--- /dev/null
+From 7a561e9351ae7e3fb1f08584d40b49c1e55dde60 Mon Sep 17 00:00:00 2001
+From: Samin Guo <samin.guo@starfivetech.com>
+Date: Thu, 20 Jul 2023 19:15:09 +0800
+Subject: [PATCH] net: phy: motorcomm: Add pad drive strength cfg support
+
+The motorcomm phy (YT8531) supports the ability to adjust the drive
+strength of the rx_clk/rx_data, and the default strength may not be
+suitable for all boards. So add configurable options to better match
+the boards.(e.g. StarFive VisionFive 2)
+
+When we configure the drive strength, we need to read the current
+LDO voltage value to ensure that it is a legal value at that LDO
+voltage.
+
+Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
+Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
+Reviewed-by: Andrew Lunn <andrew@lunn.ch>
+Signed-off-by: David S. Miller <davem@davemloft.net>
+---
+ drivers/net/phy/motorcomm.c | 118 ++++++++++++++++++++++++++++++++++++
+ 1 file changed, 118 insertions(+)
+
+--- a/drivers/net/phy/motorcomm.c
++++ b/drivers/net/phy/motorcomm.c
+@@ -163,6 +163,10 @@
+
+ #define YT8521_CHIP_CONFIG_REG 0xA001
+ #define YT8521_CCR_SW_RST BIT(15)
++#define YT8531_RGMII_LDO_VOL_MASK GENMASK(5, 4)
++#define YT8531_LDO_VOL_3V3 0x0
++#define YT8531_LDO_VOL_1V8 0x2
++
+ /* 1b0 disable 1.9ns rxc clock delay *default*
+ * 1b1 enable 1.9ns rxc clock delay
+ */
+@@ -236,6 +240,12 @@
+ */
+ #define YTPHY_WCR_TYPE_PULSE BIT(0)
+
++#define YTPHY_PAD_DRIVE_STRENGTH_REG 0xA010
++#define YT8531_RGMII_RXC_DS_MASK GENMASK(15, 13)
++#define YT8531_RGMII_RXD_DS_HI_MASK BIT(12) /* Bit 2 of rxd_ds */
++#define YT8531_RGMII_RXD_DS_LOW_MASK GENMASK(5, 4) /* Bit 1/0 of rxd_ds */
++#define YT8531_RGMII_RX_DS_DEFAULT 0x3
++
+ #define YTPHY_SYNCE_CFG_REG 0xA012
+ #define YT8521_SCR_SYNCE_ENABLE BIT(5)
+ /* 1b0 output 25m clock
+@@ -835,6 +845,110 @@ static int ytphy_rgmii_clk_delay_config_
+ }
+
+ /**
++ * struct ytphy_ldo_vol_map - map a current value to a register value
++ * @vol: ldo voltage
++ * @ds: value in the register
++ * @cur: value in device configuration
++ */
++struct ytphy_ldo_vol_map {
++ u32 vol;
++ u32 ds;
++ u32 cur;
++};
++
++static const struct ytphy_ldo_vol_map yt8531_ldo_vol[] = {
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 0, .cur = 1200},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 1, .cur = 2100},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 2, .cur = 2700},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 3, .cur = 2910},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 4, .cur = 3110},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 5, .cur = 3600},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 6, .cur = 3970},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 7, .cur = 4350},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 0, .cur = 3070},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 1, .cur = 4080},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 2, .cur = 4370},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 3, .cur = 4680},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 4, .cur = 5020},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 5, .cur = 5450},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 6, .cur = 5740},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 7, .cur = 6140},
++};
++
++static u32 yt8531_get_ldo_vol(struct phy_device *phydev)
++{
++ u32 val;
++
++ val = ytphy_read_ext_with_lock(phydev, YT8521_CHIP_CONFIG_REG);
++ val = FIELD_GET(YT8531_RGMII_LDO_VOL_MASK, val);
++
++ return val <= YT8531_LDO_VOL_1V8 ? val : YT8531_LDO_VOL_1V8;
++}
++
++static int yt8531_get_ds_map(struct phy_device *phydev, u32 cur)
++{
++ u32 vol;
++ int i;
++
++ vol = yt8531_get_ldo_vol(phydev);
++ for (i = 0; i < ARRAY_SIZE(yt8531_ldo_vol); i++) {
++ if (yt8531_ldo_vol[i].vol == vol && yt8531_ldo_vol[i].cur == cur)
++ return yt8531_ldo_vol[i].ds;
++ }
++
++ return -EINVAL;
++}
++
++static int yt8531_set_ds(struct phy_device *phydev)
++{
++ struct device_node *node = phydev->mdio.dev.of_node;
++ u32 ds_field_low, ds_field_hi, val;
++ int ret, ds;
++
++ /* set rgmii rx clk driver strength */
++ if (!of_property_read_u32(node, "motorcomm,rx-clk-drv-microamp", &val)) {
++ ds = yt8531_get_ds_map(phydev, val);
++ if (ds < 0)
++ return dev_err_probe(&phydev->mdio.dev, ds,
++ "No matching current value was found.\n");
++ } else {
++ ds = YT8531_RGMII_RX_DS_DEFAULT;
++ }
++
++ ret = ytphy_modify_ext_with_lock(phydev,
++ YTPHY_PAD_DRIVE_STRENGTH_REG,
++ YT8531_RGMII_RXC_DS_MASK,
++ FIELD_PREP(YT8531_RGMII_RXC_DS_MASK, ds));
++ if (ret < 0)
++ return ret;
++
++ /* set rgmii rx data driver strength */
++ if (!of_property_read_u32(node, "motorcomm,rx-data-drv-microamp", &val)) {
++ ds = yt8531_get_ds_map(phydev, val);
++ if (ds < 0)
++ return dev_err_probe(&phydev->mdio.dev, ds,
++ "No matching current value was found.\n");
++ } else {
++ ds = YT8531_RGMII_RX_DS_DEFAULT;
++ }
++
++ ds_field_hi = FIELD_GET(BIT(2), ds);
++ ds_field_hi = FIELD_PREP(YT8531_RGMII_RXD_DS_HI_MASK, ds_field_hi);
++
++ ds_field_low = FIELD_GET(GENMASK(1, 0), ds);
++ ds_field_low = FIELD_PREP(YT8531_RGMII_RXD_DS_LOW_MASK, ds_field_low);
++
++ ret = ytphy_modify_ext_with_lock(phydev,
++ YTPHY_PAD_DRIVE_STRENGTH_REG,
++ YT8531_RGMII_RXD_DS_LOW_MASK | YT8531_RGMII_RXD_DS_HI_MASK,
++ ds_field_low | ds_field_hi);
++ if (ret < 0)
++ return ret;
++
++ return 0;
++}
++
++/**
+ * yt8521_probe() - read chip config then set suitable polling_mode
+ * @phydev: a pointer to a &struct phy_device
+ *
+@@ -1518,6 +1632,10 @@ static int yt8531_config_init(struct phy
+ return ret;
+ }
+
++ ret = yt8531_set_ds(phydev);
++ if (ret < 0)
++ return ret;
++
+ return 0;
+ }
+
--- /dev/null
+From 7a561e9351ae7e3fb1f08584d40b49c1e55dde60 Mon Sep 17 00:00:00 2001
+From: Samin Guo <samin.guo@starfivetech.com>
+Date: Thu, 20 Jul 2023 19:15:09 +0800
+Subject: [PATCH] net: phy: motorcomm: Add pad drive strength cfg support
+
+The motorcomm phy (YT8531) supports the ability to adjust the drive
+strength of the rx_clk/rx_data, and the default strength may not be
+suitable for all boards. So add configurable options to better match
+the boards.(e.g. StarFive VisionFive 2)
+
+When we configure the drive strength, we need to read the current
+LDO voltage value to ensure that it is a legal value at that LDO
+voltage.
+
+Reviewed-by: Hal Feng <hal.feng@starfivetech.com>
+Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
+Reviewed-by: Andrew Lunn <andrew@lunn.ch>
+Signed-off-by: David S. Miller <davem@davemloft.net>
+---
+ drivers/net/phy/motorcomm.c | 118 ++++++++++++++++++++++++++++++++++++
+ 1 file changed, 118 insertions(+)
+
+--- a/drivers/net/phy/motorcomm.c
++++ b/drivers/net/phy/motorcomm.c
+@@ -163,6 +163,10 @@
+
+ #define YT8521_CHIP_CONFIG_REG 0xA001
+ #define YT8521_CCR_SW_RST BIT(15)
++#define YT8531_RGMII_LDO_VOL_MASK GENMASK(5, 4)
++#define YT8531_LDO_VOL_3V3 0x0
++#define YT8531_LDO_VOL_1V8 0x2
++
+ /* 1b0 disable 1.9ns rxc clock delay *default*
+ * 1b1 enable 1.9ns rxc clock delay
+ */
+@@ -236,6 +240,12 @@
+ */
+ #define YTPHY_WCR_TYPE_PULSE BIT(0)
+
++#define YTPHY_PAD_DRIVE_STRENGTH_REG 0xA010
++#define YT8531_RGMII_RXC_DS_MASK GENMASK(15, 13)
++#define YT8531_RGMII_RXD_DS_HI_MASK BIT(12) /* Bit 2 of rxd_ds */
++#define YT8531_RGMII_RXD_DS_LOW_MASK GENMASK(5, 4) /* Bit 1/0 of rxd_ds */
++#define YT8531_RGMII_RX_DS_DEFAULT 0x3
++
+ #define YTPHY_SYNCE_CFG_REG 0xA012
+ #define YT8521_SCR_SYNCE_ENABLE BIT(5)
+ /* 1b0 output 25m clock
+@@ -835,6 +845,110 @@ static int ytphy_rgmii_clk_delay_config_
+ }
+
+ /**
++ * struct ytphy_ldo_vol_map - map a current value to a register value
++ * @vol: ldo voltage
++ * @ds: value in the register
++ * @cur: value in device configuration
++ */
++struct ytphy_ldo_vol_map {
++ u32 vol;
++ u32 ds;
++ u32 cur;
++};
++
++static const struct ytphy_ldo_vol_map yt8531_ldo_vol[] = {
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 0, .cur = 1200},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 1, .cur = 2100},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 2, .cur = 2700},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 3, .cur = 2910},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 4, .cur = 3110},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 5, .cur = 3600},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 6, .cur = 3970},
++ {.vol = YT8531_LDO_VOL_1V8, .ds = 7, .cur = 4350},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 0, .cur = 3070},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 1, .cur = 4080},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 2, .cur = 4370},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 3, .cur = 4680},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 4, .cur = 5020},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 5, .cur = 5450},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 6, .cur = 5740},
++ {.vol = YT8531_LDO_VOL_3V3, .ds = 7, .cur = 6140},
++};
++
++static u32 yt8531_get_ldo_vol(struct phy_device *phydev)
++{
++ u32 val;
++
++ val = ytphy_read_ext_with_lock(phydev, YT8521_CHIP_CONFIG_REG);
++ val = FIELD_GET(YT8531_RGMII_LDO_VOL_MASK, val);
++
++ return val <= YT8531_LDO_VOL_1V8 ? val : YT8531_LDO_VOL_1V8;
++}
++
++static int yt8531_get_ds_map(struct phy_device *phydev, u32 cur)
++{
++ u32 vol;
++ int i;
++
++ vol = yt8531_get_ldo_vol(phydev);
++ for (i = 0; i < ARRAY_SIZE(yt8531_ldo_vol); i++) {
++ if (yt8531_ldo_vol[i].vol == vol && yt8531_ldo_vol[i].cur == cur)
++ return yt8531_ldo_vol[i].ds;
++ }
++
++ return -EINVAL;
++}
++
++static int yt8531_set_ds(struct phy_device *phydev)
++{
++ struct device_node *node = phydev->mdio.dev.of_node;
++ u32 ds_field_low, ds_field_hi, val;
++ int ret, ds;
++
++ /* set rgmii rx clk driver strength */
++ if (!of_property_read_u32(node, "motorcomm,rx-clk-drv-microamp", &val)) {
++ ds = yt8531_get_ds_map(phydev, val);
++ if (ds < 0)
++ return dev_err_probe(&phydev->mdio.dev, ds,
++ "No matching current value was found.\n");
++ } else {
++ ds = YT8531_RGMII_RX_DS_DEFAULT;
++ }
++
++ ret = ytphy_modify_ext_with_lock(phydev,
++ YTPHY_PAD_DRIVE_STRENGTH_REG,
++ YT8531_RGMII_RXC_DS_MASK,
++ FIELD_PREP(YT8531_RGMII_RXC_DS_MASK, ds));
++ if (ret < 0)
++ return ret;
++
++ /* set rgmii rx data driver strength */
++ if (!of_property_read_u32(node, "motorcomm,rx-data-drv-microamp", &val)) {
++ ds = yt8531_get_ds_map(phydev, val);
++ if (ds < 0)
++ return dev_err_probe(&phydev->mdio.dev, ds,
++ "No matching current value was found.\n");
++ } else {
++ ds = YT8531_RGMII_RX_DS_DEFAULT;
++ }
++
++ ds_field_hi = FIELD_GET(BIT(2), ds);
++ ds_field_hi = FIELD_PREP(YT8531_RGMII_RXD_DS_HI_MASK, ds_field_hi);
++
++ ds_field_low = FIELD_GET(GENMASK(1, 0), ds);
++ ds_field_low = FIELD_PREP(YT8531_RGMII_RXD_DS_LOW_MASK, ds_field_low);
++
++ ret = ytphy_modify_ext_with_lock(phydev,
++ YTPHY_PAD_DRIVE_STRENGTH_REG,
++ YT8531_RGMII_RXD_DS_LOW_MASK | YT8531_RGMII_RXD_DS_HI_MASK,
++ ds_field_low | ds_field_hi);
++ if (ret < 0)
++ return ret;
++
++ return 0;
++}
++
++/**
+ * yt8521_probe() - read chip config then set suitable polling_mode
+ * @phydev: a pointer to a &struct phy_device
+ *
+@@ -1518,6 +1632,10 @@ static int yt8531_config_init(struct phy
+ return ret;
+ }
+
++ ret = yt8531_set_ds(phydev);
++ if (ret < 0)
++ return ret;
++
+ return 0;
+ }
+
--- /dev/null
+From fc5a80a432607d05e85bba37971712405f75c546 Mon Sep 17 00:00:00 2001
+From: Tianling Shen <cnsztl@gmail.com>
+Date: Sat, 16 Dec 2023 12:07:23 +0800
+Subject: [PATCH] arm64: dts: rockchip: configure eth pad driver strength
+ for orangepi r1 plus lts
+
+The default strength is not enough to provide stable connection
+under 3.3v LDO voltage.
+
+Fixes: 387b3bbac5ea ("arm64: dts: rockchip: Add Xunlong OrangePi R1 Plus LTS")
+Cc: stable@vger.kernel.org # 6.6+
+Signed-off-by: Tianling Shen <cnsztl@gmail.com>
+Link: https://lore.kernel.org/r/20231216040723.17864-1-cnsztl@gmail.com
+Signed-off-by: Heiko Stuebner <heiko@sntech.de>
+---
+ arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts | 4 +++-
+ 1 file changed, 3 insertions(+), 1 deletion(-)
+
+--- a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
++++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus-lts.dts
+@@ -26,9 +26,11 @@
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+
++ motorcomm,auto-sleep-disabled;
+ motorcomm,clk-out-frequency-hz = <125000000>;
+ motorcomm,keep-pll-enabled;
+- motorcomm,auto-sleep-disabled;
++ motorcomm,rx-clk-drv-microamp = <5020>;
++ motorcomm,rx-data-drv-microamp = <5020>;
+
+ pinctrl-0 = <ð_phy_reset_pin>;
+ pinctrl-names = "default";
projects / openwrt / staging / wigyori.git / commitdiff