The NC650 / CP850 boards have long been unmaintained and left broken.
As obviously nobody is interested in that code any more, we may as
well remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
IVMS8_256 MPC860
LANTEC MPC850
LWMON MPC823
- NC650 MPC852
R360MPI MPC823
RMU MPC850
RRvision MPC823
+++ /dev/null
-#
-# (C) Copyright 2006 Detlev Zundel, dzu@denx.de
-# (C) Copyright 2004-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# See file CREDITS for list of people who contributed to this
-# project.
-#
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation; either version 2 of
-# the License, or (at your option) any later version.
-#
-# This program is distributed in the hope that it will be useful,
-# but WITHOUT ANY WARRANTY; without even the implied warranty of
-# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-# GNU General Public License for more details.
-#
-# You should have received a copy of the GNU General Public License
-# along with this program; if not, write to the Free Software
-# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
-# MA 02111-1307 USA
-#
-
-include $(TOPDIR)/config.mk
-
-LIB = $(obj)lib$(BOARD).a
-
-COBJS = $(BOARD).o nand.o flash.o
-
-SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
-OBJS := $(addprefix $(obj),$(COBJS))
-SOBJS := $(addprefix $(obj),$(SOBJS))
-
-$(LIB): $(obj).depend $(OBJS)
- $(AR) $(ARFLAGS) $@ $(OBJS)
-
-#########################################################################
-
-# defines $(obj).depend target
-include $(SRCTREE)/rules.mk
-
-sinclude $(obj).depend
-
-#########################################################################
+++ /dev/null
-/*
- * (C) Copyright 2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2001
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#undef DEBUG
-
-#include <common.h>
-#include <mpc8xx.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#ifndef CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ
-#define CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
- OR_SCY_2_CLK | OR_EHTR | OR_BI)
-#endif
-
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
-
-#if defined(CONFIG_ENV_IS_IN_FLASH)
-# ifndef CONFIG_ENV_ADDR
-# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
-# endif
-# ifndef CONFIG_ENV_SIZE
-# define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
-# endif
-# ifndef CONFIG_ENV_SECT_SIZE
-# define CONFIG_ENV_SECT_SIZE CONFIG_ENV_SIZE
-# endif
-#endif
-
-/*-----------------------------------------------------------------------
- * Protection Flags:
- */
-#define FLAG_PROTECT_SET 0x01
-#define FLAG_PROTECT_CLEAR 0x02
-
-/* Board support for 1 or 2 flash devices */
-#undef FLASH_PORT_WIDTH32
-#undef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH8
-
-#ifdef FLASH_PORT_WIDTH16
-#define FLASH_PORT_WIDTH ushort
-#define FLASH_PORT_WIDTHV vu_short
-#elif FLASH_PORT_WIDTH32
-#define FLASH_PORT_WIDTH ulong
-#define FLASH_PORT_WIDTHV vu_long
-#else /* FLASH_PORT_WIDTH8 */
-#define FLASH_PORT_WIDTH uchar
-#define FLASH_PORT_WIDTHV vu_char
-#endif
-
-#define FPW FLASH_PORT_WIDTH
-#define FPWV FLASH_PORT_WIDTHV
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (FPWV * addr, flash_info_t * info);
-static int write_data (flash_info_t * info, ulong dest, FPW data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- unsigned long size_b0;
- int i;
-#ifdef CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ
- int scy, trlx, flash_or_timing, clk_diff;
-
- scy = (CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & OR_SCY_MSK) >> 4;
- if (CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & OR_TRLX) {
- trlx = OR_TRLX;
- scy *= 2;
- } else
- trlx = 0;
-
- /* We assume that each 10MHz of bus clock require 1-clk SCY
- * adjustment.
- */
- clk_diff = (gd->bus_clk / 1000000) - 50;
-
- /* We need proper rounding here. This is what the "+5" and "-5"
- * are here for.
- */
- if (clk_diff >= 0)
- scy += (clk_diff + 5) / 10;
- else
- scy += (clk_diff - 5) / 10;
-
- /* For bus frequencies above 50MHz, we want to use relaxed
- * timing (OR_TRLX).
- */
- if (gd->bus_clk >= 50000000)
- trlx = OR_TRLX;
- else
- trlx = 0;
-
- if (trlx)
- scy /= 2;
-
- if (scy > 0xf)
- scy = 0xf;
- if (scy < 1)
- scy = 1;
-
- flash_or_timing = (scy << 4) | trlx |
- (CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ & ~(OR_TRLX | OR_SCY_MSK));
-#endif
-
- /* Init: no FLASHes known */
- for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) {
- flash_info[i].flash_id = FLASH_UNKNOWN;
- }
-
- /* Static FLASH Bank configuration here - FIXME XXX */
- size_b0 = flash_get_size ((FPW *) FLASH_BASE0_PRELIM, &flash_info[0]);
-
- if (flash_info[0].flash_id == FLASH_UNKNOWN) {
- printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
- size_b0, size_b0 << 20);
- }
-
- /* Remap FLASH according to real size */
-#ifndef CONFIG_SYS_OR_TIMING_FLASH_AT_50MHZ
- memctl->memc_or0 = CONFIG_SYS_OR_TIMING_FLASH | (-size_b0 & OR_AM_MSK);
-#else
- memctl->memc_or0 = flash_or_timing | (-size_b0 & OR_AM_MSK);
-#endif
- memctl->memc_br0 = (CONFIG_SYS_FLASH_BASE & BR_BA_MSK) | BR_PS_8 | BR_MS_GPCM | BR_V;
-
- /* Re-do sizing to get full correct info */
- size_b0 = flash_get_size ((FPW *) CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
- flash_get_offsets (CONFIG_SYS_FLASH_BASE, &flash_info[0]);
-
-#if CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE
- /* monitor protection ON by default */
- (void) flash_protect (FLAG_PROTECT_SET,
- CONFIG_SYS_MONITOR_BASE,
- CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1,
- &flash_info[0]);
-#endif
-
-#ifdef CONFIG_ENV_IS_IN_FLASH
- /* ENV protection ON by default */
- flash_protect (FLAG_PROTECT_SET,
- CONFIG_ENV_ADDR,
- CONFIG_ENV_ADDR + CONFIG_ENV_SIZE - 1,
- &flash_info[0]);
-#endif
-
- flash_info[0].size = size_b0;
-
- return (size_b0);
-}
-
-/*-----------------------------------------------------------------------
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return;
- }
-
- if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL) {
- for (i = 0; i < info->sector_count; i++) {
- info->start[i] = base + (i * 0x00020000);
- }
- }
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
- int i;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("missing or unknown FLASH type\n");
- return;
- }
-
- switch (info->flash_id & FLASH_VENDMASK) {
- case FLASH_MAN_INTEL:
- printf ("INTEL ");
- break;
- default:
- printf ("Unknown Vendor ");
- break;
- }
-
- switch (info->flash_id & FLASH_TYPEMASK) {
- case FLASH_28F320J3A:
- printf ("28F320J3A\n");
- break;
- case FLASH_28F640J3A:
- printf ("28F640J3A\n");
- break;
- case FLASH_28F128J3A:
- printf ("28F128J3A\n");
- break;
- default:
- printf ("Unknown Chip Type\n");
- break;
- }
-
- printf (" Size: %ld MB in %d Sectors\n",
- info->size >> 20, info->sector_count);
-
- printf (" Sector Start Addresses:");
- for (i = 0; i < info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf ("\n ");
- printf (" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " ");
- }
- printf ("\n");
- return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-
-static ulong flash_get_size (FPWV * addr, flash_info_t * info)
-{
- FPW value;
-
- addr[0] = (FPW) 0x00900090;
-
- value = addr[0];
-
- debug ("Manuf. ID @ 0x%08lx: 0x%08lx\n", (ulong)addr, value);
-
- switch (value) {
- case (FPW) INTEL_MANUFACT:
- info->flash_id = FLASH_MAN_INTEL;
- break;
- default:
- info->flash_id = FLASH_UNKNOWN;
- info->sector_count = 0;
- info->size = 0;
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
- return (0); /* no or unknown flash */
- }
-
-#ifdef FLASH_PORT_WIDTH8
- value = addr[2]; /* device ID */
-#else
- value = addr[1]; /* device ID */
-#endif
-
- debug ("Device ID @ 0x%08lx: 0x%08lx\n", (ulong)(&addr[1]), value);
-
- switch (value) {
- case (FPW) INTEL_ID_28F320J3A:
- info->flash_id += FLASH_28F320J3A;
- info->sector_count = 32;
- info->size = 0x00400000;
- break; /* => 4 MB */
-
- case (FPW) INTEL_ID_28F640J3A:
- info->flash_id += FLASH_28F640J3A;
- info->sector_count = 64;
- info->size = 0x00800000;
- break; /* => 8 MB */
-
- case (FPW) INTEL_ID_28F128J3A:
- info->flash_id += FLASH_28F128J3A;
- info->sector_count = 128;
- info->size = 0x01000000;
- break; /* => 16 MB */
-
- default:
- info->flash_id = FLASH_UNKNOWN;
- break;
- }
-
- if (info->sector_count > CONFIG_SYS_MAX_FLASH_SECT) {
- printf ("** ERROR: sector count %d > max (%d) **\n",
- info->sector_count, CONFIG_SYS_MAX_FLASH_SECT);
- info->sector_count = CONFIG_SYS_MAX_FLASH_SECT;
- }
-
- addr[0] = (FPW) 0x00FF00FF; /* restore read mode */
-
- return (info->size);
-}
-
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
- int flag, prot, sect;
- ulong type, start, now, last;
- int rcode = 0;
-
- if ((s_first < 0) || (s_first > s_last)) {
- if (info->flash_id == FLASH_UNKNOWN) {
- printf ("- missing\n");
- } else {
- printf ("- no sectors to erase\n");
- }
- return 1;
- }
-
- type = (info->flash_id & FLASH_VENDMASK);
- if ((type != FLASH_MAN_INTEL)) {
- printf ("Can't erase unknown flash type %08lx - aborted\n",
- info->flash_id);
- return 1;
- }
-
- prot = 0;
- for (sect = s_first; sect <= s_last; ++sect) {
- if (info->protect[sect]) {
- prot++;
- }
- }
-
- if (prot) {
- printf ("- Warning: %d protected sectors will not be erased!\n",
- prot);
- } else {
- printf ("\n");
- }
-
- start = get_timer (0);
- last = start;
- /* Start erase on unprotected sectors */
- for (sect = s_first; sect <= s_last; sect++) {
- if (info->protect[sect] == 0) { /* not protected */
- FPWV *addr = (FPWV *) (info->start[sect]);
- FPW status;
-
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- *addr = (FPW) 0x00500050; /* clear status register */
- *addr = (FPW) 0x00200020; /* erase setup */
- *addr = (FPW) 0x00D000D0; /* erase confirm */
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts ();
-
- /* wait at least 80us - let's wait 1 ms */
- udelay (1000);
-
- while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
- if ((now = get_timer (start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
- printf ("Timeout\n");
- *addr = (FPW) 0x00B000B0; /* suspend erase */
- *addr = (FPW) 0x00FF00FF; /* reset to read mode */
- rcode = 1;
- break;
- }
-
- /* show that we're waiting */
- if ((now - last) > 1000) { /* every second */
- putc ('.');
- last = now;
- }
- }
-
- *addr = (FPW) 0x00FF00FF; /* reset to read mode */
- }
- }
- printf (" done\n");
- return rcode;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- * 4 - Flash not identified
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
- ulong cp, wp;
- FPW data;
-
- int i, l, rc, port_width;
-
- if (info->flash_id == FLASH_UNKNOWN) {
- return 4;
- }
-/* get lower word aligned address */
-#ifdef FLASH_PORT_WIDTH16
- wp = (addr & ~1);
- port_width = 2;
-#elif defined(FLASH_PORT_WIDTH32)
- wp = (addr & ~3);
- port_width = 4;
-#else
- wp = addr;
- port_width = 1;
-#endif
-
- /*
- * handle unaligned start bytes
- */
- if ((l = addr - wp) != 0) {
- data = 0;
- for (i = 0, cp = wp; i < l; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
- for (; i < port_width && cnt > 0; ++i) {
- data = (data << 8) | *src++;
- --cnt;
- ++cp;
- }
- for (; cnt == 0 && i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- if ((rc = write_data (info, wp, data)) != 0) {
- return (rc);
- }
- wp += port_width;
- }
-
- /*
- * handle word aligned part
- */
- while (cnt >= port_width) {
- data = 0;
- for (i = 0; i < port_width; ++i) {
- data = (data << 8) | *src++;
- }
- if ((rc = write_data (info, wp, data)) != 0) {
- return (rc);
- }
- wp += port_width;
- cnt -= port_width;
- }
-
- if (cnt == 0) {
- return (0);
- }
-
- /*
- * handle unaligned tail bytes
- */
- data = 0;
- for (i = 0, cp = wp; i < port_width && cnt > 0; ++i, ++cp) {
- data = (data << 8) | *src++;
- --cnt;
- }
- for (; i < port_width; ++i, ++cp) {
- data = (data << 8) | (*(uchar *) cp);
- }
-
- return (write_data (info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word or halfword to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_data (flash_info_t * info, ulong dest, FPW data)
-{
- FPWV *addr = (FPWV *) dest;
- ulong status;
- ulong start;
- int flag;
-
- /* Check if Flash is (sufficiently) erased */
- if ((*addr & data) != data) {
- printf ("not erased at %08lx (%x)\n", (ulong) addr, *addr);
- return (2);
- }
- /* Disable interrupts which might cause a timeout here */
- flag = disable_interrupts ();
-
- *addr = (FPW) 0x00400040; /* write setup */
- *addr = data;
-
- /* re-enable interrupts if necessary */
- if (flag)
- enable_interrupts ();
-
- start = get_timer (0);
-
- while (((status = *addr) & (FPW) 0x00800080) != (FPW) 0x00800080) {
- if (get_timer (start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
- *addr = (FPW) 0x00FF00FF; /* restore read mode */
- return (1);
- }
- }
-
- *addr = (FPW) 0x00FF00FF; /* restore read mode */
-
- return (0);
-}
+++ /dev/null
-/*
- * (C) Copyright 2006 Detlev Zundel, dzu@denx.de
- * (C) Copyright 2006 DENX Software Engineering
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <asm/io.h>
-
-#if defined(CONFIG_CMD_NAND)
-
-#include <nand.h>
-
-#if defined(CONFIG_IDS852_REV1)
-/*
- * hardware specific access to control-lines
- */
-static void nc650_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
- struct nand_chip *this = mtd->priv;
-
- if (ctrl & NAND_CTRL_CHANGE) {
- if ( ctrl & NAND_CLE )
- this->IO_ADDR_W += 2;
- else
- this->IO_ADDR_W -= 2;
- if ( ctrl & NAND_ALE )
- this->IO_ADDR_W += 1;
- else
- this->IO_ADDR_W -= 1;
- }
-
- if (cmd != NAND_CMD_NONE)
- writeb(cmd, this->IO_ADDR_W);
-}
-#elif defined(CONFIG_IDS852_REV2)
-/*
- * hardware specific access to control-lines
- */
-static void nc650_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
-{
- struct nand_chip *this = mtd->priv;
-
- if (ctrl & NAND_CTRL_CHANGE) {
- if ( ctrl & NAND_CLE )
- writeb(0, (volatile __u8 *) this->IO_ADDR_W + 0xa);
- else
- writeb(0, (volatile __u8 *) this->IO_ADDR_W) + 0x8);
- if ( ctrl & NAND_ALE )
- writeb(0, (volatile __u8 *) this->IO_ADDR_W) + 0x9);
- else
- writeb(0, (volatile __u8 *) this->IO_ADDR_W) + 0x8);
- if ( ctrl & NAND_NCE )
- writeb(0, (volatile __u8 *) this->IO_ADDR_W) + 0x8);
- else
- writeb(0, (volatile __u8 *) this->IO_ADDR_W) + 0xc);
- }
-
- if (cmd != NAND_CMD_NONE)
- writeb(cmd, this->IO_ADDR_W);
-}
-#else
-#error Unknown IDS852 module revision
-#endif
-
-/*
- * Board-specific NAND initialization. The following members of the
- * argument are board-specific (per include/linux/mtd/nand.h):
- * - IO_ADDR_R?: address to read the 8 I/O lines of the flash device
- * - IO_ADDR_W?: address to write the 8 I/O lines of the flash device
- * - cmd_ctrl: hardwarespecific function for accesing control-lines
- * - dev_ready: hardwarespecific function for accesing device ready/busy line
- * - enable_hwecc?: function to enable (reset) hardware ecc generator. Must
- * only be provided if a hardware ECC is available
- * - eccm.ode: mode of ecc, see defines
- * - chip_delay: chip dependent delay for transfering data from array to
- * read regs (tR)
- * - options: various chip options. They can partly be set to inform
- * nand_scan about special functionality. See the defines for further
- * explanation
- * Members with a "?" were not set in the merged testing-NAND branch,
- * so they are not set here either.
- */
-int board_nand_init(struct nand_chip *nand)
-{
-
- nand->cmd_ctrl = nc650_hwcontrol;
- nand->ecc.mode = NAND_ECC_SOFT;
- nand->chip_delay = 12;
-/* nand->options = NAND_SAMSUNG_LP_OPTIONS;*/
- return 0;
-}
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2006 Detlev Zundel, dzu@denx.de
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-#include <common.h>
-#include <config.h>
-#include <mpc8xx.h>
-
-/*
- * Memory Controller Using
- *
- * CS0 - Flash memory (0x40000000)
- * CS3 - SDRAM (0x00000000}
- */
-
-/* ------------------------------------------------------------------------- */
-
-#define _not_used_ 0xffffffff
-
-const uint sdram_table[] = {
- /* single read. (offset 0 in upm RAM) */
- 0x1f07fc04, 0xeeaefc04, 0x11adfc04, 0xefbbbc00,
- 0x1ff77c47,
-
- /* MRS initialization (offset 5) */
-
- 0x1ff77c34, 0xefeabc34, 0x1fb57c35,
-
- /* burst read. (offset 8 in upm RAM) */
- 0x1f07fc04, 0xeeaefc04, 0x10adfc04, 0xf0affc00,
- 0xf0affc00, 0xf1affc00, 0xefbbbc00, 0x1ff77c47,
- _not_used_, _not_used_, _not_used_, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* single write. (offset 18 in upm RAM) */
- 0x1f27fc04, 0xeeaebc00, 0x01b93c04, 0x1ff77c47,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* burst write. (offset 20 in upm RAM) */
- 0x1f07fc04, 0xeeaebc00, 0x10ad7c00, 0xf0affc00,
- 0xf0affc00, 0xe1bbbc04, 0x1ff77c47, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* refresh. (offset 30 in upm RAM) */
- 0x1ff5fc84, 0xfffffc04, 0xfffffc04, 0xfffffc04,
- 0xfffffc84, 0xfffffc07, _not_used_, _not_used_,
- _not_used_, _not_used_, _not_used_, _not_used_,
-
- /* exception. (offset 3c in upm RAM) */
- 0x7ffffc07, _not_used_, _not_used_, _not_used_
-};
-
-const uint nand_flash_table[] = {
- /* single read. (offset 0 in upm RAM) */
- 0x0ff3fc04, 0x0ff3fc04, 0x0ff3fc04, 0x0ffffc04,
- 0xfffffc00, 0xfffffc05, 0xfffffc05, 0xfffffc05,
-
- /* burst read. (offset 8 in upm RAM) */
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05,
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05,
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05,
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05,
-
- /* single write. (offset 18 in upm RAM) */
- 0x00fffc04, 0x00fffc04, 0x00fffc04, 0x0ffffc04,
- 0x0ffffc84, 0x0ffffc84, 0xfffffc00, 0xfffffc05,
-
- /* burst write. (offset 20 in upm RAM) */
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05,
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05,
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05,
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05,
-
- /* refresh. (offset 30 in upm RAM) */
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05,
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05,
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05,
-
- /* exception. (offset 3c in upm RAM) */
- 0xffffcc05, 0xffffcc05, 0xffffcc05, 0xffffcc05
-};
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check Board Identity:
- */
-
-int checkboard (void)
-{
-#if !defined(CONFIG_CP850)
- puts ("Board: NC650");
-#else
- puts ("Board: CP850");
-#endif
-#if defined(CONFIG_IDS852_REV1)
- puts (" with IDS852 rev 1 module\n");
-#elif defined(CONFIG_IDS852_REV2)
- puts (" with IDS852 rev 2 module\n");
-#endif
- return 0;
-}
-
-/* ------------------------------------------------------------------------- */
-
-static long int dram_size (long int, long int *, long int);
-
-/* ------------------------------------------------------------------------- */
-
-phys_size_t initdram (int board_type)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- long int size8, size9;
- long int size_b0 = 0;
- unsigned long reg;
-
- upmconfig (UPMA, (uint *) sdram_table,
- sizeof (sdram_table) / sizeof (uint));
-
- /*
- * Preliminary prescaler for refresh (depends on number of
- * banks): This value is selected for four cycles every 62.4 us
- * with two SDRAM banks or four cycles every 31.2 us with one
- * bank. It will be adjusted after memory sizing.
- */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
-
- memctl->memc_mar = 0x00000088;
-
- /*
- * Map controller bank 1 to the SDRAM bank at
- * preliminary address - these have to be modified after the
- * SDRAM size has been determined.
- */
- memctl->memc_or3 = CONFIG_SYS_OR3_PRELIM;
- memctl->memc_br3 = CONFIG_SYS_BR3_PRELIM;
-
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
-
- udelay (200);
-
- /* perform SDRAM initializsation sequence */
-
- memctl->memc_mcr = 0x80006105; /* SDRAM bank 0 */
- udelay (200);
- memctl->memc_mcr = 0x80006230; /* SDRAM bank 0 - execute twice */
- udelay (200);
-
- memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
-
- udelay (1000);
-
- /*
- * Check Bank 0 Memory Size for re-configuration
- *
- * try 8 column mode
- */
- size8 = dram_size (CONFIG_SYS_MAMR_8COL, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE);
-
- udelay (1000);
-
- /*
- * try 9 column mode
- */
- size9 = dram_size (CONFIG_SYS_MAMR_9COL, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE);
-
- udelay (1000);
-
- if (size8 < size9) {
- size_b0 = size9;
- } else {
- size_b0 = size8;
- memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
- udelay (500);
- }
-
- /*
- * Adjust refresh rate depending on SDRAM type, both banks.
- * For types > 128 MBit leave it at the current (fast) rate
- */
- if ((size_b0 < 0x02000000)) {
- /* reduce to 15.6 us (62.4 us / quad) */
- memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
- udelay (1000);
- }
-
- /*
- * Final mapping
- */
-
- memctl->memc_or3 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
- memctl->memc_br3 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
-
- /* adjust refresh rate depending on SDRAM type, one bank */
- reg = memctl->memc_mptpr;
- reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
- memctl->memc_mptpr = reg;
-
- udelay (10000);
-
- /* Configure UPMB for NAND flash access */
- upmconfig (UPMB, (uint *) nand_flash_table,
- sizeof (nand_flash_table) / sizeof (uint));
-
- memctl->memc_mbmr = CONFIG_SYS_MBMR_NAND;
-
- return (size_b0);
-}
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * Check memory range for valid RAM. A simple memory test determines
- * the actually available RAM size between addresses `base' and
- * `base + maxsize'. Some (not all) hardware errors are detected:
- * - short between address lines
- * - short between data lines
- */
-
-static long int dram_size (long int mamr_value, long int *base, long int maxsize)
-{
- volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
-
- memctl->memc_mamr = mamr_value;
-
- return (get_ram_size(base, maxsize));
-}
-
-
-#if defined(CONFIG_CP850)
-
-#define DPRAM_VARNAME "KP850DIP"
-#define PARAM_ADDR 0x7C0
-#define NAME_ADDR 0x7F8
-#define BOARD_NAME "KP01"
-#define DEFAULT_LB "241111"
-
-int misc_init_r(void)
-{
- int iCompatMode = 0;
- char *pParam = NULL;
- char *envlb;
-
- /*
- First byte in CPLD read address space signals compatibility mode
- 0 - cp850
- 1 - kp852
- */
- pParam = (char*)(CONFIG_SYS_CPLD_BASE);
- if( *pParam != 0)
- iCompatMode = 1;
-
- if ( iCompatMode != 0) {
- /*
- In KP852 compatibility mode we have to write to
- DPRAM as early as possible the binary coded
- line config and board name.
- The line config is derived from the environment
- variable DPRAM_VARNAME by converting from ASCII
- to binary per character.
- */
- if ( (envlb = getenv ( DPRAM_VARNAME )) == 0) {
- setenv( DPRAM_VARNAME, DEFAULT_LB);
- envlb = DEFAULT_LB;
- }
-
- /* Status string */
- printf("Mode: KP852(LB=%s)\n", envlb);
-
- /* copy appl init */
- pParam = (char*)(DPRAM_BASE_ADDR + PARAM_ADDR);
- while (*envlb) {
- *(pParam++) = *(envlb++) - '0';
- }
- *pParam = '\0';
-
- /* copy board id */
- pParam = (char*)(DPRAM_BASE_ADDR + NAME_ADDR);
- strcpy( pParam, BOARD_NAME);
- } else {
- puts("Mode: CP850\n");
- }
-
- return 0;
-}
-#endif
+++ /dev/null
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text)
- *(.text)
- *(.got1)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(.eh_frame)
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
- __u_boot_cmd_start = .;
- .u_boot_cmd : { *(.u_boot_cmd) }
- __u_boot_cmd_end = .;
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- . = ALIGN(4);
- }
- _end = . ;
- PROVIDE (end = .);
-}
+++ /dev/null
-/*
- * (C) Copyright 2001
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- arch/powerpc/cpu/mpc8xx/start.o (.text)
- *(.text)
- *(.got1)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(.rodata)
- *(.rodata1)
- *(.rodata.str1.4)
- *(.eh_frame)
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x0FFF) & 0xFFFFF000;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
- __u_boot_cmd_start = .;
- .u_boot_cmd : { *(.u_boot_cmd) }
- __u_boot_cmd_end = .;
-
-
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(4096);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(4096);
- __init_end = .;
-
- __bss_start = .;
- .bss :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- }
- _end = . ;
- PROVIDE (end = .);
-}
TQM885D powerpc mpc8xx tqm8xx tqc
AMX860 powerpc mpc8xx amx860 westel
AdderII powerpc mpc8xx adder - - Adder:MPC852T
-CP850 powerpc mpc8xx nc650 - - NC650:CP850=1,IDS852_REV2=1
IVML24 powerpc mpc8xx ivm - - IVML24:IVML24_16M
IVMS8 powerpc mpc8xx ivm - - IVMS8:IVMS8_16M
NETTA powerpc mpc8xx netta - - NETTA
IVML24_256 powerpc mpc8xx ivm - - IVML24:IVML24_64M
IVMS8_128 powerpc mpc8xx ivm - - IVMS8:IVMS8_32M
IVMS8_256 powerpc mpc8xx ivm - - IVMS8:IVMS8_64M
-NC650_Rev1 powerpc mpc8xx nc650 - - NC650:IDS852_REV2=1
-NC650_Rev2 powerpc mpc8xx nc650 - - NC650:IDS852_REV1=1
NETTA2_V2 powerpc mpc8xx netta2 - - NETTA2:NETTA2_VERSION=2
NETTA_6412 powerpc mpc8xx netta - - NETTA:NETTA_6412=1
NETTA_ISDN powerpc mpc8xx netta - - NETTA:NETTA_ISDN=1
+++ /dev/null
-/*
- * (C) Copyright 2006, 2007 Detlev Zundel, dzu@denx.de
- * (C) Copyright 2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC852T 1
-#define CONFIG_NC650 1
-
-#define CONFIG_SYS_TEXT_BASE 0x40700000
-
-#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
-#undef CONFIG_8xx_CONS_SMC2
-#undef CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-
-/*
- * 10 MHz - PLL input clock
- */
-#define CONFIG_8xx_OSCLK 10000000
-
-/*
- * 50 MHz - default CPU clock
- */
-#define CONFIG_8xx_CPUCLK_DEFAULT 50000000
-
-/*
- * 15 MHz - CPU minimum clock
- */
-#define CONFIG_SYS_8xx_CPUCLK_MIN 15000000
-
-/*
- * 133 MHz - CPU maximum clock
- */
-#define CONFIG_SYS_8xx_CPUCLK_MAX 133000000
-
-#define CONFIG_SYS_MEASURE_CPUCLK
-#define CONFIG_SYS_8XX_XIN CONFIG_8xx_OSCLK
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT \
- "\nEnter password - autoboot in %d seconds...\n", bootdelay
-#define CONFIG_AUTOBOOT_DELAY_STR "ids"
-#define CONFIG_BOOT_RETRY_TIME 900
-#define CONFIG_BOOT_RETRY_MIN 30
-
-#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
-
-#undef CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND \
- "bootp;" \
- "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
- "bootm"
-
-#define CONFIG_WATCHDOG /* watchdog enabled */
-
-#undef CONFIG_STATUS_LED /* Status LED disabled */
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_BOOTFILESIZE
-
-
-#define CONFIG_FEC_ENET 1 /* use FEC ethernet */
-#define FEC_ENET
-#define CONFIG_MII
-#define CONFIG_SYS_DISCOVER_PHY 1
-
-
-/* enable I2C and select the hardware/software driver */
-#undef CONFIG_HARD_I2C /* I2C with hardware support */
-#define CONFIG_SOFT_I2C 1 /* I2C bit-banged */
-#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7f
-
-/*
- * Software (bit-bang) I2C driver configuration
- */
-#if defined(CONFIG_IDS852_REV1)
-
-#define SCL 0x1000 /* PA 3 */
-#define SDA 0x2000 /* PA 2 */
-
-#define __I2C_DIR immr->im_ioport.iop_padir
-#define __I2C_DAT immr->im_ioport.iop_padat
-#define __I2C_PAR immr->im_ioport.iop_papar
-
-#elif defined(CONFIG_IDS852_REV2)
-
-#define SCL 0x0002 /* PB 30 */
-#define SDA 0x0001 /* PB 31 */
-
-#define __I2C_PAR immr->im_cpm.cp_pbpar
-#define __I2C_DIR immr->im_cpm.cp_pbdir
-#define __I2C_DAT immr->im_cpm.cp_pbdat
-
-#endif
-
-#define I2C_INIT { __I2C_PAR &= ~(SDA|SCL); \
- __I2C_DIR |= (SDA|SCL); }
-#define I2C_READ ((__I2C_DAT & SDA) ? 1 : 0)
-#define I2C_SDA(x) { if (x) __I2C_DAT |= SDA; else __I2C_DAT &= ~SDA; }
-#define I2C_SCL(x) { if (x) __I2C_DAT |= SCL; else __I2C_DAT &= ~SCL; }
-#define I2C_DELAY { udelay(5); }
-#define I2C_ACTIVE { __I2C_DIR |= SDA; }
-#define I2C_TRISTATE { __I2C_DIR &= ~SDA; }
-
-#define CONFIG_RTC_PCF8563
-#define CONFIG_SYS_I2C_RTC_ADDR 0x51
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x00100000
-
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR 0xF0000000
-#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024))
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
-#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
-#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE 0x00000000
-#define CONFIG_SYS_FLASH_BASE 0x40000000
-
-#define CONFIG_SYS_RESET_ADDRESS 0xFFF00100
-
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 256 kB for malloc() */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
-#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max number of sectors on one chip */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
-
-
-#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x00740000
-
-#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment sector */
-#define CONFIG_ENV_SIZE 0x4000 /* Used Size of Environment Sector */
-
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
-#endif
-
-/*
- * NAND flash support
- */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control 11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
- SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration 11-6
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control 11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- */
-#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control 11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- */
-#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register 15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK SCCR_EBDF11
-#define CONFIG_SYS_SCCR (SCCR_COM00 | SCCR_DFSYNC00 | \
- SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \
- SCCR_DFLCD000 | SCCR_DFALCD00)
-
- /*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER 0
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
-
-#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
-
-/* FLASH timing: Default value of OR0 after reset */
-#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
- OR_SCY_15_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V)
-
-/*
- * BR2 and OR2 (NAND Flash) - addressed through UPMB on rev 1
- * rev2 only uses the chipselect
- */
-#define CONFIG_SYS_NAND_BASE 0x50000000
-#define CONFIG_SYS_NAND_SIZE 0x04000000
-
-#define CONFIG_SYS_OR_TIMING_NAND (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
- OR_SCY_15_CLK | OR_EHTR | OR_TRLX)
-
-#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_NAND_BASE & BR_BA_MSK) | BR_PS_8 | BR_MS_UPMB | BR_V )
-#define CONFIG_SYS_OR2_PRELIM (((-CONFIG_SYS_NAND_SIZE) & OR_AM_MSK) | OR_BI )
-
-/*
- * BR3 and OR3 (SDRAM)
- */
-#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank */
-#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
-
- /*
- * SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)
- */
-#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
-
-#define CONFIG_SYS_OR3_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM)
-#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V)
-
-/*
- * BR4 and OR4 (CPLD)
- */
-#define CONFIG_SYS_CPLD_BASE 0x80000000 /* CPLD */
-#define CONFIG_SYS_CPLD_SIZE 0x10000 /* only 16 used */
-
-#define CONFIG_SYS_OR_TIMING_CPLD (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
- OR_SCY_1_CLK)
-
-#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_CPLD_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
-#define CONFIG_SYS_OR4_PRELIM (((-CONFIG_SYS_CPLD_SIZE) & OR_AM_MSK) | CONFIG_SYS_OR_TIMING_CPLD)
-
-/*
- * BR5 and OR5 (SRAM)
- */
-#define CONFIG_SYS_SRAM_BASE 0x60000000
-#define CONFIG_SYS_SRAM_SIZE 0x00080000
-
-#define CONFIG_SYS_OR_TIMING_SRAM (OR_CSNT_SAM | OR_ACS_DIV1 | OR_BI | \
- OR_SCY_15_CLK | OR_EHTR | OR_TRLX)
-
-#define CONFIG_SYS_BR5_PRELIM ((CONFIG_SYS_SRAM_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
-#define CONFIG_SYS_OR5_PRELIM (((-CONFIG_SYS_SRAM_SIZE) & OR_AM_MSK) | CONFIG_SYS_OR_TIMING_SRAM)
-
-#if defined(CONFIG_CP850)
-/*
- * BR6 and OR6 (DPRAM) - only on CP850
- */
-#define CONFIG_SYS_OR6_PRELIM 0xffff8170
-#define CONFIG_SYS_BR6_PRELIM 0xa0000401
-#define DPRAM_BASE_ADDR 0xa0000000
-
-#define CONFIG_MISC_INIT_R 1
-#endif
-
-/*
- * 4096 Rows from SDRAM example configuration
- * 1000 factor s -> ms
- * 64 PTP (pre-divider from MPTPR) from SDRAM example configuration
- * 4 Number of refresh cycles per period
- * 64 Refresh cycle in ms per number of rows
- */
-#define CONFIG_SYS_PTA_PER_CLK ((4096 * 64 * 1000) / (4 * 64))
-
-/*
- * Memory Periodic Timer Prescaler
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA 39
-
-/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
-#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
-
-/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
-#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
-#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
-
-/*
- * MAMR settings for SDRAM
- */
-
-#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
- MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
- MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
-
-/*
- * MBMR settings for NAND flash
- */
-
-#define CONFIG_SYS_MBMR_NAND ( MBMR_WLFB_5X )
-
-#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
-#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */
-
-/*
- * JFFS2 partitions
- */
-
-/* No command line, one static partition */
-#undef CONFIG_CMD_MTDPARTS
-#define CONFIG_JFFS2_DEV "nand0"
-#define CONFIG_JFFS2_PART_SIZE 0x00400000
-#define CONFIG_JFFS2_PART_OFFSET 0x00000000
-
-/* mtdparts command line support */
-#define CONFIG_CMD_MTDPARTS
-#define MTDIDS_DEFAULT "nor0=nc650-0,nand0=nc650-nand"
-
-#define MTDPARTS_DEFAULT "mtdparts=nc650-0:1m(kernel1),1m(kernel2)," \
- "4m(cramfs1),1m(cramfs2)," \
- "256k(u-boot),128k(env);" \
- "nc650-nand:4m(jffs1),28m(jffs2)"
-
-#endif /* __CONFIG_H */
projects / project / bcm63xx / u-boot.git / commitdiff