kirkwood: add support for Iomega Storcenter ix4-200d

Iomega Storcenter ix4-200d is a four-bay SATA NAS powered by a Marvell
Kirkwood SoC clocked at 1.2GHz. It has 512MB of RAM and 32MB of
flash memory, 3x USB 2.0 and 2x 1Gbit/s NIC

Specification:
- SoC: Marvell Kirkwood 88F6281
- CPU/Speed: 1200Mhz
- Flash size: 32 MiB
- RAM: 512MB
- LAN: 2x 1Gbit/s
- 3x USB 2.0

Notes:
- The blue drive LED is triggered by HDD activity, it can not be controlled
  via GPIO.
- The LCD screen requires proprietary code and does not function at this time.
- Due to a kernel-related issue with the Marvell 88SE6121 SATA controller,
  currently only trays numbered #3 and #4 work, #1 and #2 do not. [1]

Serial pinout:

    CN4
    --------------
    | 10 8 6 4 2 |
    |  9 7 5 3 1 |
    -------------- PIN 1 Mark (fat line)

     1 = RXD
     4 = TXD
     6 = GND
     9 = 3.3V (not necessary to connect)

Installation instructions:
1. download initramfs-uImage and copy into tftp server
2. connect the tftp server to network port #1
3. access uboot environment with serial cable and run

    setenv mainlineLinux yes
    setenv arcNumber 1682
    setenv console 'console=ttyS0,115200n8'
    setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)'
    setenv bootargs_root 'root='
    setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000'
    saveenv
    setenv serverip 192.168.1.1
    setenv ipaddr 192.168.1.2
    tftpboot 0x00800000 [initramfs-uImage filename]
    bootm 0x00800000

4. connect to LAN on network port #2, log into openwrt and sysupgrade to install into flash

[1] https://bugzilla.kernel.org/show_bug.cgi?id=216094

Signed-off-by: Sander van Deijck <sander@vandeijck.com>
(aligned FROM from signed-off. LED+key rename, whitespace removal)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

diff --git a/target/linux/kirkwood/base-files/etc/board.d/02_network b/target/linux/kirkwood/base-files/etc/board.d/02_network
index df38694f40ca00da931df3b2481888362238b251..15f75df6a8108ab1789b124984dc53bb3167ea55 100644 (file)
--- a/target/linux/kirkwood/base-files/etc/board.d/02_network
+++ b/target/linux/kirkwood/base-files/etc/board.d/02_network
@@ -37,6 +37,9 @@ kirkwood_setup_interfaces()
        endian,4i-edge-200)
                ucidef_set_interface_lan "port1 port2 port3 port4 eth1"
                ;;
+       iom,ix4-200d)
+               ucidef_set_interface_lan "eth0 eth1" "dhcp"
+               ;;
        linksys,e4200-v2|\
        linksys,ea3500|\
        linksys,ea4500)

diff --git a/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-ix4-200d.dts b/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-ix4-200d.dts
new file mode 100644 (file)
index 0000000..c63742a
--- /dev/null
+++ b/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-ix4-200d.dts
@@ -0,0 +1,202 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+       model = "Iomega ix4-200d";
+       compatible = "iom,ix4-200d", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+       aliases {
+               led-boot = &led_status_white;
+               led-failsafe = &led_status_red;
+               led-running = &led_power_white;
+               led-upgrade = &led_status_red;
+       };
+
+       chosen {
+               bootargs = "console=ttyS0,115200n8 earlyprintk";
+               stdout-path = &uart0;
+       };
+
+       memory {
+               device_type = "memory";
+               reg = <0x00000000 0x20000000>;
+       };
+
+       ocp@f1000000 {
+               i2c@11000 {
+                       status = "okay";
+
+                       adt7473@2e {
+                               compatible = "adi,adt7473";
+                               reg = <0x2e>;
+                       };
+               };
+
+               pinctrl: pin-controller@10000 {
+                       pmx_spi: pmx-spi {
+                               marvell,pins = "mpp12", "mpp13", "mpp14";
+                               marvell,function = "gpio";
+                       };
+
+                       pmx_keys: pmx-keys {
+                               marvell,pins = "mpp16", "mpp29", "mpp47", "mpp49";
+                               marvell,function = "gpio";
+                       };
+               };
+
+               sata@80000 {
+                       status = "okay";
+                       nr-ports = <2>;
+               };
+
+               serial@12000 {
+                       status = "okay";
+               };
+
+               spi3 {
+                       compatible = "spi-gpio";
+                       #address-cells = <0x1>;
+                       ranges;
+                       status = "okay";
+                       sck-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+                       mosi-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+                       cs-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+                       num-chipselects = <1>;
+                       #size-cells = <0>;
+
+                       gpio_spi: gpio_spi@0 {
+                               compatible = "fairchild,74hc595";
+                               reg = <0>;
+                               gpio-controller;
+                               #gpio-cells = <2>;
+                               registers-number = <1>;
+                               spi-max-frequency = <100000>;
+                       };
+               };
+
+               gpio-keys {
+                       compatible = "gpio-keys";
+                       pinctrl-0 = <&pmx_keys>;
+                       pinctrl-names = "default";
+
+                       button-0 {
+                               label = "Next Button";
+                               linux,code = <BTN_0>;
+                               gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+                       };
+
+                       button-1 {
+                               label = "Reset Button";
+                               linux,code = <KEY_RESTART>;
+                               gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+                       };
+
+                       button-2 {
+                               label = "Cancel Button";
+                               linux,code = <BTN_1>;
+                               gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+                       };
+
+                       button-3 {
+                               label = "Power Button";
+                               linux,code = <KEY_POWER2>;
+                               gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+                       };
+               };
+
+               gpio-leds {
+                       compatible = "gpio-leds";
+
+                       led_status_white: led-0 {
+                               label = "status:white";
+                               function = LED_FUNCTION_STATUS;
+                               color = <LED_COLOR_ID_WHITE>;
+                               gpios = <&gpio_spi 4 GPIO_ACTIVE_LOW>;
+                       };
+
+                       led_status_red: led-1 {
+                               label = "status:red";
+                               function = LED_FUNCTION_STATUS;
+                               color = <LED_COLOR_ID_RED>;
+                               gpios = <&gpio_spi 5 GPIO_ACTIVE_LOW>;
+                       };
+
+                       led_power_white: led-2 {
+                               label = "power:white";
+                               function = LED_FUNCTION_POWER;
+                               color = <LED_COLOR_ID_WHITE>;
+                               gpios = <&gpio_spi 7 GPIO_ACTIVE_HIGH>;
+                       };
+               };
+       };
+};
+
+&eth0 {
+       status = "okay";
+       ethernet0-port@0 {
+               phy-handle = <&ethphy0>;
+       };
+};
+
+&eth1 {
+       status = "okay";
+       ethernet1-port@0 {
+               phy-handle = <&ethphy1>;
+       };
+};
+
+&mdio {
+       status = "okay";
+
+       ethphy0: ethernet-phy@8 {
+               reg = <8>;
+       };
+
+       ethphy1: ethernet-phy@9 {
+               reg = <9>;
+       };
+};
+
+&nand {
+       status = "okay";
+
+       partitions {
+               compatible = "fixed-partitions";
+               #address-cells = <1>;
+               #size-cells = <1>;
+
+               partition@0 {
+                       label = "u-boot";
+                       reg = <0x0000000 0x100000>;
+                       read-only;
+               };
+
+               partition@a0000 {
+                       label = "u-boot environment";
+                       reg = <0xa0000 0x20000>;
+                       read-only;
+               };
+
+               partition@100000 {
+                       label = "kernel";
+                       reg = <0x100000 0x300000>;
+               };
+
+               partition@400000 {
+                       label = "ubi";
+                       reg = <0x400000 0x1C00000>;
+               };
+       };
+};
+
+&pciec {
+       status = "okay";
+};
+
+&pcie0 {
+       status = "okay";
+};

diff --git a/target/linux/kirkwood/image/Makefile b/target/linux/kirkwood/image/Makefile
index ea76e21970625eceac4f45524794ed1a19410829..0fa14b89f32cf167610cb26b4dc2387ea3f702b7 100644 (file)
--- a/target/linux/kirkwood/image/Makefile
+++ b/target/linux/kirkwood/image/Makefile
@@ -184,6 +184,24 @@ define Device/iom_ix2-200
 endef
 TARGET_DEVICES += iom_ix2-200
 
+define Device/iom_ix4-200d
+  DEVICE_VENDOR := Iomega
+  DEVICE_MODEL := StorCenter ix4-200d
+  DEVICE_PACKAGES := kmod-ata-marvell-sata kmod-fs-ext4 \
+       kmod-gpio-button-hotplug kmod-gpio-nxp-74hc164 \
+       kmod-hwmon-adt7475 kmod-mvsdio kmod-spi-gpio
+  PAGESIZE := 512
+  SUBPAGESIZE := 256
+  BLOCKSIZE := 16k
+  KERNEL_SIZE := 3072k
+  KERNEL_IN_UBI :=
+  UBINIZE_OPTS := -E 5
+  IMAGE_SIZE := 31744k
+  IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi | \
+       check-size
+endef
+TARGET_DEVICES += iom_ix4-200d
+
 define Device/iptime_nas1
   DEVICE_VENDOR := ipTIME
   DEVICE_MODEL := NAS1