--- /dev/null
+#!/bin/sh
+# Copyright (C) 2018 OpenWrt.org
+#
+
+. /lib/functions.sh
+
+# The mtd partition 'ubi' and 'rootfs_1' on NAND flash are os-image
+# partitions. These partitions are called as "Bank1/Bank2" in U-Boot
+# on WXR-2533DHP, and they are checked conditions when booting.
+# Then, U-Boot checks kernel and rootfs volumes in ubi, but U-Boot
+# needs "ubi_rootfs" as rootfs volume name. And, U-Boot checks the
+# checksum at the end of rootfs (ubi_rootfs).
+# When U-Boot writes os-image into the Bank, only kernel, rootfs
+# (ubi_rootfs) and rootfs_data (ubi_rootfs_data) volumes are wrote
+# into the Bank. (not full ubi image)
+#
+# == U-Boot Behaviors ==
+# - Bank1/Bank2 images are good, images are different
+# -> writes os-image to Bank1 from Bank2
+# (this behavior is used to firmware upgrade in stock firmware)
+# - Bank1 image is broken (or checksum error)
+# -> writes os-image to Bank1 from Bank2
+# - Bank2 image is broken (or checksum error)
+# -> writes os-image to Bank2 from Bank1
+# - Bank1/Bank2 images are broken (or checksum error)
+# -> start tftp
+
+buffalo_upgrade_prepare_ubi() {
+ local ubidev="$( nand_find_ubi ubi )"
+ local mtdnum2="$( find_mtd_index rootfs_1 )"
+
+ if [ ! "$mtdnum2" ]; then
+ echo "cannot find second ubi mtd partition rootfs_1"
+ return 1
+ fi
+
+ local ubidev2="$( nand_find_ubi rootfs_1 )"
+ if [ ! "$ubidev2" ] && [ -n "$mtdnum2" ]; then
+ ubiattach -m "$mtdnum2"
+ ubidev2="$( nand_find_ubi rootfs_1 )"
+ fi
+
+ ubirmvol /dev/$ubidev -N ubi_rootfs_data &> /dev/null || true
+ ubirmvol /dev/$ubidev2 -N kernel &> /dev/null || true
+}
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+#include "qcom-ipq8064-v2.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Buffalo WXR-2533DHP";
+ compatible = "buffalo,wxr-2533dhp", "qcom,ipq8064";
+
+ memory@42000000 {
+ reg = <0x42000000 0x1e000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &gsbi4_serial;
+
+ led-boot = &power;
+ led-failsafe = &diag;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ chosen {
+ /* use "ubi_rootfs" volume in "ubi" partition as rootfs */
+ bootargs = "ubi.block=0,1 root=/dev/ubiblock0_1 rootfstype=squashfs";
+ stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ nand@1ac00000 {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ cs@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ ubi@0 {
+ label = "ubi";
+ reg = <0x0000000 0x4000000>;
+ };
+
+ rootfs_1@4000000 {
+ label = "rootfs_1";
+ reg = <0x4000000 0x4000000>;
+ };
+ };
+ };
+ };
+
+ mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
+ <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ ethernet-phy@0 {
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x07600000 /* PAD0_MODE */
+ 0x00008 0x01000000 /* PAD5_MODE */
+ 0x0000c 0x00000080 /* PAD6_MODE */
+ 0x00050 0xcc35cc35 /* LED_CTRL0 */
+ 0x00054 0xca35ca35 /* LED_CTRL1 */
+ 0x00058 0xc935c935 /* LED_CTRL2 */
+ 0x0005c 0x03ffff00 /* LED_CTRL3 */
+ 0x000e4 0x0006a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x0000007e /* PORT0_STATUS */
+ 0x00094 0x0000007e /* PORT6_STATUS */
+ >;
+ };
+
+ ethernet-phy@4 {
+ reg = <4>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ usb {
+ label = "wxr-2533dhp:green:usb";
+ gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "usbport";
+ trigger-sources = <&hub_port0 &hub_port1>;
+ };
+
+ guestport {
+ label = "wxr-2533dhp:green:guestport";
+ gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ diag: diag {
+ label = "wxr-2533dhp:orange:diag";
+ gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ internet_orange {
+ label = "wxr-2533dhp:orange:internet";
+ gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ internet_white {
+ label = "wxr-2533dhp:white:internet";
+ gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+ };
+
+ wireless_orange {
+ label = "wxr-2533dhp:orange:wireless";
+ gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ wireless_white {
+ label = "wxr-2533dhp:white:wireless";
+ gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ router_orange {
+ label = "wxr-2533dhp:orange:router";
+ gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
+ };
+
+ router_white {
+ label = "wxr-2533dhp:white:router";
+ gpios = <&qcom_pinmux 26 GPIO_ACTIVE_LOW>;
+ };
+
+ power: power {
+ label = "wxr-2533dhp:white:power";
+ gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
+
+ power {
+ label = "power";
+ gpios = <&qcom_pinmux 58 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ eject {
+ label = "eject";
+ gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_EJECTCD>;
+ };
+
+ guest {
+ label = "guest";
+ gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_0>;
+ };
+
+ ap {
+ label = "ap";
+ gpios = <&qcom_pinmux 55 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ linux,input-type = <EV_SW>;
+ };
+
+ router {
+ label = "router";
+ gpios = <&qcom_pinmux 56 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ linux,input-type = <EV_SW>;
+ };
+
+ auto {
+ label = "auto";
+ gpios = <&qcom_pinmux 57 GPIO_ACTIVE_LOW>;
+ linux,code = <BTN_1>;
+ linux,input-type = <EV_SW>;
+ };
+ };
+};
+
+&adm_dma {
+ status = "okay";
+};
+
+&gmac1 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&ART 6>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "ok";
+
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&ART 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gsbi4 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+};
+
+&gsbi4_serial {
+ status = "okay";
+
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+};
+
+&gsbi5 {
+ status = "okay";
+ qcom,mode = <GSBI_PROT_SPI>;
+
+ spi@1a280000 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x0 0x10000>;
+ read-only;
+ };
+
+ MIBIB@10000 {
+ label = "MIBIB";
+ reg = <0x10000 0x20000>;
+ read-only;
+ };
+
+ SBL2@30000 {
+ label = "SBL2";
+ reg = <0x30000 0x30000>;
+ read-only;
+ };
+
+ SBL3@60000 {
+ label = "SBL3";
+ reg = <0x60000 0x30000>;
+ read-only;
+ };
+
+ DDRCONFIG@90000 {
+ label = "DDRCONFIG";
+ reg = <0x90000 0x10000>;
+ read-only;
+ };
+
+ SSD@a0000 {
+ label = "SSD";
+ reg = <0xa0000 0x10000>;
+ read-only;
+ };
+
+ TZ@b0000 {
+ label = "TZ";
+ reg = <0xb0000 0x30000>;
+ read-only;
+ };
+
+ RPM@e0000 {
+ label = "RPM";
+ reg = <0xe0000 0x20000>;
+ read-only;
+ };
+
+ APPSBL@100000 {
+ label = "APPSBL";
+ reg = <0x100000 0x70000>;
+ read-only;
+ };
+
+ APPSBLENV@170000 {
+ label = "APPSBLENV";
+ reg = <0x170000 0x10000>;
+ read-only;
+ };
+
+ ART: ART@180000 {
+ label = "ART";
+ reg = <0x180000 0x40000>;
+ read-only;
+ };
+
+ BOOTCONFIG@1c0000 {
+ label = "BOOTCONFIG";
+ reg = <0x1c0000 0x10000>;
+ read-only;
+ };
+
+ APPSBL_1@1d0000 {
+ label = "APPSBL_1";
+ reg = <0x1d0000 0x70000>;
+ read-only;
+ };
+ };
+ };
+ };
+};
+
+&hs_phy_0 { /* USB3 port 0 HS phy */
+ status = "okay";
+};
+
+&ss_phy_0 { /* USB3 port 0 SS phy */
+ status = "okay";
+};
+
+&hs_phy_1 { /* USB3 port 1 HS phy */
+ status = "okay";
+};
+
+&ss_phy_1 { /* USB3 port 1 SS phy */
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
+
+ pinctrl-0 = <&usb_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&usb3_1 {
+ status = "okay";
+};
+
+&dwc3_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub_port0: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&dwc3_1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hub_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+};
+
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio6", "gpio54", "gpio55", "gpio56", "gpio57",
+ "gpio58", "gpio64", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio22",
+ "gpio23", "gpio24", "gpio25", "gpio26", "gpio53";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ uart0_pins: uart0_pins {
+ mux {
+ pins = "gpio10", "gpio11";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ bias-pull-down;
+ };
+
+ data {
+ pins = "gpio18", "gpio19";
+ drive-strength = <10>;
+ };
+
+ cs{
+ pins = "gpio20";
+ drive-strength = <10>;
+ bias-pull-up;
+ };
+
+ clk {
+ pins = "gpio21";
+ drive-strength = <12>;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ mux {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39",
+ "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ pullups {
+ pins = "gpio39";
+ bias-pull-up;
+ };
+
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ bias-bus-hold;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ usb_pwr_en_pins: usb_pwr_en_pins {
+ mux{
+ pins = "gpio68";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ output-high;
+ };
+ };
+};
\ No newline at end of file
projects / openwrt / staging / zorun.git / commitdiff