ath79: add support for ROSINSON WR818 board

This commit adds support for the ROSINSON WR818 WiFi-Router

SoC:    Qualcomm Atheros QCA9563,
FLASH:  Winbond W25Q128FV 16MBytes,
WiFi:   QCA9563 b/g/n 3x3 450Mbit/s,
USB:    1x USB 2.0 Type A, 1x USB2.0 Type C,
IN:     WPS/Reset button GPIO1,
OUT:    Power LED red, Internet LED red, WLAN LED red,
        LAN1 LED red, LAN2 LED red, System LED red,
UART:   RX-GPIO18, TX-GPIO22,

Tested and working:
    - Ethernet (LAN + WAN)
    - WiFi
    - OpenWRT sysupgrade
    - Button
    - LEDs

Installation of OpenWRT from vendor firmware:
    - Connect to the Web-interface at http://192.168.1.1
    - Go to "Administration" -> "Firmware Upgrade"
    - Upload the OpenWrt sysupgrade image

Signed-off-by: Rosy Song <rosysong@rosinson.com>

diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index f4718822134e95acb5db04861236272cebc8b163..b9d6c709e7d91c7b42280a5318b8f4a3e04d6994 100755 (executable)
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -111,6 +111,10 @@ ath79_setup_interfaces()
                ucidef_add_switch "switch0" \
                        "0@eth0" "3:lan:1" "5:lan:2" "4:wan"
                ;;
+       rosinson,wr818)
+               ucidef_add_switch "switch0" \
+                       "0@eth0" "1:lan" "2:lan" "3:wan"
+               ;;
        tplink,archer-c7-v1|\
        tplink,archer-c7-v2|\
        tplink,tl-wdr4900-v2)
@@ -230,6 +234,10 @@ ath79_setup_macs()
                lan_mac=$(k2t_get_mac "lan_mac")
                wan_mac=$(k2t_get_mac "wan_mac")
                ;;
+       rosinson,wr818)
+               wan_mac=$(mtd_get_mac_binary factory 0)
+               lan_mac=$(macaddr_setbit_la "$wan_mac")
+               ;;
        tplink,tl-wr1043nd-v4)
                base_mac=$(mtd_get_mac_binary product-info 8)
                wan_mac=$(macaddr_add "$base_mac" 1)

diff --git a/target/linux/ath79/dts/qca9563_rosinson_wr818.dts b/target/linux/ath79/dts/qca9563_rosinson_wr818.dts
new file mode 100644 (file)
index 0000000..ff853cc
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_rosinson_wr818.dts
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca956x.dtsi"
+
+/ {
+       model = "ROSINSON WR818";
+       compatible = "rosinson,wr818", "qca,qca9560";
+
+       chosen {
+               bootargs = "console=ttyS0,115200n8";
+       };
+
+       aliases {
+               led-boot = &system;
+               led-failsafe = &system;
+               led-running = &system;
+               led-upgrade = &system;
+       };
+
+       gpio_leds: leds {
+               compatible = "gpio-leds";
+
+               system: system {
+                       label = "wr818:red:system";
+                       gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+               };
+
+               wifi_2g {
+                       label = "wr818:red:wifi2g";
+                       gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+                       linux,default-trigger = "phy0tpt";
+               };
+       };
+
+       keys {
+               compatible = "gpio-keys";
+
+               reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+                       debounce-interval = <60>;
+               };
+       };
+};
+
+&uart {
+       status = "okay";
+};
+
+&gpio {
+       status = "okay";
+};
+
+&spi {
+       num-cs = <1>;
+
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <25000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               label = "u-boot";
+                               reg = <0x000000 0x040000>;
+                               read-only;
+                       };
+
+                       partition@40000 {
+                               label = "u-boot-env";
+                               reg = <0x040000 0x010000>;
+                               read-only;
+                       };
+
+                       partition@50000 {
+                               label = "firmware";
+                               reg = <0x050000 0xf80000>;
+                       };
+
+                       info: partition@fd0000 {
+                               label = "factory";
+                               reg = <0xfd0000 0x010000>;
+                               read-only;
+                       };
+
+                       art: partition@ff0000 {
+                               label = "art";
+                               reg = <0xff0000 0x010000>;
+                               read-only;
+                       };
+               };
+       };
+};
+
+&mdio0 {
+       status = "okay";
+
+       phy-mask = <0>;
+       phy0: ethernet-phy@0 {
+               reg = <0>;
+               phy-mode = "sgmii";
+
+               qca,ar8327-initvals = <
+                       0x04 0x00080080 /* PORT0 PAD MODE CTRL */
+                       0x7c 0x0000007e /* PORT0_STATUS */
+               >;
+       };
+};
+
+&eth0 {
+       status = "okay";
+
+       mtd-mac-address = <&info 0x0>;
+       phy-mode = "sgmii";
+       phy-handle = <&phy0>;
+};
+
+&wmac {
+       status = "okay";
+       mtd-cal-data = <&art 0x1000>;
+};
+
+&usb_phy0 {
+       status = "okay";
+};
+
+&usb0 {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       status = "okay";
+
+       port@1 {
+               reg = <1>;
+               #trigger-source-cells = <0>;
+       };
+};
+
+&usb_phy1 {
+       status = "okay";
+};
+
+&usb1 {
+       #address-cells = <1>;
+       #size-cells = <0>;
+       status = "okay";
+
+       port@2 {
+               reg = <2>;
+               #trigger-source-cells = <0>;
+       };
+};

diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 48d477dd9e252a202c3c3b3084023f4bda5bce69..2b4556bc76e029274d5182aa4d04ae09b01be6f9 100644 (file)
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -344,6 +344,14 @@ define Device/phicomm_k2t
 endef
 TARGET_DEVICES += phicomm_k2t
 
+define Device/rosinson_wr818
+  ATH_SOC := qca9563
+  DEVICE_TITLE := ROSINSON WR818
+  IMAGE_SIZE := 15872k
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
+endef
+TARGET_DEVICES += rosinson_wr818
+
 define Device/wd_mynet-wifi-rangeextender
   ATH_SOC := ar9344
   DEVICE_TITLE := Western Digital My Net Wi-Fi Range Extender