qualcommax: ipq60xx: Add 8devices Mango DVK
authorMantas Pucka <mantas@8devices.com>
Mon, 22 Jan 2024 09:28:32 +0000 (11:28 +0200)
committerRobert Marko <robimarko@gmail.com>
Wed, 21 Feb 2024 20:42:23 +0000 (21:42 +0100)
8devices Mango DVK is a single board computer / devkit for 8devices Mango
system-on-module (SoM).

Specifications:
* CPU: Qualcomm IPQ6010 Quad core Cortex-A53 1.8GHz
* RAM: 512 MB
* Storage:
    * 32 MB serial NOR flash (on SoM)
    * 256 MB parallel NAND flash (on DVK)
* Ethernet:
    * 2x1G RJ45 ports(QCA8072 or QCA8075)
    * 1x2.5G RJ45 port (QCA8081)
    * 1xSFP (shares SGMII with QCA8081)
* Switch: Qualcomm Atheros IPQ6010
* WLAN:
    * 2.4GHz: QCN5121 2x2 802.11b/g/n/ax 574 Mbps PHY rate
    * 5GHz: QCN5152 2x2 802.11a/n/ac/ax 1201 Mbps PHY rate
* USB:
    * 1x USB3.0 Type-A port
    * 1x USB2.0 available at mini PCIe slot
* PCIe: 1x mini PCIe slot 1xLane Gen3 (8GT/s)
* SD/eMMC (on a single shared bus - only one can be active):
    * micro SD slot
    * eMMC module connector
* LEDs:
    * Green power led (not controllable)
    * Green 2.4GHz radio led (GPIO 67)
    * Green 5GHz radio led (GPIO 66)
* Buttons:
    * 1x (WPS GPIO79) button
* GPIOs: 2.54mm header brings out 18 GPIOs (1.8V level)
* UART: 4-pin UART header (3.3V level)
    * 115200 8N1, 3.3V-Tx-Rx-GND (3.3V is pin 1 close to boot-switch SW2)
* Power:
    * PoE IN on 2.5G port (passive 24-48V)
    * DC power terminal (12-58V)

Installation instructions:

Vendor image format is compatible with squashfs-sysupgrade image. Run:

sysupgrade -n -F openwrt-qualcommax-ipq60xx-8devices_mango-dvk-squashfs-sysupgrade.bin

Signed-off-by: Mantas Pucka <mantas@8devices.com>
package/boot/uboot-envtools/files/qualcommax_ipq60xx [new file with mode: 0644]
target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6010-mango-dvk.dts [new file with mode: 0644]
target/linux/qualcommax/image/ipq60xx.mk
target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network [new file with mode: 0644]
target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata [new file with mode: 0644]
target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh [new file with mode: 0644]

diff --git a/package/boot/uboot-envtools/files/qualcommax_ipq60xx b/package/boot/uboot-envtools/files/qualcommax_ipq60xx
new file mode 100644 (file)
index 0000000..df19a30
--- /dev/null
@@ -0,0 +1,22 @@
+[ -e /etc/config/ubootenv ] && exit 0
+
+touch /etc/config/ubootenv
+
+. /lib/uboot-envtools.sh
+. /lib/functions.sh
+
+board=$(board_name)
+
+case "$board" in
+8devices,mango-dvk|\
+8devices,mango-dvk-sfp)
+       idx="$(find_mtd_index 0:APPSBLENV)"
+       [ -n "$idx" ] && \
+               ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x10000" "0x10000"
+       ;;
+esac
+
+config_load ubootenv
+config_foreach ubootenv_add_app_config
+
+exit 0
diff --git a/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6010-mango-dvk.dts b/target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq6010-mango-dvk.dts
new file mode 100644 (file)
index 0000000..2724752
--- /dev/null
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "ipq6018.dtsi"
+#include "ipq6018-cp-cpu.dtsi"
+#include "ipq6018-ess.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+       model = "8devices Mango-DVK";
+       compatible = "8devices,mango-dvk", "qcom,ipq6018";
+
+       aliases {
+               serial0 = &blsp1_uart3;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               wps {
+                       label = "wps";
+                       gpios = <&tlmm 79 GPIO_ACTIVE_LOW>;
+                       linux,code = <KEY_WPS_BUTTON>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+               pinctrl-0 = <&led_pins>;
+               pinctrl-names = "default";
+
+               wlan5g {
+                       color = <LED_COLOR_ID_GREEN>;
+                       function = LED_FUNCTION_WLAN;
+                       function-enumerator = <0>;
+                       gpios = <&tlmm 66 GPIO_ACTIVE_HIGH>;
+                       linux,default-trigger = "phy0radio";
+               };
+
+               wlan2g {
+                       color = <LED_COLOR_ID_GREEN>;
+                       function = LED_FUNCTION_WLAN;
+                       function-enumerator = <1>;
+                       gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+                       linux,default-trigger = "phy1radio";
+               };
+       };
+};
+
+&tlmm {
+       mdio_pins: mdio-pins {
+               mdc {
+                       pins = "gpio64";
+                       function = "mdc";
+                       drive-strength = <8>;
+                       bias-pull-up;
+               };
+
+               mdio {
+                       pins = "gpio65";
+                       function = "mdio";
+                       drive-strength = <8>;
+                       bias-pull-up;
+               };
+       };
+
+       spi_0_pins: spi-0-pins {
+               pins = "gpio38", "gpio39", "gpio40", "gpio41";
+               function = "blsp0_spi";
+               drive-strength = <8>;
+               bias-pull-down;
+       };
+
+       led_pins: led_pins {
+               leds {
+                       pins = "gpio66", "gpio67";
+                       function = "gpio";
+                       drive-strength = <8>;
+                       bias-pull-down;
+               };
+       };
+
+       sd_pins: sd_pins {
+               sd_cd {
+                        pins = "gpio62";
+                        function = "gpio";
+                        drive-strength = <8>;
+                        bias-pull-up;
+               };
+       };
+};
+
+&blsp1_uart3 {
+       pinctrl-0 = <&serial_3_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+};
+
+&blsp1_spi1 {
+       pinctrl-0 = <&spi_0_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+
+       flash@0 {
+               #address-cells = <1>;
+               #size-cells = <1>;
+               reg = <0>;
+               compatible = "jedec,spi-nor";
+               spi-max-frequency = <25000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "0:SBL1";
+                               reg = <0x00000000 0x000c0000>;
+                       };
+
+                       partition@c0000 {
+                               label = "0:MIBIB";
+                               reg = <0x000c0000 0x00010000>;
+                       };
+
+                       partition@d0000 {
+                               label = "0:QSEE";
+                               reg = <0x000d0000 0x001a0000>;
+                       };
+
+                       partition@270000 {
+                               label = "0:DEVCFG";
+                               reg = <0x00270000 0x00010000>;
+                       };
+
+                       partition@280000 {
+                               label = "0:RPM";
+                               reg = <0x00280000 0x00020000>;
+                       };
+
+                       partition@2a0000 {
+                               label = "0:CDT";
+                               reg = <0x002a0000 0x00010000>;
+                       };
+
+                       partition@2b0000 {
+                               label = "0:APPSBLENV";
+                               reg = <0x002b0000 0x00010000>;
+                       };
+
+                       partition@2c0000 {
+                               label = "0:APPSBL";
+                               reg = <0x002c0000 0x000a0000>;
+                       };
+
+                       partition@360000 {
+                               compatible = "nvmem-cells";
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+                               label = "0:ART";
+                               reg = <0x00360000 0x00040000>;
+
+                               macaddr_eth0: macaddr@0 {
+                                       reg = <0x0 0x6>;
+                               };
+
+                               macaddr_eth1: macaddr@6 {
+                                       reg = <0x6 0x6>;
+                               };
+
+                               macaddr_eth2: macaddr@c {
+                                       reg = <0xc 0x6>;
+                               };
+                       };
+
+                       partition@3a0000 {
+                               label = "config";
+                               reg = <0x003a0000 0x00040000>;
+                       };
+
+                       partition@3e0000 {
+                               label = "data";
+                               reg = <0x003e0000 0x00100000>;
+                       };
+
+                       partition@4e0000 {
+                               label = "firmware";
+                               compatible = "denx,fit";
+                               reg = <0x004e0000 0x1b20000>;
+                       };
+               };
+       };
+};
+
+&dp3 {
+       status = "okay";
+
+       phy-handle = <&qca8072_1>;
+       nvmem-cells = <&macaddr_eth1>;
+       nvmem-cell-names = "mac-address";
+       label = "lan2";
+};
+
+&dp4 {
+       status = "okay";
+
+       phy-handle = <&qca8072_0>;
+       nvmem-cells = <&macaddr_eth0>;
+       nvmem-cell-names = "mac-address";
+       label = "lan1";
+};
+
+&dp5 {
+       status = "okay";
+
+       phy-handle = <&qca8081>;
+       nvmem-cells = <&macaddr_eth2>;
+       nvmem-cell-names = "mac-address";
+       label = "wan";
+};
+
+&edma {
+       status = "okay";
+};
+
+&mdio {
+       status = "okay";
+       pinctrl-0 = <&mdio_pins>;
+       pinctrl-names = "default";
+       reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>;
+       reset-delay-us = <10000>;
+       reset-post-delay-us = <50000>;
+
+       ethernet-phy-package@0 {
+               #address-cells = <1>;
+               #size-cells = <0>;
+               compatible = "qcom,qca8075-package";
+               reg = <0>;
+
+               qcom,package-mode = "psgmii";
+
+               qca8072_0: ethernet-phy@3 {
+                       compatible = "ethernet-phy-ieee802.3-c22";
+                       reg = <3>;
+               };
+
+               qca8072_1: ethernet-phy@4 {
+                       compatible = "ethernet-phy-ieee802.3-c22";
+                       reg = <4>;
+               };
+       };
+
+       qca8081: ethernet-phy@24 {
+               compatible = "ethernet-phy-id004d.d101";
+               reg = <24>;
+               reset-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>;
+       };
+};
+
+&sdhc_1 {
+       pinctrl-0 = <&sd_pins>;
+       pinctrl-names = "default";
+       status = "okay";
+
+       vqmmc-supply = <&ipq6018_l2>;
+       cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+};
+
+&switch {
+       status = "okay";
+
+       switch_lan_bmp = <(ESS_PORT3 | ESS_PORT4)>;
+       switch_wan_bmp = <ESS_PORT5>;
+       switch_mac_mode = <MAC_MODE_PSGMII>;
+       switch_mac_mode1 = <MAC_MODE_SGMII_PLUS>;
+       port3_pcs_channel = <4>;
+
+       qcom,port_phyinfo {
+               port@3 {
+                       port_id = <3>;
+                       phy_address = <4>;
+               };
+               port@4 {
+                       port_id = <4>;
+                       phy_address = <3>;
+               };
+               port@5 {
+                       port_id = <5>;
+                       phy_address = <24>;
+                       port_mac_sel = "QGMAC_PORT";
+               };
+       };
+};
+
+&qpic_bam {
+       status = "okay";
+};
+
+&qpic_nand {
+       status = "okay";
+
+       nand@0 {
+               reg = <0>;
+
+               nand-ecc-strength = <4>;
+               nand-ecc-step-size = <512>;
+               nand-bus-width = <8>;
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "nand_data";
+                               reg = <0x0000000 0x10000000>;
+                       };
+               };
+       };
+};
+
+&pcie_phy {
+       status = "okay";
+};
+
+&pcie0 {
+       status = "okay";
+       perst-gpio = <&tlmm 60 GPIO_ACTIVE_LOW>;
+};
+
+&wifi {
+       status = "okay";
+       qcom,ath11k-calibration-variant = "8devices-Mango";
+};
+
+&qusb_phy_1 {
+       status = "okay";
+};
+
+&usb2 {
+       status = "okay";
+};
+
+&qusb_phy_0 {
+       status = "okay";
+};
+
+&ssphy_0 {
+       status = "okay";
+};
+
+&usb3 {
+       status = "okay";
+};
index e69de29bb2d1d6434b8b29ae775ad8c2e48c5391..00dead93ad1f2984dfcd154d5fb04b5ab2fd9273 100644 (file)
@@ -0,0 +1,12 @@
+define Device/8devices_mango-dvk
+       $(call Device/FitImageLzma)
+       DEVICE_VENDOR := 8devices
+       DEVICE_MODEL := Mango-DVK
+       IMAGE_SIZE := 27776k
+       BLOCKSIZE := 64k
+       SOC := ipq6010
+       SUPPORTED_DEVICES += 8devices,mango
+       IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | check-size | append-metadata
+       DEVICE_PACKAGES := ipq-wifi-8devices_mango
+endef
+TARGET_DEVICES += 8devices_mango-dvk
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network b/target/linux/qualcommax/ipq60xx/base-files/etc/board.d/02_network
new file mode 100644 (file)
index 0000000..081d894
--- /dev/null
@@ -0,0 +1,28 @@
+#
+# Copyright (c) 2015 The Linux Foundation. All rights reserved.
+# Copyright (c) 2011-2015 OpenWrt.org
+#
+
+. /lib/functions/uci-defaults.sh
+. /lib/functions/system.sh
+
+ipq60xx_setup_interfaces()
+{
+       local board="$1"
+
+       case "$board" in
+       8devices,mango-dvk)
+               ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
+               ;;
+       *)
+               echo "Unsupported hardware. Network interfaces not initialized"
+               ;;
+       esac
+}
+
+board_config_update
+board=$(board_name)
+ipq60xx_setup_interfaces $board
+board_config_flush
+
+exit 0
diff --git a/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata b/target/linux/qualcommax/ipq60xx/base-files/etc/hotplug.d/firmware/11-ath11-caldata
new file mode 100644 (file)
index 0000000..c14722c
--- /dev/null
@@ -0,0 +1,20 @@
+#!/bin/sh
+
+[ -e /lib/firmware/$FIRMWARE ] && exit 0
+
+. /lib/functions/caldata.sh
+
+board=$(board_name)
+
+case "$FIRMWARE" in
+"ath11k/IPQ6018/hw1.0/cal-ahb-c000000.wifi.bin")
+       case "$board" in
+       8devices,mango-dvk)
+               caldata_extract "0:ART" 0x1000 0x20000
+               ;;
+       esac
+       ;;
+*)
+       exit 1
+       ;;
+esac
diff --git a/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh b/target/linux/qualcommax/ipq60xx/base-files/lib/upgrade/platform.sh
new file mode 100644 (file)
index 0000000..3d3c17b
--- /dev/null
@@ -0,0 +1,17 @@
+PART_NAME=firmware
+REQUIRE_IMAGE_METADATA=1
+
+RAMFS_COPY_BIN='fw_printenv fw_setenv head'
+RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
+
+platform_check_image() {
+       return 0;
+}
+
+platform_do_upgrade() {
+       case "$(board_name)" in
+       *)
+               default_do_upgrade "$1"
+               ;;
+       esac
+}