ramips: add support for ELECOM WRH-300CR

ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB
DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but
easy-to-access) UART.

it also has internal USB hub and USB card reader which provide one USB
port, one SD card slot, and one microSD card slot.

Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com>
Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com>
SVN-Revision: 49211

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 2f40955d11047382d52a47376a5502c5b00f6279..e3b8500d373bc91a6aa1caed4bdb4aa81fc09ea3 100755 (executable)
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -265,6 +265,10 @@ whr-600d)
 wnce2001)
        set_wifi_led "$board:green:wlan"
        ;;
+wrh-300cr)
+       set_wifi_led "$board:green:wlan"
+       ucidef_set_led_netdev "lan" "lan" "$board:green:ethernet" "eth0"
+       ;;
 wt3020)
        ucidef_set_led_default "power" "power" "$board:blue:power" "0"
        ;;

diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index 4b65d36b985e1a6ce0b47e49eac2ecd809817f77..2863b8843f6030ed6b788de703c19ad13e38fad2 100755 (executable)
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -162,7 +162,8 @@ ramips_setup_interfaces()
        d105|\
        hpm|\
        na930|\
-       wli-tx4-ag300n)
+       wli-tx4-ag300n|\
+       wrh-300cr)
                ucidef_set_interface_lan "eth0"
                ;;
        e1700|\

diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh
index a2c965d79dc59ebe1f1c079862a3cf49d0acfda6..44353b6cc8c7746823edc230780a865b540765f1 100644 (file)
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -74,7 +74,8 @@ get_status_led() {
                status_led="$board:green:run"
                ;;
        awapn2403|\
-       dir-645)
+       dir-645|\
+       wrh-300cr)
                status_led="$board:green:wps"
                ;;
        cf-wr800n|\

diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
index 5f1df7b83ff496bfed937ea2117a1ee1294f8605..459de6f84dc70c2e9081d1c5dcb87004efd0b995 100755 (executable)
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -460,6 +460,9 @@ ramips_board_detect() {
        *"WR6202")
                name="wr6202"
                ;;
+       *"WRH-300CR")
+               name="wrh-300cr"
+               ;;
        *"WRTNODE")
                name="wrtnode"
                ;;

diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index cbeda7accbb36e3cf202f903771982777b5c0652..e880f60f7361bb814d1a55b324e6907e48cc4bc5 100755 (executable)
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -136,6 +136,7 @@ platform_check_image() {
        wnce2001|\
        wr512-3gn|\
        wr6202|\
+       wrh-300cr|\
        wrtnode|\
        wrtnode2r |\
        wrtnode2p |\

diff --git a/target/linux/ramips/dts/WRH-300CR.dts b/target/linux/ramips/dts/WRH-300CR.dts
new file mode 100644 (file)
index 0000000..79962e9
--- /dev/null
+++ b/target/linux/ramips/dts/WRH-300CR.dts
@@ -0,0 +1,127 @@
+/dts-v1/;
+
+/include/ "mt7620n.dtsi"
+
+/ {
+       compatible = "elecom,wrh-300cr", "ralink,mt7620n-soc";
+       model = "ELECOM WRH-300CR";
+
+       palmbus@10000000 {
+               gpio1: gpio@638 {
+                       status = "okay";
+               };
+
+               gpio2: gpio@660 {
+                       status = "okay";
+               };
+
+               gpio3: gpio@688 {
+                       status = "okay";
+               };
+
+               spi@b00 {
+                       status = "okay";
+
+                       m25p80@0 {
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+                               compatible = "jedec,spi-nor";
+                               reg = <0 0>;
+                               linux,modalias = "m25p80", "mx25l12805d";
+                               spi-max-frequency = <10000000>;
+
+                               partition@0 {
+                                       label = "u-boot";
+                                       reg = <0x0 0x30000>;
+                                       read-only;
+                               };
+
+                               partition@30000 {
+                                       label = "u-boot-env";
+                                       reg = <0x30000 0x10000>;
+                               };
+
+                               factory: partition@40000 {
+                                       label = "factory";
+                                       reg = <0x40000 0x10000>;
+                                       read-only;
+                               };
+
+                               partition@50000 {
+                                       label = "recover";
+                                       reg = <0x50000 0x1c0000>;
+                                       read-only;
+                               };
+
+                               partition@210000 {
+                                       label = "firmware";
+                                       reg = <0x210000 0xdf0000>;
+                               };
+                       };
+               };
+       };
+
+       ehci@101c0000 {
+               status = "okay";
+       };
+
+       ohci@101c1000 {
+               status = "okay";
+       };
+
+       ethernet@10100000 {
+               mtd-mac-address = <&factory 0x2e>;
+               mediatek,portmap = "llllw";
+       };
+
+       wmac@10180000 {
+               ralink,mtd-eeprom = <&factory 0>;
+       };
+
+       pinctrl {
+               state_default: pinctrl0 {
+                       default {
+                               ralink,group = "i2c", "ephy", "wled";
+                               ralink,function = "gpio";
+                       };
+               };
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+
+               wps {
+                       label = "wrh-300cr:green:wps";
+                       gpios = <&gpio2 0 1>;
+               };
+
+               ethernet {
+                       label = "wrh-300cr:green:ethernet";
+                       gpios = <&gpio2 3 1>;
+               };
+
+               wlan {
+                       label = "wrh-300cr:green:wlan";
+                       gpios = <&gpio3 0 1>;
+               };
+       };
+
+       gpio-keys-polled {
+               compatible = "gpio-keys-polled";
+               #address-cells = <1>;
+               #size-cells = <0>;
+               poll-interval = <20>;
+
+               reset {
+                       label = "reset";
+                       gpios = <&gpio0 1 1>;
+                       linux,code = <0x198>;
+               };
+
+               wps {
+                       label = "wps";
+                       gpios = <&gpio0 2 1>;
+                       linux,code = <0x211>;
+               };
+       };
+};

diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk
index 18cd20a45bd0c1d6a8487be9ee0e79f9f1087f41..c76e98e80974bc48d156d5c6228632ff4833d32f 100644 (file)
--- a/target/linux/ramips/image/mt7620.mk
+++ b/target/linux/ramips/image/mt7620.mk
@@ -64,6 +64,19 @@ endef
 BuildFirmware/Tplink/squashfs=$(call BuildFirmware/OF/tplink,$(1),$(2),$(3),$(4))
 BuildFirmware/Tplink/initramfs=$(call BuildFirmware/OF/tplink/initramfs,$(1),$(2),$(3),$(4))
 
+define BuildFirmware/WRH-300CR/squashfs
+       $(call BuildFirmware/Default16M/squashfs,$(1),$(2),$(3))
+       cp $(call sysupname,$(1),$(2)) $(KDIR)/v_0.0.0.bin
+       ( \
+               $(STAGING_DIR_HOST)/bin/md5sum $(KDIR)/v_0.0.0.bin | \
+                       sed 's/ .*//' && \
+               echo 458 \
+       ) | $(STAGING_DIR_HOST)/bin/md5sum | \
+               sed 's/ .*//' > $(KDIR)/v_0.0.0.md5
+       $(STAGING_DIR_HOST)/bin/tar -cf $(call imgname,$(1),$(2))-factory.bin -C $(KDIR) v_0.0.0.bin v_0.0.0.md5
+endef
+BuildFirmware/WRH-300CR/initramfs=$(call BuildFirmware/Default16M/initramfs,$(1),$(2),$(3))
+
 
 Image/Build/Profile/E1700=$(call BuildFirmware/UMedia/$(1),$(1),e1700,E1700,0x013326)
 ex2700_mtd_size=3866624
@@ -98,6 +111,7 @@ Image/Build/Profile/MLW221=$(call BuildFirmware/Default16M/$(1),$(1),mlw221,MLW2
 Image/Build/Profile/MLWG2=$(call BuildFirmware/Default16M/$(1),$(1),mlwg2,MLWG2)
 Image/Build/Profile/WMR-300=$(call BuildFirmware/Default8M/$(1),$(1),wmr-300,WMR-300)
 Image/Build/Profile/RT-N14U=$(call BuildFirmware/Default8M/$(1),$(1),rt-n14u,RT-N14U)
+Image/Build/Profile/WRH-300CR=$(call BuildFirmware/WRH-300CR/$(1),$(1),wrh-300cr,WRH-300CR)
 Image/Build/Profile/WRTNODE=$(call BuildFirmware/Default16M/$(1),$(1),wrtnode,WRTNODE)
 Image/Build/Profile/WT3020=$(call BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
 Image/Build/Profile/MIWIFI-MINI=$(call BuildFirmware/Default16M/$(1),$(1),miwifi-mini,MIWIFI-MINI)
@@ -143,6 +157,7 @@ define Image/Build/Profile/Default
        $(call Image/Build/Profile/MLWG2,$(1))
        $(call Image/Build/Profile/WMR-300,$(1))
        $(call Image/Build/Profile/RT-N14U,$(1))
+       $(call Image/Build/Profile/WRH-300CR,$(1))
        $(call Image/Build/Profile/WRTNODE,$(1))
        $(call Image/Build/Profile/WT3020,$(1))
        $(call Image/Build/Profile/MIWIFI-MINI,$(1))

diff --git a/target/linux/ramips/mt7620/profiles/elecom.mk b/target/linux/ramips/mt7620/profiles/elecom.mk
new file mode 100644 (file)
index 0000000..5c84c92
--- /dev/null
+++ b/target/linux/ramips/mt7620/profiles/elecom.mk
@@ -0,0 +1,18 @@
+#
+# Copyright (C) 2016 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+define Profile/WRH-300CR
+       NAME:=ELECOM WRH-300CR
+       PACKAGES:=\
+               kmod-usb-core kmod-usb2 kmod-usb-ohci kmod-usb-storage \
+               kmod-scsi-core kmod-fs-ext4 block-mount
+endef
+
+define Profile/WRH-300CR/Description
+       Package set optimized for the ELECOM WRH-300CR.
+endef
+$(eval $(call Profile,WRH-300CR))