--- /dev/null
+Submitted as http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=3984/1
+
+This patch fixes an error in the numbering of the disk LEDs on the
+Linksys NSLU2. The error crept in because the physical location
+of the LEDs has the Disk 2 LED *above* the Disk 1 LED.
+
+Thanks to Gordon Farquharson for reporting this.
+
+Signed-off-by: Rod Whitby <rod@whitby.id.au>
+
+PATCH FOLLOWS
+KernelVersion: 2.6.19
+
+Index: linux-2.6.19/include/asm-arm/arch-ixp4xx/nslu2.h
+===================================================================
+--- linux-2.6.19.orig/include/asm-arm/arch-ixp4xx/nslu2.h
++++ linux-2.6.19/include/asm-arm/arch-ixp4xx/nslu2.h
+@@ -76,6 +76,7 @@
+
+ #define NSLU2_GPIO_BUZZ 4
+ #define NSLU2_BZ_BM (1L << NSLU2_GPIO_BUZZ)
++
+ /* LEDs */
+
+ #define NSLU2_LED_RED NSLU2_GPIO0
+@@ -84,8 +85,8 @@
+ #define NSLU2_LED_RED_BM (1L << NSLU2_LED_RED)
+ #define NSLU2_LED_GRN_BM (1L << NSLU2_LED_GRN)
+
+-#define NSLU2_LED_DISK1 NSLU2_GPIO2
+-#define NSLU2_LED_DISK2 NSLU2_GPIO3
++#define NSLU2_LED_DISK1 NSLU2_GPIO3
++#define NSLU2_LED_DISK2 NSLU2_GPIO2
+
+ #define NSLU2_LED_DISK1_BM (1L << NSLU2_GPIO2)
+ #define NSLU2_LED_DISK2_BM (1L << NSLU2_GPIO3)
--- /dev/null
+Index: linux-2.6.19/include/asm-arm/arch-ixp4xx/platform.h
+===================================================================
+--- linux-2.6.19.orig/include/asm-arm/arch-ixp4xx/platform.h
++++ linux-2.6.19/include/asm-arm/arch-ixp4xx/platform.h
+@@ -100,6 +100,7 @@ struct mac_plat_info {
+ int phy_id; /* ID of the connected PHY (PCB/platform dependent) */
+ int rxq_id; /* Queue ID of the RX-free q*/
+ int txq_id; /* Where to push the outgoing packets */
++ unsigned char hwaddr[6]; /* Desired hardware address */
+ };
+
+
+Index: linux-2.6.19/drivers/net/ixp4xx/mac_driver.c
+===================================================================
+--- linux-2.6.19.orig/drivers/net/ixp4xx/mac_driver.c
++++ linux-2.6.19/drivers/net/ixp4xx/mac_driver.c
+@@ -189,6 +189,24 @@ static int ixmac_open (struct net_device
+ }
+ mac->rxq_pkt += RX_QUEUE_PREFILL;
+
++ /* printk(KERN_INFO "...Platform MAC=0x%02x%02x%02x%02x%02x%02x\n",
++ mac->plat->hwaddr[0],
++ mac->plat->hwaddr[1],
++ mac->plat->hwaddr[2],
++ mac->plat->hwaddr[3],
++ mac->plat->hwaddr[4],
++ mac->plat->hwaddr[5]
++ ); */
++ /* Only use platform or random if there's currently no device hw addr */
++ if (is_zero_ether_addr(dev->dev_addr)) {
++ if (is_zero_ether_addr(mac->plat->hwaddr)) {
++ random_ether_addr(dev->dev_addr);
++ dev->dev_addr[5] = mac->plat->phy_id;
++ }
++ else
++ memcpy(dev->dev_addr, mac->plat->hwaddr, 6);
++ }
++
+ mac_init(mac);
+ npe_mh_set_rxqid(npe, mac->plat, RX_DONE_QID);
+ mac_set_uniaddr(dev);
+@@ -434,9 +452,15 @@ static int mac_probe(struct platform_dev
+ * following commands:
+ * "ip link set address 02:03:04:04:04:01 dev eth0"
+ * "ifconfig eth0 hw ether 02:03:04:04:04:07"
+- */
+- random_ether_addr(dev->dev_addr);
+- dev->dev_addr[5] = plat->phy_id;
++ */
++/* Note: moved to ixmac_open to allow notifiers to run for compiled in modules
++ if (is_zero_ether_addr(plat->hwaddr)) {
++ random_ether_addr(dev->dev_addr);
++ dev->dev_addr[5] = plat->phy_id;
++ }
++ else
++ memcpy(dev->dev_addr, plat->hwaddr, 6);
++*/
+
+ printk(KERN_INFO IXMAC_NAME " driver " IXMAC_VERSION
+ ": %s on %s with PHY[%d] initialized\n",
--- /dev/null
+Index: linux-2.6.19/drivers/net/ixp4xx/Kconfig
+===================================================================
+--- linux-2.6.19.orig/drivers/net/ixp4xx/Kconfig
++++ linux-2.6.19/drivers/net/ixp4xx/Kconfig
+@@ -11,6 +11,7 @@ config IXP4XX_NPE
+ tristate "IXP4xx NPE support"
+ depends on ARCH_IXP4XX
+ depends on NET_ETHERNET
++ select CRC16
+ help
+ The IXP4XX NPE driver supports the 3 CPU co-processors called
+ "Network Processing Engines" (NPE). It adds support fo downloading
+@@ -18,7 +19,7 @@ config IXP4XX_NPE
+ More about this at: Documentation/networking/ixp4xx/README.
+ You can either use this OR the Intel Access Library (IAL)
+
+-config IXP4XX_FW_LOAD
++config IXP4XX_NPE_FW_LOAD
+ bool "Use Firmware hotplug for Microcode download"
+ depends on IXP4XX_NPE
+ select HOTPLUG
+@@ -28,6 +29,13 @@ config IXP4XX_FW_LOAD
+ /usr/lib/hotplug/firmware/NPE-[ABC]
+ see Documentation/firmware_class/hotplug-script
+
++config IXP4XX_NPE_FW_MTD
++ bool "Load firmware from an mtd partition"
++ depends on IXP4XX_NPE && MTD_IXP4XX
++ help
++ With this option, the driver will search for
++ the firmware into an MTD partition.
++
+ config IXP4XX_MAC
+ tristate "IXP4xx MAC support"
+ depends on IXP4XX_NPE
+Index: linux-2.6.19/drivers/net/ixp4xx/Makefile
+===================================================================
+--- linux-2.6.19.orig/drivers/net/ixp4xx/Makefile
++++ linux-2.6.19/drivers/net/ixp4xx/Makefile
+@@ -1,6 +1,7 @@
+ obj-$(CONFIG_IXP4XX_QMGR) += ixp4xx_qmgr.o
+ obj-$(CONFIG_IXP4XX_NPE) += ixp4xx_npe.o
+ obj-$(CONFIG_IXP4XX_MAC) += ixp4xx_mac.o
++obj-$(CONFIG_IXP4XX_NPE_FW_MTD) += npe_ucode.o
+
+ ixp4xx_npe-objs := ucode_dl.o npe_mh.o
+ ixp4xx_mac-objs := mac_driver.o qmgr_eth.o phy.o
+Index: linux-2.6.19/drivers/net/ixp4xx/npe_ucode.c
+===================================================================
+--- /dev/null
++++ linux-2.6.19/drivers/net/ixp4xx/npe_ucode.c
+@@ -0,0 +1,185 @@
++/*
++ * Provide an NPE platform device for microcode handling
++ *
++ * Copyright (C) 2006 Christian Hohnstaedt <chohnstaedt@innominate.com>
++ *
++ * This file is released under the GPLv2
++ */
++
++#include <linux/kernel.h>
++#include <linux/platform_device.h>
++#include <linux/init.h>
++#include <linux/slab.h>
++#include <linux/firmware.h>
++#include <linux/mtd/mtd.h>
++
++#include <linux/ixp_npe.h>
++
++#define DL_MAGIC 0xfeedf00d
++#define DL_MAGIC_SWAP 0x0df0edfe
++
++#define IMG_SIZE(image) (((image)->size * sizeof(u32)) + \
++ sizeof(struct dl_image))
++
++#define IMG_REV_MAJOR(id) (((id) >> 8) & 0x0f)
++#define IMG_REV_MINOR(id) ((id) & 0x0f)
++#define IMG_FUNC(id) (((id) >> 16) & 0xff)
++#define IMG_NPE(id) (((id) >> 24) & 0x0f)
++#define IMG_IXP(id) (((id) >> 28) & 0x0f)
++
++static struct platform_driver ixp4xx_npe_ucode_driver;
++static unsigned char *partition_name = NULL;
++
++static void print_image_info(u32 id, u32 offset, u32 size)
++{
++ unsigned char idx;
++ const char *names[] = { "IXP425", "IXP465", "unknown" };
++
++ idx = IMG_IXP(id) < 2 ? IMG_IXP(id) : 2;
++
++ printk(KERN_INFO "npe: found at 0x%x, %s/NPE-%c func: %02x, rev: %x.%x, "
++ "size: %5d, id: %08x\n", offset, names[idx], IMG_NPE(id) + 'A',
++ IMG_FUNC(id), IMG_REV_MAJOR(id), IMG_REV_MINOR(id), size, id);
++}
++
++void npe_swap_image(struct dl_image *image)
++{
++ unsigned int i;
++
++ image->magic = swab32(image->magic);
++ image->id = swab32(image->id);
++ image->size = swab32(image->size);
++
++ for (i = 0; i < image->size; i++)
++ image->u.data[i] = swab32(image->u.data[i]);
++}
++
++static void npe_find_microcode(struct mtd_info *mtd)
++{
++ u32 buf;
++ u32 magic = htonl(DL_MAGIC);
++ u32 id, size;
++ size_t retlen;
++ int err;
++ unsigned int offset = 0;
++
++ printk("npe: searching for firmware...\n");
++
++ while (offset < mtd->size) {
++
++ err = mtd->read(mtd, offset, 4, &retlen, (u_char *) &buf);
++ offset += retlen;
++
++ if (buf != magic)
++ continue;
++
++ err = mtd->read(mtd, offset, 4, &retlen, (u_char *) &id);
++ offset += retlen;
++
++ if (id == magic)
++ break;
++
++ id = ntohl(id);
++
++ err = mtd->read(mtd, offset, 4, &retlen, (u_char *) &size);
++ offset += retlen;
++
++ size = (ntohl(size) * 4) + 12;
++
++ print_image_info(id, offset - 12, size);
++
++ if (size < 24000 && ( IMG_FUNC(id) == 0x01 || IMG_FUNC(id) == 0x00) ) { // XXX fix size/detection
++
++ struct dl_image *image = kmalloc(size, GFP_KERNEL);
++
++ /* we are going to load it, rewind offset */
++ offset -= 12;
++
++ if (image) {
++ err = mtd->read(mtd, offset, size, &retlen, (u_char *) image);
++
++ if (err == 0 && retlen == size) {
++ if (image->magic == DL_MAGIC_SWAP)
++ npe_swap_image(image);
++
++ store_npe_image(image, NULL);
++ } else {
++ printk(KERN_ERR "unable to read firmware\n");
++ }
++
++ kfree(image);
++ }
++
++ offset += size;
++ }
++ }
++}
++
++static void npe_flash_add(struct mtd_info *mtd)
++{
++ if (partition_name == NULL)
++ return;
++
++ if (strcmp(mtd->name, partition_name) == 0) {
++ npe_find_microcode(mtd);
++ }
++}
++
++static void npe_flash_remove(struct mtd_info *mtd) {
++}
++
++static struct mtd_notifier npe_flash_notifier = {
++ .add = npe_flash_add,
++ .remove = npe_flash_remove,
++};
++
++static int npe_ucode_probe(struct platform_device *pdev)
++{
++ struct npe_ucode_platform_data *data = pdev->dev.platform_data;
++
++ if (partition_name)
++ return -EEXIST;
++
++ if (data && data->mtd_partition) {
++ partition_name = data->mtd_partition;
++ return 0;
++ }
++
++ return -EINVAL;
++}
++
++static int npe_ucode_remove(struct platform_device *pdev)
++{
++ return 0;
++}
++
++static struct platform_driver ixp4xx_npe_ucode_driver = {
++ .driver = {
++ .name = "ixp4xx_npe_ucode",
++ .owner = THIS_MODULE,
++ },
++ .probe = npe_ucode_probe,
++ .remove = npe_ucode_remove,
++};
++
++static int __init npe_ucode_init(void)
++{
++ int ret;
++
++ ret = platform_driver_register(&ixp4xx_npe_ucode_driver);
++ register_mtd_user(&npe_flash_notifier);
++
++ return ret;
++}
++
++static void __exit npe_ucode_exit(void)
++{
++ unregister_mtd_user(&npe_flash_notifier);
++ platform_driver_unregister(&ixp4xx_npe_ucode_driver);
++}
++
++module_init(npe_ucode_init);
++module_exit(npe_ucode_exit);
++
++MODULE_LICENSE("GPL");
++MODULE_AUTHOR("Alessandro Zummo <a.zummo@towertech.it>");
+Index: linux-2.6.19/drivers/net/ixp4xx/ucode_dl.c
+===================================================================
+--- linux-2.6.19.orig/drivers/net/ixp4xx/ucode_dl.c
++++ linux-2.6.19/drivers/net/ixp4xx/ucode_dl.c
+@@ -16,6 +16,7 @@
+ #include <linux/firmware.h>
+ #include <linux/dma-mapping.h>
+ #include <linux/byteorder/swab.h>
++#include <linux/crc16.h>
+ #include <asm/uaccess.h>
+ #include <asm/io.h>
+
+@@ -30,6 +31,12 @@
+ #define IMG_SIZE(image) (((image)->size * sizeof(u32)) + \
+ sizeof(struct dl_image))
+
++#define IMG_REV_MAJOR(id) (((id) >> 8) & 0x0f)
++#define IMG_REV_MINOR(id) ((id) & 0x0f)
++#define IMG_FUNC(id) (((id) >> 16) & 0xff)
++#define IMG_NPE(id) (((id) >> 24) & 0x0f)
++#define IMG_IXP(id) (((id) >> 28) & 0x0f)
++
+ #define BT_INSTR 0
+ #define BT_DATA 1
+
+@@ -38,21 +45,6 @@ enum blk_type {
+ data,
+ };
+
+-struct dl_block {
+- u32 type;
+- u32 offset;
+-};
+-
+-struct dl_image {
+- u32 magic;
+- u32 id;
+- u32 size;
+- union {
+- u32 data[0];
+- struct dl_block block[0];
+- } u;
+-};
+-
+ struct dl_codeblock {
+ u32 npe_addr;
+ u32 size;
+@@ -134,23 +126,41 @@ struct device *get_npe_by_id(int id)
+ &id, match_by_npeid);
+ }
+
+-static int store_npe_image(struct dl_image *image, struct device *dev)
++int store_npe_image(struct dl_image *image, struct device *dev)
+ {
+ struct dl_block *blk;
+ struct dl_codeblock *cb;
+ struct npe_info *npe;
+- int ret=0;
++ int ret = 0;
++ u16 crc;
+
+ if (!dev) {
+- dev = get_npe_by_id( (image->id >> 24) & 0xf);
+- put_device(dev);
++ dev = get_npe_by_id(IMG_NPE(image->id));
++ if (dev)
++ put_device(dev);
++ // XXX shouldn't this put_device be outside if(!dev) ?
++ else
++ printk(KERN_ERR "npe: cannot find npe for image %x\n", IMG_NPE(image->id));
+ }
++
+ if (!dev)
+ return -ENODEV;
+
++ if (image->size > 24000) { // XXX fix max size
++ printk(KERN_ERR "npe: firmware too large\n");
++ return -EFBIG;
++ }
++
++ if (IMG_REV_MAJOR(image->id) != 2) {
++ printk(KERN_ERR "npe: only revision 2 is supported at this time\n");
++ return -EINVAL;
++ }
++
++ crc = crc16(0, (u8 *) image, IMG_SIZE(image));
++
+ npe = dev_get_drvdata(dev);
+
+- if ( npe_status(npe) & IX_NPEDL_EXCTL_STATUS_RUN) {
++ if (npe_status(npe) & IX_NPEDL_EXCTL_STATUS_RUN) {
+ printk(KERN_INFO "Cowardly refusing to reload an Image "
+ "into the running %s\n", npe->plat->name);
+ return 0; /* indicate success anyway... */
+@@ -173,9 +183,9 @@ static int store_npe_image(struct dl_ima
+ *(u32*)npe->img_info = cpu_to_be32(image->id);
+ npe_start(npe);
+
+- printk(KERN_INFO "Image loaded to %s Func:%x, Rel: %x:%x, Status: %x\n",
++ printk(KERN_INFO "npe: firmware loaded to %s, func: %02x, rev: %x.%x, status: %x, crc: %x\n",
+ npe->plat->name, npe->img_info[1], npe->img_info[2],
+- npe->img_info[3], npe_status(npe));
++ npe->img_info[3], npe_status(npe), crc);
+ return 0;
+ }
+
+@@ -265,8 +275,7 @@ static ssize_t ucode_write(struct file *
+
+ static void npe_firmware_probe(struct device *dev)
+ {
+-#if (defined(CONFIG_FW_LOADER) || defined(CONFIG_FW_LOADER_MODULE)) \
+- && defined(MODULE)
++#ifdef CONFIG_IXP4XX_NPE_FW_LOADER
+ const struct firmware *fw_entry;
+ struct npe_info *npe = dev_get_drvdata(dev);
+ struct dl_image *image;
+@@ -388,7 +397,7 @@ static int npe_probe(struct platform_dev
+
+ npe->plat = plat;
+ disable_npe_irq(npe);
+- if (! (npe_status(npe) & IX_NPEDL_EXCTL_STATUS_RUN))
++ if (!(npe_status(npe) & IX_NPEDL_EXCTL_STATUS_RUN))
+ npe_firmware_probe(&pdev->dev);
+
+ return 0;
+@@ -464,3 +473,4 @@ MODULE_LICENSE("GPL");
+ MODULE_AUTHOR("Christian Hohnstaedt <chohnstaedt@innominate.com>");
+
+ EXPORT_SYMBOL(get_npe_by_id);
++EXPORT_SYMBOL(store_npe_image);
+Index: linux-2.6.19/include/asm-arm/arch-ixp4xx/platform.h
+===================================================================
+--- linux-2.6.19.orig/include/asm-arm/arch-ixp4xx/platform.h
++++ linux-2.6.19/include/asm-arm/arch-ixp4xx/platform.h
+@@ -86,6 +86,20 @@ struct ixp4xx_i2c_pins {
+ unsigned long scl_pin;
+ };
+
++struct dl_block {
++ u32 type;
++ u32 offset;
++};
++
++struct dl_image {
++ u32 magic;
++ u32 id;
++ u32 size;
++ union {
++ u32 data[0];
++ struct dl_block block[0];
++ } u;
++};
+ struct npe_plat_data {
+ const char *name;
+ int data_size;
+@@ -103,6 +117,9 @@ struct mac_plat_info {
+ unsigned char hwaddr[6]; /* Desired hardware address */
+ };
+
++struct npe_ucode_platform_data {
++ unsigned char *mtd_partition;
++};
+
+ struct sys_timer;
+
+Index: linux-2.6.19/include/linux/ixp_npe.h
+===================================================================
+--- linux-2.6.19.orig/include/linux/ixp_npe.h
++++ linux-2.6.19/include/linux/ixp_npe.h
+@@ -71,6 +71,7 @@ static inline u32 npe_read_ecs_reg(struc
+ }
+
+ extern struct device *get_npe_by_id(int id);
++extern int store_npe_image(struct dl_image *image, struct device *dev);
+
+ /* NPE Messages */
+ extern int
--- /dev/null
+Index: linux-2.6.19/arch/arm/mach-ixp4xx/nslu2-setup.c
+===================================================================
+--- linux-2.6.19.orig/arch/arm/mach-ixp4xx/nslu2-setup.c
++++ linux-2.6.19/arch/arm/mach-ixp4xx/nslu2-setup.c
+@@ -137,6 +137,28 @@ static struct platform_device nslu2_uart
+ .resource = nslu2_uart_resources,
+ };
+
++static struct resource res_mac0 = {
++ .start = IXP4XX_EthB_BASE_PHYS,
++ .end = IXP4XX_EthB_BASE_PHYS + 0x1ff,
++ .flags = IORESOURCE_MEM,
++};
++
++static struct mac_plat_info plat_mac0 = {
++ .npe_id = 1,
++ .phy_id = 1,
++ .eth_id = 0,
++ .rxq_id = 27,
++ .txq_id = 24,
++};
++
++static struct platform_device mac0 = {
++ .name = "ixp4xx_mac",
++ .id = 0,
++ .dev.platform_data = &plat_mac0,
++ .num_resources = 1,
++ .resource = &res_mac0,
++};
++
+ static struct platform_device *nslu2_devices[] __initdata = {
+ &nslu2_i2c_controller,
+ &nslu2_flash,
+@@ -144,6 +166,7 @@ static struct platform_device *nslu2_dev
+ #ifdef CONFIG_LEDS_IXP4XX
+ &nslu2_leds,
+ #endif
++ &mac0
+ };
+
+ static void nslu2_power_off(void)
--- /dev/null
+Index: linux-2.6.19/arch/arm/mach-ixp4xx/nas100d-setup.c
+===================================================================
+--- linux-2.6.19.orig/arch/arm/mach-ixp4xx/nas100d-setup.c
++++ linux-2.6.19/arch/arm/mach-ixp4xx/nas100d-setup.c
+@@ -123,12 +123,35 @@ static struct platform_device nas100d_ua
+ .resource = nas100d_uart_resources,
+ };
+
++static struct resource res_mac0 = {
++ .start = IXP4XX_EthB_BASE_PHYS,
++ .end = IXP4XX_EthB_BASE_PHYS + 0x1ff,
++ .flags = IORESOURCE_MEM,
++};
++
++static struct mac_plat_info plat_mac0 = {
++ .npe_id = 1,
++ .phy_id = 0,
++ .eth_id = 0,
++ .rxq_id = 27,
++ .txq_id = 24,
++};
++
++static struct platform_device mac0 = {
++ .name = "ixp4xx_mac",
++ .id = 0,
++ .dev.platform_data = &plat_mac0,
++ .num_resources = 1,
++ .resource = &res_mac0,
++};
++
+ static struct platform_device *nas100d_devices[] __initdata = {
+ &nas100d_i2c_controller,
+ &nas100d_flash,
+ #ifdef CONFIG_LEDS_IXP4XX
+ &nas100d_leds,
+ #endif
++ &mac0
+ };
+
+ static void nas100d_power_off(void)
--- /dev/null
+---
+ arch/arm/mach-ixp4xx/nslu2-setup.c | 13 ++++++++++++-
+ 1 file changed, 12 insertions(+), 1 deletion(-)
+
+Index: linux-2.6.19/arch/arm/mach-ixp4xx/nslu2-setup.c
+===================================================================
+--- linux-2.6.19.orig/arch/arm/mach-ixp4xx/nslu2-setup.c
++++ linux-2.6.19/arch/arm/mach-ixp4xx/nslu2-setup.c
+@@ -159,6 +159,16 @@ static struct platform_device mac0 = {
+ .resource = &res_mac0,
+ };
+
++struct npe_ucode_platform_data nslu2_npe_ucode_data = {
++ .mtd_partition = "FIS directory",
++};
++
++static struct platform_device nslu2_npe_ucode = {
++ .name = "ixp4xx_npe_ucode",
++ .id = 0,
++ .dev.platform_data = &nslu2_npe_ucode_data,
++};
++
+ static struct platform_device *nslu2_devices[] __initdata = {
+ &nslu2_i2c_controller,
+ &nslu2_flash,
+@@ -166,7 +176,8 @@ static struct platform_device *nslu2_dev
+ #ifdef CONFIG_LEDS_IXP4XX
+ &nslu2_leds,
+ #endif
+- &mac0
++ &mac0,
++ &nslu2_npe_ucode,
+ };
+
+ static void nslu2_power_off(void)
--- /dev/null
+---
+ arch/arm/mach-ixp4xx/nas100d-setup.c | 13 ++++++++++++-
+ 1 file changed, 12 insertions(+), 1 deletion(-)
+
+Index: linux-2.6.19/arch/arm/mach-ixp4xx/nas100d-setup.c
+===================================================================
+--- linux-2.6.19.orig/arch/arm/mach-ixp4xx/nas100d-setup.c
++++ linux-2.6.19/arch/arm/mach-ixp4xx/nas100d-setup.c
+@@ -145,13 +145,24 @@ static struct platform_device mac0 = {
+ .resource = &res_mac0,
+ };
+
++struct npe_ucode_platform_data nas100d_npe_ucode_data = {
++ .mtd_partition = "sysconfig",
++};
++
++static struct platform_device nas100d_npe_ucode = {
++ .name = "ixp4xx_npe_ucode",
++ .id = 0,
++ .dev.platform_data = &nas100d_npe_ucode_data,
++};
++
+ static struct platform_device *nas100d_devices[] __initdata = {
+ &nas100d_i2c_controller,
+ &nas100d_flash,
+ #ifdef CONFIG_LEDS_IXP4XX
+ &nas100d_leds,
+ #endif
+- &mac0
++ &mac0,
++ &nas100d_npe_ucode,
+ };
+
+ static void nas100d_power_off(void)
--- /dev/null
+---
+ arch/arm/mach-ixp4xx/nas100d-setup.c | 27 +++++++++++++++++++++++++++
+ 1 file changed, 27 insertions(+)
+
+Index: linux-2.6.19/arch/arm/mach-ixp4xx/nas100d-setup.c
+===================================================================
+--- linux-2.6.19.orig/arch/arm/mach-ixp4xx/nas100d-setup.c
++++ linux-2.6.19/arch/arm/mach-ixp4xx/nas100d-setup.c
+@@ -16,6 +16,7 @@
+ #include <linux/serial.h>
+ #include <linux/serial_8250.h>
+ #include <linux/leds.h>
++#include <linux/mtd/mtd.h>
+
+ #include <asm/mach-types.h>
+ #include <asm/mach/arch.h>
+@@ -165,6 +166,30 @@ static struct platform_device *nas100d_d
+ &nas100d_npe_ucode,
+ };
+
++static void nas100d_flash_add(struct mtd_info *mtd)
++{
++ if (strcmp(mtd->name, "RedBoot config") == 0) {
++ size_t retlen;
++ u_char mac[6];
++
++ if (mtd->read(mtd, 0x0FD8, 6, &retlen, mac) == 0 && retlen == 6) {
++ printk(KERN_INFO "nas100d mac: %.2x:%.2x:%.2x:%.2x:%.2x:%.2x\n",
++ mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
++ memcpy(plat_mac0.hwaddr, mac, 6);
++ } else {
++ printk(KERN_ERR "nas100d mac: read failed\n");
++ }
++ }
++}
++
++static void nas100d_flash_remove(struct mtd_info *mtd) {
++}
++
++static struct mtd_notifier nas100d_flash_notifier = {
++ .add = nas100d_flash_add,
++ .remove = nas100d_flash_remove,
++};
++
+ static void nas100d_power_off(void)
+ {
+ /* This causes the box to drop the power and go dead. */
+@@ -196,6 +221,8 @@ static void __init nas100d_init(void)
+ (void)platform_device_register(&nas100d_uart);
+
+ platform_add_devices(nas100d_devices, ARRAY_SIZE(nas100d_devices));
++
++ register_mtd_user(&nas100d_flash_notifier);
+ }
+
+ MACHINE_START(NAS100D, "Iomega NAS 100d")
--- /dev/null
+---
+ arch/arm/mach-ixp4xx/nslu2-setup.c | 27 +++++++++++++++++++++++++++
+ 1 file changed, 27 insertions(+)
+
+Index: linux-2.6.19/arch/arm/mach-ixp4xx/nslu2-setup.c
+===================================================================
+--- linux-2.6.19.orig/arch/arm/mach-ixp4xx/nslu2-setup.c
++++ linux-2.6.19/arch/arm/mach-ixp4xx/nslu2-setup.c
+@@ -18,6 +18,7 @@
+ #include <linux/serial.h>
+ #include <linux/serial_8250.h>
+ #include <linux/leds.h>
++#include <linux/mtd/mtd.h>
+
+ #include <asm/mach-types.h>
+ #include <asm/mach/arch.h>
+@@ -180,6 +181,30 @@ static struct platform_device *nslu2_dev
+ &nslu2_npe_ucode,
+ };
+
++static void nslu2_flash_add(struct mtd_info *mtd)
++{
++ if (strcmp(mtd->name, "RedBoot") == 0) {
++ size_t retlen;
++ u_char mac[6];
++
++ if (mtd->read(mtd, 0x3FFB0, 6, &retlen, mac) == 0 && retlen == 6) {
++ printk(KERN_INFO "nslu2 mac: %.2x:%.2x:%.2x:%.2x:%.2x:%.2x\n",
++ mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
++ memcpy(plat_mac0.hwaddr, mac, 6);
++ } else {
++ printk(KERN_ERR "nslu2 mac: read failed\n");
++ }
++ }
++}
++
++static void nslu2_flash_remove(struct mtd_info *mtd) {
++}
++
++static struct mtd_notifier nslu2_flash_notifier = {
++ .add = nslu2_flash_add,
++ .remove = nslu2_flash_remove,
++};
++
+ static void nslu2_power_off(void)
+ {
+ /* This causes the box to drop the power and go dead. */
+@@ -210,6 +235,8 @@ static void __init nslu2_init(void)
+ (void)platform_device_register(&nslu2_uart);
+
+ platform_add_devices(nslu2_devices, ARRAY_SIZE(nslu2_devices));
++
++ register_mtd_user(&nslu2_flash_notifier);
+ }
+
+ MACHINE_START(NSLU2, "Linksys NSLU2")
--- /dev/null
+From: Alan Cox <alan@redhat.com>
+To: Alessandro Zummo <alessandro.zummo@towertech.it>
+Cc: Jeff Garzik <jgarzik@redhat.com>, Alan Cox <alan@redhat.com>
+Subject: Re: drivers/ata/pata_artop.c
+Date: Sun, 15 Oct 2006 14:25:16 -0400
+User-Agent: Mutt/1.4.1i
+
+On Sun, Oct 15, 2006 at 07:18:31PM +0200, Alessandro Zummo wrote:
+> In the discovery phase there's a lot of time spent in the detection
+> of the second port.
+
+The error recovery is a bit determined right now - Tejun's been doing some
+work on SRST behaviour and also for the worst cases polled detect so it
+should come out ok
+
+> What's the correct way to inform the driver
+> to avoid checking the second port?
+
+Set the number of ports to 1 in your own tree for now. The real fix is
+not to go poking at pata ports if the ret is 0xFF
+
+---
+ drivers/ata/pata_artop.c | 6 ++++++
+ 1 file changed, 6 insertions(+)
+
+Index: linux-2.6.19/drivers/ata/pata_artop.c
+===================================================================
+--- linux-2.6.19.orig/drivers/ata/pata_artop.c
++++ linux-2.6.19/drivers/ata/pata_artop.c
+@@ -26,6 +26,7 @@
+ #include <scsi/scsi_host.h>
+ #include <linux/libata.h>
+ #include <linux/ata.h>
++#include <asm/mach-types.h>
+
+ #define DRV_NAME "pata_artop"
+ #define DRV_VERSION "0.4.2"
+@@ -469,6 +470,11 @@ static int artop_init_one (struct pci_de
+ pci_read_config_byte(pdev, 0x4a, ®);
+ pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80);
+
++ /* NAS100D workaround */
++#ifdef CONFIG_MACH_NAS100D
++ if (machine_is_nas100d())
++ ports = 1;
++#endif
+ }
+
+ BUG_ON(info == NULL);
--- /dev/null
+Index: linux-2.6.19/arch/arm/mach-ixp4xx/nslu2-setup.c
+===================================================================
+--- linux-2.6.19.orig/arch/arm/mach-ixp4xx/nslu2-setup.c
++++ linux-2.6.19/arch/arm/mach-ixp4xx/nslu2-setup.c
+@@ -20,6 +20,7 @@
+ #include <linux/leds.h>
+ #include <linux/mtd/mtd.h>
+
++#include <asm/setup.h>
+ #include <asm/mach-types.h>
+ #include <asm/mach/arch.h>
+ #include <asm/mach/flash.h>
+@@ -239,11 +240,41 @@ static void __init nslu2_init(void)
+ register_mtd_user(&nslu2_flash_notifier);
+ }
+
++static char nslu2_rtc_probe[] __initdata = "rtc-x1205.probe=0,0x6f ";
++
++static void __init nslu2_fixup(struct machine_desc *desc,
++ struct tag *tags, char **cmdline, struct meminfo *mi)
++{
++ struct tag *t = tags;
++ char *p = *cmdline;
++
++ /* Find the end of the tags table, taking note of any cmdline tag. */
++ for (; t->hdr.size; t = tag_next(t)) {
++ if (t->hdr.tag == ATAG_CMDLINE) {
++ p = t->u.cmdline.cmdline;
++ }
++ }
++
++ /* Overwrite the end of the table with a new cmdline tag. */
++ t->hdr.tag = ATAG_CMDLINE;
++ t->hdr.size = (sizeof (struct tag_header) +
++ strlen(nslu2_rtc_probe) + strlen(p) + 1 + 4) >> 2;
++ strlcpy(t->u.cmdline.cmdline, nslu2_rtc_probe, COMMAND_LINE_SIZE);
++ strlcpy(t->u.cmdline.cmdline + strlen(nslu2_rtc_probe), p,
++ COMMAND_LINE_SIZE - strlen(nslu2_rtc_probe));
++
++ /* Terminate the table. */
++ t = tag_next(t);
++ t->hdr.tag = ATAG_NONE;
++ t->hdr.size = 0;
++}
++
+ MACHINE_START(NSLU2, "Linksys NSLU2")
+ /* Maintainer: www.nslu2-linux.org */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
+ .boot_params = 0x00000100,
++ .fixup = nslu2_fixup,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
--- /dev/null
+Index: linux-2.6.19/arch/arm/mach-ixp4xx/nas100d-setup.c
+===================================================================
+--- linux-2.6.19.orig/arch/arm/mach-ixp4xx/nas100d-setup.c
++++ linux-2.6.19/arch/arm/mach-ixp4xx/nas100d-setup.c
+@@ -18,6 +18,7 @@
+ #include <linux/leds.h>
+ #include <linux/mtd/mtd.h>
+
++#include <asm/setup.h>
+ #include <asm/mach-types.h>
+ #include <asm/mach/arch.h>
+ #include <asm/mach/flash.h>
+@@ -225,11 +226,42 @@ static void __init nas100d_init(void)
+ register_mtd_user(&nas100d_flash_notifier);
+ }
+
++static char nas100d_rtc_probe[] __initdata = "rtc-pcf8563.probe=0,0x51 ";
++
++static void __init nas100d_fixup(struct machine_desc *desc,
++ struct tag *tags, char **cmdline, struct meminfo *mi)
++{
++ struct tag *t = tags;
++ char *p = *cmdline;
++
++ /* Find the end of the tags table, taking note of any cmdline tag. */
++ for (; t->hdr.size; t = tag_next(t)) {
++ if (t->hdr.tag == ATAG_CMDLINE) {
++ p = t->u.cmdline.cmdline;
++ }
++ }
++
++ /* Overwrite the end of the table with a new cmdline tag. */
++ t->hdr.tag = ATAG_CMDLINE;
++ t->hdr.size =
++ (sizeof (struct tag_header) +
++ strlen(nas100d_rtc_probe) + strlen(p) + 1 + 4) >> 2;
++ strlcpy(t->u.cmdline.cmdline, nas100d_rtc_probe, COMMAND_LINE_SIZE);
++ strlcpy(t->u.cmdline.cmdline + strlen(nas100d_rtc_probe), p,
++ COMMAND_LINE_SIZE - strlen(nas100d_rtc_probe));
++
++ /* Terminate the table. */
++ t = tag_next(t);
++ t->hdr.tag = ATAG_NONE;
++ t->hdr.size = 0;
++}
++
+ MACHINE_START(NAS100D, "Iomega NAS 100d")
+ /* Maintainer: www.nslu2-linux.org */
+ .phys_io = IXP4XX_PERIPHERAL_BASE_PHYS,
+ .io_pg_offst = ((IXP4XX_PERIPHERAL_BASE_VIRT) >> 18) & 0xFFFC,
+ .boot_params = 0x00000100,
++ .fixup = nas100d_fixup,
+ .map_io = ixp4xx_map_io,
+ .init_irq = ixp4xx_init_irq,
+ .timer = &ixp4xx_timer,
projects / openwrt / openwrt.git / commitdiff