libs-y += arch/$(ARCH)/imx-common/
endif
-ifneq (,$(filter $(SOC), kirkwood))
+ifneq (,$(filter $(SOC), armada-xp kirkwood))
libs-y += arch/$(ARCH)/mvebu-common/
endif
--- /dev/null
+#
+# Copyright (C) 2014 Stefan Roese <sr@denx.de>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y = cpu.o
--- /dev/null
+/*
+ * Copyright (C) 2014 Stefan Roese <sr@denx.de>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+
+#define DDR_BASE_CS_OFF(n) (0x0000 + ((n) << 3))
+#define DDR_SIZE_CS_OFF(n) (0x0004 + ((n) << 3))
+
+static struct mbus_win windows[] = {
+ /* PCIE MEM address space */
+ { DEFADR_PCI_MEM, 256 << 20, CPU_TARGET_PCIE13, CPU_ATTR_PCIE_MEM },
+
+ /* PCIE IO address space */
+ { DEFADR_PCI_IO, 64 << 10, CPU_TARGET_PCIE13, CPU_ATTR_PCIE_IO },
+
+ /* SPI */
+ { DEFADR_SPIF, 8 << 20, CPU_TARGET_DEVICEBUS_BOOTROM_SPI,
+ CPU_ATTR_SPIFLASH },
+
+ /* NOR */
+ { DEFADR_BOOTROM, 8 << 20, CPU_TARGET_DEVICEBUS_BOOTROM_SPI,
+ CPU_ATTR_BOOTROM },
+};
+
+void reset_cpu(unsigned long ignored)
+{
+ struct mvebu_system_registers *reg =
+ (struct mvebu_system_registers *)MVEBU_SYSTEM_REG_BASE;
+
+ writel(readl(®->rstoutn_mask) | 1, ®->rstoutn_mask);
+ writel(readl(®->sys_soft_rst) | 1, ®->sys_soft_rst);
+ while (1)
+ ;
+}
+
+#if defined(CONFIG_DISPLAY_CPUINFO)
+int print_cpuinfo(void)
+{
+ u16 devid = (readl(MVEBU_REG_PCIE_DEVID) >> 16) & 0xffff;
+ u8 revid = readl(MVEBU_REG_PCIE_REVID) & 0xff;
+
+ puts("SoC: ");
+
+ switch (devid) {
+ case SOC_MV78460_ID:
+ puts("MV78460-");
+ break;
+ default:
+ puts("Unknown-");
+ break;
+ }
+
+ switch (revid) {
+ case 1:
+ puts("A0\n");
+ break;
+ case 2:
+ puts("B0\n");
+ break;
+ default:
+ puts("??\n");
+ break;
+ }
+
+ return 0;
+}
+#endif /* CONFIG_DISPLAY_CPUINFO */
+
+/*
+ * This function initialize Controller DRAM Fastpath windows.
+ * It takes the CS size information from the 0x1500 scratch registers
+ * and sets the correct windows sizes and base addresses accordingly.
+ *
+ * These values are set in the scratch registers by the Marvell
+ * DDR3 training code, which is executed by the BootROM before the
+ * main payload (U-Boot) is executed. This training code is currently
+ * only available in the Marvell U-Boot version. It needs to be
+ * ported to mainline U-Boot SPL at some point.
+ */
+static void update_sdram_window_sizes(void)
+{
+ u64 base = 0;
+ u32 size, temp;
+ int i;
+
+ for (i = 0; i < SDRAM_MAX_CS; i++) {
+ size = readl((MVEBU_SDRAM_SCRATCH + (i * 8))) & SDRAM_ADDR_MASK;
+ if (size != 0) {
+ size |= ~(SDRAM_ADDR_MASK);
+
+ /* Set Base Address */
+ temp = (base & 0xFF000000ll) | ((base >> 32) & 0xF);
+ writel(temp, MVEBU_SDRAM_BASE + DDR_BASE_CS_OFF(i));
+
+ /*
+ * Check if out of max window size and resize
+ * the window
+ */
+ temp = (readl(MVEBU_SDRAM_BASE + DDR_SIZE_CS_OFF(i)) &
+ ~(SDRAM_ADDR_MASK)) | 1;
+ temp |= (size & SDRAM_ADDR_MASK);
+ writel(temp, MVEBU_SDRAM_BASE + DDR_SIZE_CS_OFF(i));
+
+ base += ((u64)size + 1);
+ } else {
+ /*
+ * Disable window if not used, otherwise this
+ * leads to overlapping enabled windows with
+ * pretty strange results
+ */
+ clrbits_le32(MVEBU_SDRAM_BASE + DDR_SIZE_CS_OFF(i), 1);
+ }
+ }
+}
+
+#ifdef CONFIG_ARCH_CPU_INIT
+int arch_cpu_init(void)
+{
+ /* Linux expects the internal registers to be at 0xf1000000 */
+ writel(SOC_REGS_PHY_BASE, INTREG_BASE_ADDR_REG);
+
+ /*
+ * We need to call mvebu_mbus_probe() before calling
+ * update_sdram_window_sizes() as it disables all previously
+ * configured mbus windows and then configures them as
+ * required for U-Boot. Calling update_sdram_window_sizes()
+ * without this configuration will not work, as the internal
+ * registers can't be accessed reliably because of potenial
+ * double mapping.
+ * After updating the SDRAM access windows we need to call
+ * mvebu_mbus_probe() again, as this now correctly configures
+ * the SDRAM areas that are later used by the MVEBU drivers
+ * (e.g. USB, NETA).
+ */
+
+ /*
+ * First disable all windows
+ */
+ mvebu_mbus_probe(NULL, 0);
+
+ /*
+ * Now the SDRAM access windows can be reconfigured using
+ * the information in the SDRAM scratch pad registers
+ */
+ update_sdram_window_sizes();
+
+ /*
+ * Finally the mbus windows can be configured with the
+ * updated SDRAM sizes
+ */
+ mvebu_mbus_probe(windows, ARRAY_SIZE(windows));
+
+ return 0;
+}
+#endif /* CONFIG_ARCH_CPU_INIT */
+
+/*
+ * SOC specific misc init
+ */
+#if defined(CONFIG_ARCH_MISC_INIT)
+int arch_misc_init(void)
+{
+ /* Nothing yet, perhaps we need something here later */
+ return 0;
+}
+#endif /* CONFIG_ARCH_MISC_INIT */
+
+#ifdef CONFIG_MVNETA
+int cpu_eth_init(bd_t *bis)
+{
+ mvneta_initialize(bis, MVEBU_EGIGA0_BASE, 0, CONFIG_PHY_BASE_ADDR + 0);
+ mvneta_initialize(bis, MVEBU_EGIGA1_BASE, 1, CONFIG_PHY_BASE_ADDR + 1);
+ mvneta_initialize(bis, MVEBU_EGIGA2_BASE, 2, CONFIG_PHY_BASE_ADDR + 2);
+ mvneta_initialize(bis, MVEBU_EGIGA3_BASE, 3, CONFIG_PHY_BASE_ADDR + 3);
+
+ return 0;
+}
+#endif
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+void enable_caches(void)
+{
+ /* Enable D-cache. I-cache is already enabled in start.S */
+ dcache_enable();
+}
+#endif
--- /dev/null
+/*
+ * (C) Copyright 2011
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Lei Wen <leiwen@marvell.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * This file should be included in board config header file.
+ *
+ * It supports common definitions for Armada XP platforms
+ */
+
+#ifndef _ARMADA_XP_CONFIG_H
+#define _ARMADA_XP_CONFIG_H
+
+#include <asm/arch/soc.h>
+
+#define MV88F78X60 /* for the DDR training bin_hdr code */
+
+#define CONFIG_SYS_CACHELINE_SIZE 32
+
+/*
+ * By default kwbimage.cfg from board specific folder is used
+ * If for some board, different configuration file need to be used,
+ * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
+ */
+#ifndef CONFIG_SYS_KWD_CONFIG
+#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
+#endif /* CONFIG_SYS_KWD_CONFIG */
+
+/* Add target to build it automatically upon "make" */
+#define CONFIG_BUILD_TARGET "u-boot.kwb"
+
+/* end of 16M scrubbed by training in bootrom */
+#define CONFIG_SYS_INIT_SP_ADDR 0x00FF0000
+#define CONFIG_NR_DRAM_BANKS_MAX 2
+
+#define MV_UART_CONSOLE_BASE MVEBU_UART0_BASE
+
+/*
+ * SPI Flash configuration
+ */
+#ifdef CONFIG_CMD_SF
+#define CONFIG_HARD_SPI 1
+#define CONFIG_KIRKWOOD_SPI 1
+#ifndef CONFIG_ENV_SPI_BUS
+# define CONFIG_ENV_SPI_BUS 0
+#endif
+#ifndef CONFIG_ENV_SPI_CS
+# define CONFIG_ENV_SPI_CS 0
+#endif
+#ifndef CONFIG_ENV_SPI_MAX_HZ
+# define CONFIG_ENV_SPI_MAX_HZ 50000000
+#endif
+#endif
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_MVNETA /* Enable Marvell Gbe Controller Driver */
+#define CONFIG_PHYLIB
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_PHY_GIGE /* GbE speed/duplex detect */
+#endif /* CONFIG_CMD_NET */
+
+/*
+ * I2C related stuff
+ */
+#ifdef CONFIG_CMD_I2C
+#ifndef CONFIG_SYS_I2C_SOFT
+#define CONFIG_I2C_MVTWSI
+#endif
+#define CONFIG_SYS_I2C_SLAVE 0x0
+#define CONFIG_SYS_I2C_SPEED 100000
+#endif
+
+#endif /* _ARMADA_XP_CONFIG_H */
--- /dev/null
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _ARMADA_XP_CPU_H
+#define _ARMADA_XP_CPU_H
+
+#include <asm/system.h>
+
+#ifndef __ASSEMBLY__
+
+#define MVEBU_REG_PCIE_DEVID (MVEBU_REG_PCIE_BASE + 0x00)
+#define MVEBU_REG_PCIE_REVID (MVEBU_REG_PCIE_BASE + 0x08)
+
+enum memory_bank {
+ BANK0,
+ BANK1,
+ BANK2,
+ BANK3
+};
+
+enum cpu_winen {
+ CPU_WIN_DISABLE,
+ CPU_WIN_ENABLE
+};
+
+enum cpu_target {
+ CPU_TARGET_DRAM = 0x0,
+ CPU_TARGET_DEVICEBUS_BOOTROM_SPI = 0x1,
+ CPU_TARGET_ETH23 = 0x3,
+ CPU_TARGET_PCIE02 = 0x4,
+ CPU_TARGET_ETH01 = 0x7,
+ CPU_TARGET_PCIE13 = 0x8,
+ CPU_TARGET_SASRAM = 0x9,
+ CPU_TARGET_NAND = 0xd,
+};
+
+enum cpu_attrib {
+ CPU_ATTR_SASRAM = 0x01,
+ CPU_ATTR_DRAM_CS0 = 0x0e,
+ CPU_ATTR_DRAM_CS1 = 0x0d,
+ CPU_ATTR_DRAM_CS2 = 0x0b,
+ CPU_ATTR_DRAM_CS3 = 0x07,
+ CPU_ATTR_NANDFLASH = 0x2f,
+ CPU_ATTR_SPIFLASH = 0x1e,
+ CPU_ATTR_BOOTROM = 0x1d,
+ CPU_ATTR_PCIE_IO = 0xe0,
+ CPU_ATTR_PCIE_MEM = 0xe8,
+ CPU_ATTR_DEV_CS0 = 0x3e,
+ CPU_ATTR_DEV_CS1 = 0x3d,
+ CPU_ATTR_DEV_CS2 = 0x3b,
+ CPU_ATTR_DEV_CS3 = 0x37,
+};
+
+/*
+ * Default Device Address MAP BAR values
+ */
+#define DEFADR_PCI_MEM 0x90000000
+#define DEFADR_PCI_IO 0xC0000000
+#define DEFADR_SPIF 0xF4000000
+#define DEFADR_BOOTROM 0xF8000000
+
+struct mbus_win {
+ u32 base;
+ u32 size;
+ u8 target;
+ u8 attr;
+};
+
+/*
+ * System registers
+ * Ref: Datasheet sec:A.28
+ */
+struct mvebu_system_registers {
+ u8 pad1[0x60];
+ u32 rstoutn_mask; /* 0x60 */
+ u32 sys_soft_rst; /* 0x64 */
+};
+
+/*
+ * GPIO Registers
+ * Ref: Datasheet sec:A.19
+ */
+struct kwgpio_registers {
+ u32 dout;
+ u32 oe;
+ u32 blink_en;
+ u32 din_pol;
+ u32 din;
+ u32 irq_cause;
+ u32 irq_mask;
+ u32 irq_level;
+};
+
+/*
+ * functions
+ */
+unsigned int mvebu_sdram_bar(enum memory_bank bank);
+unsigned int mvebu_sdram_bs(enum memory_bank bank);
+void mvebu_sdram_size_adjust(enum memory_bank bank);
+int mvebu_mbus_probe(struct mbus_win windows[], int count);
+#endif /* __ASSEMBLY__ */
+#endif /* _ARMADA_XP_CPU_H */
--- /dev/null
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
+ *
+ * Header file for the Marvell's Feroceon CPU core.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _ASM_ARCH_ARMADA_XP_H
+#define _ASM_ARCH_ARMADA_XP_H
+
+#define SOC_MV78460_ID 0x7846
+
+/* TCLK Core Clock definition */
+#ifndef CONFIG_SYS_TCLK
+#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
+#endif
+
+/* SOC specific definations */
+#define INTREG_BASE 0xd0000000
+#define INTREG_BASE_ADDR_REG (INTREG_BASE + 0x20080)
+#define SOC_REGS_PHY_BASE 0xf1000000
+#define MVEBU_REGISTER(x) (SOC_REGS_PHY_BASE + x)
+
+#define MVEBU_SDRAM_SCRATCH (MVEBU_REGISTER(0x01504))
+#define MVEBU_SPI_BASE (MVEBU_REGISTER(0x10600))
+#define MVEBU_TWSI_BASE (MVEBU_REGISTER(0x11000))
+#define MVEBU_UART0_BASE (MVEBU_REGISTER(0x12000))
+#define MVEBU_UART1_BASE (MVEBU_REGISTER(0x12100))
+#define MVEBU_MPP_BASE (MVEBU_REGISTER(0x18000))
+#define MVEBU_GPIO0_BASE (MVEBU_REGISTER(0x18100))
+#define MVEBU_GPIO1_BASE (MVEBU_REGISTER(0x18140))
+#define MVEBU_GPIO2_BASE (MVEBU_REGISTER(0x18180))
+#define MVEBU_SYSTEM_REG_BASE (MVEBU_REGISTER(0x18200))
+#define MVEBU_CPU_WIN_BASE (MVEBU_REGISTER(0x20000))
+#define MVEBU_SDRAM_BASE (MVEBU_REGISTER(0x20180))
+#define MVEBU_TIMER_BASE (MVEBU_REGISTER(0x20300))
+#define MVEBU_EGIGA2_BASE (MVEBU_REGISTER(0x30000))
+#define MVEBU_EGIGA3_BASE (MVEBU_REGISTER(0x34000))
+#define MVEBU_REG_PCIE_BASE (MVEBU_REGISTER(0x40000))
+#define MVEBU_EGIGA0_BASE (MVEBU_REGISTER(0x70000))
+#define MVEBU_EGIGA1_BASE (MVEBU_REGISTER(0x74000))
+
+#define SDRAM_MAX_CS 4
+#define SDRAM_ADDR_MASK 0xFF000000
+
+/* Armada XP GbE controller has 4 ports */
+#define MAX_MVNETA_DEVS 4
+
+/* Kirkwood CPU memory windows */
+#define MVCPU_WIN_CTRL_DATA CPU_WIN_CTRL_DATA
+#define MVCPU_WIN_ENABLE CPU_WIN_ENABLE
+#define MVCPU_WIN_DISABLE CPU_WIN_DISABLE
+
+#endif /* _ASM_ARCH_ARMADA_XP_H */
projects / project / bcm63xx / u-boot.git / commitdiff