mediatek: filogic: Add support for Wavlink WL-WN586X3
authorSijia Huang <engineer31@win-star.com>
Thu, 7 Mar 2024 02:12:11 +0000 (20:12 -0600)
committerHauke Mehrtens <hauke@hauke-m.de>
Sun, 9 Jun 2024 12:58:25 +0000 (14:58 +0200)
Hardware
--------
- SOC: MediaTek MT7981
- ram: 256MB DDR3
- FLASH: 16MB SPI-NOR
- Ethernet: 2x1Gb Lan 1x1Gb Wan
- WIFI: MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 2xLan 1x Wan 1x WIFI 1xSTATUS

MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
 2G: 80:3F:5D:xx:xx:x3 partition "factory" at 0x4 (binary), on label
 5G: 80:3F:5D:xx:xx:x3 Same as 2G

Installation Method 1: ssh
--------------------------
1. Connect PC to the lan port. Set the PC IP to 192.168.10.100 if
   required.
2. Navigate to http://192.168.10.1/
3. Log into the Wavlink WebGUI. Default username/password is
   admin/admin.
4. Use WebGUI to upgrade the firmware to
   WAVLINK_WN586X3-A_M86X3A_V240113_WO-GDBYFM-modified.bin
   downloaded from
   https://github.com/themaverickdm/firmware-misc/tree/main/wavlink/wl-wn586x3
   Warning: All settings will be lost!
5. Wait about 5 minutes, and after flashing is completed, log into
   the router using (with admin123 as password):
   ssh root@192.168.10.1
6. scp the openwrt image file onto the router, usually under /tmp
   somewhere.
   openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin
7. Flash openwrt image file like so:
   mtd write \
     openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin \
     firmware
   Warning: Previous firmware will be overwritten!
8. Wait about 5 minutes, and after the flashing is completed, set
   the PC IP to 192.168.1.100 if required and log into the router
   like so:
   ssh root@192.168.1.1

Installation Method 2: u-boot
-----------------------------
1. Connect UART:  TX-> 586X3 RX, RX-> 586X3 TX, GND-> 586 GND.
2. Connect PC to the wan (not lan!) port.
3. Setup the tftp server on PC, set IP to 192.168.10.100,
4. Power on the device. Select '2' to upgrade firmware in Uboot.
5. Input the image name and start to upgrade.

Uboot console log:

CPU:   MediaTek MT7981
Model: mt7981-rfb
DRAM:  256 MiB
Core:  34 devices, 13 uclasses, devicetree: embed
Loading Environment from nowhere... OK
In:    serial@11002000
Out:   serial@11002000
Err:   serial@11002000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address -
02:47:fb:b2:53:2d
eth0: ethernet@15100000
UBOOT WN586X3A
gpio: pin 9 (gpio 9) value is 0
gpio: pin 10 (gpio 10) value is 0
gpio: pin 5 (gpio 5) value is 0
gpio: pin 12 (gpio 12) value is 0
gpio: pin 13 (gpio 13) value is 0

  *** U-Boot Boot Menu ***

      1. Startup system (Default)
      2. Upgrade firmware
      3. Upgrade ATF BL2
      4. Upgrade ATF FIP
      5. Upgrade single image
      6. Load image
      0. U-Boot console

Co-authored-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: Sijia Huang <engineer31@win-star.com>
target/linux/mediatek/dts/mt7981b-wavlink-wl-wn586x3.dts [new file with mode: 0644]
target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
target/linux/mediatek/filogic/base-files/etc/board.d/02_network
target/linux/mediatek/image/filogic.mk

diff --git a/target/linux/mediatek/dts/mt7981b-wavlink-wl-wn586x3.dts b/target/linux/mediatek/dts/mt7981b-wavlink-wl-wn586x3.dts
new file mode 100644 (file)
index 0000000..62be0fa
--- /dev/null
@@ -0,0 +1,270 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include "mt7981.dtsi"
+
+/ {
+       model = "WAVLINK WL-WN586X3";
+       compatible = "wavlink,wl-wn586x3", "mediatek,mt7981";
+
+       aliases {
+               label-mac-device = &wifi;
+               led-boot = &led_status_blue;
+               led-failsafe = &led_status_blue;
+               led-running = &led_status_blue;
+               led-upgrade = &led_status_blue;
+               serial0 = &uart0;
+       };
+
+       chosen {
+               stdout-path = "serial0:115200n8";
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys";
+
+               button-reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&pio 11 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       leds {
+               compatible = "gpio-leds";
+
+               led-0 {
+                       color = <LED_COLOR_ID_BLUE>;
+                       function = LED_FUNCTION_WAN;
+                       gpios = <&pio 5 GPIO_ACTIVE_LOW>;
+               };
+
+               led-1 {
+                       color = <LED_COLOR_ID_BLUE>;
+                       function = LED_FUNCTION_WLAN;
+                       gpios = <&pio 9 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy1tpt";
+               };
+
+               led_status_blue: led-2 {
+                       color = <LED_COLOR_ID_BLUE>;
+                       function = LED_FUNCTION_STATUS;
+                       gpios = <&pio 10 GPIO_ACTIVE_LOW>;
+               };
+
+               led-3 {
+                       color = <LED_COLOR_ID_BLUE>;
+                       function = LED_FUNCTION_LAN;
+                       function-enumerator = <1>;
+                       gpios = <&pio 12 GPIO_ACTIVE_LOW>;
+               };
+
+               led-4 {
+                       color = <LED_COLOR_ID_BLUE>;
+                       function = LED_FUNCTION_LAN;
+                       function-enumerator = <2>;
+                       gpios = <&pio 13 GPIO_ACTIVE_LOW>;
+               };
+
+       };
+};
+
+&uart0 {
+       status = "okay";
+};
+
+&watchdog {
+       status = "okay";
+};
+
+&eth {
+       status = "okay";
+
+       gmac0: mac@0 {
+               compatible = "mediatek,eth-mac";
+               reg = <0>;
+               phy-mode = "2500base-x";
+               nvmem-cells = <&macaddr_hw_44e 0>;
+               nvmem-cell-names = "mac-address";
+
+               fixed-link {
+                       speed = <2500>;
+                       full-duplex;
+                       pause;
+               };
+       };
+
+       gmac1: mac@1 {
+               compatible = "mediatek,eth-mac";
+               reg = <1>;
+               phy-mode = "gmii";
+               phy-handle = <&int_gbe_phy>;
+               nvmem-cells = <&macaddr_hw_44e 1>;
+               nvmem-cell-names = "mac-address";
+       };
+};
+
+&mdio_bus {
+       switch: switch@1f {
+               compatible = "mediatek,mt7531";
+               reg = <31>;
+               reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
+               interrupt-controller;
+               #interrupt-cells = <1>;
+               interrupt-parent = <&pio>;
+               interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
+       };
+};
+
+&spi0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&spi0_flash_pins>;
+       status = "disabled";
+};
+
+&spi2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&spi2_flash_pins>;
+       status = "okay";
+
+       flash@0 {
+               #address-cells = <1>;
+               #size-cells = <1>;
+
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+
+               spi-max-frequency = <25000000>;
+               spi-tx-bus-width = <4>;
+               spi-rx-bus-width = <4>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@00000 {
+                               label = "bl2";
+                               reg = <0x00000 0x40000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "u-boot-env";
+                               reg = <0x40000 0x10000>;
+                               read-only;
+                       };
+
+                       factory: partition@50000 {
+                               label = "factory";
+                               reg = <0x50000 0xb0000>;
+                               read-only;
+
+                               nvmem-layout {
+                                       compatible = "fixed-layout";
+                                       #address-cells = <1>;
+                                       #size-cells = <1>;
+
+                                       macaddr_factory_4: macaddr@4 {
+                                               compatible = "mac-base";
+                                               reg = <0x4 0x6>;
+                                               #nvmem-cell-cells = <1>;
+                                       };
+                               };
+                       };
+
+                       partition@100000 {
+                               label = "fip";
+                               reg = <0x100000 0x80000>;
+                               read-only;
+                       };
+
+                       partition@f0000 {
+                               label = "firmware";
+                               reg = <0x180000 0xe00000>;
+                       };
+
+                       partition@f80000 {
+                               label = "hw";
+                               reg = <0xf80000 0x80000>;
+
+                               nvmem-layout {
+                                       compatible = "fixed-layout";
+                                       #address-cells = <1>;
+                                       #size-cells = <1>;
+
+                                       macaddr_hw_44e: macaddr@44e {
+                                               compatible = "mac-base";
+                                               reg = <0x44e 0x11>;
+                                               #nvmem-cell-cells = <1>;
+                                       };
+                               };
+                       };
+               };
+       };
+};
+
+&pio {
+       spi0_flash_pins: spi0-pins {
+               mux {
+                       function = "spi";
+                       groups = "spi0", "spi0_wp_hold";
+               };
+       };
+
+       spi2_flash_pins: spi2-pins {
+               mux {
+                       function = "spi";
+                       groups = "spi2", "spi2_wp_hold";
+               };
+
+               conf-pu {
+                       pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
+                       drive-strength = <8>;
+                       bias-pull-up = <103>;
+               };
+
+               conf-pd {
+                       pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
+                       drive-strength = <8>;
+                       bias-pull-down = <103>;
+               };
+       };
+};
+
+&switch {
+       ports {
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               port@1 {
+                       reg = <1>;
+                       label = "lan2";
+               };
+
+               port@2 {
+                       reg = <2>;
+                       label = "lan1";
+               };
+
+               port@6 {
+                       reg = <6>;
+                       ethernet = <&gmac0>;
+                       phy-mode = "2500base-x";
+
+                       fixed-link {
+                               speed = <2500>;
+                               full-duplex;
+                               pause;
+                       };
+               };
+       };
+};
+
+&wifi {
+       status = "okay";
+       mediatek,mtd-eeprom = <&factory 0x0>;
+       nvmem-cells = <&macaddr_factory_4 0>;
+       nvmem-cell-names = "mac-address";
+};
index 50ffb7e5d925dfe2ba6e267af65d037d7b092b20..ca462d2005f0a434904013b8da7d0b447c36ea8b 100644 (file)
@@ -91,6 +91,10 @@ smartrg,sdg-8734)
        ucidef_set_led_netdev "wan-green" "WAN" "mdio-bus:00:green:wan" "wan" "link_2500 link_5000"
        ucidef_set_led_netdev "wan-orange" "WAN" "mdio-bus:00:orange:wan" "wan" "link_100 link_1000"
        ucidef_set_led_netdev "wan-white" "WAN" "mdio-bus:00:white:wan" "wan" "link_10000"
+wavlink,wl-wn586x3)
+       ucidef_set_led_netdev "lan-1" "lan-1" "blue:lan-1" "lan1" "link tx rx"
+       ucidef_set_led_netdev "lan-2" "lan-2" "blue:lan-2" "lan2" "link tx rx"
+       ucidef_set_led_netdev "wan" "wan" "blue:wan" "eth1" "link tx rx"
        ;;
 xiaomi,mi-router-wr30u-stock|\
 xiaomi,mi-router-wr30u-ubootmod)
index 10dabc965a46d993b97fc01bc763b88fbd9d38df..cf777a63dff7bee1d74f5ce18e6879d281e20908 100644 (file)
@@ -96,7 +96,8 @@ mediatek_setup_interfaces()
        yuncore,ax835)
                ucidef_set_interfaces_lan_wan lan wan
                ;;
-       tplink,tl-xdr6086)
+       tplink,tl-xdr6086|\
+       wavlink,wl-wn586x3)
                ucidef_set_interfaces_lan_wan "lan1 lan2" eth1
                ;;
        xiaomi,mi-router-ax3000t|\
index 884ededd32471ab94b28bc5d1249b9d778a0948b..28a0f066af7b448b5e3f94d45b1178c59e653286 100644 (file)
@@ -1161,6 +1161,17 @@ define Device/unielec_u7981-01-nand
 endef
 TARGET_DEVICES += unielec_u7981-01-nand
 
+define Device/wavlink_wl-wn586x3
+  DEVICE_VENDOR := WAVLINK
+  DEVICE_MODEL := WL-WN586X3
+  DEVICE_DTS := mt7981b-wavlink-wl-wn586x3
+  DEVICE_DTS_DIR := ../dts
+  DEVICE_DTS_LOADADDR := 0x47000000
+  IMAGE_SIZE := 15424k
+  DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
+endef
+TARGET_DEVICES += wavlink_wl-wn586x3
+
 define Device/xiaomi_mi-router-ax3000t
   DEVICE_VENDOR := Xiaomi
   DEVICE_MODEL := Mi Router AX3000T