#define NUM_FBRS 2
#define MAX_PACKETS_HANDLED 256
+#define ET131X_MIN_MTU 64
+#define ET131X_MAX_MTU 9216
#define ALCATEL_MULTICAST_PKT 0x01000000
#define ALCATEL_BROADCAST_PKT 0x02000000
int result = 0;
struct et131x_adapter *adapter = netdev_priv(netdev);
- if (new_mtu < 64 || new_mtu > 9216)
- return -EINVAL;
-
et131x_disable_txrx(netdev);
netdev->mtu = new_mtu;
netdev->watchdog_timeo = ET131X_TX_TIMEOUT;
netdev->netdev_ops = &et131x_netdev_ops;
+ netdev->min_mtu = ET131X_MIN_MTU;
+ netdev->max_mtu = ET131X_MAX_MTU;
SET_NETDEV_DEV(netdev, &pdev->dev);
netdev->ethtool_ops = &et131x_ethtool_ops;
/* RX/TX MAC FIFO configs */
u32 tx_fifo_depth;
u32 rx_fifo_depth;
- u32 max_mtu;
/* Hash filter settings */
u32 hash_filter;
*/
static int tse_change_mtu(struct net_device *dev, int new_mtu)
{
- struct altera_tse_private *priv = netdev_priv(dev);
- unsigned int max_mtu = priv->max_mtu;
- unsigned int min_mtu = ETH_ZLEN + ETH_FCS_LEN;
-
if (netif_running(dev)) {
netdev_err(dev, "must be stopped to change its MTU\n");
return -EBUSY;
}
- if ((new_mtu < min_mtu) || (new_mtu > max_mtu)) {
- netdev_err(dev, "invalid MTU, max MTU is: %u\n", max_mtu);
- return -EINVAL;
- }
-
dev->mtu = new_mtu;
netdev_update_features(dev);
of_property_read_bool(pdev->dev.of_node,
"altr,has-supplementary-unicast");
+ priv->dev->min_mtu = ETH_ZLEN + ETH_FCS_LEN;
/* Max MTU is 1500, ETH_DATA_LEN */
- priv->max_mtu = ETH_DATA_LEN;
+ priv->dev->max_mtu = ETH_DATA_LEN;
/* Get the max mtu from the device tree. Note that the
* "max-frame-size" parameter is actually max mtu. Definition
* in the ePAPR v1.1 spec and usage differ, so go with usage.
*/
of_property_read_u32(pdev->dev.of_node, "max-frame-size",
- &priv->max_mtu);
+ &priv->dev->max_mtu);
/* The DMA buffer size already accounts for an alignment bias
* to avoid unaligned access exceptions for the NIOS processor,
struct amd8111e_priv *lp = netdev_priv(dev);
int err;
- if ((new_mtu < AMD8111E_MIN_MTU) || (new_mtu > AMD8111E_MAX_MTU))
- return -EINVAL;
-
if (!netif_running(dev)) {
/* new_mtu will be used
* when device starts netxt time
dev->ethtool_ops = &ops;
dev->irq =pdev->irq;
dev->watchdog_timeo = AMD8111E_TX_TIMEOUT;
+ dev->min_mtu = AMD8111E_MIN_MTU;
+ dev->max_mtu = AMD8111E_MAX_MTU;
netif_napi_add(dev, &lp->napi, amd8111e_rx_poll, 32);
#if AMD8111E_VLAN_TAG_USED
struct bnad *bnad = netdev_priv(netdev);
u32 rx_count = 0, frame, new_frame;
- if (new_mtu + ETH_HLEN < ETH_ZLEN || new_mtu > BNAD_JUMBO_MTU)
- return -EINVAL;
-
mutex_lock(&bnad->conf_mutex);
mtu = netdev->mtu;
netdev->mem_start = bnad->mmio_start;
netdev->mem_end = bnad->mmio_start + bnad->mmio_len - 1;
+ /* MTU range: 46 - 9000 */
+ netdev->min_mtu = ETH_ZLEN - ETH_HLEN;
+ netdev->max_mtu = BNAD_JUMBO_MTU;
+
netdev->netdev_ops = &bnad_netdev_ops;
bnad_set_ethtool_ops(netdev);
}
#define MACB_MAX_TX_LEN ((unsigned int)((1 << MACB_TX_FRMLEN_SIZE) - 1))
#define GEM_MAX_TX_LEN ((unsigned int)((1 << GEM_TX_FRMLEN_SIZE) - 1))
-#define GEM_MTU_MIN_SIZE 68
+#define GEM_MTU_MIN_SIZE ETH_MIN_MTU
#define MACB_WOL_HAS_MAGIC_PACKET (0x1 << 0)
#define MACB_WOL_ENABLED (0x1 << 1)
static int macb_change_mtu(struct net_device *dev, int new_mtu)
{
- struct macb *bp = netdev_priv(dev);
- u32 max_mtu;
-
if (netif_running(dev))
return -EBUSY;
- max_mtu = ETH_DATA_LEN;
- if (bp->caps & MACB_CAPS_JUMBO)
- max_mtu = gem_readl(bp, JML) - ETH_HLEN - ETH_FCS_LEN;
-
- if ((new_mtu > max_mtu) || (new_mtu < GEM_MTU_MIN_SIZE))
- return -EINVAL;
-
dev->mtu = new_mtu;
return 0;
goto err_out_free_netdev;
}
+ /* MTU range: 68 - 1500 or 10240 */
+ dev->min_mtu = GEM_MTU_MIN_SIZE;
+ if (bp->caps & MACB_CAPS_JUMBO)
+ dev->max_mtu = gem_readl(bp, JML) - ETH_HLEN - ETH_FCS_LEN;
+ else
+ dev->max_mtu = ETH_DATA_LEN;
+
mac = of_get_mac_address(np);
if (mac)
ether_addr_copy(bp->dev->dev_addr, mac);
};
/* XGMAC Configuration Settings */
-#define MAX_MTU 9000
+#define XGMAC_MAX_MTU 9000
#define PAUSE_TIME 0x400
#define DMA_RX_RING_SZ 256
*/
static int xgmac_change_mtu(struct net_device *dev, int new_mtu)
{
- struct xgmac_priv *priv = netdev_priv(dev);
- int old_mtu;
-
- if ((new_mtu < 46) || (new_mtu > MAX_MTU)) {
- netdev_err(priv->dev, "invalid MTU, max MTU is: %d\n", MAX_MTU);
- return -EINVAL;
- }
-
- old_mtu = dev->mtu;
-
- /* return early if the buffer sizes will not change */
- if (old_mtu == new_mtu)
- return 0;
-
/* Stop everything, get ready to change the MTU */
if (!netif_running(dev))
return 0;
ndev->features |= ndev->hw_features;
ndev->priv_flags |= IFF_UNICAST_FLT;
+ /* MTU range: 46 - 9000 */
+ ndev->min_mtu = ETH_ZLEN - ETH_HLEN;
+ ndev->max_mtu = XGMAC_MAX_MTU;
+
/* Get the MAC address */
xgmac_get_mac_addr(priv->base, ndev->dev_addr, 0);
if (!is_valid_ether_addr(ndev->dev_addr))
#define SPEED_INVALID 0xffff
#define DUPLEX_INVALID 0xff
+/* Max frame size PM3393 can handle. Includes Ethernet header and CRC. */
+#define PM3393_MAX_FRAME_SIZE 9600
+
+#define VSC7326_MAX_MTU 9600
+
enum {
CHBT_BOARD_N110,
CHBT_BOARD_N210,
if (!mac->ops->set_mtu)
return -EOPNOTSUPP;
- if (new_mtu < 68)
- return -EINVAL;
if ((ret = mac->ops->set_mtu(mac, new_mtu)))
return ret;
dev->mtu = new_mtu;
netif_napi_add(netdev, &adapter->napi, t1_poll, 64);
netdev->ethtool_ops = &t1_ethtool_ops;
+
+ switch (bi->board) {
+ case CHBT_BOARD_CHT110:
+ case CHBT_BOARD_N110:
+ case CHBT_BOARD_N210:
+ case CHBT_BOARD_CHT210:
+ netdev->max_mtu = PM3393_MAX_FRAME_SIZE -
+ (ETH_HLEN + ETH_FCS_LEN);
+ break;
+ case CHBT_BOARD_CHN204:
+ netdev->max_mtu = VSC7326_MAX_MTU;
+ break;
+ default:
+ netdev->max_mtu = ETH_DATA_LEN;
+ break;
+ }
}
if (t1_init_sw_modules(adapter, bi) < 0) {
#define OFFSET(REG_ADDR) ((REG_ADDR) << 2)
-/* Max frame size PM3393 can handle. Includes Ethernet header and CRC. */
-#define MAX_FRAME_SIZE 9600
-
#define IPG 12
#define TXXG_CONF1_VAL ((IPG << SUNI1x10GEXP_BITOFF_TXXG_IPGT) | \
SUNI1x10GEXP_BITMSK_TXXG_32BIT_ALIGN | SUNI1x10GEXP_BITMSK_TXXG_CRCEN | \
{
int enabled = cmac->instance->enabled;
- /* MAX_FRAME_SIZE includes header + FCS, mtu doesn't */
- mtu += 14 + 4;
- if (mtu > MAX_FRAME_SIZE)
- return -EINVAL;
+ mtu += ETH_HLEN + ETH_FCS_LEN;
/* Disable Rx/Tx MAC before configuring it. */
if (enabled)
/* 30 minutes for full statistics update */
#define MAJOR_UPDATE_TICKS (1800 / STATS_TICK_SECS)
-#define MAX_MTU 9600
-
/* The egress WM value 0x01a01fff should be used only when the
* interface is down (MAC port disabled). This is a workaround
* for disabling the T2/MAC flow-control. When the interface is
{
int port = mac->instance->index;
- if (mtu > MAX_MTU)
- return -EINVAL;
-
/* max_len includes header and FCS */
vsc_write(mac->adapter, REG_MAX_LEN(port), mtu + 14 + 4);
return 0;
struct enic *enic = netdev_priv(netdev);
int running = netif_running(netdev);
- if (new_mtu < ENIC_MIN_MTU || new_mtu > ENIC_MAX_MTU)
- return -EINVAL;
-
if (enic_is_dynamic(enic) || enic_is_sriov_vf(enic))
return -EOPNOTSUPP;
netdev->priv_flags |= IFF_UNICAST_FLT;
+ /* MTU range: 68 - 9000 */
+ netdev->min_mtu = ENIC_MIN_MTU;
+ netdev->max_mtu = ENIC_MAX_MTU;
+
err = register_netdev(netdev);
if (err) {
dev_err(dev, "Cannot register net device, aborting\n");
#define ENIC_MIN_RQ_DESCS 64
#define ENIC_MAX_RQ_DESCS 4096
-#define ENIC_MIN_MTU 68
+#define ENIC_MIN_MTU ETH_MIN_MTU
#define ENIC_MAX_MTU 9000
#define ENIC_MULTICAST_PERFECT_FILTERS 32
/* Fill in the dev structure */
dev->watchdog_timeo = TX_TIMEOUT;
+ /* MTU range: 50 - 9586 */
dev->mtu = 1500;
+ dev->min_mtu = 50;
+ dev->max_mtu = GFAR_JUMBO_FRAME_SIZE - ETH_HLEN;
dev->netdev_ops = &gfar_netdev_ops;
dev->ethtool_ops = &gfar_ethtool_ops;
static int gfar_change_mtu(struct net_device *dev, int new_mtu)
{
struct gfar_private *priv = netdev_priv(dev);
- int frame_size = new_mtu + ETH_HLEN;
-
- if ((frame_size < 64) || (frame_size > GFAR_JUMBO_FRAME_SIZE)) {
- netif_err(priv, drv, dev, "Invalid MTU setting\n");
- return -EINVAL;
- }
while (test_and_set_bit_lock(GFAR_RESETTING, &priv->state))
cpu_relax();
if (mac_cb->mac_type == HNAE_PORT_DEBUG)
max_frm = MAC_MAX_MTU_DBG;
- if ((new_mtu < MAC_MIN_MTU) || (new_frm > max_frm) ||
- (new_frm > HNS_RCB_RING_MAX_BD_PER_PKT * buf_size))
+ if (new_frm > HNS_RCB_RING_MAX_BD_PER_PKT * buf_size)
return -EINVAL;
if (!drv->config_max_frame_length)
#include "hnae.h"
#include "hns_enet.h"
+#include "hns_dsaf_mac.h"
#define NIC_MAX_Q_PER_VF 16
#define HNS_NIC_TX_TIMEOUT (5 * HZ)
struct hnae_handle *h = priv->ae_handle;
int ret;
- /* MTU < 68 is an error and causes problems on some kernels */
- if (new_mtu < 68)
- return -EINVAL;
-
if (!h->dev->ops->set_mtu)
return -ENOTSUPP;
NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM | NETIF_F_RXCSUM;
ndev->vlan_features |= NETIF_F_SG | NETIF_F_GSO | NETIF_F_GRO;
+ /* MTU range: 68 - 9578 (v1) or 9706 (v2) */
+ ndev->min_mtu = MAC_MIN_MTU;
switch (priv->enet_ver) {
case AE_VERSION_2:
ndev->features |= NETIF_F_TSO | NETIF_F_TSO6;
ndev->hw_features |= NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
NETIF_F_RXCSUM | NETIF_F_SG | NETIF_F_GSO |
NETIF_F_GRO | NETIF_F_TSO | NETIF_F_TSO6;
+ ndev->max_mtu = MAC_MAX_MTU_V2 -
+ (ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN);
break;
default:
+ ndev->max_mtu = MAC_MAX_MTU -
+ (ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN);
break;
}
if (hw->dev_count > 1)
if (dev != hw_priv->dev)
return 0;
- if (new_mtu < 60)
- return -EINVAL;
- if (dev->mtu != new_mtu) {
- hw_mtu = new_mtu + ETHERNET_HEADER_SIZE + 4;
- if (hw_mtu > MAX_RX_BUF_SIZE)
- return -EINVAL;
- if (hw_mtu > REGULAR_RX_BUF_SIZE) {
- hw->features |= RX_HUGE_FRAME;
- hw_mtu = MAX_RX_BUF_SIZE;
- } else {
- hw->features &= ~RX_HUGE_FRAME;
- hw_mtu = REGULAR_RX_BUF_SIZE;
- }
- hw_mtu = (hw_mtu + 3) & ~3;
- hw_priv->mtu = hw_mtu;
- dev->mtu = new_mtu;
+ hw_mtu = new_mtu + ETHERNET_HEADER_SIZE + 4;
+ if (hw_mtu > REGULAR_RX_BUF_SIZE) {
+ hw->features |= RX_HUGE_FRAME;
+ hw_mtu = MAX_RX_BUF_SIZE;
+ } else {
+ hw->features &= ~RX_HUGE_FRAME;
+ hw_mtu = REGULAR_RX_BUF_SIZE;
}
+ hw_mtu = (hw_mtu + 3) & ~3;
+ hw_priv->mtu = hw_mtu;
+ dev->mtu = new_mtu;
+
return 0;
}
dev->netdev_ops = &netdev_ops;
dev->ethtool_ops = &netdev_ethtool_ops;
+
+ /* MTU range: 60 - 1894 */
+ dev->min_mtu = ETH_ZLEN;
+ dev->max_mtu = MAX_RX_BUF_SIZE -
+ (ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN);
+
if (register_netdev(dev))
goto pcidev_init_reg_err;
port_set_power_saving(port, true);
struct myri10ge_priv *mgp = netdev_priv(dev);
int error = 0;
- if ((new_mtu < 68) || (ETH_HLEN + new_mtu > MYRI10GE_MAX_ETHER_MTU)) {
- netdev_err(dev, "new mtu (%d) is not valid\n", new_mtu);
- return -EINVAL;
- }
netdev_info(dev, "changing mtu from %d to %d\n", dev->mtu, new_mtu);
if (mgp->running) {
/* if we change the mtu on an active device, we must
myri10ge_setup_dca(mgp);
#endif
pci_set_drvdata(pdev, mgp);
- if ((myri10ge_initial_mtu + ETH_HLEN) > MYRI10GE_MAX_ETHER_MTU)
- myri10ge_initial_mtu = MYRI10GE_MAX_ETHER_MTU - ETH_HLEN;
- if ((myri10ge_initial_mtu + ETH_HLEN) < 68)
- myri10ge_initial_mtu = 68;
- netdev->netdev_ops = &myri10ge_netdev_ops;
+ /* MTU range: 68 - 9000 */
+ netdev->min_mtu = ETH_MIN_MTU;
+ netdev->max_mtu = MYRI10GE_MAX_ETHER_MTU - ETH_HLEN;
+
+ if (myri10ge_initial_mtu > netdev->max_mtu)
+ myri10ge_initial_mtu = netdev->max_mtu;
+ if (myri10ge_initial_mtu < netdev->min_mtu)
+ myri10ge_initial_mtu = netdev->min_mtu;
+
netdev->mtu = myri10ge_initial_mtu;
+
+ netdev->netdev_ops = &myri10ge_netdev_ops;
netdev->hw_features = mgp->features | NETIF_F_RXCSUM;
/* fake NETIF_F_HW_VLAN_CTAG_RX for good GRO performance */
dev->ethtool_ops = ðtool_ops;
+ /* MTU range: 64 - 2024 */
+ dev->min_mtu = ETH_ZLEN + ETH_FCS_LEN;
+ dev->max_mtu = NATSEMI_RX_LIMIT - NATSEMI_HEADERS;
+
if (mtu)
dev->mtu = mtu;
static int natsemi_change_mtu(struct net_device *dev, int new_mtu)
{
- if (new_mtu < 64 || new_mtu > NATSEMI_RX_LIMIT-NATSEMI_HEADERS)
- return -EINVAL;
-
dev->mtu = new_mtu;
/* synchronized against open : rtnl_lock() held by caller */
struct nfp_net_rx_ring *tmp_rings;
int err;
- if (new_mtu < 68 || new_mtu > nn->max_mtu) {
- nn_err(nn, "New MTU (%d) is not valid\n", new_mtu);
- return -EINVAL;
- }
-
old_mtu = netdev->mtu;
old_fl_bufsz = nn->fl_bufsz;
new_fl_bufsz = NFP_NET_MAX_PREPEND + ETH_HLEN + VLAN_HLEN * 2 + new_mtu;
ether_setup(netdev);
netdev->netdev_ops = &nfp_net_netdev_ops;
netdev->watchdog_timeo = msecs_to_jiffies(5 * 1000);
+
+ /* MTU range: 68 - hw-specific max */
+ netdev->min_mtu = ETH_MIN_MTU;
+ netdev->max_mtu = nn->max_mtu;
+
netif_carrier_off(netdev);
nfp_net_set_ethtool_ops(netdev);
struct fe_priv *np = netdev_priv(dev);
int old_mtu;
- if (new_mtu < 64 || new_mtu > np->pkt_limit)
- return -EINVAL;
-
old_mtu = dev->mtu;
dev->mtu = new_mtu;
/* return early if the buffer sizes will not change */
if (old_mtu <= ETH_DATA_LEN && new_mtu <= ETH_DATA_LEN)
return 0;
- if (old_mtu == new_mtu)
- return 0;
/* synchronized against open : rtnl_lock() held by caller */
if (netif_running(dev)) {
/* Add loopback capability to the device. */
dev->hw_features |= NETIF_F_LOOPBACK;
+ /* MTU range: 64 - 1500 or 9100 */
+ dev->min_mtu = ETH_ZLEN + ETH_FCS_LEN;
+ dev->max_mtu = np->pkt_limit;
+
np->pause_flags = NV_PAUSEFRAME_RX_CAPABLE | NV_PAUSEFRAME_RX_REQ | NV_PAUSEFRAME_AUTONEG;
if ((id->driver_data & DEV_HAS_PAUSEFRAME_TX_V1) ||
(id->driver_data & DEV_HAS_PAUSEFRAME_TX_V2) ||
static int pch_gbe_change_mtu(struct net_device *netdev, int new_mtu)
{
struct pch_gbe_adapter *adapter = netdev_priv(netdev);
- int max_frame;
+ int max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
unsigned long old_rx_buffer_len = adapter->rx_buffer_len;
int err;
- max_frame = new_mtu + ETH_HLEN + ETH_FCS_LEN;
- if ((max_frame < ETH_ZLEN + ETH_FCS_LEN) ||
- (max_frame > PCH_GBE_MAX_JUMBO_FRAME_SIZE)) {
- netdev_err(netdev, "Invalid MTU setting\n");
- return -EINVAL;
- }
if (max_frame <= PCH_GBE_FRAME_SIZE_2048)
adapter->rx_buffer_len = PCH_GBE_FRAME_SIZE_2048;
else if (max_frame <= PCH_GBE_FRAME_SIZE_4096)
netdev->features = netdev->hw_features;
pch_gbe_set_ethtool_ops(netdev);
+ /* MTU range: 46 - 10300 */
+ netdev->min_mtu = ETH_ZLEN - ETH_HLEN;
+ netdev->max_mtu = PCH_GBE_MAX_JUMBO_FRAME_SIZE -
+ (ETH_HLEN + ETH_FCS_LEN);
+
pch_gbe_mac_load_mac_addr(&adapter->hw);
pch_gbe_mac_reset_hw(&adapter->hw);
* - Multiqueue RX/TX
*/
-#define PE_MIN_MTU 64
+#define PE_MIN_MTU (ETH_ZLEN + ETH_HLEN)
#define PE_MAX_MTU 9000
#define PE_DEF_MTU ETH_DATA_LEN
int running;
int ret = 0;
- if (new_mtu < PE_MIN_MTU || new_mtu > PE_MAX_MTU)
- return -EINVAL;
-
running = netif_running(dev);
if (running) {
}
/* Setup checksum channels if large MTU and none already allocated */
- if (new_mtu > 1500 && !mac->num_cs) {
+ if (new_mtu > PE_DEF_MTU && !mac->num_cs) {
pasemi_mac_setup_csrings(mac);
if (!mac->num_cs) {
ret = -ENOMEM;
dev->netdev_ops = &pasemi_netdev_ops;
dev->mtu = PE_DEF_MTU;
+
+ /* MTU range: 64 - 9000 */
+ dev->min_mtu = PE_MIN_MTU;
+ dev->max_mtu = PE_MAX_MTU;
+
/* 1500 MTU + ETH_HLEN + VLAN_HLEN + 2 64B cachelines */
mac->bufsz = dev->mtu + ETH_HLEN + ETH_FCS_LEN + LOCAL_SKB_ALIGN + 128;
/* Frame length is invalid */
#define QCAFRM_INVFRAME (QCAFRM_ERR_BASE - 4)
-/* Min/Max Ethernet MTU */
-#define QCAFRM_ETHMINMTU 46
-#define QCAFRM_ETHMAXMTU 1500
+/* Min/Max Ethernet MTU: 46/1500 */
+#define QCAFRM_ETHMINMTU (ETH_ZLEN - ETH_HLEN)
+#define QCAFRM_ETHMAXMTU ETH_DATA_LEN
/* Min/Max frame lengths */
#define QCAFRM_ETHMINLEN (QCAFRM_ETHMINMTU + ETH_HLEN)
dev_kfree_skb(qca->rx_skb);
}
-static int
-qcaspi_netdev_change_mtu(struct net_device *dev, int new_mtu)
-{
- if ((new_mtu < QCAFRM_ETHMINMTU) || (new_mtu > QCAFRM_ETHMAXMTU))
- return -EINVAL;
-
- dev->mtu = new_mtu;
-
- return 0;
-}
-
static const struct net_device_ops qcaspi_netdev_ops = {
.ndo_init = qcaspi_netdev_init,
.ndo_uninit = qcaspi_netdev_uninit,
.ndo_open = qcaspi_netdev_open,
.ndo_stop = qcaspi_netdev_close,
.ndo_start_xmit = qcaspi_netdev_xmit,
- .ndo_change_mtu = qcaspi_netdev_change_mtu,
.ndo_set_mac_address = eth_mac_addr,
.ndo_tx_timeout = qcaspi_netdev_tx_timeout,
.ndo_validate_addr = eth_validate_addr,
dev->priv_flags &= ~IFF_TX_SKB_SHARING;
dev->tx_queue_len = 100;
+ /* MTU range: 46 - 1500 */
+ dev->min_mtu = QCAFRM_ETHMINMTU;
+ dev->max_mtu = QCAFRM_ETHMAXMTU;
+
qca = netdev_priv(dev);
memset(qca, 0, sizeof(struct qcaspi));
int running = netif_running(dev);
int err;
-#define ROCKER_PORT_MIN_MTU 68
-#define ROCKER_PORT_MAX_MTU 9000
-
- if (new_mtu < ROCKER_PORT_MIN_MTU || new_mtu > ROCKER_PORT_MAX_MTU)
- return -EINVAL;
-
if (running)
rocker_port_stop(dev);
}
}
+#define ROCKER_PORT_MIN_MTU ETH_MIN_MTU
+#define ROCKER_PORT_MAX_MTU 9000
static int rocker_probe_port(struct rocker *rocker, unsigned int port_number)
{
const struct pci_dev *pdev = rocker->pdev;
dev->features |= NETIF_F_NETNS_LOCAL | NETIF_F_SG;
+ /* MTU range: 68 - 9000 */
+ dev->min_mtu = ROCKER_PORT_MIN_MTU;
+ dev->max_mtu = ROCKER_PORT_MAX_MTU;
+
err = rocker_world_port_pre_init(rocker_port);
if (err) {
dev_err(&pdev->dev, "port world pre-init failed\n");
*/
static int sxgbe_change_mtu(struct net_device *dev, int new_mtu)
{
- /* RFC 791, page 25, "Every internet module must be able to forward
- * a datagram of 68 octets without further fragmentation."
- */
- if (new_mtu < MIN_MTU || (new_mtu > MAX_MTU)) {
- netdev_err(dev, "invalid MTU, MTU should be in between %d and %d\n",
- MIN_MTU, MAX_MTU);
- return -EINVAL;
- }
-
- /* Return if the buffer sizes will not change */
- if (dev->mtu == new_mtu)
- return 0;
-
dev->mtu = new_mtu;
if (!netif_running(dev))
/* assign filtering support */
ndev->priv_flags |= IFF_UNICAST_FLT;
+ /* MTU range: 68 - 9000 */
+ ndev->min_mtu = MIN_MTU;
+ ndev->max_mtu = MAX_MTU;
+
priv->msg_enable = netif_msg_init(debug, default_msg_level);
/* Enable TCP segmentation offload for all DMA channels */
*/
static int stmmac_change_mtu(struct net_device *dev, int new_mtu)
{
- struct stmmac_priv *priv = netdev_priv(dev);
- int max_mtu;
-
if (netif_running(dev)) {
pr_err("%s: must be stopped to change its MTU\n", dev->name);
return -EBUSY;
}
- if ((priv->plat->enh_desc) || (priv->synopsys_id >= DWMAC_CORE_4_00))
- max_mtu = JUMBO_LEN;
- else
- max_mtu = SKB_MAX_HEAD(NET_SKB_PAD + NET_IP_ALIGN);
-
- if (priv->plat->maxmtu < max_mtu)
- max_mtu = priv->plat->maxmtu;
-
- if ((new_mtu < 46) || (new_mtu > max_mtu)) {
- pr_err("%s: invalid MTU, max MTU is: %d\n", dev->name, max_mtu);
- return -EINVAL;
- }
-
dev->mtu = new_mtu;
netdev_update_features(dev);
#endif
priv->msg_enable = netif_msg_init(debug, default_msg_level);
+ /* MTU range: 46 - hw-specific max */
+ ndev->min_mtu = ETH_ZLEN - ETH_HLEN;
+ if ((priv->plat->enh_desc) || (priv->synopsys_id >= DWMAC_CORE_4_00))
+ ndev->max_mtu = JUMBO_LEN;
+ else
+ ndev->max_mtu = SKB_MAX_HEAD(NET_SKB_PAD + NET_IP_ALIGN);
+ if (priv->plat->maxmtu < ndev->max_mtu)
+ ndev->max_mtu = priv->plat->maxmtu;
+
if (flow_ctrl)
priv->flow_ctrl = FLOW_AUTO; /* RX/TX pause on */
{
ENTER;
- if (new_mtu == ndev->mtu)
- RET(0);
-
- /* enforce minimum frame size */
- if (new_mtu < ETH_ZLEN) {
- netdev_err(ndev, "mtu %d is less then minimal %d\n",
- new_mtu, ETH_ZLEN);
- RET(-EINVAL);
- }
-
ndev->mtu = new_mtu;
if (netif_running(ndev)) {
bdx_close(ndev);
#ifdef BDX_LLTX
ndev->features |= NETIF_F_LLTX;
#endif
+ /* MTU range: 60 - 16384 */
+ ndev->min_mtu = ETH_ZLEN;
+ ndev->max_mtu = BDX_MAX_MTU;
+
spin_lock_init(&priv->tx_lock);
/*bdx_hw_reset(priv); */
* ifcontig eth1 txqueuelen 3000 - to change it at runtime */
#define BDX_NDEV_TXQ_LEN 3000
+/* Max MTU for Jumbo Frame mode, per tehutinetworks.net Features FAQ is 16k */
+#define BDX_MAX_MTU (16 * 1024)
+
#define FIFO_SIZE 4096
#define FIFO_EXTRA_SPACE 1024
return (ret == 0) ? 0 : err;
}
-static int netcp_ndo_change_mtu(struct net_device *ndev, int new_mtu)
-{
- struct netcp_intf *netcp = netdev_priv(ndev);
-
- /* MTU < 68 is an error for IPv4 traffic */
- if ((new_mtu < 68) ||
- (new_mtu > (NETCP_MAX_FRAME_SIZE - ETH_HLEN - ETH_FCS_LEN))) {
- dev_err(netcp->ndev_dev, "Invalid mtu size = %d\n", new_mtu);
- return -EINVAL;
- }
-
- ndev->mtu = new_mtu;
- return 0;
-}
-
static void netcp_ndo_tx_timeout(struct net_device *ndev)
{
struct netcp_intf *netcp = netdev_priv(ndev);
.ndo_start_xmit = netcp_ndo_start_xmit,
.ndo_set_rx_mode = netcp_set_rx_mode,
.ndo_do_ioctl = netcp_ndo_ioctl,
- .ndo_change_mtu = netcp_ndo_change_mtu,
.ndo_set_mac_address = eth_mac_addr,
.ndo_validate_addr = eth_validate_addr,
.ndo_vlan_rx_add_vid = netcp_rx_add_vid,
ndev->hw_features = ndev->features;
ndev->vlan_features |= NETIF_F_SG;
+ /* MTU range: 68 - 9486 */
+ ndev->min_mtu = ETH_MIN_MTU;
+ ndev->max_mtu = NETCP_MAX_FRAME_SIZE - (ETH_HLEN + ETH_FCS_LEN);
+
netcp = netdev_priv(ndev);
spin_lock_init(&netcp->lock);
INIT_LIST_HEAD(&netcp->module_head);
struct velocity_info *vptr = netdev_priv(dev);
int ret = 0;
- if ((new_mtu < VELOCITY_MIN_MTU) || new_mtu > (VELOCITY_MAX_MTU)) {
- VELOCITY_PRT(MSG_LEVEL_ERR, KERN_NOTICE "%s: Invalid MTU.\n",
- vptr->netdev->name);
- ret = -EINVAL;
- goto out_0;
- }
-
if (!netif_running(dev)) {
dev->mtu = new_mtu;
goto out_0;
NETIF_F_HW_VLAN_CTAG_FILTER | NETIF_F_HW_VLAN_CTAG_RX |
NETIF_F_IP_CSUM;
+ /* MTU range: 64 - 9000 */
+ netdev->min_mtu = VELOCITY_MIN_MTU;
+ netdev->max_mtu = VELOCITY_MAX_MTU;
+
ret = register_netdev(netdev);
if (ret < 0)
goto err_iounmap;
#endif
int mtu_overhead = ETH_HLEN + ETH_FCS_LEN + vlan_bytes;
- /*
- * Limit the MTU to make sure the ethernet packets are between
- * 64 bytes and 65535 bytes.
- */
- if ((new_mtu + mtu_overhead < VLAN_ETH_ZLEN) ||
- (new_mtu + mtu_overhead > OCTEON_MAX_MTU)) {
- pr_err("MTU must be between %d and %d.\n",
- VLAN_ETH_ZLEN - mtu_overhead,
- OCTEON_MAX_MTU - mtu_overhead);
- return -EINVAL;
- }
dev->mtu = new_mtu;
if ((interface < 2) &&
dev->ethtool_ops = &cvm_oct_ethtool_ops;
cvm_oct_set_mac_filter(dev);
- dev->netdev_ops->ndo_change_mtu(dev, dev->mtu);
+ dev_set_mtu(dev, dev->mtu);
/*
* Zero out stats for port so we won't mistakenly show
int fau = FAU_NUM_PACKET_BUFFERS_TO_FREE;
int qos;
struct device_node *pip;
+ int mtu_overhead = ETH_HLEN + ETH_FCS_LEN;
+
+#if IS_ENABLED(CONFIG_VLAN_8021Q)
+ mtu_overhead += VLAN_HLEN;
+#endif
octeon_mdiobus_force_mod_depencency();
strcpy(dev->name, "pow%d");
for (qos = 0; qos < 16; qos++)
skb_queue_head_init(&priv->tx_free_list[qos]);
+ dev->min_mtu = VLAN_ETH_ZLEN - mtu_overhead;
+ dev->max_mtu = OCTEON_MAX_MTU - mtu_overhead;
if (register_netdev(dev) < 0) {
pr_err("Failed to register ethernet device for POW\n");
for (qos = 0; qos < cvmx_pko_get_num_queues(port);
qos++)
cvmx_fau_atomic_write32(priv->fau + qos * 4, 0);
+ dev->min_mtu = VLAN_ETH_ZLEN - mtu_overhead;
+ dev->max_mtu = OCTEON_MAX_MTU - mtu_overhead;
switch (priv->imode) {
/* These types don't support ports to IPD/PKO */
projects / openwrt / staging / blogic.git / commitdiff