This patch removes support for the APM 405CR CPU.
This CPU is EOL and no board uses this chip.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
DECLARE_GLOBAL_DATA_PTR;
-#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \
+#if defined(CONFIG_405GP) || \
defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \
defined(CONFIG_405EX) || defined(CONFIG_440)
#define UDIV_SUBTRACT 0
#define UART0_SDR SDR0_UART0
#define UART1_SDR SDR0_UART1
-#else /* CONFIG_405GP || CONFIG_405CR */
+#else /* CONFIG_405GP */
#define CR0_MASK 0x00001fff
#define CR0_EXTCLK_ENA 0x000000c0
#define CR0_UDIV_POS 1
* Let's handle this in some #ifdef's for the SoC's.
*/
-#if defined(CONFIG_405CR) || defined(CONFIG_405GP)
+#if defined(CONFIG_405GP)
reg = mfdcr(CPC0_CR0) & ~CR0_MASK;
#ifdef CONFIG_SYS_EXT_SERIAL_CLOCK
clk = CONFIG_SYS_EXT_SERIAL_CLOCK;
#else
clk = CONFIG_SYS_BASE_BAUD * 16;
#endif
-#endif /* CONFIG_405CR */
+#endif
#if defined(CONFIG_405EP)
{
return clk;
}
-#endif /* CONFIG_405GP || CONFIG_405CR */
+#endif /* CONFIG_405GP */
puts("405GP Rev. D");
break;
-#ifdef CONFIG_405GP
- case PVR_405GP_RE: /* 405GP rev E and 405CR rev C have same PVR */
+ case PVR_405GP_RE:
puts("405GP Rev. E");
break;
-#endif
-
- case PVR_405CR_RA:
- puts("405CR Rev. A");
- break;
-
- case PVR_405CR_RB:
- puts("405CR Rev. B");
- break;
-
-#ifdef CONFIG_405CR
- case PVR_405CR_RC: /* 405GP rev E and 405CR rev C have same PVR */
- puts("405CR Rev. C");
- break;
-#endif
case PVR_405GPR_RB:
puts("405GPr Rev. B");
* External Bus Controller (EBC) Setup
*/
#if (defined(CONFIG_SYS_EBC_PB0AP) && defined(CONFIG_SYS_EBC_PB0CR))
-#if (defined(CONFIG_405GP) || defined(CONFIG_405CR) || \
+#if (defined(CONFIG_405GP) || \
defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \
defined(CONFIG_405EX) || defined(CONFIG_405))
/*
#define ARRAY_SIZE(x) (sizeof(x) / sizeof((x)[0]))
-#if defined(CONFIG_405GP) || defined(CONFIG_405CR)
+#if defined(CONFIG_405GP)
void get_sys_info (PPC4xx_SYS_INFO * sysInfo)
{
{
ulong val;
-#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \
+#if defined(CONFIG_405GP) || \
defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \
defined(CONFIG_405EX) || defined(CONFIG_405) || \
defined(CONFIG_440)
#endif /* CONFIG_440 */
/*****************************************************************************/
-#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \
+#if defined(CONFIG_405GP) || \
defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \
defined(CONFIG_405EX) || defined(CONFIG_405)
/*----------------------------------------------------------------------- */
#endif /* CONFIG_NAND_SPL */
-#endif /* CONFIG_405GP || CONFIG_405CR || CONFIG_405 || CONFIG_405EP */
+#endif /* CONFIG_405GP || CONFIG_405 || CONFIG_405EP */
/*----------------------------------------------------------------------- */
+++ /dev/null
-/*
- * (C) Copyright 2010
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#ifndef _PPC405CR_H_
-#define _PPC405CR_H_
-
-#define CONFIG_SDRAM_PPC4xx_IBM_SDRAM /* IBM SDRAM controller */
-
-/* Memory mapped register */
-#define CONFIG_SYS_PERIPHERAL_BASE 0xef600000 /* Internal Peripherals */
-
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_PERIPHERAL_BASE + 0x0300)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_PERIPHERAL_BASE + 0x0400)
-
-#define GPIO0_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x0700)
-
-/* DCR's */
-#define DCP0_CFGADDR 0x0014 /* Decompression controller addr reg */
-#define DCP0_CFGDATA 0x0015 /* Decompression controller data reg */
-#define OCM0_ISCNTL 0x0019 /* OCM I-side control reg */
-#define OCM0_DSARC 0x001a /* OCM D-side address compare */
-#define OCM0_DSCNTL 0x001b /* OCM D-side control */
-#define CPC0_PLLMR 0x00b0 /* PLL mode register */
-#define CPC0_CR0 0x00b1 /* chip control register 0 */
-#define CPC0_CR1 0x00b2 /* chip control register 1 */
-#define CPC0_PSR 0x00b4 /* chip pin strapping reg */
-#define CPC0_EIRR 0x00b6 /* ext interrupt routing reg */
-#define CPC0_SR 0x00b8 /* Power management status */
-#define CPC0_ER 0x00b9 /* Power management enable */
-#define CPC0_FR 0x00ba /* Power management force */
-#define CPC0_ECR 0x00aa /* edge conditioner register */
-
-#define PLLMR_FWD_DIV_MASK 0xE0000000 /* Forward Divisor */
-#define PLLMR_FWD_DIV_BYPASS 0xE0000000
-#define PLLMR_FWD_DIV_3 0xA0000000
-#define PLLMR_FWD_DIV_4 0x80000000
-#define PLLMR_FWD_DIV_6 0x40000000
-
-#define PLLMR_FB_DIV_MASK 0x1E000000 /* Feedback Divisor */
-#define PLLMR_FB_DIV_1 0x02000000
-#define PLLMR_FB_DIV_2 0x04000000
-#define PLLMR_FB_DIV_3 0x06000000
-#define PLLMR_FB_DIV_4 0x08000000
-
-#define PLLMR_TUNING_MASK 0x01F80000
-
-#define PLLMR_CPU_TO_PLB_MASK 0x00060000 /* CPU:PLB Frequency Divisor */
-#define PLLMR_CPU_PLB_DIV_1 0x00000000
-#define PLLMR_CPU_PLB_DIV_2 0x00020000
-#define PLLMR_CPU_PLB_DIV_3 0x00040000
-#define PLLMR_CPU_PLB_DIV_4 0x00060000
-
-#define PLLMR_OPB_TO_PLB_MASK 0x00018000 /* OPB:PLB Frequency Divisor */
-#define PLLMR_OPB_PLB_DIV_1 0x00000000
-#define PLLMR_OPB_PLB_DIV_2 0x00008000
-#define PLLMR_OPB_PLB_DIV_3 0x00010000
-#define PLLMR_OPB_PLB_DIV_4 0x00018000
-
-#define PLLMR_PCI_TO_PLB_MASK 0x00006000 /* PCI:PLB Frequency Divisor */
-#define PLLMR_PCI_PLB_DIV_1 0x00000000
-#define PLLMR_PCI_PLB_DIV_2 0x00002000
-#define PLLMR_PCI_PLB_DIV_3 0x00004000
-#define PLLMR_PCI_PLB_DIV_4 0x00006000
-
-#define PLLMR_EXB_TO_PLB_MASK 0x00001800 /* External Bus:PLB Divisor */
-#define PLLMR_EXB_PLB_DIV_2 0x00000000
-#define PLLMR_EXB_PLB_DIV_3 0x00000800
-#define PLLMR_EXB_PLB_DIV_4 0x00001000
-#define PLLMR_EXB_PLB_DIV_5 0x00001800
-
-/* definitions for PPC405GPr (new mode strapping) */
-#define PLLMR_FWDB_DIV_MASK 0x00000007 /* Forward Divisor B */
-
-#define PSR_PLL_FWD_MASK 0xC0000000
-#define PSR_PLL_FDBACK_MASK 0x30000000
-#define PSR_PLL_TUNING_MASK 0x0E000000
-#define PSR_PLB_CPU_MASK 0x01800000
-#define PSR_OPB_PLB_MASK 0x00600000
-#define PSR_PCI_PLB_MASK 0x00180000
-#define PSR_EB_PLB_MASK 0x00060000
-#define PSR_ROM_WIDTH_MASK 0x00018000
-#define PSR_ROM_LOC 0x00004000
-#define PSR_PCI_ASYNC_EN 0x00001000
-#define PSR_PERCLK_SYNC_MODE_EN 0x00000800 /* PPC405GPr only */
-#define PSR_PCI_ARBIT_EN 0x00000400
-#define PSR_NEW_MODE_EN 0x00000020 /* PPC405GPr only */
-
-#endif /* _PPC405CR_H_ */
* Within this group there is a slight variation concerning the bit field
* position of the EMPL and EMPH fields:
*/
-#if defined(CONFIG_405CR) || defined(CONFIG_405GP) || \
+#if defined(CONFIG_405GP) || \
defined(CONFIG_405EP) || \
defined(CONFIG_440EP) || defined(CONFIG_440GR) || \
defined(CONFIG_440EPX) || defined(CONFIG_440GRX)
#define CONFIG_EBC_PPC4xx_IBM_VER1
-#if defined(CONFIG_405CR) || defined(CONFIG_405GP) || \
+#if defined(CONFIG_405GP) || \
defined(CONFIG_405EP)
#define EBC_CFG_EMPH_POS 8
#define EBC_CFG_EMPL_POS 6
/*
* Define the max number of EBC banks (chip selects)
*/
-#if defined(CONFIG_405CR) || defined(CONFIG_405GP) || \
+#if defined(CONFIG_405GP) || \
defined(CONFIG_405EZ) || \
defined(CONFIG_440GP) || defined(CONFIG_440GX)
#define EBC_NUM_BANKS 8
/*
* Include SoC specific headers
*/
-#if defined(CONFIG_405CR)
-#include <asm/ppc405cr.h>
-#endif
-
#if defined(CONFIG_405EP)
#include <asm/ppc405ep.h>
#endif
#define PVR_405GP_RC 0x40110082
#define PVR_405GP_RD 0x401100C4
#define PVR_405GP_RE 0x40110145 /* same as pc405cr rev c */
-#define PVR_405CR_RA 0x40110041
-#define PVR_405CR_RB 0x401100C5
-#define PVR_405CR_RC 0x40110145 /* same as pc405gp rev e */
#define PVR_405EP_RA 0x51210950
#define PVR_405GPR_RB 0x50910951
#define PVR_405EZ_RA 0x41511460
unsigned int bi_baudrate; /* Console Baudrate */
#if defined(CONFIG_405) || \
defined(CONFIG_405GP) || \
- defined(CONFIG_405CR) || \
defined(CONFIG_405EP) || \
defined(CONFIG_405EZ) || \
defined(CONFIG_405EX) || \
print_num("immr_base", bd->bi_immr_base);
#endif
print_num("bootflags", bd->bi_bootflags);
-#if defined(CONFIG_405CR) || defined(CONFIG_405EP) || \
+#if defined(CONFIG_405EP) || \
defined(CONFIG_405GP) || \
defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
defined(CONFIG_440GR) || defined(CONFIG_440GRX) || \
defined(CONFIG_440SPE) || defined(CONFIG_XILINX_405)
print_mhz("pci_busfreq", bd->bi_pci_busfreq);
#endif
-#else /* ! CONFIG_405GP, CONFIG_405CR, CONFIG_405EP, CONFIG_XILINX_405, CONFIG_440EP CONFIG_440GR */
+#else /* ! CONFIG_405GP, CONFIG_405EP, CONFIG_XILINX_405, CONFIG_440EP CONFIG_440GR */
#if defined(CONFIG_CPM2)
print_mhz("vco", bd->bi_vco);
print_mhz("sccfreq", bd->bi_sccfreq);
print_mhz("cpmfreq", bd->bi_cpmfreq);
#endif
print_mhz("busfreq", bd->bi_busfreq);
-#endif /* CONFIG_405GP, CONFIG_405CR, CONFIG_405EP, CONFIG_XILINX_405, CONFIG_440EP CONFIG_440GR */
+#endif /* CONFIG_405GP, CONFIG_405EP, CONFIG_XILINX_405, CONFIG_440EP CONFIG_440GR */
#ifdef CONFIG_ENABLE_36BIT_PHYS
#ifdef CONFIG_PHYS_64BIT
unsigned int bi_baudrate; /* Console Baudrate */
#if defined(CONFIG_405) || \
defined(CONFIG_405GP) || \
- defined(CONFIG_405CR) || \
defined(CONFIG_405EP) || \
defined(CONFIG_405EZ) || \
defined(CONFIG_405EX) || \
extern struct serial_device serial_scc_device;
extern struct serial_device *default_serial_console(void);
-#if defined(CONFIG_405GP) || defined(CONFIG_405CR) || \
+#if defined(CONFIG_405GP) || \
defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \
defined(CONFIG_405EX) || defined(CONFIG_440) || \
defined(CONFIG_MB86R0x) || defined(CONFIG_MPC5xxx) || \