--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
-@@ -239,6 +239,11 @@ config PHY_XGENE
+@@ -239,6 +239,11 @@
help
This option enables support for APM X-Gene SoC multi-purpose PHY.
depends on RESET_CONTROLLER
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
-@@ -31,3 +31,4 @@ obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) +=
+@@ -31,3 +31,4 @@
obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
obj-$(CONFIG_PHY_STIH41X_USB) += phy-stih41x-usb.o
+obj-$(CONFIG_PHY_RALINK_USB) += phy-ralink-usb.o
--- /dev/null
+++ b/drivers/phy/phy-ralink-usb.c
-@@ -0,0 +1,175 @@
+@@ -0,0 +1,228 @@
+/*
+ * Allwinner ralink USB phy driver
+ *
-+ * Copyright (C) 2014 John Crispin <blogic@openwrt.org>
++ * Copyright (C) 2016 John Crispin <blogic@openwrt.org>
+ *
+ * Based on code from
+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
+#define RT_SYSC_REG_CLKCFG1 0x030
+#define RT_SYSC_REG_USB_PHY_CFG 0x05c
+
++#define OFS_U2_PHY_AC0 0x00
++#define OFS_U2_PHY_AC1 0x04
++#define OFS_U2_PHY_AC2 0x08
++#define OFS_U2_PHY_ACR0 0x10
++#define OFS_U2_PHY_ACR1 0x14
++#define OFS_U2_PHY_ACR2 0x18
++#define OFS_U2_PHY_ACR3 0x1C
++#define OFS_U2_PHY_ACR4 0x20
++#define OFS_U2_PHY_AMON0 0x24
++#define OFS_U2_PHY_DCR0 0x60
++#define OFS_U2_PHY_DCR1 0x64
++#define OFS_U2_PHY_DTM0 0x68
++#define OFS_U2_PHY_DTM1 0x6C
++
+#define RT_RSTCTRL_UDEV BIT(25)
+#define RT_RSTCTRL_UHST BIT(22)
+#define RT_SYSCFG1_USB0_HOST_MODE BIT(10)
+#define USB_PHY_UTMI_8B60M BIT(1)
+#define UDEV_WAKEUP BIT(0)
+
-+static atomic_t usb_pwr_ref = ATOMIC_INIT(0);
-+static struct reset_control *rstdev;
-+static struct reset_control *rsthost;
-+static u32 phy_clk;
-+static struct phy *rt_phy;
++struct ralink_usb_phy {
++ struct reset_control *rstdev;
++ struct reset_control *rsthost;
++ u32 clk;
++ struct phy *phy;
++ void __iomem *base;
++};
+
-+static void usb_phy_enable(int state)
++static void u2_phy_w32(struct ralink_usb_phy *phy, u32 val, u32 reg)
+{
-+ if (state)
-+ rt_sysc_m32(0, phy_clk, RT_SYSC_REG_CLKCFG1);
-+ else
-+ rt_sysc_m32(phy_clk, 0, RT_SYSC_REG_CLKCFG1);
-+ mdelay(100);
++ iowrite32(val, phy->base + reg);
+}
+
-+static int ralink_usb_phy_init(struct phy *_phy)
++static u32 u2_phy_r32(struct ralink_usb_phy *phy, u32 reg)
+{
-+ return 0;
++ return ioread32(phy->base + reg);
+}
+
-+static int ralink_usb_phy_exit(struct phy *_phy)
++static void
++u2_phy_init(struct ralink_usb_phy *phy)
+{
-+ return 0;
++ u2_phy_r32(phy, OFS_U2_PHY_AC2);
++ u2_phy_r32(phy, OFS_U2_PHY_ACR0);
++ u2_phy_r32(phy, OFS_U2_PHY_DCR0);
++
++ u2_phy_w32(phy, 0x00ffff02, OFS_U2_PHY_DCR0);
++ u2_phy_r32(phy, OFS_U2_PHY_DCR0);
++ u2_phy_w32(phy, 0x00555502, OFS_U2_PHY_DCR0);
++ u2_phy_r32(phy, OFS_U2_PHY_DCR0);
++ u2_phy_w32(phy, 0x00aaaa02, OFS_U2_PHY_DCR0);
++ u2_phy_r32(phy, OFS_U2_PHY_DCR0);
++ u2_phy_w32(phy, 0x00000402, OFS_U2_PHY_DCR0);
++ u2_phy_r32(phy, OFS_U2_PHY_DCR0);
++ u2_phy_w32(phy, 0x0048086a, OFS_U2_PHY_AC0);
++ u2_phy_w32(phy, 0x4400001c, OFS_U2_PHY_AC1);
++ u2_phy_w32(phy, 0xc0200000, OFS_U2_PHY_ACR3);
++ u2_phy_w32(phy, 0x02000000, OFS_U2_PHY_DTM0);
+}
+
+static int ralink_usb_phy_power_on(struct phy *_phy)
+{
-+ if (atomic_inc_return(&usb_pwr_ref) == 1) {
-+ int host = 1;
-+ u32 t;
-+
-+ usb_phy_enable(1);
-+
-+ if (host) {
-+ rt_sysc_m32(0, RT_SYSCFG1_USB0_HOST_MODE, RT_SYSC_REG_SYSCFG1);
-+ if (!IS_ERR(rsthost))
-+ reset_control_deassert(rsthost);
-+ if (!IS_ERR(rstdev))
-+ reset_control_deassert(rstdev);
-+ } else {
-+ rt_sysc_m32(RT_SYSCFG1_USB0_HOST_MODE, 0, RT_SYSC_REG_SYSCFG1);
-+ if (!IS_ERR(rstdev))
-+ reset_control_deassert(rstdev);
-+ }
-+ mdelay(100);
-+
-+ t = rt_sysc_r32(RT_SYSC_REG_USB_PHY_CFG);
-+ dev_info(&_phy->dev, "remote usb device wakeup %s\n",
-+ (t & UDEV_WAKEUP) ? ("enabbled") : ("disabled"));
-+ if (t & USB_PHY_UTMI_8B60M)
-+ dev_info(&_phy->dev, "UTMI 8bit 60MHz\n");
-+ else
-+ dev_info(&_phy->dev, "UTMI 16bit 30MHz\n");
-+ }
++ struct ralink_usb_phy *phy = phy_get_drvdata(_phy);
++ u32 t;
++
++ /* enable the phy */
++ rt_sysc_m32(0, phy->clk, RT_SYSC_REG_CLKCFG1);
++
++ /* setup host mode */
++ rt_sysc_m32(0, RT_SYSCFG1_USB0_HOST_MODE, RT_SYSC_REG_SYSCFG1);
++
++ /* deassert the reset lines */
++ reset_control_deassert(phy->rsthost);
++ reset_control_deassert(phy->rstdev);
++
++ /*
++ * The SDK kernel had a delay of 100ms. however on device
++ * testing showed that 10ms is enough
++ */
++ mdelay(10);
++
++ if (!IS_ERR(phy->base))
++ u2_phy_init(phy);
++
++ /* print some status info */
++ t = rt_sysc_r32(RT_SYSC_REG_USB_PHY_CFG);
++ dev_info(&phy->phy->dev, "remote usb device wakeup %s\n",
++ (t & UDEV_WAKEUP) ? ("enabled") : ("disabled"));
++ if (t & USB_PHY_UTMI_8B60M)
++ dev_info(&phy->phy->dev, "UTMI 8bit 60MHz\n");
++ else
++ dev_info(&phy->phy->dev, "UTMI 16bit 30MHz\n");
+
+ return 0;
+}
+
+static int ralink_usb_phy_power_off(struct phy *_phy)
+{
-+ if (atomic_dec_return(&usb_pwr_ref) == 0) {
-+ usb_phy_enable(0);
-+ if (!IS_ERR(rstdev))
-+ reset_control_assert(rstdev);
-+ if (!IS_ERR(rsthost))
-+ reset_control_assert(rsthost);
-+ }
++ struct ralink_usb_phy *phy = phy_get_drvdata(_phy);
++
++ /* assert the reset lines */
++ reset_control_assert(phy->rstdev);
++ reset_control_assert(phy->rsthost);
++
++ /* disable the phy */
++ rt_sysc_m32(phy->clk, 0, RT_SYSC_REG_CLKCFG1);
+
+ return 0;
+}
+
+static struct phy_ops ralink_usb_phy_ops = {
-+ .init = ralink_usb_phy_init,
-+ .exit = ralink_usb_phy_exit,
+ .power_on = ralink_usb_phy_power_on,
+ .power_off = ralink_usb_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
-+static struct phy *ralink_usb_phy_xlate(struct device *dev,
-+ struct of_phandle_args *args)
-+{
-+ return rt_phy;
-+}
-+
+static const struct of_device_id ralink_usb_phy_of_match[] = {
-+ { .compatible = "ralink,rt3xxx-usbphy", .data = (void *) (RT_CLKCFG1_UPHY1_CLK_EN | RT_CLKCFG1_UPHY0_CLK_EN) },
-+ { .compatible = "ralink,mt7620a-usbphy", .data = (void *) (MT7620_CLKCFG1_UPHY1_CLK_EN | MT7620_CLKCFG1_UPHY0_CLK_EN) },
++ {
++ .compatible = "ralink,rt3xxx-usbphy",
++ .data = (void *) (RT_CLKCFG1_UPHY1_CLK_EN |
++ RT_CLKCFG1_UPHY0_CLK_EN)
++ },
++ {
++ .compatible = "ralink,mt7620a-usbphy",
++ .data = (void *) (MT7620_CLKCFG1_UPHY1_CLK_EN |
++ MT7620_CLKCFG1_UPHY0_CLK_EN) },
+ { },
+};
+MODULE_DEVICE_TABLE(of, ralink_usb_phy_of_match);
+
+static int ralink_usb_phy_probe(struct platform_device *pdev)
+{
++ struct resource *res;
+ struct device *dev = &pdev->dev;
+ struct phy_provider *phy_provider;
+ const struct of_device_id *match;
++ struct ralink_usb_phy *phy;
++
++ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
++ if (!phy)
++ return -ENOMEM;
+
+ match = of_match_device(ralink_usb_phy_of_match, &pdev->dev);
-+ phy_clk = (int) match->data;
++ if (!match)
++ return -ENODEV;
++
++ phy->clk = (int) match->data;
+
-+ rsthost = devm_reset_control_get(&pdev->dev, "host");
-+ rstdev = devm_reset_control_get(&pdev->dev, "device");
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ phy->base = devm_ioremap_resource(&pdev->dev, res);
++
++ phy->rsthost = devm_reset_control_get(&pdev->dev, "host");
++ if (IS_ERR(phy->rsthost)) {
++ dev_err(dev, "host reset is missing\n");
++ return PTR_ERR(phy->rsthost);
++ }
++
++ phy->rstdev = devm_reset_control_get(&pdev->dev, "device");
++ if (IS_ERR(phy->rstdev)) {
++ dev_err(dev, "device reset is missing\n");
++ return PTR_ERR(phy->rstdev);
++ }
+
-+ rt_phy = devm_phy_create(dev, NULL, &ralink_usb_phy_ops, NULL);
-+ if (IS_ERR(rt_phy)) {
++ phy->phy = devm_phy_create(dev, NULL, &ralink_usb_phy_ops, NULL);
++ if (IS_ERR(phy->phy)) {
+ dev_err(dev, "failed to create PHY\n");
-+ return PTR_ERR(rt_phy);
++ return PTR_ERR(phy->phy);
+ }
++ phy_set_drvdata(phy->phy, phy);
+
-+ phy_provider = devm_of_phy_provider_register(dev, ralink_usb_phy_xlate);
++ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+ return PTR_ERR_OR_ZERO(phy_provider);
+}
projects / openwrt / svn-archive / archive.git / commitdiff