--- /dev/null
+/*
+ * (C) Copyright 2010, Damien Dusha, <d.dusha@gmail.com>
+ *
+ * (C) Copyright 2009, Value Team S.p.A.
+ * Francesco Rendine, <francesco.rendine@valueteam.com>
+ *
+ * (C) Copyright 2009 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2008, Excito Elektronik i Sk=E5ne AB
+ *
+ * Author: Tor Krill tor@excito.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <usb.h>
+#include <asm/io.h>
+#include <usb/ehci-fsl.h>
+
+#include "ehci.h"
+#include "ehci-core.h"
+
+static void fsl_setup_phy(volatile struct ehci_hcor *);
+static void fsl_platform_set_host_mode(volatile struct usb_ehci *ehci);
+static int reset_usb_controller(volatile struct usb_ehci *ehci);
+static void usb_platform_dr_init(volatile struct usb_ehci *ehci);
+
+/*
+ * Initialize SOC FSL EHCI Controller
+ *
+ * This code is derived from EHCI FSL USB Linux driver for MPC5121
+ *
+ */
+int ehci_hcd_init(void)
+{
+ volatile struct usb_ehci *ehci;
+
+ /* Hook the memory mapped registers for EHCI-Controller */
+ ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB_ADDR;
+ hccr = (struct ehci_hccr *)((uint32_t)&(ehci->caplength));
+ hcor = (struct ehci_hcor *)((uint32_t) hccr +
+ HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
+
+ /* configure interface for UTMI_WIDE */
+ usb_platform_dr_init(ehci);
+
+ /* Init Phy USB0 to UTMI+ */
+ fsl_setup_phy(hcor);
+
+ /* Set to host mode */
+ fsl_platform_set_host_mode(ehci);
+
+ /*
+ * Setting the burst size seems to be required to prevent the
+ * USB from hanging when communicating with certain USB Mass
+ * storage devices. This was determined by analysing the
+ * EHCI registers under Linux vs U-Boot and burstsize was the
+ * major non-interrupt related difference between the two
+ * implementations.
+ *
+ * Some USB sticks behave better than others. In particular,
+ * the following USB stick is especially problematic:
+ * 0930:6545 Toshiba Corp
+ *
+ * The burstsize is set here to match the Linux implementation.
+ */
+ out_be32(&ehci->burstsize, FSL_EHCI_TXPBURST(8) |
+ FSL_EHCI_RXPBURST(8));
+
+ return 0;
+}
+
+/*
+ * Destroy the appropriate control structures corresponding
+ * the the EHCI host controller.
+ */
+int ehci_hcd_stop(void)
+{
+ volatile struct usb_ehci *ehci;
+ int exit_status = 0;
+
+ if (hcor) {
+ /* Unhook struct */
+ hccr = NULL;
+ hcor = NULL;
+
+ /* Reset the USB controller */
+ ehci = (struct usb_ehci *)CONFIG_SYS_FSL_USB_ADDR;
+ exit_status = reset_usb_controller(ehci);
+ }
+
+ return exit_status;
+}
+
+static int reset_usb_controller(volatile struct usb_ehci *ehci)
+{
+ unsigned int i;
+
+ /* Command a reset of the USB Controller */
+ out_be32(&(ehci->usbcmd), EHCI_FSL_USBCMD_RST);
+
+ /* Wait for the reset process to finish */
+ for (i = 65535 ; i > 0 ; i--) {
+ /*
+ * The host will set this bit to zero once the
+ * reset process is complete
+ */
+ if ((in_be32(&(ehci->usbcmd)) & EHCI_FSL_USBCMD_RST) == 0)
+ return 0;
+ }
+
+ /* Hub did not reset in time */
+ return -1;
+}
+
+static void fsl_setup_phy(volatile struct ehci_hcor *hcor)
+{
+ uint32_t portsc;
+
+ portsc = ehci_readl(&hcor->or_portsc[0]);
+ portsc &= ~(PORT_PTS_MSK | PORT_PTS_PTW);
+
+ /* Enable the phy mode to UTMI Wide */
+ portsc |= PORT_PTS_PTW;
+ portsc |= PORT_PTS_UTMI;
+
+ ehci_writel(&hcor->or_portsc[0], portsc);
+}
+
+static void fsl_platform_set_host_mode(volatile struct usb_ehci *ehci)
+{
+ uint32_t temp;
+
+ temp = in_le32(&ehci->usbmode);
+ temp |= CM_HOST | ES_BE;
+ out_le32(&ehci->usbmode, temp);
+}
+
+static void usb_platform_dr_init(volatile struct usb_ehci *ehci)
+{
+ /* Configure interface for UTMI_WIDE */
+ out_be32(&ehci->isiphyctrl, PHYCTRL_PHYE | PHYCTRL_PXE);
+ out_be32(&ehci->usbgenctrl, GC_PPP | GC_PFP );
+}
#define PORT_PTS_ULPI (2 << 30)
#define PORT_PTS_SERIAL (3 << 30)
#define PORT_PTS_PTW (1 << 28)
+#define PORT_PFSC (1 << 24) /* Defined on Page 39-44 of the mpc5151 ERM */
+#define PORT_PTS_PHCD (1 << 23)
+#define PORT_PP (1 << 12)
+#define PORT_PR (1 << 8)
/* USBMODE Register bits */
#define CM_IDLE (0 << 0)
#define CM_RESERVED (1 << 0)
#define CM_DEVICE (2 << 0)
#define CM_HOST (3 << 0)
+#define ES_BE (1 << 2) /* Big Endian Select, default is LE */
#define USBMODE_RESERVED_2 (0 << 2)
#define SLOM (1 << 3)
#define SDIS (1 << 4)
#define PHY_CLK_VALID (1 << 17)
#define FSL_SOC_USB_PORTSC2 0x188
+
+/* OTG Status Control Register bits */
+#define FSL_SOC_USB_OTGSC 0x1a4
+#define CTRL_VBUS_DISCHARGE (0x1<<0)
+#define CTRL_VBUS_CHARGE (0x1<<1)
+#define CTRL_OTG_TERMINATION (0x1<<3)
+#define CTRL_DATA_PULSING (0x1<<4)
+#define CTRL_ID_PULL_EN (0x1<<5)
+#define HA_DATA_PULSE (0x1<<6)
+#define HA_BA (0x1<<7)
+#define STS_USB_ID (0x1<<8)
+#define STS_A_VBUS_VALID (0x1<<9)
+#define STS_A_SESSION_VALID (0x1<<10)
+#define STS_B_SESSION_VALID (0x1<<11)
+#define STS_B_SESSION_END (0x1<<12)
+#define STS_1MS_TOGGLE (0x1<<13)
+#define STS_DATA_PULSING (0x1<<14)
+#define INTSTS_USB_ID (0x1<<16)
+#define INTSTS_A_VBUS_VALID (0x1<<17)
+#define INTSTS_A_SESSION_VALID (0x1<<18)
+#define INTSTS_B_SESSION_VALID (0x1<<19)
+#define INTSTS_B_SESSION_END (0x1<<20)
+#define INTSTS_1MS (0x1<<21)
+#define INTSTS_DATA_PULSING (0x1<<22)
+#define INTR_USB_ID_EN (0x1<<24)
+#define INTR_A_VBUS_VALID_EN (0x1<<25)
+#define INTR_A_SESSION_VALID_EN (0x1<<26)
+#define INTR_B_SESSION_VALID_EN (0x1<<27)
+#define INTR_B_SESSION_END_EN (0x1<<28)
+#define INTR_1MS_TIMER_EN (0x1<<29)
+#define INTR_DATA_PULSING_EN (0x1<<30)
+#define INTSTS_MASK (0x00ff0000)
+
+/* USBCMD Bits of interest */
+#define EHCI_FSL_USBCMD_RST (1 << 1)
+#define EHCI_FSL_USBCMD_RS (1 << 0)
+
+#define INTERRUPT_ENABLE_BITS_MASK \
+ (INTR_USB_ID_EN | \
+ INTR_1MS_TIMER_EN | \
+ INTR_A_VBUS_VALID_EN | \
+ INTR_A_SESSION_VALID_EN | \
+ INTR_B_SESSION_VALID_EN | \
+ INTR_B_SESSION_END_EN | \
+ INTR_DATA_PULSING_EN)
+
+#define INTERRUPT_STATUS_BITS_MASK \
+ (INTSTS_USB_ID | \
+ INTR_1MS_TIMER_EN | \
+ INTSTS_A_VBUS_VALID | \
+ INTSTS_A_SESSION_VALID | \
+ INTSTS_B_SESSION_VALID | \
+ INTSTS_B_SESSION_END | \
+ INTSTS_DATA_PULSING)
+
#define FSL_SOC_USB_USBMODE 0x1a8
+
+#define USBGENCTRL 0x200 /* NOTE: big endian */
+#define GC_WU_INT_CLR (1 << 5) /* Wakeup int clear */
+#define GC_ULPI_SEL (1 << 4) /* ULPI i/f select (usb0 only)*/
+#define GC_PPP (1 << 3) /* Port Power Polarity */
+#define GC_PFP (1 << 2) /* Power Fault Polarity */
+#define GC_WU_ULPI_EN (1 << 1) /* Wakeup on ULPI event */
+#define GC_WU_IE (1 << 1) /* Wakeup interrupt enable */
+
+#define ISIPHYCTRL 0x204 /* NOTE: big endian */
+#define PHYCTRL_PHYE (1 << 4) /* On-chip UTMI PHY enable */
+#define PHYCTRL_BSENH (1 << 3) /* Bit Stuff Enable High */
+#define PHYCTRL_BSEN (1 << 2) /* Bit Stuff Enable */
+#define PHYCTRL_LSFE (1 << 1) /* Line State Filter Enable */
+#define PHYCTRL_PXE (1 << 0) /* PHY oscillator enable */
+
#define FSL_SOC_USB_SNOOP1 0x400 /* NOTE: big-endian */
#define FSL_SOC_USB_SNOOP2 0x404 /* NOTE: big-endian */
#define FSL_SOC_USB_AGECNTTHRSH 0x408 /* NOTE: big-endian */
#define MPC83XX_SCCR_USB_DRCM_01 0x00100000
#define MPC83XX_SCCR_USB_DRCM_10 0x00200000
-#if defined(CONFIG_MPC83xx)
-#define CONFIG_SYS_MPC8xxx_USB_ADDR CONFIG_SYS_MPC83xx_USB_ADDR
+#if defined(CONFIG_MPC83XX)
+#define CONFIG_SYS_FSL_USB_ADDR CONFIG_SYS_MPC83xx_USB_ADDR
#elif defined(CONFIG_MPC85xx)
-#define CONFIG_SYS_MPC8xxx_USB_ADDR CONFIG_SYS_MPC85xx_USB_ADDR
+#define CONFIG_SYS_FSL_USB_ADDR CONFIG_SYS_MPC85xx_USB_ADDR
+#elif defined(CONFIG_MPC512X)
+#define CONFIG_SYS_FSL_USB_ADDR CONFIG_SYS_MPC512x_USB_ADDR
#endif
/*
* USB Registers
*/
struct usb_ehci {
- u8 res1[0x100];
+ u32 id; /* 0x000 - Identification register */
+ u32 hwgeneral; /* 0x004 - General hardware parameters */
+ u32 hwhost; /* 0x008 - Host hardware parameters */
+ u32 hwdevice; /* 0x00C - Device hardware parameters */
+ u32 hwtxbuf; /* 0x010 - TX buffer hardware parameters */
+ u32 hwrxbuf; /* 0x014 - RX buffer hardware parameters */
+ u8 res1[0x68];
+ u32 gptimer0_ld; /* 0x080 - General Purpose Timer 0 load value */
+ u32 gptimer0_ctrl; /* 0x084 - General Purpose Timer 0 control */
+ u32 gptimer1_ld; /* 0x088 - General Purpose Timer 1 load value */
+ u32 gptimer1_ctrl; /* 0x08C - General Purpose Timer 1 control */
+ u32 sbuscfg; /* 0x090 - System Bus Interface Control */
+ u8 res2[0x6C];
u16 caplength; /* 0x100 - Capability Register Length */
u16 hciversion; /* 0x102 - Host Interface Version */
u32 hcsparams; /* 0x104 - Host Structural Parameters */
u32 hccparams; /* 0x108 - Host Capability Parameters */
- u8 res2[0x14];
+ u8 res3[0x14];
u32 dciversion; /* 0x120 - Device Interface Version */
u32 dciparams; /* 0x124 - Device Controller Params */
- u8 res3[0x18];
+ u8 res4[0x18];
u32 usbcmd; /* 0x140 - USB Command */
u32 usbsts; /* 0x144 - USB Status */
u32 usbintr; /* 0x148 - USB Interrupt Enable */
u32 frindex; /* 0x14C - USB Frame Index */
- u8 res4[0x4];
+ u8 res5[0x4];
u32 perlistbase; /* 0x154 - Periodic List Base
- USB Device Address */
u32 ep_list_addr; /* 0x158 - Next Asynchronous List
- - Endpoint Address */
- u8 res5[0x4];
+ - End Point Address */
+ u8 res6[0x4];
u32 burstsize; /* 0x160 - Programmable Burst Size */
+#define FSL_EHCI_TXPBURST(X) ((X) << 8)
+#define FSL_EHCI_RXPBURST(X) (X)
u32 txfilltuning; /* 0x164 - Host TT Transmit
pre-buffer packet tuning */
- u8 res6[0x8];
+ u8 res7[0x8];
u32 ulpi_viewpoint; /* 0x170 - ULPI Reister Access */
- u8 res7[0xc];
+ u8 res8[0xc];
u32 config_flag; /* 0x180 - Configured Flag Register */
u32 portsc; /* 0x184 - Port status/control */
- u8 res8[0x20];
+ u8 res9[0x1C];
+ u32 otgsc; /* 0x1a4 - Oo-The-Go status and control */
u32 usbmode; /* 0x1a8 - USB Device Mode */
- u32 epsetupstat; /* 0x1ac - Endpoint Setup Status */
- u32 epprime; /* 0x1b0 - Endpoint Init Status */
- u32 epflush; /* 0x1b4 - Endpoint De-initlialize */
- u32 epstatus; /* 0x1b8 - Endpoint Status */
- u32 epcomplete; /* 0x1bc - Endpoint Complete */
- u32 epctrl0; /* 0x1c0 - Endpoint Control 0 */
- u32 epctrl1; /* 0x1c4 - Endpoint Control 1 */
- u32 epctrl2; /* 0x1c8 - Endpoint Control 2 */
- u32 epctrl3; /* 0x1cc - Endpoint Control 3 */
- u32 epctrl4; /* 0x1d0 - Endpoint Control 4 */
- u32 epctrl5; /* 0x1d4 - Endpoint Control 5 */
- u8 res9[0x228];
+ u32 epsetupstat; /* 0x1ac - End Point Setup Status */
+ u32 epprime; /* 0x1b0 - End Point Init Status */
+ u32 epflush; /* 0x1b4 - End Point De-initlialize */
+ u32 epstatus; /* 0x1b8 - End Point Status */
+ u32 epcomplete; /* 0x1bc - End Point Complete */
+ u32 epctrl0; /* 0x1c0 - End Point Control 0 */
+ u32 epctrl1; /* 0x1c4 - End Point Control 1 */
+ u32 epctrl2; /* 0x1c8 - End Point Control 2 */
+ u32 epctrl3; /* 0x1cc - End Point Control 3 */
+ u32 epctrl4; /* 0x1d0 - End Point Control 4 */
+ u32 epctrl5; /* 0x1d4 - End Point Control 5 */
+ u8 res10[0x28];
+ u32 usbgenctrl; /* 0x200 - USB General Control */
+ u32 isiphyctrl; /* 0x204 - On-Chip PHY Control */
+ u8 res11[0x1F8];
u32 snoop1; /* 0x400 - Snoop 1 */
u32 snoop2; /* 0x404 - Snoop 2 */
u32 age_cnt_limit; /* 0x408 - Age Count Threshold */
u32 prictrl; /* 0x40c - Priority Control */
u32 sictrl; /* 0x410 - System Interface Control */
- u8 res10[0xEC];
+ u8 res12[0xEC];
u32 control; /* 0x500 - Control */
- u8 res11[0xafc];
+ u8 res13[0xafc];
};
#endif /* _EHCI_FSL_H */
projects / project / bcm63xx / u-boot.git / commitdiff