Use kirkwood_nand_init instead of manually registering the nand driver

This fixes that the device would hang during boot.

SVN-Revision: 22837

diff --git a/target/linux/kirkwood/patches/100-dockstar.patch b/target/linux/kirkwood/patches/100-dockstar.patch
index f6ac90b7a8b70596b55db70aa516588f82b3bdef..59334b4cda0de3dbaca5c2ca0c5524db49aa9e1f 100644 (file)
--- a/target/linux/kirkwood/patches/100-dockstar.patch
+++ b/target/linux/kirkwood/patches/100-dockstar.patch
@@ -38,7 +38,7 @@ Signed-off-by: Eric Cooper <ecc@xxxxxxx>
  obj-$(CONFIG_MACH_TS219)              += ts219-setup.o tsx1x-common.o
 --- /dev/null
 +++ b/arch/arm/mach-kirkwood/dockstar-setup.c
-@@ -0,0 +1,148 @@
+@@ -0,0 +1,121 @@
 +/*
 + * arch/arm/mach-kirkwood/dockstar-setup.c
 + *
@@ -61,7 +61,6 @@ Signed-off-by: Eric Cooper <ecc@xxxxxxx>
 +#include <asm/mach/arch.h>
 +#include <mach/kirkwood.h>
 +#include <plat/mvsdio.h>
-+#include <plat/orion_nand.h>
 +#include "common.h"
 +#include "mpp.h"
 +
@@ -81,7 +80,7 @@ Signed-off-by: Eric Cooper <ecc@xxxxxxx>
 +      }, {
 +              .name = "rootfs",
 +              .offset = MTDPART_OFS_NXTBLK,
-+              .size = SZ_64M,
++              .size = SZ_32M,
 +      }, {
 +              .name = "data",
 +              .offset = MTDPART_OFS_NXTBLK,
@@ -89,33 +88,6 @@ Signed-off-by: Eric Cooper <ecc@xxxxxxx>
 +      },
 +};
 +
-+static struct resource dockstar_nand_resource = {
-+      .flags          = IORESOURCE_MEM,
-+      .start          = KIRKWOOD_NAND_MEM_PHYS_BASE,
-+      .end            = KIRKWOOD_NAND_MEM_PHYS_BASE +
-+                        KIRKWOOD_NAND_MEM_SIZE - 1,
-+};
-+
-+static struct orion_nand_data dockstar_nand_data = {
-+      .parts          = dockstar_nand_parts,
-+      .nr_parts       = ARRAY_SIZE(dockstar_nand_parts),
-+      .cle            = 0,
-+      .ale            = 1,
-+      .width          = 8,
-+      .chip_delay     = 25,
-+};
-+
-+static struct platform_device dockstar_nand_flash = {
-+      .name           = "orion_nand",
-+      .id             = -1,
-+      .dev            = {
-+              .platform_data  = &dockstar_nand_data,
-+      },
-+      .resource       = &dockstar_nand_resource,
-+      .num_resources  = 1,
-+};
-+
-+
 +static struct mv643xx_eth_platform_data dockstar_ge00_data = {
 +      .phy_addr       = MV643XX_ETH_PHY_ADDR(0),
 +};
@@ -172,9 +144,10 @@ Signed-off-by: Eric Cooper <ecc@xxxxxxx>
 +              printk(KERN_ERR "can't set up GPIO 29 (USB Power Enable)\n");
 +      kirkwood_ehci_init();
 +
++      kirkwood_nand_init(ARRAY_AND_SIZE(dockstar_nand_parts), 25);
++
 +      kirkwood_ge00_init(&dockstar_ge00_data);
 +
-+      platform_device_register(&dockstar_nand_flash);
 +      platform_device_register(&dockstar_leds);
 +}
 +