*
*/
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/clk/at91_pmc.h>
-
-#include <asm/proc-fns.h>
-#include <asm/irq.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
#include <asm/system_misc.h>
-#include <mach/at91sam9263.h>
#include <mach/hardware.h>
-#include "at91_aic.h"
#include "soc.h"
#include "generic.h"
-#include "sam9_smc.h"
-#include "pm.h"
-
-#if defined(CONFIG_OLD_CLK_AT91)
-#include "clock.h"
-/* --------------------------------------------------------------------
- * Clocks
- * -------------------------------------------------------------------- */
-
-/*
- * The peripheral clocks.
- */
-static struct clk pioA_clk = {
- .name = "pioA_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_PIOA,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioB_clk = {
- .name = "pioB_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_PIOB,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk pioCDE_clk = {
- .name = "pioCDE_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_PIOCDE,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart0_clk = {
- .name = "usart0_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_US0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart1_clk = {
- .name = "usart1_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_US1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk usart2_clk = {
- .name = "usart2_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_US2,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc0_clk = {
- .name = "mci0_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_MCI0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk mmc1_clk = {
- .name = "mci1_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_MCI1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk can_clk = {
- .name = "can_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_CAN,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk twi_clk = {
- .name = "twi_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_TWI,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi0_clk = {
- .name = "spi0_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_SPI0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk spi1_clk = {
- .name = "spi1_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_SPI1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc0_clk = {
- .name = "ssc0_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_SSC0,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ssc1_clk = {
- .name = "ssc1_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_SSC1,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ac97_clk = {
- .name = "ac97_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_AC97C,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk tcb_clk = {
- .name = "tcb_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_TCB,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk pwm_clk = {
- .name = "pwm_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_PWMC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk macb_clk = {
- .name = "pclk",
- .pmc_mask = 1 << AT91SAM9263_ID_EMAC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk dma_clk = {
- .name = "dma_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_DMA,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk twodge_clk = {
- .name = "2dge_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_2DGE,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk udc_clk = {
- .name = "udc_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_UDP,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk isi_clk = {
- .name = "isi_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_ISI,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk lcdc_clk = {
- .name = "lcdc_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_LCDC,
- .type = CLK_TYPE_PERIPHERAL,
-};
-static struct clk ohci_clk = {
- .name = "ohci_clk",
- .pmc_mask = 1 << AT91SAM9263_ID_UHP,
- .type = CLK_TYPE_PERIPHERAL,
-};
-
-static struct clk *periph_clocks[] __initdata = {
- &pioA_clk,
- &pioB_clk,
- &pioCDE_clk,
- &usart0_clk,
- &usart1_clk,
- &usart2_clk,
- &mmc0_clk,
- &mmc1_clk,
- &can_clk,
- &twi_clk,
- &spi0_clk,
- &spi1_clk,
- &ssc0_clk,
- &ssc1_clk,
- &ac97_clk,
- &tcb_clk,
- &pwm_clk,
- &macb_clk,
- &twodge_clk,
- &udc_clk,
- &isi_clk,
- &lcdc_clk,
- &dma_clk,
- &ohci_clk,
- // irq0 .. irq1
-};
-
-static struct clk_lookup periph_clocks_lookups[] = {
- /* One additional fake clock for macb_hclk */
- CLKDEV_CON_ID("hclk", &macb_clk),
- CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.0", &ssc0_clk),
- CLKDEV_CON_DEV_ID("pclk", "at91rm9200_ssc.1", &ssc1_clk),
- CLKDEV_CON_DEV_ID("pclk", "fff98000.ssc", &ssc0_clk),
- CLKDEV_CON_DEV_ID("pclk", "fff9c000.ssc", &ssc1_clk),
- CLKDEV_CON_DEV_ID("hclk", "at91sam9263-lcdfb.0", &lcdc_clk),
- CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk),
- CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk),
- CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
- CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
- CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),
- CLKDEV_CON_DEV_ID(NULL, "i2c-at91sam9260.0", &twi_clk),
- CLKDEV_CON_DEV_ID(NULL, "at91sam9rl-pwm", &pwm_clk),
- /* fake hclk clock */
- CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk),
- CLKDEV_CON_ID("pioA", &pioA_clk),
- CLKDEV_CON_ID("pioB", &pioB_clk),
- CLKDEV_CON_ID("pioC", &pioCDE_clk),
- CLKDEV_CON_ID("pioD", &pioCDE_clk),
- CLKDEV_CON_ID("pioE", &pioCDE_clk),
- /* more usart lookup table for DT entries */
- CLKDEV_CON_DEV_ID("usart", "ffffee00.serial", &mck),
- CLKDEV_CON_DEV_ID("usart", "fff8c000.serial", &usart0_clk),
- CLKDEV_CON_DEV_ID("usart", "fff90000.serial", &usart1_clk),
- CLKDEV_CON_DEV_ID("usart", "fff94000.serial", &usart2_clk),
- /* more tc lookup table for DT entries */
- CLKDEV_CON_DEV_ID("t0_clk", "fff7c000.timer", &tcb_clk),
- CLKDEV_CON_DEV_ID("hclk", "a00000.ohci", &ohci_clk),
- CLKDEV_CON_DEV_ID("spi_clk", "fffa4000.spi", &spi0_clk),
- CLKDEV_CON_DEV_ID("spi_clk", "fffa8000.spi", &spi1_clk),
- CLKDEV_CON_DEV_ID("mci_clk", "fff80000.mmc", &mmc0_clk),
- CLKDEV_CON_DEV_ID("mci_clk", "fff84000.mmc", &mmc1_clk),
- CLKDEV_CON_DEV_ID(NULL, "fff88000.i2c", &twi_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffff200.gpio", &pioA_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffff400.gpio", &pioB_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffff600.gpio", &pioCDE_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffff800.gpio", &pioCDE_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffffa00.gpio", &pioCDE_clk),
- CLKDEV_CON_DEV_ID(NULL, "fffb8000.pwm", &pwm_clk),
-};
-
-static struct clk_lookup usart_clocks_lookups[] = {
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.0", &mck),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.1", &usart0_clk),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.2", &usart1_clk),
- CLKDEV_CON_DEV_ID("usart", "atmel_usart.3", &usart2_clk),
-};
-
-/*
- * The four programmable clocks.
- * You must configure pin multiplexing to bring these signals out.
- */
-static struct clk pck0 = {
- .name = "pck0",
- .pmc_mask = AT91_PMC_PCK0,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 0,
-};
-static struct clk pck1 = {
- .name = "pck1",
- .pmc_mask = AT91_PMC_PCK1,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 1,
-};
-static struct clk pck2 = {
- .name = "pck2",
- .pmc_mask = AT91_PMC_PCK2,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 2,
-};
-static struct clk pck3 = {
- .name = "pck3",
- .pmc_mask = AT91_PMC_PCK3,
- .type = CLK_TYPE_PROGRAMMABLE,
- .id = 3,
-};
-
-static void __init at91sam9263_register_clocks(void)
-{
- int i;
-
- for (i = 0; i < ARRAY_SIZE(periph_clocks); i++)
- clk_register(periph_clocks[i]);
-
- clkdev_add_table(periph_clocks_lookups,
- ARRAY_SIZE(periph_clocks_lookups));
- clkdev_add_table(usart_clocks_lookups,
- ARRAY_SIZE(usart_clocks_lookups));
-
- clk_register(&pck0);
- clk_register(&pck1);
- clk_register(&pck2);
- clk_register(&pck3);
-}
-#else
-#define at91sam9263_register_clocks NULL
-#endif
-
-/* --------------------------------------------------------------------
- * GPIO
- * -------------------------------------------------------------------- */
-
-static struct at91_gpio_bank at91sam9263_gpio[] __initdata = {
- {
- .id = AT91SAM9263_ID_PIOA,
- .regbase = AT91SAM9263_BASE_PIOA,
- }, {
- .id = AT91SAM9263_ID_PIOB,
- .regbase = AT91SAM9263_BASE_PIOB,
- }, {
- .id = AT91SAM9263_ID_PIOCDE,
- .regbase = AT91SAM9263_BASE_PIOC,
- }, {
- .id = AT91SAM9263_ID_PIOCDE,
- .regbase = AT91SAM9263_BASE_PIOD,
- }, {
- .id = AT91SAM9263_ID_PIOCDE,
- .regbase = AT91SAM9263_BASE_PIOE,
- }
-};
/* --------------------------------------------------------------------
* AT91SAM9263 processor initialization
at91_init_sram(1, AT91SAM9263_SRAM1_BASE, AT91SAM9263_SRAM1_SIZE);
}
-static void __init at91sam9263_ioremap_registers(void)
-{
- at91_ioremap_ramc(0, AT91SAM9263_BASE_SDRAMC0, 512);
- at91_ioremap_ramc(1, AT91SAM9263_BASE_SDRAMC1, 512);
- at91sam926x_ioremap_pit(AT91SAM9263_BASE_PIT);
- at91sam9_ioremap_smc(0, AT91SAM9263_BASE_SMC0);
- at91sam9_ioremap_smc(1, AT91SAM9263_BASE_SMC1);
- at91_ioremap_matrix(AT91SAM9263_BASE_MATRIX);
- at91_pm_set_standby(at91sam9_sdram_standby);
-}
-
static void __init at91sam9263_initialize(void)
{
arm_pm_idle = at91sam9_idle;
at91_sysirq_mask_rtt(AT91SAM9263_BASE_RTT0);
at91_sysirq_mask_rtt(AT91SAM9263_BASE_RTT1);
-
- /* Register GPIO subsystem */
- at91_gpio_init(at91sam9263_gpio, 5);
-}
-
-static struct resource rstc_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_RSTC,
- .end = AT91SAM9263_BASE_RSTC + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91SAM9263_BASE_SDRAMC0,
- .end = AT91SAM9263_BASE_SDRAMC0 + SZ_512 - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device rstc_device = {
- .name = "at91-sam9260-reset",
- .resource = rstc_resources,
- .num_resources = ARRAY_SIZE(rstc_resources),
-};
-
-static struct resource shdwc_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_SHDWC,
- .end = AT91SAM9263_BASE_SHDWC + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct platform_device shdwc_device = {
- .name = "at91-poweroff",
- .resource = shdwc_resources,
- .num_resources = ARRAY_SIZE(shdwc_resources),
-};
-
-static void __init at91sam9263_register_devices(void)
-{
- platform_device_register(&rstc_device);
- platform_device_register(&shdwc_device);
-}
-
-/* --------------------------------------------------------------------
- * Interrupt initialization
- * -------------------------------------------------------------------- */
-
-/*
- * The default interrupt priority levels (0 = lowest, 7 = highest).
- */
-static unsigned int at91sam9263_default_irq_priority[NR_AIC_IRQS] __initdata = {
- 7, /* Advanced Interrupt Controller (FIQ) */
- 7, /* System Peripherals */
- 1, /* Parallel IO Controller A */
- 1, /* Parallel IO Controller B */
- 1, /* Parallel IO Controller C, D and E */
- 0,
- 0,
- 5, /* USART 0 */
- 5, /* USART 1 */
- 5, /* USART 2 */
- 0, /* Multimedia Card Interface 0 */
- 0, /* Multimedia Card Interface 1 */
- 3, /* CAN */
- 6, /* Two-Wire Interface */
- 5, /* Serial Peripheral Interface 0 */
- 5, /* Serial Peripheral Interface 1 */
- 4, /* Serial Synchronous Controller 0 */
- 4, /* Serial Synchronous Controller 1 */
- 5, /* AC97 Controller */
- 0, /* Timer Counter 0, 1 and 2 */
- 0, /* Pulse Width Modulation Controller */
- 3, /* Ethernet */
- 0,
- 0, /* 2D Graphic Engine */
- 2, /* USB Device Port */
- 0, /* Image Sensor Interface */
- 3, /* LDC Controller */
- 0, /* DMA Controller */
- 0,
- 2, /* USB Host port */
- 0, /* Advanced Interrupt Controller (IRQ0) */
- 0, /* Advanced Interrupt Controller (IRQ1) */
-};
-
-static void __init at91sam9263_init_time(void)
-{
- at91sam926x_pit_init(NR_IRQS_LEGACY + AT91_ID_SYS);
}
AT91_SOC_START(at91sam9263)
.map_io = at91sam9263_map_io,
- .default_irq_priority = at91sam9263_default_irq_priority,
- .extern_irq = (1 << AT91SAM9263_ID_IRQ0) | (1 << AT91SAM9263_ID_IRQ1),
- .ioremap_registers = at91sam9263_ioremap_registers,
- .register_clocks = at91sam9263_register_clocks,
- .register_devices = at91sam9263_register_devices,
.init = at91sam9263_initialize,
- .init_time = at91sam9263_init_time,
AT91_SOC_END
+++ /dev/null
-/*
- * arch/arm/mach-at91/at91sam9263_devices.c
- *
- * Copyright (C) 2007 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include <linux/dma-mapping.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/i2c-gpio.h>
-
-#include <linux/fb.h>
-#include <video/atmel_lcdc.h>
-
-#include <mach/at91sam9263.h>
-#include <mach/at91sam9263_matrix.h>
-#include <mach/at91_matrix.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/hardware.h>
-
-#include "board.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-/* --------------------------------------------------------------------
- * USB Host
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
-static u64 ohci_dmamask = DMA_BIT_MASK(32);
-static struct at91_usbh_data usbh_data;
-
-static struct resource usbh_resources[] = {
- [0] = {
- .start = AT91SAM9263_UHP_BASE,
- .end = AT91SAM9263_UHP_BASE + SZ_1M - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_UHP,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_UHP,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91_usbh_device = {
- .name = "at91_ohci",
- .id = -1,
- .dev = {
- .dma_mask = &ohci_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &usbh_data,
- },
- .resource = usbh_resources,
- .num_resources = ARRAY_SIZE(usbh_resources),
-};
-
-void __init at91_add_device_usbh(struct at91_usbh_data *data)
-{
- int i;
-
- if (!data)
- return;
-
- /* Enable VBus control for UHP ports */
- for (i = 0; i < data->ports; i++) {
- if (gpio_is_valid(data->vbus_pin[i]))
- at91_set_gpio_output(data->vbus_pin[i],
- data->vbus_pin_active_low[i]);
- }
-
- /* Enable overcurrent notification */
- for (i = 0; i < data->ports; i++) {
- if (gpio_is_valid(data->overcurrent_pin[i]))
- at91_set_gpio_input(data->overcurrent_pin[i], 1);
- }
-
- usbh_data = *data;
- platform_device_register(&at91_usbh_device);
-}
-#else
-void __init at91_add_device_usbh(struct at91_usbh_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * USB Device (Gadget)
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_USB_AT91) || defined(CONFIG_USB_AT91_MODULE)
-static struct at91_udc_data udc_data;
-
-static struct resource udc_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_UDP,
- .end = AT91SAM9263_BASE_UDP + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_UDP,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_UDP,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91_udc_device = {
- .name = "at91_udc",
- .id = -1,
- .dev = {
- .platform_data = &udc_data,
- },
- .resource = udc_resources,
- .num_resources = ARRAY_SIZE(udc_resources),
-};
-
-void __init at91_add_device_udc(struct at91_udc_data *data)
-{
- if (!data)
- return;
-
- if (gpio_is_valid(data->vbus_pin)) {
- at91_set_gpio_input(data->vbus_pin, 0);
- at91_set_deglitch(data->vbus_pin, 1);
- }
-
- /* Pullup pin is handled internally by USB device peripheral */
-
- udc_data = *data;
- platform_device_register(&at91_udc_device);
-}
-#else
-void __init at91_add_device_udc(struct at91_udc_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Ethernet
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MACB) || defined(CONFIG_MACB_MODULE)
-static u64 eth_dmamask = DMA_BIT_MASK(32);
-static struct macb_platform_data eth_data;
-
-static struct resource eth_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_EMAC,
- .end = AT91SAM9263_BASE_EMAC + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_EMAC,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_EMAC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_eth_device = {
- .name = "macb",
- .id = -1,
- .dev = {
- .dma_mask = ð_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = ð_data,
- },
- .resource = eth_resources,
- .num_resources = ARRAY_SIZE(eth_resources),
-};
-
-void __init at91_add_device_eth(struct macb_platform_data *data)
-{
- if (!data)
- return;
-
- if (gpio_is_valid(data->phy_irq_pin)) {
- at91_set_gpio_input(data->phy_irq_pin, 0);
- at91_set_deglitch(data->phy_irq_pin, 1);
- }
-
- /* Pins used for MII and RMII */
- at91_set_A_periph(AT91_PIN_PE21, 0); /* ETXCK_EREFCK */
- at91_set_B_periph(AT91_PIN_PC25, 0); /* ERXDV */
- at91_set_A_periph(AT91_PIN_PE25, 0); /* ERX0 */
- at91_set_A_periph(AT91_PIN_PE26, 0); /* ERX1 */
- at91_set_A_periph(AT91_PIN_PE27, 0); /* ERXER */
- at91_set_A_periph(AT91_PIN_PE28, 0); /* ETXEN */
- at91_set_A_periph(AT91_PIN_PE23, 0); /* ETX0 */
- at91_set_A_periph(AT91_PIN_PE24, 0); /* ETX1 */
- at91_set_A_periph(AT91_PIN_PE30, 0); /* EMDIO */
- at91_set_A_periph(AT91_PIN_PE29, 0); /* EMDC */
-
- if (!data->is_rmii) {
- at91_set_A_periph(AT91_PIN_PE22, 0); /* ECRS */
- at91_set_B_periph(AT91_PIN_PC26, 0); /* ECOL */
- at91_set_B_periph(AT91_PIN_PC22, 0); /* ERX2 */
- at91_set_B_periph(AT91_PIN_PC23, 0); /* ERX3 */
- at91_set_B_periph(AT91_PIN_PC27, 0); /* ERXCK */
- at91_set_B_periph(AT91_PIN_PC20, 0); /* ETX2 */
- at91_set_B_periph(AT91_PIN_PC21, 0); /* ETX3 */
- at91_set_B_periph(AT91_PIN_PC24, 0); /* ETXER */
- }
-
- eth_data = *data;
- platform_device_register(&at91sam9263_eth_device);
-}
-#else
-void __init at91_add_device_eth(struct macb_platform_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * MMC / SD
- * -------------------------------------------------------------------- */
-
-#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
-static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct mci_platform_data mmc0_data, mmc1_data;
-
-static struct resource mmc0_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_MCI0,
- .end = AT91SAM9263_BASE_MCI0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI0,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_mmc0_device = {
- .name = "atmel_mci",
- .id = 0,
- .dev = {
- .dma_mask = &mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &mmc0_data,
- },
- .resource = mmc0_resources,
- .num_resources = ARRAY_SIZE(mmc0_resources),
-};
-
-static struct resource mmc1_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_MCI1,
- .end = AT91SAM9263_BASE_MCI1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI1,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_MCI1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_mmc1_device = {
- .name = "atmel_mci",
- .id = 1,
- .dev = {
- .dma_mask = &mmc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &mmc1_data,
- },
- .resource = mmc1_resources,
- .num_resources = ARRAY_SIZE(mmc1_resources),
-};
-
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
-{
- unsigned int i;
- unsigned int slot_count = 0;
-
- if (!data)
- return;
-
- for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
-
- if (!data->slot[i].bus_width)
- continue;
-
- /* input/irq */
- if (gpio_is_valid(data->slot[i].detect_pin)) {
- at91_set_gpio_input(data->slot[i].detect_pin,
- 1);
- at91_set_deglitch(data->slot[i].detect_pin,
- 1);
- }
- if (gpio_is_valid(data->slot[i].wp_pin))
- at91_set_gpio_input(data->slot[i].wp_pin, 1);
-
- if (mmc_id == 0) { /* MCI0 */
- switch (i) {
- case 0: /* slot A */
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA1, 1);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA0, 1);
- if (data->slot[i].bus_width == 4) {
- at91_set_A_periph(AT91_PIN_PA3, 1);
- at91_set_A_periph(AT91_PIN_PA4, 1);
- at91_set_A_periph(AT91_PIN_PA5, 1);
- }
- slot_count++;
- break;
- case 1: /* slot B */
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA16, 1);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA17, 1);
- if (data->slot[i].bus_width == 4) {
- at91_set_A_periph(AT91_PIN_PA18, 1);
- at91_set_A_periph(AT91_PIN_PA19, 1);
- at91_set_A_periph(AT91_PIN_PA20, 1);
- }
- slot_count++;
- break;
- default:
- printk(KERN_ERR
- "AT91: SD/MMC slot %d not available\n", i);
- break;
- }
- if (slot_count) {
- /* CLK */
- at91_set_A_periph(AT91_PIN_PA12, 0);
-
- mmc0_data = *data;
- platform_device_register(&at91sam9263_mmc0_device);
- }
- } else if (mmc_id == 1) { /* MCI1 */
- switch (i) {
- case 0: /* slot A */
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA7, 1);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA8, 1);
- if (data->slot[i].bus_width == 4) {
- at91_set_A_periph(AT91_PIN_PA9, 1);
- at91_set_A_periph(AT91_PIN_PA10, 1);
- at91_set_A_periph(AT91_PIN_PA11, 1);
- }
- slot_count++;
- break;
- case 1: /* slot B */
- /* CMD */
- at91_set_A_periph(AT91_PIN_PA21, 1);
- /* DAT0, maybe DAT1..DAT3 */
- at91_set_A_periph(AT91_PIN_PA22, 1);
- if (data->slot[i].bus_width == 4) {
- at91_set_A_periph(AT91_PIN_PA23, 1);
- at91_set_A_periph(AT91_PIN_PA24, 1);
- at91_set_A_periph(AT91_PIN_PA25, 1);
- }
- slot_count++;
- break;
- default:
- printk(KERN_ERR
- "AT91: SD/MMC slot %d not available\n", i);
- break;
- }
- if (slot_count) {
- /* CLK */
- at91_set_A_periph(AT91_PIN_PA6, 0);
-
- mmc1_data = *data;
- platform_device_register(&at91sam9263_mmc1_device);
- }
- }
- }
-}
-#else
-void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- * Compact Flash (PCMCIA or IDE)
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_PATA_AT91) || defined(CONFIG_PATA_AT91_MODULE) || \
- defined(CONFIG_AT91_CF) || defined(CONFIG_AT91_CF_MODULE)
-
-static struct at91_cf_data cf0_data;
-
-static struct resource cf0_resources[] = {
- [0] = {
- .start = AT91_CHIPSELECT_4,
- .end = AT91_CHIPSELECT_4 + SZ_256M - 1,
- .flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
- }
-};
-
-static struct platform_device cf0_device = {
- .id = 0,
- .dev = {
- .platform_data = &cf0_data,
- },
- .resource = cf0_resources,
- .num_resources = ARRAY_SIZE(cf0_resources),
-};
-
-static struct at91_cf_data cf1_data;
-
-static struct resource cf1_resources[] = {
- [0] = {
- .start = AT91_CHIPSELECT_5,
- .end = AT91_CHIPSELECT_5 + SZ_256M - 1,
- .flags = IORESOURCE_MEM | IORESOURCE_MEM_8AND16BIT,
- }
-};
-
-static struct platform_device cf1_device = {
- .id = 1,
- .dev = {
- .platform_data = &cf1_data,
- },
- .resource = cf1_resources,
- .num_resources = ARRAY_SIZE(cf1_resources),
-};
-
-void __init at91_add_device_cf(struct at91_cf_data *data)
-{
- unsigned long ebi0_csa;
- struct platform_device *pdev;
-
- if (!data)
- return;
-
- /*
- * assign CS4 or CS5 to SMC with Compact Flash logic support,
- * we assume SMC timings are configured by board code,
- * except True IDE where timings are controlled by driver
- */
- ebi0_csa = at91_matrix_read(AT91_MATRIX_EBI0CSA);
- switch (data->chipselect) {
- case 4:
- at91_set_A_periph(AT91_PIN_PD6, 0); /* EBI0_NCS4/CFCS0 */
- ebi0_csa |= AT91_MATRIX_EBI0_CS4A_SMC_CF1;
- cf0_data = *data;
- pdev = &cf0_device;
- break;
- case 5:
- at91_set_A_periph(AT91_PIN_PD7, 0); /* EBI0_NCS5/CFCS1 */
- ebi0_csa |= AT91_MATRIX_EBI0_CS5A_SMC_CF2;
- cf1_data = *data;
- pdev = &cf1_device;
- break;
- default:
- printk(KERN_ERR "AT91 CF: bad chip-select requested (%u)\n",
- data->chipselect);
- return;
- }
- at91_matrix_write(AT91_MATRIX_EBI0CSA, ebi0_csa);
-
- if (gpio_is_valid(data->det_pin)) {
- at91_set_gpio_input(data->det_pin, 1);
- at91_set_deglitch(data->det_pin, 1);
- }
-
- if (gpio_is_valid(data->irq_pin)) {
- at91_set_gpio_input(data->irq_pin, 1);
- at91_set_deglitch(data->irq_pin, 1);
- }
-
- if (gpio_is_valid(data->vcc_pin))
- /* initially off */
- at91_set_gpio_output(data->vcc_pin, 0);
-
- /* enable EBI controlled pins */
- at91_set_A_periph(AT91_PIN_PD5, 1); /* NWAIT */
- at91_set_A_periph(AT91_PIN_PD8, 0); /* CFCE1 */
- at91_set_A_periph(AT91_PIN_PD9, 0); /* CFCE2 */
- at91_set_A_periph(AT91_PIN_PD14, 0); /* CFNRW */
-
- pdev->name = (data->flags & AT91_CF_TRUE_IDE) ? "pata_at91" : "at91_cf";
- platform_device_register(pdev);
-}
-#else
-void __init at91_add_device_cf(struct at91_cf_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- * NAND / SmartMedia
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
-static struct atmel_nand_data nand_data;
-
-#define NAND_BASE AT91_CHIPSELECT_3
-
-static struct resource nand_resources[] = {
- [0] = {
- .start = NAND_BASE,
- .end = NAND_BASE + SZ_256M - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = AT91SAM9263_BASE_ECC0,
- .end = AT91SAM9263_BASE_ECC0 + SZ_512 - 1,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct platform_device at91sam9263_nand_device = {
- .name = "atmel_nand",
- .id = -1,
- .dev = {
- .platform_data = &nand_data,
- },
- .resource = nand_resources,
- .num_resources = ARRAY_SIZE(nand_resources),
-};
-
-void __init at91_add_device_nand(struct atmel_nand_data *data)
-{
- unsigned long csa;
-
- if (!data)
- return;
-
- csa = at91_matrix_read(AT91_MATRIX_EBI0CSA);
- at91_matrix_write(AT91_MATRIX_EBI0CSA, csa | AT91_MATRIX_EBI0_CS3A_SMC_SMARTMEDIA);
-
- /* enable pin */
- if (gpio_is_valid(data->enable_pin))
- at91_set_gpio_output(data->enable_pin, 1);
-
- /* ready/busy pin */
- if (gpio_is_valid(data->rdy_pin))
- at91_set_gpio_input(data->rdy_pin, 1);
-
- /* card detect pin */
- if (gpio_is_valid(data->det_pin))
- at91_set_gpio_input(data->det_pin, 1);
-
- nand_data = *data;
- platform_device_register(&at91sam9263_nand_device);
-}
-#else
-void __init at91_add_device_nand(struct atmel_nand_data *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * TWI (i2c)
- * -------------------------------------------------------------------- */
-
-/*
- * Prefer the GPIO code since the TWI controller isn't robust
- * (gets overruns and underruns under load) and can only issue
- * repeated STARTs in one scenario (the driver doesn't yet handle them).
- */
-#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
-
-static struct i2c_gpio_platform_data pdata = {
- .sda_pin = AT91_PIN_PB4,
- .sda_is_open_drain = 1,
- .scl_pin = AT91_PIN_PB5,
- .scl_is_open_drain = 1,
- .udelay = 2, /* ~100 kHz */
-};
-
-static struct platform_device at91sam9263_twi_device = {
- .name = "i2c-gpio",
- .id = 0,
- .dev.platform_data = &pdata,
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
- at91_set_GPIO_periph(AT91_PIN_PB4, 1); /* TWD (SDA) */
- at91_set_multi_drive(AT91_PIN_PB4, 1);
-
- at91_set_GPIO_periph(AT91_PIN_PB5, 1); /* TWCK (SCL) */
- at91_set_multi_drive(AT91_PIN_PB5, 1);
-
- i2c_register_board_info(0, devices, nr_devices);
- platform_device_register(&at91sam9263_twi_device);
-}
-
-#elif defined(CONFIG_I2C_AT91) || defined(CONFIG_I2C_AT91_MODULE)
-
-static struct resource twi_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_TWI,
- .end = AT91SAM9263_BASE_TWI + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_TWI,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_TWI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_twi_device = {
- .name = "i2c-at91sam9260",
- .id = 0,
- .resource = twi_resources,
- .num_resources = ARRAY_SIZE(twi_resources),
-};
-
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices)
-{
- /* pins used for TWI interface */
- at91_set_A_periph(AT91_PIN_PB4, 0); /* TWD */
- at91_set_multi_drive(AT91_PIN_PB4, 1);
-
- at91_set_A_periph(AT91_PIN_PB5, 0); /* TWCK */
- at91_set_multi_drive(AT91_PIN_PB5, 1);
-
- i2c_register_board_info(0, devices, nr_devices);
- platform_device_register(&at91sam9263_twi_device);
-}
-#else
-void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * SPI
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SPI_ATMEL) || defined(CONFIG_SPI_ATMEL_MODULE)
-static u64 spi_dmamask = DMA_BIT_MASK(32);
-
-static struct resource spi0_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_SPI0,
- .end = AT91SAM9263_BASE_SPI0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI0,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_spi0_device = {
- .name = "atmel_spi",
- .id = 0,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = spi0_resources,
- .num_resources = ARRAY_SIZE(spi0_resources),
-};
-
-static const unsigned spi0_standard_cs[4] = { AT91_PIN_PA5, AT91_PIN_PA3, AT91_PIN_PA4, AT91_PIN_PB11 };
-
-static struct resource spi1_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_SPI1,
- .end = AT91SAM9263_BASE_SPI1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI1,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SPI1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_spi1_device = {
- .name = "atmel_spi",
- .id = 1,
- .dev = {
- .dma_mask = &spi_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = spi1_resources,
- .num_resources = ARRAY_SIZE(spi1_resources),
-};
-
-static const unsigned spi1_standard_cs[4] = { AT91_PIN_PB15, AT91_PIN_PB16, AT91_PIN_PB17, AT91_PIN_PB18 };
-
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
-{
- int i;
- unsigned long cs_pin;
- short enable_spi0 = 0;
- short enable_spi1 = 0;
-
- /* Choose SPI chip-selects */
- for (i = 0; i < nr_devices; i++) {
- if (devices[i].controller_data)
- cs_pin = (unsigned long) devices[i].controller_data;
- else if (devices[i].bus_num == 0)
- cs_pin = spi0_standard_cs[devices[i].chip_select];
- else
- cs_pin = spi1_standard_cs[devices[i].chip_select];
-
- if (!gpio_is_valid(cs_pin))
- continue;
-
- if (devices[i].bus_num == 0)
- enable_spi0 = 1;
- else
- enable_spi1 = 1;
-
- /* enable chip-select pin */
- at91_set_gpio_output(cs_pin, 1);
-
- /* pass chip-select pin to driver */
- devices[i].controller_data = (void *) cs_pin;
- }
-
- spi_register_board_info(devices, nr_devices);
-
- /* Configure SPI bus(es) */
- if (enable_spi0) {
- at91_set_B_periph(AT91_PIN_PA0, 0); /* SPI0_MISO */
- at91_set_B_periph(AT91_PIN_PA1, 0); /* SPI0_MOSI */
- at91_set_B_periph(AT91_PIN_PA2, 0); /* SPI0_SPCK */
-
- platform_device_register(&at91sam9263_spi0_device);
- }
- if (enable_spi1) {
- at91_set_A_periph(AT91_PIN_PB12, 0); /* SPI1_MISO */
- at91_set_A_periph(AT91_PIN_PB13, 0); /* SPI1_MOSI */
- at91_set_A_periph(AT91_PIN_PB14, 0); /* SPI1_SPCK */
-
- platform_device_register(&at91sam9263_spi1_device);
- }
-}
-#else
-void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * AC97
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
-static u64 ac97_dmamask = DMA_BIT_MASK(32);
-static struct ac97c_platform_data ac97_data;
-
-static struct resource ac97_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_AC97C,
- .end = AT91SAM9263_BASE_AC97C + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_AC97C,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_AC97C,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_ac97_device = {
- .name = "atmel_ac97c",
- .id = 0,
- .dev = {
- .dma_mask = &ac97_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &ac97_data,
- },
- .resource = ac97_resources,
- .num_resources = ARRAY_SIZE(ac97_resources),
-};
-
-void __init at91_add_device_ac97(struct ac97c_platform_data *data)
-{
- if (!data)
- return;
-
- at91_set_A_periph(AT91_PIN_PB0, 0); /* AC97FS */
- at91_set_A_periph(AT91_PIN_PB1, 0); /* AC97CK */
- at91_set_A_periph(AT91_PIN_PB2, 0); /* AC97TX */
- at91_set_A_periph(AT91_PIN_PB3, 0); /* AC97RX */
-
- /* reset */
- if (gpio_is_valid(data->reset_pin))
- at91_set_gpio_output(data->reset_pin, 0);
-
- ac97_data = *data;
- platform_device_register(&at91sam9263_ac97_device);
-}
-#else
-void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- * CAN Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_CAN_AT91) || defined(CONFIG_CAN_AT91_MODULE)
-static struct resource can_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_CAN,
- .end = AT91SAM9263_BASE_CAN + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_CAN,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_CAN,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_can_device = {
- .name = "at91_can",
- .id = -1,
- .resource = can_resources,
- .num_resources = ARRAY_SIZE(can_resources),
-};
-
-void __init at91_add_device_can(struct at91_can_data *data)
-{
- at91_set_A_periph(AT91_PIN_PA13, 0); /* CANTX */
- at91_set_A_periph(AT91_PIN_PA14, 0); /* CANRX */
- at91sam9263_can_device.dev.platform_data = data;
-
- platform_device_register(&at91sam9263_can_device);
-}
-#else
-void __init at91_add_device_can(struct at91_can_data *data) {}
-#endif
-
-/* --------------------------------------------------------------------
- * LCD Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static u64 lcdc_dmamask = DMA_BIT_MASK(32);
-static struct atmel_lcdfb_pdata lcdc_data;
-
-static struct resource lcdc_resources[] = {
- [0] = {
- .start = AT91SAM9263_LCDC_BASE,
- .end = AT91SAM9263_LCDC_BASE + SZ_4K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_LCDC,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_LCDC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91_lcdc_device = {
- .name = "at91sam9263-lcdfb",
- .id = 0,
- .dev = {
- .dma_mask = &lcdc_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &lcdc_data,
- },
- .resource = lcdc_resources,
- .num_resources = ARRAY_SIZE(lcdc_resources),
-};
-
-void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data)
-{
- if (!data)
- return;
-
- at91_set_A_periph(AT91_PIN_PC1, 0); /* LCDHSYNC */
- at91_set_A_periph(AT91_PIN_PC2, 0); /* LCDDOTCK */
- at91_set_A_periph(AT91_PIN_PC3, 0); /* LCDDEN */
- at91_set_B_periph(AT91_PIN_PB9, 0); /* LCDCC */
- at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDD2 */
- at91_set_A_periph(AT91_PIN_PC7, 0); /* LCDD3 */
- at91_set_A_periph(AT91_PIN_PC8, 0); /* LCDD4 */
- at91_set_A_periph(AT91_PIN_PC9, 0); /* LCDD5 */
- at91_set_A_periph(AT91_PIN_PC10, 0); /* LCDD6 */
- at91_set_A_periph(AT91_PIN_PC11, 0); /* LCDD7 */
- at91_set_A_periph(AT91_PIN_PC14, 0); /* LCDD10 */
- at91_set_A_periph(AT91_PIN_PC15, 0); /* LCDD11 */
- at91_set_A_periph(AT91_PIN_PC16, 0); /* LCDD12 */
- at91_set_B_periph(AT91_PIN_PC12, 0); /* LCDD13 */
- at91_set_A_periph(AT91_PIN_PC18, 0); /* LCDD14 */
- at91_set_A_periph(AT91_PIN_PC19, 0); /* LCDD15 */
- at91_set_A_periph(AT91_PIN_PC22, 0); /* LCDD18 */
- at91_set_A_periph(AT91_PIN_PC23, 0); /* LCDD19 */
- at91_set_A_periph(AT91_PIN_PC24, 0); /* LCDD20 */
- at91_set_B_periph(AT91_PIN_PC17, 0); /* LCDD21 */
- at91_set_A_periph(AT91_PIN_PC26, 0); /* LCDD22 */
- at91_set_A_periph(AT91_PIN_PC27, 0); /* LCDD23 */
-
- lcdc_data = *data;
- platform_device_register(&at91_lcdc_device);
-}
-#else
-void __init at91_add_device_lcdc(struct atmel_lcdfb_pdata *data) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Image Sensor Interface
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_VIDEO_AT91_ISI) || defined(CONFIG_VIDEO_AT91_ISI_MODULE)
-
-struct resource isi_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_ISI,
- .end = AT91SAM9263_BASE_ISI + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_ISI,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_ISI,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_isi_device = {
- .name = "at91_isi",
- .id = -1,
- .resource = isi_resources,
- .num_resources = ARRAY_SIZE(isi_resources),
-};
-
-void __init at91_add_device_isi(struct isi_platform_data *data,
- bool use_pck_as_mck)
-{
- at91_set_A_periph(AT91_PIN_PE0, 0); /* ISI_D0 */
- at91_set_A_periph(AT91_PIN_PE1, 0); /* ISI_D1 */
- at91_set_A_periph(AT91_PIN_PE2, 0); /* ISI_D2 */
- at91_set_A_periph(AT91_PIN_PE3, 0); /* ISI_D3 */
- at91_set_A_periph(AT91_PIN_PE4, 0); /* ISI_D4 */
- at91_set_A_periph(AT91_PIN_PE5, 0); /* ISI_D5 */
- at91_set_A_periph(AT91_PIN_PE6, 0); /* ISI_D6 */
- at91_set_A_periph(AT91_PIN_PE7, 0); /* ISI_D7 */
- at91_set_A_periph(AT91_PIN_PE8, 0); /* ISI_PCK */
- at91_set_A_periph(AT91_PIN_PE9, 0); /* ISI_HSYNC */
- at91_set_A_periph(AT91_PIN_PE10, 0); /* ISI_VSYNC */
- at91_set_B_periph(AT91_PIN_PE12, 0); /* ISI_PD8 */
- at91_set_B_periph(AT91_PIN_PE13, 0); /* ISI_PD9 */
- at91_set_B_periph(AT91_PIN_PE14, 0); /* ISI_PD10 */
- at91_set_B_periph(AT91_PIN_PE15, 0); /* ISI_PD11 */
-
- if (use_pck_as_mck) {
- at91_set_B_periph(AT91_PIN_PE11, 0); /* ISI_MCK (PCK3) */
-
- /* TODO: register the PCK for ISI_MCK and set its parent */
- }
-}
-#else
-void __init at91_add_device_isi(struct isi_platform_data *data,
- bool use_pck_as_mck) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * Timer/Counter block
- * -------------------------------------------------------------------- */
-
-#ifdef CONFIG_ATMEL_TCLIB
-
-static struct resource tcb_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_TCB0,
- .end = AT91SAM9263_BASE_TCB0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_TCB,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_TCB,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_tcb_device = {
- .name = "atmel_tcb",
- .id = 0,
- .resource = tcb_resources,
- .num_resources = ARRAY_SIZE(tcb_resources),
-};
-
-#if defined(CONFIG_OF)
-static struct of_device_id tcb_ids[] = {
- { .compatible = "atmel,at91rm9200-tcb" },
- { /*sentinel*/ }
-};
-#endif
-
-static void __init at91_add_device_tc(void)
-{
-#if defined(CONFIG_OF)
- struct device_node *np;
-
- np = of_find_matching_node(NULL, tcb_ids);
- if (np) {
- of_node_put(np);
- return;
- }
-#endif
-
- platform_device_register(&at91sam9263_tcb_device);
-}
-#else
-static void __init at91_add_device_tc(void) { }
-#endif
-
-
-/* --------------------------------------------------------------------
- * RTT
- * -------------------------------------------------------------------- */
-
-static struct resource rtt0_resources[] = {
- {
- .start = AT91SAM9263_BASE_RTT0,
- .end = AT91SAM9263_BASE_RTT0 + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .flags = IORESOURCE_MEM,
- }, {
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static struct platform_device at91sam9263_rtt0_device = {
- .name = "at91_rtt",
- .id = 0,
- .resource = rtt0_resources,
-};
-
-static struct resource rtt1_resources[] = {
- {
- .start = AT91SAM9263_BASE_RTT1,
- .end = AT91SAM9263_BASE_RTT1 + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- }, {
- .flags = IORESOURCE_MEM,
- }, {
- .flags = IORESOURCE_IRQ,
- }
-};
-
-static struct platform_device at91sam9263_rtt1_device = {
- .name = "at91_rtt",
- .id = 1,
- .resource = rtt1_resources,
-};
-
-#if IS_ENABLED(CONFIG_RTC_DRV_AT91SAM9)
-static void __init at91_add_device_rtt_rtc(void)
-{
- struct platform_device *pdev;
- struct resource *r;
-
- switch (CONFIG_RTC_DRV_AT91SAM9_RTT) {
- case 0:
- /*
- * The second resource is needed only for the chosen RTT:
- * GPBR will serve as the storage for RTC time offset
- */
- at91sam9263_rtt0_device.num_resources = 3;
- at91sam9263_rtt1_device.num_resources = 1;
- pdev = &at91sam9263_rtt0_device;
- r = rtt0_resources;
- break;
- case 1:
- at91sam9263_rtt0_device.num_resources = 1;
- at91sam9263_rtt1_device.num_resources = 3;
- pdev = &at91sam9263_rtt1_device;
- r = rtt1_resources;
- break;
- default:
- pr_err("at91sam9263: only supports 2 RTT (%d)\n",
- CONFIG_RTC_DRV_AT91SAM9_RTT);
- return;
- }
-
- pdev->name = "rtc-at91sam9";
- r[1].start = AT91SAM9263_BASE_GPBR + 4 * CONFIG_RTC_DRV_AT91SAM9_GPBR;
- r[1].end = r[1].start + 3;
- r[2].start = NR_IRQS_LEGACY + AT91_ID_SYS;
- r[2].end = NR_IRQS_LEGACY + AT91_ID_SYS;
-}
-#else
-static void __init at91_add_device_rtt_rtc(void)
-{
- /* Only one resource is needed: RTT not used as RTC */
- at91sam9263_rtt0_device.num_resources = 1;
- at91sam9263_rtt1_device.num_resources = 1;
-}
-#endif
-
-static void __init at91_add_device_rtt(void)
-{
- at91_add_device_rtt_rtc();
- platform_device_register(&at91sam9263_rtt0_device);
- platform_device_register(&at91sam9263_rtt1_device);
-}
-
-
-/* --------------------------------------------------------------------
- * Watchdog
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_AT91SAM9X_WATCHDOG) || defined(CONFIG_AT91SAM9X_WATCHDOG_MODULE)
-static struct resource wdt_resources[] = {
- {
- .start = AT91SAM9263_BASE_WDT,
- .end = AT91SAM9263_BASE_WDT + SZ_16 - 1,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct platform_device at91sam9263_wdt_device = {
- .name = "at91_wdt",
- .id = -1,
- .resource = wdt_resources,
- .num_resources = ARRAY_SIZE(wdt_resources),
-};
-
-static void __init at91_add_device_watchdog(void)
-{
- platform_device_register(&at91sam9263_wdt_device);
-}
-#else
-static void __init at91_add_device_watchdog(void) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * PWM
- * --------------------------------------------------------------------*/
-
-#if IS_ENABLED(CONFIG_PWM_ATMEL)
-static struct resource pwm_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_PWMC,
- .end = AT91SAM9263_BASE_PWMC + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_PWMC,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_PWMC,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_pwm0_device = {
- .name = "at91sam9rl-pwm",
- .id = -1,
- .resource = pwm_resources,
- .num_resources = ARRAY_SIZE(pwm_resources),
-};
-
-void __init at91_add_device_pwm(u32 mask)
-{
- if (mask & (1 << AT91_PWM0))
- at91_set_B_periph(AT91_PIN_PB7, 1); /* enable PWM0 */
-
- if (mask & (1 << AT91_PWM1))
- at91_set_B_periph(AT91_PIN_PB8, 1); /* enable PWM1 */
-
- if (mask & (1 << AT91_PWM2))
- at91_set_B_periph(AT91_PIN_PC29, 1); /* enable PWM2 */
-
- if (mask & (1 << AT91_PWM3))
- at91_set_B_periph(AT91_PIN_PB29, 1); /* enable PWM3 */
-
- platform_device_register(&at91sam9263_pwm0_device);
-}
-#else
-void __init at91_add_device_pwm(u32 mask) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * SSC -- Synchronous Serial Controller
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_ATMEL_SSC) || defined(CONFIG_ATMEL_SSC_MODULE)
-static u64 ssc0_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc0_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_SSC0,
- .end = AT91SAM9263_BASE_SSC0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC0,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_ssc0_device = {
- .name = "at91rm9200_ssc",
- .id = 0,
- .dev = {
- .dma_mask = &ssc0_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = ssc0_resources,
- .num_resources = ARRAY_SIZE(ssc0_resources),
-};
-
-static inline void configure_ssc0_pins(unsigned pins)
-{
- if (pins & ATMEL_SSC_TF)
- at91_set_B_periph(AT91_PIN_PB0, 1);
- if (pins & ATMEL_SSC_TK)
- at91_set_B_periph(AT91_PIN_PB1, 1);
- if (pins & ATMEL_SSC_TD)
- at91_set_B_periph(AT91_PIN_PB2, 1);
- if (pins & ATMEL_SSC_RD)
- at91_set_B_periph(AT91_PIN_PB3, 1);
- if (pins & ATMEL_SSC_RK)
- at91_set_B_periph(AT91_PIN_PB4, 1);
- if (pins & ATMEL_SSC_RF)
- at91_set_B_periph(AT91_PIN_PB5, 1);
-}
-
-static u64 ssc1_dmamask = DMA_BIT_MASK(32);
-
-static struct resource ssc1_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_SSC1,
- .end = AT91SAM9263_BASE_SSC1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC1,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_SSC1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct platform_device at91sam9263_ssc1_device = {
- .name = "at91rm9200_ssc",
- .id = 1,
- .dev = {
- .dma_mask = &ssc1_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- },
- .resource = ssc1_resources,
- .num_resources = ARRAY_SIZE(ssc1_resources),
-};
-
-static inline void configure_ssc1_pins(unsigned pins)
-{
- if (pins & ATMEL_SSC_TF)
- at91_set_A_periph(AT91_PIN_PB6, 1);
- if (pins & ATMEL_SSC_TK)
- at91_set_A_periph(AT91_PIN_PB7, 1);
- if (pins & ATMEL_SSC_TD)
- at91_set_A_periph(AT91_PIN_PB8, 1);
- if (pins & ATMEL_SSC_RD)
- at91_set_A_periph(AT91_PIN_PB9, 1);
- if (pins & ATMEL_SSC_RK)
- at91_set_A_periph(AT91_PIN_PB10, 1);
- if (pins & ATMEL_SSC_RF)
- at91_set_A_periph(AT91_PIN_PB11, 1);
-}
-
-/*
- * SSC controllers are accessed through library code, instead of any
- * kind of all-singing/all-dancing driver. For example one could be
- * used by a particular I2S audio codec's driver, while another one
- * on the same system might be used by a custom data capture driver.
- */
-void __init at91_add_device_ssc(unsigned id, unsigned pins)
-{
- struct platform_device *pdev;
-
- /*
- * NOTE: caller is responsible for passing information matching
- * "pins" to whatever will be using each particular controller.
- */
- switch (id) {
- case AT91SAM9263_ID_SSC0:
- pdev = &at91sam9263_ssc0_device;
- configure_ssc0_pins(pins);
- break;
- case AT91SAM9263_ID_SSC1:
- pdev = &at91sam9263_ssc1_device;
- configure_ssc1_pins(pins);
- break;
- default:
- return;
- }
-
- platform_device_register(pdev);
-}
-
-#else
-void __init at91_add_device_ssc(unsigned id, unsigned pins) {}
-#endif
-
-
-/* --------------------------------------------------------------------
- * UART
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_SERIAL_ATMEL)
-
-static struct resource dbgu_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_DBGU,
- .end = AT91SAM9263_BASE_DBGU + SZ_512 - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91_ID_SYS,
- .end = NR_IRQS_LEGACY + AT91_ID_SYS,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data dbgu_data = {
- .use_dma_tx = 0,
- .use_dma_rx = 0, /* DBGU not capable of receive DMA */
-};
-
-static u64 dbgu_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_dbgu_device = {
- .name = "atmel_usart",
- .id = 0,
- .dev = {
- .dma_mask = &dbgu_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &dbgu_data,
- },
- .resource = dbgu_resources,
- .num_resources = ARRAY_SIZE(dbgu_resources),
-};
-
-static inline void configure_dbgu_pins(void)
-{
- at91_set_A_periph(AT91_PIN_PC30, 0); /* DRXD */
- at91_set_A_periph(AT91_PIN_PC31, 1); /* DTXD */
-}
-
-static struct resource uart0_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_US0,
- .end = AT91SAM9263_BASE_US0 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_US0,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_US0,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart0_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart0_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_uart0_device = {
- .name = "atmel_usart",
- .id = 1,
- .dev = {
- .dma_mask = &uart0_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart0_data,
- },
- .resource = uart0_resources,
- .num_resources = ARRAY_SIZE(uart0_resources),
-};
-
-static inline void configure_usart0_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PA26, 1); /* TXD0 */
- at91_set_A_periph(AT91_PIN_PA27, 0); /* RXD0 */
-
- if (pins & ATMEL_UART_RTS)
- at91_set_A_periph(AT91_PIN_PA28, 0); /* RTS0 */
- if (pins & ATMEL_UART_CTS)
- at91_set_A_periph(AT91_PIN_PA29, 0); /* CTS0 */
-}
-
-static struct resource uart1_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_US1,
- .end = AT91SAM9263_BASE_US1 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_US1,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_US1,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart1_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart1_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_uart1_device = {
- .name = "atmel_usart",
- .id = 2,
- .dev = {
- .dma_mask = &uart1_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart1_data,
- },
- .resource = uart1_resources,
- .num_resources = ARRAY_SIZE(uart1_resources),
-};
-
-static inline void configure_usart1_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PD0, 1); /* TXD1 */
- at91_set_A_periph(AT91_PIN_PD1, 0); /* RXD1 */
-
- if (pins & ATMEL_UART_RTS)
- at91_set_B_periph(AT91_PIN_PD7, 0); /* RTS1 */
- if (pins & ATMEL_UART_CTS)
- at91_set_B_periph(AT91_PIN_PD8, 0); /* CTS1 */
-}
-
-static struct resource uart2_resources[] = {
- [0] = {
- .start = AT91SAM9263_BASE_US2,
- .end = AT91SAM9263_BASE_US2 + SZ_16K - 1,
- .flags = IORESOURCE_MEM,
- },
- [1] = {
- .start = NR_IRQS_LEGACY + AT91SAM9263_ID_US2,
- .end = NR_IRQS_LEGACY + AT91SAM9263_ID_US2,
- .flags = IORESOURCE_IRQ,
- },
-};
-
-static struct atmel_uart_data uart2_data = {
- .use_dma_tx = 1,
- .use_dma_rx = 1,
-};
-
-static u64 uart2_dmamask = DMA_BIT_MASK(32);
-
-static struct platform_device at91sam9263_uart2_device = {
- .name = "atmel_usart",
- .id = 3,
- .dev = {
- .dma_mask = &uart2_dmamask,
- .coherent_dma_mask = DMA_BIT_MASK(32),
- .platform_data = &uart2_data,
- },
- .resource = uart2_resources,
- .num_resources = ARRAY_SIZE(uart2_resources),
-};
-
-static inline void configure_usart2_pins(unsigned pins)
-{
- at91_set_A_periph(AT91_PIN_PD2, 1); /* TXD2 */
- at91_set_A_periph(AT91_PIN_PD3, 0); /* RXD2 */
-
- if (pins & ATMEL_UART_RTS)
- at91_set_B_periph(AT91_PIN_PD5, 0); /* RTS2 */
- if (pins & ATMEL_UART_CTS)
- at91_set_B_periph(AT91_PIN_PD6, 0); /* CTS2 */
-}
-
-static struct platform_device *__initdata at91_uarts[ATMEL_MAX_UART]; /* the UARTs to use */
-
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins)
-{
- struct platform_device *pdev;
- struct atmel_uart_data *pdata;
-
- switch (id) {
- case 0: /* DBGU */
- pdev = &at91sam9263_dbgu_device;
- configure_dbgu_pins();
- break;
- case AT91SAM9263_ID_US0:
- pdev = &at91sam9263_uart0_device;
- configure_usart0_pins(pins);
- break;
- case AT91SAM9263_ID_US1:
- pdev = &at91sam9263_uart1_device;
- configure_usart1_pins(pins);
- break;
- case AT91SAM9263_ID_US2:
- pdev = &at91sam9263_uart2_device;
- configure_usart2_pins(pins);
- break;
- default:
- return;
- }
- pdata = pdev->dev.platform_data;
- pdata->num = portnr; /* update to mapped ID */
-
- if (portnr < ATMEL_MAX_UART)
- at91_uarts[portnr] = pdev;
-}
-
-void __init at91_add_device_serial(void)
-{
- int i;
-
- for (i = 0; i < ATMEL_MAX_UART; i++) {
- if (at91_uarts[i])
- platform_device_register(at91_uarts[i]);
- }
-}
-#else
-void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins) {}
-void __init at91_add_device_serial(void) {}
-#endif
-
-
-/* -------------------------------------------------------------------- */
-/*
- * These devices are always present and don't need any board-specific
- * setup.
- */
-static int __init at91_add_standard_devices(void)
-{
- if (of_have_populated_dt())
- return 0;
-
- at91_add_device_rtt();
- at91_add_device_watchdog();
- at91_add_device_tc();
- return 0;
-}
-
-arch_initcall(at91_add_standard_devices);
+++ /dev/null
-/*
- * linux/arch/arm/mach-at91/board-sam9263ek.c
- *
- * Copyright (C) 2005 SAN People
- * Copyright (C) 2007 Atmel Corporation.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include <linux/types.h>
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/ads7846.h>
-#include <linux/platform_data/at24.h>
-#include <linux/fb.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/leds.h>
-#include <linux/pwm.h>
-#include <linux/leds_pwm.h>
-
-#include <video/atmel_lcdc.h>
-
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/hardware.h>
-#include <mach/at91sam9_smc.h>
-#include <mach/system_rev.h>
-
-#include "at91_aic.h"
-#include "board.h"
-#include "sam9_smc.h"
-#include "generic.h"
-#include "gpio.h"
-
-
-static void __init ek_init_early(void)
-{
- /* Initialize processor: 16.367 MHz crystal */
- at91_initialize(16367660);
-}
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
- .ports = 2,
- .vbus_pin = { AT91_PIN_PA24, AT91_PIN_PA21 },
- .vbus_pin_active_low = {1, 1},
- .overcurrent_pin= {-EINVAL, -EINVAL},
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
- .vbus_pin = AT91_PIN_PA25,
- .pullup_pin = -EINVAL, /* pull-up driven by UDC */
-};
-
-
-/*
- * ADS7846 Touchscreen
- */
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
-static int ads7843_pendown_state(void)
-{
- return !at91_get_gpio_value(AT91_PIN_PA15); /* Touchscreen PENIRQ */
-}
-
-static struct ads7846_platform_data ads_info = {
- .model = 7843,
- .x_min = 150,
- .x_max = 3830,
- .y_min = 190,
- .y_max = 3830,
- .vref_delay_usecs = 100,
- .x_plate_ohms = 450,
- .y_plate_ohms = 250,
- .pressure_max = 15000,
- .debounce_max = 1,
- .debounce_rep = 0,
- .debounce_tol = (~0),
- .get_pendown_state = ads7843_pendown_state,
-};
-
-static void __init ek_add_device_ts(void)
-{
- at91_set_B_periph(AT91_PIN_PA15, 1); /* External IRQ1, with pullup */
- at91_set_gpio_input(AT91_PIN_PA31, 1); /* Touchscreen BUSY signal */
-}
-#else
-static void __init ek_add_device_ts(void) {}
-#endif
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
- { /* DataFlash card */
- .modalias = "mtd_dataflash",
- .chip_select = 0,
- .max_speed_hz = 15 * 1000 * 1000,
- .bus_num = 0,
- },
-#endif
-#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
- {
- .modalias = "ads7846",
- .chip_select = 3,
- .max_speed_hz = 125000 * 26, /* (max sample rate @ 3V) * (cmd + data + overhead) */
- .bus_num = 0,
- .platform_data = &ads_info,
- .irq = NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
- },
-#endif
-};
-
-
-/*
- * MCI (SD/MMC)
- */
-static struct mci_platform_data __initdata mci1_data = {
- .slot[0] = {
- .bus_width = 4,
- .detect_pin = AT91_PIN_PE18,
- .wp_pin = AT91_PIN_PE19,
- },
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct macb_platform_data __initdata ek_macb_data = {
- .phy_irq_pin = AT91_PIN_PE31,
- .is_rmii = 1,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
- {
- .name = "Partition 1",
- .offset = 0,
- .size = SZ_64M,
- },
- {
- .name = "Partition 2",
- .offset = MTDPART_OFS_NXTBLK,
- .size = MTDPART_SIZ_FULL,
- },
-};
-
-static struct atmel_nand_data __initdata ek_nand_data = {
- .ale = 21,
- .cle = 22,
- .det_pin = -EINVAL,
- .rdy_pin = AT91_PIN_PA22,
- .enable_pin = AT91_PIN_PD15,
- .ecc_mode = NAND_ECC_SOFT,
- .on_flash_bbt = 1,
- .parts = ek_nand_partition,
- .num_parts = ARRAY_SIZE(ek_nand_partition),
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
- .ncs_read_setup = 0,
- .nrd_setup = 1,
- .ncs_write_setup = 0,
- .nwe_setup = 1,
-
- .ncs_read_pulse = 3,
- .nrd_pulse = 3,
- .ncs_write_pulse = 3,
- .nwe_pulse = 3,
-
- .read_cycle = 5,
- .write_cycle = 5,
-
- .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
- .tdf_cycles = 2,
-};
-
-static void __init ek_add_device_nand(void)
-{
- ek_nand_data.bus_width_16 = board_have_nand_16bit();
- /* setup bus-width (8 or 16) */
- if (ek_nand_data.bus_width_16)
- ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
- else
- ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
- /* configure chip-select 3 (NAND) */
- sam9_smc_configure(0, 3, &ek_nand_smc_config);
-
- at91_add_device_nand(&ek_nand_data);
-}
-
-
-/*
- * I2C devices
- */
-static struct at24_platform_data at24c512 = {
- .byte_len = SZ_512K / 8,
- .page_size = 128,
- .flags = AT24_FLAG_ADDR16,
-};
-
-
-static struct i2c_board_info __initdata ek_i2c_devices[] = {
- {
- I2C_BOARD_INFO("24c512", 0x50),
- .platform_data = &at24c512,
- },
- /* more devices can be added using expansion connectors */
-};
-
-/*
- * LCD Controller
- */
-#if defined(CONFIG_FB_ATMEL) || defined(CONFIG_FB_ATMEL_MODULE)
-static struct fb_videomode at91_tft_vga_modes[] = {
- {
- .name = "TX09D50VM1CCA @ 60",
- .refresh = 60,
- .xres = 240, .yres = 320,
- .pixclock = KHZ2PICOS(4965),
-
- .left_margin = 1, .right_margin = 33,
- .upper_margin = 1, .lower_margin = 0,
- .hsync_len = 5, .vsync_len = 1,
-
- .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
- .vmode = FB_VMODE_NONINTERLACED,
- },
-};
-
-static struct fb_monspecs at91fb_default_monspecs = {
- .manufacturer = "HIT",
- .monitor = "TX09D70VM1CCA",
-
- .modedb = at91_tft_vga_modes,
- .modedb_len = ARRAY_SIZE(at91_tft_vga_modes),
- .hfmin = 15000,
- .hfmax = 64000,
- .vfmin = 50,
- .vfmax = 150,
-};
-
-#define AT91SAM9263_DEFAULT_LCDCON2 (ATMEL_LCDC_MEMOR_LITTLE \
- | ATMEL_LCDC_DISTYPE_TFT \
- | ATMEL_LCDC_CLKMOD_ALWAYSACTIVE)
-
-static void at91_lcdc_power_control(struct atmel_lcdfb_pdata *pdata, int on)
-{
- at91_set_gpio_value(AT91_PIN_PA30, on);
-}
-
-/* Driver datas */
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data = {
- .lcdcon_is_backlight = true,
- .default_bpp = 16,
- .default_dmacon = ATMEL_LCDC_DMAEN,
- .default_lcdcon2 = AT91SAM9263_DEFAULT_LCDCON2,
- .default_monspecs = &at91fb_default_monspecs,
- .atmel_lcdfb_power_control = at91_lcdc_power_control,
- .guard_time = 1,
-};
-
-#else
-static struct atmel_lcdfb_pdata __initdata ek_lcdc_data;
-#endif
-
-
-/*
- * GPIO Buttons
- */
-#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
-static struct gpio_keys_button ek_buttons[] = {
- { /* BP1, "leftclic" */
- .code = BTN_LEFT,
- .gpio = AT91_PIN_PC5,
- .active_low = 1,
- .desc = "left_click",
- .wakeup = 1,
- },
- { /* BP2, "rightclic" */
- .code = BTN_RIGHT,
- .gpio = AT91_PIN_PC4,
- .active_low = 1,
- .desc = "right_click",
- .wakeup = 1,
- }
-};
-
-static struct gpio_keys_platform_data ek_button_data = {
- .buttons = ek_buttons,
- .nbuttons = ARRAY_SIZE(ek_buttons),
-};
-
-static struct platform_device ek_button_device = {
- .name = "gpio-keys",
- .id = -1,
- .num_resources = 0,
- .dev = {
- .platform_data = &ek_button_data,
- }
-};
-
-static void __init ek_add_device_buttons(void)
-{
- at91_set_GPIO_periph(AT91_PIN_PC5, 1); /* left button */
- at91_set_deglitch(AT91_PIN_PC5, 1);
- at91_set_GPIO_periph(AT91_PIN_PC4, 1); /* right button */
- at91_set_deglitch(AT91_PIN_PC4, 1);
-
- platform_device_register(&ek_button_device);
-}
-#else
-static void __init ek_add_device_buttons(void) {}
-#endif
-
-
-/*
- * AC97
- * reset_pin is not connected: NRST
- */
-static struct ac97c_platform_data ek_ac97_data = {
- .reset_pin = -EINVAL,
-};
-
-
-/*
- * LEDs ... these could all be PWM-driven, for variable brightness
- */
-static struct gpio_led ek_leds[] = {
- { /* "right" led, green, userled2 (could be driven by pwm2) */
- .name = "ds2",
- .gpio = AT91_PIN_PC29,
- .active_low = 1,
- .default_trigger = "nand-disk",
- },
- { /* "power" led, yellow (could be driven by pwm0) */
- .name = "ds3",
- .gpio = AT91_PIN_PB7,
- .default_trigger = "heartbeat",
- },
-#if !IS_ENABLED(CONFIG_LEDS_PWM)
- {
- .name = "ds1",
- .gpio = AT91_PIN_PB8,
- .active_low = 1,
- .default_trigger = "none",
- }
-#endif
-};
-
-/*
- * PWM Leds
- */
-static struct pwm_lookup pwm_lookup[] = {
- PWM_LOOKUP("at91sam9rl-pwm", 1, "leds_pwm", "ds1",
- 5000, PWM_POLARITY_INVERSED),
-};
-
-#if IS_ENABLED(CONFIG_LEDS_PWM)
-static struct led_pwm pwm_leds[] = {
- {
- .name = "ds1",
- .max_brightness = 255,
- },
-};
-
-static struct led_pwm_platform_data pwm_data = {
- .num_leds = ARRAY_SIZE(pwm_leds),
- .leds = pwm_leds,
-};
-
-static struct platform_device leds_pwm = {
- .name = "leds_pwm",
- .id = -1,
- .dev = {
- .platform_data = &pwm_data,
- },
-};
-#endif
-
-
-/*
- * CAN
- */
-static void sam9263ek_transceiver_switch(int on)
-{
- if (on) {
- at91_set_gpio_output(AT91_PIN_PA18, 1); /* CANRXEN */
- at91_set_gpio_output(AT91_PIN_PA19, 0); /* CANRS */
- } else {
- at91_set_gpio_output(AT91_PIN_PA18, 0); /* CANRXEN */
- at91_set_gpio_output(AT91_PIN_PA19, 1); /* CANRS */
- }
-}
-
-static struct at91_can_data ek_can_data = {
- .transceiver_switch = sam9263ek_transceiver_switch,
-};
-
-static struct platform_device *devices[] __initdata = {
-#if IS_ENABLED(CONFIG_LEDS_PWM)
- &leds_pwm,
-#endif
-};
-
-static void __init ek_board_init(void)
-{
- at91_register_devices();
-
- /* Serial */
- /* DBGU on ttyS0. (Rx & Tx only) */
- at91_register_uart(0, 0, 0);
-
- /* USART0 on ttyS1. (Rx, Tx, RTS, CTS) */
- at91_register_uart(AT91SAM9263_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS);
- at91_add_device_serial();
- /* USB Host */
- at91_add_device_usbh(&ek_usbh_data);
- /* USB Device */
- at91_add_device_udc(&ek_udc_data);
- /* SPI */
- at91_set_gpio_output(AT91_PIN_PE20, 1); /* select spi0 clock */
- at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
- /* Touchscreen */
- ek_add_device_ts();
- /* MMC */
- at91_add_device_mci(1, &mci1_data);
- /* Ethernet */
- at91_add_device_eth(&ek_macb_data);
- /* NAND */
- ek_add_device_nand();
- /* I2C */
- at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
- /* LCD Controller */
- at91_add_device_lcdc(&ek_lcdc_data);
- /* Push Buttons */
- ek_add_device_buttons();
- /* AC97 */
- at91_add_device_ac97(&ek_ac97_data);
- /* LEDs */
- at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
- pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
-#if IS_ENABLED(CONFIG_LEDS_PWM)
- at91_add_device_pwm(1 << AT91_PWM1);
-#endif
- /* CAN */
- at91_add_device_can(&ek_can_data);
- /* Other platform devices */
- platform_add_devices(devices, ARRAY_SIZE(devices));
-}
-
-MACHINE_START(AT91SAM9263EK, "Atmel AT91SAM9263-EK")
- /* Maintainer: Atmel */
- .init_time = at91_init_time,
- .map_io = at91_map_io,
- .handle_irq = at91_aic_handle_irq,
- .init_early = ek_init_early,
- .init_irq = at91_init_irq_default,
- .init_machine = ek_board_init,
-MACHINE_END
projects / openwrt / staging / blogic.git / commitdiff