--- /dev/null
+From b7f492ca20e480ea3402692e165f919f20145935 Mon Sep 17 00:00:00 2001
+From: Oliver Schinagl <oliver@schinagl.nl>
+Date: Tue, 3 Dec 2013 12:07:01 +0100
+Subject: [PATCH] ARM: sunxi: Add an ahci-platform compatible AHCI driver for
+ the Allwinner SUNXi series of SoCs
+
+This patch adds support for the sunxi series of SoC's by allwinner. It
+plugs into the ahci-platform framework.
+
+Note: Currently it uses a somewhat hackish approach that probably needs
+a lot more work, but does the same as the IMX SoC's.
+
+Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
+---
+ .../devicetree/bindings/ata/ahci-sunxi.txt | 24 ++
+ drivers/ata/Kconfig | 9 +
+ drivers/ata/Makefile | 1 +
+ drivers/ata/ahci_platform.c | 12 +
+ drivers/ata/ahci_sunxi.c | 305 +++++++++++++++++++++
+ 5 files changed, 351 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/ata/ahci-sunxi.txt
+ create mode 100644 drivers/ata/ahci_sunxi.c
+
+diff --git a/Documentation/devicetree/bindings/ata/ahci-sunxi.txt b/Documentation/devicetree/bindings/ata/ahci-sunxi.txt
+new file mode 100644
+index 0000000..0792fa5
+--- /dev/null
++++ b/Documentation/devicetree/bindings/ata/ahci-sunxi.txt
+@@ -0,0 +1,24 @@
++Allwinner SUNXI AHCI SATA Controller
++
++SATA nodes are defined to describe on-chip Serial ATA controllers.
++Each SATA controller should have its own node.
++
++Required properties:
++- compatible : compatible list, contains "allwinner,sun4i-a10-ahci"
++- reg : <registers mapping>
++- interrupts : <interrupt mapping for AHCI IRQ>
++- clocks : clocks for ACHI
++- clock-names : clock names for AHCI
++
++Optional properties:
++- pwr-supply : regulator to control the power supply GPIO
++
++Example:
++ ahci@01c18000 {
++ compatible = "allwinner,sun4i-a10-ahci";
++ reg = <0x01c18000 0x1000>;
++ interrupts = <0 56 1>;
++ clocks = <&ahb_gates 25>, <&pll6 0>;
++ clock-names = "ahb_sata", "pll6_sata";
++ pwr-supply = <®_ahci_5v>;
++ };
+diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
+index 4e73772..b87e2ba 100644
+--- a/drivers/ata/Kconfig
++++ b/drivers/ata/Kconfig
+@@ -106,6 +106,15 @@ config AHCI_IMX
+
+ If unsure, say N.
+
++config AHCI_SUNXI
++ tristate "Allwinner sunxi AHCI SATA support"
++ depends on SATA_AHCI_PLATFORM && ARCH_SUNXI
++ help
++ This option enables support for the Allwinner sunxi SoC's
++ onboard AHCI SATA.
++
++ If unsure, say N.
++
+ config SATA_FSL
+ tristate "Freescale 3.0Gbps SATA support"
+ depends on FSL_SOC
+diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
+index 46518c6..246050b 100644
+--- a/drivers/ata/Makefile
++++ b/drivers/ata/Makefile
+@@ -11,6 +11,7 @@ obj-$(CONFIG_SATA_SIL24) += sata_sil24.o
+ obj-$(CONFIG_SATA_DWC) += sata_dwc_460ex.o
+ obj-$(CONFIG_SATA_HIGHBANK) += sata_highbank.o libahci.o
+ obj-$(CONFIG_AHCI_IMX) += ahci_imx.o
++obj-$(CONFIG_AHCI_SUNXI) += ahci_sunxi.o
+
+ # SFF w/ custom DMA
+ obj-$(CONFIG_PDC_ADMA) += pdc_adma.o
+diff --git a/drivers/ata/ahci_platform.c b/drivers/ata/ahci_platform.c
+index 4b231ba..1046b44 100644
+--- a/drivers/ata/ahci_platform.c
++++ b/drivers/ata/ahci_platform.c
+@@ -31,6 +31,7 @@ enum ahci_type {
+ AHCI, /* standard platform ahci */
+ IMX53_AHCI, /* ahci on i.mx53 */
+ STRICT_AHCI, /* delayed DMA engine start */
++ SUNXI_AHCI, /* ahci on sunxi */
+ };
+
+ static struct platform_device_id ahci_devtype[] = {
+@@ -44,6 +45,9 @@ enum ahci_type {
+ .name = "strict-ahci",
+ .driver_data = STRICT_AHCI,
+ }, {
++ .name = "sunxi-ahci",
++ .driver_data = SUNXI_AHCI,
++ }, {
+ /* sentinel */
+ }
+ };
+@@ -81,6 +85,14 @@ struct ata_port_operations ahci_platform_ops = {
+ .udma_mask = ATA_UDMA6,
+ .port_ops = &ahci_platform_ops,
+ },
++ [SUNXI_AHCI] = {
++ AHCI_HFLAGS (AHCI_HFLAG_32BIT_ONLY | AHCI_HFLAG_NO_MSI |
++ AHCI_HFLAG_NO_PMP | AHCI_HFLAG_YES_NCQ),
++ .flags = AHCI_FLAG_COMMON,
++ .pio_mask = ATA_PIO4,
++ .udma_mask = ATA_UDMA6,
++ .port_ops = &ahci_platform_ops,
++ },
+ };
+
+ static struct scsi_host_template ahci_platform_sht = {
+diff --git a/drivers/ata/ahci_sunxi.c b/drivers/ata/ahci_sunxi.c
+new file mode 100644
+index 0000000..982641f
+--- /dev/null
++++ b/drivers/ata/ahci_sunxi.c
+@@ -0,0 +1,305 @@
++/*
++ * Allwinner sunxi AHCI SATA platform driver
++ * Copyright 2013 Olliver Schinagl <oliver@schinagl.nl>
++ *
++ * Based on the AHCI SATA platform driver by Freescale and Allwinner
++ * Based on code from
++ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
++ * Daniel Wang <danielwang@allwinnertech.com>
++ *
++ * This program is free software; you can redistribute it and/or modify it
++ * under the terms and conditions of the GNU General Public License,
++ * version 2, as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope it will be useful, but WITHOUT
++ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
++ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
++ * more details.
++ *
++ * You should have received a copy of the GNU General Public License along with
++ * this program. If not, see <http://www.gnu.org/licenses/>.
++ */
++
++#include <linux/kernel.h>
++#include <linux/regulator/consumer.h>
++#include <linux/module.h>
++#include <linux/platform_device.h>
++#include <linux/mod_devicetable.h>
++#include <linux/of_device.h>
++#include <linux/ioport.h>
++#include <linux/device.h>
++#include <linux/gfp.h>
++#include <linux/clk.h>
++#include <linux/clk-provider.h>
++#include <linux/errno.h>
++#include <linux/ahci_platform.h>
++#include "ahci.h"
++
++#define DRV_NAME "sunxi-sata"
++
++#define AHCI_BISTAFR 0x00a0
++#define AHCI_BISTCR 0x00a4
++#define AHCI_BISTFCTR 0x00a8
++#define AHCI_BISTSR 0x00ac
++#define AHCI_BISTDECR 0x00b0
++#define AHCI_DIAGNR0 0x00b4
++#define AHCI_DIAGNR1 0x00b8
++#define AHCI_OOBR 0x00bc
++#define AHCI_PHYCS0R 0x00c0
++#define AHCI_PHYCS1R 0x00c4
++#define AHCI_PHYCS2R 0x00c8
++#define AHCI_TIMER1MS 0x00e0
++#define AHCI_GPARAM1R 0x00e8
++#define AHCI_GPARAM2R 0x00ec
++#define AHCI_PPARAMR 0x00f0
++#define AHCI_TESTR 0x00f4
++#define AHCI_VERSIONR 0x00f8
++#define AHCI_IDR 0x00fc
++#define AHCI_RWCR 0x00fc
++#define AHCI_P0DMACR 0x0170
++#define AHCI_P0PHYCR 0x0178
++#define AHCI_P0PHYSR 0x017c
++
++struct sunxi_ahci_data {
++ struct platform_device *ahci_pdev;
++ struct regulator *regulator;
++ struct clk *sata_clk;
++ struct clk *ahb_clk;
++};
++
++static void sunxi_clrbits(void __iomem *reg, u32 clr_val)
++{
++ u32 reg_val;
++
++ reg_val = readl(reg);
++ reg_val &= ~(clr_val);
++ writel(reg_val, reg);
++}
++
++static void sunxi_setbits(void __iomem *reg, u32 set_val)
++{
++ u32 reg_val;
++
++ reg_val = readl(reg);
++ reg_val |= set_val;
++ writel(reg_val, reg);
++}
++
++static void sunxi_clrsetbits(void __iomem *reg, u32 clr_val, u32 set_val)
++{
++ u32 reg_val;
++
++ reg_val = readl(reg);
++ reg_val &= ~(clr_val);
++ reg_val |= set_val;
++ writel(reg_val, reg);
++}
++
++static u32 sunxi_getbits(void __iomem *reg, u8 mask, u8 shift)
++{
++ return (readl(reg) >> shift) & mask;
++}
++
++static int sunxi_ahci_phy_init(struct device *dev, void __iomem *reg_base)
++{
++ u32 reg_val;
++ int timeout;
++
++ /* This magic is from the original code */
++ writel(0, reg_base + AHCI_RWCR);
++ mdelay(5);
++
++ sunxi_setbits(reg_base + AHCI_PHYCS1R, BIT(19));
++ sunxi_clrsetbits(reg_base + AHCI_PHYCS0R,
++ (0x7 << 24),
++ (0x5 << 24) | BIT(23) | BIT(18));
++ sunxi_clrsetbits(reg_base + AHCI_PHYCS1R,
++ (0x3 << 16) | (0x1f << 8) | (0x3 << 6),
++ (0x2 << 16) | (0x6 << 8) | (0x2 << 6));
++ sunxi_setbits(reg_base + AHCI_PHYCS1R, BIT(28) | BIT(15));
++ sunxi_clrbits(reg_base + AHCI_PHYCS1R, BIT(19));
++ sunxi_clrsetbits(reg_base + AHCI_PHYCS0R,
++ (0x7 << 20), (0x3 << 20));
++ sunxi_clrsetbits(reg_base + AHCI_PHYCS2R,
++ (0x1f << 5), (0x19 << 5));
++ mdelay(5);
++
++ sunxi_setbits(reg_base + AHCI_PHYCS0R, (0x1 << 19));
++
++ timeout = 0x100000;
++ do {
++ reg_val = sunxi_getbits(reg_base + AHCI_PHYCS0R, 0x7, 28);
++ } while (--timeout && (reg_val != 0x2));
++ if (!timeout)
++ dev_err(dev, "PHY power up failed.\n");
++
++ sunxi_setbits(reg_base + AHCI_PHYCS2R, (0x1 << 24));
++
++ timeout = 0x100000;
++ do {
++ reg_val = sunxi_getbits(reg_base + AHCI_PHYCS2R, 0x1, 24);
++ } while (--timeout && reg_val);
++ if (!timeout)
++ dev_err(dev, "PHY calibration failed.\n");
++ mdelay(15);
++
++ writel(0x7, reg_base + AHCI_RWCR);
++
++ return 0;
++}
++
++static int sunxi_ahci_init(struct device *dev, void __iomem *reg_base)
++{
++ struct sunxi_ahci_data *ahci_data;
++ int ret;
++
++ ahci_data = dev_get_drvdata(dev->parent);
++
++ ret = clk_prepare_enable(ahci_data->sata_clk);
++ if (ret < 0)
++ return ret;
++
++ ret = clk_prepare_enable(ahci_data->ahb_clk);
++ if (ret < 0)
++ return ret;
++
++ ret = regulator_enable(ahci_data->regulator);
++ if (ret)
++ return ret;
++
++ return sunxi_ahci_phy_init(dev, reg_base);
++}
++
++static void sunxi_ahci_exit(struct device *dev)
++{
++ struct sunxi_ahci_data *ahci_data;
++
++ ahci_data = dev_get_drvdata(dev->parent);
++
++ regulator_disable(ahci_data->regulator);
++
++ clk_disable_unprepare(ahci_data->ahb_clk);
++ clk_disable_unprepare(ahci_data->sata_clk);
++}
++
++static struct ahci_platform_data sunxi_ahci_pdata = {
++ .init = sunxi_ahci_init,
++ .exit = sunxi_ahci_exit,
++};
++
++static int sunxi_ahci_remove(struct platform_device *pdev)
++{
++ struct sunxi_ahci_data *ahci_data;
++
++ ahci_data = platform_get_drvdata(pdev);
++ platform_device_unregister(ahci_data->ahci_pdev);
++
++ dev_dbg(&pdev->dev, "driver unloaded\n");
++
++ return 0;
++}
++
++static const struct of_device_id sunxi_ahci_of_match[] = {
++ { .compatible = "allwinner,sun4i-a10-ahci", .data = &sunxi_ahci_pdata},
++ {/* sentinel */},
++};
++MODULE_DEVICE_TABLE(of, sunxi_ahci_of_match);
++
++static int sunxi_ahci_probe(struct platform_device *pdev)
++{
++ const struct ahci_platform_data *pdata;
++ const struct of_device_id *of_dev_id;
++ struct resource *mem, *irq, res[2];
++ struct platform_device *ahci_pdev;
++ struct sunxi_ahci_data *ahci_data;
++ struct regulator *regulator;
++ int ret;
++
++ regulator = devm_regulator_get(&pdev->dev, "pwr");
++ if (IS_ERR(regulator)) {
++ ret = PTR_ERR(regulator);
++ if (ret != -EPROBE_DEFER)
++ dev_err(&pdev->dev, "no regulator found (%d)\n", ret);
++ return ret;
++ }
++
++ ahci_data = devm_kzalloc(&pdev->dev, sizeof(*ahci_data), GFP_KERNEL);
++ if (!ahci_data)
++ return -ENOMEM;
++
++ ahci_pdev = platform_device_alloc("sunxi-ahci", -1);
++ if (!ahci_pdev)
++ return -ENODEV;
++
++ ahci_pdev->dev.parent = &pdev->dev;
++
++ ahci_data->regulator = regulator;
++ ahci_data->ahb_clk = devm_clk_get(&pdev->dev, "ahb_sata");
++ if (IS_ERR(ahci_data->ahb_clk)) {
++ ret = PTR_ERR(ahci_data->ahb_clk);
++ goto err_out;
++ }
++
++ ahci_data->sata_clk = devm_clk_get(&pdev->dev, "pll6_sata");
++ if (IS_ERR(ahci_data->sata_clk)) {
++ ret = PTR_ERR(ahci_data->sata_clk);
++ goto err_out;
++ }
++
++ ahci_data->ahci_pdev = ahci_pdev;
++ platform_set_drvdata(pdev, ahci_data);
++
++ ahci_pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
++ ahci_pdev->dev.dma_mask = &ahci_pdev->dev.coherent_dma_mask;
++ ahci_pdev->dev.of_node = pdev->dev.of_node;
++
++ of_dev_id = of_match_device(sunxi_ahci_of_match, &pdev->dev);
++ if (of_dev_id) {
++ pdata = of_dev_id->data;
++ } else {
++ ret = -EINVAL;
++ goto err_out;
++ }
++
++ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
++ if (!mem || !irq) {
++ ret = -ENOMEM;
++ goto err_out;
++ }
++ res[0] = *mem;
++ res[1] = *irq;
++ ret = platform_device_add_resources(ahci_pdev, res, 2);
++ if (ret)
++ goto err_out;
++
++ ret = platform_device_add_data(ahci_pdev, pdata, sizeof(*pdata));
++ if (ret)
++ goto err_out;
++
++ ret = platform_device_add(ahci_pdev);
++ if (ret)
++ goto err_out;
++
++ return 0;
++
++err_out:
++ platform_device_put(ahci_pdev);
++ return ret;
++}
++
++static struct platform_driver sunxi_ahci_driver = {
++ .probe = sunxi_ahci_probe,
++ .remove = sunxi_ahci_remove,
++ .driver = {
++ .name = DRV_NAME,
++ .owner = THIS_MODULE,
++ .of_match_table = sunxi_ahci_of_match,
++ },
++};
++module_platform_driver(sunxi_ahci_driver);
++
++MODULE_DESCRIPTION("Allwinner sunxi AHCI SATA platform driver");
++MODULE_AUTHOR("Olliver Schinagl <oliver@schinagl.nl>");
++MODULE_LICENSE("GPL");
++MODULE_ALIAS("ahci:sunxi");
+--
+1.8.5.1
+
--- /dev/null
+From e5b4d58432bec91414e82069a402d61e6aed631e Mon Sep 17 00:00:00 2001
+From: Oliver Schinagl <oliver@schinagl.nl>
+Date: Tue, 3 Dec 2013 12:10:11 +0100
+Subject: [PATCH] ARM: sunxi: dts: Add ahci support to a few A10 and A20 boards
+
+This patch adds sunxi sata support to A10 and A20 boards that have such
+a connector. Some boards also feature a regulator via a GPIO and support
+for this is also added.
+
+Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
+---
+ arch/arm/boot/dts/sun4i-a10-cubieboard.dts | 27 +++++++++++++++++++++++++
+ arch/arm/boot/dts/sun4i-a10.dtsi | 9 +++++++++
+ arch/arm/boot/dts/sun7i-a20-cubieboard2.dts | 27 +++++++++++++++++++++++++
+ arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 27 +++++++++++++++++++++++++
+ arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts | 26 ++++++++++++++++++++++++
+ arch/arm/boot/dts/sun7i-a20.dtsi | 9 +++++++++
+ 6 files changed, 125 insertions(+)
+
+diff --git a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts
+index d193937..63bd00d 100644
+--- a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts
++++ b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts
+@@ -51,7 +51,19 @@
+ status = "okay";
+ };
+
++ sata: ahci@01c18000 {
++ pwr-supply = <®_ahci_5v>;
++ status = "okay";
++ };
++
+ pinctrl@01c20800 {
++ ahci_pwr_pin: ahci_pwr_pin@0 {
++ allwinner,pins = "PB8";
++ allwinner,function = "gpio_out";
++ allwinner,drive = <0>;
++ allwinner,pull = <0>;
++ };
++
+ mmc0_cd_pin_cubieboard: mmc0_cd_pin@0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_in";
+@@ -102,4 +114,19 @@
+ linux,default-trigger = "heartbeat";
+ };
+ };
++
++ regulators {
++ compatible = "simple-bus";
++ pinctrl-names = "default";
++
++ reg_ahci_5v: ahci-5v {
++ compatible = "regulator-fixed";
++ regulator-name = "ahci-5v";
++ regulator-min-microvolt = <5000000>;
++ regulator-max-microvolt = <5000000>;
++ pinctrl-0 = <&ahci_pwr_pin>;
++ gpio = <&pio 1 8 0>;
++ enable-active-high;
++ };
++ };
+ };
+diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi
+index 13bccd5..a6dafec 100644
+--- a/arch/arm/boot/dts/sun4i-a10.dtsi
++++ b/arch/arm/boot/dts/sun4i-a10.dtsi
+@@ -315,6 +315,15 @@
+ status = "disabled";
+ };
+
++ sata: ahci@01c18000 {
++ compatible = "allwinner,sun4i-a10-ahci";
++ reg = <0x01c18000 0x1000>;
++ interrupts = <56>;
++ clocks = <&ahb_gates 25>, <&pll6 0>;
++ clock-names = "ahb_sata", "pll6_sata";
++ status = "disabled";
++ };
++
+ intc: interrupt-controller@01c20400 {
+ compatible = "allwinner,sun4i-ic";
+ reg = <0x01c20400 0x400>;
+diff --git a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts
+index ea55563..1d810bb 100644
+--- a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts
++++ b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts
+@@ -28,7 +28,19 @@
+ status = "okay";
+ };
+
++ sata: ahci@01c18000 {
++ pwr-supply = <®_ahci_5v>;
++ status = "okay";
++ };
++
+ pinctrl@01c20800 {
++ ahci_pwr_pin: ahci_pwr_pin@0 {
++ allwinner,pins = "PB8";
++ allwinner,function = "gpio_out";
++ allwinner,drive = <0>;
++ allwinner,pull = <0>;
++ };
++
+ mmc0_cd_pin_cubieboard2: mmc0_cd_pin@0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_in";
+@@ -86,4 +98,19 @@
+ gpios = <&pio 7 20 0>;
+ };
+ };
++
++ regulators {
++ compatible = "simple-bus";
++ pinctrl-names = "default";
++
++ reg_ahci_5v: ahci-5v {
++ compatible = "regulator-fixed";
++ regulator-name = "ahci-5v";
++ regulator-min-microvolt = <5000000>;
++ regulator-max-microvolt = <5000000>;
++ pinctrl-0 = <&ahci_pwr_pin>;
++ gpio = <&pio 1 8 0>;
++ enable-active-high;
++ };
++ };
+ };
+diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
+index bc04cc7..5e9f2ab 100644
+--- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
++++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts
+@@ -37,7 +37,19 @@
+ status = "okay";
+ };
+
++ sata: ahci@01c18000 {
++ pwr-supply = <®_ahci_5v>;
++ status = "okay";
++ };
++
+ pinctrl@01c20800 {
++ ahci_pwr_pin: ahci_pwr_pin@0 {
++ allwinner,pins = "PB8";
++ allwinner,function = "gpio_out";
++ allwinner,drive = <0>;
++ allwinner,pull = <0>;
++ };
++
+ mmc0_cd_pin_olinuxinom: mmc0_cd_pin@0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_in";
+@@ -116,4 +128,18 @@
+ default-state = "on";
+ };
+ };
++
++ regulators {
++ compatible = "simple-bus";
++
++ reg_ahci_5v: ahci-5v {
++ compatible = "regulator-fixed";
++ regulator-name = "ahci-5v";
++ regulator-min-microvolt = <5000000>;
++ regulator-max-microvolt = <5000000>;
++ pinctrl-0 = <&ahci_pwr_pin>;
++ gpio = <&pio 1 8 0>;
++ enable-active-high;
++ };
++ };
+ };
+diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi
+index 7ebfc89..f161590 100644
+--- a/arch/arm/boot/dts/sun7i-a20.dtsi
++++ b/arch/arm/boot/dts/sun7i-a20.dtsi
+@@ -432,6 +432,15 @@
+ };
+ };
+
++ sata: ahci@01c18000 {
++ compatible = "allwinner,sun4i-a10-ahci";
++ reg = <0x01c18000 0x1000>;
++ interrupts = <0 56 1>;
++ clocks = <&ahb_gates 25>, <&pll6 0>;
++ clock-names = "ahb_sata", "pll6_sata";
++ status = "disabled";
++ };
++
+ timer@01c20c00 {
+ compatible = "allwinner,sun4i-timer";
+ reg = <0x01c20c00 0x90>;
+--
+1.8.5.1
+
projects / openwrt / staging / blocktrron.git / commitdiff