS_EVENT,
};
};
/**
- * enum nl80211_wowlan_packet_pattern_attr - WoWLAN packet pattern attribute
- * @__NL80211_WOWLAN_PKTPAT_INVALID: invalid number for nested attribute
- * @NL80211_WOWLAN_PKTPAT_PATTERN: the pattern, values where the mask has
+ * enum nl80211_packet_pattern_attr - packet pattern attribute
+ * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
+ * @NL80211_PKTPAT_PATTERN: the pattern, values where the mask has
* a zero bit are ignored
- * @NL80211_WOWLAN_PKTPAT_MASK: pattern mask, must be long enough to have
+ * @NL80211_PKTPAT_MASK: pattern mask, must be long enough to have
* a bit for each byte in the pattern. The lowest-order bit corresponds
* to the first byte of the pattern, but the bytes of the pattern are
* in a little-endian-like format, i.e. the 9th byte of the pattern
* corresponds to the lowest-order bit in the second byte of the mask.
* For example: The match 00:xx:00:00:xx:00:00:00:00:xx:xx:xx (where
* xx indicates "don't care") would be represented by a pattern of
- * twelve zero bytes, and a mask of "0xed,0x07".
+ * twelve zero bytes, and a mask of "0xed,0x01".
* Note that the pattern matching is done as though frames were not
* 802.11 frames but 802.3 frames, i.e. the frame is fully unpacked
* first (including SNAP header unpacking) and then matched.
- * @NUM_NL80211_WOWLAN_PKTPAT: number of attributes
- * @MAX_NL80211_WOWLAN_PKTPAT: max attribute number
+ * @NL80211_PKTPAT_OFFSET: packet offset, pattern is matched after
+ * these fixed number of bytes of received packet
+ * @NUM_NL80211_PKTPAT: number of attributes
+ * @MAX_NL80211_PKTPAT: max attribute number
*/
-enum nl80211_wowlan_packet_pattern_attr {
- __NL80211_WOWLAN_PKTPAT_INVALID,
- NL80211_WOWLAN_PKTPAT_MASK,
- NL80211_WOWLAN_PKTPAT_PATTERN,
-
- NUM_NL80211_WOWLAN_PKTPAT,
- MAX_NL80211_WOWLAN_PKTPAT = NUM_NL80211_WOWLAN_PKTPAT - 1,
+enum nl80211_packet_pattern_attr {
+ __NL80211_PKTPAT_INVALID,
+ NL80211_PKTPAT_MASK,
+ NL80211_PKTPAT_PATTERN,
+ NL80211_PKTPAT_OFFSET,
+
+ NUM_NL80211_PKTPAT,
+ MAX_NL80211_PKTPAT = NUM_NL80211_PKTPAT - 1,
};
/**
- * struct nl80211_wowlan_pattern_support - pattern support information
+ * struct nl80211_pattern_support - packet pattern support information
* @max_patterns: maximum number of patterns supported
* @min_pattern_len: minimum length of each pattern
* @max_pattern_len: maximum length of each pattern
+ * @max_pkt_offset: maximum Rx packet offset
*
* This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when
- * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED in the
- * capability information given by the kernel to userspace.
+ * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED or in
+ * %NL80211_ATTR_COALESCE_RULE_PKT_PATTERN when that is part of
+ * %NL80211_ATTR_COALESCE_RULE in the capability information given
+ * by the kernel to userspace.
*/
-struct nl80211_wowlan_pattern_support {
+struct nl80211_pattern_support {
__u32 max_patterns;
__u32 min_pattern_len;
__u32 max_pattern_len;
+ __u32 max_pkt_offset;
} __attribute__((packed));
+/* only for backward compatibility */
+#define __NL80211_WOWLAN_PKTPAT_INVALID __NL80211_PKTPAT_INVALID
+#define NL80211_WOWLAN_PKTPAT_MASK NL80211_PKTPAT_MASK
+#define NL80211_WOWLAN_PKTPAT_PATTERN NL80211_PKTPAT_PATTERN
+#define NL80211_WOWLAN_PKTPAT_OFFSET NL80211_PKTPAT_OFFSET
+#define NUM_NL80211_WOWLAN_PKTPAT NUM_NL80211_PKTPAT
+#define MAX_NL80211_WOWLAN_PKTPAT MAX_NL80211_PKTPAT
+#define nl80211_wowlan_pattern_support nl80211_pattern_support
+
/**
* enum nl80211_wowlan_triggers - WoWLAN trigger definitions
* @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes
* @NL80211_WOWLAN_TRIG_PKT_PATTERN: wake up on the specified packet patterns
* which are passed in an array of nested attributes, each nested attribute
* defining a with attributes from &struct nl80211_wowlan_trig_pkt_pattern.
- * Each pattern defines a wakeup packet. The matching is done on the MSDU,
- * i.e. as though the packet was an 802.3 packet, so the pattern matching
- * is done after the packet is converted to the MSDU.
+ * Each pattern defines a wakeup packet. Packet offset is associated with
+ * each pattern which is used while matching the pattern. The matching is
+ * done on the MSDU, i.e. as though the packet was an 802.3 packet, so the
+ * pattern matching is done after the packet is converted to the MSDU.
*
* In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute
- * carrying a &struct nl80211_wowlan_pattern_support.
+ * carrying a &struct nl80211_pattern_support.
+ *
+ * When reporting wakeup. it is a u32 attribute containing the 0-based
+ * index of the pattern that caused the wakeup, in the patterns passed
+ * to the kernel when configuring.
* @NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED: Not a real trigger, and cannot be
* used when setting, used only to indicate that GTK rekeying is supported
* by the device (flag)
* @NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE: wake up on 4-way handshake (flag)
* @NL80211_WOWLAN_TRIG_RFKILL_RELEASE: wake up when rfkill is released
* (on devices that have rfkill in the device) (flag)
+ * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211: For wakeup reporting only, contains
+ * the 802.11 packet that caused the wakeup, e.g. a deauth frame. The frame
+ * may be truncated, the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN
+ * attribute contains the original length.
+ * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN: Original length of the 802.11
+ * packet, may be bigger than the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211
+ * attribute if the packet was truncated somewhere.
+ * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023: For wakeup reporting only, contains the
+ * 802.11 packet that caused the wakeup, e.g. a magic packet. The frame may
+ * be truncated, the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN attribute
+ * contains the original length.
+ * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN: Original length of the 802.3
+ * packet, may be bigger than the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023
+ * attribute if the packet was truncated somewhere.
+ * @NL80211_WOWLAN_TRIG_TCP_CONNECTION: TCP connection wake, see DOC section
+ * "TCP connection wakeup" for more details. This is a nested attribute
+ * containing the exact information for establishing and keeping alive
+ * the TCP connection.
+ * @NL80211_WOWLAN_TRIG_TCP_WAKEUP_MATCH: For wakeup reporting only, the
+ * wakeup packet was received on the TCP connection
+ * @NL80211_WOWLAN_TRIG_WAKEUP_TCP_CONNLOST: For wakeup reporting only, the
+ * TCP connection was lost or failed to be established
+ * @NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS: For wakeup reporting only,
+ * the TCP connection ran out of tokens to use for data to send to the
+ * service
* @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers
* @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number
+ *
+ * These nested attributes are used to configure the wakeup triggers and
+ * to report the wakeup reason(s).
*/
enum nl80211_wowlan_triggers {
__NL80211_WOWLAN_TRIG_INVALID,
NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST,
NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE,
NL80211_WOWLAN_TRIG_RFKILL_RELEASE,
+ NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211,
+ NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN,
+ NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023,
+ NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN,
+ NL80211_WOWLAN_TRIG_TCP_CONNECTION,
+ NL80211_WOWLAN_TRIG_WAKEUP_TCP_MATCH,
+ NL80211_WOWLAN_TRIG_WAKEUP_TCP_CONNLOST,
+ NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS,
/* keep last */
NUM_NL80211_WOWLAN_TRIG,
MAX_NL80211_WOWLAN_TRIG = NUM_NL80211_WOWLAN_TRIG - 1
};
+/**
+ * DOC: TCP connection wakeup
+ *
+ * Some devices can establish a TCP connection in order to be woken up by a
+ * packet coming in from outside their network segment, or behind NAT. If
+ * configured, the device will establish a TCP connection to the given
+ * service, and periodically send data to that service. The first data
+ * packet is usually transmitted after SYN/ACK, also ACKing the SYN/ACK.
+ * The data packets can optionally include a (little endian) sequence
+ * number (in the TCP payload!) that is generated by the device, and, also
+ * optionally, a token from a list of tokens. This serves as a keep-alive
+ * with the service, and for NATed connections, etc.
+ *
+ * During this keep-alive period, the server doesn't send any data to the
+ * client. When receiving data, it is compared against the wakeup pattern
+ * (and mask) and if it matches, the host is woken up. Similarly, if the
+ * connection breaks or cannot be established to start with, the host is
+ * also woken up.
+ *
+ * Developer's note: ARP offload is required for this, otherwise TCP
+ * response packets might not go through correctly.
+ */
+
+/**
+ * struct nl80211_wowlan_tcp_data_seq - WoWLAN TCP data sequence
+ * @start: starting value
+ * @offset: offset of sequence number in packet
+ * @len: length of the sequence value to write, 1 through 4
+ *
+ * Note: don't confuse with the TCP sequence number(s), this is for the
+ * keepalive packet payload. The actual value is written into the packet
+ * in little endian.
+ */
+struct nl80211_wowlan_tcp_data_seq {
+ __u32 start, offset, len;
+};
+
+/**
+ * struct nl80211_wowlan_tcp_data_token - WoWLAN TCP data token config
+ * @offset: offset of token in packet
+ * @len: length of each token
+ * @token_stream: stream of data to be used for the tokens, the length must
+ * be a multiple of @len for this to make sense
+ */
+struct nl80211_wowlan_tcp_data_token {
+ __u32 offset, len;
+ __u8 token_stream[];
+};
+
+/**
+ * struct nl80211_wowlan_tcp_data_token_feature - data token features
+ * @min_len: minimum token length
+ * @max_len: maximum token length
+ * @bufsize: total available token buffer size (max size of @token_stream)
+ */
+struct nl80211_wowlan_tcp_data_token_feature {
+ __u32 min_len, max_len, bufsize;
+};
+
+/**
+ * enum nl80211_wowlan_tcp_attrs - WoWLAN TCP connection parameters
+ * @__NL80211_WOWLAN_TCP_INVALID: invalid number for nested attributes
+ * @NL80211_WOWLAN_TCP_SRC_IPV4: source IPv4 address (in network byte order)
+ * @NL80211_WOWLAN_TCP_DST_IPV4: destination IPv4 address
+ * (in network byte order)
+ * @NL80211_WOWLAN_TCP_DST_MAC: destination MAC address, this is given because
+ * route lookup when configured might be invalid by the time we suspend,
+ * and doing a route lookup when suspending is no longer possible as it
+ * might require ARP querying.
+ * @NL80211_WOWLAN_TCP_SRC_PORT: source port (u16); optional, if not given a
+ * socket and port will be allocated
+ * @NL80211_WOWLAN_TCP_DST_PORT: destination port (u16)
+ * @NL80211_WOWLAN_TCP_DATA_PAYLOAD: data packet payload, at least one byte.
+ * For feature advertising, a u32 attribute holding the maximum length
+ * of the data payload.
+ * @NL80211_WOWLAN_TCP_DATA_PAYLOAD_SEQ: data packet sequence configuration
+ * (if desired), a &struct nl80211_wowlan_tcp_data_seq. For feature
+ * advertising it is just a flag
+ * @NL80211_WOWLAN_TCP_DATA_PAYLOAD_TOKEN: data packet token configuration,
+ * see &struct nl80211_wowlan_tcp_data_token and for advertising see
+ * &struct nl80211_wowlan_tcp_data_token_feature.
+ * @NL80211_WOWLAN_TCP_DATA_INTERVAL: data interval in seconds, maximum
+ * interval in feature advertising (u32)
+ * @NL80211_WOWLAN_TCP_WAKE_PAYLOAD: wake packet payload, for advertising a
+ * u32 attribute holding the maximum length
+ * @NL80211_WOWLAN_TCP_WAKE_MASK: Wake packet payload mask, not used for
+ * feature advertising. The mask works like @NL80211_PKTPAT_MASK
+ * but on the TCP payload only.
+ * @NUM_NL80211_WOWLAN_TCP: number of TCP attributes
+ * @MAX_NL80211_WOWLAN_TCP: highest attribute number
+ */
+enum nl80211_wowlan_tcp_attrs {
+ __NL80211_WOWLAN_TCP_INVALID,
+ NL80211_WOWLAN_TCP_SRC_IPV4,
+ NL80211_WOWLAN_TCP_DST_IPV4,
+ NL80211_WOWLAN_TCP_DST_MAC,
+ NL80211_WOWLAN_TCP_SRC_PORT,
+ NL80211_WOWLAN_TCP_DST_PORT,
+ NL80211_WOWLAN_TCP_DATA_PAYLOAD,
+ NL80211_WOWLAN_TCP_DATA_PAYLOAD_SEQ,
+ NL80211_WOWLAN_TCP_DATA_PAYLOAD_TOKEN,
+ NL80211_WOWLAN_TCP_DATA_INTERVAL,
+ NL80211_WOWLAN_TCP_WAKE_PAYLOAD,
+ NL80211_WOWLAN_TCP_WAKE_MASK,
+
+ /* keep last */
+ NUM_NL80211_WOWLAN_TCP,
+ MAX_NL80211_WOWLAN_TCP = NUM_NL80211_WOWLAN_TCP - 1
+};
+
+/**
+ * struct nl80211_coalesce_rule_support - coalesce rule support information
+ * @max_rules: maximum number of rules supported
+ * @pat: packet pattern support information
+ * @max_delay: maximum supported coalescing delay in msecs
+ *
+ * This struct is carried in %NL80211_ATTR_COALESCE_RULE in the
+ * capability information given by the kernel to userspace.
+ */
+struct nl80211_coalesce_rule_support {
+ __u32 max_rules;
+ struct nl80211_pattern_support pat;
+ __u32 max_delay;
+} __attribute__((packed));
+
+/**
+ * enum nl80211_attr_coalesce_rule - coalesce rule attribute
+ * @__NL80211_COALESCE_RULE_INVALID: invalid number for nested attribute
+ * @NL80211_ATTR_COALESCE_RULE_DELAY: delay in msecs used for packet coalescing
+ * @NL80211_ATTR_COALESCE_RULE_CONDITION: condition for packet coalescence,
+ * see &enum nl80211_coalesce_condition.
+ * @NL80211_ATTR_COALESCE_RULE_PKT_PATTERN: packet offset, pattern is matched
+ * after these fixed number of bytes of received packet
+ * @NUM_NL80211_ATTR_COALESCE_RULE: number of attributes
+ * @NL80211_ATTR_COALESCE_RULE_MAX: max attribute number
+ */
+enum nl80211_attr_coalesce_rule {
+ __NL80211_COALESCE_RULE_INVALID,
+ NL80211_ATTR_COALESCE_RULE_DELAY,
+ NL80211_ATTR_COALESCE_RULE_CONDITION,
+ NL80211_ATTR_COALESCE_RULE_PKT_PATTERN,
+
+ /* keep last */
+ NUM_NL80211_ATTR_COALESCE_RULE,
+ NL80211_ATTR_COALESCE_RULE_MAX = NUM_NL80211_ATTR_COALESCE_RULE - 1
+};
+
+/**
+ * enum nl80211_coalesce_condition - coalesce rule conditions
+ * @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns
+ * in a rule are matched.
+ * @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns
+ * in a rule are not matched.
+ */
+enum nl80211_coalesce_condition {
+ NL80211_COALESCE_CONDITION_MATCH,
+ NL80211_COALESCE_CONDITION_NO_MATCH
+};
+
/**
* enum nl80211_iface_limit_attrs - limit attributes
* @NL80211_IFACE_LIMIT_UNSPEC: (reserved)
* the infrastructure network's beacon interval.
* @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many
* different channels may be used within this group.
+ * @NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS: u32 attribute containing the bitmap
+ * of supported channel widths for radar detection.
+ * @NL80211_IFACE_COMB_RADAR_DETECT_REGIONS: u32 attribute containing the bitmap
+ * of supported regulatory regions for radar detection.
* @NUM_NL80211_IFACE_COMB: number of attributes
* @MAX_NL80211_IFACE_COMB: highest attribute number
*
NL80211_IFACE_COMB_MAXNUM,
NL80211_IFACE_COMB_STA_AP_BI_MATCH,
NL80211_IFACE_COMB_NUM_CHANNELS,
+ NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS,
+ NL80211_IFACE_COMB_RADAR_DETECT_REGIONS,
/* keep last */
NUM_NL80211_IFACE_COMB,
MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1
};
+/**
+ * enum nl80211_plink_action - actions to perform in mesh peers
+ *
+ * @NL80211_PLINK_ACTION_NO_ACTION: perform no action
+ * @NL80211_PLINK_ACTION_OPEN: start mesh peer link establishment
+ * @NL80211_PLINK_ACTION_BLOCK: block traffic from this mesh peer
+ * @NUM_NL80211_PLINK_ACTIONS: number of possible actions
+ */
+enum plink_actions {
+ NL80211_PLINK_ACTION_NO_ACTION,
+ NL80211_PLINK_ACTION_OPEN,
+ NL80211_PLINK_ACTION_BLOCK,
+
+ NUM_NL80211_PLINK_ACTIONS,
+};
+
+
#define NL80211_KCK_LEN 16
#define NL80211_KEK_LEN 16
#define NL80211_REPLAY_CTR_LEN 8
* TX status to the socket error queue when requested with the
* socket option.
* @NL80211_FEATURE_HT_IBSS: This driver supports IBSS with HT datarates.
+ * @NL80211_FEATURE_INACTIVITY_TIMER: This driver takes care of freeing up
+ * the connected inactive stations in AP mode.
+ * @NL80211_FEATURE_CELL_BASE_REG_HINTS: This driver has been tested
+ * to work properly to suppport receiving regulatory hints from
+ * cellular base stations.
+ * @NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL: (no longer available, only
+ * here to reserve the value for API/ABI compatibility)
+ * @NL80211_FEATURE_SAE: This driver supports simultaneous authentication of
+ * equals (SAE) with user space SME (NL80211_CMD_AUTHENTICATE) in station
+ * mode
+ * @NL80211_FEATURE_LOW_PRIORITY_SCAN: This driver supports low priority scan
+ * @NL80211_FEATURE_SCAN_FLUSH: Scan flush is supported
+ * @NL80211_FEATURE_AP_SCAN: Support scanning using an AP vif
+ * @NL80211_FEATURE_VIF_TXPOWER: The driver supports per-vif TX power setting
+ * @NL80211_FEATURE_NEED_OBSS_SCAN: The driver expects userspace to perform
+ * OBSS scans and generate 20/40 BSS coex reports. This flag is used only
+ * for drivers implementing the CONNECT API, for AUTH/ASSOC it is implied.
+ * @NL80211_FEATURE_P2P_GO_CTWIN: P2P GO implementation supports CT Window
+ * setting
+ * @NL80211_FEATURE_P2P_GO_OPPPS: P2P GO implementation supports opportunistic
+ * powersave
+ * @NL80211_FEATURE_FULL_AP_CLIENT_STATE: The driver supports full state
+ * transitions for AP clients. Without this flag (and if the driver
+ * doesn't have the AP SME in the device) the driver supports adding
+ * stations only when they're associated and adds them in associated
+ * state (to later be transitioned into authorized), with this flag
+ * they should be added before even sending the authentication reply
+ * and then transitioned into authenticated, associated and authorized
+ * states using station flags.
+ * Note that even for drivers that support this, the default is to add
+ * stations in authenticated/associated state, so to add unauthenticated
+ * stations the authenticated/associated bits have to be set in the mask.
+ * @NL80211_FEATURE_ADVERTISE_CHAN_LIMITS: cfg80211 advertises channel limits
+ * (HT40, VHT 80/160 MHz) if this flag is set
+ * @NL80211_FEATURE_USERSPACE_MPM: This driver supports a userspace Mesh
+ * Peering Management entity which may be implemented by registering for
+ * beacons or NL80211_CMD_NEW_PEER_CANDIDATE events. The mesh beacon is
+ * still generated by the driver.
+ * @NL80211_FEATURE_ACTIVE_MONITOR: This driver supports an active monitor
+ * interface. An active monitor interface behaves like a normal monitor
+ * interface, but gets added to the driver. It ensures that incoming
+ * unicast packets directed at the configured interface address get ACKed.
+ * @NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE: This driver supports dynamic
+ * channel bandwidth change (e.g., HT 20 <-> 40 MHz channel) during the
+ * lifetime of a BSS.
*/
enum nl80211_feature_flags {
- NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
- NL80211_FEATURE_HT_IBSS = 1 << 1,
+ NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
+ NL80211_FEATURE_HT_IBSS = 1 << 1,
+ NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2,
+ NL80211_FEATURE_CELL_BASE_REG_HINTS = 1 << 3,
+ NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL = 1 << 4,
+ NL80211_FEATURE_SAE = 1 << 5,
+ NL80211_FEATURE_LOW_PRIORITY_SCAN = 1 << 6,
+ NL80211_FEATURE_SCAN_FLUSH = 1 << 7,
+ NL80211_FEATURE_AP_SCAN = 1 << 8,
+ NL80211_FEATURE_VIF_TXPOWER = 1 << 9,
+ NL80211_FEATURE_NEED_OBSS_SCAN = 1 << 10,
+ NL80211_FEATURE_P2P_GO_CTWIN = 1 << 11,
+ NL80211_FEATURE_P2P_GO_OPPPS = 1 << 12,
+ /* bit 13 is reserved */
+ NL80211_FEATURE_ADVERTISE_CHAN_LIMITS = 1 << 14,
+ NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 15,
+ NL80211_FEATURE_USERSPACE_MPM = 1 << 16,
+ NL80211_FEATURE_ACTIVE_MONITOR = 1 << 17,
+ NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE = 1 << 18,
};
/**
NL80211_PROBE_RESP_OFFLOAD_SUPPORT_80211U = 1<<3,
};
+/**
+ * enum nl80211_connect_failed_reason - connection request failed reasons
+ * @NL80211_CONN_FAIL_MAX_CLIENTS: Maximum number of clients that can be
+ * handled by the AP is reached.
+ * @NL80211_CONN_FAIL_BLOCKED_CLIENT: Connection request is rejected due to ACL.
+ */
+enum nl80211_connect_failed_reason {
+ NL80211_CONN_FAIL_MAX_CLIENTS,
+ NL80211_CONN_FAIL_BLOCKED_CLIENT,
+};
+
+/**
+ * enum nl80211_scan_flags - scan request control flags
+ *
+ * Scan request control flags are used to control the handling
+ * of NL80211_CMD_TRIGGER_SCAN and NL80211_CMD_START_SCHED_SCAN
+ * requests.
+ *
+ * @NL80211_SCAN_FLAG_LOW_PRIORITY: scan request has low priority
+ * @NL80211_SCAN_FLAG_FLUSH: flush cache before scanning
+ * @NL80211_SCAN_FLAG_AP: force a scan even if the interface is configured
+ * as AP and the beaconing has already been configured. This attribute is
+ * dangerous because will destroy stations performance as a lot of frames
+ * will be lost while scanning off-channel, therefore it must be used only
+ * when really needed
+ */
+enum nl80211_scan_flags {
+ NL80211_SCAN_FLAG_LOW_PRIORITY = 1<<0,
+ NL80211_SCAN_FLAG_FLUSH = 1<<1,
+ NL80211_SCAN_FLAG_AP = 1<<2,
+};
+
+/**
+ * enum nl80211_acl_policy - access control policy
+ *
+ * Access control policy is applied on a MAC list set by
+ * %NL80211_CMD_START_AP and %NL80211_CMD_SET_MAC_ACL, to
+ * be used with %NL80211_ATTR_ACL_POLICY.
+ *
+ * @NL80211_ACL_POLICY_ACCEPT_UNLESS_LISTED: Deny stations which are
+ * listed in ACL, i.e. allow all the stations which are not listed
+ * in ACL to authenticate.
+ * @NL80211_ACL_POLICY_DENY_UNLESS_LISTED: Allow the stations which are listed
+ * in ACL, i.e. deny all the stations which are not listed in ACL.
+ */
+enum nl80211_acl_policy {
+ NL80211_ACL_POLICY_ACCEPT_UNLESS_LISTED,
+ NL80211_ACL_POLICY_DENY_UNLESS_LISTED,
+};
+
+/**
+ * enum nl80211_radar_event - type of radar event for DFS operation
+ *
+ * Type of event to be used with NL80211_ATTR_RADAR_EVENT to inform userspace
+ * about detected radars or success of the channel available check (CAC)
+ *
+ * @NL80211_RADAR_DETECTED: A radar pattern has been detected. The channel is
+ * now unusable.
+ * @NL80211_RADAR_CAC_FINISHED: Channel Availability Check has been finished,
+ * the channel is now available.
+ * @NL80211_RADAR_CAC_ABORTED: Channel Availability Check has been aborted, no
+ * change to the channel status.
+ * @NL80211_RADAR_NOP_FINISHED: The Non-Occupancy Period for this channel is
+ * over, channel becomes usable.
+ */
+enum nl80211_radar_event {
+ NL80211_RADAR_DETECTED,
+ NL80211_RADAR_CAC_FINISHED,
+ NL80211_RADAR_CAC_ABORTED,
+ NL80211_RADAR_NOP_FINISHED,
+};
+
+/**
+ * enum nl80211_dfs_state - DFS states for channels
+ *
+ * Channel states used by the DFS code.
+ *
+ * @NL80211_DFS_USABLE: The channel can be used, but channel availability
+ * check (CAC) must be performed before using it for AP or IBSS.
+ * @NL80211_DFS_UNAVAILABLE: A radar has been detected on this channel, it
+ * is therefore marked as not available.
+ * @NL80211_DFS_AVAILABLE: The channel has been CAC checked and is available.
+ */
+enum nl80211_dfs_state {
+ NL80211_DFS_USABLE,
+ NL80211_DFS_UNAVAILABLE,
+ NL80211_DFS_AVAILABLE,
+};
+
+/**
+ * enum enum nl80211_protocol_features - nl80211 protocol features
+ * @NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP: nl80211 supports splitting
+ * wiphy dumps (if requested by the application with the attribute
+ * %NL80211_ATTR_SPLIT_WIPHY_DUMP. Also supported is filtering the
+ * wiphy dump by %NL80211_ATTR_WIPHY, %NL80211_ATTR_IFINDEX or
+ * %NL80211_ATTR_WDEV.
+ */
+enum nl80211_protocol_features {
+ NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP = 1 << 0,
+};
+
+/**
+ * enum nl80211_crit_proto_id - nl80211 critical protocol identifiers
+ *
+ * @NL80211_CRIT_PROTO_UNSPEC: protocol unspecified.
+ * @NL80211_CRIT_PROTO_DHCP: BOOTP or DHCPv6 protocol.
+ * @NL80211_CRIT_PROTO_EAPOL: EAPOL protocol.
+ * @NL80211_CRIT_PROTO_APIPA: APIPA protocol.
+ * @NUM_NL80211_CRIT_PROTO: must be kept last.
+ */
+enum nl80211_crit_proto_id {
+ NL80211_CRIT_PROTO_UNSPEC,
+ NL80211_CRIT_PROTO_DHCP,
+ NL80211_CRIT_PROTO_EAPOL,
+ NL80211_CRIT_PROTO_APIPA,
+ /* add other protocols before this one */
+ NUM_NL80211_CRIT_PROTO
+};
+
+/* maximum duration for critical protocol measures */
+#define NL80211_CRIT_PROTO_MAX_DURATION 5000 /* msec */
+
+/**
+ * enum nl80211_rxmgmt_flags - flags for received management frame.
+ *
+ * Used by cfg80211_rx_mgmt()
+ *
+ * @NL80211_RXMGMT_FLAG_ANSWERED: frame was answered by device/driver.
+ */
+enum nl80211_rxmgmt_flags {
+ NL80211_RXMGMT_FLAG_ANSWERED = 1 << 0,
+};
+
+/*
+ * If this flag is unset, the lower 24 bits are an OUI, if set
+ * a Linux nl80211 vendor ID is used (no such IDs are allocated
+ * yet, so that's not valid so far)
+ */
+#define NL80211_VENDOR_ID_IS_LINUX 0x80000000
+
+/**
+ * struct nl80211_vendor_cmd_info - vendor command data
+ * @vendor_id: If the %NL80211_VENDOR_ID_IS_LINUX flag is clear, then the
+ * value is a 24-bit OUI; if it is set then a separately allocated ID
+ * may be used, but no such IDs are allocated yet. New IDs should be
+ * added to this file when needed.
+ * @subcmd: sub-command ID for the command
+ */
+struct nl80211_vendor_cmd_info {
+ __u32 vendor_id;
+ __u32 subcmd;
+};
+
+/**
+ * enum nl80211_tdls_peer_capability - TDLS peer flags.
+ *
+ * Used by tdls_mgmt() to determine which conditional elements need
+ * to be added to TDLS Setup frames.
+ *
+ * @NL80211_TDLS_PEER_HT: TDLS peer is HT capable.
+ * @NL80211_TDLS_PEER_VHT: TDLS peer is VHT capable.
+ * @NL80211_TDLS_PEER_WMM: TDLS peer is WMM capable.
+ */
+enum nl80211_tdls_peer_capability {
+ NL80211_TDLS_PEER_HT = 1<<0,
+ NL80211_TDLS_PEER_VHT = 1<<1,
+ NL80211_TDLS_PEER_WMM = 1<<2,
+};
+
#endif /* __LINUX_NL80211_H */
projects / openwrt / staging / thess.git / commitdiff